* Add a warning when eq trigger is setup and it's behavior is different
from other triggers.
* Make eq trigger's behavior consistent with other triggers in case of
length == 1.
* Fix a bug in setting chained triggers (LT, GT case).
* Improve logging.
Change-Id: Id1ed0d11971b8ed875afbb979e6c8a8b51dd3818
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
There were a couple of problems with previous implementation:
* Misalligned read would return ERROR_OK and print all zeroes.
* CMDERR_BUSY for abstract access was improperly handled:
According to the spec, no assumptions can be made about DM_DATA*
contents in such a case, but these were considered valid values from
memory.
* A fallback to one element read was implemented when DMI_STATUS_BUSY
occurred during batch reads, even though this can be accounted for.
Change-Id: I09174c61c951b2bb97a529b7f0aa5afaa995179b
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Memory region addresses are not in use for now.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9a2189e956ae59b56245ec914ab16719df857b2d
Reviewed-on: https://review.openocd.org/c/openocd/+/7762
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Right after target halt, some activities needs to be done
such as printing exception reason, disable wdts and reading
debug stubs information.
Missing activities will be submitted in the next patches.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I27aad5614d903f4bd7c8d6dba6bfb0bdb93ed8dc
Reviewed-on: https://review.openocd.org/c/openocd/+/7757
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
See section 57.6.1 in RM0432.
Change-Id: Ic4977aee74d1838f420c1d9ff19925d09f8f6e2b
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
1. update RISCV_MAX_HARTS to 2^20 according to SPEC
2. remove RISCV_MAX_REGISTERS, it's not used anywhere anymore
3. add parentheses
Change-Id: Iadf0fa1ba3bbe5b9420b8430883e140db87f4f9e
Signed-off-by: Mark Zhuang <mark.zhuang@spacemit.com>
If a target where a software breakpoint was set is not currently
available, but there are other targets in the same SMP group that are
available, then we can use those to remove the software breakpoint.
Change-Id: I9faa427c7b3aee31504e6e6599539e6f29b58d8f
Signed-off-by: Tim Newsome <tim@sifive.com>
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to section 5.6 in the RISC-V debug specification, the previous
way to set triggers was incorrect, as was discussed as part of
https://github.com/riscv/riscv-openocd/issues/870. This commit fixes the
sequence to be in line with the specification as well as adds some comments
to clarify for any future reader as to what is actually done.
Change-Id: Iffc5cc0f866a466a7aaa72a4c53ee95c9080ac9d
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
this functionality allows to query if a target belongs to some smp group
and to dynamically turn on/off smp-specific behavior
Change-Id: I469453d95e7c1640a91bc60d80c854404e508535
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
This patch fixes the handling of errno by setting the sys_errn
only if error has actually occurred during the semihosting call.
It also fixes few issues where error was not set in the first place.
Change-Id: I2fbe562f3ec5e6220b800de04cd33aa1f409c7a0
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This patch introduces function semihosting_opcode_to_str() which
converts semihosting opcodes to strings. This function is then
used in debug messages to improve log analysis and troubleshooting.
Change-Id: Iffea49dae13d6a626ae0db40d379cba3c9ea5bd3
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7726
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
* rtos/FreeRTOS: solve some conflicting usage of thread id.
1.
There are some RISCV-specific usage of thread_id, which has conflict with upstream.
Some adaptions are made in this patch, to make sure OpenOCD is sending a clear thread list to gdb.
2.
Use freertos_read_struct_value for xSchedulerRunning.
Change-Id: I001a88a0c6d8eac98a389c0217b4897f28124840
Signed-off-by: Chao Du <duchao@eswincomputing.com>
* fix typo.
Change-Id: Id6546cc74de44bbee7e44b7cb29b769a2f35ec4a
* correct the data type.
Change-Id: I28c7e111e569d94ba5f6e1ae21745ddb34d4dd12
* changes as per the review comment.
Change-Id: Ica4c705a8f2657700dc27e24790287ca802480fd
* another macro replacement.
Change-Id: Ia9330fed32d917cf87804051ba1b8d6ac42cfb7b
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
With this change, failures to resume a hart due to it not being halted
are more explicitly logged or reported as an error.
Change-Id: Ia55d8df85a908363d0f2140637ce1e47c1ab6251
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
This involves halting the target, which might have unintended side
effects, but when the debugger is connected software breakpoints must
trap to the debugger. Anything else is a terrible user experience.
Change-Id: I1f7bb610eeeb054cc3042dc6bcfc16589ce12a31
Signed-off-by: Tim Newsome <tim@sifive.com>
Intended as a place where we can interact with the target without too
much concern about preserving state and doing exactly the right thing
while poll() is going on.
Change-Id: Ic9bd441caae85901a131fd45e742599803df89b5
Signed-off-by: Tim Newsome <tim@sifive.com>
Specifically, call into the RISC-V version when target becomes halted,
running, or unavailable.
I'll be using unavailable shortly.
Change-Id: I9ffffdccbf22e053fe6390d656b362bf9ab9559a
Signed-off-by: Tim Newsome <tim@sifive.com>
Will be used later when we want to do a quick halt/resume.
Change-Id: Ib80166234c4c277b7d9ce26b7566ac0f93017e64
Signed-off-by: Tim Newsome <tim@sifive.com>
* Only set ebreak bits that might be supported based on misa.
* Don't write dcsr if its value wouldn't change.
Change-Id: I7087af0b0df0fbdbf994373b5c887b9b389df872
Signed-off-by: Tim Newsome <tim@sifive.com>
Make it callable earlier, handle `supported` being NULL, and make enum
names more clear.
Change-Id: If4d286b54ccfc01eb5de5a57eb18f748c920e979
Signed-off-by: Tim Newsome <tim@sifive.com>
The riscv013_on_halt function was being called but its implementation was
empty, providing no additional functionality. Removed the function declaration,
calls to it, and its implementation since it is not required.
Change-Id: I425ea890deadeec945f0a47af247f3f99172e801
Signed-off-by: Tim Newsome <tim@sifive.com>
Otherwise I get a compiler warning, which fails the build.
Change-Id: Ib7d4ab85160b537d07c74f8651ac42906fd661ed
Signed-off-by: Tim Newsome <tim@sifive.com>
When halted we don't need to read all 3 instructions before deciding the
sequence doesn't match.
Change-Id: I9f8345960ce27e859265af901a368166a70b9fde
Signed-off-by: Tim Newsome <tim@sifive.com>
* rtos/FreeRTOS: pxCurrentTCB should be used for judgment.
The current TCB is stored in pxCurrentTCB, which is somehow RISC-V-specific, should not be overwritten from upstream (#816).
* fix the code style check.
Signed-off-by: Chao Du <duchao@eswincomputing.com>
Change-Id: I9ffa8947f0cb9e93c7d96866882a5a1e8e69afad
* revert some over-changes in last commit.
Change-Id: Ie88bd75b59190503db11ee4538281bd13b554e50
Signed-off-by: Chao Du <duchao@eswincomputing.com>
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
The original document from Jedec does not report the entry for
"21 NXP (Philips)", replaced by "c". It's clearly a typo.
Keep the line from JEP106BF.01 for "NXP (Philips)".
Change-Id: I30215c4ff08d5f112305cde6ab7a3176cdcef948
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7727
Tested-by: jenkins
On Windows, isatty() can return any non-zero value if it's an interactive
device. Which diverges from the ARM semihosting specification. This patch
introduces a fix to make the SYS_ISTTY operation conform to spec.
Change-Id: I9bc4f3cb82370812825d52419851910b3e3f35cc
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7725
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
The old implementation of gdb socket error handling
in the gdb_get_char_inner() differs between Windows and *nix
platforms. This patch simplifies it by using an existing
function log_socket_error() which handles most of the platform
specific things. It also provides better error messages.
Change-Id: Iec871c4965b116dc7cfb03c3565bab66c8b41958
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7724
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added debug prints to show what is the target debug reason. Also added
debug print for Ctrl-C response. This is useful for troubleshooting and
log analysis.
Change-Id: I055936257d989efe7255656198a8d73a367fcd15
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7720
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
These functions used to exist but don't anymore. (Pointed out in #863)
Change-Id: Iac6b5edd320bdff7628a788861e332f956dcd93d
Signed-off-by: Tim Newsome <tim@sifive.com>
Previously, progbuf execution did not flush or invalidate the register cache which could lead to incorrect behavior. This patch fixes it as well as refactors few sore points in the code related to it.
Change-Id: I353b931ca70a1828d4a9cc512aead00441730875
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Otherwise we may end up modifying DCSR of a different hart than
intended.
Change-Id: I39bde21a1444623ed150f2b3d504b9318b9d6191
Signed-off-by: Tim Newsome <tim@sifive.com>
This change implements the predefined type tap_state instead of generic
uint8_t in the driver
Change-Id: I3478e8d7b40b961f3ba77711179016cdcc35cd32
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7722
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This change fixes endianness support in the driver.
Change-Id: Ida360bb58e988cea0a66fdc79e1610b528846fc4
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7721
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang reports that 3rd function call argument is an uninitialized value
file esp32_apptrace.c line:1270
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I73e254d4eb0c6b3152229717d8827d334784ab92
Reviewed-on: https://review.openocd.org/c/openocd/+/7719
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Clang is unable to fully track the content of the array
write_buffer[] and incorrectly complains that it could contain
some uninitialized value.
To help clang to track the execution flow, rewrite the handling of
the buffer by using simpler indexing and by moving away cmd_byte
from the first buffer's element to the variable cmd_byte.
While there:
- fix the error codes returned while parsing the command line and
- use directly command_print_sameline() instead of passing through
intermediate buffers.
Change-Id: I1969e896887ea3a4abebee057cc04c03005fa57c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7718
Tested-by: jenkins
Clang 15.0.7 complains about snprintf output truncation due to
output between 13 and 22 bytes into a destination of size 20.
Increase the size of the buffer.
Change-Id: I0369255ca1bc02a0cf494f765e91a608c960a0d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7717
Tested-by: jenkins
Value in the 'dscsr' variable is garbage until the DAP queue is run.
Postpone evaluation of the 'secure_state' variable. Reading the
core registers in between will execute the DAP queue.
Change-Id: I44959e882dbafb1b9779e813c3d13f3b3dbcd47f
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7693
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The registers pauth_dmask and pauth_cmask are not accessible in
AARCH32 mode. Tagging them as 'hidden' is not enough and triggers
error:
Failed to read pauth_dmask register
while halting the core.
Tag the pauth registers as not existing, unless required by user.
Note: for non existing registers there should be no need to
allocate their register cache. Let's keep this for a further
improvement.
Change-Id: Iaa0d006a3d8ee611ee93333ed49a8615a6c94276
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: d0436b0cda ("armv8: Add support of pointer authentication")
Reviewed-on: https://review.openocd.org/c/openocd/+/7712
Tested-by: jenkins
Reviewed-by: Koudai Iwahori <koudai@google.com>
Register access on running target should fail if mstatus needs to be
modified.
Change-Id: Iec8e8d514ef2f5ca42606a5534cce55aaaa99180
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
- Manual integration of File-IO support from xt0.2 release
- Verified with applications linked using gdbio LSP
- No new clang static analysis warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iedc5f885b2548097ef4f11ae1a675b5944f5fdf0
Reviewed-on: https://review.openocd.org/c/openocd/+/7550
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Removed an unused include from src/jtag/adapter.c.
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
Change-Id: Ia5ea0acdfa1c011d7c88decd0f63e8032aafd699
Reviewed-on: https://review.openocd.org/c/openocd/+/7687
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function is used for commands:
- jtag tapisenabled
- jtag tapenable
- jtag tapdisable
While there, add the missing .help and .usage fields and fix the
incorrect check in jtag_tap_enable() and jtag_tap_disable().
Change-Id: I0e1c9f0b8d9fbad19d09610a97498bec8003c27e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7554
Tested-by: jenkins
While there:
- fix memory leak in case of error on values tap->chip,
tap->tapname, tap->expected_ids;
- check for out of memory error;
- fix minor coding style issue;
- add the missing .usage field;
- remove functions not in use anymore.
Change-Id: I1c8c3ffeb324e9eacb919c7e0d94fd72122c9a81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7431
Tested-by: jenkins
Change the prototype of functions:
- target_run_algorithm()
- target_wait_algorithm()
- target_wait_state()
- struct target_type::run_algorithm()
- struct target_type::wait_algorithm()
to use unsigned int for timeout_ms instead of int.
Change accordingly the variables passed as parameter.
Change-Id: I0b8d6e691bb3c749eeb2911dc5a86c38cc0cb65d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7562
Tested-by: jenkins
While there, add the missing .usage field and remove the now
unused function jim_target_tap_disabled().
Change-Id: I79afcc5097643fc264354c6c3957786a55f40498
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7561
Tested-by: jenkins
The function esp32_cmd_apptrace_generic() is not used outside the
file.
Declare it as static.
Detected through 'sparse' tool.
Change-Id: I08c6b92fb01594320bc3ae6b16067ac4eb51ca12
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7676
Tested-by: jenkins
This reverts commit 047b1a8fc2.
Commit 047b1a8fc2 ("target/image: zero-initialize ELF segments
up to p_memsz") breaks the backward compatibility introducing some
problem:
- an empty bss segment with paddr in SRAM gets zero filled at load
but does not survive after a reset, causing verify to fail;
- an empty bss segment with paddr in FLASH causes excessive flash
usage, which can exceed flash size (causing error) and makes
flash aging faster.
Revert it while looking for a better implementation.
Change-Id: Iaaf926dafce46a220a5bbe20c8576eb449996d76
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7658
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Peter Collingbourne <pcc@google.com>
Tested-by: jenkins
This way if you connect to a running target, before it's hit a breakpoint,
then when it does hit the breakpoint OpenOCD will catch it.
Change-Id: I6f1e5f169fa385f46759015786e664693c3872e4
Signed-off-by: Tim Newsome <tim@sifive.com>
Poll failure just means poll failed. It's safer to assume the target is
still running, because then if it is running and subsequently halts we can
relay this to gdb correctly. We can't do the other way around, because once
gdb thinks the target has halted, it can't deal with it spontaneously
running.
Change-Id: Idb56137f1d6baa9afc1b0e55e4a48f407b8ebe83
Signed-off-by: Tim Newsome <tim@sifive.com>
When a DM was powered down, we end up in examine() again, and clearly if
the DM was powered down we need to invalidate that cache.
Change-Id: I5eb6a289939f313e06c09cac22245db083026aa3
Signed-off-by: Tim Newsome <tim@sifive.com>
The error state is sticky, so this has to be done to recover.
Change-Id: I589f3cdab0f2351fd25f89951830cbc16c39bd93
Signed-off-by: Tim Newsome <tim@sifive.com>
Trying to disable OTP write protection by running e.g. `flash protect
1 0 1 off` would already be rejected with an error code, but that would
result in a generic "failed setting protection for blocks 0 to 1"
message. Now a more specific error message is also printed, telling the
user why it failed.
Change-Id: I6d4974eb0bcd23a0a6cf68ff955d9e59b8b1b06a
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-on: https://review.openocd.org/c/openocd/+/7615
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When a DMI operation does not succeed (either because of a timeout
or an error), the specification says that the error in the `op`
field is sticky and needs to cleared by writing `dmireset` in `dtmcs`.
This is already done for timeouts in increase_dmi_busy_delay
but not for errors.
Change-Id: I7c5f27a5cf145511a1a8b64a45a586521e1cbe41
Signed-off-by: Amaury Pouly <amaury.pouly@lowrisc.org>
Reviewed-on: https://review.openocd.org/c/openocd/+/7688
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
this new STM32 series family introduces 2 devices:
STM32C011xx (0x443) and STM32C031xx (0x453)
both devices have 32 Kbytes single flash bank.
Change-Id: I4e890789e44e3b174c0e9c0e1068383ecdbb865f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6874
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The bcm2835gpio driver preferred /dev/gpiomem for access to
memory mapped GPIO control and used /dev/mem as a fallback
only if it couldn't open /dev/gpiomem.
/dev/mem usually requires elevated rights or specific capabilities
of the opening process, so the fallback failed anyway.
Although /dev/gpiomem is the strongly preferred option with respect
to security, there could be also use cases which require /dev/mem
even if /dev/gpiomem is available (e.g. changing the GPIO pad
settings is necessary or testing/debugging OpenOCD).
It was difficult to handle such cases because they required
to block globally the system device /dev/gpiomem
(remove, rename or chmod).
Drop the fallback feature and select the memory device
by 'bcm2835gpio peripheral_mem_dev' configuration command.
Use /dev/gpiomem as a default.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I60e427bda795d7a13d55d61443590dd31d694832
Reviewed-on: https://review.openocd.org/c/openocd/+/7350
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Raspberry Pi 4 with 64-bit kernel and arm_peri_high=1 config.txt
parameter needs peripheral_base 0x47e000000, uint32_t is not enough.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Icedd084e2916657fa4478d452a5eb1e84a45c281
Reviewed-on: https://review.openocd.org/c/openocd/+/7685
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The pads were configured at a wrong memory address
if /dev/gpiomem was mapped.
The pad setting registers are not accessible in mapped /dev/gpiomem,
disable the pads setting if the driver doesn't open /dev/mem.
While on it, do not fail the driver initialization if pad mapping fails
- just emit a warning and work with unchanged pad setting.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I0bce76cade8f7efd75efd9087a7d9ba6511a6239
Reviewed-on: https://review.openocd.org/c/openocd/+/7684
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit introduces a new function, which can be used to reduce number
of register accesses.
Change-Id: I125809726eb7797b11121175c3ad66bedb66dd0d
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Since writing a register can make some GPRs dirty (e.g. S0, S1), registers
should be flushed in reverse order, so GPRs are flushed last.
Change-Id: Ice352a4df4ae064619c0f9905db634a7b57e4711
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Commit dd9137dc0e ("pld/virtex2: add missing error checks") adds
checks on the return value of several functions, allowing also
virtex2_read_stat() to propagate such returned values.
This triggers an error with clang, as it is now able to identify a
possible execution path that makes uninitialized the variable
status.
Check for the returned value of virtex2_read_stat() before using
the variable status and propagate the returned value.
While there, drop a useless empty string.
Change-Id: I7a23d3f904d4e07cdb6f6dfdf1179889b6b8afb8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7657
Reviewed-by: Daniel Anselmi <danselmi@gmx.ch>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The static analyser 'sparse' complains about using sizeof() on a
struct that has variable size:
src/rtos/uCOS-III.c:267:32: warning: using sizeof on a flexible structure
src/rtos/uCOS-III.c:269:41: warning: using sizeof on a flexible structure
src/rtos/uCOS-III.c:275:66: warning: using sizeof on a flexible structure
The struct ucos_iii_params contains either constants values for
different target type and variable fields. The last field is an
variable size array, always allocated to UCOS_III_MAX_THREADS
items. It's not practical to fix this size because we would get
too huge initialization in data segment.
Split away from struct ucos_iii_params all the variable fields and
put them in struct ucos_iii_private. Add in the new struct a
pointer to the selected element of ucos_iii_params_list[] and fix
the size of array threads[] to its maximum value; this would be
allocated at run-time, avoiding impacts to data segment.
