Added support for the new Renesas RISC-V
device: RZ/Five
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Change-Id: Id8ba29b83528c0bfe4f9b4ed21b0151a6e853bd7
Reviewed-on: https://review.openocd.org/c/openocd/+/6974
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Added support for two new devices: RZ/G2LC and RZ/G2UL
Change-Id: Iec6ba88c1d279f50808b060343b45c796bbfdbfc
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6972
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tigard[1] is an FT2232H-based development tool designed for ease of use
with many different protocols and targets. It includes a JTAG header
wired to channel B, with labeled pins for the four required signals as
well as nTRST and nSRST, which are connected through an output buffer to
BDBUS4 and BDBUS5 respectively.
Add an interface config for Tigard. I wrote it by referencing the Tigard
schematic and tested it by debugging a couple of RISC-V development
boards.
[1] https://github.com/tigard-tools/tigard
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Change-Id: I34df9f72538ba1e40ad53b568c9cdca96ae4b082
Reviewed-on: https://review.openocd.org/c/openocd/+/6952
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added bluenrg-lps support
Added file for the board steval-idb012v1
Fixed size_info information using a mask
Changed the if condition in bluenrg-x.cfg to be valid only for bluenrg-1 and bluenrg-2
Signed-off-by: Salvatore Giorgio PECORINO <salvatore-giorgio.pecorino@st.com>
Change-Id: Ic0777ec0811ee6fac7d5e1d065c4629e47d84a1f
Reviewed-on: https://review.openocd.org/c/openocd/+/6928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The flash is compatible with stm32f1x, reuse the driver.
Extend the size of work area to RAM size of the smallest device.
Stop watchdogs before flash programming.
Change-Id: I67a7654a6e196f9d4b2409edaa7990c53334437e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6711
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested on an EFM32PG12 Starter Kit.
Change-Id: I2cbc36fe0d2ad2089bf8c1e7d2260daaae4ddbb4
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/5353
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace deprecated commands 'mem2array' and 'array2mem' with
new Tcl commands 'read_memory' and 'write_memory'.
Change-Id: I116d995995396133ca782b14cce02bd1ab917a4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6859
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the LS1046A Reference Design Board. There are
several JTAG headers accessable once the case is opened, but this config
is for the externally-accessable CMSIS DAP.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I0f83470da3758f0c4512ce47348c4db7de17b27e
Reviewed-on: https://review.openocd.org/c/openocd/+/6855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1046A is a quad-core processor from NXP in the layerscape family.
This SoC is a bit tricky to program: while the AArch64 CPUs are
little-endian, most of the peripherals are big-endian. Care must be
taken when interpreting memory reads/writes. This processor is in the
same family as the ls1012a, so the setup is similar.
If you use OpenOCD to attach early in the boot process, only the cpu0
may be available. Trying to halt other CPUs will fail. To avoid this,
defer examination of cpus 1-3, and provide a core_up helper (like e.g.
zynqmp).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: If5a1a9441fb35fea3e05dc708b42e0cb3bbf2a54
Reviewed-on: https://review.openocd.org/c/openocd/+/6854
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Original TLC syntax uses 'set varname' to retrieve the value of
variable 'varname'. Such archaic syntax is still valid, but the
shorter '$varname' makes the code easier to read.
Replace 'set varname' with '$varname'.
While there, remove some useless curly brackets.
Change-Id: I27310e8c05afe56ea8bd0e41d4ae2c34447b725c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6863
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for the latest in TI k3 family AM625 SoC.
For further details, see https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: Ia54d0eab1c30a973afb1c2c61f4c5a72d29d9b78
Reviewed-on: https://review.openocd.org/c/openocd/+/6798
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the latest in TI k3 family J721S2 SoC.
For further details, see http://www.ti.com/lit/pdf/spruj28
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I608ab4513ffb6b5c4166ba423e7d0dddbbb3bbfd
Reviewed-on: https://review.openocd.org/c/openocd/+/6796
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since we can detect the type of target as well, reuse the _cpu_no_smp_up
function name and use the target name to simplify the _up function and
maintain consistency with what we introduced for r5.
