Since the first commit 09883194f8 that introduced cortex_m, the
code has a delay of 50ms after srst has been asserted.
The specific delay is implemented through the JTAG_SLEEP command
sent in the jtag queue.
To remove the dependency from the jtag queue, replace the delay
with a transport independent function.
In case of jtag transport, this change keeps the same behaviour
only if the jtag queue has been flushed before the delay. This
does not happen if the call to dap_dp_init(), few lines above,
fails while calling a dap_queue_dp_{read,write}(); in this case
the jtag queue will be flushed later, after the delay, while in
the original code the delay would follow the flushing of the
commands already queued. Anyway, this different behavior would
only happen in case of DAP already not responsive so anticipating
the delay in such error condition is not supposed to add further
problems.
Change-Id: If15978246764e4266b10e707d86c03e5ed907de7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4912
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The implementation-defined bits have different semantics for each bus
and different recommended defaults.
Change-Id: I562fe24643bb1f3abc696339e382a75ccf2f2873
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a copy of handle_md_output() from src/target/dsp563xx.c
Change-Id: Iadd003fd1dcdbc7990d46a58ee2e7c30826ac6af
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5175
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
By definition the EXTERNAL bit in Debug Fault Status Register indicates
that an external debug request (EDBGRQ) signal was asserted.
Usage example: this could be done by CTI in multicore devices in order to
halt all the cores together.
Change-Id: I7830455ce5da6702b7d08c8fa7bfe80e4d8a5055
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5157
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Left unused after commit "target: unify memory read/write
commands", can be removed.
Change-Id: Iea6ef9204c8071283a66a679b3d6edbb0c929c5c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5153
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Fix small SBA bug.
We were not compliant with the spec, but I'm not sure if this was
causing problems for anybody.
Change-Id: Ia31ee400fd75ad907349c4dd995b1e03bd2116c7
* Don't write sbcs while sbbusy is set.
Probably not hurting anything, but the spec says we shouldn't.
Also propagate more errors, and fully decode sbcs in debug output.
Change-Id: I1a36646772fe794c8780702565103a309bbcc5e9
Currently the RISC-V compliance test suite doesn't output the test is
currently runs before it succeeds. It also uses the same message for
many tests. This makes it very hard to find out which test fails.
This commit makes things slightly easier by printing the test that's
being executed before it actually runs, and by adding the source code
line where the test is located, making it easier to look up the test in
the source code.
New output looks like this:
Info : Executing test 149 (riscv-013.c:3800): Regular calls must return ERROR_OK
Info : PASSED
The test assumes that the target has been examined. If that fails (for
whatever reason) the test will segfault:
Program received signal SIGSEGV, Segmentation fault.
register_cache_invalidate (cache=0x0) at ../src/target/register.c:109
109 struct reg *reg = cache->reg_list;
(gdb) bt
0 register_cache_invalidate (cache=0x0) at ../src/target/register.c:109
1 0x0000000000520735 in riscv_invalidate_register_cache (target=target@entry=0x779b50) at ../src/target/riscv/riscv.c:2160
2 0x000000000052224f in riscv_halt_all_harts (target=target@entry=0x779b50) at ../src/target/riscv/riscv.c:2022
3 0x0000000000574e82 in riscv013_test_compliance (target=0x779b50) at ../src/target/riscv/riscv-013.c:3600
Part of the output is generated with log functions.
Change prototype of find_target() and use command_print() for all
the output of the command.
Change-Id: Ia9fdb653fd5b27be427381053a037545faa34414
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5092
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_dump*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ia43bff112372cbb76e1aea9f59f4a9b6df05c15d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5079
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of esirisc_trace_analyze*() functions to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ie7cfd323fe591a987ea648a20be2bb9c7273dde8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5078
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of binprint() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5ebdc50417d97c791c98ac0cfe2218319809eb7f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5077
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_set() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: If00f9cfb784b53bb3df92d4469178e2f930a146a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5076
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_bp_command_list() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibff636d476bcd59784ce3da5409d930225cfe637
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5075
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I2150201fad3fd3bc0be89249dcbd314b38a6f860
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5074
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of dap_rom_display() and dap_info_command() to
pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Idb97b20759c03fcecbac1184c354966f469caa5f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5073
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of etmv1_analyze_trace() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic923af5480a54c7272d2ff1abbe235ba941cf1a0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5072
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_iod_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I67f594c80d6bbbbf6c9567069a545f16877b1e94
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5071
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm7a_handle_l2x_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib926cd7380ac8b6fb89f64e0a85d81d124633315
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5070
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv7a_handle_cache_info_command() to pass CMD
instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I27f507869cb41c74722a759e69dfd45658fcd4be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5069
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of armv4_5_handle_cache_info_command() to pass
CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib6ab3ec2fc6504c2a0635b654697a4b6e12a3750
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5068
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of handle_md_output() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib0b84c933689ac8c940c9bbe62d9c95fd015c4f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5067
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of display_cache_info(),
armv8_handle_inner_cache_info_command() and
armv8_handle_cache_info_command() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I13519c79af82cdba57d5205ba84a5a27fce65a36
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5066
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of xscale_display_instruction() and of
xscale_analyze_trace() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I8420f19c1b2ff0d2a2f2a8d3627767f7acda437c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5065
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of xscale_verify_pointer() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Id047fab41ec4f673a46756b0ab901e659e088544
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5064
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of mips_m4k_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I9fa3e883d2ca9cc858caaefd33586f78638702f5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5063
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of mips32_verify_pointer() to pass CMD instead of
CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ic4a4de10518ee009d6df420e7278fd028e1f22ca
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5062
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of cortex_m_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Icf6d1e5f8b4a3ce115c4253e49769df19a5211ae
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5061
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm946e_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ib7119e2b009d05eec47b50c3b9d32feaebc97538
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5060
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm720t_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I7fa0628fabacd9ceb62ce921192f88edca659c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5059
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm966e_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I92745591256ad56a588b6386842028e0b18dec96
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5058
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm926ejs_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: Ibbb03429a7fe8b9979f9bb9e513f9eb86aee3b5b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5057
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of arm920t_verify_pointer() to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I9a603d7c032df91b3913aadb242de89dbed0358e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5056
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
When dumping traces or semihosting text, the command that enabled
it is already completed, so CMD is not a valid value.
Plus, we want the dump to be printed in the command context where
the enable command was executed.
Replace command_print() with command_output_text().
Change-Id: I297a2b799a914233499641062407cf6e8b9fe012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5051
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Current code provides two independent implementations for the
memory read/write commands:
a) jim_target_md()/jim_target_mw() for the target specific
commands "<target> m[dw][bhw]"
b) handle_md_command()/handle_mw_command() for the current target
commands "m[dw][bhwd]"
The case a) misses the handling of doubleword and calls functions
command_print_sameline() with first parameter NULL because defined
as jim handler.
Remove the code in jim_target_md()/jim_target_mw() and use the
same code in b) for the target specific memory read/write.
This approach also provides support for 64-bit data size, not
present in the implementation in a).
The only drawback is that the implementation of memory read in b)
prints the data also as human readable ASCII characters, feature
missing in the implementation in a). This could introduced later
if it's really needed.
Update the documentation to:
- add 64-bit support
- add phys parameter
- add the count parameter
Add attribute "unused" to target_buffer_get_u8(), now not used
anymore.
Change-Id: Ib11ff924c409ad87e77fe708d628b2cc82b74d6a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5050
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Events are supposed to be executed asynchronously and not linked
with any command, so it's incorrect printing out an eventual error
using command_print().
Even in the case of events triggered by the command
<target> invoke-event <event-name>
the eventual error in the event handler is not propagated to the
command, so the command_print() is still not appropriate.
Replace command_print() with LOG_USER() in target_handle_event().
Add further info in the log to identify which event has generated
the error and its associated target.
Before return, clean-up the error message and the stacktrace from
the error already displayed, to avoid propagate them.
Change-Id: I5966aa25e7c81348f4ad4d6e7ce5d4dee44ea4c8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5049
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of target_process_reset() to pass CMD instead of
CMD_CTX.
Replace NULL parameter of command_print().
Remove extra newline, already added by command_print().
Change-Id: Ieb820c2586e1ff74a0c2b63a9c8693ca7710dfb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5048
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
jim_arm946e_cp15() used command_print() in the jim handler.
Change-Id: I0a258aad5a60f45672b9b6fa6819691507d4f0f6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5000
Tested-by: jenkins
jim_target_event_list handler used command_print() in jim handler.
Rewriting the jim handler to the OpenOCD command is easy
as get_current_target() returns proper target for prefixed commands since
bb9d9c6026
Change-Id: I3e937249386ca5dbd7a5dd6ebb0ccde0911325d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4993
Tested-by: jenkins
We have the function to wait for bits in dscr. Use it whenever
possible.
When the bit to test is DSCR_INSTR_COMP, use instead the wrapper
function cortex_a_wait_instrcmpl().
Change-Id: I5c54c239a00f489712af448eb97752210b4b38b8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In function cortex_a_wait_dscr_bits() the last read on dscr gets
ignored in case of timeout, even if it finally provides the value
that would trigger a successful return.
Check the returned value before testing the timeout.
Also, print a message on failure reading dscr.
Change-Id: I261ac1545113db39374833a55be911a4da71d893
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5112
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Depending on adapter speed, the function cortex_a_poll() can take
time to execute and can complete successfully when the timeout is
already expired. Checking the timeout at function return causes a
timeout error while that could be avoided.
Check the target status at cortex_a_poll() return, before checking
for the timeout.
Change-Id: I4c1581f6e718298c566df7b1359255e16e3955d5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5111
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
`maskisr steponly` disables interrupts during single-stepping but
enables them during normal execution. This can be used as a partial
workaround for 702596 erratum in Cortex-M7 r0p1. See "Cortex-M7 (AT610)
and Cortex-M7 with FPU (AT611) Software Developer Errata Notice" from
ARM for further details.
Change-Id: I797a14e4d43f6dcb3706528ee4ab452846ebf133
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4673
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The modified lines cause "runtime error: left shift of <X> by <Y>
places cannot be represented in type 'int'", because integer
literal is cast to int by default.
Change-Id: Ie38119b5eb46ee470e0d149959e523b48ac4d66d
Signed-off-by: Mete Balci <metebalci@gmail.com>
Reviewed-on: http://openocd.zylin.com/5005
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with SiFive HiFive1 development board.
Change-Id: I96a9a528057fcf9fc54d3da46a672d2cd54c3d5f
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4885
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Command should return target->coreid, not target->working_area_size
Solution appeared as an off topic fix in http://openocd.zylin.com/4935
Change-Id: Ic9701ce2001c75060dbaa75fbd013ed475a352e5
Suggested-by: Graham Sanderson <graham.sanderson@gmail.com>
Reported-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5035
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The missing field causes runtime debug message
BUG: command '%s' does not have the '.usage' field filled out
While there, fix some minor typo in the help messages:
s/deasert/deassert/
s/Deasert/Deassert/
Change-Id: If3dd18265cda103ca0d05609f67f4ca58e7cbb27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5024
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The missing field causes runtime debug message
BUG: command 'swd' does not have the '.usage' field filled out
Change-Id: I5a36c0fc822c4d5d74ef2d1c75e369648c6f7d4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4830
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Chained command require a subcommand as first argument. The usage
field for chained commands is not really important because the
"help" command will list all the subcommands with their respective
usage.
Add a empty usage field on all chained command.
The command "jlink config" can be either followed by a subcommand
or used alone, so use a dedicated usage string.
Change-Id: I43c3f8a766f96a9bdab4e709e3c90713be41fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5017
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no need to split the string in two lines.
Change-Id: Ifc574904acd06c31fab589643334e86f4dd0a122
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5016
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: Iefaeb15cc051db9f1e0f0140fe2f231b45f5bb12
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5013
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I65d32870bf4d3df845db69682fe445c71642f976
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I9ef7ac08e7cd5b82a6a7896c47017943d668925f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5011
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I743457acf7757df4646c9bc4e5ea1a6f9c841516
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5010
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Fixed the small typo.
Change-Id: Ia8834b23302d25e92cb2fa0802bebb2a9416595b
Signed-off-by: Mete Balci <metebalci@gmail.com>
Reviewed-on: http://openocd.zylin.com/5001
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Remove unnecessary 0.11 code.
Don't need need_strict_step anymore now that we have
riscv_hit_watchpoint().
Don't need 32-bit warning in riscv011_resume() now that address is a
target_address_t.
Change-Id: I375c023a7ec9f62d80b037ddb64d14526ba0a3dc
* WIP little refactor working towards hasel support.
Change-Id: Ie0b8dfd9e5ae2e36613fa00e14c3cd32749141bf
* More refactoring.
Change-Id: I083387c2ecff78ddfea3ed5078444732d77b909b
* More refactoring.
Change-Id: Icea1308499492da51354f89e1529353e8385f3a1
* Starting to work towards actual hasel changes.
Change-Id: If0df05ffa66cc58400b4855f9630a8b1bae3030e
* Implement simultaneous resume using hasel.
Change-Id: I97971d7564fdb159d2052393c8b82a2ffaa8833f
* Add support back for targets that don't have hasel.
Change-Id: I6d5439f0615d5d5333127d280e4f2642649a119a
* Make hasel work with >32 harts.
Change-Id: I3c55009d48bfc5dd62e3341df4e4bd21df2fe44f
Depending on how the MMU is configured it is possible to have a 1:1
mapping between virtual and physical addresses, thus making this warning
bogus. We already check that the MMU is enabled in the caller:
cortex_a_virt2phys().
Change-Id: I09f4c53ef933c8d1e268da5215a769449be014bc
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5007
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Remove the target halted check from cortex_m_remove_breakpoint()
as there is no such check in cortex_m_set_breakpoint() and bp can be
safely removed from the running target.
While on it return the error code from cortex_m_unset_breakpoint()
to higher level.
Change-Id: I2b358c3661feed84297913e9f589bdf1e4de7e64
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4887
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
fp_code_available looses sync with the real number of free comparators
as soon as cortex_m_set_breakpoint() returns an error. Remove the counter
and always go through the fp_comparator_list to find a free one.
Change-Id: I9f6e06c36d8a57ad11df5155e8a1a3aff6d833a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4870
Tested-by: jenkins
Reviewed-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Cortex-M uses only 2 byte breakpoint instruction.
cortex_m_unset_breakpoint() does not need to check breakpoint->length,
use the length as the size argument in target_write_memory()
Change-Id: I20bb869f6abce2fc61f0469e34a638bc4dc6f7ce
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4889
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Jānis Skujenieks <janis.skujenieks@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
The code for this command is currently replicated in cortex_a and
in mips_m4k and is going to be added again for cortex_m.
Plus, it is going to be obsoleted by the HW thread pseudo RTOS.
Consolidate in smp.c a single instance of the command. This will
simplify both obsoleting it and adding it to cortex_m, whatever
change comes first.
Change-Id: I03cd857e21fa3f7202fdcee36bcbd5aae30a609d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4991
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This represents months of continuing RISC-V work, with too many changes
to list individually. Some improvements:
* Fixed memory leaks.
* Better handling of dbus timeouts.
* Add `riscv expose_custom` command.
* Somewhat deal with cache coherency.
* Deal with more timeouts during block memory accesses.
* Basic debug compliance test.
* Tell gdb which watchpoint hit.
* SMP support for use with -rtos hwthread
* Add `riscv set_ir`
Change-Id: Ica507ee2a57eaf51b578ab1d9b7de71512fdf47f
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4922
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Fix indent of the macros in header file, no functional change.
Change-Id: I4d1dba5725155200148d1543c45bad919f6cd37e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4995
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
These macros are missing parenthesis around the argument, which can
lead to side effects, add them. Replace the argument name to avoid
conflict with uint32_t data type, since the macro can be applied to
other data types as well.
Change-Id: I32d2ffec6c062795d7c8bb23d1dfa3378bfc3a58
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4994
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Write to register DP_SELECT can fail, but both functions
swd_queue_dp_bankselect() and swd_queue_ap_bankselect() return
void and do not propagate the error.
Change the return type of the two functions to int and check the
returned value.
Invalidate the cached value of DP_SELECT if the write fails.
Change-Id: Iba6ef8b0c2332e7f7efb66337d558fb7a4a0d39c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4980
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the register DP_SELECT is written directly, e.g. with command
<dap> dpreg 8 <value>
the cached value in OpenOCD is not completely updated with the new
value, thus creating issues in the following AP and DP read/write
that rely on the cached value.
Update the cached value while writing to DP_SELECT.
Change-Id: I8221b10cd6fc1fbe73e6b834b68820b43480e1a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4979
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While on it add two missing new lines.
Change-Id: I0d54740479bc462b734f91686f0931824796b598
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4888
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Targets can use this to expose how many address bits there are.
gdb_server uses this to send gdb the appropriate upper limit in the
memory-map. (Before this change the upper limit would only be correct
for 32-bit targets.)
Change-Id: Idb0933255ed53951fcfb05e040674bcdf19441e1
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4947
Tested-by: jenkins
Reviewed-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If the hardware supports it, when one hart in an SMP group halts all the
other harts in that same SMP group will automatically, quickly, halt as
well.
Change-Id: Ida81f1309c180674e8c9d8060e3d2a4bbb910a6f
add command 'catch_exc' to halt a core on entering any of Secure EL1 or
EL3 or Non-Secure EL1 or EL2.
Change-Id: I0c68e247af68dd96616855a9bc1063c277d222e5
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4479
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If the function aarch64_target_create() exits for an error, the
value of pointer aarch64 get lost, causing a memory leak.
Move the allocation of aarch64 after the check on the parameters.
While there, add a check on the value returned by calloc().
Issue highlighted by clang 7.0.0.
Change-Id: Ib9ad27f4acd940da308c01fdbf33cfe51ab0c639
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4924
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If the function mem_ap_target_create() exits for an error, the
value of pointer mem_ap get lost, causing a memory leak.
Move the allocation of mem_ap after the check on the parameters.
While there, add a check on the value returned by calloc().
Issue highlighted by clang 7.0.0.
Change-Id: Ia2c11b14fde9694f28bf6efe01d278923db0f0d4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4923
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If the function cortex_a_target_create() or the function
cortex_r4_target_create() exit for an error, the value of pointer
cortex_a get lost, causing a memory leak.
Move the allocation of cortex_a after the check on the parameters.
While there, add checks on the value returned by calloc().
Issue highlighted by clang 7.0.0.
Change-Id: Ic6eeb9c3b39922d016f6d0319eada1a97a6681f0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4925
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
handle_bp_command_set() showed the error message
"Failure setting breakpoint, the same address(IVA) is already used"
on any error returned from (xxx_)breakpoint_add().
Paradoxically breakpoint_add() returned ERROR_OK if it detected
duplicated bp address.
context_breakpoint_add() and hybrid_breakpoint_add() returned -1
instead of OpenOCD compatible error if they detected duplicity.
Introduce ERROR_TARGET_DUPLICATE_BREAKPOINT
Unify error handling to LOG_ERROR() any error in (xxx_)breakpoint_add()
Remove misleading error messages from handle_bp_command_set()
handle_bp_command_set() returns error if the target does not implement
add_context_breakpoint or add_hybrid_breakpoint.
Change-Id: If17dfad1756d82a77028ebdc4b305f9c8e1365ba
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4871
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested with SiFive HiFive1 development board.
Change-Id: Ie0d9fa0899804d17ccdd84b03ba4028e97b632b8
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4884
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Implement riscv_get_thread_reg().
This is necessary because riscv_get_gdb_reg_list() now reads all
registers, which ended up causing `-rtos riscv` to read all registers
whenever one was requested (because the register cache is wiped every
time we switch to a different hart).
CustomRegisterTest went from 1329s to 106s.
Change-Id: I8e9918b7a532d44bca927f67aae5ac34954a8d32
* Also implement riscv_set_reg().
Now all the `-rtos riscv` tests pass again, at regular speed.
Change-Id: I55164224672d9dcc9eb4d1184b47258ff3c2cff1
* Better error messages.
Change-Id: I4125f9a54750d9d0ee22c4fa84b9dd3f5af203f5
* Add target_get_gdb_reg_list_noread().
Being explicit about what's expected gets `-rtos riscv` back to `-rtos
hwthread` time.
Change-Id: I6e57390c2fe79b5e6799bfda980d89697e2e29f7
* Revert a change I made that has no effect.
I don't understand exactly what all this test protects against, and I
shouldn't change it unless I do.
Change-Id: Ib329d4e34d65d2b38559b89b7afb3678f439ad2c
Fix "Potential leak of memory pointed to by 'cortex_m'"
and test for NULL return from calloc in cortex_m_target_create()
Change-Id: I4d2bb5bccc57f0ed60696f3d588297a858b8ea60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4881
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added an error msg in case of no memory
Change-Id: I7a7d266ca4aa1e4a0ff02a2d1cc672a3cd2746c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4882
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix the write only out params TODO on armv7m.c
Fix conditional move depends on uninitialised value.