Change-Id: I569011a257783d35a8795adbda06e942b4157f2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7678
Tested-by: jenkins
The function rtos_thread_packet() is used across rtos and declared
locally as extern.
Move the prototype of the function in common include rtos.h
Change-Id: I50d311b583148a2de628de0997ef1afc9103a70e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7677
Tested-by: jenkins
The struct containing SWD and JTAG operations are declared as
extern in the C file.
Mode them in include file arm_adi_v5.h to silent 'sparse' error
for global variable definition without declaration in an include
file.
Change-Id: I59088512c052d5a120c38404a882ed512a68ca02
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7675
Tested-by: jenkins
The pointer nand_devices is used in two file.
Move the extern prototype in code.h
Detected through 'sparse' tool.
Change-Id: I7237359fd1a008770a624725cd0b3d8632b4166e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7674
Tested-by: jenkins
The internal variable 'gdb_actual_connections' is used by log and
by semihosting to determine if there are active GDB connections.
Keep the variable local in server's code and only export its value
through a dedicated function.
This solves the issue detected by 'parse' of the variable defined
as global but not declared in any include file.
Change-Id: I6e14f4cb1097787404094636f8a2a291340222dd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7673
Tested-by: jenkins
The function jtag_debug_state_machine_() is only used by a static
inline function and declared inside it as private.
The static analyser 'sparse' complains that the function is
defined as global but not cross checked against a prototype in an
include file.
Move the declaration outside the inline function so it get visible
by interface.c, which already includes interface.h
While there, change the argument type from 'unsigned' to 'unsigned
int' to pass checkpatch check.
Change-Id: Ia5dfb92dc4bc6d52ead4f0cb8c68319c83ff85b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7672
Tested-by: jenkins
Let source file to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I6197f21c857833dafc3d6e3b750c764bf4610abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7671
Tested-by: jenkins
The static analyser 'sparse' complains about values bigger that
255 that gets cast-ed and/or stored in an 8 bit variable.
Rework the functions:
- h_u32_to_le()
- h_u32_to_be()
- h_u24_to_le()
- h_u24_to_be()
- h_u16_to_le()
- h_u16_to_be()
to avoid all the related warnings, without adding any functional
change. Any modern compiler should not be impacted by this.
Change-Id: I0b84043600a41c72d0e4ddb3dd195d69e3b2896b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7670
Tested-by: jenkins
The new committed files add some warning from the static analyser
'sparse':
- Don't assign pointer to 0, use NULL.
- switch with no cases.
Fix them.
Change-Id: I2c02d629bd80b71c8e42553be5d9388bb9b6bcd0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7668
Tested-by: jenkins
The static analyser 'sparse' complains that the functions
clear_malloc() and fill_malloc() are defined global but not cross
checked against a prototype in an include file.
Rework replacements.h and replacements.c to let the former be
included by the latter.
Change-Id: I536393a9c3718dcd7e144cde8f02e169f64c88e0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7667
Tested-by: jenkins
Don't use 'extern' in a C file, but declare the exported function
in a H file.
This helps validating the function prototype across declaration
and use.
Detected through 'sparse' tool.
Change-Id: I2c22b084fb513f4b3b1b1db96dfbc8fa4bfe7238
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7666
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a jtag
driver, that the struct adapter_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of adapter_driver's declaration in interface.h
Drop the preprocessor #ifdef/#endif around the declaration, as it
has no effect when the declaration is not used and/or the symbol
does not exist.
Change-Id: I5b8f5fe48a89ff0ffce38d547c551cd196379fbf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7665
Tested-by: jenkins
Let source files to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I217c2903fdb19e1a2cce39d2536a903c3d72f3f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7664
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a pld
driver, that the struct pld_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of pld_driver's declaration in pld.h
Change-Id: I0f917aecc7534c1b51af0afa9b32ccfd33db3511
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7663
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a nor
driver, that the struct flash_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of flash_driver's declaration in driver.h
Fix some incorrect non-const declaration and remove redundant
forward declarations.
Change-Id: I5e41d094307aac4a57dfa9a70496ff3cf180bd92
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7662
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a nand
driver, that the struct nand_flash_controller is declared in the
file as non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of nand_flash_controller's declaration in driver.h
While there, drop the unused/commented boundary scan controller.
Change-Id: I7dc32cef55be13ba537abe0f4c47b135d837126c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7661
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a rtos'
file, that the struct rtos_type is declared in the file as non
static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of rtos_type's declaration in rtos.h
Change-Id: Ia96dff077407a6653b11920519c1724e4c1167a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7660
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a target's
file, that the struct target_type is declared in the file as non
static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of target_type's declaration in target_type.h
While there, fix a name clash in stm8.c
Change-Id: Ia9c681e0825cfd04d509616dbc04a0cf4944f379
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7659
Tested-by: jenkins
In case in the future I have the same idea of optimizing progbuf writes
again.
Change-Id: Ie383487691cceeff75e2c22f4c85fc1fe4873937
Signed-off-by: Tim Newsome <tim@sifive.com>
Small cleanup in target.c to get rid of few upstream differences:
- removed a pointless check for `reg->exists` - already checked
few lines above
- unify one log message with what's in upstream
Change-Id: I3fd761157382670611fa90de84e2dfc90192f473
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
Non-functional change: unused function removed that does not exist
in the OpenOCD upstream, either.
Change-Id: Ibeab5b41a24183673cc02ca919b2f7285309e6f4
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
To perform any meaningful manipulations with DR the corresponding IR should
be set to a relevant instruction, not BYPASS, so warn the user accordingly.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I42580ecd75ae824a4145f6f17f0df9bcf825b50f
Reviewed-on: https://review.openocd.org/c/openocd/+/7654
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
It's customary to use [] brackets to mean the argument is optional, but
drscan requires at least one pair of "num_bits value" so change it to ().
In common regular expressions * means 0 or more, and + means 1 or more,
so change that too.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: Ib15d833bda2aa398ad1345a042f97d91c98dbf66
Reviewed-on: https://review.openocd.org/c/openocd/+/7653
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While there, add the missing .usage field and move in target.c the
enum nvp_assert.
Change-Id: Ia4f2f962887b5a35faeaa4eae128fa2865569b24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7559
Tested-by: jenkins
Reorganize the code to parse the command line only once.
Add check for successful memory allocation.
Change-Id: Ibf6068e177c09e93150d11aecfcf079348c47c21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7555
Tested-by: jenkins
For some trivial case only, replace calls to jim-nvp with calls
to the new OpenOCD nvp.
Change-Id: Ifd9aff32b67748af8ab808e6a6b6e64f5271b888
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7553
Tested-by: jenkins
New gcc does not understand that the variable 'restore_ms' is set
to 'true' only when the variable 'ms' is assigned in
static int xtensa_write_dirty_registers(...)
{
xtensa_reg_val_t ms;
bool restore_ms = false;
...
if (...) {
ms = regval;
restore_ms = true;
...
}
...
if (restore_ms) {
USE(ms);
}
...
}
and complains about possible use of uninitialized variable 'ms'.
Sadly initialize 'ms' to zero to hide this false positive.
Change-Id: I1fb3949070c8abbf4aa45a740f0ca2fdb753d4fa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7681
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Tested-by: jenkins
Current code tests a function pointer against a numeric value that
is the same enum type as returned by the pointed function.
Clearly the author was willing to call the function and check its
returned value.
Fix the check by calling the function.
Detected through 'sparse' tool.
Change-Id: I27d18d26c2c797160a397daa32835c199014b70b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Checkpatch-ignore: GIT_COMMIT_ID
Fixes: 237e894805 ("reworked etm/etb into a generic etm part with trace capture")
Reviewed-on: https://review.openocd.org/c/openocd/+/7599
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 07e1ebcc12 ("jtag: drivers: with pointers, use NULL
instead of 0") incorrectly inverts the check, making the driver's
pathmove operation not functional and triggering two clang errors.
Fix the check on malloc() returned pointer.
Change-Id: If1f220aca67452adbcd3a1c9cf691fc984b16b27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 07e1ebcc12 ("jtag: drivers: with pointers, use NULL instead of 0")
Reviewed-on: https://review.openocd.org/c/openocd/+/7656
Tested-by: jenkins
When gatemate_set_instr() fails, the array pointed by
bit_file.raw_file.data is not freed.
Issue identified by OpenOCD Jenkins clang build.
Free the array while propagating the error.
Change-Id: I2f7fadee903f9c65cdc9ab9b52ccb5803b48a59d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 682f927f8e ("pld: add support for cologne chip gatemate fpgas")
Reviewed-on: https://review.openocd.org/c/openocd/+/7632
Tested-by: jenkins
Reviewed-by: Daniel Anselmi <danselmi@gmx.ch>
Let source file to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I8ae2f8f1fdaea5683e157247463533b17237e464
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7602
Tested-by: jenkins
On 32 bit hosts, gcc should consider constants without suffix as
32 bits values.
Use the suffix 'ULL' to guarantee it is a 64 bit.
Detected through 'sparse' tool.
Change-Id: I205ca986968fef9a536f87492d1f6c80e41829f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7601
Tested-by: jenkins
Don't compare pointers with 0, use NULL when needed.
Don't assign pointer to 0, use NULL.
Detected through 'sparse' tool.
Change-Id: Ifa81ba961c0d490cc74880b4a46b620e6358f779
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7598
Tested-by: jenkins
Don't compare pointers with 0, use NULL when needed.
Don't assign pointer to 0, use NULL.
Don't pass 0 ad pointer argument, pass NULL.
Detected through 'sparse' tool.
Change-Id: I3f867cb9c0903f6e396311e7b3970ee5fb3a4231
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7597
Tested-by: jenkins
Let source file to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I5de107b4f8a468f0e37f06171f5f0c3c0546db1a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7596
Tested-by: jenkins
Add static type to symbols that are not used elsewhere.
Detected through 'sparse' tool.
Change-Id: I2bdac5d2b06a6dbed5c27bfdb1cf36eee90ad823
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7594
Tested-by: jenkins
On 32 bit hosts, gcc should consider constants without suffix as
32 bits values. Adding a cast to convert it to 64 bits should not
be enough.
Use the suffix 'ULL' to guarantee it is a 64 bit.
Detected through 'sparse' tool.
Change-Id: If6be35bd3cbbc7c3a83e0da1407e611f07ff6e06
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7593
Tested-by: jenkins
Don't compare pointers with 0, use NULL when needed.
Don't assign pointer to 0, use NULL.
Don't pass 0 ad pointer argument, pass NULL.
While there, check for return value from malloc(), replace an
assert() with a LOG_ERROR(), drop a useless cast.
Detected through 'sparse' tool.
Change-Id: Ia7cf52221b12198aba1a07ebdfaf57ce341d5699
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7592
Tested-by: jenkins
Add static type to symbols that are not used elsewhere.
Detected through 'sparse' tool.
Change-Id: I00e151d2466868a5dce028444d326defb80d4826
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7591
Tested-by: jenkins
It looks like a false positive.
Scan-build considers as possible to:
- have list_empty() return false;
- list_for_each_safe() to not execute any loop, thus not assigning
a non-NULL value to 'block';
- the NULL pointer 'block' is passed to list_del().
This is not possible because with list_empty(), the loop runs at
least once.
Rewrite the function to simplify the code and making it easier for
scan-build to check it.
This also drops an incorrect use of list_for_each_safe(), where
the 'safe' version was not required.
Change-Id: Ia8b1d221cf9df73db1196e3f51986023dcaf78eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 8d1dcf293a ("target/espressif: add application tracing functionality over JTAG")
Reviewed-on: https://review.openocd.org/c/openocd/+/7608
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
When the function xtensa_queue_dbg_reg_read() returns error, the
array 'tmp' remains not initialized and scan-build complains while
computing buf_get_u32() that:
Result of operation is garbage or undefined
Check the returned value of xtensa_queue_dbg_reg_read() and
propagate it.
Change-Id: If0aaad068b97ef0a76560e262d16429afd469585
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 8d1dcf293a ("target/espressif: add application tracing functionality over JTAG")
Reviewed-on: https://review.openocd.org/c/openocd/+/7607
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Below warnings are fixed.
1- A function declaration without a prototype is deprecated in all
versions of C [-Werror,-Wstrict-prototypes]
2- error: variable set but not used [-Werror,-Wunused-but-set-variable]
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1cf14b8e5e3e732ebc9cacc4b1cb9009276a8ea9
Reviewed-on: https://review.openocd.org/c/openocd/+/7569
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
ARMv8-R platforms are similar to ARMv8-A regarding
JTAG and most cpu registers. ARMv8-R doesn't has MMU
but has MPU instead.
ARMv8-R platforms can be AArch32 only such as Cortex-R52,
or AArch64 capable like Cortex-R82.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: Ib086f71685d1e3704b396d478ae9399dd8a391e1
Reviewed-on: https://review.openocd.org/c/openocd/+/6843
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Linux kernel and user space border is 0xc0000000 not 0xc000000
Signed-off-by: panciyan <panciyan@eswincomputing.com>
Change-Id: I6b487cce62ac31737deca97d5f5f7bbc081280f4
Reviewed-on: https://review.openocd.org/c/openocd/+/7570
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This feature allows to transfer arbitrary data between host and
ESP32 via JTAG.
The main use cases:
1- Collecting application specific data
2- Lightweight logging to the host
3- System behaviour analysis with SEGGER SystemView
4- Source code coverage
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I95dee00ac22891fa326915a3fcac3c088cbb2afc
Reviewed-on: https://review.openocd.org/c/openocd/+/7163
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If hart can't change pc (e.g. it is running), resume command should
fail.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: I14627366d574d806ea16262b7d305d8161f8bcc2
On MacOS libc includes files from MacOSX.sdk that define the macro
#define __nonnull
without arguments, causing compile error.
Extend the existing check for clang on MacOS and undefine the
macro for gcc too.
Change-Id: Ic99de78348c6aa86561212a3aded9342e5d32e02
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7571
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
Minor changes due to kernel switch to 100 char/line.
Added four new functions.
Silent checkpatch; we don't want to diverge from Linux reference
code.
Checkpatch-ignore: MACRO_ARG_REUSE, UNNECESSARY_PARENTHESES
Checkpatch-ignore: MACRO_ARG_PRECEDENCE
Change-Id: I1d2ff25bf3bab8cd0f5c9be55c7501795490ea75
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7568
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The file list.h is taken from Linux and includes two similar
implementation of double linked lists:
- with single linked list's head (hlist_*), and
- with double linked list's head (list_*).
While the former offers a minor memory footprint improvement,
keeping two implementations makes harder for newbie developers
to approach them.
So far only the latter implementation has been used and no new
patches in gerrit is going to change that.
Drop the support for lists with single linked head.
It can be easily taken back from git history, if needed.
Change-Id: I420e5de38ab755fdfbeb2115538c61818308ec2b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7567
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add the fast read method to speed up flash verification
after programming. Works the same as fast write already
implemented.
Signed-off-by: François LEGAL <devel@thom.fr.eu.org>
Change-Id: I74611a3542a88212f0483ec8ee368aba3d1f03c7
Reviewed-on: https://review.openocd.org/c/openocd/+/7564
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The condition to check if the workspace area (used by actual MIPS code
executed on target) and data area (sandbox to put data to be read/written
to/from flash) is wrong, thus preventing the use of FAST_* commands to
program/verify FLASH.
Signed-off-by: François LEGAL <devel@thom.fr.eu.org>
Change-Id: Ic68424b7f42d44e550433a120093db5e7980fd56
Reviewed-on: https://review.openocd.org/c/openocd/+/7563
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
1.
update the rtos->thread_count in time, to make sure the allocated
thread_name_str and extra_info_str could be freed by
rtos_free_threadlist(). Otherwise the abnormal return may cause a
memory leak.
2.
remove a redundant assignment to threadid.
Signed-off-by: Chao Du <duchao@eswincomputing.com>
Change-Id: Ifabc59d501c925b3d6aec8b04b2856d2c31cc4e2
Reviewed-on: https://review.openocd.org/c/openocd/+/7549
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since the deletion of `-rtos hwthread`, there is no need to treat harts
with `-rtos` specified differently on reset.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: I88a9129936b5172bb7479dfa1255e29ff460c054
No other attempt is made at doing anything hypervisor-specific. Are
other things necessary?
Change-Id: Ib65f114888840cf0878f9bfe028c9a42b436aa3f
Signed-off-by: Tim Newsome <tim@sifive.com>
If the file read abnormally, need to close it which was opened before.
Signed-off-by: panciyan <panciyan@eswincomputing.com>
Change-Id: I6142f154741dcd38088b7add2793219ee4dd2ae9
Reviewed-on: https://review.openocd.org/c/openocd/+/7546
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This also fixes an incorrect return ERROR_xx from a jim command,
propagated from return value of rtos_smp_init().
Change-Id: Icf4893c00aabd8fadd60077c5e8a2e926f687518
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7511
Tested-by: jenkins
Print one entry per line.
While there add the mandatory 'usage' field.
Change-Id: Ia832684817f3bdbfa4cb943cd97e3f9fb2605902
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7510
Tested-by: jenkins
Print one entry per line.
While there add the mandatory 'usage' field.
Change-Id: I135556e12154e33fdbd0f71d89f6fe37c69813b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7509
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I3e5b826ca58f7ade30a443ada0cb4a9cd9ea35c2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7508
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I5389881dac25877dc32930ec36ee546e48ecc14d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7507
Tested-by: jenkins
While there, fix typo on 'exceeds'.
In a following patch, the output could be formatted and split in N
values per line to make it easier to read by humans.
Change-Id: I295111a80934393011e46311f6cf6c13f2bdc0a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7503
Tested-by: jenkins
While there, format in a human readable way the output list by
using one line per tpiu name.
Change-Id: I937c92b6c1e92509cf8aa96be1517a51bc363600
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7501
Tested-by: jenkins
While there, format in a human readable way the output list by
using one line per dap name.
Change-Id: I24a47350105b90db15808c61790f05d807120739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7498
Tested-by: jenkins
While there:
- check the number of command parameters;
- add the mandatory 'usage' field.
Change-Id: I7cd16f049753caedf19f313f7dc84be98efdba42
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7497
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I316fb31e24e94985dcc724e428b0384be7ef5bdd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7496
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I3491ed79d11c5a3e81cc9afd2423da14b8df72ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7495
Tested-by: jenkins
While there:
- format in a human readable way the output list by using one line
per tap name;
- add the mandatory 'usage' field.
Change-Id: I295449220c78fac8973478b265413342ea832f61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7494
Tested-by: jenkins
While there, format in a human readable way the output list by
using one line per cti name.
Change-Id: I6d4870ee512fe7e6935d73355c2377ad805ccc3b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7492
Tested-by: jenkins
While there, add a check for target halted and check the number of
parameters accordingly to the command name.
Change-Id: I9e8bb109c35039561997d14782fac682267aee65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7491
Tested-by: jenkins
This also fixes an incorrect return ERROR_TARGET_NOT_HALTED from a
jim command.
Change-Id: I99a02a21bedb64e60944e295c7cf24356e07be60
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7490
Tested-by: jenkins
This also fixes a mistake of the jim command returning ERROR_xx
when function rtt_read_channel_info() returns error.