Lets introduce gdb-attach event in a much cleaner fashion.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
While at it, fix a minor type of s/are/as in "Set Default target are
core 0" and simplify the foreach usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3259b7c3ae4c71b06d921edfaefe17c03bb673dc
Reviewed-on: https://review.openocd.org/c/openocd/+/6616
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since we can detect the type of target as well, make the attach
function name generic for the follow on cleanup patch on armv8 to use
as well.
Lets introduce gdb-attach event in a much cleaner fashion. We can
introduce a simpler r5_up function since we now have more descriptive
core names making the individual descriptive procs redundant.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I31506bb2b86e63638082640eb72aa7c4c9575e93
Reviewed-on: https://review.openocd.org/c/openocd/+/6617
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
R5 targets are currently named r5.0..n and the only way for user to
determine the actual type is external documentation. Lets just rename
the target names to make them descriptive to not require external
documentation for finding which R5 to connect to.
NOTE: we leave the _mcu_r5_cores _main0_r5_cores _main1_r5_cores alone
for now to allow existing startup proc functions to work, but we will
drop it in the follow on patch.
Previously:
Info : starting gdb server for j721e.cpu.r5.0 on 3336
Info : Listening on port 3336 for gdb connections
Info : starting gdb server for j721e.cpu.r5.1 on 3337
Info : Listening on port 3337 for gdb connections
Info : starting gdb server for j721e.cpu.r5.2 on 3338
Info : Listening on port 3338 for gdb connections
Info : starting gdb server for j721e.cpu.r5.3 on 3339
Info : Listening on port 3339 for gdb connections
Info : starting gdb server for j721e.cpu.r5.4 on 3340
Info : Listening on port 3340 for gdb connections
Info : starting gdb server for j721e.cpu.r5.5 on 3341
Info : Listening on port 3341 for gdb connections
With this patch:
Info : starting gdb server for j721e.cpu.mcu_r5.0 on 3336
Info : Listening on port 3336 for gdb connections
Info : starting gdb server for j721e.cpu.mcu_r5.1 on 3337
Info : Listening on port 3337 for gdb connections
Info : starting gdb server for j721e.cpu.main0_r5.0 on 3338
Info : Listening on port 3338 for gdb connections
Info : starting gdb server for j721e.cpu.main0_r5.1 on 3339
Info : Listening on port 3339 for gdb connections
Info : starting gdb server for j721e.cpu.main1_r5.0 on 3340
Info : Listening on port 3340 for gdb connections
Info : starting gdb server for j721e.cpu.main1_r5.1 on 3341
Info : Listening on port 3341 for gdb connections
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2989efe3ae3e16754f98fa1dc9363ec4c898f7c3
Reviewed-on: https://review.openocd.org/c/openocd/+/6627
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The MCU is present on few of the SoCs and is meant as General Purpose
(GP) MCU of the system. Lets rename it to make clear what we are
debugging - esp when multiple MCUs are present in the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I16132d321daf6e9b1d893fe6f92026d5aa9eb152
Reviewed-on: https://review.openocd.org/c/openocd/+/6619
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The M3 is the system controller of the system. Lets rename it to make
clear what we are debugging - esp when multiple MCUs are present in the
system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I4cd03b6068b8ce140fd254f9dd88151c4c7006d7
Reviewed-on: https://review.openocd.org/c/openocd/+/6618
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add gdb-attach event to call the "up" function of m3 and m4 allowing for
more seamless integration with gdb for end users. We still retain _up
functions for non-gdb functionality.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Suggested-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2e51fdbd8756f156551e589c748c3a338afa655c
Reviewed-on: https://review.openocd.org/c/openocd/+/6615
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
both stm32l5x and stm32u5x configs are almost identical except
clock config.
while at there rename target procs to avoid issues with JTAG daisy
chaining.
Change-Id: Ibbb1dfeb91a7f8d5d45744cf57dca2877f60e0c5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6596
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds some additional IDCODEs from the datasheet. It also adds
support for customizing the tap name.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I7cda10b92c229b61836c12cd9ca410de358ede2e
Reviewed-on: https://review.openocd.org/c/openocd/+/6846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Changed flash driver to support writing to the user data page, as well as to any portion of the lockbits page above 512 bytes (the amount used for the actual page lock words). The top part of the lockbits page is used on at least the EFR32xG1 chips for the SiLabs bootloader encryption keys.