It was detected while programming a LPC8Nxx with a FTDI adapter.
valgrind --leak-check=full --show-leak-kinds=all --track-origins=yes
[...]
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E4D3: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E4D3: ftdi_swd_queue_cmd (ftdi.c:1206)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
==8696==
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E506: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E506: ftdi_swd_queue_cmd (ftdi.c:1207)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
Change-Id: I50f9a8c4516b686cf62ac3c76f47c53465e949da
Signed-off-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-on: http://openocd.zylin.com/4811
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without this change xxx_start_algorithm() writes all register
parameters no matter of their direction. It usually results
in writing of uninitialized reg_params[].value - possibly
reported by valgrind.
While on it fix the wrong parameter direction in
kinetis_disable_wdog_algo(). This bug did not have any
impact because of unconditional write of reg_params.
Change-Id: Ia9c6a7b37f77d5eb6e5f5463012dddd50471742b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4813
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Stepping in the maskisr auto mode sets breakpoint to step over interrupt
service tasks. If the device has FPB rev 1, setting hard breakpoint
is impossible on address over 0x1fffffff.
Use soft type breakpoint for adresses over 0x1fffffff if FPB is rev 1.
This may eventually fail if the code memory is not writeable, but there
is nothing to do in such case.
Change-Id: Ibdeeb506903a35d550b64f82c24c37a668de62b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4857
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The functions dap_to_jtag() and dap_to_swd() have been introduced by
3ef9beb52c ("ADIv5 DAP ops switching to JTAG or SWD modes") in
arm_adi_v5.c by using the JTAG queue only.
Later, in 6f8b8593d6 ("ADIv5 transport support moves to separate
files") the functions has been moved in adi_v5_swd.c and adi_v5_jtag.c
but keeping the dependency from JTAG queue.
The functions does not work if the current transport is not JTAG.
Move back the functions in arm_adi_v5.c, replace the input parameter
"target" with "dap", use the transport to detect if the JTAG queue is
present, in case of SWD transport use the proper method, for other
transports report error.
Reuse the ADI v5 sequences already present in jtag/swd.h.
Also, OpenOCD does not support switching to another transport after
the initial selection, so do not change DAP's ops vector.
Change-Id: Ib681fbaa60cb342f732bc831eb92de25afa4e4db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4852
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Treat ARM_MODE_SYS like all other Aarch32 processor modes,
except for the special case of missing SPSR.
Change-Id: I60b21703659b264f552884cdc0f85fd45f7836de
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4494
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
A target created after init lacks target_init_one() call
and is not added to gdb targets.
Steps to reproduce:
- start OpenOCD with a dap target
- connect by telnet
target create ap0.mem mem_ap -dap $_CHIPNAME.dap -ap-num 0
reset
Segmentation fault is rised because target->check_reset is NULL.
Change-Id: I2a62f3b450e4db3005c7041a22fb8f952e68c3b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4842
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Without this change TARGET_DEBUG_RUNNING changes to TARGET_RUNNING
after adapter_poll()
Change-Id: I1c965a43527b50fa723d78fb6eae56585a7ede03
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4820
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
All the commands in OpenOCD have been inspected and have the
command mode initialize, apart for two of them.
This is not critical, because the uninitialized value (0) is
equivalent to the enum COMMAND_EXEC, that is also the correct
value for the two mentioned commands.
To keep the code consistent, initialize the command mode to
COMMAND_EXEC.
Change-Id: Iaf043364cbd1005418d787ed045a3ec653612382
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The encoding of BKPT instruction is 0xE12###7#, where the four '#'
characters should be replaced by the 16 bits immediate value.
The macro uses an incorrect shift amount, thus the immediate value
is not properly coded and bits 20~23 of the opcode could get
corrupted.
Fixed by using the proper shift amount.
Change-Id: I32db8224ab57aad6d3b002f92f9f259056593675
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4854
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Previously the code made the assumption (which is valid for conventional
RTOSs) that special registers (e.g. CSRs) are the same across threads.
26/45 tests pass.
Change-Id: Ibb3398790d7354a995d506772375d869f608f1f0
This patch covers the fact that cortex_m could be resumed externally by
Cross Trigger Interface or by direct write to DHSCR ...
To reproduce:
- halt the target
- then run the core through DHCSR (mww 0xe000edf0 0xa05f0001)
=> this resumes the core, but target state in OpenOCD remains HALTED.
Change-Id: Ifa1ae18645bfeb863acc78a039bbf04873fd78fe
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4817
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cortex_a_debug_entry and update_halt_gdb are called in two consecutive
conditions which are complementary, so externalizing the common code
makes the conditions' body lighter
With the removal of LOG_DEBUG(" ") since it does not look too informative
Change-Id: I0c54e413619576bb3af164f2dcf256c5a862c5fd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4832
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
aarch64-linux-gnu-gdb 8.2 uses "aarch64" as default architecture,
but also supports the value "aarch64:ilp32" and all the values
supported by arm-none-eabi-gdb.
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for aarch64 target to "aarch64".
Change-Id: I63e9769f47d8e73f048eb84fa73e082dd1c8e52c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4755
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
arm-none-eabi-gdb 8.2 uses "arm" as default architecture, but also
supports the following values: "arm_any", "armv2", "armv2a",
"armv3", "armv3m", "armv4", "armv4t", "armv5", "armv5t", "armv5te",
"armv5tej", "armv6", "armv6k", "armv6kz", "armv6-m", "armv6s-m",
"armv6t2", "armv7", "armv7e-m", "armv8-a", "armv8-m.base",
"armv8-m.main", "armv8-r", "ep9312", "iwmmxt", "iwmmxt2", "xscale".
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for all arm targets to "arm".
Change-Id: I176cb89878606e1febd546ce26543b3e7849500a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4754
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
The gdb patches for stm8 are still not merged in the official
repository and are temporarily hosted in
https://stm8-binutils-gdb.sourceforge.io/
The latest patch set
stm8-binutils-gdb-sources-2018-03-04.tar.gz
define only one possible value ("stm8") for this architecture; it
can be displayed typing "set architecture " followed by a TAB for
autocompletion in gdb for stm8.
Set the gdb architecture value for stm8 to "stm8".
Change-Id: I643ceba662de46cecf061d1dc672b9178a077f1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4753
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
xPSR.T sets the processor to Thumb mode when set to 1. ARMv7-M only
supports execution of Thumb instructions, so it must always be set to 1.
If xPSR.T is set to 0 on armv7m, a usage fault is generated when a
instruction execution is attempted.
On armv7m, issuing a reset causes the vector table to be examined. PC
and xPSR.T are loaded from the vector table at byte offset 4. xPSR.T is
taken from the least significant bit this value, PC from the remaining
bits. This occurs even with `reset halt`, as the reset itself causes
this load to occur without the execution of any instructions.
As a result of this, following a reset with a "bad" value programmed in
the vector table, openocd would be unable to run algorithms on the
target, as running them would immediately result in a usage fault due to
xPSR.T being unset (0).
Allow algorithms to run regardless of the content of the vector table by
explicitly setting xPSR so that xPSR.T=1 prior to executing an
algorithm. One can think of this as openocd more closely emulating a
reset or branch instruction in executing it's algorithms.
Ticket: https://sourceforge.net/p/openocd/tickets/203/
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: I4dc3427ab195d06c3fd780ea768027fefccc4c28
Reviewed-on: http://openocd.zylin.com/4658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this permits the full control of CTI from config files
Change-Id: Ia27ac8e12e08ec72da05f26dcbd81d24fa1a0f6f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4815
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target configure -work-area-xxx calls target_free_all_working_areas()
and sets the desired new parameter. Without this change the working area
does not get reallocated if it has been allocated before.
target_free_all_working_areas() results in work area containing one block
marked as free.
Completely free working area in target_free_all_working_areas()
Change-Id: I79c681082f32f2a96a2b40eb3b8751e427549693
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4797
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The block of code moved without any changes
Change-Id: I70b82dc3315dcc3f34de0537b362bee230007d02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove option 'srst' which is not recognized from on-line help and texi.
Check parameter and return syntax error if wrong option is entered.
Change-Id: I87daa423a9f53193a0b015080594820b933628f5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4795
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Cortex-M0, M0+ and M1 do not support VECTRESET bit in AIRCR.
Without this change the 'reset' command silently fails if VECTRESET
is requested.
Detect these cores, show warning if VECTRESET is about to use
and use SYSRESETREQ instead.
Change-Id: Ief174373e3ef0e6b287c57911c0aca4dfa8209f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4794
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This commit adds TARGET_HALTED check in armv8_get_core_reg32()
and armv8_set_core_reg32() to void a crash issue when gdb connects
but fails to halt the ARM core. Similar logic can be found in
armv8_get_core_reg() and armv8_set_core_reg().
Below is the call stack information of this case when gdb connects.
(gdb) bt
regnum=regnum@entry=0, dpm=0x990110) at src/target/armv8_dpm.c:657
r=0x9c7240, regnum=0, mode=<optimized out>) at src/target/armv8_dpm.c:974
at src/target/armv8.c:1487
packet=0x8ec8e0 <gdb_packet_buffer.9962> "g",
packet_size=<optimized out>, connection=<optimized out>)
at src/server/gdb_server.c:1200
at src/server/gdb_server.c:3180
command_context=command_context@entry=0x935010)
at src/server/server.c:566
...
Change-Id: I159837b533f110998184f910a0abe48409bd58f1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/4758
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Arm architecture reference manual DDI0406C reports at page 2024 in
table C3-1 the processor behaviour on debug events depending on
the debug-mode (none, monitor or halt), mode selected through the
bits MDBGen and HDBGen in DSCR register.
The halt request is served independently from the debug-mode. Thus
it's useless to enable the halt debug-mode in cortex_a_halt() by
setting the bit HDBGen (macro DSCR_HALT_DBG_MODE).
On the other side, halting for a breakpoint, a watchpoint or a
vector catch requires being in halt debug-mode.
Today HDBGen is set only in cortex_a_halt(), so we are forced to
halt the core at least once before it can be halted for hitting a
breakpoint/watchpoint/vector-catch. This is annoying since there
is no need to halt the target to set a HW breakpoint.
Move in cortex_a_init_debug_access() the selection of the halt
debug-mode, so the mode is set during examine.
To prevent a misconfigured hardware breakpoint/watchpoint/vector
catch to halt the target when OpenOCD has already quit, return to
debug-mode none at OpenOCD exit.
Change-Id: I68a1c51de3572ca1b89e90caf7eb20374268e926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4783
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
DEBUG_WAIT is useful to debug adi_jtag issue,
and the WCR register is replaced by DLCR for DP registers update
in commit 150b7d26f2.
Change-Id: I3faa9ea8a6adacd3d5275e40382801da731db32f
Signed-off-by: YanLin Zhu <zhuyanlin@pinecone.net>
Reviewed-on: http://openocd.zylin.com/4804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
This patch adds support for instruction tracing to eSi-RISC targets. The
command interface is borrowed heavily from ETM; eSi-Trace uses a less
sophisticated model for tracing, however the setup and usage is similar.
This patch also cleans up the command interfaces of the other esirisc
command groups and adds additional debugging information to log messages
when dealing with CSRs.
This patch "finalizes" support for 32-bit eSi-RISC targets.
Change-Id: Ia2a9de79a3c7c066240b5212721fb1b7584a9a45
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4780
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When GDB analyses the status of the target it try to guess the
current stack frame and issues few memory read.
E.g. on ARM targets GDB uses R11 value as a potential frame-pointer
and reads at the address pointed by R11.
The address of such memory read is not always valid and can trigger
an address translation failure.
Replace LOG_ERROR with LOG_WARNING in case the virtual address does
not have a hit in TTB; print the virtual address in the warning
message and discriminate the two identical messages with [1]/[2].
Change-Id: I288b8cd26bec2543c4f1c16b7c06dc47d5d843d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4602
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rename dtmcontrol_idle to dtmcs_idle, because the register is now called
dtmcs.
Simplify read_memory_progbuf_inner(), getting rid of several unnecessary
variables.
Change-Id: Ibac655a45c63cf2210ab282568b54f8097526c10
* flash/nor: Add support for TI CC26xx/CC13xx flash
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
* flash/nor/nrf5: remove is_erased setting and autoerase before write
Cached flash erase state in sectors[].is_erased is not reliable as running
target can change the flash.
Autoerase was issued before flash write on condition is_erased != 1
Remove autoerase completely as it is a quite non-standard feature.
Change-Id: I19bef459e6afdc4c5fcaa2ccd194cf05be8a42b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4400
Tested-by: jenkins
* src/flash/tms470: remove testing of sectors[].is_erased state
The erase check routine checked sectors only if is_erased != 1
Check sector unconditionally.
While on it fix clang static analyzer warnings.
Change-Id: I9988615fd8530c55a9b0c54b1900f89b550345e9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4401
Tested-by: jenkins
* tcl/target/stm32f7x: configure faster system clock in reset-init
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/psoc5lp: fix compile issue on GCC 8.1.0
Issue already identified by Alex https://sourceforge.net/u/alexbour/
in ticket #191https://sourceforge.net/p/openocd/tickets/191/
src/flash/nor/psoc5lp.c:237:2: error: ‘strncpy’ output
truncated before terminating nul copying 2 bytes from a
string of the same length [-Werror=stringop-truncation]
Fix it by assigning the value to the array elements.
Change-Id: I22468e5700efa64ea48ae8cdec930c48b4a7d8fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4563
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm: Add PLD command to ARM disassembler.
Updates the ARM disassembler to handle PLD (PreLoad Data) commands.
Previously handled by printing a TODO message. There are three forms of
the command: literal, register, and immediate. Simply decode based off
of the A1 encoding for the instructions in the ARM ARM. Also fixes mask
to handle PLDW commands.
Change-Id: I63bf97f16af254e838462c7cfac80f6c4681c556
Signed-off-by: James Marshall <jcmarsh@gwmail.gwu.edu>
Reviewed-on: http://openocd.zylin.com/4348
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* mips_m4k.c: Fix build with --disable-target64
Replace PRIx64 with TARGET_PRIxADDR to avoid build problems
when --disable-target64 is used during configure.
Change-Id: I054a27a491e86c42c9386a0488194320b808ba96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4566
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/arm_adi_v5: sync CSW and TAR cache on apreg write
When using apreg to change AP registers CSW or TAR we get internal
cached value not valid anymore.
Reuse the setup functions for CSW and TAR to write them.
Invalidate the cached value before the call to force the write, thus
keeping original apreg behaviour.
Change-Id: Ib14fafd5e584345de94f2e983de55406c588ac1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4565
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: keep CSW and TAR cache updated
The call to dap_queue_ap_write() can fail and the value in CSW and
TAR becomes unknown.
Invalidate the OpenOCD cache if dap_queue_ap_write() fails.
Change-Id: Id6ec370b4c5ad07e454464780c1a1c8ae34ac870
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4564
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target: Add Renesas R-Car R8A7794 E2 target
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7790 H2 Stout board
Add configuration for the Renesas R-Car R8A7790 H2
based Stout ADAS board.
Change-Id: Ib880b5d2e1fab5c8c0bc0dbcedcdce8055463fe2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4497
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7791 M2W Porter board
Add configuration for the Renesas R-Car R8A7791 M2W
based Porter evaluation board.
Change-Id: Iaadb18f29748f890ebb68519ea9ddbd18e7649af
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4498
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7794 E2 Silk board
Add configuration for the Renesas R-Car R8A7794 E2
based Silk evaluation board.
Change-Id: I504b5630b1a2791ed6967c6c2af8851ceef9723f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
NOTE: This requires SW7[1] in position 1 (default is 0)
Reviewed-on: http://openocd.zylin.com/4532
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Factor out common R-Car Gen2 code
Factor out the code shared by all R-Car Gen2 boards into a single
file to get rid of the duplication.
Change-Id: I70b302c2e71f4e6fdccb2817dd65a5493bb393d8
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4533
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag/drivers/cmsis-dap: fix connect in cmsis_dap_swd_switch_seq()
The proc cmsis_dap_swd_switch_seq() is part of the SWD API for
this interface driver. It is valid only when the interface is
used in SWD mode.
In this proc there is the need to call, in sequence, first
cmsis_dap_cmd_DAP_Disconnect() then cmsis_dap_cmd_DAP_Connect().
The latter call requires the connection mode as parameter, that
inside cmsis_dap_swd_switch_seq() can only be CONNECT_SWD.
The current implementation is not correct and in some cases can
pass mode CONNECT_JTAG. Moreover, JTAG is optional in CMSIS-DAP
and passing mode CONNECT_JTAG triggers an error with SWD-only
interfaces.
Use mode CONNECT_SWD in SWD specific cmsis_dap_swd_switch_seq().
Change-Id: Ib455bf5b69cb2a2d146a6c8875387b00c27a5690
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4571
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: return error if breakpoint address is out of range
If the "Flash Patch and Breakpoint" unit is rev.1 then it can only
accept breakpoint addresses below 0x1FFFFFFF.
Detailed info in "ARM v7-M Architecture Reference Manual", DDI0403E
at chapter "C1.11 Flash Patch and Breakpoint unit".
Print a message and return error if the address of hardware
breakpoint cannot be handled by the breakpoint unit.
Change-Id: I95c92b1f058f0dfc568bf03015f99e439b27c59b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4535
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/stm32: Report errors in wait_status_busy
Flash operation errors that occur during algorithm programming are
reported via the algorithm return value. However, Flash operation
errors that occur during non-algorithm work (erasing, programming
without a work area, programming the last non-multiple-of-32-bytes on
an H7, etc.) generally end with a call to stm32x_wait_status_busy,
which reads the status register and clears the error flags but fails
to actually report that something went wrong should an error flag
(other than WRPERR) be set. Return an error status from
stm32x_wait_status_busy in those cases. Correct a log message
accordingly.
Change-Id: I09369ea5f924fe58833aec1f45e52320ab4aaf43
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4519
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32: Eliminate working area leak
On a specific early-return path, an allocated working area was not
freed. Free it.
Change-Id: I7c8fe51ff475f191624086996be1c77251780b77
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4520
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32h7: Fix incorrect comment
The name of the bit according to the reference manual is inconsistency
error, not increment error.
Change-Id: Ie3b73c0312db586e35519e03fd1a5cb225673d97
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4521
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* target: fix 'bp' command help message
"asid" and "length" are separate arguments of the command.
Put space between them.
Change-Id: I36cfc1e3a01caafef4fc3b26972a0cc192b0b963
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4511
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Add ARM v8 AArch64 semihosting support
This patch implements semihosting support for AArch64. This picks
code from previously submitted AArch64 semihosting support patch
and rebases on top of reworked semihosting code. Tested in AArch64
mode on a Lemaker Hikey Board with NewLib and GDB.
Change-Id: I228a38f1de24f79e49ba99d8514d822a28c2950b
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4537
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* GDB fileIO stdout support
This patch fixes gdb fileio support to allow gdb console to be used as stdout.
Now we can do something like
gdb <inferior file>
(gdb) tar ext :3333
(gdb) load
(gdb) monitor arm semihosting enable
(gdb) monitor arm semihosting_fileio enable
(gdb) continue
Here: Output from inferior using puts, printf etc will be routed to gdb console.
Change-Id: I9cb0dddda1de58038c84f5b035c38229828cd744
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4538
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target: armv8: Avoid semihosting segfault on halt
Avoid a NULL pointer dereference when halting an aarch64 core.
Change-Id: I333d40475ab26e2f0dca5c27302a5fa4d817a12f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4593
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: target: Add NXP LS1012A config
As seen on the FRDM-LS1012A board.
Change-Id: Ifc9074b3f7535167b9ded5f544501ec2879f5db7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4594
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: board: Add NXP Freedom FRDM-LS1012A config
An update for the K20 CMSIS-DAP firmware can be found here:
https://community.nxp.com/thread/387080?commentID=840141#comment-840141
Change-Id: I149d7f8610aa56daf1aeb95f14ee1bf88f7cb647
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4595
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: only trigger once the event gdb-detach at gdb quit
When GDB quits (e.g. with "quit" command) we first execute
gdb_detach() to reply "OK" then, at GDB disconnect (either TCP
or pipe connection type), we execute gdb_connection_closed().
In case GDB is killed or it crashes, OpenOCD only executes the
latter when detects the disconnection.
Both gdb_detach() and gdb_connection_closed() trigger the event
TARGET_EVENT_GDB_DETACH thus getting it triggered twice on clean
GDB quit.
Do not trigger the event TARGET_EVENT_GDB_DETACH in gdb_detach()
and let only gdb_connection_closed() to handle it.
Change-Id: Iacf035c855b8b3e2239c1c0e259c279688b418ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4585
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* gdb_server: set current_target from connection's one
In a multi-target environment we are supposed to have a single
gdb server for each target (or for each group of targets within
a SMP node).
By default, the gdb attached to a server sends its command to
the target (or to the SMP node targets) linked to that server.
This is working fine for the normal gdb commands, but it is
broken for the native OpenOCD commands executed through gdb
"monitor" command. In the latter case, gdb "monitor" commands
will be executed on the current target of OpenOCD configuration
script (that is either the last target created or the target
specified in a "targets" command).