While there:
- format in a human readable way the output dictionary list, while
preserving the structure of its TCL data;
- add check for the number of parameters.
Change-Id: Ica2b623699d3a606d3992975c836dae96f74b26d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7489
Tested-by: jenkins
Use full 64 bits in output; no reason to truncate at 32 bits.
Change-Id: I433815a381e147731ff0da2c805170649a9bcf38
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7487
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'flash list' as OpenOCD command.
While there:
- format in a human readable way the output dictionary list, while
preserving the structure of its TCL data;
- add the mandatory 'usage' field.
Change-Id: I1ee69870d3ab3c1cfc46cd2b8ec03de6b2300bd6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7486
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'transport select' as OpenOCD command.
This fixes and incorrect check for the return value of function
transport_select(); it returns ERROR_yy but the check is on JIM_xx.
While there, fix the coding style.
Change-Id: I9f3e8394c1a0cc0312b414c58275e1220217bbed
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7485
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'ocd_find' as OpenOCD command.
Change-Id: Id775bccc12840bcf95d8c19787beda5e7c3107fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7484
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The command 'svf' is the only command in OpenOCD that accepts
options in both forms 'option' and '-option'.
Deprecate the option format without the leading '-'.
Update the documentation and fix the on-line help.
While there:
- switch to use the new nvp.h helper;
- return ERROR_COMMAND_ARGUMENT_INVALID on invalid command args;
- fix some minor coding style rule.
Change-Id: I5b944403d92a3fa1e12d5faafc1d2a139bc16a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7534
Tested-by: jenkins
If svf_set_padding() returns error, jump to free_all label to
prevent any memory leak.
Propagate the error reported by svf_set_padding() instead of
overwriting it.
Use command_print() instead of LOG_ERROR() for command output.
Change-Id: I61fd89cad10652f2f9ef1f9d48a040e35253c3d4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7533
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The file descriptor svf_fd is not closed on command error, thus
leaking memory.
Close svf_fd on errors.
While there, properly initialize svf_fd using NULL instead of 0.
Change-Id: I5efe9ce576a3a50588b30000222665e26161dfdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7532
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: <kai.schmitz@advantest.com>
The code for JTAG WAIT recovery did not handle DP_SELECT
endianness.
While on it, mark missing ADIv6 DP SELECT1 handling as TODO.
Change-Id: I44f3bc8fc9fd2483c0293b6d4f2c51a60ca01873
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7540
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The multidrop SWD is also supported.
Change-Id: I9fefc54fc9d40a75194285cd6e0f10c5c347d9b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7537
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The value returned by target_get_gdb_arch() is something specific for GDB.
There could be several variants of the same CPU.
If we start implementing all the variants, checking the string value,
could become incorrect.
It's better to check for xtensa->common_magic == XTENSA_COMMON_MAGIC
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I20f3fdced176c3b9ab00f889743161ecad7280f9
Reviewed-on: https://review.openocd.org/c/openocd/+/7536
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Almost written from the beginning in a modern OpenOCD way.
- Endiannes support
- Proper variable types
- Align with the other rtos implementations
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0868a22da2ed2ab664c82b17c171dc59ede78d10
Reviewed-on: https://review.openocd.org/c/openocd/+/7444
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Icount triggers don't have a maskmax field at all. This is a cut and
paste error.
Change-Id: I001b3d41bf683599706dba713f7be475e8dd1668
Signed-off-by: Tim Newsome <tim@sifive.com>
When permission bits R, W, and X in PTE all three are zero,
the PTE is a pointter to the next level of the page table;
otherwise, it is a leaf PTE. Here PTE_W is missed.
Change-Id: I82a4cc4e64280f0fcad75b20e51b617520aff29b
Signed-off-by: panciyan <panciyan@eswincomputing.com>
-noreset: when using several SVF input files in a sequence it is not always
desireable to have a JTAG reset between the execution of the files.
The -noreset option skips this unwanted reset.
-addcycles <x>: some tests rely on a certain number of extra clock cycles
between the actual JTAG commands. The -addcycles option injects a number
x cycles after each SDR instruction.
Signed-off-by: Kai Schmitz <kai.schmitz@advantest.com>
Change-Id: I31932d6041dbc803be00016cd0a4f23fb2e7dbe1
Reviewed-on: https://review.openocd.org/c/openocd/+/7433
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The macro JIM_EMBEDDED was required to be defined before including
jim.h in applications that embed jimtcl.
This requirement has been dropped in 2010 by removing the file
dos/Embedder-HOWTO.txt from jimtcl in
https://github.com/msteveb/jimtcl/commit/2d8564100c86#diff-3e93fa55e666
Drop the macro definition and the comment that mandates it.
Change-Id: I36883f60f25bb25839e4ebf908159569659764dd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7518
Tested-by: jenkins
Not all compilers nor compiler versions supports the attributes
used in OpenOCD code.
Collect in a single file the workaround to handle them.
Change-Id: I92d871337281169134ce8e40b2064591518be71f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7519
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- Manual integration of NX support from xt0.2 release
- No new clang static analysis warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I95b51ccc83e56c0d4dbf09e01969ed6a4a93d497
Reviewed-on: https://review.openocd.org/c/openocd/+/7356
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We were previously not zero-initializing ELF segments between p_filesz
and p_memsz (aka BSS). However, this may be necessary depending on the
user's application. Therefore, start doing so.
Change-Id: I5a743390069583aca7ee276f53afeccf2cac0855
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7513
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
All DIDs are taken from "SAM R34/R35 Errata Sheet" (DS80000834A).
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: Ie35f58e61bb02919c0676c91938c90192481d995
Reviewed-on: https://review.openocd.org/c/openocd/+/7521
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to the datasheets these MCUs have 40Kb RAM.
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: I52b8a0c86035bccd6f3c1a478bb2e558bca4ae86
Reviewed-on: https://review.openocd.org/c/openocd/+/7520
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The driver tries to open mpsse engine for each vid pid
pair in sequence. If more vid/pid pairs are configured and
the USB device does not correspond to the first pair,
the driver shows 'unable to open ftdi device ...' error.
Match vid pid with the whole list as used in jtag_libusb_open()
instead of multiple mpsse_open() in for loop over vid/pid pairs.
Change-Id: I8ef55205be221c727607fe25b81ae21de0d96f02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7529
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Can be employed by a driver with custom libusb open.
Change-Id: I00c8a01df8780891a8b7c30e2e34ab191acdf9a8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7528
Tested-by: jenkins
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Untested, because I don't have a target that implements this.
Change-Id: Iff82c124e7caf8e8960a9da62d8e727afb2c6b8a
Signed-off-by: Tim Newsome <tim@sifive.com>
It is possible for triggers of the same type to support different match
field values, so it is needed to try all the triggers, not just the
first one.
Fixes issue #788.
Signed-off-by: Evgeniy Naydanov evgeniy.naydanov@syntacore.com
Change-Id: I4c9fbc98bae7259377456d9ad8e770232724a592
We should avoid using x16~x31 register in program buffer because there
are no such general purpose registers in RVE(Embedded) extension.
For targets that support rvE, when the parameter increment=0
and count>1 of the read_memory_progbuf function, openocd will cause
an error due to the use of the s2 register.
For example:
{Command} {riscv repeat_read} count address [size=4]
Change-Id: I8b74dcc15cd00a400f2f1354c577a82132394435
Signed-off-by: Hang Xu <xuhang@eswincomputing.com>
* Calculate the FreeRTOS type sizes and offsets more adaptively.
The definition of TickType_t varies between different targets. And it is also related to configUSE_16_BIT_TICKS option.
Thus introduce a new command to make sure we are using a correct ticktype size.
Change-Id: I9e38b331a9f07b96eb9a2c259e32377fca0106ad
Signed-off-by: Chao Du <duchao@eswincomputing.com>
* redundant semicolon.
Change-Id: Ia21f0537e476099d8fe519ef78b3328d14123a38
* Update after review.
Change-Id: I1825185ec9b0557d7e01f34a8f366661b3734aa7
* update doc
Change-Id: I24b21c88b02ca3d76f1362f2545e86c068fc0ec6
---------
Signed-off-by: Chao Du <duchao@eswincomputing.com>
This probably crept in when merging in upstream in the past.
Change-Id: Iccce4515b6b5d4a90773f6d432754b065fb240bb
Signed-off-by: Tim Newsome <tim@sifive.com>
We currently fail the transfer when issuing more than 255 transactions
at once, e.g.
> read_memory 0x10000000 32 256
CMSIS-DAP transfer count mismatch: expected 257, got 1
This is because the protocol only supports 255 transactions per packet
(65535 for block transactions), and as a result we truncate the
transaction count when assembling the packet. Fix it by running the
queue when we hit the limit.
Change-Id: Ia9e01e3af5ad035f2cf2a32292c9d66e57eafae9
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 40bac8e8c4 ("jtag/drivers/cmsis_dap: improve USB packets filling")
Reviewed-on: https://review.openocd.org/c/openocd/+/7483
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OpenOCD commands produce their TCL text result through the
pair command_print() and command_print_sameline().
The latter is used to concatenate output in a single line.
At the end of a sequence of command_print(), the last LF is taken
as part of the command result, while it is not always needed, and
it is even annoying when the output of two commands needs to be
concatenate in a single line.
Using command_print_sameline() in place of the last call to
command_print() would solve the problem but it's quite expensive
in term of coding to fix all the existing commands.
Drop the last LF, if present.
Commands that would specifically need a LF as last char, can add
an extra LF at the end of the output.
Document this behavior in command.h.
Change-Id: I6757c20fbfce923dd393083146e8d5a1f3b790b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7471
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The 'current thread' was not set when no FreeRTOS task created. Which could lead a wrongly invoking of freertos_get_thread_reg_list.
Change-Id: I0e0f8327080ef698d7ed4aae5ac2a630d532ddeb
Signed-off-by: Chao Du <duchao@eswincomputing.com>
* target/riscv: hide_csrs configuration option
This option allows users to mark certain CSRs as hidden so they could be
expluded from *reg* output and target.xml
Change-Id: Iddf8456cd3901f572f8590329ebba5229974d24a
* Update doc/openocd.texi
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
---------
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* Add command "exec_progbuf"
Command "exec_progbuf" allows to execute a user-specified sequence
of instructions using the program buffer.
Change-Id: If3b9614129d0b6fcbc33fade29d3d60b35e52f98
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
* Updated the doc:
- Minor reword and reorder of the sentences.
- Added information about C-instructions in progbuf.
- Fixed a typo (per the review).
- Added examples.
Change-Id: I88c9a3ff3c6b60614be7eafd3a6f21be722a77b7
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
* Cosmetic changes
Change-Id: I7135c9f435f640e189c7d7922a2702814dfd595f
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
---------
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
Co-authored-by: Jan Matyas <jan.matyas@codasip.com>
Also refactor shared code for clearing itrigger/etrigger/icount.
Change-Id: Iac2e756332c89d2ed43435391e3c097abc825255
Signed-off-by: Tim Newsome <tim@sifive.com>
A bunch of new SPI flash (Adesto, Cypress, XTX Tech, mainly octal)
IDs and SPI FRAM (Infineon) IDs added. Backward compatible change
of ID interpretation: The previously unused 4th byte now acts
as continuation code (0x7F) count for manufacturer id, cf.
JEDEC JEP106BC. Currently this affects only some recent octal flash
and FRAM devices, which are only supported by stmqspi and cmspi
flash drivers.
Change-Id: Ibdcac81a84c636dc68439add4461b959df429bca
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6929
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Because riscv_program_exec() tries to add an instruction every time
through.
This would cause an error accessing vector registers where VL > 14(?).
Change-Id: Ie676ca8c9be786b46aa2a4b4028ac8b27f7a4b40
Signed-off-by: Tim Newsome <tim@sifive.com>
This should make vector accesses work on 64-bit harts that implement
Zve32*. There doesn't appear to be any way to easily determine what vsew
values are allowed, so try and notice the failure.
Change-Id: Ide0722d0d67da402a4fbe88163830094e46beb84
Signed-off-by: Tim Newsome <tim@sifive.com>
While there, fix some coding style error and remove the now unused
function jim_arc_read_reg_name_field() and the macro
JIM_CHECK_RETVAL().
Change-Id: I140b4b929978b2936f2310e0b7d1735ba726c517
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7426
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Use a COMMAND_HELPER() to avoid memory leaks when the helper
COMMAND_PARSE_NUMBER() returns due to an error.
While there:
- fix potential SIGSEGV due to dereference 'type' before checking
it's not NULL;
- fix an incorrect NUL byte termination while copying to
type->data_type.id and to bitfields[cur_field].name;
- fix some coding style error;
- remove the now unused function jim_arc_read_reg_type_field().
Change-Id: I7158fd93b5d4742f11654b8ae4a7abd409ad06e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7425
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Use a COMMAND_HELPER() to avoid memory leaks when the helper
COMMAND_PARSE_NUMBER() returns due to an error.
While there:
- fix potential SIGSEGV due to dereference 'type' before checking
it's not NULL;
- fix an incorrect NUL byte termination while copying to
type->data_type.id and to bitfields[cur_field].name;
- fix some coding style error.
Change-Id: Ide4cbc829871a6a523026ccc0d3100dadc2afd06
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7424
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Long ago jim_nvp was part of jimtcl. When jimtcl dropped it,
OpenOCD kept copy of it in its code base. Current code of jim_nvp
is still related with jimtcl data types and functions.
With the target of better isolating OpenOCD code from jimtcl,
create a new file nvp.c that re-proposes only the core of the old
jim_nvp, dropping any link with jimtcl and removing the string
'jim' either from the filename and from the code.
Keep the same license from the old code, as the new files are
clearly derived from it.
Change-Id: I273448cf1f1484b10f6b6113ed7bb0fcf946482b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7423
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
The command is specified through COMMAND_HANDLER. It should not
return JIM_OK / JIM_ERR.
Change-Id: I56666414d49b0298ecc23ec7ef30c77e1e27afa8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7413
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Also drop arc_cmd_jim_get_uint32() that is now unused.
Change-Id: Ic26c3f008376db3f01215bf736fca736dd1c1a4f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7412
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes several incorrect return ERROR_xxx from a jim
command.
Change-Id: I34fe3552d3dc344eac67bf504c5d5709b707fdfd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7411
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I72a522645f62b99b313573c8bad6d4f674c5ae53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7410
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I1f9cf5d1dfa38b8a06042b5f54209e6ee2fc4e0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7409
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: Iab9bc7c25181341a632f608a8ef2d8b0bea72520
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7408
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I3c51355e7e05965327ce819a3114e370f2de5249
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7407
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
OpenOCD currently uses improper "fence" instruction:
"FENCE" opcode with empty predecessor and successor sets.
Such instruction has no effect and is reserved for future use
as a HINT instruction (RISC-V Unprivileged ISA spec V20191213,
section 2.9).
This patch fixes it by using the proper "fence rw,rw"
instruction.
Change-Id: Ia2a66059009153efef27279410850ddfd73dae38
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
SW-DPv2 and SWJ-DPv2 devices do not reply to DP_TARGETSEL write cmd.
Ignore the received ACK after TARGETSEL write.
While on it, use swd_ack_to_error_code() for unified error code
translation of the received ACK value for all other commands.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If978c88c8496e31581175385e59c32faebfd20aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
And add its own header to the rtos_xxx_stackings.c
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I084130fde7ee8645129a7cf60bb7bf59448e2f39
Reviewed-on: https://review.openocd.org/c/openocd/+/7441
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
No functional change, the delay is unchanged.
Change-Id: I5b5e837d741ac01fc573657357c5fe61ad901319
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7262
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After setting adapter speed to some values, the driver
shows the real speed little bit higher.
Although it does not impose a problem from technical point
of view because the difference is smaller than usual speed error,
it looks at least strange to the user. The documentation reads
that real frequency should be same or lower than requested.
Use proper rounding in speed -> delay and delay -> speed
conversions.
Change-Id: I1831112cc58681875548d2aeb688391fb79fa37f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7261
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
bitbang_swd_exchange(rnw=true,...) calls bitbang_interface->swd_write()
with swdio clamped to 0.
bitbang_swd_write_reg() reads 1 turnaround bit, 3 ack bits
and 1 turnaround by one call to bitbang_swd_exchange()
and then switches SWDIO to output.
AFAIK all bitbang interfaces switch SWDIO GPIO direction immediately
in bitbang_interface->swdio_drive().
The GPIO now drives SWDIO line to the value stored in the output register
which is always zero from previous bitbang_swd_exchange(rnw=true,...).
In case the following data bit (bit 0) is 1 we can observe a glitch
on SWDIO:
_____ out 1 ____
HiZ/pull-up ----\ /
\ /
\______ out 0 ______/
swdio_drive(true) swd_write(0,1)
The glitch fortunately takes place far enough from SWCLK rising edge
where SWDIO is sampled by the target, so I believe it is harmless
except some corner cases where the reflected wave is delayed on long
line.
Anyway keeping electrical signals glitch free is a good practice.
To keep performance penalty minimal, pre-write the first data
bit to SWDIO GPIO output buffer while clocking the turnaround bit.
Following swdio_drive(true) outputs the pre-written value
and the same value is rewritten by the next swd_write()
instead of glitching SWDIO.
Change-Id: I72ea9c0b2fae57e8ff5aa616859182c67abc924f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7260
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The OpenJTAG driver logs "num_cycles > 16 on run test" warning
whenever the JTAG_RUNTEST operation cycle count is larger than 16.
Instead of logging the warning and only running the first 16 TCLK
cycles, remove the warning and queue up multiple operations of up
to 16 cycles each.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Id405fa802ff1cf3db7a21e76bd6df0c2d3a0fe61
Reviewed-on: https://review.openocd.org/c/openocd/+/7420
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Works for the proprietary rt-kernel from rt-labs.
See: https://rt-labs.com/product/rt-kernel/
Change-Id: Id2c2e292c15fb17eab25e3d07db05014daa2a2b0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6668
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is optional field for the targets which has to implement
their custom stack read function.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Icbc9ed66a052fc2cc0ef67e3ec4d85ab0c2c1b94
Reviewed-on: https://review.openocd.org/c/openocd/+/7442
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Other OSes have separate files to keep stack register offsets.
Adding them for NuttX as well will provide a clearer way to expand.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1428fefefa199a95431f2073c0279dd7028ad8da
Reviewed-on: https://review.openocd.org/c/openocd/+/7250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This generalizes the little endian CRC32 function used in the OR1K
target and moves it to a common helper, so that other places do not need
to reinvent the wheel. It is directly used in the OR1K target.
Change-Id: I0e55340281a5bfd80669bb1994f3a96fecc1248a
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7415
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Polling the target makes no harm during PSoC 4 flash write in the current
OpenOCD code. Don't mask it.
Change-Id: I6625ded0162ee3a96b92188844d0d2d6c30101c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7162
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The commands 'jtag newtap' and 'swd newdap' have to work either on
HLA transport and on standard JTAG/SWD. Having a dedicated
implementation for HLA is a non-sense.