As presented to the user, the lockbits page is the same size as the other pages, but any attempt to write to its low 512 bytes is an error. To enforce this, efr32x_write is renamed to efm32x_priv_write and a wrapper function is provided in its place. If the user erases the lockbits page, the driver rewrites the cached lock words after the erase. When the driver erases the lockbits page in order to update the lock words, it first takes a copy of anything stored in the top part of the page, and re-programs it after the erase operation.
There are now multiple instances of flash_bank for each target, and the flash_bank instances must share their cached lock words to operate as intended. Therefore, when a bank is created, the global flash bank list is used to find any other banks that share the same target. Since some banks in the global list are invalid at the time free_driver_priv is called, reference counting is used to decide when to free driver_priv.
To avoid the need to find the lockbits flash_bank from another flash_bank, efm32x_priv_write and efm32x_erase_page now take an absolute address.
There didn't seem to be any reason to prohibit unprotecting individual flash pages, so that limitation is removed from efm32x_protect().
This addresses ticket #185.
Valgrind-clean, except for 2x 4kiB not freed/still reachable blocks that were allocated by libudev.
No new Clang analyzer warnings, no new sanitizer warnings.
Signed-off-by: Doug Brunner <doug.a.brunner@gmail.com>
Change-Id: Ifb22e6149939d893f386706e99b928691ec1d41b
Reviewed-on: https://review.openocd.org/c/openocd/+/6665
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This board is (software wise) similar to the existing SAME54 Xplained
Pro board, with just a slightly different MCU. (Hardware wise, it
features a vastly different form factor.)
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Change-Id: I5e5435d49d333fb74471994ee84de59ed983153c
Reviewed-on: https://review.openocd.org/c/openocd/+/6747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Axel W.
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32mp13x has one core Cortex-A7.
The board Discovery Kit includes an on-board STLink-V3 with SWD
connection.
The webpage of the board is not active yet.
Change-Id: I8836b26612a160ead79766955ebefaf3d21a329c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6675
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
The driver jlink defines the command 'jlink serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: in former code the commands 'jlink serial' and 'jlink usb'
were mutually exclusive; running one of them would invalidate the
effect of a previous execution of the other. The new code gives
priority to 'adapter serial', even if executed before 'jlink usb'.
Change-Id: I920b0c136716f459b6fd6f7da8a01a7fa1ed389f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6656
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The driver xds110 defines the command 'xds110 serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: the original command 'xds110 serial' used a complex and
undocumented conversion of the serial number through multibyte
string, wide-character string and C cast. The XDS110 I can access
and the lsusb dumps available through Google don't show any
exotic USB serial that require such conversion. The original
developer doesn't remember any constraint that mandates such
conversion (see comments in https://review.openocd.org/4322/).
The conversion is removed by this patch.
Change-Id: I38909918079b2c1797ad85ebec2fea1b33743606
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6655
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver kitprog defines the command 'kitprog_serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I844cb815af01137392b6d12e1b5972fc77ac092d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6652
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver ftdi defines the command 'ftdi serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: Ia5b1f325b9fab8f58b5ea70f8b807e50b148b939
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6651
Tested-by: jenkins
The driver cmsis_dap defines the command 'cmsis_dap_serial' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I88e2d4de360a6c6f23529bb18494962a267250df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6649
Tested-by: jenkins
The driver aice defines the command 'aice serial' to specify the
serial string of the adapter, but actually does not use this value
in the code.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I892e0a4e1b41a7a87adf54a5736abf7419f32979
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6648
Tested-by: jenkins
GD32E23x from GigaDevice is cortex-M23 microcontroller and it can work with the stm32f1x driver.
Modifications are similar to this done for GD32F1x0 in #6164 (https://review.openocd.org/c/openocd/+/6164).
Configuration file is added because its cortex-M23 CPU ID is different.
I think that GigaDevice microcontrollers should be handled in an independent unit to separate them from STM32,
but nowadays quick solution is welcome.