Fixed in gdb_new_connection() by replacing the current target
in the connection's copy of command context.
Change-Id: If7c8f2dce4a3138f0907d3000dd0b15e670cfa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4586
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/image: make i/j unsigned to avoid ubsan runtime error
src/target/image.c:1055:15: runtime error: left shift of 128 by 24 places cannot be represented in type 'int'
Change-Id: I322fd391cf3f242beffc8a274824763c8c5e69a4
Signed-off-by: Cody Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4584
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/stm32f7x: Clear stuck HSE clock with CSS
Change-Id: Ica0025ea465910dd664ab546b66f4f25b271f1f5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4570
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* psoc5lp: fix erase check, add free_driver_priv
psoc5lp_erase_check() was not properly adapted to the new
armv7m_blank_check_memory() in the hot fix 53376dbbed
This change fixes handling of num_sectors in dependecy of ecc_enabled.
Also add comments how ecc_enabled influences num_sectors.
Add pointer to default_flash_free_driver_priv() to all psoc5lp flash
drivers to keep valgrind happy.
Change-Id: Ie1806538becd364fe0efb7a414f0fe6a84b2055b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4569
Tested-by: jenkins
* target: atmel samd10 xplained mini
cortex m0+ on a tiny board, with an mEDBG (CMSIS-DAP) debug interface.
Change-Id: Iaedfab578b4eb4aa2d923bd80f220f59b34e6ef9
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: add SAMD11 Xplained Pro evaluation board
Change-Id: Id996c4de6dc9f25f71424017bf07689fea7bd3af
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4507
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Adds SAMD11D14AU flash support.
Corrects names of SAMD11D14AM and SAMD11D14ASS per datasheet.
Change-Id: I8beb15d5376966a4f8d7de76bfb2cbda2db440dc
Signed-off-by: Christopher Hoover <ch@murgatroid.com>
Reviewed-on: http://openocd.zylin.com/4597
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nds32: Avoid detected JTAG clock
AICE2 doesn't support scan for the maximum clock frequency of
JTAG chain. It will cause USB command timeout.
Change-Id: I41d1e3be387b6ed5a4dd0be663385a5f053fbcf9
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/4292
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl: Distinguish between sectors and blocks in status messages
Use the right word in flash protect command status messages based on
whether the target bank defines num_prot_blocks. Minor message style
tidy-up.
Change-Id: I5f40fb5627422536ce737f242fbf80feafe7a1fc
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4573
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* drivers: cmsis-dap: pull up common connect code
Just a minor deduplication
Change-Id: Idd256883e5f6d4bd4dcc18462dd5468991f507b3
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* drivers: cmsis-dap: Print version info when available
No need to wait until after connecting, might help diagnose part information by
printing earlier.
Change-Id: I51eb0d584be306baa811fbeb1ad6a604773e602c
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3404
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor: add support for TI MSP432 devices
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/at91sam4: fix sam4sa16c flash banks and its gpnvms count
There was already a github fork that had this fixed, but as we try
to use the latest, non-modified version of all software we use,
I would like to have this fix in the next releases of OpenOCD so
that if people uses $packagemanager, they will not have issues flashing
the last part of the flash of sam4sa16c chips.
Additionally, I've added some more logging related to the flash
bank that was used, and the chip ID that was detected.
Change-Id: I7ea5970105906e4560b727e46222ae9a91e41559
Signed-off-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4599
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* flash/nor/stm32lx: Add revision 'V' for STM32L1xx Cat.3 devices
Change-Id: Ic92b0fb5b738af3bec79ae335876aa9e26f5f4cd
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4600
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid null target->semihosting references.
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: Add HWID 0x139 (52832 rev E0)
Change-Id: I71b7471ccfcb8fcc6de30da57ce4165c7fb1f73f
Signed-off-by: James Jacobsson <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4604
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target: Fix segfault for 'mem2array'
Call 'mem2array' without arguments to reproduce the segmentation
fault.
Change-Id: I02bf46cc8bd317abbb721a8c75d7cbfac99eb34e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4534
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/armv7m_trace: Fix typo in enum
Change-Id: I6364ee5011ef2d55c59674e3b97504a285de0cb2
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3904
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/armv7m_trace: Use prefix for enums
Change-Id: I3f199e6053146a1094d96b98ea174b41bb021599
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3905
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/aarch64: Call aarch64_init_debug_access() earlier in aarch64_deassert_reset()
On Renesas R-Car, calling 'reset halt' and 'reset init' always made DAP inaccessible. Calling 'reset' and 'halt' seperatly worked fine.
The only differences seems to be the point in time when aarch64_init_debug_access() is called. This patch aligns the behaviour.
Change-Id: I2296c65e48414a7d9846f12a395e5eca315b49ca
Signed-off-by: Dennis Ostermann <dennis.ostermann@renesas.com>
Reviewed-on: http://openocd.zylin.com/4607
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* server: Improve signal handling under Linux
Commit 5087a955 added custom signal handlers for the openocd
server process.
Before this commit, when openocd is run as a background process
having the same controlling terminal as gdb, Control-C would be
handled by gdb to stop target execution and return to the gdb prompt.
However, after commit 5087a955, the SIGINT caused by pressing
Control-C also terminates openocd, effectively crashing the
debugging session. The only way to avoid this is run openocd in
a different controling terminal or to detach openocd from its
controlling terminal,
thus losing all job control for the openocd process.
This patch improves the server's handling of POSIX signals:
1) Keyboard generated signals (INT and QUIT) are ignored
when server process has is no controlling terminal.
2) SIGHUP and SIGPIPE are handled to ensure that .quit functions
for each interface are called if user's logs out of X
session or there is a network failure.
SIG_INT & SIG_QUIT still stop openocd
when it is running in the foreground.
Change-Id: I03ad645e62408fdaf4edc49a3550b89b287eda10
Signed-off-by: Brent Roman <genosensor@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3963
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* armv7a: read ttbcr and ttb0/1 at every entry in debug state
Commit bfc5c764df avoids reading
ttbcr and ttb0/1 at every virt2phys translation by caching them,
and it updates the cached values in armv7a_arch_state().
But the purpose of any (*arch_state)() method, thus including
armv7a_arch_state(), is to only print out and inform the user
about some architecture specific status.
Moreover, to reduce the verbosity during a GDB session, the
method (*arch_state)() is not executed anymore at debug state
entry (check use of target->verbose_halt_msg in src/openocd.c),
thus the state of translation table gets out-of-sync triggering
Error: Address translation failure
or even using a wrong address in the memory R/W operation.
In addition, the commit above breaks the case of armv7r by
calling armv7a_read_ttbcr() unconditionally.
Fixed by moving in cortex_a_post_debug_entry() the call to
armv7a_read_ttbcr() on armv7a case only.
Remove the call to armv7a_read_ttbcr() in armv7a_identify_cache()
since it is (conditionally) called only in the same procedure
cortex_a_post_debug_entry().
Fixes: bfc5c764df ("armv7a: cache ttbcr and ttb0/1 on debug
state entry")
Change-Id: Ifc20eca190111832e339a01b7f85d28c1547c8ba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4601
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Avoid dereferencing NULL pointer.
If a NULL pointer is passed, don't attempt to increment it. This avoids
passing the now not-NULL pointer on and eventually segfaulting. Also
remove some unnecessary temporary variables.
Change-Id: I268e225121aa283d59179bfae407ebf6959d3a4e
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4550
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Remove FSF mailing address.
Checkpatch complains about this (FSF_MAILING_ADDRESS).
Change-Id: Ib46a7704f9aed4ed16ce7733d43c58254a094149
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* drivers: cmsis_dap_usb: implement cmd JTAG_TMS
Simply add a wrapper around cmsis_dap_cmd_DAP_SWJ_Sequence()
Change-Id: Icf86f84b24e9fec56e2f9e155396aac34b0e06d2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4517
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* arm_adi_v5: put SWJ-DP back to JTAG mode at exit
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add RISC-V support.
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* usb_blaster: Don't unnecessarily go through DR-/IR-Pause
There is no need to pass through DR-/IR-Pause after a scan if we want to
go to DR-/IR-Update. We just have to skip the first step of the path to
the end state because we already did that step when shifting the last
bit.
v2:
- Fix comments as remarked in review of v1
Change-Id: I3c10f02794b2233f63d2150934e2768430873caa
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/4245
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* cortex_a: fix virt2phys when mmu is disabled
When the MMU is not enabled on debug state entry, virt2phys cannot
perform a translation since it is unknown whether a valid MMU
configuration existed before. In this case, return the virtual
address as physical address.
Change-Id: I6f85a7a5dbc200be1a4b5badf10a1a717f1c79c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4480
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* drivers: cmsis-dap: print serial if available
Helpful for sanity checking connections
Change-Id: Ife0d8b4e12d4c03685aac8115c9739a4c1e994fe
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3405
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: make a variable local
The vec_ids variable is not referenced anywhere other than the vector
catch command handler. Make it local to that function.
Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4606
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: fix compile error for uninitialized variable
Commit ad6c71e151 introduced the
variable "mmu_enabled" whose pointer is passed to cortex_a_mmu()
that initialises it.
This initialization is not visible to the compiler that issue
a compile error.
The same situation is common across the same file and the usual
workaround is to initialize it to zero; thus the same fix i
applied here.
Ticket: https://sourceforge.net/p/openocd/tickets/197/
Fixes: commit ad6c71e151 ("cortex_a: fix virt2phys when mmu is disabled")
Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4619
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* mips_m4k: add optional reset handler
In some cases by using SRST we can't halt CPU early enough. And
option PrRst is not available too. In this case the only way is
to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself.
For example by writing to some reset register.
This patch is providing possibility to use user defined reset-assert
handler which will be enabled only in case SRST is disabled. It is
needed to be able switch between two different reset variants on run
time.
Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4404
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target: add config for Qualcomm QCA4531
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable
Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4405
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add config for 8devices LIMA board
More information about this board can be found here:
https://www.8devices.com/products/lima
Change-Id: Id35a35d3e986630d58d37b47828870afd107cc6a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4406
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target|board: move common AR9331 code to atheros_ar9331.cfg
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add DDR2 helper
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add documentation and extra helpers
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add DPTechnics DPT-Board-v1
it is Atheros AR9331 based IoT dev board.
Change-Id: I6fc3cdea1bef49c53045018ff5acfec4d5610ba6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4424
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* fpga/altera-10m50: add all device id
add all currently know Intel (Alter) MAX 10 device ids
Change-Id: I6a88fef222c8e206812499d41be863c3d89fa944
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4598
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target|board: Add Intel (Altera) Arria 10 target and related board
Target information about this SoC can be found here:
https://www.altera.com/products/fpga/arria-series/arria-10/overview.html
Achilles Instant-Development Kit Arria 10 SoC SoM:
https://www.reflexces.com/products-solutions/development-kits/arria-10/achilles-instant-development-kit-arria-10-soc-som
Change-Id: Id78c741be6a8b7d3a70f37d41088e47ee61b437a
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4583
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/riscv: fix compile error with gcc 8.1.1
Fix compile error:
src/target/riscv/riscv-011.c: In function ‘slot_offset’:
src/target/riscv/riscv-011.c:238:4: error: this statement may fall through
[-Werror=implicit-fallthrough=]
switch (slot) {
^~~~~~
src/target/riscv/riscv-011.c:243:3: note: here
case 64:
^~~~
Fixes: a51ab8ddf6 ("Add RISC-V support.")
Change-Id: I7fa86b305bd90cc590fd4359c3698632d44712e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4618
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* server: explicitly call "shutdown" when catch CTRL-C or a signal
Every TCL command can be renamed (or deleted) and then replaced by
a TCL proc that has the same name of the original TCL command.
This can be used either to completely replace an existing command
or to wrap the original command to extend its functionality.
This applies also to the OpenOCD command "shutdown" and can be
useful, for example, to set back some default value to the target
before quitting OpenOCD.
E.g. (TCL code):
rename shutdown original_shutdown
proc shutdown {} {
puts "This is my implementation of shutdown"
# my own stuff before exit OpenOCD
original_shutdown
}
Unfortunately, sending a signal (or pressing CTRL-C) to terminate
OpenOCD doesn't trigger calling the original "shutdown" command
nor its (eventual) replacement.
Detect if the main loop is terminated by an external signal and
in such case execute explicitly the command "shutdown".
Replace with enum the magic numbers assumed by "shutdown_openocd".
Please notice that it's possible to write a custom "shutdown" TCL
proc that does not call the original "shutdown" command. This is
useful, for example, to prevent the user to quit OpenOCD by typing
"shutdown" in the telnet session.
Such case will not prevent OpenOCD to terminate when receiving a
signal; OpenOCD will quit after executing the custom "shutdown"
command.
Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4551
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* zy1000: fix compile error with gcc 8.1.1
The fall-through comment is not taken in consideration by gcc 8.1.1
because it is inside the braces of a C-code block.
Move the comment outside the C block.
Change-Id: I22d87b2dee109fb8bcf2071ac55fdf7171ffcf4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4614
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl.c: fix flash bank bounds check in 'flash fill' command handler
Steps to reproduce ( STM32F103 'Blue Pill', 128KiB of flash ):
> flash fillh 0x0801FFFE 00 1
wrote 2 bytes to 0x0801fffe in 0.019088s (0.102 KiB/s)
> flash fillw 0x0801FFFE 00 1
Error: stm32f1x.cpu -- clearing lockup after double fault
Error: error waiting for target flash write algorithm
Error: error writing to flash at address 0x08000000 at offset 0x0001fffe
Change-Id: I145092ec5e45bc586b3df48bf37c38c9226915c1
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4516
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: add command "dpreg"
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.
Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
$dap_name dpreg reg [value]
Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: add free_driver_priv
Change-Id: I429a9868deb0c4b51f47a4bbad844bdc348e8d21
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/4608
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: add support for NuttX
This patch introduces RTOS support for NuttX. Currently,
only ARM Cortex-M (both FPU and FPU-less) targets are supported.
To use, add the following lines to ~/.gdbinit.
define hookpost-file
eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end
And please make sure the above values are the same as in
src/rtos/nuttx_header.h
Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com>
Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com>
Reviewed-on: http://openocd.zylin.com/4103
Tested-by: jenkins
Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* server/server: Add ability to remove services
Add the ability to remove services while OpenOCD is running.
Change-Id: I4067916fda6d03485463fa40901b40484d94e24e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4054
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: fix incorrect comment
The code sets C_MASKINTS if that bit is not already set (correctly). Fix
the comment to agree.
Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4620
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target/stm32f0x: Allow overriding the Flash bank size
Copy & paste from another stm32 target.
Change-Id: I0f6cbcec974ce70c23c1850526354106caee1172
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4575
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/target: add Allwinner V3s SoC support
Change-Id: I2459d2b137050985b7301047f9651951d72d9e9e
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4427
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/arm_adi_v5: allow commands apsel and apcsw during init phase
The current implementation of apsel cannot be executed during the
initialization phase because it queries the DAP AP to retrieve and
print the content of IDR register, and the query is only possible
later on during the exec phase.
But IDR information is already printed by the dedicated command
apid, making redundant printing it by apsel too.
Being unable to run apsel during initialization, makes also apcsw
command (that depends on apsel) not usable in such phase.
Modify the command apsel to only set the current AP, without making
any transfer to the (possibly not initialized yet) DAP. When run
without parameters, just print the current AP number.
Change mode to COMMAND_ANY to apsel and to apcsw.
Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4624
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: allow command dacrfixup during init phase
There is no reason to restrict the command "cortex_a dacrfixup"
to the EXEC phase only.
Change the command mode to ANY so the command can be used in
the initialization phase too.
Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4623
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/armv7a_cache: add gdb keep-alive and fix a missing dpm finish
Depending on range size, the loop on cache operations can take quite
some time, causing gdb to timeout.
Add keep-alive to prevent gdb to timeout.
Add also a missing dpm->finish() to balance dpm->prepare().
Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4627
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add detail to `wrong register size` error.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Id31499c94b539969970251145e42c89c943fd87c
Reviewed-on: http://openocd.zylin.com/4577
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* doc: fix typo in cortex_m maskisr command
Change-Id: I37795c320ff7cbf6f2c7434e03b26dbaf6fc6db4
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4621
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: restore C_MASKINTS after reset
The cortex_m maskisr user-facing setting is not changed across a target
reset. However, the in-core C_MASKINTS bit was always cleared as part of
reset processing, meaning that a cortex_m maskisr on setting would not
be respected after a reset. Set C_MASKINTS based on the user-facing
setting value rather than always clearing it after reset.
Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4605
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: update all uses of interface/stlink-v2-1 to interface/stlink
Change-Id: I5e27e84d022f73101376e8b4a1bdc65f58fd348a
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4456
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/riscv/riscv-011: fix compile warning about uninitialized variable
In MSYS2 MinGW 64-bit
git clone git://git.code.sf.net/p/openocd/code openocd
$ gcc --version
gcc.exe (Rev1, Built by MSYS2 project) 8.2.0
./bootstrap
./configure --prefix=
$ cat config.status | grep CFLAGS
CFLAGS='-g -O2'
make bindir = "bin-x64"
depbase=`echo src/target/riscv/riscv-011.lo | sed 's|[^/]*$|.deps/&|;s|\.lo$||'`;\
/bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF $depbase.Tpo -c -o src/target/riscv/riscv-011.lo src/target/riscv/riscv-011.c &&\
mv -f $depbase.Tpo $depbase.Plo
libtool: compile: gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF src/target/riscv/.deps/riscv-011.Tpo -c src/target/riscv/riscv-011.c -o src/target/riscv/riscv-011.o
src/target/riscv/riscv-011.c: In function 'poll_target':
src/target/riscv/riscv-011.c:1799:6: error: 'reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
reg_cache_set(target, reg, ((data & 0xffffffff) << 32) | value);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/target/riscv/riscv-011.c:1686:17: note: 'reg' was declared here
unsigned int reg;
^~~
cc1.exe: all warnings being treated as errors
make[2]: *** [Makefile:3250: src/target/riscv/riscv-011.lo] Error 1
Change-Id: I6996dcb866fbace26817636f4bedba09510a087f
Signed-off-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
Reviewed-on: http://openocd.zylin.com/4635
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* max32xxx: Support for MAX32XXX devices.
Adding flash programming support for Maxim Integrated MAX32XXX
devices.
Change-Id: I5b0f57a885f9d813240e4bc2d9f765b743e1cfc3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/3543
Tested-by: jenkins
Reviewed-by: Ismail H. KOSE <ihkose@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* flash/at91sam4: run probe just once
Reread registers in sam4_GetInfo()
Change-Id: I3b023b3e642a9c052b5c41673d196317f7e7f2e3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4609
Tested-by: jenkins
Reviewed-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
* flash/at91sam4: emit flash bank info
Change related LOG_INFO to LOG_DEBUG
Change-Id: I0c09b1ec83da631b26980dc8632b9031fe2921a3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4610
Tested-by: jenkins
Reviewed-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
* flash/at91sam4: set wait states only once per write
Read-modify-write setting of FMR register requires an USB turnaround.
Setting FMR before each page write is not necessary and decreases the
write speed.
Change-Id: I67844c898aaf117f155c762c979840b603c767ed
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4611
Tested-by: jenkins
Reviewed-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
* flash/at91sam4: fix clang static analyzer warning
Change-Id: I5e5319d855c868adfa012f68086f7f809ec5a069
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4639
Tested-by: jenkins
* rtos/linux.c: fix clang static analyzer warning
Remove sizeof(int64_t) from string size computation.
Change-Id: I029b394df5d62a2594a723c4c0e13608b3423b9b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4640
Tested-by: jenkins
* target: armv8: Ensure target is halted for virt2phys
Othewise the error reported as
Timeout waiting for dpm prepare
Change-Id: Ieed2fdcd94ae4e877a749df3eec07a01dbf80b10
Closes: https://sourceforge.net/p/openocd/tickets/201/
Found-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Guido Günther <guido.gunther@puri.sm>
Reviewed-on: http://openocd.zylin.com/4647
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* adi_v5: enforce check on AP number value
The AP number value is restricted in 8 bits unsigned by ADI-v5
specification. Nevertheless, an "invalid" value is used by
target cortex-m to force an automatic detection of the AP.
Replace magic numbers by using new macros for AP max number and
for the value of AP invalid.
Check the value passed through -ap-num flag during configuration.
Change-Id: Ic19a367db0ab11c0ebd070750eca0647d25279a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4668
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: add per target option "-gdb-port"
The argument passed to global config command "gdb_port" is usually,
but not always, a TCP port number. In case of multiple targets, this
numeric value is used as the first port of a set of consecutive TCP
ports assigned one per target.
If the argument is not a numeric value (e.g. "pipe", "disabled", ...)
then incrementing it for the next target has no sense.
Add the option "-gdb-port number" to the commands "target create" and
"$target_name configure" to override, for the specific target, the
general global configuration.
This permits to use a per target "-gdb-port disabled", when no gdb
port is required for that specific target.