Reuse the generic code jim_jtag_newtap() and drop the files
hla_tcl.[ch] as they are now empty.
Change-Id: I9dabbdc2a6f338f23b2fd3ed1a4dc3da0200c080
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7428
Tested-by: jenkins
The same code is currently used for commands 'jtag newtap' and
'swd newdap' (plus dapdirect versions), but for SWD case the code
skips the parsing of the command line as not every flag is used.
This has the drawback that syntax errors get unchecked.
Move the check about the transport so the command line get always
parsed even when the corresponding flags are not useful.
Change-Id: I596c3beb04e9e8a9ebe6ee68a61395b679d43b3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The line reset SWD sequence is used quite often in SWD multidrop mode.
Prevent the ugly connect/disconnect adapter firmware bug workaround
to be called before each line reset.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id85bff075dba9077e4e501e2cdcfd64d5d9d0531
Reviewed-on: https://review.openocd.org/c/openocd/+/7381
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DAP_TransferBlock command saves n - 3 bytes in comparison to DAP_Transfer,
where n is number of transfers.
Use DAP_TransferBlock optionaly to save some USB bandwidth.
The change increases the speed of the write transfer
from 40 KiB/s to 42 KiB/s @ USB FS, adapter speed 1000.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ifde0159cfd44481d2b81b90daa088e731c03e26d
Reviewed-on: https://review.openocd.org/c/openocd/+/7372
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DAP write transaction occupies 5 bytes of a command packet.
DAP read transaction needs just one byte in a command packet
and expect 4 bytes in a response.
The fixed maximal number of transactions in a packet caused
packet filling less than optimal.
Compute both command and expected response sizes based on
read or write direction of each transaction.
Run the queue if one of sizes does not fit into a packet.
The change increases the speed of the mostly read transfer
from 36 KiB/s to almost 40 KiB/s @ USB FS, adapter speed 1000
due to reduction of adapter inserted RDBUFF reads.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib70812600eaae0403b8ee8673b6f897348496569
Reviewed-on: https://review.openocd.org/c/openocd/+/7364
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
USB bulk backend needs to avoid zero sized USB packets
sent after each full sized packed for performance reasons.
HID backend uses fixed size HID reports so the full size
of the report can be utilized.
Introduce packet_usable_size to reflect it.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I34094c9edac5730624480711cbd6aa65883c47c7
Reviewed-on: https://review.openocd.org/c/openocd/+/7363
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Not all variables converted, JTAG part is left as is.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ie9cc890769a2f53cb3a07fd457030e1b98910d44
Reviewed-on: https://review.openocd.org/c/openocd/+/7362
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace the direct dereference of cmsis_dap_handle by dereference
of the dap function parameter wherever possible.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I32601dbe0270267642720a8524706aa76d187c3b
Reviewed-on: https://review.openocd.org/c/openocd/+/7361
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move all pending request FIFO related variables to
the struct cmsis_dap
Pure refactoring, no functional changes.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I2cea9c1e265ac102ec0f314767b8b9afdcda9ee9
Reviewed-on: https://review.openocd.org/c/openocd/+/7360
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Simply move numicro M0 flash write assembly to contrib/loaders. Also,
modify corresponding Makefile and generated numicro_m0.inc.
To make the path more general, this patch rename the path
"contrib/loaders/flash/numicro_m4" to "contrib/loaders/flash/numicro" as
well.
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9adea24c2b3c97319a9b015cf50257f3d131dc26
Reviewed-on: https://review.openocd.org/c/openocd/+/7346
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is picked from the flash part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support flashing Nuvoton's Cortex-M4 chips: M541 & NUC442/472 series.
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9dc69eccb851df14c1b0ce2f619d7b3da0aa92aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7329
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is picked from the flash part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
It reorders Nuvoton MCU part list and spreads out the way to define the
banks' base address & size of the parts.
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I1f21f54dfdf53e5b8ea04d803347d1dbc8c321a0
Reviewed-on: https://review.openocd.org/c/openocd/+/7339
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The org.gnu.gdb.arm.m-system GDB feature defines the name in lowercase
letters.[1] Not adhering to the definition can cause issues with tools
interacting with the GDB which expect the correct casing.
[1]: https://sourceware.org/gdb/onlinedocs/gdb/ARM-Features.html
Change-Id: I0b6584a78f86b053947d79686baad5dac3ec4a00
Signed-off-by: Boris-Chengbiao Zhou <bobo1239@web.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7292
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Do not warn the user about adapter speed not being set
if the selected adapter does not support configurable speed.
This would be confusing to users.
- Minor reword in the "adapter speed is not selected" warning.
- Print the adapter name in the "adapter doesn't support
configurable speed" log entry
- Another minor reword: autoselect --> autoselecting
Signed-off-by: Jan Matyas <matyas@codasip.com>
Change-Id: I4c198b547544fd8199921f092153562c5f159134
Reviewed-on: https://review.openocd.org/c/openocd/+/7269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Do not read ID from SPI flash and suppress autodetection
if non-zero flash bank size is configured.
Change-Id: Idcf9ee6ca17f9fa89964a60da7bf11e47b4af5e7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7241
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Cortex-M support for SMP multicore targets.
This SMP implementation unlike older ones does not act
on the first halted target found. It polls targets
until a SMP group is finished and stores eventual
'halted' events instead of emitting them. As soon as polling
of a group is done, poll proceeds with SMP related tasks.
This approach improves detection of a reason why debug
stopped - a correct reason is detected for all targets,
not only for the first found.
Drawback: SMP target group should be defined in the same
order as the targets were defined.
Obsolete gdb 'J' packet/smp_gdb command core switching is not implemented,
use with rtos hwthread.
Only one core is resumed if debug_execution is requested.
Some ideas taken from Graham Sanderson's [4936]
and src/target/aarch64.c
Added error checking of armv7m_restore_context().
Change-Id: I60f5b79e74b624dc2b5835ff10e38ac2ccb23792
Link: [4936]: target/cortex_m: Add smp support for Cortex M | https://review.openocd.org/c/openocd/+/4936
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When pointer authentication is enabled, some upper bits of the link
register (LR[63:VA_SIZE]) are used to store a signature. Therefore, GDB
need to remove the signature to get backtraces.
GDB has support of pointer authentication. When pointer authenticaion is
enabled, GDB requests 8-bytes mask to the target to remove the
signature. mask[63:VA_SIZE] should be all set and mask[VA_SIZE-1:0]
should be all cleared. GDB removes the signature by addr&~mask or
addr|mask.
I added a feature to provide the mask for pointer authentication.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: I56fbbf9cc23619b6536ecd326f350c8bf137f322
Reviewed-on: https://review.openocd.org/c/openocd/+/7248
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Extended feature. This is a large patch, but is self-contained to the
eCos support and does not affect any other openocd functionality. It
does NOT affect existing eCos RTOS plugin users where their
applications do not provide the extended symbolic helper
information. If the helper symbols are not available the rtos support
code will behave as before. This "dynamic" functionality is *required*
because eCos does NOT have a fixed/hardwired, known, layout for the
thread descriptor structure. The per-application build eCos
configuration can affect the shape of the thread descriptor structure
(field presence, and hence offsets of subsequent fields) such that
constant values cannot be used to consistently interpret all possible
eCos application configurations. For historical reasons, there is not
yet a consistent namespace for the helper symbols across eCos HALs
hence the support is currently limited to specific architectures
(Cortex-M and ARM/Cortex-A). No new Clang analyser warnings are raised
by this changeset.
Change-Id: Ib3a36877326eeb56595cbca55e21b9e59a59c98a
Signed-off-by: James G. Smith <jsmith@rallysmith.co.uk>
Reviewed-on: https://review.openocd.org/c/openocd/+/6275
Reviewed-by: Alex Schuilenburg <alex.schuilenburg@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The HiFive Inventor uses this flash chip, so adding it will allow for
openocd to be used to program it. These values were taken from the
chip's documentation.
Signed-off-by: Fawaz Tirmizi <fawaz@rivosinc.com>
Change-Id: I15c9d35f99d4500f73134cdc2d1b9ab6279b491c
Reviewed-on: https://review.openocd.org/c/openocd/+/7135
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In any case flag will be set as examined.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I5177ee656f726a807269e2f4725223f50e49e855
Reviewed-on: https://review.openocd.org/c/openocd/+/7231
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With OpenOCD v0.12.0 released, drop the workarounds for 'expr'
syntax change by reverting:
- commit 320043c054 ("openocd: fix for polling during "expr"
computation");
- commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change").
Replace the call to target_call_timer_callbacks_now() with call
to target_call_timer_callbacks().
Change-Id: Iae5afc50e3f688e11176a52648efc9a6577a9a11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7405
Tested-by: jenkins
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
In FreeBSB 13.0 the build fails due to redefined macro __packed.
src/jtag/drivers/esp_usb_jtag.c:19:9: error: '__packed' macro
redefined [-Werror,-Wmacro-redefined]
#define __packed __attribute__((packed))
^
/usr/include/sys/cdefs.h:223:9: note: previous definition is here
#define __packed __attribute__((__packed__))
^
1 error generated.
Drop the macro and align the code with the other files in OpenOCD
project, where the attribute is directly applied without using a
macro.
Change-Id: I89ae943e77036206d40d4d54172cd4a73e76e5c5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Wojciech Puchar <wojtek@puchar.net>
Reviewed-on: https://review.openocd.org/c/openocd/+/7435
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
This patch fixes two corner-cases of finding RTT control block.
The first one is when there was a partial match (even single byte) at
the end of loaded buffer (uint8_t buf[1024]), but this was not part of
full match. In that case `cb_offset` was not updated correctly and the
returned `*address` was lower by the legth of the partial match. In case
of searched 'SEGGER RTT' (the default control block ID) string, it was
enough to match `buf[1023] == 'S'`, which is quite likely to happen, and
the `*address` was offset by 1 (e.g. it was 0x20000fff instead of
0x20010000).
Updating (or even maintaining) `cb_offset` is not needed, as start
address of control block can be calculated based on memory address that
was loaded into `uint8_t buf[1024]`, the offset within this buffer and
the length of expected string.
The second issue is when control block is prepended with a byte that
matches first ID character, e.g. there is `SEGGER RTT` control block ID
is prepended by another `S`, making memory contents be `SSEGGER RTT`. In
that case there was no match found.
Fix that issue by making sure that tested byte is always compared with
first byte of expected control block ID.
While at it, change names of local variables to better describe their
meaning.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Change-Id: I12aa6e202bf12bedcbb888ab595751a2a2518a24
Reviewed-on: https://review.openocd.org/c/openocd/+/7429
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This command is supposed to be a start at a compliance test for system
bus access. It doesn't pass against spike because it doesn't handle all
cases where the interface might be busy. It's not documented. As far as
I know nobody uses it.
So delete 400 lines of code instead of trying to fix it.
Change-Id: Ib94f2acb95a48f7c07d4f44206ff7373b03857f3
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
This lets the user set an itrigger trigger, which doesn't fit in the
normal breakpoint abstraction.
This implementation only allows control of a single itrigger. Hardware
could support more than one, and that may be useful to catch different
interrupts in different execution modes. But it would make the code/UI
more complex and it feels like an unlikely use case.
Change-Id: I76c88636ee73d4bd298b2bd1435cb5d052e86c91
Signed-off-by: Tim Newsome <tim@sifive.com>
Cores armv8m, e.g. Cortex-M33, can be instantiated without the
optional Security Extension.
In this case, the secure registers are not present and when GDB
try accessing them it triggers a set of errors.
For armv8m cores without security extension, don't provide to GDB
the description of the secure registers.
Change-Id: I254478a4cf883e85b786df3f62c726b2f40d88d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Torbjörn SVENSSON <torbjorn.svensson@foss.st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With flag --enable-verbose, configure enables compiling some
conditional code that with new gcc triggers an error:
error: '%04x' directive output may be truncated writing
between 4 and 8 bytes into a region of size 5
[-Werror=format-truncation=]
Extend the buffer to contain the full 8 bytes of %04x on a 'int'
and change the limit in snprintf.
Skip the intermediate buffer 's[4]'.
Align the code to the coding style.
Change-Id: Ifc8a6e4686555578a7355a1f6049471fd5e31913
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Karl Hammar <karl@aspodata.se>
Reported-by: Tommy Murphy <tommy_murphy@hotmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/376/
Reviewed-on: https://review.openocd.org/c/openocd/+/7403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flashing a SAMD21J17D was failing during NVM erase. The samd21
datasheet specifies that one cause of error conditions is executing an
NVM command while the previous command is still running. The solution
is to wait for INTFLAG.READY after a command is issued.
SAMD21J17A was not exhibiting this problem. Perhaps the later silicon
revision has slower NVM erase times.
Signed-off-by: Dan Stahlke <dan@stahlke.org>
Change-Id: I19745dae4d3fc6e3a7611dcac628e067cb41e0f0
Reviewed-on: https://review.openocd.org/c/openocd/+/7391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'vdebug mem_path' is reported in the documentation as
'{Config Command}', but the code sets mode = COMMAND_ANY.
The code of the commands sets some value that is only used during
the init phase, so the documentation is correct.
Change mode of command 'vdebug mem_path' to COMMAND_CONFIG.
Change-Id: Icb940fe382cbc75015273b35dcc8a88fc2a7d0ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7395
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
When target is stopped in WFI/WFE or is in an infinite loop, the
sampled PC will always return the same value.
Command 'profile' requires that distance between min and max PC
should be at least 2, which is not the case for constant PC, and
incorrectly enforces the check through as assert().
Move the code that reads the optional parameters 'start' and 'end'
and check the gap 'end - start' before running the profile.
For self-computed min and max, increase max (or decrease min) to
match the required constraint.
Drop the assert().
Change-Id: I2be8df8568ce8c889923888c492e4f7ce354b16b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/370/
Reviewed-on: https://review.openocd.org/c/openocd/+/7400
Tested-by: jenkins
The implementation of command 'monitor profile' has few
issues:
- the address_space is a signed int, so cannot wrap-around on
space over INT_MAX;
- max address is incremented without check for overflow;
- assert() used on errors instead of returning error codes;
- only handles 32 bits PC;
- output file created and left empty on error.
This patch fixes the first two issues, as a wider fix would be too
invasive and should be postponed in a following series.
Change-Id: Id8ead3f6db0fd5730682a0d1638f11836d06a632
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/370/
Reviewed-on: https://review.openocd.org/c/openocd/+/7394
Tested-by: jenkins
Clang complains about the variable 'orig_dfsr' that can be used
uninitialized both in cortex_a_read_cpu_memory() and in
cortex_a_write_cpu_memory().
The issue is caused by an incorrect error path that used to jump
through 'goto out'. The code after the label 'out' is specific to
handle the case of an error during memory R/W; it is incorrect to
jump there to handle an error during the initialization that
precedes the memory R/W.
Replace the 'goto out' with 'return retval'.
Remove the label 'out' that is now unused.
Change-Id: Ib4b140221d1c1b63419de109579bde8b63fc2e8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7393
Tested-by: jenkins
Commit 35a503b08d ("arm_adi_v5: add ap refcount and add get/put
around ap use") modifies the examine functions of mem_ap, cortex_m,
cortex_a and aarch64 by calling dap_put_ap() and then looking again
for the mem-ap and calling dap_get_ap().
This causes an issue if the system is irresponsive and the examine
fails and left the AP pointer to NULL. If the system was already
examined the NULL pointer will cause a SIGSEGV.
Commit b6dad912b8 ("target/cortex_m: prevent segmentation fault
in cortex_m_poll()") proposes a fix for one specific case and only
on cortex_m.
Modify all the examine functions by skipping look-up for the AP if
it was already set in a previous examine; the target's AP is not
supposed to change during runtime.
Remove the partial fix for cortex_m as it is not needed anymore.
Change-Id: I806ec3b1b02fcc76e141c8dd3a65044febbf0a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 35a503b08d ("arm_adi_v5: add ap refcount and add get/put around ap use")
Reviewed-on: https://review.openocd.org/c/openocd/+/7392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the fix, will see "Can not find free FP Comparator" error log
Change-Id: Id0d91cc02b7055e44d27507f9c05ccd48ff49838
Signed-off-by: Nima Palizban <n.palizban@gmail.com>
Fixes: fb43f1ff4e (target: Rework 'set' variable of break-/watchpoints)
Reviewed-on: https://review.openocd.org/c/openocd/+/7389
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If multiple targets are specified as -rtos <rtos_type>, the
rtos_update_threads was called only if the last target was specified as
rtos, which is inconsistent with other checks of whether or not smp target
is an rtos one.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: Ie52bc6b6c8f841d31b9590fcbc44e985d3cba0eb
Reviewed-on: https://review.openocd.org/c/openocd/+/7244
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When OpenOCD receives a step-execution command from GDB and the target
is configured as rtos=hwthread, OpenOCD reconstructs the thread-info.
However, OpenOCD does not restore the thread id which is currently
selected by GDB. Due to this issue, OpenOCD sends the information of
wrong thread to GDB after the step execution.
This commit fixes the above issue by adding a code to save/restore the
thread id selected by GDB.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: I761a1141c04d48f1290e4f09baa7c7024f86f36a
Reviewed-on: https://review.openocd.org/c/openocd/+/7358
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When OpenOCD receives 'g' packet (read general registers) from GDB and
target is configured as rtos=hwthread, hwthread_get_thread_reg_list is
called. However, it does not check if the register valid or not. Due to
this issue, OpenOCD returns invalid register values to GDB.
This commit adds a validity check to hwthread_get_thread_reg_list. If
the register is not valid, it tries to read the register from the
target.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: Iad6424b62124271ec411b1dfc044b57dfc460280
Reviewed-on: https://review.openocd.org/c/openocd/+/7357
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang ignores that xds110_swd_write_reg() is always called with
bit SWD_CMD_RNW in 'cmd' set to zero.
It then complains that the local variable 'value' gets passed by
address to xds110_swd_queue_cmd() and in case of 'read request'
such stack address get stored for later use:
src/jtag/drivers/xds110.c:1363:1: warning: Address of
stack memory associated with local variable 'value' is
still referred to by the global variable 'xds110' upon
returning to the caller. This will be a dangling
reference [core.StackAddressEscape]
To both xds110_swd_write_reg() and xds110_swd_read_reg(), add an
assert() to inform Clang about the state of bit SWD_CMD_RNW.
Change-Id: I7687c055ec71424b642e152f478723a930966e3a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7380
Tested-by: jenkins
The variable retval is assigned a value that is never used.
Scan-build reports:
Although the value stored to 'retval' is used in the
enclosing expression, the value is never actually read
from 'retval'.
Drop the dead assignment.
Change-Id: I11588dee748a55d52aa7f35bc1967b7df55af7fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7379
Tested-by: jenkins
Then also set it when we resume in examine(), which doesn't use the full
abstractions because not all required data structures are filled out
yet.
Hopefully fixes#749.
Change-Id: I0c6ab16da1f035ca2fbdb9f7be1462d44ddce3a0
Signed-off-by: Tim Newsome <tim@sifive.com>
The command should now send the full 5 byte command length, which
includes the command tag (0x19) and the 4-byte baudrate word, instead
of only the last 3 bytes of the baudrate.