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Change-Id: I91f31f5f66808bc50a8f607ac2c107e6b7c5e2b8
Reviewed-on: https://review.openocd.org/c/openocd/+/6527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Freeze the IWDG watchdog when cores are halted to prevent a reset
while debugging.
The PMIC present on some board senses the nsrst and forces a power
cycle to the target. The power cycle causes the SWJ-DP to restart
in JTAG mode. If the debugger is using SWD, the mismatch triggers
an error after the reset command.
Ignore the error detected by 'dap init' and proceed executing the
handler. The error in 'dap init' will force a reconnect during the
following 'dap apid', restoring the SWD functionality.
Change-Id: I04fcda6a5b8a1b080ab4e8890ecd0754d5ed12d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6599
Tested-by: jenkins
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
do not force the presence of the reset line, since some custom boards
may do not contain the reset line.
Change-Id: I031ab34012b34a1b49def9db16461f9de0ae29cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Fleck <fleckz@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/316/
Reviewed-on: https://review.openocd.org/c/openocd/+/6506
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
known boards are NUCLEO-G431KB, NUCLEO-G431RB and NUCLEO-G474RE
note: this work safely with B-G431B-ESC1, B-G474E-DPOW1,
STM32G474E-EVAL and STM32G484E-EVAL
Change-Id: I132a97e1816620b182983edc8a4b272b52b9241d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5484
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G031K8, NUCLEO-G070RB, NUCLEO-G071RB
note: this work safely with STM32G0316-DISCO, STM32G071B-DISCO
and STM32G081B-EVAL
Change-Id: I483b6f44409228cd8c2c97b3c560927d1645c517
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5483
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for ECP5 FPGA targets and board based on this chips:
Radiona ULX3S and Lambdaconcept ECPIX-5
Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6112
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The V3U SoC is unique in that it now has 8x CA76 and CR52,
while the previous SoCs had CA57/CA53/CR7 . This can still
be handled without too complex modifications to the gen3
configuration file, so add the logic to handle it there.
Change-Id: I7ab33eacc1fd379d369988d3d6690d2e82346c7e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On SMP Renesas R-Car Gen2/Gen3 systems, select the boot core as
the default target using the 'targets' command. This way, the
user can start debugging code running on the boot core without
having to switch to the boot core by explicitly invoking 'targets'
command first, since it is likely the debugged code will run on
the boot core. Note that most of the code is already in place, it
was just not used, so this is more of a fix to make the original
intention work.
Change-Id: I727808adce617c1d9ebd6ffa34f60f5882cdae60
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6313
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This file has been added to OpenOCD 0.5.0 in 2011, before gerrit
gets in use, with commit ba71e8c521 ("at91: add chip register
definition and generic init support").
The only procedure in the file has never been referenced in any
other part of OpenOCD. This procedure has syntax errors while uses
its argument 'cs' and several unmatched parenthesis, which clearly
highlights that it has never been used so far.
Gerrit does not report any patch aimed at fixing it.
Even if the file seems unused and could be removed, let's fix it
in the hope it could get used.
While there, remove some useless parenthesis and format it using
the new simplified syntax required by jimtcl 0.81.
Change-Id: Ied26456262e7b99de37667a8ce418f4f12e237bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ba71e8c521 ("at91: add chip register definition and generic init support")
Reviewed-on: http://openocd.zylin.com/6157
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Both http://openocd.zylin.com/542/ and http://openocd.zylin.com/543/
introduce the same typo in the bitfield for initializing the l2
cache of imx53.
One year later, http://openocd.zylin.com/1461/ copy-pastes the same
typo.
The comment above the code show that it's really an error and not
the expected behaviour.
Fix the typo replacing the incorrect comparison '<' with a left
shift.
Change-Id: I43725731a2228e28a676215f76936fa289d9395e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e3b3273433 ("cfg: add imx53loco board config")
Fixes: 108a458ab8 ("cfg: add icnova_imx53_sodimm board config")
Fixes: e608ced330 ("ftdi/board: Add support for DENX M53EVK")
Reviewed-on: http://openocd.zylin.com/6156
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Chip is similar to imx8x series but has different cores at different
addresses.
Support for reduced versions is not yet available.