It also makes possible to choose a custom TCP port number for each
target, overriding the usual sequence of consecutive port numbers.
Change-Id: I3b9a1910b28ab4bc757e839d0e5d08ffc29f7ab4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4530
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* libusb: return oocd error values
keep same return style where possible
Change-Id: I2f9b85dbc307a483609f76a84de77e3c74d346c7
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4588
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* rtos-helpers: fix minor typo in uC/OS-III helper
This patch corrects a spelling error in uCOS-III-openocd.c.
Change-Id: I6d1923ff1f5e6361358c45cec3dd6c08ca9ccef0
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4659
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/stm32f2x: add stm32f7 revision Z identification
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Change-Id: Ia0169514d494bae2a98d92ebc97c8eccc10bc6c4
Reviewed-on: http://openocd.zylin.com/4657
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/mem_ap: generic mem-ap target
This pseudo target allows attaching to any access point on the DAP at the
MEM-AP level and read and write addresses on the connected bus. For
example, one can create a mem_ap target on the APB-AP and read and write
registers of debug components directly. This allows many diagnostic
and other features be programmed entirely using TCL, without necessity
of adding drivers to OpenOCD.
Change-Id: I53229ffd68fb0f96fb68be15b0f3a76cc8843c8e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4002
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Leonard Crestez <cdleonard@gmail.com>
* interface: adapter configuration for FTDI C232HM
This patch adds support for the C232HM-DDSL-0 and C232HM-EDSL-0
FT232H-based cables from FTDI. For more information, see:
http://www.ftdichip.com/Products/Cables/USBMPSSE.htm
Change-Id: Ic97423eb1e2f6b5ebae04943cd5cce86f38771d5
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4081
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* ftdi: extend ftdi_location format
To existing <bus>:<port>,<port> format add <bus>-<port>.<port> support.
The last format is used by kernel and other drivers.
Change-Id: I6528970d3af4f6a8bf7b27a0f7a763b5957fdf2b
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4631
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: poll all targets in SMP node after halt
The periodic poll scans all the targets in the same order they
have been declared in the configuration file.
When one target in a SMP node halts, the transition is detected
in the following poll and this triggers a halt request to all the
other cores of the SMP node.
The targets that will be polled afterwards will be identified as
"halted", but the targets already scanned will remain as
"running" until the next periodic poll.
This creates a race condition with GDB; GDB sets the breakpoints
when runs the target and removes them as soon as the target is
halted. When it receives the halt event, it starts removing the
breakpoints and fails on the targets that are still reported as
"running".
Fixed by polling all the targets in the SMP node before informing
GDB about the halt event.
This implementation is almost copy/paste from the one in aarch64.
Change-Id: Id2bd99f1e56b014e48e9e34ccb891b4219c518f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4622
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Emcraft imx8 SOM BSB support
Tested with Olimex ARM-USB-TINY-H adapter
Simple commands work fine but there are currently issues when attaching
remote gdb or running virt2phys:
https://sourceforge.net/p/openocd/tickets/201/
Change-Id: I86ccf1d93c5d23870bb522f92b3e2af190d529e8
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-on: http://openocd.zylin.com/4646
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* arm_adi_v5: remove useless cast to int
The field ap_num in struct adiv5_private_config is already of type int.
Casting it to type int has no sense.
Change-Id: Ida642e808c02591bb58609425eccd096d404e2c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4666
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nrf5: time-based timeout waiting for flash controller
Change-Id: Id214df154dc359ca130c8d8fe1554d106621b9cd
Signed-off-by: Kai Geissdoerfer <kai.geissdoerfer@tu-dresden.de>
Reviewed-on: http://openocd.zylin.com/4648
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nrf5: support for nRF52840 Q1AAC0
Change-Id: Id3280dadece84e1d68544936e44d506c7930a55d
Signed-off-by: Kai Geissdoerfer <kai.geissdoerfer@tu-dresden.de>
Reviewed-on: http://openocd.zylin.com/4649
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* doc: fix use of deprecated config file in the example
Commit 31c58c139d ("jtag: drivers: stlink: handle all versions with
single config") deprecates the use of "interface/stlink-v2-1.cfg" in
favor of a unique config file "interface/stlink.cfg".
Update the example in the documentation.
Change-Id: I1aed7c70e15f4edb4f81a3ee8e3bce575fde873b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4667
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Added support for STM32L4X option bytes writing.
Enables the programming of Write protection lock bits.
- Updated/re-factored with option_read, option_write and option_load commands.
Change-Id: I86358c7eb1285c3c0baac1564e46da8ced5fd025
Signed-off-by: Thomas Søhus <tls@ceepro.dk>
Reviewed-on: http://openocd.zylin.com/4654
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Clarify what exactly the RISC-V code supports.
Change-Id: I8da657426cc52c738ab41bfb0164cbc6721c0aef
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4655
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: fix typo
The subunit of the debug unit is called the Flash Patch and Breakpoint
unit, abbreviated (by ARM no less) as FPB, not FBP.
Change-Id: Ia2f08470da705f0f1518feeca878f0f500507308
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4675
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* contrib/60-openocd.rules: provide hint to reload udev rules
No need to reboot the Linux box when new rules are added to udev.
Suggest the command in the script header.
Change-Id: Ie95383bfd73914a3d2e2c05d77fa3eb32e68b7e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4665
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* target/stm32: make APCSW cacheable
Change-Id: I7c5c9720ded329848647f17db95f845e46c01c19
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4674
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/atsamv: make APCSW cacheable
Change-Id: Ic00d3192642c682f370a6f7f8b70ae29744eb746
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4678
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* gdb_server: avoid gdb server for virtual targets
Virtual targets, like mem_ap, do not or cannot implement the required
functionality to accept a GDB connection. In the case of mem_ap, the
method get_gdb_reg_list() is missing and a following connection from
gdb causes OpenOCD to segfault.
OpenOCD opens a GDB port for each target; it's always possible to
connect, by mistake, GDB to one virtual target.
Add a method to check if the target supports GDB connections (for the
moment just checking if get_gdb_reg_list is implemented).
Skip opening a gdb server for every targets that don't support GDB
connections.
Change-Id: Ia439a43efe1a9adbb1771cd9d252db8ffa32eb9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4676
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/target: Add Renesas R-Car Gen3 targets
Add configuration for the Renesas R-Car Generation 3 targets.
These are SoCs with Cortex A57s, A53s, and R7s. All cores
are supported.
Change-Id: I795233210e4f647a1a2a0adea7c058ae98b5db70
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4669
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car Salvator-X(S) boards.
Add configuration for the Renesas R-Car Salvator-X
and Renesas R-Car Salvator-XS boards.
Change-Id: I898008f56adb31908d30760f18217583fabf1c51
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4670
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* flash/nrf5: support for nRF52810
Change-Id: I01c430bfa593d20ea7a51c90d67052e374d239b3
Signed-off-by: Anders Westrup <anders@westrup.se>
Reviewed-on: http://openocd.zylin.com/4680
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Slowcoder <slowcoder@gmail.com>
* drivers: cmsis-dap: fix connection in JTAG mode
Commit 5aceec2412 ("drivers:
cmsis-dap: pull up common connect code") breaks the driver and it
cannot connect anymore in JTAG mode.
The issue is caused in cmsis_dap_init() by anticipating the call to
cmsis_dap_usb_open(), which then sets cmsis_dap_handle and makes the
following test to always fail.
Actually the original code was quite tricky:
if (swd_mode)
do something that also sets cmsis_dap_handle;
if (cmsis_dap_handle == NULL)
do something for !swd_mode;
Convert the sequence of tricky "if"s in a single "if-then-else" to
handle clearly the cases swd_mode and !swd_mode.
Change-Id: I359a23bf26a3edc2461f4352daa0be83e78868f7
Fixes: 5aceec2412 ("drivers: cmsis-dap: pull up common connect code")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4697
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* register: support non-existent registers
This patch fixes a number of bugs caused by incomplete support for
non-existent registers. This is needed for targets that provide optional
registers or non-linear register numbers.
Change-Id: I216196e0051f28887a2c3da410959382369eed80
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* rtos: support gdb_get_register_packet
This patch adds support for p packet responses by targets configured
with RTOS support. This change required moving to a rtos_reg struct,
which is similar to struct reg used by targets, which resulted in
needing to update each stacking with register numbers. This patch also
allows targets with non-linear register numbers to function with RTOSes
as well.
Change-Id: I5b189d74110d6b6f2fa851a67ab0762ae6b1832f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4121
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: add support for architecture element
This change adds optional support for a target to report architecture
information in the target description to GDB. This is needed by some GDB
implementations to properly support remote target with custom behavior.
More information on the architecture element can be found here:
https://sourceware.org/gdb/onlinedocs/gdb/Target-Description-Format.html#Target-Description-Format
Change-Id: I57b19cae5ac3496256e4e5cc52cf6526ca5c322d
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4078
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag: make cmd_queue_scan_field_clone public
This patch makes the cmd_queue_scan_field_clone function public. This
permits targets to insert fields without affecting the submitted
scan_field list. This will be used in an upcoming target implementation
that needs to insert additional padding bits.
Change-Id: I8fbd3b9b4e413432471f4f1444048932c8fa189e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4082
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* esirisc: support eSi-RISC targets
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* rtos: check symbol list when updating uCOS-III
This patch corrects a crash in uCOS-III on a new GDB connection when
RTOS autodetection is not used. The crash was caused by not checking if
the symbol list had been loaded prior to updating threads.
Change-Id: I64c5133e02fe22fc8d14584cc40d87b49c935b0b
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4719
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* ftdi: demote unhelpful debug messages
Some protocols make use of empty scan fields for optional padding, which
causes the log to fill with unhelpful messages that a field is empty.
The remaining LOG_DEBUG messages in ftdi_execute_scan have been demoted
to DEBUG_JTAG_IO such that these messages are only seen when debugging
JTAG.
Change-Id: I61fd4551411ce851da34e67d003bca5d7a71cd92
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4112
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* tcl: Add support for the Numato Lab Mimas A7 board
The Mimas A7 FPGA board has FTDI FT2232 whose channel B is connected to
Artix-7 FPGA's JTAG interface. Hence, OpenOCD can easily interface with
it via the its ftdi driver interface. Tested to be working great up to
30 MHz.
Change-Id: Ieda015fbc6135bf95ad5a069cbf38650da45911e
Signed-off-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-on: http://openocd.zylin.com/4720
Tested-by: jenkins
Reviewed-by: Tim "mithro" Ansell <me@mith.ro>
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/arm_adi_v5: fix sync CSW cache on apreg write
Commit 0057c71ab6 updates the OpenOCD
cached values of CSW and TAR registers if these registers are modified
by an apreg command.
The condition to force the update of CSW cache is incorrect and it will
erase the default CSW value.
Moreover, calling mem_ap_setup_csw() does not honor the value requested
in the apreg command because such value is incorrectly bitwise or-ed
with csw_default.
Fix it by updating csw_value, instead of erasing csw_default, and writing
directly in CSW register the new value from the command line.
Change-Id: I40273cb64d22ccfb9b6d3499bd39b586eb60de38
Fixes: 0057c71ab6 ("target/arm_adi_v5: sync CSW and TAR cache on apreg write")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4679
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: Add Arty-S7 Spartan 7 FPGA Development Board
Change-Id: I8bfe780cb67a1777d5112a68e8a9781bfe4f2038
Signed-off-by: William D. Jones <wjones@wdj-consulting.com>
Reviewed-on: http://openocd.zylin.com/4525
Reviewed-by: Robert Jordens <jordens@gmail.com>
Tested-by: jenkins
Reviewed-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* xilinx-xc7: Add additional IDCODEs.
Add/detect missing IDCODEs for the Spartan 7 family and Artix 25T
and Artix 12T.
Change-Id: Ib6c83c5592e90df1eb8e715e79b279da9a95f9c6
Signed-off-by: William D. Jones <wjones@wdj-consulting.com>
Reviewed-on: http://openocd.zylin.com/4428
Reviewed-by: Robert Jördens
Tested-by: jenkins
Reviewed-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: fix temporary breakpoint during step
Commit c8926d1457 introduces the
context and hybrid breakpoint types beside existing SW and HW
types. The new field "asid" is non-zero only for these new types.
The commit above did not properly initialize "asid" to 0 for a
temporarily HW breakpoint used during single step. This causes
cortex_a_unset_breakpoint() to identify this breakpoint as of
type "hybrid".
Identified through valgrind error:
Conditional jump or move depends on uninitialised value(s)
Actually valgrind triggers a total of 10 messages about use of
uninitialized variables, but they are all caused by the first
conditional jump bases on "asid != 0".
Fixed by initializing "asid" to 0 in cortex_a_step().
Fixes: c8926d1457 ("cortex_a hybrid & context breakpoints")
Change-Id: Ib674d8457d1e02e10332fd9d73554d13719ef93d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4613
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* zynq_7000: Add zynqpl_program command
This allows for programming the PL part of the Xilinx Zynq 7000
Change-Id: I89e86c0f381951091f6948c46802d17d7f1f3500
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4177
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/target.c: adding keep_alive() to while loop.
Adding the call to keep_alive() to suppress warnings when
running the async flash algorithm. Issue observed when
loading large pieces of code on slower debuggers.
Change-Id: I7660fa05f68ebd7be07b2ca0a55b0f3b6ae718f3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/4686
Tested-by: jenkins
Reviewed-by: Jesse Marroquin
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* drivers/cmsis-dap: speed up sending multiple HID requests
The performance of CMSIS-DAP in long data transfers was improved substantially in
ef02b69b14. But it not as good as some
other USB/MCU based adapters. Using HID and therefore interrupt endpoint
is slower than USB bulk transfer.
CMSIS-DAP adapter implements multiple HID buffer handling and OpenOCD already
reads number of buffers from info command.
This change adds capability to sumbit more than one HID requests before
driver waits for a HID response. This scenario is used for long transfers only.
Results show about double speed on USB FS and ~140% speed on USB HS:
| w/o this change | with multi HIDrq
-----------------------------------------+-----------------+-----------------
Open source CMSIS-DAP, USB FS, adapter_khz 1000
dump_image ram32k.bin 0x1fffe000 0x8000 | 23.225 KiB/s | 45.901 KiB/s
load_image ram32k.bin 0x1fffe000 | 23.324 KiB/s | 46.552 KiB/s
Cypress' Kitprog in CMSIS-DAP mode, USB FS, adapter_khz 1000 (over firmware limit)
dump_image ram64k.bin 0x20000000 0x10000 | 15.537 KiB/s | 42.558 KiB/s
load_image ram64k.bin 0x20000000 | 15.605 KiB/s | 43.291 KiB/s
Atmel's EDBG, USB HS, adapter_khz 10000 (#3945 applied)
dump_image ram384k.bin 0x20400000 0x6000 | 248.402 KiB/s | 345.250 KiB/s
load_image ram384k.bin 0x20400000 | 256.039 KiB/s | 365.945 KiB/s
Change-Id: I9edbe018086176d357c6aaba5d6b657a5e5e1c64
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4080
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl: target: omit apcsw for hla
When using stlink for CM7 targets we have to rely on its firmware
to do the right thing as direct DAP access is not possible.
Change-Id: Ieee69f4eeea5c911f89f060f31ce86ed043bdfd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4732
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/at91samd: add SAMR21E19A DID
While on it correct RAM amount of SAMR21x16A devices
Change-Id: Ie9ab9de1551bdceff17af7597a9a2ee41f5aebe0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4734
Reviewed-by: Eduardo Montoya
Tested-by: jenkins
* arm_adi_v5: do not deactivate power domains while trying to clear sticky error
At OpenOCD start-up the operation of clearing the sticky error in
CTRL/STAT register ignores the current value of the power domains
bits CDBGPWRUPREQ and CSYSPWRUPREQ in the same register and
incorrectly set them to zero.
This abrupt disable does not follow the requirement in IHI0031 to
wait for the acknowledgment of power disabled before continuing.
The power domains are then re-enabled immediately after; it is
possible that such short disable period has passed undetected or
has been tested only on devices that do not implement the power
domains.
Anyway, this sequence is incorrect and can generate unexpected
and hard-to-debug issues while OpenOCD attaches to a running
target that implements power domains.
Anticipate the initialization of dap->dp_ctrl_stat and use it
while clearing the sticky bit. This has the additional effect of
avoiding a power disable in the error recovery part of the
function dap_dp_read_atomic().
Keep the same sequence of read/write in dap_dp_init() to avoid
breaking the initialization of some problematic target.
Add comments to document these choices.
Change-Id: I8d6da788f2dd11909792b5d6b69bc90fbe4df25d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4677
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* flash/nor/stm32f1x: Use of protection blocks, improved option bytes handling
Handle write protection status in blocks instead of sectors, removing
unnecessary complexity in the process. Now closer to stm32f2x.
Support sequential modification of option bytes by read/modify/write
directly to option bytes area instead of always starting with the
currently loaded bytes from FLASH_OBR/WRPR registers.
Added new command 'options_load' to force re-load of option bytes w/o
having to power cycle target.
Change-Id: I5c76191e29c17a1e11482df06379d10ca8d6d04d
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4576
Tested-by: jenkins
Reviewed-by: Jan Vojtěch <honza.vojtech@gmail.com>
* target/cortex_a: remove unused code controlled by "fast_reg_read"
The variable fast_reg_read is always zero, causing some code to
never be executed.
Such code try to read the target registers by dumping them in
memory and then reading back the memory through the debugger. But
it is broken due to lack of cache and MMU management.
This code also uses the broken memory_ap access that is going to
be removed soon.
Remove all the code that depends on fast_reg_read not zero.
Add a missing check on arm_dpm_read_current_registers() return.
Keep the unused function cortex_a_dap_write_coreregister_u32()
to balance the used "read" version.
Change-Id: If2ff28a8c49eb0a87dc85207f5431978efd158db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4746
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: remove buggy memory AP accesses
The armv7m debug port provides a direct access to the CPU memory
bus, allowing the debugger to bypass the CPU for every memory
operation.
The armv7a debug port doesn't offer the same feature, mainly
because CPU caches and MMU makes the direct memory access more
tricky. Nevertheless most SoC with armv7a provide direct memory
access through an AHB bus available on another DAP access port,
different from the debug port.
The original port of cortex_a in OpenOCD was inspired from the
working cortex_m code, and provided optional memory access
through the AHB, if present.
The code for AHB access is problematic and partially buggy due
to incomplete management of cache coherency and missing check of
page boundary during virtual address operations.
With the commit 5d458cf727
("target/mem_ap: generic mem-ap target") we have a clean support
for memory access through system buses connected to DAP AP, which
obsoletes the buggy memory AP hack in cortex_a.
Remove any code that uses the memory AP accesses in cortex_a.
Change-Id: I7cd1f94885e5817448058953e043d8da90dea3cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4748
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/arm_dpm: uniform names of exported functions
The name of the function dpm_modeswitch() does not follow the
common style of the other function names in the same file.
Rename it as arm_dpm_modeswitch().
Change-Id: Idebf3c7bbddcd9b3c7b44f8d0dea1e5f7549b0eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4756
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: remove duplicate code to read target registers
The functions cortex_a_dap_{read,write}_coreregister_u32() are
duplicate of the functions dpm_{read,write}_reg().
Remove both duplicated functions in cortex_a.c while export only
dpm_read_reg(), since dpm_write_reg() is currently not used.
Rename dpm_read_reg() as arm_dpm_read_reg() to keep uniform the
naming style.
Change-Id: I501bc99dc402039e630c47917a086a0bb382782c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4747
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
* armv7a: ARMv7-A MMU tools
factor out mmu-related code from armv7a.c, add a 'dump' command for
page tables.
Change-Id: Ic1ac3c645d7fd097e9d625c7c8302e7065875dd4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag/bitq: array boundary overflow
The for loop inside bitq_path_move function is not correct, this will
overflow the cmd->path array and produces an unpredictable result.
Change-Id: I81e3bc9ee6d1dd948acd2fe4c667103ac22bb26f
Signed-off-by: xuguangxiao <szgxxu@qq.com>
Reviewed-on: http://openocd.zylin.com/4733
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/stm32h7x: Fix documentation of reset_config
The stm32h7x.cfg does not specify connect_assert_srst or
connect_deassert_srst in its reset_config. The comment claims that it
will therefore connect in reset. However, per the manual, the default
configuration is actually connect_deassert_srst, not
connect_assert_srst. In actual fact, connect_assert_srst does not work
on the STM32H7 because, while SRST is asserted, everything on the AXI
bus is inaccessible. The CPU core is accessible, but since the
examine-end event handler also pokes at the DBGMCU peripheral, that will
fail in connect_assert_srst mode. So using connect_deassert_srst is
appropriate, so fix the comment accordingly.
Change-Id: If3e32e871fb19cc61183bdf911b7c5efd80b62e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4741
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* docs: fix typo in manual
Change-Id: I28717105eb2a907b0cb4b03f4b5ff1f47194413b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4751
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* README: fix stlink instructions
Since 31c58c139d there is a unified config
for all stlink versions.