Signed-off-by: Nick Kraus <nick@nckraus.com>
Change-Id: Idd6e084efd7492489aa900cdbf08f540944041cb
Reviewed-on: https://review.openocd.org/c/openocd/+/7370
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Exit the loop when no harts are running, instead of when at least one
hart has halted.
Change-Id: Ia69b626bf1fee4034bd5ccc800a651bfe0e53685
Signed-off-by: Tim Newsome <tim@sifive.com>
It used to set all states to halted, but that's not right for harts that
are now unavailable. (It might be possible to call poll() at the right
time instead of duplicating some of its code, but I didn't see an easy
way to do that. The real requirement is that target->state is set to
TARGET_UNAVAILABLE before TARGET_EVENT_HALTED is is sent in
halt_finish(), because that's what triggers hwthread_update_threads(),
which must know about unavailable harts so they can be hidden from gdb.
Change-Id: I0a0bbdd4ec9ff8c9898e04045b84e1d2512c9336
Signed-off-by: Tim Newsome <tim@sifive.com>
When SMP is enabled, gdb will always use the first target in the SMP
group. That doesn't work when that first target is unavailable, but
others in the SMP group are still available.
For cases where gdb expects an operation to affect the entire group (run
control, memory access), find the first available target in an SMP group
and use that.
Change-Id: I4bed600da3ac0fdfe4287d8fdd090a58452db501
Signed-off-by: Tim Newsome <tim@sifive.com>
There used to be entirely separate code paths depending on whether we're
in SMP mode or not. Now they're both the same.
Change-Id: I8f46295e4bc005f441af0c03d4f608c53b8a6586
Signed-off-by: Tim Newsome <tim@sifive.com>
This ensures that we populate the register cache and set target->state.
Some RISC-V changes had upset the balance.
Change-Id: I47fbf8ebd8fe39fa5b752212080f87e3b7e6e5e5
Signed-off-by: Tim Newsome <tim@sifive.com>
We don't correctly write it, so we shouldn't expect it to read back the
same value. Fixes hardware breakpoints on mcontrol triggers.
Change-Id: Ie5e445060ec9c8887af933fd8887e57308330f09
Indicate to the JTAG driver that it does not need
to read and return the DR register value after scanning the
JTAG chain.
riscv_batch_run(), calls jtag_add_dr_scan() to schedule a
DR scan operation. Eventually, this will result in the JTAG
driver performing a JTAG scan to write to or read from DR.
The decision on whether to write to and/or read from DR
register is determined by the second parameter to
jtag_add_dr_scan(), i.e. a "struct scan_field".
Of particular interest here is if
batch->fields[i]->in_value is not NULL, the JTAG developer
must return the DR value collected from the JTAG scan
operation.
When creating the DR scan operation instruction with
riscv_batch_add_dmi_write(), batch->fields[i]->in_value points
to a location in batch->data_in buffer,
meaning batch->field[i]->in_value is not NULL, and the JTAG
developer must therefore read and return the DR value collected.
The returning of the DR value is redundant in a write
operation.
This patch set batch->fields[i]->in_value to NULL to indicate
the DR value need not be returned. This allows the JTAG
developer to optimize away any code associated with returning
the DR value.
Normally, the extra work to return the DR value is negligible.
However, in one usecase it introduces significant delays
In this use case a JTAG driver forwards
all JTAG scan to a server on a network. If the server has to
return the DR value, it has to perform the JTAG scan before
replying to the JTAG driver, and only then the JTAG driver
can send the next JTAG scan operation. However, if there is
no need to return the DR value, the server can
acknowledge the JTAG operation request immediately,thus
signalling to the JTAG driver that it is free to send the next
JTAG scan operation. At the same time of receiving the second
JTAG operation the server will process the original JTAG scan.
This saves time and mitigates network delay. Also, not having
to include the DR value in resulting in smaller reply packet
from server to JTAG driver and save on network traffic.
This doubles download speeds to spike using remote bitbang.
Change-Id: Ibb37c3e32af0cc7006b22b8c4e1f31ed29c21d0f
Signed-off-by: Ooi, Cinly <cinly.ooi@intel.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Ooi, Cinly <cinly.ooi@intel.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Ooi, Cinly <cinly.ooi@intel.com>
It's only used to change what callback events are generated, and there
are none anyway. (That's probably a bug, but since 0.11 is so rare I'm
not going to worry about it.)
Fixes#757.
Change-Id: I5b5df3a9bec927fb0368304229533e2875a83f6b
Signed-off-by: Tim Newsome <tim@sifive.com>
breakpoint_add should use rtos only if request is done by gdb.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: I779d1a905c6a3640869dca162e3cc001919e8f42
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Thread name loading was not correctly handled if a ThreadX task has a NULL
name.
Signed-off-by: Giulio Fieramosca <giulio@glgprograms.it>
Change-Id: I03071930182bc2585b61ce5d8c67491710883dd6
Reviewed-on: https://review.openocd.org/c/openocd/+/7328
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target_run_flash_async_algorithm expects the source_buffer to have
at least 2 words reserved for read and write pointers in addition to the
FIFO buffer. If the size of the data to be flashed is <= 8 bytes then
the flash function will fail with "corrupted fifo read pointer" error.
Ensure the allocated buffer is big enough to hold both FIFO buffer and
read/write pointers.
Change-Id: I09c22eaac517b8cfea8e0b463f5deb6b98afd267
Signed-off-by: Simon Smiganovski <simon.smiganovski@fruitcore.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7342
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
armv7m_start_algorithm() saves register values to arch_info->context.
armv7m_wait_algorithm() restores register values from arch_info->context.
Exclude registers with flag exist = false from both loops.
While on it refactor the register restore: introduce 'struct reg' pointer
and dereference it instead of numerous accesses by a full path
from armv7m pointer.
Change-Id: I1600084db84809ee13bcf8e7828b79f8c9ff9077
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7276
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On some boards there is a HW bug: if fp unit is disabled (fs in mstatus
set to 0), accessing any fp register results in a hang (any abstract
command timeouts, untill the board is rebooted).
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: I0c0d1033889f15dcc326c4078bf9cbb5a8558565
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Clang spots a potential NULL pointer dereferencing that is instead
an incorrect use of an array of pointers:
src/rtos/hwthread.c:254:32: warning: Dereference of null pointer
[core.NullDereference]
(*rtos_reg_list)[j].number = (*reg_list)[i].number;
^~~~~~~~~~~~~~~~~~~~~
The error has not been spotted before because:
- this function is not called for the first core of the SMP node,
- for the other cores on Cortex-A it still returns valid register
value for the first 12 ARM registers, then it diverges.
Also Valgrind does not spot any issue at runtime.
Address the array correctly.
While there, use DIV_ROUND_UP() macro for the computation.
Change-Id: Ib87e60e0edfd9671091f5dcfa9aedaf1aed800d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7337
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 0cedf10f8f ("Remove duplicate of a counter in
hwthread_update_threads") introduced a code bug.
In the second foreach_smp_target() loop, variable "threads_found"
gets passed to routine hwthread_fill_thread(). By removing the
counting of threads_found from the second loop, the
incorrect thread counter value gets passed to hwthread_fill_thread().
Change-Id: Ie89e53ccd28bb72b6838ef2f12106a1fe8d00994
Suggested-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The autodetection of CMSIS-DAP v2 bulk interface is tricky
as not all adapters conform CMSIS-DAP specs.
If an interface has a string descriptor containing CMSIS-DAP,
then OpenOCD did not insisted on the correct interface class
LIBUSB_CLASS_VENDOR_SPEC.
However the relaxed test caused false autodetection of v2 bulk
interface on some CMSIS-DAP v1 adapters with an additional serial
interface with the string descriptor stupidly containing
CMSIS-DAP text.
Make the test less relaxed, refuse autodetection of the interfaces
with the class number of well known functions including CDC and MSC.
Link: https://sourceforge.net/p/openocd/tickets/368/
Change-Id: I917cb257eb42aab93560cc39c61ec35a60ce52e3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7279
Tested-by: jenkins
Reviewed-by: SilverFox <yyjdelete@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable retval is assigned a value that is never used, as it
is reassigned few lines below.
Drop the dead assignment.
Change-Id: Id4e9134408fab3e04936d36e95724bf8d3ab55aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7304
Tested-by: jenkins
Clang get confused by initializing the array uint16_t lock_word[],
casting it to (uint8_t *), then accessing the second element of
the uint8_t pointer.
src/target/dsp5680xx.c:2046:41: warning: The left operand of '<<'
is a garbage value [core.UndefinedBinaryOperatorResult]
uint16_t tmp = (buffer[0] | (buffer[1] << 8));
~~~~~~~~~ ^
Fix it by replacing the array with a single uint16_t.
The code is still depending on host endianness; no fix for this is
proposed.
Change-Id: I16dfd60cab117dd145aeecf10d9593574ff233a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7302
Tested-by: jenkins
The function esirisc_jtag_recv() can be called with argument
num_in_fields = 0, for example as consequence of calling
esirisc_jtag_continue().
In this case, num_in_bytes is zero and the allocation of the
variable-length array 'r' requires size zero.
src/target/esirisc_jtag.c:133:2: warning: Declared variable-length
array (VLA) has zero size [core.VLASize]
uint8_t r[num_in_bytes * 2];
^~~~~~~~~ ~~~~~~~~~~~~~~~~
Fix it by forcing size one when num_in_bytes is zero.
Change-Id: Id764c7b5ec4f5b3c18c7da650bbff39fc98ed049
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7301
Tested-by: jenkins
Clang assumes that size could assume a value that is not 1 nor 2
nor 4. In such condition the buffer in t is allocated (size != 1)
and not initialized. This triggers an error:
src/target/openrisc/or1k_du_adv.c:655:14: warning: 2nd function
call argument is an uninitialized value [core.CallAndMessage]
crc_calc = adbg_compute_crc(crc_calc, data[i], 8);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add the default case to cover other values of size.
After this fix, clang still complains on the same line, this time
misunderstanding the limits of the loop and considering that
buf_bswap16() only swaps the first 16 bits, thus passing not
initialized value data[2] to adbg_compute_crc()
Replace malloc() with calloc() to silent it.
Change-Id: I358d7fb2ebefd69255670641bd435b770762a301
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7300
Tested-by: jenkins
All the converters functions:
h_u64_to_le()
h_u64_to_be()
h_u32_to_le()
h_u32_to_be()
h_u24_to_le()
h_u24_to_be()
h_u16_to_le()
h_u16_to_be()
have signed type in their prototype, while the function name and
all the current use cases pass an unsigned value.
Change the prototypes to use unsigned types.
Change-Id: I76dcfdd7912b81f60902184712b2907eae9843f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7299
Tested-by: jenkins
* gdb_server: Improve info message.
Add target name and state to "Not running when halt was requested"
message.
Change-Id: Ic84e9a884b57caa270cfee0ca6fa6a0dd8e5d2bd
Signed-off-by: Tim Newsome <tim@sifive.com>
* rtos/hwthread: Nicer debug message in hwthread_update_threads()
Change-Id: Ia5931a772476a2ae186ed87cd70d7e4be2f196fb
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
E.g. the Zve* vector extensions have all the same registers as the full
V extension, but leaves misa.V clear.
Change-Id: Ib08c3612c52bb3a6b074d9431e3396c8f2f0ff27
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Prep work for handling unavailable harts.
Change-Id: I9c00ed4cdad8edeaa5a13fbec7f88f40d8af9028
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Use match field for trigger
The watchpoint cannot capture all data modifications only through the
trigger of ANY SIZE and EQUAL, and an error will occur. This patch
accommodates watchpoints by adding more types of matches
Change-Id: I5c3c908dbd49ca47755b06f5cdbe451be3a81c8b
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Change-Id: I3670347c4b00bf508373f7cc2f4950cbc09d6e2a
Signed-off-by: Xiang W <wxjstz@126.com>
* Add variable type trigger support
Change-Id: I60922c5f98574040b9a160e2aa0355871a581fe1
Signed-off-by: Xiang W <wxjstz@126.com>
* remove trailing whitespace
Change-Id: I168812e12b459ae3c4b3017c27a9b897e65d9f84
Signed-off-by: Xiang W <wxjstz@126.com>
* update triggers enumerate
Change-Id: I23a66afb0f772934b8911b522d0e4f116917519f
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* target/riscv: Deal with DMI busy in sample_memory_bus_v1()
Change-Id: I810a4c4b7f02cb40ea99b7a500dce23c1bbd9231
Signed-off-by: Tim Newsome <tim@sifive.com>
* Comment code more clearly.
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Remove extra tab
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
If we just invented thread 1 to represent the current execution, we
need to make sure the RTOS object also claims it's the current thread
so that threadx_get_thread_reg_list() doesn't attempt to read a
thread control block at 0x00000001.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I7f71e730d047858898297e4cb31db8e47e0c371c
Reviewed-on: https://review.openocd.org/c/openocd/+/7280
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv Fix dm->current_hartid corruption on hartsellen discovery
Change-Id: Iec969df2675b608365eda2c3a83a4185752430f2
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
* target/riscv Ensure HART_INDEX_DIRTY does not have side effects
Change-Id: Ie89c94d97cd4f15c1be0327fddff75beea6ae027
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
This is added for future RISC-V changes. The RISC-V debug interface can
explicitly tell a debugger when a hart is unavailable. This is used for
instance when that hart is powered down (or yet to be powered up out of
reset).
Change-Id: I8a062d59eea1e5b3c788281a75159592db024683
Signed-off-by: Tim Newsome <tim@sifive.com>
`xtensa_do_step` is invoked from `xtensa_prepare_resume` to silently
step over BP/WP before resuming.
For example; in the case of WPs (DEBUGCAUSE_DB), in the current
implementation `xtensa_do_step` will generate one more
`TARGET_EVENT_HALTED` after the original one caused by WP itself.
This patch moves the halted event cb call after
the step is done successfully.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9048e14fb316dc124847a42cfaefb1f76b5ce53e
Reviewed-on: https://review.openocd.org/c/openocd/+/7274
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Fix the declaration of riscv command 'set_mem_access'.
- Remove non existing riscv command 'set_scratch_ram'.
- Add riscv commands 'info', 'reset_delays'; copy the description
from the 'help' text.
- Don't add riscv commands 'set_prefer_sba' and 'test_sba_config_reg'
as they are marked as deprecated.
- Ensure that 'test_sba_config_reg' prints a deprecation warning
when used.
Change-Id: I39dc3aec4e7f13b69ac19685f1b593790acdde83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7268
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
This GPIO driver is common to SoCs that have in-order ARM cores
(BCM2835) as well as superscalar (BCM2836-7) and speculative
out-of-order cores (BCM2711).
For BCM2837 and BCM2711, the processor can dual-issue stores and
is free to merge writes to peripheral memory for pages mapped
MT_NORMAL_NC, which is the default provided by /dev/[gpio]mem.
This can cause glitches (or missing edges) on GPIO pins when
toggled with no delay, as pipelined writes to the same address
can get arbitrarily squelched.
To prevent this happening, make sure the preceding write ops are
flushed outside the shareable domain by using a memory barrier.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Change-Id: I8805cc0911667bcb9b7f4ca340d7f4f1cb25d096
Reviewed-on: https://review.openocd.org/c/openocd/+/7258
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: Correctly set target->state in deassert_reset
This bug didn't lead to problems, but it would with some upcoming
changes.
Change-Id: I552acbae9977150c4c9e573f8852033bc80fcebb
Signed-off-by: Tim Newsome <tim@sifive.com>
* Keep debug_reason in sync with state
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Currently 'number' field is zero in the register cache and
this causes an issue on `rtos get_thread_reg_list` calls.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Iaef11e01f55d012969bbc1933f82847d5e02fec5
Reviewed-on: https://review.openocd.org/c/openocd/+/7246
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* [riscv] step operation handler should respect handle_breakpoints parameter
When step operation is requested the OpenOCD frontend (like gdb server
or TCL server) has an option to control how existing breakpoints are
handled upon step.
Some OpenOCD frontends (like gdbserver) may choose to disable special
handling of existing breakpoints - thus handle_breakpoints is set to 0,
while others (like TCL server) expect target handler to temporary
disable the matching breakpoint to allow the step operation to complete
successfully.
In the current implementation handle_breakpoints parameter was ignored
by target-specific handler. Thus, the following sequence of commands:
```
halt
bp <current_pc> 4
step
```
Resulted in *step* operation to not change PC because of bp match.
This commit addresses this issue.
* Adjusted calls to logging facilities (addressed review comments)
Co-authored-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
Co-authored-by: Tim Newsome <tim@sifive.com>
* Properly track selecting multiple harts at once.
use_hasel is a bit of a hack.
Change-Id: Ia589ebc16bca32038d915df9988361b88e940917
Signed-off-by: Tim Newsome <tim@sifive.com>
* Clarifying comment.
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Rename set_hartsel to set_dmcontrol_hartsel
Change-Id: Iab28531281aa6fc604ec7d34974ed444ea9ea850
* Make set_dmcontrol_hartsel() more idiomatic.
Change-Id: I56a885043c515359e33b9c8a03aed637c81d1486
* Use constant for multiple harts instead of -1.
Change-Id: Iefeaf74202f2b4918d21f15f7ff7ca514175b8fb
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Also add an early exit for if any harts are unavailable.
Change-Id: I0875d4d213c9faf87b219d8d57e440881366c8f8
Signed-off-by: Tim Newsome <tim@sifive.com>
arp_waitstate will not work on not-examined state
Change-Id: I56c3e1c7e63af108e4ed1dbacebb567f9bf46264
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7230
Tested-by: jenkins
Reviewed-by: Erwan Gouriou
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: I7c3de39fb1e6c23b76e2a0a85ab75f23aac94c4d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: Ife875a966a838c37dde987bc584ad0a1f4d020d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After merging [1] 'reset halt' does not work on not responding Cortex-M.
Relax the examined tests and try to set vector catch VC_CORERESET
if debug_ap is available.
While on it add an info about examination state to debug logs.
Fixes: [1] commit 98d9f1168c ("target: reset target examined flag if target::examine() fails")
Change-Id: Ie2e018610026180af5997d70231061a275f05c76
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6745
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For 64-bit TAR setup, if 'tar_valid == false' perform the upper 32-bit
write even if the cached copy matches the upper TAR value to be written.
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Change-Id: I320377dc90a9d1d7b64cbb281b2527e56c7621ee
Reviewed-on: https://review.openocd.org/c/openocd/+/7245
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Read values must be at albuff so that can be copied to buffer
on function exit.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I74a533e8f12f1002ca06a98a7c7cd928552b4cc5
Reviewed-on: https://review.openocd.org/c/openocd/+/7226
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Actually they are the base of epc and eps
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I4f43b9609a9929399fb5d3fa0203efc8a98e94c9
Reviewed-on: https://review.openocd.org/c/openocd/+/7227
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ST-Link v2 dongles can be used with many cortex-m parts, but they have
one limitation -- they can only perform 8-bit and 32-bit writes to the
target. 16-bit writes are done using a pair of 8-bit writes. While not
usually an issue, in the case of the at91samd flash driver, the 16-bit
'command' register must have both halves written in the same
operation.