Change-Id: Id736063496ecd96e2024ed69dcb67a22c44b80bb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4672
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Permit null target on TCL connection
In previous versions of OpenOCD, it was possible to connect to the TCL
RPC interface without a current target. In `tcl_new_connection`, the
curent target would be queried by number, and the possibility of a null
current target was handled properly.
In commit bb9d9c6026, the
`get_target_by_num` call was replaced by a `get_current_target` call,
without noticing that `get_current_target` aborts if there is no current
target, whereas `tcl_new_connection` is perfectly able to handle that
situation.
Provide a `get_current_target_or_null` function for use by consumers who
are OK with a null current target, and use it in `tcl_new_connection`.
Change-Id: I06f7e1e149f1169e23c73ba328c7ad9f9425cc2a
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4730
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
* riscv_get_thread_reg_list matches new prototype.
None of the existing test cases cause this function to be called. I
suspect it never gets called, since it is weird to have a function that
only returns the GPRs as a full list of registers.
Change-Id: Ib54f182c1b2fc4dd711c877cb5c9b3e0af77461d
* Fix conflict resolutions.
Change-Id: I5228c308a08ee54530f8c1cadac2afe1c974d41e
S6 record is equivalent to S5 but it uses 24-bit value (instead of 16-bit)
to store total number of data records. It can be found in big srec files
with total number of data records bigger than 65535
Handle S6 record in the same way as S5 (simply ignore it)
Change-Id: I3e15a4e8f784fd38803c00accf422f803e8469cd
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4645
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In previous versions of OpenOCD, it was possible to connect to the TCL
RPC interface without a current target. In `tcl_new_connection`, the
curent target would be queried by number, and the possibility of a null
current target was handled properly.
In commit bb9d9c6026, the
`get_target_by_num` call was replaced by a `get_current_target` call,
without noticing that `get_current_target` aborts if there is no current
target, whereas `tcl_new_connection` is perfectly able to handle that
situation.
Provide a `get_current_target_or_null` function for use by consumers who
are OK with a null current target, and use it in `tcl_new_connection`.
Change-Id: I06f7e1e149f1169e23c73ba328c7ad9f9425cc2a
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4730
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
The functions cortex_a_dap_{read,write}_coreregister_u32() are
duplicate of the functions dpm_{read,write}_reg().
Remove both duplicated functions in cortex_a.c while export only
dpm_read_reg(), since dpm_write_reg() is currently not used.
Rename dpm_read_reg() as arm_dpm_read_reg() to keep uniform the
naming style.
Change-Id: I501bc99dc402039e630c47917a086a0bb382782c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4747
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
The name of the function dpm_modeswitch() does not follow the
common style of the other function names in the same file.
Rename it as arm_dpm_modeswitch().
Change-Id: Idebf3c7bbddcd9b3c7b44f8d0dea1e5f7549b0eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4756
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The armv7m debug port provides a direct access to the CPU memory
bus, allowing the debugger to bypass the CPU for every memory
operation.
The armv7a debug port doesn't offer the same feature, mainly
because CPU caches and MMU makes the direct memory access more
tricky. Nevertheless most SoC with armv7a provide direct memory
access through an AHB bus available on another DAP access port,
different from the debug port.
The original port of cortex_a in OpenOCD was inspired from the
working cortex_m code, and provided optional memory access
through the AHB, if present.
The code for AHB access is problematic and partially buggy due
to incomplete management of cache coherency and missing check of
page boundary during virtual address operations.
With the commit 5d458cf727
("target/mem_ap: generic mem-ap target") we have a clean support
for memory access through system buses connected to DAP AP, which
obsoletes the buggy memory AP hack in cortex_a.
Remove any code that uses the memory AP accesses in cortex_a.
Change-Id: I7cd1f94885e5817448058953e043d8da90dea3cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4748
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The variable fast_reg_read is always zero, causing some code to
never be executed.
Such code try to read the target registers by dumping them in
memory and then reading back the memory through the debugger. But
it is broken due to lack of cache and MMU management.
This code also uses the broken memory_ap access that is going to
be removed soon.
Remove all the code that depends on fast_reg_read not zero.
Add a missing check on arm_dpm_read_current_registers() return.
Keep the unused function cortex_a_dap_write_coreregister_u32()
to balance the used "read" version.
Change-Id: If2ff28a8c49eb0a87dc85207f5431978efd158db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4746
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Install patchutils for the build.
This contains filterdiff, which we need to check that our changes
conform to OpenOCD style.
Change-Id: Id522f4e62fee3efad4e0e00933abfeada9635624
* Fix paths for filterdiff line.
Change-Id: Ic50e13c7fe64e65b2d2af0260fb19c07a9f10e20
* Conform to OpenOCD style.
Change-Id: I51660d30404c0a625b58c9bed2d948695575e72e
This fixes the following error, that has been reported occasionally:
Error: 34072 2712 riscv-011.c:1175 reg_cache_get(): Register cache entry for 0 is invalid!
openocd: ../src/target/riscv/riscv-011.c:1176: reg_cache_get: Assertion `r->valid' failed.
The problem was that we'd tell the target to step, and then gdb (which
assumed the target halted already) asked to read a register before the
target had actually halted. With this fix the target is actually halted,
and everything works.
Change-Id: Icfcef456f3cec4bb352fb90186f5bbabb00a5ff8
At OpenOCD start-up the operation of clearing the sticky error in
CTRL/STAT register ignores the current value of the power domains
bits CDBGPWRUPREQ and CSYSPWRUPREQ in the same register and
incorrectly set them to zero.
This abrupt disable does not follow the requirement in IHI0031 to
wait for the acknowledgment of power disabled before continuing.
The power domains are then re-enabled immediately after; it is
possible that such short disable period has passed undetected or
has been tested only on devices that do not implement the power
domains.
Anyway, this sequence is incorrect and can generate unexpected
and hard-to-debug issues while OpenOCD attaches to a running
target that implements power domains.
Anticipate the initialization of dap->dp_ctrl_stat and use it
while clearing the sticky bit. This has the additional effect of
avoiding a power disable in the error recovery part of the
function dap_dp_read_atomic().
Keep the same sequence of read/write in dap_dp_init() to avoid
breaking the initialization of some problematic target.
Add comments to document these choices.
Change-Id: I8d6da788f2dd11909792b5d6b69bc90fbe4df25d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4677
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Changed logging level
* Added logging statement
* Removed halt event when attaching to target
* Extended some packet handling
* Extended handling of rtos_hart_id and clearing of register cache
* Extended execute_fence to handle all harts
* Removing logging statement again
* Updated according to review comments
* Forgot to re-add the return statement
* Was removing too much for the if statement to work
* This needs to >= 3 now to handle both a fence and a fence.i
Adding the call to keep_alive() to suppress warnings when
running the async flash algorithm. Issue observed when
loading large pieces of code on slower debuggers.
Change-Id: I7660fa05f68ebd7be07b2ca0a55b0f3b6ae718f3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/4686
Tested-by: jenkins
Reviewed-by: Jesse Marroquin
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c8926d1457 introduces the
context and hybrid breakpoint types beside existing SW and HW
types. The new field "asid" is non-zero only for these new types.
The commit above did not properly initialize "asid" to 0 for a
temporarily HW breakpoint used during single step. This causes
cortex_a_unset_breakpoint() to identify this breakpoint as of
type "hybrid".
Identified through valgrind error:
Conditional jump or move depends on uninitialised value(s)
Actually valgrind triggers a total of 10 messages about use of
uninitialized variables, but they are all caused by the first
conditional jump bases on "asid != 0".
Fixed by initializing "asid" to 0 in cortex_a_step().
Fixes: c8926d1457 ("cortex_a hybrid & context breakpoints")
Change-Id: Ib674d8457d1e02e10332fd9d73554d13719ef93d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4613
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Commit 0057c71ab6 updates the OpenOCD
cached values of CSW and TAR registers if these registers are modified
by an apreg command.
The condition to force the update of CSW cache is incorrect and it will
erase the default CSW value.
Moreover, calling mem_ap_setup_csw() does not honor the value requested
in the apreg command because such value is incorrectly bitwise or-ed
with csw_default.
Fix it by updating csw_value, instead of erasing csw_default, and writing
directly in CSW register the new value from the command line.
Change-Id: I40273cb64d22ccfb9b6d3499bd39b586eb60de38
Fixes: 0057c71ab6 ("target/arm_adi_v5: sync CSW and TAR cache on apreg write")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4679
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This change adds optional support for a target to report architecture
information in the target description to GDB. This is needed by some GDB
implementations to properly support remote target with custom behavior.
More information on the architecture element can be found here:
https://sourceware.org/gdb/onlinedocs/gdb/Target-Description-Format.html#Target-Description-Format
Change-Id: I57b19cae5ac3496256e4e5cc52cf6526ca5c322d
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4078
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch fixes a number of bugs caused by incomplete support for
non-existent registers. This is needed for targets that provide optional
registers or non-linear register numbers.
Change-Id: I216196e0051f28887a2c3da410959382369eed80
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4113
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Virtual targets, like mem_ap, do not or cannot implement the required
functionality to accept a GDB connection. In the case of mem_ap, the
method get_gdb_reg_list() is missing and a following connection from
gdb causes OpenOCD to segfault.
OpenOCD opens a GDB port for each target; it's always possible to
connect, by mistake, GDB to one virtual target.
Add a method to check if the target supports GDB connections (for the
moment just checking if get_gdb_reg_list is implemented).
Skip opening a gdb server for every targets that don't support GDB
connections.
Change-Id: Ia439a43efe1a9adbb1771cd9d252db8ffa32eb9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4676
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The subunit of the debug unit is called the Flash Patch and Breakpoint
unit, abbreviated (by ARM no less) as FPB, not FBP.
Change-Id: Ia2f08470da705f0f1518feeca878f0f500507308
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4675
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The field ap_num in struct adiv5_private_config is already of type int.
Casting it to type int has no sense.
Change-Id: Ida642e808c02591bb58609425eccd096d404e2c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4666
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The periodic poll scans all the targets in the same order they
have been declared in the configuration file.
When one target in a SMP node halts, the transition is detected
in the following poll and this triggers a halt request to all the
other cores of the SMP node.
The targets that will be polled afterwards will be identified as
"halted", but the targets already scanned will remain as
"running" until the next periodic poll.
This creates a race condition with GDB; GDB sets the breakpoints
when runs the target and removes them as soon as the target is
halted. When it receives the halt event, it starts removing the
breakpoints and fails on the targets that are still reported as
"running".
Fixed by polling all the targets in the SMP node before informing
GDB about the halt event.
This implementation is almost copy/paste from the one in aarch64.
Change-Id: Id2bd99f1e56b014e48e9e34ccb891b4219c518f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4622
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This pseudo target allows attaching to any access point on the DAP at the
MEM-AP level and read and write addresses on the connected bus. For
example, one can create a mem_ap target on the APB-AP and read and write
registers of debug components directly. This allows many diagnostic
and other features be programmed entirely using TCL, without necessity
of adding drivers to OpenOCD.
Change-Id: I53229ffd68fb0f96fb68be15b0f3a76cc8843c8e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4002
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Leonard Crestez <cdleonard@gmail.com>
The argument passed to global config command "gdb_port" is usually,
but not always, a TCP port number. In case of multiple targets, this
numeric value is used as the first port of a set of consecutive TCP
ports assigned one per target.
If the argument is not a numeric value (e.g. "pipe", "disabled", ...)
then incrementing it for the next target has no sense.
Add the option "-gdb-port number" to the commands "target create" and
"$target_name configure" to override, for the specific target, the
general global configuration.
This permits to use a per target "-gdb-port disabled", when no gdb
port is required for that specific target.
It also makes possible to choose a custom TCP port number for each
target, overriding the usual sequence of consecutive port numbers.
Change-Id: I3b9a1910b28ab4bc757e839d0e5d08ffc29f7ab4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4530
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The AP number value is restricted in 8 bits unsigned by ADI-v5
specification. Nevertheless, an "invalid" value is used by
target cortex-m to force an automatic detection of the AP.
Replace magic numbers by using new macros for AP max number and
for the value of AP invalid.
Check the value passed through -ap-num flag during configuration.
Change-Id: Ic19a367db0ab11c0ebd070750eca0647d25279a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4668
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Added `riscv expose_custom` command.
Seems to work for reading. I need to do some more testing for writes, as
well as minor cleanup.
Change-Id: I85d5d00897d5da4add4a6643b538be37d31a016f
* Conform to OpenOCD style.
Change-Id: I40a316f06f418d2b63d9e11aea03ef51da8d8faf
* Free all the memory allocated by register init.
Change-Id: I04e35ab54613f99708cee85e41fef989079adefc
* Properly document `riscv expose_custom`.
Change-Id: Id78a02b7a00c161df80f11b521a306e0cf3d7478
* Add riscv_hit_watchpoint function for RV32I loads and stores
For GDB to fully support hardware watchpoints, OpenOCD needs to tell GDB
which data address has been hit. OpenOCD relies on a target-specific
hit_watchpoint function to do this. If GDB is not given the address, it
will not print the hit variable name or its old and new value.
There does not seem to be a way for the hardware to tell us which trigger
was hit (0.13 introduced the 'hit bit' but this is optional). Alternatively,
we can decode the instruction at dpc and find out which memory address
it accesses.
This commit adds support for RV32I load and store instructions
and could be extended for additional instructions in the future.
* 0.11: change debug reason for hw triggers to DBG_REASON_WATCHPOINT
This is to make sure riscv_hit_watchpoint is called to check for a data
address hit.
* Fix style issues
* Change %lx to PRIx64 to clear -m32 build errors
* Add clarifying comments/todos
* Fix types in format strings
* flash/nor: Add support for TI CC26xx/CC13xx flash
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
* flash/nor/nrf5: remove is_erased setting and autoerase before write
Cached flash erase state in sectors[].is_erased is not reliable as running
target can change the flash.
Autoerase was issued before flash write on condition is_erased != 1
Remove autoerase completely as it is a quite non-standard feature.
Change-Id: I19bef459e6afdc4c5fcaa2ccd194cf05be8a42b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4400
Tested-by: jenkins
* src/flash/tms470: remove testing of sectors[].is_erased state
The erase check routine checked sectors only if is_erased != 1
Check sector unconditionally.
While on it fix clang static analyzer warnings.
Change-Id: I9988615fd8530c55a9b0c54b1900f89b550345e9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4401
Tested-by: jenkins
* tcl/target/stm32f7x: configure faster system clock in reset-init
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/psoc5lp: fix compile issue on GCC 8.1.0
Issue already identified by Alex https://sourceforge.net/u/alexbour/
in ticket #191https://sourceforge.net/p/openocd/tickets/191/
src/flash/nor/psoc5lp.c:237:2: error: ‘strncpy’ output
truncated before terminating nul copying 2 bytes from a
string of the same length [-Werror=stringop-truncation]
Fix it by assigning the value to the array elements.
Change-Id: I22468e5700efa64ea48ae8cdec930c48b4a7d8fb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4563
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm: Add PLD command to ARM disassembler.
Updates the ARM disassembler to handle PLD (PreLoad Data) commands.
Previously handled by printing a TODO message. There are three forms of
the command: literal, register, and immediate. Simply decode based off
of the A1 encoding for the instructions in the ARM ARM. Also fixes mask
to handle PLDW commands.
Change-Id: I63bf97f16af254e838462c7cfac80f6c4681c556
Signed-off-by: James Marshall <jcmarsh@gwmail.gwu.edu>
Reviewed-on: http://openocd.zylin.com/4348
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* mips_m4k.c: Fix build with --disable-target64
Replace PRIx64 with TARGET_PRIxADDR to avoid build problems
when --disable-target64 is used during configure.
Change-Id: I054a27a491e86c42c9386a0488194320b808ba96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4566
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/arm_adi_v5: sync CSW and TAR cache on apreg write
When using apreg to change AP registers CSW or TAR we get internal
cached value not valid anymore.
Reuse the setup functions for CSW and TAR to write them.
Invalidate the cached value before the call to force the write, thus
keeping original apreg behaviour.
Change-Id: Ib14fafd5e584345de94f2e983de55406c588ac1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4565
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: keep CSW and TAR cache updated
The call to dap_queue_ap_write() can fail and the value in CSW and
TAR becomes unknown.
Invalidate the OpenOCD cache if dap_queue_ap_write() fails.
Change-Id: Id6ec370b4c5ad07e454464780c1a1c8ae34ac870
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4564
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target: Add Renesas R-Car R8A7794 E2 target
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7790 H2 Stout board
Add configuration for the Renesas R-Car R8A7790 H2
based Stout ADAS board.
Change-Id: Ib880b5d2e1fab5c8c0bc0dbcedcdce8055463fe2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4497
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7791 M2W Porter board
Add configuration for the Renesas R-Car R8A7791 M2W
based Porter evaluation board.
Change-Id: Iaadb18f29748f890ebb68519ea9ddbd18e7649af
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4498
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Add Renesas R-Car R8A7794 E2 Silk board
Add configuration for the Renesas R-Car R8A7794 E2
based Silk evaluation board.
Change-Id: I504b5630b1a2791ed6967c6c2af8851ceef9723f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
NOTE: This requires SW7[1] in position 1 (default is 0)
Reviewed-on: http://openocd.zylin.com/4532
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/board: Factor out common R-Car Gen2 code
Factor out the code shared by all R-Car Gen2 boards into a single
file to get rid of the duplication.
Change-Id: I70b302c2e71f4e6fdccb2817dd65a5493bb393d8
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4533
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* jtag/drivers/cmsis-dap: fix connect in cmsis_dap_swd_switch_seq()
The proc cmsis_dap_swd_switch_seq() is part of the SWD API for
this interface driver. It is valid only when the interface is
used in SWD mode.
In this proc there is the need to call, in sequence, first
cmsis_dap_cmd_DAP_Disconnect() then cmsis_dap_cmd_DAP_Connect().
The latter call requires the connection mode as parameter, that
inside cmsis_dap_swd_switch_seq() can only be CONNECT_SWD.
The current implementation is not correct and in some cases can
pass mode CONNECT_JTAG. Moreover, JTAG is optional in CMSIS-DAP
and passing mode CONNECT_JTAG triggers an error with SWD-only
interfaces.
Use mode CONNECT_SWD in SWD specific cmsis_dap_swd_switch_seq().
Change-Id: Ib455bf5b69cb2a2d146a6c8875387b00c27a5690
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4571
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: return error if breakpoint address is out of range
If the "Flash Patch and Breakpoint" unit is rev.1 then it can only
accept breakpoint addresses below 0x1FFFFFFF.
Detailed info in "ARM v7-M Architecture Reference Manual", DDI0403E
at chapter "C1.11 Flash Patch and Breakpoint unit".
Print a message and return error if the address of hardware
breakpoint cannot be handled by the breakpoint unit.
Change-Id: I95c92b1f058f0dfc568bf03015f99e439b27c59b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4535
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* flash/nor/stm32: Report errors in wait_status_busy
Flash operation errors that occur during algorithm programming are
reported via the algorithm return value. However, Flash operation
errors that occur during non-algorithm work (erasing, programming
without a work area, programming the last non-multiple-of-32-bytes on
an H7, etc.) generally end with a call to stm32x_wait_status_busy,
which reads the status register and clears the error flags but fails
to actually report that something went wrong should an error flag
(other than WRPERR) be set. Return an error status from
stm32x_wait_status_busy in those cases. Correct a log message
accordingly.
Change-Id: I09369ea5f924fe58833aec1f45e52320ab4aaf43
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4519
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32: Eliminate working area leak
On a specific early-return path, an allocated working area was not
freed. Free it.
Change-Id: I7c8fe51ff475f191624086996be1c77251780b77
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4520
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/stm32h7: Fix incorrect comment
The name of the bit according to the reference manual is inconsistency
error, not increment error.
Change-Id: Ie3b73c0312db586e35519e03fd1a5cb225673d97
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4521
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* target: fix 'bp' command help message
"asid" and "length" are separate arguments of the command.
Put space between them.
Change-Id: I36cfc1e3a01caafef4fc3b26972a0cc192b0b963
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4511
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Add ARM v8 AArch64 semihosting support
This patch implements semihosting support for AArch64. This picks
code from previously submitted AArch64 semihosting support patch
and rebases on top of reworked semihosting code. Tested in AArch64
mode on a Lemaker Hikey Board with NewLib and GDB.
Change-Id: I228a38f1de24f79e49ba99d8514d822a28c2950b
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4537
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* GDB fileIO stdout support
This patch fixes gdb fileio support to allow gdb console to be used as stdout.
Now we can do something like
gdb <inferior file>
(gdb) tar ext :3333
(gdb) load
(gdb) monitor arm semihosting enable
(gdb) monitor arm semihosting_fileio enable
(gdb) continue
Here: Output from inferior using puts, printf etc will be routed to gdb console.
Change-Id: I9cb0dddda1de58038c84f5b035c38229828cd744
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4538
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target: armv8: Avoid semihosting segfault on halt
Avoid a NULL pointer dereference when halting an aarch64 core.
Change-Id: I333d40475ab26e2f0dca5c27302a5fa4d817a12f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4593
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: target: Add NXP LS1012A config
As seen on the FRDM-LS1012A board.
Change-Id: Ifc9074b3f7535167b9ded5f544501ec2879f5db7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4594
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl: board: Add NXP Freedom FRDM-LS1012A config
An update for the K20 CMSIS-DAP firmware can be found here:
https://community.nxp.com/thread/387080?commentID=840141#comment-840141
Change-Id: I149d7f8610aa56daf1aeb95f14ee1bf88f7cb647
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4595
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* gdb_server: only trigger once the event gdb-detach at gdb quit
When GDB quits (e.g. with "quit" command) we first execute
gdb_detach() to reply "OK" then, at GDB disconnect (either TCP
or pipe connection type), we execute gdb_connection_closed().
In case GDB is killed or it crashes, OpenOCD only executes the
latter when detects the disconnection.
Both gdb_detach() and gdb_connection_closed() trigger the event
TARGET_EVENT_GDB_DETACH thus getting it triggered twice on clean
GDB quit.
Do not trigger the event TARGET_EVENT_GDB_DETACH in gdb_detach()
and let only gdb_connection_closed() to handle it.
Change-Id: Iacf035c855b8b3e2239c1c0e259c279688b418ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4585
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* gdb_server: set current_target from connection's one
In a multi-target environment we are supposed to have a single
gdb server for each target (or for each group of targets within
a SMP node).
By default, the gdb attached to a server sends its command to
the target (or to the SMP node targets) linked to that server.
This is working fine for the normal gdb commands, but it is
broken for the native OpenOCD commands executed through gdb
"monitor" command. In the latter case, gdb "monitor" commands
will be executed on the current target of OpenOCD configuration
script (that is either the last target created or the target
specified in a "targets" command).
Fixed in gdb_new_connection() by replacing the current target
in the connection's copy of command context.
Change-Id: If7c8f2dce4a3138f0907d3000dd0b15e670cfa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4586
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/image: make i/j unsigned to avoid ubsan runtime error
src/target/image.c:1055:15: runtime error: left shift of 128 by 24 places cannot be represented in type 'int'
Change-Id: I322fd391cf3f242beffc8a274824763c8c5e69a4
Signed-off-by: Cody Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4584
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/stm32f7x: Clear stuck HSE clock with CSS
Change-Id: Ica0025ea465910dd664ab546b66f4f25b271f1f5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4570
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* psoc5lp: fix erase check, add free_driver_priv
psoc5lp_erase_check() was not properly adapted to the new
armv7m_blank_check_memory() in the hot fix 53376dbbed
This change fixes handling of num_sectors in dependecy of ecc_enabled.
Also add comments how ecc_enabled influences num_sectors.
Add pointer to default_flash_free_driver_priv() to all psoc5lp flash
drivers to keep valgrind happy.
Change-Id: Ie1806538becd364fe0efb7a414f0fe6a84b2055b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4569
Tested-by: jenkins
* target: atmel samd10 xplained mini
cortex m0+ on a tiny board, with an mEDBG (CMSIS-DAP) debug interface.
Change-Id: Iaedfab578b4eb4aa2d923bd80f220f59b34e6ef9
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: add SAMD11 Xplained Pro evaluation board
Change-Id: Id996c4de6dc9f25f71424017bf07689fea7bd3af
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4507
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Adds SAMD11D14AU flash support.
Corrects names of SAMD11D14AM and SAMD11D14ASS per datasheet.
Change-Id: I8beb15d5376966a4f8d7de76bfb2cbda2db440dc
Signed-off-by: Christopher Hoover <ch@murgatroid.com>
Reviewed-on: http://openocd.zylin.com/4597
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nds32: Avoid detected JTAG clock
AICE2 doesn't support scan for the maximum clock frequency of
JTAG chain. It will cause USB command timeout.
Change-Id: I41d1e3be387b6ed5a4dd0be663385a5f053fbcf9
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/4292
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl: Distinguish between sectors and blocks in status messages
Use the right word in flash protect command status messages based on
whether the target bank defines num_prot_blocks. Minor message style
tidy-up.
Change-Id: I5f40fb5627422536ce737f242fbf80feafe7a1fc
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4573
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* drivers: cmsis-dap: pull up common connect code
Just a minor deduplication
Change-Id: Idd256883e5f6d4bd4dcc18462dd5468991f507b3
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* drivers: cmsis-dap: Print version info when available
No need to wait until after connecting, might help diagnose part information by
printing earlier.
Change-Id: I51eb0d584be306baa811fbeb1ad6a604773e602c
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3404
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor: add support for TI MSP432 devices
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/at91sam4: fix sam4sa16c flash banks and its gpnvms count
There was already a github fork that had this fixed, but as we try
to use the latest, non-modified version of all software we use,
I would like to have this fix in the next releases of OpenOCD so
that if people uses $packagemanager, they will not have issues flashing
the last part of the flash of sam4sa16c chips.
Additionally, I've added some more logging related to the flash
bank that was used, and the chip ID that was detected.
Change-Id: I7ea5970105906e4560b727e46222ae9a91e41559
Signed-off-by: Erwin Oegema <blablaechthema@hotmail.com>
Reviewed-on: http://openocd.zylin.com/4599
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* flash/nor/stm32lx: Add revision 'V' for STM32L1xx Cat.3 devices
Change-Id: Ic92b0fb5b738af3bec79ae335876aa9e26f5f4cd
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4600
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid null target->semihosting references.
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: Add HWID 0x139 (52832 rev E0)
Change-Id: I71b7471ccfcb8fcc6de30da57ce4165c7fb1f73f
Signed-off-by: James Jacobsson <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4604
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target: Fix segfault for 'mem2array'
Call 'mem2array' without arguments to reproduce the segmentation
fault.
Change-Id: I02bf46cc8bd317abbb721a8c75d7cbfac99eb34e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4534
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
* target/armv7m_trace: Fix typo in enum
Change-Id: I6364ee5011ef2d55c59674e3b97504a285de0cb2
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3904
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/armv7m_trace: Use prefix for enums
Change-Id: I3f199e6053146a1094d96b98ea174b41bb021599
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3905
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/aarch64: Call aarch64_init_debug_access() earlier in aarch64_deassert_reset()
On Renesas R-Car, calling 'reset halt' and 'reset init' always made DAP inaccessible. Calling 'reset' and 'halt' seperatly worked fine.
The only differences seems to be the point in time when aarch64_init_debug_access() is called. This patch aligns the behaviour.
Change-Id: I2296c65e48414a7d9846f12a395e5eca315b49ca
Signed-off-by: Dennis Ostermann <dennis.ostermann@renesas.com>
Reviewed-on: http://openocd.zylin.com/4607
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* server: Improve signal handling under Linux
Commit 5087a955 added custom signal handlers for the openocd
server process.
Before this commit, when openocd is run as a background process
having the same controlling terminal as gdb, Control-C would be
handled by gdb to stop target execution and return to the gdb prompt.
However, after commit 5087a955, the SIGINT caused by pressing
Control-C also terminates openocd, effectively crashing the
debugging session. The only way to avoid this is run openocd in
a different controling terminal or to detach openocd from its
controlling terminal,
thus losing all job control for the openocd process.
This patch improves the server's handling of POSIX signals:
1) Keyboard generated signals (INT and QUIT) are ignored
when server process has is no controlling terminal.
2) SIGHUP and SIGPIPE are handled to ensure that .quit functions
for each interface are called if user's logs out of X
session or there is a network failure.
SIG_INT & SIG_QUIT still stop openocd
when it is running in the foreground.
Change-Id: I03ad645e62408fdaf4edc49a3550b89b287eda10
Signed-off-by: Brent Roman <genosensor@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3963
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* armv7a: read ttbcr and ttb0/1 at every entry in debug state
Commit bfc5c764df avoids reading
ttbcr and ttb0/1 at every virt2phys translation by caching them,
and it updates the cached values in armv7a_arch_state().
But the purpose of any (*arch_state)() method, thus including
armv7a_arch_state(), is to only print out and inform the user
about some architecture specific status.
Moreover, to reduce the verbosity during a GDB session, the
method (*arch_state)() is not executed anymore at debug state
entry (check use of target->verbose_halt_msg in src/openocd.c),
thus the state of translation table gets out-of-sync triggering
Error: Address translation failure
or even using a wrong address in the memory R/W operation.
In addition, the commit above breaks the case of armv7r by
calling armv7a_read_ttbcr() unconditionally.
Fixed by moving in cortex_a_post_debug_entry() the call to
armv7a_read_ttbcr() on armv7a case only.
Remove the call to armv7a_read_ttbcr() in armv7a_identify_cache()
since it is (conditionally) called only in the same procedure
cortex_a_post_debug_entry().
Fixes: bfc5c764df ("armv7a: cache ttbcr and ttb0/1 on debug
state entry")
Change-Id: Ifc20eca190111832e339a01b7f85d28c1547c8ba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4601
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Avoid dereferencing NULL pointer.
If a NULL pointer is passed, don't attempt to increment it. This avoids
passing the now not-NULL pointer on and eventually segfaulting. Also
remove some unnecessary temporary variables.
Change-Id: I268e225121aa283d59179bfae407ebf6959d3a4e
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4550
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* Remove FSF mailing address.
Checkpatch complains about this (FSF_MAILING_ADDRESS).
Change-Id: Ib46a7704f9aed4ed16ce7733d43c58254a094149
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* drivers: cmsis_dap_usb: implement cmd JTAG_TMS
Simply add a wrapper around cmsis_dap_cmd_DAP_SWJ_Sequence()
Change-Id: Icf86f84b24e9fec56e2f9e155396aac34b0e06d2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4517
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* arm_adi_v5: put SWJ-DP back to JTAG mode at exit
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add RISC-V support.
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* usb_blaster: Don't unnecessarily go through DR-/IR-Pause
There is no need to pass through DR-/IR-Pause after a scan if we want to
go to DR-/IR-Update. We just have to skip the first step of the path to
the end state because we already did that step when shifting the last
bit.
v2:
- Fix comments as remarked in review of v1
Change-Id: I3c10f02794b2233f63d2150934e2768430873caa
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/4245
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* cortex_a: fix virt2phys when mmu is disabled
When the MMU is not enabled on debug state entry, virt2phys cannot
perform a translation since it is unknown whether a valid MMU
configuration existed before. In this case, return the virtual
address as physical address.
Change-Id: I6f85a7a5dbc200be1a4b5badf10a1a717f1c79c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4480
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* drivers: cmsis-dap: print serial if available
Helpful for sanity checking connections
Change-Id: Ife0d8b4e12d4c03685aac8115c9739a4c1e994fe
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3405
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: make a variable local
The vec_ids variable is not referenced anywhere other than the vector
catch command handler. Make it local to that function.
Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4606
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: fix compile error for uninitialized variable
Commit ad6c71e151 introduced the
variable "mmu_enabled" whose pointer is passed to cortex_a_mmu()
that initialises it.
This initialization is not visible to the compiler that issue
a compile error.
The same situation is common across the same file and the usual
workaround is to initialize it to zero; thus the same fix i
applied here.
Ticket: https://sourceforge.net/p/openocd/tickets/197/
Fixes: commit ad6c71e151 ("cortex_a: fix virt2phys when mmu is disabled")
Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4619
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* mips_m4k: add optional reset handler
In some cases by using SRST we can't halt CPU early enough. And
option PrRst is not available too. In this case the only way is
to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself.
For example by writing to some reset register.
This patch is providing possibility to use user defined reset-assert
handler which will be enabled only in case SRST is disabled. It is
needed to be able switch between two different reset variants on run
time.
Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4404
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target: add config for Qualcomm QCA4531
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable
Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4405
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add config for 8devices LIMA board
More information about this board can be found here:
https://www.8devices.com/products/lima
Change-Id: Id35a35d3e986630d58d37b47828870afd107cc6a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4406
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target|board: move common AR9331 code to atheros_ar9331.cfg
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add DDR2 helper
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/target/atheros_ar9331: add documentation and extra helpers
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* tcl/board: add DPTechnics DPT-Board-v1
it is Atheros AR9331 based IoT dev board.
Change-Id: I6fc3cdea1bef49c53045018ff5acfec4d5610ba6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4424
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* fpga/altera-10m50: add all device id
add all currently know Intel (Alter) MAX 10 device ids
Change-Id: I6a88fef222c8e206812499d41be863c3d89fa944
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4598
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target|board: Add Intel (Altera) Arria 10 target and related board
Target information about this SoC can be found here:
https://www.altera.com/products/fpga/arria-series/arria-10/overview.html
Achilles Instant-Development Kit Arria 10 SoC SoM:
https://www.reflexces.com/products-solutions/development-kits/arria-10/achilles-instant-development-kit-arria-10-soc-som
Change-Id: Id78c741be6a8b7d3a70f37d41088e47ee61b437a
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4583
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/riscv: fix compile error with gcc 8.1.1
Fix compile error:
src/target/riscv/riscv-011.c: In function ‘slot_offset’:
src/target/riscv/riscv-011.c:238:4: error: this statement may fall through
[-Werror=implicit-fallthrough=]
switch (slot) {
^~~~~~
src/target/riscv/riscv-011.c:243:3: note: here
case 64:
^~~~
Fixes: a51ab8ddf6 ("Add RISC-V support.")
Change-Id: I7fa86b305bd90cc590fd4359c3698632d44712e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4618
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* server: explicitly call "shutdown" when catch CTRL-C or a signal
Every TCL command can be renamed (or deleted) and then replaced by
a TCL proc that has the same name of the original TCL command.
This can be used either to completely replace an existing command
or to wrap the original command to extend its functionality.
This applies also to the OpenOCD command "shutdown" and can be
useful, for example, to set back some default value to the target
before quitting OpenOCD.
E.g. (TCL code):
rename shutdown original_shutdown
proc shutdown {} {
puts "This is my implementation of shutdown"
# my own stuff before exit OpenOCD
original_shutdown
}
Unfortunately, sending a signal (or pressing CTRL-C) to terminate
OpenOCD doesn't trigger calling the original "shutdown" command
nor its (eventual) replacement.
Detect if the main loop is terminated by an external signal and
in such case execute explicitly the command "shutdown".
Replace with enum the magic numbers assumed by "shutdown_openocd".
Please notice that it's possible to write a custom "shutdown" TCL
proc that does not call the original "shutdown" command. This is
useful, for example, to prevent the user to quit OpenOCD by typing
"shutdown" in the telnet session.
Such case will not prevent OpenOCD to terminate when receiving a
signal; OpenOCD will quit after executing the custom "shutdown"
command.
Change-Id: I86b8f9eab8dbd7a28dad58b8cafd97caa7a82f43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4551
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* zy1000: fix compile error with gcc 8.1.1
The fall-through comment is not taken in consideration by gcc 8.1.1
because it is inside the braces of a C-code block.
Move the comment outside the C block.
Change-Id: I22d87b2dee109fb8bcf2071ac55fdf7171ffcf4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4614
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* flash/nor/tcl.c: fix flash bank bounds check in 'flash fill' command handler
Steps to reproduce ( STM32F103 'Blue Pill', 128KiB of flash ):
> flash fillh 0x0801FFFE 00 1
wrote 2 bytes to 0x0801fffe in 0.019088s (0.102 KiB/s)
> flash fillw 0x0801FFFE 00 1
Error: stm32f1x.cpu -- clearing lockup after double fault
Error: error waiting for target flash write algorithm
Error: error writing to flash at address 0x08000000 at offset 0x0001fffe
Change-Id: I145092ec5e45bc586b3df48bf37c38c9226915c1
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4516
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/arm_adi_v5: add command "dpreg"
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.
Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
$dap_name dpreg reg [value]
Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* nrf5: add free_driver_priv
Change-Id: I429a9868deb0c4b51f47a4bbad844bdc348e8d21
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/4608
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: add support for NuttX
This patch introduces RTOS support for NuttX. Currently,
only ARM Cortex-M (both FPU and FPU-less) targets are supported.
To use, add the following lines to ~/.gdbinit.
define hookpost-file
eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end
And please make sure the above values are the same as in
src/rtos/nuttx_header.h
Change-Id: I2aaf8644d24dfb84b500516a9685382d5d8fe48f
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Signed-off-by: Masatoshi Tateishi <Masatoshi.Tateishi@jp.sony.com>
Signed-off-by: Nobuto Kobayashi <Nobuto.Kobayashi@sony.com>
Reviewed-on: http://openocd.zylin.com/4103
Tested-by: jenkins
Reviewed-by: Alan Carvalho de Assis <acassis@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* server/server: Add ability to remove services
Add the ability to remove services while OpenOCD is running.
Change-Id: I4067916fda6d03485463fa40901b40484d94e24e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4054
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: fix incorrect comment
The code sets C_MASKINTS if that bit is not already set (correctly). Fix
the comment to agree.
Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4620
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/target/stm32f0x: Allow overriding the Flash bank size
Copy & paste from another stm32 target.
Change-Id: I0f6cbcec974ce70c23c1850526354106caee1172
Signed-off-by: Dominik Peklo <dom.peklo@gmail.com>
Reviewed-on: http://openocd.zylin.com/4575
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* tcl/target: add Allwinner V3s SoC support
Change-Id: I2459d2b137050985b7301047f9651951d72d9e9e
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4427
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* target/arm_adi_v5: allow commands apsel and apcsw during init phase
The current implementation of apsel cannot be executed during the
initialization phase because it queries the DAP AP to retrieve and
print the content of IDR register, and the query is only possible
later on during the exec phase.
But IDR information is already printed by the dedicated command
apid, making redundant printing it by apsel too.
Being unable to run apsel during initialization, makes also apcsw
command (that depends on apsel) not usable in such phase.
Modify the command apsel to only set the current AP, without making
any transfer to the (possibly not initialized yet) DAP. When run
without parameters, just print the current AP number.
Change mode to COMMAND_ANY to apsel and to apcsw.
Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4624
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_a: allow command dacrfixup during init phase
There is no reason to restrict the command "cortex_a dacrfixup"
to the EXEC phase only.
Change the command mode to ANY so the command can be used in
the initialization phase too.
Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4623
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/armv7a_cache: add gdb keep-alive and fix a missing dpm finish
Depending on range size, the loop on cache operations can take quite
some time, causing gdb to timeout.
Add keep-alive to prevent gdb to timeout.
Add also a missing dpm->finish() to balance dpm->prepare().
Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4627
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Add detail to `wrong register size` error.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Id31499c94b539969970251145e42c89c943fd87c
Reviewed-on: http://openocd.zylin.com/4577
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* doc: fix typo in cortex_m maskisr command
Change-Id: I37795c320ff7cbf6f2c7434e03b26dbaf6fc6db4
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4621
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/cortex_m: restore C_MASKINTS after reset
The cortex_m maskisr user-facing setting is not changed across a target
reset. However, the in-core C_MASKINTS bit was always cleared as part of
reset processing, meaning that a cortex_m maskisr on setting would not
be respected after a reset. Set C_MASKINTS based on the user-facing
setting value rather than always clearing it after reset.
Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4605
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: update all uses of interface/stlink-v2-1 to interface/stlink
Change-Id: I5e27e84d022f73101376e8b4a1bdc65f58fd348a
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4456
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/riscv/riscv-011: fix compile warning about uninitialized variable
In MSYS2 MinGW 64-bit
git clone git://git.code.sf.net/p/openocd/code openocd
$ gcc --version
gcc.exe (Rev1, Built by MSYS2 project) 8.2.0
./bootstrap
./configure --prefix=
$ cat config.status | grep CFLAGS
CFLAGS='-g -O2'
make bindir = "bin-x64"
depbase=`echo src/target/riscv/riscv-011.lo | sed 's|[^/]*$|.deps/&|;s|\.lo$||'`;\
/bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF $depbase.Tpo -c -o src/target/riscv/riscv-011.lo src/target/riscv/riscv-011.c &&\
mv -f $depbase.Tpo $depbase.Plo
libtool: compile: gcc -DHAVE_CONFIG_H -I. -D__USE_MINGW_ANSI_STDIO -I./src -I./src -I./src/helper -DPKGDATADIR=\"/mingw64/share/openocd\" -DBINDIR=\"bin-x64\" -I./jimtcl -I./jimtcl -Wall -Wstrict-prototypes -Wformat-security -Wshadow -Wextra -Wno-unused-parameter -Wbad-function-cast -Wcast-align -Wredundant-decls -Werror -g -O2 -MT src/target/riscv/riscv-011.lo -MD -MP -MF src/target/riscv/.deps/riscv-011.Tpo -c src/target/riscv/riscv-011.c -o src/target/riscv/riscv-011.o
src/target/riscv/riscv-011.c: In function 'poll_target':
src/target/riscv/riscv-011.c:1799:6: error: 'reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
reg_cache_set(target, reg, ((data & 0xffffffff) << 32) | value);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/target/riscv/riscv-011.c:1686:17: note: 'reg' was declared here
unsigned int reg;
^~~
cc1.exe: all warnings being treated as errors
make[2]: *** [Makefile:3250: src/target/riscv/riscv-011.lo] Error 1
Change-Id: I6996dcb866fbace26817636f4bedba09510a087f
Signed-off-by: Svetoslav Enchev <svetoslav.enchev@gmail.com>
Reviewed-on: http://openocd.zylin.com/4635
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The cortex_m maskisr user-facing setting is not changed across a target
reset. However, the in-core C_MASKINTS bit was always cleared as part of
reset processing, meaning that a cortex_m maskisr on setting would not
be respected after a reset. Set C_MASKINTS based on the user-facing
setting value rather than always clearing it after reset.