Fortunately, this register has two pad bytes above it in the address
space, making it safe to always access with 32-bit operations.
Change-Id: I44b0db9406982a8db5818c0533d3101618741db2
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7234
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There is no need to count number of examined threads twice.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: Id32ead853d1ddcd4e67062d6f795700feb20cb4b
Reviewed-on: https://review.openocd.org/c/openocd/+/7223
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The bitbang driver floods the log by many messages with very
little informational value.
Remove some LOG_DEBUGs, convert some others to LOG_DEBUG_IO.
Change-Id: I0c7539467b45543e12932c67dc71e86d58c8c6cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7220
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Make write to DP_TARGETSEL is logged the similar way as other DP register
read/writes.
While on it fix checkpatch message
'Concatenated strings should use spaces between elements'
Change-Id: I98f724c984e8c4610cc461340f4c4a7cc9627ed9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7219
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
armv7m_start_algorithm() stored all non-debug execution
registers from register cache without checking validity.
Check if the register cache is valid.
Try to read from CPU if not valid.
Issue a warning if register read fails.
Change-Id: I365f86d65243230cf521b13909575e5986a87a50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7240
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The num_reg_params parameter of target_run_algorithm() was not
updated when setting "sp" was introduced. Therefore "sp" as the last
register parameter was not passed to a target algo.
Introduce a new helper variable with correct count of register parameters
and use it everywhere needed.
Change-Id: I934a71380783d98917167f1569145808ef23540f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7225
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
This was used to track which hart a given operation must apply to. But
we already have a target associated with each operation, and from there
we can find the desired hart id. dm013_info_t already tracks
current_hartid (meaning which hart ID is currently selected by the DM).
This makes the code simpler to understand. Also it turns out we don't
need to make sure the correct hart ID is currently selected because
there are only a few real entry points.
Change-Id: Ibe8d5e156523397f245edd6ec0a5df3239b717bf
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idf3bce842b4507c1f12692b5fbcd6730637de9db
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7216
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Flash read_id/erase/write operation on running target failed
in target_run_algorithm() anyway. It generated lot of error messages.
Check the target state and bail out early if target is running.
Change-Id: I903f5f38c8e61016e5002b235e5f07803bd2ec4e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
SPI flash erase often takes longer than the fixed timeout 3 seconds.
Introduce a configurable timeout_ms parameter to rp2040_call_rom_func().
Compute the erase timeout from the number of blocks to be erased.
While on it make the timeouts shorter for connect flash, flush cache and
enter/exit xip (1 second is enough).
Change-Id: I552bfa317ee17064de3a54ec2f0c63e84ba87222
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7214
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The size of the flash write buffer should be rounded
down to the multiply of flash page size.
Using write chunks of unadjusted size results in write of chunks
unaligned to flash pages.
Change-Id: If7931362ee193dff4dc2df7ec78f13530658cf08
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7187
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it restore memory-mapped mode also after flash erase
(originally was restored after flash write only).
Change-Id: I5e153b79ac27a8439f57239ce90ce8a79c0bb8a1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7186
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Prepend stack_grab_and_prep() function name by rp2040_ prefix.
Introduce target helper variable in rp2040_stack_grab_and_prep()
and use it instead of dereferencing bank->target several times.
Move flash ID reading code to the new rp2040_spi_read_flash_id()
function.
Change-Id: I9d6e51e17e36e6230155a586065499f2f260089a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7185
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
swd_multidrop_select() uses its own retry loop.
If select fails, do_reconnect flag remains set on exit and causes
useless reconnect.
Clear do_reconnect flag in retry loop.
Change-Id: Ie06d6967d7f4a977774c8530bb8d4b3e5ab4f62c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7217
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Implementation of ADI v6 introduced banking of DP reg 0.
The accompanying change preventing DP SELECT write before
DP IDR read during connect was added to swd_connect_single() only.
Unchanged swd_connect_multidrop() / swd_multidrop_select_inner()
was broken as it emited DP SELECT and put DP to protocol error state.
Copy dap->select handling to swd_multidrop_select_inner().
Fixes: 72fb88613f (adiv6: add low level swd transport)
Change-Id: I514cd6d9ae2ba97ce3657b459df22638c278a0b1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
According to RISC-V External Debug Support Version 0.13.2 (paragraph
3.12.6), cmderr field contains a valid value only if busy is 0, so it is
incorrect to analize it on timeout.
Increase "value_buf" size so it can hold a 64-bit number represented
as a string. Previous size could only hold a 32-bit number string.
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Change-Id: If6fbc875236e6ddc59522fbc25db0129eb60ee27
Reviewed-on: https://review.openocd.org/c/openocd/+/7221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Scan-build reports:
Logic error: Uninitialized argument value
riscv.c:2688 2nd function call argument is an uninitialized value
This is a real error cause by running the command "riscv
authdata_write" without arguments. In such case 'value' is not
initialized and is passed to and used by r->authdata_write().
Reorganize the code to:
- detect the correct amount or command's arguments;
- drop the LOG_ERROR() on ERROR_COMMAND_SYNTAX_ERROR;
- drop the 'else' after 'return'.
Change-Id: I62e031220593b8308bc674b753e15d16d4c5c9ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7210
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Scan-build reports:
Logic error: Result of operation is garbage or undefined
riscv.c:1614 The result of the left shift is undefined due
to shifting by '4294967281', which is greater or
equal to the width of type 'target_addr_t'
This is a false warning due to clang that considers the impossible
case of 32 bits hart (xlen = 32) in SATP_MODE_SV48 mode
(info->va_bits = 48).
Under such case:
riscv.c:1614 ... ((target_addr_t)1 << (xlen - (info->va_bits - 1))) ...
the shift amount wraps around the unsigned type and assumes the
value 4294967281 (0xfffffff1).
Use assert() to prevent clang from complaining.
Change-Id: I08fdd2a806c350d061641e28cf15a51b397db099
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7209
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead nested assignment
riscv.c:459 Although the value stored to 'ir_user4_raw' is
used in the enclosing expression, the value is
never actually read from 'ir_user4_raw'
This is caused by the value reassigned in 'ir_user4_raw':
riscv.c:459 ir_user4[3] = (uint8_t)(ir_user4_raw >>= 8);
but never used.
Drop the DIY conversion in favor of h_u32_to_le() that does not
reassign the input value.
Change-Id: Ifad29f4c46d4a2d0a2f5a5c4104d768cc3db2794
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7208
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead assignment
riscv.c:716 Value stored to 'result' is never read
Remove the initialization of variable 'result'.
Change-Id: Ied67bb4fcfa5bace186522074247ead43a5d5cd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7207
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead initialization
riscv-013.c:2362 Value stored to 'control' during its
initialization is never read
Remove the initialization of variable 'control'.
Change-Id: I548f8175530b9a2aa4c1788549d6467bf9824584
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7206
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build complains about variable 'sbcs_orig' that can be used
not initialized.
Logic error: Assigned value is garbage or undefined
riscv-013.c:4468 Assigned value is garbage or undefined
This is caused by not checking the return value of the call
riscv-013.c:4466 dmi_read(target, &sbcs_orig, DM_SBCS);
In fact when dmi_read() returns error, the variable 'sbcs_orig' is
not assigned.
Check the returned value.
Change-Id: Ia9032a0229aa243138f95f4e13f765726a4ceae9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7205
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build triggers a warning:
Unix API: Allocator sizeof operand mismatch
dsp563xx.c:2143 Result of 'calloc' is converted to a pointer
of type 'uint8_t', which is incompatible with sizeof
operand type 'uint32_t'
It's a false positive because calloc() is properly used in this
case, as the uint8_t array is used in blocks of 4 elements to read
or write uint32_t values.
Either
calloc(sizeof(uint32_t), count);
and
malloc(count * sizeof(uint32_t));
keep triggering the same warning.
Drop the warning by using the constant '4' as size of uint32_t, as
already used few lines below.
Change-Id: I5bb1ece177774eefdc5d9cd049338f8f2be87cd7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Doxygen complains about:
adapter.h:120: warning: Unsupported xml/html tag <signal_name> found
Move the text in double quote to remove the warning.
Change-Id: Ia4ead5caa83c84e10ee2b2359048c282892170b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 82fd400542 ("jtag/adapter: Add command 'adapter gpio'")
Reviewed-on: https://review.openocd.org/c/openocd/+/7202
Tested-by: jenkins
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Resolves issues where registers are accessed when poll() logic is inactive or has not yet been triggered.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: If7a4d00938fb188b008325249627f7773c3484c5
Reviewed-on: https://review.openocd.org/c/openocd/+/7197
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When FreeRTOS (at least) is compiled with -flto, this leaves certain
static symbols with .lto_priv.0 appended to their name. Arguably this
could be considered to be a gdb or gcc bug, but one place to resolve it
for OpenOCD usage is here at symbol lookup time.
Note that the ".0" is for the first such instance of the variable as a
static; additional ones would end up as ".1", ".2", etc, and are not
considered here.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: I03580b45e8ea364392ef4e05c96276416b390cb0
Reviewed-on: https://review.openocd.org/c/openocd/+/7179
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is in preparation for a future commit that looks for an optional
suffix of .lto_priv.0 on the symbol name.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: If803332373825b73bc986bd4ea7dfaee9c625c0a
Reviewed-on: https://review.openocd.org/c/openocd/+/7178
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This will be utilized for an upcoming refactorization to support -flto
compiled programs.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: Id523c0b3ac2dad8b248ea0d2cac7b4dd2f83d293
Reviewed-on: https://review.openocd.org/c/openocd/+/7177
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Read PS from EPS[debuglevel] during fetch such that it reflects the correct value when read via telnet (not just via gdb_server).
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I8504f68989bc6d5fe451a8cb69d01c86f4ec0100
Reviewed-on: https://review.openocd.org/c/openocd/+/7195
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Requested in https://review.openocd.org/c/openocd/+/6964.
I'm making the change here so I have a chance to test it properly before
pushing it upstream.
A nice effect of this change is that we avoid some unnecessary polling
early on when gdb is connecting and we would poll once every time we
send gdb a qXfer packet.
Change-Id: I4bdb9f05839e8c1e01ff6dde49d6589595418095
Signed-off-by: Tim Newsome <tim@sifive.com>
This updates the FreeRTOS module to use the M4F FPU stacking also for the
FPV5_SP and FPV5_DP FPUs, which are found on the Cortex-M7. The FPUs are
in fact different than the FPV4_SP found on the M4, but the register
stacking is the same.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I74c45d2cfb55f55e6c557f2450068ad3c2fe9497
Reviewed-on: https://review.openocd.org/c/openocd/+/6939
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The method soft_reset_halt is optional; no need to add an
empty function.
Remove mips_mips64_soft_reset_halt() and move the TODO comment
in struct target_type.
Change-Id: Id541a75e7a08645568961d59b73a120c2238701f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7184
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Read buffer is sized for 32-bit APB version of PWRSTAT/PWRCTL registers. Initialize to zero so 8-bit JTAG register mirrors are accurate.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I81310649fa7180893d0188aab3c8a14315aaea0a
Reviewed-on: https://review.openocd.org/c/openocd/+/7183
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I2b6a8365f554e332520fa77ccf076188083a932f
Reviewed-on: https://review.openocd.org/c/openocd/+/7122
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
New GCC reports 5 warning:
src/jtag/drivers/ep93xx.c: In function 'set_gonk_mode':
src/jtag/drivers/ep93xx.c:123:47: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
123 | devicecfg = *((volatile int *)(syscon + 0x80));
| ^
src/jtag/drivers/ep93xx.c:124:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
124 | *((volatile int *)(syscon + 0xc0)) = 0xaa;
| ^
src/jtag/drivers/ep93xx.c:125:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
125 | *((volatile int *)(syscon + 0x80)) = devicecfg | 0x08000000;
| ^
src/jtag/drivers/ep93xx.c: In function 'ep93xx_init':
src/jtag/drivers/ep93xx.c:182:46: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
182 | gpio_data_register = gpio_controller + 0x08;
| ^
src/jtag/drivers/ep93xx.c:183:56: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
183 | gpio_data_direction_register = gpio_controller + 0x18;
| ^
Change pointer type to allow pointer arithmetic.
Change-Id: Idd78a7156bdf99df2624043e924b8e54a0588ace
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7180
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change") replaces the jimtcl command "expr" with an openocd
version that detects the TCL syntax change and prints a warning.
The openocd "expr" command will be dropped after v0.12.0,
One side effect is that openocd invokes polling the target after
every openocd command, causing scripts that use several "expr"
commands to run much slower; see [1].
The proper fix would require openocd to invoke polling only at the
time period deadline, instead of at each command. Such fix is too
risky to be applied now, due to short time before v0.12.0-rc1.
As a temporarily workaround, let openocd to detect the "expr"
command and skip the polling.
This will be dropped together with the openocd "expr" command.
Change-Id: I8151aa28694817001046165a15475d64896f985e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/362/ [1]
Fixes: c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr' syntax change")
Reviewed-on: https://review.openocd.org/c/openocd/+/7174
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not used outside the file should not be exported
and should be declared as static.
Change-Id: Icbe7f7bce287b903edec9dc9db3370722c51fbd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7173
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Variables should not be declared in the include file, otherwise
multiple include will cause multiple instances.
Move the declaration in the C file and make it static.
Change-Id: I8b4884cba643a792a78df4e123aa324b19d92279
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7172
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Move the existing comments to the static declarations.
Change-Id: Idf208e3fda4b3f8df789553cf03ebf5f20d811bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7170
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I6a059080bbba9b3559d26c641b217be8be3b199e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7169
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I2475524f4c14520e3163572560f4a9f276356ed5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7168
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not exported should be declared as static.
Change-Id: Ieb627f7f896e4663b0d5b18c4ab1853b39d23d03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7167
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: Ie3bd17535c8cb2a0fec5d3bedfe7de3e0a702613
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7166
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Symbols that are not exported should be declared as static.
Change-Id: I6224ae89ebda3230dfee2413e3823be9b8716bba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7165
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The function set_log_output() has never been used after the drop
of eCos build with commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") in 2012.
Drop it!
Change-Id: I070b688061776c7ced5db18f738d78a4a7623726
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7164
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For some configurations, notably on DAP systems, resolve issue where single-stepping does not always transition into the HALTED state.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I053f4eaffad8c3228878ba87580ada640e4bd2fe
Reviewed-on: https://review.openocd.org/c/openocd/+/7150
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Enable ADIv5 DAP systems via JTAG or SWD transport
- Select correct PWRCTL/PWRSTAT bits for XDM/APB
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I5894210c804f85075da868d0cfc6fb20b589d99f
Reviewed-on: https://review.openocd.org/c/openocd/+/7144
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We have left the camelcase symbols *xPSR* for some time, to avoid
any conflict with possibly pending patches in gerrit.
With the approaching v0.12.0-rc1, it's time to revisit it.
The patches in gerrit that conflict with this rename are all not
merge-able due to conflicts or due to negative review.
Drop these CamelCase symbols.
Change-Id: Ifbac4c1df9cc55994e024971a2aaebeed2ea4ed3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the help of checkpatch, some CamelCase symbol passed
through the filter of maintainer's review.
Drop them.
Change-Id: If5fb07b2ffb89e853dd2a61f20d4134aa6e20d24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 48f267d4ad ("flash/stm32l4x: avoid using magic numbers for device ids")
Fixes: 5ab74bde06 ("semihosting: User defined operation, Tcl command exec on host")
Reviewed-on: https://review.openocd.org/c/openocd/+/7154
Tested-by: jenkins
Otherwise OpenOCD simply doesn't work without giving any indication why.
Change-Id: I21703fc1a0d9bed2f59da95f8a8395fe139484a4
Signed-off-by: Tim Newsome <tim@sifive.com>
* Don't read dmcontrol to set hartsel
We already know what dmcontrol should be. This addresses a long-standing
TODO. In a toy test, this reduced the number of scans by 10+%. (Most of
those are probably in poll(), so don't actually affect perceived
performance.)
Change-Id: I18e5ca391f0f5fb35f30d44dfef834e5a66aee20
Signed-off-by: Tim Newsome <tim@sifive.com>
* Make code easier to read
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Use indirect enum IDs to access XDM registers in preparation for supporting both NAR (JTAG) and APB (DAP). No new clang static analysis warnings.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I0b742fe4661ff3cf609454b8650493d141a1e1ff
Reviewed-on: https://review.openocd.org/c/openocd/+/7143
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As a follow-up of talks between JEDEC and STMicroelectronics,
JEDEC agrees to let OpenOCD project including the manufacturer's
identification code list extracted from JEDEC JEP106 document and
to let OpenOCD being updated regularly using the future JEDEC
JEP106 document versions. JEDEC requires OpenOCD to report the
origin of the JEDEC JEP106 manufacturer's identification code list
together with the JEDEC copyright.
As agreed with JEDEC, add in the file jep106.inc:
- the SPDX tag with the GPL license of the OpenOCD project;
- the JEDEC copyright;
- the text provided by JEDEC reporting the origin of the JEDEC
JEP106 manufacturer's identification code list.
While there:
- add a line reporting the version of the JEP106 document that was
used for the current code list extraction;
- remove the obsolete comment, as the script for extraction is not
working anymore; keep the script as example.
Change-Id: Iaa76716db14e15ffca04fcf7d8c27bb85a27ba10
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The full text of the license is already available in the file
LICENSES/preferred/BSD-2-Clause
and there is no need to replicate it in the source code.
Remove the BSD-2-Clause boilerplate but, preserved the copyright
notice because it provides the info on the copyright holder.
Change-Id: I162aa4ad06b551f1a71a28d049cb797ee8ab5a01
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7146
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
In the app-trace module we are polling the target in the while loops
outside of the server.c
In that loops, we need to catch ctrl+c signal by checking shutdown_openocd
status
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Id87c709a01470bf6d3642078b160a68ca85f4406
Reviewed-on: https://review.openocd.org/c/openocd/+/7142
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested with an PLUS-F5270 board which uses the MM32F5277E9PV.
Signed-off-by: iysheng <iyysheng@gmail.com>
Change-Id: Icb75ae8337fdc6fa60e39d3d74dd8bc163707bdd
Reviewed-on: https://review.openocd.org/c/openocd/+/7136
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It was a left-over from `-rtos riscv` and isn't used.
Change-Id: Ie7e380600cd1331c6d382f654474270efad9f127
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
kinetis.c:994:61: error: '%u' directive output may be truncated
writing between 1 and 10 bytes into a region of size 4
[-Werror=format-truncation=]
tested with scan-build-14
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I72d141a3f8e19ca3596beee2be8434fc8492946f
Reviewed-on: https://review.openocd.org/c/openocd/+/7140
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Scan-build of target/xtensa/ has no clang analyzer warnings from xtensa source files.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I11a125c923ece9a6fd0d9ee1698f742f88ee5cab
Reviewed-on: https://review.openocd.org/c/openocd/+/7141
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it rename misleading write_algorithm_sp to write_algorithm_stack
and change messages referring 'stack pointer' instead of stack.
No functional change.