Change-Id: I5aa5b9dfde04a0fb9c6816fa55b5ef1faf39f8de
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4605
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Depending on range size, the loop on cache operations can take quite
some time, causing gdb to timeout.
Add keep-alive to prevent gdb to timeout.
Add also a missing dpm->finish() to balance dpm->prepare().
Change-Id: Ia87934b1ec19a0332bb50e3010b582381e5f3685
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4627
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Fix target not halting when GDB jumps to a hardware breakpoint
This issue affects riscv-0.11. It is caused by OpenOCD manually
stepping over hardware breakpoints to resume or step after a halt.
This is not necessary as GDB should remove and add breakpoints as
required.
At the moment OpenOCD still steps over hardware watchpoints manually
as GDB needs to know which address triggered the watchpoint and
OpenOCD does not currently provide this information.
Tested on the freedom-e310-arty using the GDB regression suite.
There is one regression which is a corner case caused by a GDB bug.
If a breakpoint is set in GDB and then the executable file is
discarded, GDB reverts to its default information about address
sizes e.g. on the freedom-e310-arty, 0x20400000 becomes
0xffff20400000. As a result, GDB is unable to step over breakpoints
set before the executable was discarded.
* Fix style issues
* Revert "Fix style issues"
This reverts commit 43e7e4b60a.
* Revert "Fix target not halting when GDB jumps to a hardware breakpoint"
This reverts commit e2717e4cfa.
* Don't step over breakpoints
There is no reason to restrict the command "cortex_a dacrfixup"
to the EXEC phase only.
Change the command mode to ANY so the command can be used in
the initialization phase too.
Change-Id: I498cc6b2dbdc48b3b2dd5f0445519a51857b295f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4623
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current implementation of apsel cannot be executed during the
initialization phase because it queries the DAP AP to retrieve and
print the content of IDR register, and the query is only possible
later on during the exec phase.
But IDR information is already printed by the dedicated command
apid, making redundant printing it by apsel too.
Being unable to run apsel during initialization, makes also apcsw
command (that depends on apsel) not usable in such phase.
Modify the command apsel to only set the current AP, without making
any transfer to the (possibly not initialized yet) DAP. When run
without parameters, just print the current AP number.
Change mode to COMMAND_ANY to apsel and to apcsw.
Change-Id: Ibea6d531e435d1d49d782de1ed8ee6846e91bfdf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4624
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code sets C_MASKINTS if that bit is not already set (correctly). Fix
the comment to agree.
Change-Id: If4543e2660a9fa2cdabb2d2698427a6c8d9a274c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4620
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For very low level debug or development around DAP, it is useful
to have direct access to DP registers.
Add command "dpreg" by mimic the syntax of the existing "apreg"
command:
$dap_name dpreg reg [value]
Change-Id: Ic4ab451eb5e74453133adee61050b4c6f656ffa3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4612
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In some cases by using SRST we can't halt CPU early enough. And
option PrRst is not available too. In this case the only way is
to set BOOT flag over EJTAG and reset CPU or SoC from CPU itself.
For example by writing to some reset register.
This patch is providing possibility to use user defined reset-assert
handler which will be enabled only in case SRST is disabled. It is
needed to be able switch between two different reset variants on run
time.
Change-Id: I6ef98f1871ea657115877190f7cc7a5e8f3233e4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4404
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit ad6c71e151 introduced the
variable "mmu_enabled" whose pointer is passed to cortex_a_mmu()
that initialises it.
This initialization is not visible to the compiler that issue
a compile error.
The same situation is common across the same file and the usual
workaround is to initialize it to zero; thus the same fix i
applied here.
Ticket: https://sourceforge.net/p/openocd/tickets/197/
Fixes: commit ad6c71e151 ("cortex_a: fix virt2phys when mmu is disabled")
Change-Id: I77dec41acdf4c715b45ae37b72e36719d96d9283
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4619
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The vec_ids variable is not referenced anywhere other than the vector
catch command handler. Make it local to that function.
Change-Id: Ie5865e8f78698c19a09f0b9d58269ced1c9db440
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4606
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the MMU is not enabled on debug state entry, virt2phys cannot
perform a translation since it is unknown whether a valid MMU
configuration existed before. In this case, return the virtual
address as physical address.
Change-Id: I6f85a7a5dbc200be1a4b5badf10a1a717f1c79c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4480
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
When SWD mode is used, current OpenOCD code left the SWJ-DP in
SWD mode at exit. Also, current code is unable to switch back the
SWJ-DP in JTAG at next run, thus a power cycle of both target and
interface is required in order to run OpenOCD in JTAG mode again.
Put the SWJ-DP back to JTAG mode before exit from OpenOCD.
Use switch_seq(SWD_TO_JTAG) instead of dap_to_jtag(), because the
latter is not implemented on some interfaces. This is aligned
with the use of switch_seq(JTAG_TO_SWD) in swd_connect().
Change-Id: I55d3faebe60d6402037ec39dd9700dc5f17c53b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4493
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Commit bfc5c764df avoids reading
ttbcr and ttb0/1 at every virt2phys translation by caching them,
and it updates the cached values in armv7a_arch_state().
But the purpose of any (*arch_state)() method, thus including
armv7a_arch_state(), is to only print out and inform the user
about some architecture specific status.
Moreover, to reduce the verbosity during a GDB session, the
method (*arch_state)() is not executed anymore at debug state
entry (check use of target->verbose_halt_msg in src/openocd.c),
thus the state of translation table gets out-of-sync triggering
Error: Address translation failure
or even using a wrong address in the memory R/W operation.
In addition, the commit above breaks the case of armv7r by
calling armv7a_read_ttbcr() unconditionally.
Fixed by moving in cortex_a_post_debug_entry() the call to
armv7a_read_ttbcr() on armv7a case only.
Remove the call to armv7a_read_ttbcr() in armv7a_identify_cache()
since it is (conditionally) called only in the same procedure
cortex_a_post_debug_entry().
Fixes: bfc5c764df ("armv7a: cache ttbcr and ttb0/1 on debug
state entry")
Change-Id: Ifc20eca190111832e339a01b7f85d28c1547c8ba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4601
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
On Renesas R-Car, calling 'reset halt' and 'reset init' always made DAP inaccessible. Calling 'reset' and 'halt' seperatly worked fine.
The only differences seems to be the point in time when aarch64_init_debug_access() is called. This patch aligns the behaviour.
Change-Id: I2296c65e48414a7d9846f12a395e5eca315b49ca
Signed-off-by: Dennis Ostermann <dennis.ostermann@renesas.com>
Reviewed-on: http://openocd.zylin.com/4607
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
That's better than inventing our own. Also this fixes a build issue in
the official OpenOCD regression build.
Change-Id: I042faa5b93b26e6f6b2d62bee62f21474ec74131
Call 'mem2array' without arguments to reproduce the segmentation
fault.
Change-Id: I02bf46cc8bd317abbb721a8c75d7cbfac99eb34e
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4534
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
src/target/image.c:1055:15: runtime error: left shift of 128 by 24 places cannot be represented in type 'int'
Change-Id: I322fd391cf3f242beffc8a274824763c8c5e69a4
Signed-off-by: Cody Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4584
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
This patch fixes gdb fileio support to allow gdb console to be used as stdout.
Now we can do something like
gdb <inferior file>
(gdb) tar ext :3333
(gdb) load
(gdb) monitor arm semihosting enable
(gdb) monitor arm semihosting_fileio enable
(gdb) continue
Here: Output from inferior using puts, printf etc will be routed to gdb console.
Change-Id: I9cb0dddda1de58038c84f5b035c38229828cd744
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4538
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch implements semihosting support for AArch64. This picks
code from previously submitted AArch64 semihosting support patch
and rebases on top of reworked semihosting code. Tested in AArch64
mode on a Lemaker Hikey Board with NewLib and GDB.
Change-Id: I228a38f1de24f79e49ba99d8514d822a28c2950b
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4537
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
"asid" and "length" are separate arguments of the command.
Put space between them.
Change-Id: I36cfc1e3a01caafef4fc3b26972a0cc192b0b963
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4511
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If the "Flash Patch and Breakpoint" unit is rev.1 then it can only
accept breakpoint addresses below 0x1FFFFFFF.
Detailed info in "ARM v7-M Architecture Reference Manual", DDI0403E
at chapter "C1.11 Flash Patch and Breakpoint unit".
Print a message and return error if the address of hardware
breakpoint cannot be handled by the breakpoint unit.
Change-Id: I95c92b1f058f0dfc568bf03015f99e439b27c59b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4535
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
The call to dap_queue_ap_write() can fail and the value in CSW and
TAR becomes unknown.
Invalidate the OpenOCD cache if dap_queue_ap_write() fails.
Change-Id: Id6ec370b4c5ad07e454464780c1a1c8ae34ac870
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4564
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When using apreg to change AP registers CSW or TAR we get internal
cached value not valid anymore.
Reuse the setup functions for CSW and TAR to write them.
Invalidate the cached value before the call to force the write, thus
keeping original apreg behaviour.
Change-Id: Ib14fafd5e584345de94f2e983de55406c588ac1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4565
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace PRIx64 with TARGET_PRIxADDR to avoid build problems
when --disable-target64 is used during configure.
Change-Id: I054a27a491e86c42c9386a0488194320b808ba96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4566
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tim Newsome <tim@sifive.com>
Updates the ARM disassembler to handle PLD (PreLoad Data) commands.
Previously handled by printing a TODO message. There are three forms of
the command: literal, register, and immediate. Simply decode based off
of the A1 encoding for the instructions in the ARM ARM. Also fixes mask
to handle PLDW commands.
Change-Id: I63bf97f16af254e838462c7cfac80f6c4681c556
Signed-off-by: James Marshall <jcmarsh@gwmail.gwu.edu>
Reviewed-on: http://openocd.zylin.com/4348
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The main difference is we need to deal with hartsello/hartselhi. (Note
that there's a compile-time limit to 16 harts, but that can be changed.)
My largest target has 4 harts, so I can't tell how well this really
works. But it doesn't break anything.
Fixes#240.
Change-Id: Ie1a2a789b5e00f55174994568749da1cf3a33b92
When destroying the target, if the semihosting
pointer is set, free it.
Change-Id: I07d34918bb3fddab1eee11219dd66f4842708ec1
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4552
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I1f3fddd89597333fc1bb9535c0cd76ca3e008324
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4503
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The test is overly complicated and unreadable.
Simplify it while keeping the exact same behaviour.
Change-Id: I6b22291ca454e1eddeeab4024d3983dc4c603d3a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4512
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The name of the command is already printed before the string
in ->usage, thus it appears twice.
E.g.
> help examine
stm32f4x.cpu arp_examine arp_examine ['allow-defer']
used internally for reset processing
stm32f4x.cpu examine_deferred examine_deferred
used internally for reset processing
stm32f4x.cpu was_examined was_examined
used internally for reset processing
Remove the command name from the string in ->usage.
Change-Id: If3b1368ffff8a94eb629ae3679e2e5f2f11ae92e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4536
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In 2016, ARM released the second edition of the semihosting specs
("Semihosting for AArch32 and AArch64"), adding support for 64-bits.
To ease the reuse of the semihosting logic for other platforms
(like RISC-V), the semihosting code was isolated from the ARM
target and updated to the latest specs.
The new code is already in use since January (in GNU MCU Eclipse
OpenOCD) and no problems were reported, neither for ARM nor for
RISC-V targets, after more than 7K downloads.
The 2 new files were formatted with uncrustify.
Change-Id: Ie84dbd86a547323bb8a5d24eab68fc7dad013d96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4518
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
gcc (GCC) 8.1.0 generates new warnings and thus fails the build.
The ARM disassembler warnings actually exposed a bug in SMALW, SMULW and
SMUL instructions decoding.
Reported by Eimers on IRC.
Change-Id: I200c70f75a9e07a1f13a592addc1c5fb37714440
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4526
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This improves startup time, which is important when connecting to
simulators. One problem is that triggers that are set when the debugger
connects are not cleared until enumeration happens. Execution may halt
due to a trigger set by a previous debug session, which could confuse
the user. If this happens, triggers will be instantly enumerated, so it
will only happen once per session.
Change-Id: I3396f713f16980a8b74745a1672fe8b8a2d4abae
I'm not sure what this check is adding, and it causes problems for implementations that take some time to report that they are halted out of reset (e.g. by executing Debug ROM).
Just remove our nop implementation. The default behavior when this is
left NULL does the same thing.
Change-Id: I865976c694d24661941584cb0efc92fc26612316
Neither the initial loop to clear dirty registers (which visits all
registers starting at R2 and counting upwards) nor the final explicit
flushes ensure a write-back in arm_dpm_write_dirty_registers.
This change makes sure that both our scratch registers (i.e. R0 and
R1) are written back to the target.
Change-Id: If65be4f371cd40af9a0cfa97f3730b070b92e981
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-on: http://openocd.zylin.com/4506
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Cortex-M target used 'auto_bp_type' mode. The requested type
of breakpoint was ignored and hard (FPB) breakpoints were set in
'code memory area' 0x00000000-0x1fffffff, soft breakpoints were set above
0x20000000.
The code memory area of Cortex-M does not mean the memory is flash and
vice versa. External flash (parallel or QSPI) is usually mapped above
code memory area. Cortex-M7 ITCM RAM is mapped at 0. Kinetis
has a RAM block under 0x20000000 boundary.
Remove 'auto_bp_type' mode, set breakpoints to requested type.
Change 'cortex_m maskisr auto' handling to use a hard temporary
breakpoint everywhere: it can also workaround not working soft breakpoints
on Cortex-M7 with ICache enabled.
Change-Id: I7a9f9464c5e10bfd7f17cba1037ed07a064fa2e8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4429
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Various fixes for memory leaks, adds a target cleanup for aarch64
and ARM CTI objects.
Change-Id: I2267f0894df655fdf73d70c11ed03df0b8f8d07d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4478
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.
The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).
Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.
default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.
Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
On SMP targets, the "target smp" command creates a list of targets
that belong to the SMP cluster. Free this list when a target gets
destroyed on shutdown. For simplicity, the complete list is free'd as
soon as the first target of the SMP cluster is destroyed instead of
individually removing targets from the list.
Change-Id: Ie217ae1efb2e819c288ff3b1155aeaf0a19b06be
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
apcsw command was limited to SPROT bit only.
Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7
Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.
Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
It's not implemented for 0.11 because we don't need it. Returning error
caused 0.11 targets to not be debuggable since change
848062d0d1.
Change-Id: I8b04a1fcf3c3e8bf8340cbf39aaf475d2a213519
Neither the initial loop to clear dirty registers (which visits all
registers starting at R2 and counting upwards) nor the final explicit
flushes ensure a write-back in arm_dpm_write_dirty_registers.
This change makes sure that both our scratch registers (i.e. R0 and
R1) are written back to the target.
Change-Id: If65be4f371cd40af9a0cfa97f3730b070b92e981
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-on: http://openocd.zylin.com/4506
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Enforce OpenOCD style guide.
Change-Id: I579a9f54ed22a774bf52f6aa5bc13bcbd2e82cd8
* Fail if `git diff` fails
Change-Id: I57256b0a24247f6123cb0e25a89c1b59867cb3f9
* Maybe every line gets its own shell?
Change-Id: I1a6f83e9f3d7cfd39f8933f0dba13c3cf76f71f6
* Maybe this will error properly.
Change-Id: I50803cfc229e61158569fb6b609195f7191ecac9
* Take different approach than merge-base
Change-Id: I345cbc4eecc4755c7127e8e36e403f7b727010b1
* Fix style issues.
Change-Id: I90e71f710858524812d0ab160b25c486b7b099e7
Cortex-M target used 'auto_bp_type' mode. The requested type
of breakpoint was ignored and hard (FPB) breakpoints were set in
'code memory area' 0x00000000-0x1fffffff, soft breakpoints were set above
0x20000000.
The code memory area of Cortex-M does not mean the memory is flash and
vice versa. External flash (parallel or QSPI) is usually mapped above
code memory area. Cortex-M7 ITCM RAM is mapped at 0. Kinetis
has a RAM block under 0x20000000 boundary.
Remove 'auto_bp_type' mode, set breakpoints to requested type.
Change 'cortex_m maskisr auto' handling to use a hard temporary
breakpoint everywhere: it can also workaround not working soft breakpoints
on Cortex-M7 with ICache enabled.
Change-Id: I7a9f9464c5e10bfd7f17cba1037ed07a064fa2e8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4429
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Various fixes for memory leaks, adds a target cleanup for aarch64
and ARM CTI objects.
Change-Id: I2267f0894df655fdf73d70c11ed03df0b8f8d07d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4478
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested on PSoC6 (Cortex-M0+ core), onboard KitProg2 in CMSIS-DAP mode,
adapter_khz=1000.
Plain read:
flash read_bank 0 /dev/null
takes 48 seconds.
erase_check without this change:
flash erase_check 0
takes horrible 149 seconds!!
And the same command with the change applied takes 1.8 seconds.
Quite a difference.
Remove the erase-value=0 version of algorithm as the new one can check
for any value.
If the target is an insane slow clocked CPU (under 1MHz) algo
timeouts. Blocks checked so far are returned and the next call
uses increased timeout.
Change-Id: Ic0899011256d2114112e67c0b51fab4f6230d9cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4298
Tested-by: jenkins
Reviewed-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.
The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).
Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.
default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.
Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
On SMP targets, the "target smp" command creates a list of targets
that belong to the SMP cluster. Free this list when a target gets
destroyed on shutdown. For simplicity, the complete list is free'd as
soon as the first target of the SMP cluster is destroyed instead of
individually removing targets from the list.
Change-Id: Ie217ae1efb2e819c288ff3b1155aeaf0a19b06be
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
apcsw command was limited to SPROT bit only.
Now user can manipulate any bit except size and addrinc fields.
Can be used e.g. to set bus signal 'cacheable' on Cortex-M7
Change-Id: Ia1c22b208e46d1653136f6faa5a7aaab036de7aa
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4431
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The CTRL/STAT register in the ARM DAP DP has a debug power up
ack bit and a system power up ack bit. Some devices do not set
the system power up ack bit until sometime later. To avoid having
the initial target examination fail due to this or to have a
sticky bit error report claim power failure due to this a user
can now specify that this bit should be ignored.
Change-Id: I2451234bbe904984e29562ef6f616cc6d6f60732
Signed-off-by: Eric Katzfey <eric.katzfey@mentalbee.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3710
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This saves us from re-reading s0 before doing just about anything
program buffer related.
Improves DebugBreakpoint from 3.01s to 2.89s. Feels like the improvement
should be larger than that. Maybe my metric isn't very good.
Change-Id: I85e1a1ddbf09006d76c451a32048be7b773dcfe9
Avoid ever overflowing the DWT_COMPARATOR array by allocating space for
16 comparators (the field is masked by 0xf).
On a stm32f767zi chip (on a nucleo-767zi board) I've been seeing crashes
with address sanitizer enabled due to its (apparent) 10 present
comparators. This appears to be due to
https://sourceforge.net/p/openocd/tickets/178/.
In non-address sanitizer builds, this would likely cause some random
memory to be written to in some cases. (see above bug for observations).
Change-Id: I2b7d599eb326236dbc93f74b350c442c9a502c4b
Signed-off-by: Cody P Schafer <openocd@codyps.com>
Reviewed-on: http://openocd.zylin.com/4458
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This works around some side effects of the -rtos hack, namely that we
were unable to set hardware breakpoints on harts whose misa differed
from the first one. There may be other bugs like this one lurking
elsewhere. The only proper solution is for gdb to have a better user
interface when talking to a server that exposes multiple targets, but
that's a very big project.
This fixes#194.
Change-Id: I81aedddeaa922d220e936730e9c731545953ae21
This replaces the earlier mechanism which would propagate errors only
for targets that decided they wanted to. It was suggested by Matthias
Welwarsky from the OpenOCD team.
Change-Id: Ibe8e97644abb47aff26d74b8280377d42615a4d3
If the target is held in reset we'd keep adding more delays, and since
those grow exponentially they'd get so huge it would take forever to
exit out of the loop.
Change-Id: Ieaab8b124c101fd1b12f81f905a6de22192ac662
Also call adapter_exit() before command_exit() as the latter releases
Jim interpreter so JTAG events should be released before.