Change-Id: Ibb9897d3f01734812ed0f8bc8cd43b935a573f8a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7132
Tested-by: jenkins
Reviewed-by: Salvatore Giorgio Pecorino <salvatore-giorgio.pecorino@st.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
FLASH_MAX_ERROR_STR is not used since commit 815c3b3533
(merged in ~2008)
Change-Id: Ic117a2e3d22235c31dc14533b6564ebf5a13ae58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7121
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The value of struct flash_driver::command can be NULL when the
flash driver does not need to add any new command.
Remove empty command definitions.
Change-Id: I5413967d4069030234469822d24e9825425ae012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7120
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The change 6363: Call poll at a fixed interval
switched from target_call_timer_callbacks() to target_call_timer_callbacks_now().
It breaks the timing as all timers callbacks are called every time
one timer expires.
Revert this part of change and use target_call_timer_callbacks().
Fixes: db16b3dc5b (Call poll at a fixed interval.)
Change-Id: Ib5b7774de9694d40c55d2a4109d0d1582fc5008b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7118
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since commit 88f429ead0
5321: target/cortex_m: faster reading of all CPU registers
debugging with a kitprog adapter freezes at debug entry.
How to replicate:
openocd -f interface/kitprog.cfg -f target/psoc4.cfg
Connect to telnet server.
Make sure the target is running:
resume
Halt the target:
halt
Without this patch OpenOCD freezes in kitprog_hid_command()
in library call hid_write().
Reduce the number of SWD transactions sent in one USB bulk write
as a workaround, simply use shorter buffer.
For details see the comment in src/jtag/drivers/kitprog.c
Change-Id: I0116894d5ebf1655f6011f0d35acdbbc178cd48c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7107
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When printing memory sizes standard ISO 80000-1 prefixes should be used.
Also a space should be added between any number and its unit according
to papers publication rules.
Change-Id: Id1d35e210766b55c201de4e80ac165d8d0414d0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Hopefully this will be the final version.
Change-Id: Ib2f8cd6f613c5e0f8e8bf7a16c3edbf2d9b439b2
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
See https://github.com/riscv/riscv-opcodes/pull/139
Change-Id: I77ae5ab369e6cde26ad44d177dcae38c0fbe08ef
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Fix Unused code Dead assignment at line 657
Fix Memory error Double free at line 2851
Fix Memory error Memory leak at line 2530
Fix error: 'a3' may be used uninitialized at line 758
Fix error: '%04x' directive writing between 4 and 8 bytes
into a region of size 5 at line 2471
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0382a622bc7c4108a335fd741816577e79240397
Reviewed-on: https://review.openocd.org/c/openocd/+/7137
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Also used type helper (PRId64) to specify format of int64_t
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I594863eab594aff621c26fefcc69a1872e9730ee
Reviewed-on: https://review.openocd.org/c/openocd/+/7111
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Now we get the license comment on the first line, which is required.
Change-Id: I54414db3c89ee6027e159ce9348459bc923b8595
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Some files have author info some doesn't. For the consistency we removed all.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie6f1ec012302e3a954c75c5106f12820722cb715
Reviewed-on: https://review.openocd.org/c/openocd/+/7104
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Change-Id: I9466edd2f43791e64f2dce719957c67728f3ec06
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Most adapters define their own commands to obtain the GPIO number and
other GPIO configuration information such as chip number, output drive
type, active high/low.
Define a general command 'adapter gpio' as replacement for the
driver-specific ones.
Change-Id: I1ca9ca94f0c7df5713172e9f62ffb0ad64e9ee97
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6967
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The S_RESET_ST sticky bit is reset after DHCSR read.
It is set at power-on reset and keeps active until the debuger reads DHCSR.
Ignore S_RESET_ST at the very first read after OpenOCD start
and suppress possibly misleading message "external reset detected"
if we cannot guarantee the reset happened recently.
While on it add a TODO comment.
Change-Id: I15217c2ca6f69ac97aff8be86bce67cba94a42cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7109
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide a customizable hook for handling target-specific GDB queries
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I684a259ed29f3651cbce668101cff421e522f79e
Reviewed-on: https://review.openocd.org/c/openocd/+/7082
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add additional error handling for targets where gaps may exist in reg_list[]
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I65232429e2de08f5d54eeca53aea0db8ce2b58af
Reviewed-on: https://review.openocd.org/c/openocd/+/7103
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'init' causes the execution of few lower level
commands, e.g. 'target init', and switches from command mode
COMMAND_CONFIG to COMMAND_EXEC, with an intermediate switch back
to mode COMMAND_CONFIG.
A timed target polling can occur during the execution of 'init'
and the target's status can trigger the execution of some events.
E.g. if a target has been left halted by a previous execution of
OpenOCD, the first poll will find the target halted, calling the
corresponding 'halted' event.
The event handler can use commands that can only be executed in
mode COMMAND_EXEC. If the poll happens while OpenOCD is in mode
COMMAND_CONFIG, the triggered handler will fail.
Prevent the target polling to operate during the execution of the
'init' command.
Change-Id: Ia435a5d2039be9b247e2336616dab53ed5d983ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7007
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The same flag 'jtag_poll' is currently used as local data for the
command 'poll' and to temporarily mask the target polling.
This can cause unexpected behavior if the command 'poll' is
executed while polling is temporarily masked.
Add a new flag 'jtag_poll_en' to hold the temporarily mask
condition and keep 'jtag_poll' for the 'poll' command only.
While there, change the initial assignment of 'jtag_poll' using
the proper boolean value.
Change-Id: I18dcf7c65b07aefadf046caaa2fcd2d74fa6fbae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB remote serial protocol specifies breakpoint/watchpoint packet
responses can be an empty string to indicate the specified breakpoint
type is not supported. Add support for this response alongside existing
"OK", "E NN" replies.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iaf6280e4c936eb95a92bc80cc74d451ebb328dc3
Reviewed-on: https://review.openocd.org/c/openocd/+/7102
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After a certain RTOS has been configured there is no mechanism
to go back to no RTOS support. It may be useful for debugging
purposes. With the provided modification, the "none" option
of RTOS is provided as a valid option.
It has been tested in two different board (Cortex M4 and Cortex M33).
Documentation has also been updated.
Signed-off-by: Asier Llano <allano@hubbell.com>
Change-Id: I602210bff31ccadd41c41e9454c52b5fffa1671e
Reviewed-on: https://review.openocd.org/c/openocd/+/7092
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This one doesn't have the license in there, which means now it's
acceptable to GPLv2 again.
See https://github.com/riscv/riscv-openocd/pull/711
Change-Id: I8ba27801172ffa955470d2627fa656cad282ee99
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7087
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tcl commands 'arm reg', 'arm mcr/mrc' do not work on M-profile based devices.
Isolate them from 'arm core_state' and 'arm disassemble' and do not chain
them from armv7m_command_handlers.
Change-Id: I2c6befdf82575e95cf05ed158ab5e6faa1a182c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7101
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tcl command 'arm core_state' was exposed even on Cortex-M devices.
However it returned message "Unsupported Command" without error status
on such device.
Set the only possible arm->core_state ARM_STATE_THUMB in armv7m init.
Block setting core_state to arm on Cortex-M.
Change-Id: I9525553ac8863a6cf77bbacbcd57e354b6cfe1ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7100
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If a Cortex-M MCU become unresponsive during a debug session and
re-examination fails to find MEM-AP, debug_ap pointer is set to NULL.
Eventual call of cortex_m_poll() dereferences debug_ap.
Check debug_ap validity at the begin of cortex_m_poll().
Change-Id: I9519f48760c91a48a9e5e8c34634d247098cb14a
Fixes: 35a503b08d (arm_adi_v5: add ap refcount and add get/put around ap use)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Just a cosmetic refactoring.
Change-Id: I7fbc05324e346fafc98d1b42691d33d3d8fbd04e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7003
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
AARCH64_COMMON_MAGIC was same as CORTEX_A_COMMON_MAGIC, probably copy pasta.
Define unique AARCH64_COMMON_MAGIC
Change-Id: Ie30e0028453a1fce5624ecad9bf73d5ac3791281
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6997
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Unify common_magic type to unsigned int
Move common_magic to be the first member of the struct
Add unsigned specifier to xxx_COMMON_MAGIC #defines
Change-Id: If961d33232698529514ba3720e04418baf6dc6fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6996
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The flash/nor subsystem uses bus_width and chip_width for CFI
external flash only. Drop setting these values for internal flash.
Change-Id: I64e79ab38b6e39e845ff96fbf4f60145e3b9690a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7098
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The working area allocation routines use 4 byte word alignment.
In the corner case the size of the working area is not aligned,
target_alloc_working_area() of size = target_get_working_area_avail()
will fail because the size gets aligned up and does not fit to the area
which size is aligned down.
Align down the result of target_get_working_area_avail() to cope with that
corner case.
While on it use fancy ALIGN_... macros instead of bitwise and operator.
Change-Id: Ia2a1e861c401c2c78fe6323379a3776fb4f47b06
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7096
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Kinetis 100 MHz rev 1.x devices have no SMC and hence need different
checking of the run mode. Details about the differences between rev 1.x
and 2.x of the Kinetis 100 MHz series can be found here:
https://www.nxp.com.cn/docs/en/application-note/AN4445.pdf
Signed-off-by: Martin Hierholzer <martin.hierholzer@desy.de>
Change-Id: Ib705385a931275159bdae9b31caecc6ec9c0da1e
Reviewed-on: https://review.openocd.org/c/openocd/+/7015
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Previously, if the target was halted before the FreeRTOS scheduler was
started but after at least one thread was created, then the current thread
would be set to whichever thread had the highest priority. In addition to
being misleading, because that thread is not actually running, it can
cause issues with gdb. For instance, breaking somewhere before the first
thread is created will show the current execution as the current thread,
but stepping over a line that creates a thread will cause the current
thread to switch to the newly created thread and the current execution to
disappear. The sudden disappearance of the current execution thread seems
to confuse some versions of gdb.
With this change, the value of xSchedulerRunning is checked to determine
whether the scheduler has been started. If it hasn't, then a fake
'current execution' thread is always created and made the current thread.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: Ide0fe7d9ffb9fac95cee4c805735f434c7c4934d
Reviewed-on: https://review.openocd.org/c/openocd/+/6935
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When there are no rtos threads or none are active, a fake thread with
ID 1 is created for the current execution, but the current thread ID was
never set to this new fake ID. This would lead to an incorrect attempt to
read stacked registers for this fake thread. Explicitly setting the
current thread ID to the fake ID ensures that the registers are read from
the core instead of calling freertos_get_thread_reg_list.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I694509a0e01df089429b20ff1b879fc0592b532d
Reviewed-on: https://review.openocd.org/c/openocd/+/6934
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If range's upper bound was equal to 2^64 or the range was wrapping around 0
(which is perfectly legal), writes were not performed due to riscv_addr_t
overflow.
Make the main RISC-V structure more compliant with OpenOCD coding style.
Other typedefs remains as is.
Change-Id: I5657ad28fea8108fd66ab27b2dfe1c868dc5805b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6998
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
We found that the NPCX has an issue with the byte lanes so that non byte
aligned writes aren't working. To overcome this, for byte accesses we
copy the byte to be written to all of the byte lanes.
doc: Document command nu_npcx_quirks
Signed-off-by: benjbender <benjbender@gmail.com>
[Andreas Fritiofson: Squashed commits]
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I9ef63bf692f4e68f57459e1ec33f3abcbf533cd2
Reviewed-on: https://review.openocd.org/c/openocd/+/6630
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for DAP interface to Cadence vdebug driver.
It implements a new transport layer for dapdirect_swd.
Change-Id: I64b02a9e1ce91e552e07fca692879655496f88b6
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6965
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit b8e18d292e ("helper/jim-nvp: comply with coding style
[1/2]") tags as deprecated the old CamelCase API of jim-nvp, so
that old patches already in gerrit or in user's local git can
still build while dumping a deprecated message.
So far, we have not found any such case, so the deprecated API can
be safely dropped in preparation of v0.12.0-rc1.
Drop the compile flag "-Wno-error=deprecated-declarations" and the
deprecated API.
Change-Id: I52ce47eda69a51c2dd29aac15f16e285492d89b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7052
Tested-by: jenkins
With most of the files already processed through scripts, replace
manually the license to the few remaining files.
Change-Id: I3c7131e66b89ddad482f1074b5be5a9a69fdf6fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7073
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I30cd66ac7d737f1973c68fdbb841ffcf00e917c4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7072
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: If0194089baded7f58dc5d87a35d6e0aff9f43785
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7070
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ie873d12bb0fb838d0d6252e6b9ca3c2118853e9a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7069
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I7851617e2682f97ccc3927e3941aadef2df63b54
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7068
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ic7db91fe37d1139d42c99e303b3243b6c8fe3ea2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7067
Tested-by: jenkins
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line in specific format.
Move the SPDX tag to the first line and fix it where needed.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ie9a05f530009d482a4116eebd147fd7e1ee3d41e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7066
Tested-by: jenkins
Use the standard SPDX tag, where it was incorrectly applied.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Iaec63abc6e0a38e5b0ae0ea7f5ecee7ca007bbbd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7065
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
Change-Id: I29f51caa5ae9854d05ce7e150d168a7002607cd1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7064
Tested-by: jenkins
Few files have the FSF boilerplate without the latest statement on
where to get the GPL license.
Manually replace the FSF boilerplate with the SPDX tag.
While there, reorganize the copyright statement.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I0c908d01c010e24f9c7e94885e7fbed4ecf26a86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7063
Tested-by: jenkins
Add the new license text in the license pool.
Replace the GPL and BSD boilerplates with the SPDX tag.
Add the copyright owner of Atmel, as it was explicitly listed in
the BSD boilerplate text.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ibb117dbf8402269be3e5ba4f4c472162494d813f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7062
Tested-by: jenkins
Add the license exception text in the license pool.
Add the exception chapter in license-rules.txt
Replace the boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ied513b7c9c0722ed2a9c11dbdff3fbf59f1b41ce
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7061
Tested-by: jenkins
Add the license text in the license pool.
Replace the BSD boilerplate with the SPDX tag.
Add the copyright owner of Jim Project, as it was explicitly
listed in the boilerplate text.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I6dd004b1945773c10539016ce733d1fbfe776a9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7060
Tested-by: jenkins
Replace the BSD boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I5a8cab2051eee7eb99adf67f9631b0827c1359de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7059
Tested-by: jenkins
Some file miss completely the license tag.
Add the SPDX tag, using the same GPL-2.0-or-later license of the
OpenOCD project.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I1fb51e722232d14f050458a820c3041de3dc9138
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7058
Tested-by: jenkins
SPDX tag is replacing the FSF boilerplate.
For files that have both, remove the FSF boilerplate and keep only
the SPDX tag.
Change-Id: I04c4764d13d4ca92453f30ed16aeae53cd4c3fc8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7057
Tested-by: jenkins
Add the SPDX tag to makefiles, configuration scripts and tcl files
present in the folders under src/
Change-Id: I1e4552aafe46ef4893d510da9d732c5f181784a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7051
Tested-by: jenkins
This one doesn't have the license in there, which means now it's
acceptable to GPLv2 again.
Change-Id: I8ba27801172ffa955470d2627fa656cad282ee99
Signed-off-by: Tim Newsome <tim@sifive.com>
This gets us the new license header, which was requested upstream.
Change-Id: I992b4f3bb230edb9f281e2278dd41c712098ed4c
Signed-off-by: Tim Newsome <tim@sifive.com>
ARM/RISC-V semihosting calls SYS_READ/SYS_WRITE require
inversion of the result value as described in
"Semihosting for AArch32 and AArch64". Prior to
this patch, this was done correctly only if
(semihosting->is_fileio==false).
This patch has been tested with STM32F446.
Change-Id: I1b34c8d8393f7dfa66ee6539904a2eaf8f9154b0
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/232/
Reviewed-on: https://review.openocd.org/c/openocd/+/6803
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable 'smp_break' is only set and used in case of smp.
But clang cannot track if 'target->smp' get modified between the
set and the use of 'smp_break', so it consider possible to use
'smp_break' uninitialized.
Initialize 'smp_break' to silent clang.
Change-Id: Ifa25a84fe9ffa25b8b58d7920ec77994c3b7ebfe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 77287b8d47 ("target: add Espressif ESP32 basic support")
Reviewed-on: https://review.openocd.org/c/openocd/+/7050
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
These enum values are useful for the arch level semihosting call handlers.
Currently riscv uses them, we also need similar return codes for the xtensa.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I8f63749cc203c59b07862f33edf3c393cd7e33a9
Reviewed-on: https://review.openocd.org/c/openocd/+/7039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This driver is used with the ESP32 chips which has builtin USB-JTAG
interface. e.g. with ESP32-C3, ESP32-S3
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61
Reviewed-on: https://review.openocd.org/c/openocd/+/6943
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
New mingw compiler correctly complains for using a freed memory
area:
src/helper/configuration.c: In function 'get_home_dir':
src/helper/configuration.c:182:29: error: dangling pointer 'home'
to 'homepath' may be used [-Werror=dangling-pointer=]
182 | home_path = alloc_printf("%s/%s", home, append_path);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In fact the variable 'homepath' is declared inside an 'if' branch
and is not available outside.
Move the declaration of 'homepath' to have it available in a wider
context.
Change-Id: I4a43a03c007c9f0d5c4cee962a9f7cc83ca49637
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Dietmar May <dietmar.may@outlook.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7038
Tested-by: jenkins
Reviewed-by: Dietmar May <dietmar.may@outlook.com>
Commit b9526f1401 ("semihosting: permit redirection of
semihosting I/O to TCP") introduces a new comparison with NULL.
Remove it.
Change-Id: Ice4333c50d16f7592f0ff86b1640217fa42e34f6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: b9526f1401 ("semihosting: permit redirection of semihosting I/O to TCP")
Reviewed-on: https://review.openocd.org/c/openocd/+/7031
Tested-by: jenkins
We already have a helper to release the gpio.
Extend it to also release its corresponding gpio chip.
As side effect, remove comparison with NULL.
Change-Id: I47cd446edfaead662d63c3330f25a791b747e882
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7033
Tested-by: jenkins
Reviewed-by: Steve Marple <stevemarple@googlemail.com>
Commit 20adf85f34 ("linuxgpiod: add SWDIO buffer") introduces an
additional gpio for SWDIO direction, but does not release it at
driver's exit.
Release the gpio at exit.
Change-Id: If7ea31f79ffed04af585864e49bcf1f35e118bdd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7032
Tested-by: jenkins
Reviewed-by: Steve Marple <stevemarple@googlemail.com>
Commit 6c0151623c ("aarch64: add support for "reset halt"")
introduces the register setting to halt at reset vector, but:
- does not consider the case 'srst_pulls_trst' that makes useless
setting the registers as they will be erased by the pulled trst;
- does not clean sticky errors in case of 'srst_gates_jtag'.
Avoid any register initialization on 'srst_pulls_trst' and move
the cleaning of sticky errors in the common block.
Change-Id: I6f839f06f7b091e234ede31ec18096e51f017bcd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 6c0151623c ("aarch64: add support for "reset halt"")
Reviewed-on: https://review.openocd.org/c/openocd/+/7034
Tested-by: jenkins
Reviewed-by: Christian Hoff <christian.hoff@advantest.com>
Custom user syscalls can be handled with target events in the TCL scripts.