Fixes memory leak reported by valgrind
Change-Id: I493f3fcba34ea2b4234148e79a4e329c866e0f05
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4474
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
If a target is run from gdb and then stopped from OpenOCD telnet interface,
halt does not show message with status and PC registers.
While on it rename 'display' to 'verbose_halt_msg' and use bool type
instead of int.
Change-Id: Ibe6589015b302e0be97258b06938c297745436a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4475
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
provide meta information for the cpsr so gdb can display the status
flags and not only a hexadecimal number
Change-Id: I9d3fb29153780adbea389d7e4175d5e19bddc256
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4460
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
a bitfield may carry a type (bool or int), add support for that.
Change-Id: Ic831a9b8eac8579e8fdd7d0f01b7f1c9259e6739
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4459
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
and move declaration of all transport_is_xxx() functions to transport.h
Change-Id: Ib229115b5017507b49655bc43b517ab6fb32f7a6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4469
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This allows a user to tell OpenOCD to prefer system bus access for
memory access, which can be useful for testing, or when there really is
a difference in behavior.
Change-Id: I8c2f15b89a2ccdae568c68ee743b75a74f9ad6bd
If we enter debug state from EL0, some registers are not accessible.
Temporarily move to EL1H and back to gain access. Also, fix
armv8_dpm_modeswitch() to not immediately restore the previous state
on elevating the privilege level.
Change-Id: Ic2a92109230ff4eb6834c00ef544397a5b7ad56a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4461
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Although the leak is negligible, the clean heap on exit will ease
valgrind testing.
Change-Id: I3a7a9c8e8dc7557aa51d0b9caa244537e5e7007d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4410
Tested-by: jenkins
Since BLX in Thumb2 always switches mode to ARM, the PC needs to be
4-bytes aligned.
Change-Id: I4f4c194fe21093cecfd9872e1d30588f4adc7257
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4382
Reviewed-by: Philipp Guehring <pg@futureware.at>
Tested-by: jenkins
Reviewed-by: Paul Sokolovsky <pfalcon@users.sourceforge.net>
Instead of re-reading ttbcr and ttb0/1 whenever a virt2phys translation
is done, cache the values once when entering debug state. Use the cached
values in armv7a_mmu_translate_va().
Change-Id: I1bc5349ad2f19b2dd75bdd48468a2c1f1e028699
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3112
Tested-by: jenkins
This patch adds support in openOCD to read/write Arm vector/floating
point registers. This is compatible with Arm vfp v3 target xml in GDB.
Please refer to binutils-gdb/gdb/features/arm/arm-vfpv3.xml
Change-Id: Id4dd1bddef51c558f1a86300c1a876d159463f18
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4421
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
This patch adds support for read/write of SIMD and floating-point register in AArch32 mode.
This patch is tested using Raspberry Pi3 halted in AArch32 mode with FP/SIMD enabled.
Software need to make sure floating-point and SIMD unit is enabled.
Change-Id: I2b3b8af02257c6420e5a70c6f4c91f839c1f5ee5
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4446
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds support in openOCD to read/write AArch64 SIMD/FP registers.
This patch depends on a previous patch which adds support to generation
of target xml by openOCD with nested architecture defined types. AArch64
SIMD/FP registers assumes various types and to support all types we
implement them as architecture defined type aarch64v which in turn
consists of various architecture defined types. This is compatible with
AArch64-FPU target xml in GDB. Please refer to
binutils-gdb/gdb/features/aarch64-fpu.xml
Change-Id: I7ffb0c21b3c2e08f13720b765408b30aab2a9808
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4373
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This code was submitted at
https://github.com/riscv/riscv-openocd/pull/214. This change
incorporates that code, makes it build, and fixes the style to fit the
OpenOCD style guide.
I have not tested the new code because I don't have a target. It does
not cause any regressions.
Change-Id: Ic3639d822c887bd4a5517f044855fdd9d4e5a46d
Mostly addresses #207.
Also changed dmi_read() to return an error, and fixed all the call sites
to propagate that error if possible.
Change-Id: Ie6fd1f9e7eb46ff92cdb5021a7311ea7334904f1
This change contains an alternative to Matthias Welwarsky's #4130
(target-prefixed commands) and to #4293 (event handlers).
get_current_target() must retrieve the target associated to the current
command. If no target associated, the current target of the command
context is used as a fallback.
Many Tcl event handlers work with the current target as if it were
the target issuing the event.
current_target in command_context is a number and has to be converted
to a pointer in every get_current_target() call.
The solution:
- Replace current_target in command_context by a target pointer
- Add another target pointer current_target_override
- get_current_target() returns current_target_override if set, otherwise
current_target
- Save, set and restore current_target_override to the current prefix
in run_command()
- Save, set and restore current_target_override to the event invoking
target in target_handle_event()
While on it use calloc when allocating a new command_context.
Change-Id: I9a82102e94dcac063743834a1d28da861b2e74ea
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4295
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Instead of asserting, return error when an abstract register access
fails on running target.
Fixes#201
Change-Id: I1ab3b31b0a4babf83c44f95ee2eeca92ef906d2f
It confuses users of IDEs like Eclipse, which request to read registers
that don't exist on the target.
Fixes#176
Change-Id: Ie2504140bfc70eba0d88fd763aacd87895aa20ff
When authdata_write sets the authenticated bit, examine() every OpenOCD
target that is connected to the DM that we were authenticated to.
Change-Id: I542a1e141e2bd23d085e507069a6767e66a196cd
They can be used to authenticate to a Debug Module.
There's a bit of a chicken and egg problem here, because the RISCV
commands aren't available until the target is initialized, but
initialization involves examine(), which can't interact with the target
until authentication has happened. So to use this you run `init`, which
will print out an error, and then run the `riscv authdata_read` and
`riscv authdata_write` commands. When authdata_write() notices that the
authenticated bit went high, it will call examine() again.
Example usage (very simple challenge-response protocol):
```
init
set challenge [ocd_riscv authdata_read]
riscv authdata_write [expr $challenge + 1]
reset halt
```
Change-Id: Id9ead00a7eca111e5ec879c4af4586c30af51f4d
this patch contains several changes to run control and state
handling together with gdb:
- graceful handling of target/gdb desync on resume, step and halt
- a default gdb-attach event executing the "halt" command, to meet gdb
expectation of target state when it attaches
- call target_poll() after Ctrl-C command from gdb
- call target_poll() after resume and step through a vCont packet
- fix log message forwarding on vCont stepping, also move an aarch64
log message from INFO to DEBUG level to prevent messing up the gdb
console during source-line stepping
- fix oversight in vCont support that messes up breakpoint handling
during stepping
Change-Id: Ic79db7c2b798a35283ff752e9b12475486a1f31a
Fixes: d301d8b42f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4432
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
target_start_algorithm does not download the algorithm. It only starts
it. It expects someone else to have already written the algorithm code
into the proper location before calling it.
Change-Id: I5e04406eed0ebb1c23e550dbf8d9f1204c432603
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4435
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When debugging Thumb-2 code, Gdb will at times send a
breakpoint packet 'Z0,<addr>,3', the number 3 denoting that
the instruction to break on is 32 bits long. Handle this by
replacing it with two consecutive 16bit Thumb BKPTs and make
sure to save and restore the full, original 32bit
instruction.
Note that this fix is only applicable if you debug a bare-metal program
(like the linux kernel) with the 'wrong' gdb, e.g. use an
"arm-linux" gdb instead of an "arm-eabi" gdb. But since most people
may not know about the subtle differences between gdb configurations
regarding thumb2 breakpoints it's still valid.
Change-Id: Ib93025faf35b11f0dba747a8c1fc36fd09a4c0f8
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4241
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
if armv7a_l1_d_cache_clean_inval_all will fail, error value is never
forwarded. So make sure we do it from now.
Change-Id: I02acfaa938ec09f58df77191d13d8f4bb3308720
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4384
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Images build improperly (by simply concatenating separate images) were accepted,
but anything after the first end-of-file record *silently* ignored. Now emit warning
for intel and motorola images upon non-whitespace after first end-of-file record but
continue reading anyway.
ST ships some images broken that way in their CubeMX packages ...
Change-Id: I0c5d08fa90070fed11fb805c5f0dc39817048176
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
... by disabling all triggers, single stepping, enabling them, and then
resuming as usual. Without this change, you'd just be stuck on an
address trigger and would have to manually disable it.
Change-Id: I5834984671baa6b64f72e533c4aa94555c64617e
Fixed abstract register access for registers that aren't XLEN wide.
Avoided excessive errors cases where we attempted to execute a fence but
failed.
Don't mark all the CSRs as caller-save. gdb was saving/restoring
dscratch, which broke function calls as a side effect. dscratch is
accessible for people who really know what they're doing, but gdb should
never quietly access it. The same is probably true for other CSRs.
Change-Id: I7bcdbbcb7e3c22ad92cbc205bf537c1fe548b160
It's not tested because spike never reports any busy errors since every
access happens instantaneously.
Change-Id: If43ea233a99f98cd419701dc98f0f4a62aa866eb
scan-build reported a couple of problems with code in aarch64.c,
this patch cleans them up. No functional changes.
Change-Id: Ie210237ddc840a8bbcd535f86a3a5faf473132f2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4346
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some of these changes actually fix broken comparisons which could
occasionally fail. Others just clean up the code and make it more clear.
Change-Id: I6c398bdc45fa0d2716f48a74822457d1351f81a5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Command
mdw 0 0x40000000
triggers Segmentation fault on an arm.
Size parameter is a nonsence that may happen e.g. if you
mistype mdw instead of mww.
Add checking for calloc() NULL return in mdb/h/w.
Use calloc() instead of malloc() as multiplication
count * sizeof(uint32_t) overflows for size >= 0x40000000.
Change-Id: I968c944d863d1173ef932a7077d526fccb9381ae
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4349
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Don't use atomic dap operations when not necessary. Also remove
loop trying to set core power request, didn't find a platform
where it actually worked and it's slowing examination down.
Change-Id: I44e5c2f289f951b8f4579f08a841172404a52053
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4143
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
added missing instructions from latest available ejtag specification
(MD00047 v6.1 at time of writting) for trace control, fast data channel
and pcsample.
Change-Id: I30293951611265ffc2bd896f9d3ca6b310e5cac6
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3950
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This duration vs sample count is _significantly_ closer to the truth
than simply declaring the value to be 100Hz.
Change-Id: Ie8d8bdf1959e1aa7cead0631cd2c86afe77d1efc
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4221
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Leverages the existing work that added profiling via DWT_PCSR.
hla_target doesn't have direct access to the mem_ap for doing a bulk
repeated read, but simply reading the DWT_PCSR register repeatedly is
still ~2 order of magnitude faster than halt/resume.
Change-Id: Ibe451aa95143694398370fdad6939cfb6191d56f
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4220
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use DWT_PCSR if present (reads nonzero); otherwise do halt-and-sample pc.
Signed-off-by: Simon Schubert <2@0x2c.org>
Change-Id: Id2dc4665e5008cc497a2e6e6493522d038d5af42
Reviewed-on: http://openocd.zylin.com/4211
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
We're using an I/O port reset by default. The only board currently
supported (Galileo) doesn't have SRST routed on the JTAG connector.
When using 'reset halt', we must rely on Reset Break because our
adapters don't have support for PREQ#/PRDY# signals.
Tested with Intel Galileo GEN2.
Change-Id: Ia406e31c156f8001717d5b6a08bd03f71de790d3
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4016
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Just some misc cleanups without any functional changes. It's just
easier to read.
Change-Id: I66bee31f297bcbdb8cc4446b774d7714fbaa7c83
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4015
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
No functional changes, cleanup only
Change-Id: I53c422be16d0a4ff157745d31362f6483093e5eb
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4014
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When testing with Intel Galileo GEN2 I have noticed a few iterations
where probemode entry took a little longer. At most I had to read
tapstatus twice. This patch uses a loop of up to 100 iterations to
wait for tapstatus to update with PM entry results.
Change-Id: I1c87d7dde715255b3fd2460d299b9493218533fc
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These symbols are only used within this C source file. They don't need
to be exposed to the outside.
Change-Id: Idb04550ecca7f12c3fdc8c6447eeeb871961add3
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-on: http://openocd.zylin.com/4012
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reported by thesourcerer on IRC.
Change-Id: I36d4d95de176a19fdd0bf80d8b419be6ca637e98
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3893
Tested-by: jenkins
Functions mem_ap_read() and mem_ap_write() incremented address even
if addrinc=false. I overlooked this fact and moved mem_ap_setup_tar()
set wrong addresses in no-incr mode.
Fixed by preventing address increment in no-incr mode.
Change-Id: I512e12a6a64e30cf6bc5bf77e3d57d35cc33e058
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/4326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MEM-AP access through banked data registers MEM_AP_REG_BD0..3
does not increment TAR regardless of the current autoincrement mode.
mem_ap_read_u32() and mem_ap_write_u32() can keep the current
autoincrement mode instead of switching autoincrement off.
Change-Id: Ib7ec688d3e04f1da678363cd2819ce90e8910e58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4163
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem: If the same memory location is accessed alternatively
by MEM-AP banked data registers without autoincrement and by standard
autoincremented read/write, TAR register is not updated correctly.
How to replicate: On a Cortex-M issue
mdw 0xe000edf0
multiple times. When poll is on (poll reads the same memory location)
only the first read is correct.
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 20002640
0xe000edf0: 01000000
0xe000edf0: 00000000
0xe000edf0: 00000000
No problems with poll off.
0xe000edf0: 01000000
0xe000edf0: 01000000
0xe000edf0: 01000000
mem_ap_setup_tar() writes to MEM_AP_REG_TAR if requested TAR value
changed or CSW_ADDRINC_... is currently active.
However if an autoincremented access has been issued and autoinc
switched off in CSW afterwards, TAR does not get updated.
The change introduces mem_ap_update_tar_cache() which is called
after queuing of any access to MEM_AP_REG_DRW. It simulates
TAR increment to keep tar_value in sync with MEM_AP.
Crossing tar autoincrement block boundary invalidates cached value.
mem_ap_write() and mem_ap_read() do not check tar autoincrement
block boundary, mem_ap_setup_tar() is called before each transfer instead.
dap_invalidate_cache() is introduced to ensure invalidation
of all cached values during dap_dp_init() and swd_connect()
Change-Id: I815c2283d2989cffd6ea9a4100ce2f29dc3fb7b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4162
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This avoids trying to read memory from the wrong hart, if the current
hart was changed by an earlier call (eg. to poll()).
Change-Id: I73da1e01c8d01d68f01ac7fdd6c548380a70cfd3
The existing code only used Memory Access mode to read memory,
which uses 32 bit operations only.
Rework the code to check the alignment/size of the read/write operation,
and use the Memory Access mode to read aligned 32 bit memory.
When using unaligned access, or 8 or 16 bit reads, use LDR{BHW} and STR{BHW}
instead.
The exception handling is still the same as it was before (meaning it breaks
when things go wrong), but I can now read an 8 bit register correctly.
Change-Id: I739a5ee825c0226ed4a89c32895cc2a047b8dc15
Signed-off-by: Bas Vermeulen <bas@daedalean.ai>
Reviewed-on: http://openocd.zylin.com/4301
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
As part of this I improved the memory read/write fatal error handling a
bit. Now at least we try to leave autoexec turned off, and will even
restore the temp registers if the situation isn't too hosed for that.
Partly addresses Issue #142
Change-Id: I79fe3f862f11c6d20441f39162423357e73a40c1
This lets users tell OpenOCD which non-standard CSRs exist on their
target, that will also be accessible and whose existence will be
communicated to gdb.
Change-Id: I56163a9fcb84ad7ebe815ae74fbd9fcc208f5a9d
(It's really only 2 bits, but something wonky happens between gdb and
OpenOCD if I make it that size.)
Change-Id: I562a65cb0ebe5aa0edcc54c251d0fea0e26f9cb1
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: Ieea1b0dec88818e9e8d5c8c5d54aa8959556d77b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4275
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Because there is no instruction that moves just half of a 64-bit FPR
to/from a GPR, we need to use scratch memory for this operation. This
code can theoretically use:
1. DMI_DATA, if it is memory mapped in the target.
2. DMI_PROGBUF, if it is writable in the target.
3. A user-configured address.
I have only tested this code very lightly. One reason is that gdb thinks
that on RV32 harts every register is 32 bits wide. Another is that this
is mostly proof-of-concept to satisfy the small program buffer code
review, which I don't want to drag out forever.
Existing tests don't realize that floating support was broken with
RV32D, and don't realize that it still doesn't work because of the gdb
problem mentioned above.
This change improves Issue #110 but there's more work to be done.
Change-Id: I99b8a36e5fea26f1d9e16e36cf99adc7be26b944
The dhcsr_save variable was used to save the value of
cortex_m->dcb_dhcsr so it could be restored later. However, all writes
in between the save and the restore use mem_ap_write_atomic_u32, not
cortex_m_write_debug_halt_mask, which means cortex_m->dcb_dhcsr isn’t
changed anyway. Delete the unnecessary local.
Change-Id: I064a3134e21398e1ecfc9f1fa7efd7b020b52341
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4240
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In cortex_m_assert_reset, in two locations, DHCSR is written directly
using mem_ap_write_u32. This means that the cached version,
target_to_cm(target)->dcb_dhcsr, is not updated when these writes are
performed, so subsequent writes to DHCSR that use
cortex_m_write_debug_halt_mask will change those bits back to their old
values which, unless modified in that particular invocation, come from
the cache. This causes an actual, observable bug on an STM32F7 in which
running “reset run” immediately after “program” can in some cases result
in execution proceeding with C_MASKINTS set (it is cleared on line 1021
but is then set immediately afterward in cortex_m_clear_halt), causing
failure of the application. Replace these mem_ap_write_u32 calls with
cortex_m_write_debug_halt_mask calls to do the same jobs.
Change-Id: Id35ca7f6057c2df2ba9cd67c53a73b50816d0b71
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4239
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
GCC7 with -Wall warns about possible string truncation with
snprint()-type functions with "directive output may be truncated writing
1 byte into a region of size between 0 and 9
[-Werror=format-truncation=]" + "note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 12" (or similar). Fix this by
increasing sizes of buffers.
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Ib848f2a56dd658783534158947ae1be7c0e99d45
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4175
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
GCC7 with -Wextra warns about switch-case blocks which fallthrough with
"this statement may fall through [-Werror=implicit-fallthrough=]". This
can be fixed by adding "special" comments: "/* fallthrough */".
See https://gcc.gnu.org/gcc-7/changes.html
Change-Id: Iba0be791dbdd86984489b2d9a0592bb59828da1e
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/4174
Tested-by: jenkins
Add "arm semihosting_cmdline [argv0 argv1 ...]" for setting the
command line arguments for the debuggee.
[andreas.fritiofson@gmail.com]: Dynamic allocation, empty default
Change-Id: I831ddd161d602f251940e29608a154e9590fdee1
Signed-off-by: Christian Groessler <chris@groessler.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3106
Tested-by: jenkins
They're never used, so just drop them.
Change-Id: Ie137deed3e7258f9d6af7e0cb508e73df0f53ee0
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4131
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Previously it might read an address multiple times if an abstract
command took longer to execute than expected.
The new implementations reads from the target how far it has gotten
along reading memory, and resumes from there if cmderr=busy.
This ended up being a bigger change than I envisioned, but in the end it
deleted more lines than it added, so I'm happy. :-)
The downloaded program now post-increments, and there's no longer an
attempt to read the current address from the target. This made it easier
to fix the problem where at the start of the loop the current address
was already read (in regular entry) or has not yet been read (when the
first round through the loop encountered busy more than once, or busy
was encountered at least once later on).
Antonio Borneo
Leonard Crestez
Tomas Vanek
Tarek BOCHKATI
Tim Newsome
Philipp Wagner
Marc Schink
Paul Fertser
Tommy Vestermark
Greg Savin
Christopher Head
Mete Balci
Florian Fainelli
Marek Vasut
Matthias Welwarsky
Oleksij Rempel
Jean-Christian de Rivaz
Darius Rad
Cody P Schafer
Tarek BOUCHKATI
Liming Sun
YanLin Zhu
Steven Stallion
Bohdan Tymkiv
Pavel S. Smirnov
Carsten Gosvig
Kevin Gillespie
cgsfv
Ryan Macdonald
Megan Wachs
craigblackmore
Dmitry Ryzhov
Guido Günther
Svetoslav Enchev
Oleksij Rempel
Paul Bartholomew
Dennis Ostermann
Liviu Ionescu
Andreas Färber
Omair Javaid
James Marshall
Kamal Dasu
Dan Robertson
Philipp Tomsich
Matthias Welwarsky
Evan Hunter
Girts Folkmanis
Ake Rehnman
Peter Mamonov
Kaspar Schleiser
Andreas Bolsch
Gleb Gagarin
Jiri Kastner
Karl Palsson
Simon Schubert
Felipe Balbi
Bas Vermeulen
Jonas Norling
Freddie Chopin
Andreas Fritiofson
Fabio Utzig
Palmer Dabbelt