This patch gives another opportunity to handle custom syscalls in the c files.
Besides that some utility functions are also exported for the custom handlers.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ice13d527540a0de0b2a8abda912ae3dcff3834b7
Reviewed-on: https://review.openocd.org/c/openocd/+/6889
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Arm "CoreSight System-on-Chip SoC-600" specification describes a
bridge "Access Port v1 adapter" aimed to "connect a legacy Access
Port (AP) ... into an CoreSight Architecture v3 system".
A ROM table can be located in the "legacy" part of the system,
on the legacy AP behind the APv1 adapter.
For the purpose of scanning the ROM tables, consider an ADIv6
SoC-600 APv1 adapter as an ADIv5 AP.
Change-Id: I97d42fb77013c1251fb68d0caa4274086bf38a70
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6827
Tested-by: jenkins
Configuration file can specify, as target's debug AP, an AP that
contains a ROM table that points, in turn, to other APs.
Current code in cortex_a and aarch64 is not able to handle a
return from dap_lookup_cs_component() that points to another AP.
While it could be interesting to specify 'root' as target's debug
AP, drop any found value if it's not in the starting AP.
Change-Id: Id206e4fa7a29e9402c8e2393026817b410bbb8bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6826
Tested-by: jenkins
ADIv6 adds AP that only contain a ROM table in the AP itself, that
can point to other AP containing either another AP level ROM table
or a MEM-AP to be parsed as usual.
Add support for parsing AP level ROM tables.
Change-Id: Ic25863b16463b8a6adc3b15e26db7fdca858d6df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6467
Tested-by: jenkins
ADIv6 adds AP that only contain a ROM table in the AP itself, that
can point to other AP containing either another AP level ROM table
or a MEM-AP to be parsed as usual.
To handle recursive AP access, reorganize the code to:
- pass the depth==0 from the command 'dap info';
- print the AP number as first line, adding proper indentation on
depth>0;
- align the following print with proper indentation.
Change-Id: I5b811810c807fc51b307bd60f67817d9de2aa095
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6466
Tested-by: jenkins
On ADIv6 the system root ROM table is found by reading the DAP DP
registers BASEPTR0 and BASEPTR1.
Add option 'root' to the commands 'dap info' to let it retrieve
the system root ROM table's AP from DAP DP, then use such AP for
following dump.
Change-Id: I1789457a005faa3870c5d14f763378d2f6a5f095
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6462
Tested-by: jenkins
ADIv5 DAP can only have 256 AP, while ADIv6 can provide till
2**40 (1,099,511,627,776) AP per DAP.
Reuse the field ap_num in struct adiv5_ap, currently used on ADIv5
to hold the ADIv5 AP number (apsel), to contain the ADIv6 AP base
address.
Convert struct adiv5_ap->ap_num to 64 bit and initialize it to
DP_APSEL_INVALID for unused AP.
Restrict dap_find_get_ap() to ADIv5 only. To be enhanced.
On ADIv6, let dap_get_ap() return an already allocated AP, or
allocate and return an unused AP.
Add function is_ap_num_valid() and use it.
Change-Id: Ib2fe8c7ec0d08393cd91c29fdac5d632dfc1e438
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6461
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Tested-by: jenkins
During enter in SWD read DP_DPIDR without selecting the register
bank through DP_SELECT_DPBANK.
Handle the different format of DP_SELECT register.
Change-Id: Iea1b8eb6ec94177e16a430d5885595a38e833eeb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6697
Tested-by: jenkins
ADIv5 reports:
Accessing AP registers or debug resources in connected
device through an AP can be subjected to other variable
response delays in the system. A debugger that can adapt
to these delays and avoid wasting WAIT scans operates more
efficiently and provides higher maximum data throughput.
The existing code in OpenOCD uses extra tck only for accessing
resources through an AP.
Extend the use of extra tck also for accessing an AP register.
Split from change https://review.openocd.org/6077/
Change-Id: I2082362e098d09f4ba0668e01f5196afc965c8f3
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6460
Tested-by: jenkins
swd and dap-direct are not implemented yet
Split from change https://review.openocd.org/6077/
Change-Id: I6d73d8adf6a6090001c5d4771325fb1d63c45e3c
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6459
Tested-by: jenkins
By accessing invalid AP in JTAG mode, it's possible to trigger the
error:
JTAG-DP STICKY ERROR
After that the sticky error is never cleared and the whole DAP
gets not anymore accessible.
Clean-up the sticky error once detected.
Change-Id: I8b07263b30f9e46645f0c29084b8f1626e241f45
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6430
Tested-by: jenkins
Required for parsing ADIv6 ROM tables.
Split from change https://review.openocd.org/6077/
Change-Id: I849543b7b4a4455b10bd9fc7da38a37849d71700
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6458
Tested-by: jenkins
ADIv5 MEM-AP registers are a subset of ADIv6 MEM-AP registers and
are located at different offset.
To prepare for introducing ADIv6, add 'struct adiv5_dap *' as
argument to ADIv5 registers macro.
Check the ADI version and use the proper address.
Both adapter drivers rshim and stlink are ADIv5 only, so let them
use the ADIv5 macros only.
Split from change https://review.openocd.org/6077/
Change-Id: Ib861ddcdab74637b2082cc9f2612dea0007d77b1
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6457
Tested-by: jenkins
Add flags to 'dap create' command and set the field adi_version
in struct adiv5_dap.
Actually only ADIv5 is functional. Other patches are needed to get
ADIv6 working.
Split from change https://review.openocd.org/6077/
Change-Id: I63d3902f99a7f139c15ee4e07c19eae9ed4534b9
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6456
Tested-by: jenkins
While an ADIv5 DAP can only have 256 AP, ADIv6 can provide till
2**40 (1,099,511,627,776) AP per DAP.
The actual trivial code implementation for ADIv5 (that uses an
array of 256 ap in the struct adiv5_dap) cannot be extended as-is
to handle ADIv6.
The simple array of 256 AP can be reused as a dynamic storage for
ADIv6 ap:
- the ADIv5 AP number is replaced by the ADIv6 base address;
- the index of the array (equal to ADIv5 AP number) has no link to
any ADIv6 property;
- the ADIv6 base_address has to be searched in the array of AP.
The 256 elements in the AP array should be enough for any device
available today. In future it can be easily increased, if needed.
To efficiently use the 256 elements in the AP array, the code
should associate one element of the array to an ADIv6 AP (through
the AP base address), then cancel the association when the AP is
not anymore needed. This is important to avoid saturating the AP
array while exploring the device through 'dap apreg' commands.
Add a reference counter in the struct adiv5_ap to track how many
times the struct has been associated with the same base address.
Introduce the function dap_get_ap() to associate and return the
struct, and dap_put_ap() to release the struct. For the moment the
code covers ADIv5 only, so the association is through the index.
Use the two functions above and dap_find_get_ap() throughout the
code.
Check the return value of dap_get_ap(). It is always not NULL in
the current ADIv5-only implementation, but can be NULL for ADIv6
when there are no more available AP in the array.
Instrument dap_queue_ap_read() and dap_queue_ap_write() to log an
error message if the AP has reference counter zero, meaning that
the AP has not been 'get' yet. This helps identifying AP used
without get/put, e.g. code missed by this patch, or merged later.
Instrument dap_cleanup_all() to log an error message if an AP has
reference counter not zero at openocd exit, meaning that the AP
has not been 'put' yet.
Change-Id: I98316eb42b9f3d9c9bbbb6c73b1091b53f629092
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6455
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Tested-by: jenkins
The segfault could be triggered if:
- At least one target failed to get examined (therefore does not have the
register cache set up yet),
- and "reset" TCL command was issued, which internally tries to
invalidate the register cache.
Minor cleanup: "registers_initialized" member removed from riscv_info_t
because it is not used anywhere.
Change-Id: I6288c0d4343ef6a330fb2a6b49d388e7eafa32a2
Signed-off-by: Jan Matyas <matyas@codasip.com>
There is an accsess to wrong index, when arm semihosting_basedir
command not used or basedir set to empty string.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I3afa049d74b30496f5c03ba4ef67431784f81bdc
Fixes: ce5027ab01 ("semihosting: add semihosting_basedir command")
Reviewed-on: https://review.openocd.org/c/openocd/+/7005
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In function adiv5_jim_configure() check that calloc() returns a
valid allocated memory pointer.
Change-Id: I97287e168834693900341add9d9eb9a5f38c55b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7014
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The array is partially initialized with buf_set_u32(,5,32,), then
the rest of the array is read from SWD.
But scan-build report the array to have garbage content after the
initialization, due to the offset of 5 bit that only inits part of
the first byte.
Silence the false positive from scan-build by initializing the
array.
Change-Id: Ic38d50280f67939e3ec5fa05741f66d5f993f8c2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7013
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While scan-build complains that dap_p or ap_num_p could be NULL,
the current code never passes NULL pointers.
Add an assert() to silent scan-build and prevent any further use
of the function with incorrect parameters.
Change-Id: I656810dddcea61e85d85b13efb114f7607ef837c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7012
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit d01b3d69ec ("arm_adi_v5: separate ROM table parsing from
command output [3/3]") introduces a new scan-build warning because
removing one return in case of error causes using uninitialized
values.
Add back the return on error.
Change-Id: I10ddc548b756d34aaccc0511f091b4caa5ec271a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: d01b3d69ec ("arm_adi_v5: separate ROM table parsing from command output [3/3]")
Reviewed-on: https://review.openocd.org/c/openocd/+/7011
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 21f7885d1c ("arm_adi_v5: separate ROM table parsing from
command output [1/3]") introduces a new scan-build warning because
continues the execution even when dap_get_debugbase() returns
error. The value of 'apid' can be uninitialized:
5th function call argument is an uninitialized value
Check the return value and quit on error.
While there, remove the useless initialization of 'dbgbase' that
was apparently required for the same problem.
Change-Id: Iade26a152925ee0f1bf114ed829b94f7ed5b254f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 21f7885d1c ("arm_adi_v5: separate ROM table parsing from command output [1/3]")
Reviewed-on: https://review.openocd.org/c/openocd/+/7010
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target_to_armv7m() just returns a type-cast of target->arch_info,
so the test has no value.
Following target_run_algorithm() checks magic number so
we need not worry about execution on mismatched architecture.
Change-Id: Ic9892a488a42af1d8e8731eddb39240deeb26020
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6755
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Error: Uninitialised value was created by a heap allocation
at telnet_new_connection (telnet_server.c:227)
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I698a3648be698c93a2395a718ee1ade028226995
Reviewed-on: https://review.openocd.org/c/openocd/+/7006
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix "Declared variable-length array (VLA) has zero size" warnings
while at there instrument the probe function to ensure the flash bank
contains at least 1 sector
Change-Id: I3ba0e6345881557ad1aab2d1b41eee438b49fe04
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6470
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32-S2 is a single core Xtensa chip.
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I2fb32978e801af5aa21616c581691406ad7cd6bb
Reviewed-on: https://review.openocd.org/c/openocd/+/6940
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
when using semi-hosting with cortex_a this LOG_INFO pollutes openocd
console, so just reduce the log level of this message.
Change-Id: I91aa70492f4e361b25a0e5517d0cf73f2f8ed599
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://gerrit.st.com/c/stm32ide/official/openocd/+/248225
Tested-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6993
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'flash erase_check' showed the message
'Running slow fallback erase check - add working memory'
even in the case the target didn't implement blank_check_memory.
Change return code of target_blank_check_memory() in this case
and sense it in default_flash_blank_check() and show a message
without a request for working memory.
Change-Id: I7cf9bf77742964b4f377c9ce48ca689e57d0882f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6765
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
This helps e.g. if there are 8 cores, and cores 0--3 are in one SMP
group while 4--7 are in another group. (And there are 2 gdb instances
connected, one debugging the first group, and one the second.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I7b6c9382eadf964529105eaf0411a42d48768668
Reviewed-on: https://review.openocd.org/c/openocd/+/6979
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Update debug_defines from the spec.
Now it includes constants for field values, so use them instead of
duplicating that here.
Change-Id: I2fca6e89f25123c39d4bf483b8244e47aefb0f88
* Remove unused #defines
Change-Id: Id20351851c9ed2c3aa82ccf8c04b604bef11692a
* Use debug spec constants in a few more places
Change-Id: Ic4578729c89e3c6a26a72772e1635c5345bd6a52
Signed-off-by: Tim Newsome <tim@sifive.com>
* Use macros for trigger action types.
Which were added with the very latest debug_defines.h.
Change-Id: I47f73e11d2ec529c720f2e1df05f7b0d3026e43a
Signed-off-by: Tim Newsome <tim@sifive.com>
This command allows users to set base working directory for the
semihosting I/O operations.Default is the current OpenOCD directory.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I80c5979e4c96d66cccdd12cc6fcd5f353e5c6b4d
Reviewed-on: https://review.openocd.org/c/openocd/+/6888
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes "variable set but not used" errors.
Tested with Homebrew clang version 13.0.1
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ia90baf5b4857db2b5569ebe6adbbb832de772aad
Reviewed-on: https://review.openocd.org/c/openocd/+/6971
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Removes Warning: line 6482, column 12
1st function call argument is an uninitialized value
Use target ptr directly as checked in previous lines instead of
dereferencing head->target
Change-Id: I6804b776fd493af71f3098d702f9cdc7acb50151
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6970
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Change set_haltgroup() to more general set_group()
Change-Id: Ib91a252ac63604e54b756f70c549ccd47241fd10
Signed-off-by: Tim Newsome <tim@sifive.com>
* Properly use enum.
Change-Id: I0edef6053fac388db38a22fe7557623fa93ec705
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* Style changes suggested in review.
Change-Id: I29e83d3dbef09cb971ec0355aff733191a6e4679
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Incorrect validation prevented GPIO0 from controlling the direction of
the SWDIO buffer or operating TRST/SRST.
Have all GPIO number validation checks performed by is_gpio_valid().
Change-Id: Ib8fb704ab588a618ac41c111f6168d658891d92c
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It is a common requirement to automatically execute some command
after "init".
This can be achieved, either in scripts or through OpenOCD command
line, by explicitly calling "init" followed by the commands.
But this approach fails if the request for post-init commands is
spread across configuration files; only one of the files can split
pre-init and post-init status by calling "init".
The common workaround is to "rename" the command "init" and
replace it with a TCL proc that calls the original "init" and the
post-init commands. E.g. in Zephyr script [1].
To simplify and formalize the post-init execution, use a TCL list
that contains the list of commands to be executed. Every script
can contribute adding new commands, e.g. using "lappend".
In the same way, formalize the pre-shutdown execution with a TCL
list of user commands to be executed before OpenOCD exit.
Document them and add trivial examples.
Drop from documentation the suggestion to rename "shutdown".
Change-Id: I9464fb40ccede3e7760d425873adca363b49a64f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Link: [1] https://github.com/zephyrproject-rtos/zephyr/blob/zephyr-v2.7.1/boards/arm/nucleo_h743zi/support/openocd.cfg#L15
Reviewed-on: https://review.openocd.org/c/openocd/+/6851
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function target_type::deassert_reset() is called for every
target after reset is deasserted. If the target fails to get
halted, we log a warning and issue a halt request for the target
itself.
Current code calls the generic target_halt() that:
- extends the halt to all the targets in the SMP node;
- waits for targets to halt.
This breaks the logic of running target_type::deassert_reset()
per target. Plus, waiting for targets to halt delays the call of
target_type::deassert_reset() for the next targets.
Replace the call to target_halt() with the aarch64 specific
function to halt the single target. Pass the parameter HALT_LAZY
to prevent the wait for target halted.
Similar solution is already implemented for cortex_a.
Change-Id: I446dc03cb91524c6d388db485bc2388177af77b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6947
Tested-by: jenkins
Arm documentation does not explicitly report the order of the two
32bit words that compose the 64bit value. But both ADIv5 and ADIv6
specify that only little-endian is supported (ADIv5.2 obsoletes
the big-endian support). This change reads the 64bit value in
little-endian.
Detect the 64bit content and use it.
Change-Id: I723ec099c7e8c70c1f9a568e32ea867fcbf1f1db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6465
Tested-by: jenkins
With the generic function for ROM table walk-through, reimplement
dap_lookup_cs_component().
Catch the code CORESIGHT_COMPONENT_FOUND and halt the search.
While there, drop two macros in arm_coresight.h, now unused.
Change-Id: I589ef7ae8a651d0c422ce7d0b4ed913713a8217e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6824
Tested-by: jenkins
Simplify the code in cortex_a and aarch64 by moving the call to
dap_get_debugbase() inside dap_lookup_cs_component().
This has the further effects:
- dap_get_debugbase() is not referenced outside arm_adi_v5.c and
becomes static;
- dap_lookup_cs_component() looses one parameter;
- the coreid parameter 'idx' is passed as value;
- the caller in aarch64 don't have and don't print the irrelevant
value of AP register APID;
- fixes the debug message in the caller in aarch64 to print the
coreid value instead of always zero.
Change-Id: Ic7f0f643fdf067c059c8f2455a02ff18a3fed054
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6823
Tested-by: jenkins
Now all the actions (build command output) of command "dap info"
are decoupled from the ROM walk-through.
Pass the actions as a generic parameter to ROM walk-through code.
Put as private data every information that is only required by the
actions and not by the ROM walk-through.
Change-Id: I3b6ad112ea21296458c94aebbf91bf65bf6657a7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6822
Tested-by: jenkins
Evgeniy Naydanov
Tim Newsome
Erhan Kurubas
Daniel Anselmi
Marc Schink
Mark Zhuang
Laurent LEMELE
Marek Vrbka
Parshintsev Anatoly
eolson
Chao Du
Antonio Borneo
iosabi
Jacek Wuwer
Bohdan Tymkiv
Ian Thompson
Jan Matyas
Matthijs Kooijman
Amaury Pouly
Tarek BOCHKATI
Tomas Vanek
Paul Fertser
Julien Massot
panciyan
François LEGAL
Chao Du
Kai Schmitz
Peter Collingbourne
Andrew Lalaev
Hang Xu
Anatoly Parshintsev
Jan Matyas
Andreas Bolsch
Daniel Serpell
N S
Andreas Fritiofson
Marian Buschsieweke
Jian-Hong Pan
Zale Yu
Boris-Chengbiao Zhou
Tarek BOCHKATI
Jan Matyas
Koudai Iwahori
James G. Smith
Fawaz Tirmizi
Kyle Schwarz
Marcin Niestroj
Dan Stahlke
Nima Palizban
Dolu1990
Nick Kraus
Evgeniy Naydanov
Giulio Fieramosca
Simon Smiganovski
Xiang W
Ben McMorran
Jonathan Bell
Daniel Goehring
Keith Packard
mrv96
Dmitry Ryzhov
Tim Nordell
Toms Stūrmanis
Frank Dischner
Steve Marple
Antonio Borneo
iysheng
MadSquirrel
Asier Llano
Martin Hierholzer
Ben Bender
Pavel Kirienko
Kevin Burke
Huaqi Fang
wzgpeter