Tested on imx8qm-mek board
Change-Id: Ia34a80d561ab2849a570d8c375b936a45cbf45ca
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-on: http://openocd.zylin.com/5042
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The Broadcom BCM2711 used in Raspberry Pi 4
No documentation was found on Broadcom website
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711/
Change-Id: I3db6c9af520af8ab4c21ad35ff0f2db28efc0325
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6066
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Broadcom chip used in the Raspberry Pi 2 Model B
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2836
Change-Id: I50b040db213c5b72f63d5f5534c552426c7376f9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6068
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the Broadcom chip used in the Raspberry Pi Model A, B, B+,
the Compute Module, and the Raspberry Pi Zero.
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2835
Change-Id: Ifeb012952473d624327e8c010ac5c886d9473aa0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6067
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Create the TPIU and SWO device in target config file.
Replace the target event 'trace-config' with the TPIU/SWO event
'post-enable'.
Extend the existing code in the event handler to properly set the
gpio mode and speed to permit synchronous trace.
This patch is not exhaustive of all the targets that have SWO, but
has to be considered as an initial example.
Change-Id: If4bbf364c0d2aef3ae49951e76507a3b1cfd58e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5859
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Add board and target configuration files for
Ampere eMAG8180 board and Ampere eMAG processor.
Tested on an Ampere eMAG8180 development platform.
Change-Id: I222653f0fc12d25202a7e469db3594076cbc38ed
Signed-off-by: Anthony Ferranti <ferranti@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5569
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add basic connection details for AM654 and J721E SoCs from TI.
See AM65x Technical Reference Manual (SPRUID7, April 2018)
for further details: https://www.ti.com/lit/pdf/spruid7
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: https://www.ti.com/lit/pdf/spruil1
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Change-Id: Ie5108c6ad6f1304a6bf5b9f81aa9ebd33b8a559d
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: http://openocd.zylin.com/5182
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
TCL expands the variables only if preceded by a dollar sign.
Add the missing dollar before the variable's name '_CPUTAPID'.
Change-Id: Icc5d0dddf24f75d12ee63fee69e1b265e842ca43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Wes Cilldhaire <wes@sol1.com.au>
Fixes: c3166b43e4 ("tcl/target: Add QuickLogic EOS S3 MCU configuration")
Reviewed-on: http://openocd.zylin.com/6079
Tested-by: jenkins
Reviewed-by: TM <tommy_murphy@hotmail.com>
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.
Strip the execution permission.
Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
only core0 is brought up by bootloader
Change-Id: I1d6b5e6ba7498beadbf3805f4271f0197e411bd5
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/5980
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use the board file name as <company>_<name>.cfg
Add the SPDX tag to workaround an error in checkpatch that fails
to recognize as valid a patch that only changes a file name.
Change-Id: I929cd9e5f9fe2e7386950643487534c9a5a05bc6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5931
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
regsub doesn't work correctly on macOS Catalina, which results in
an incorrect CHIPNAME derived from the current target. Since regsub
is only used by this target, replace it with a simple string search
for '.' followed by a substring. This is funcionally equivalent to
what the regular expression was doing, but instead relies in simpler
string operations that should have little to no differences
between systems.
Also, refactor CHIPNAME detection into proc stm32h7x_chipname, so
it's always retrieved in the same way without duplicating the code.
Change-Id: Ia9f63f56b508688e74278b022eaec47e503916e7
Signed-off-by: Alberto Garcia Hierro <alberto@garciahierro.com>
Reviewed-on: http://openocd.zylin.com/5872
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
in RM0399 rev2, there was these bits in DBGMCU_CR registers:
- DBGSTBY_D3 : bit 7
- DBGSTOP_D3 : bit 8
these bits have been changed to reserved in rev3
Change-Id: I9d10d90e383795dc8e25a117d59fa065dc594610
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5861
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In commit a1ce28b118 ("rename some target scripts to be
consistent with the rest") the following renames was applied, but
the old names are still referenced:
tcl/target/{sam7se512.cfg => at91sam7se512.cfg}
tcl/target/{sam7x256.cfg => at91sam7x256.cfg}
Fix the board files to use to correct target config filename.
Change-Id: I7698aa0da7db95c2bd9ba7ab8c260905a975c857
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
When OpenOCD is installed to the host the 'tcl' folder gets
usually installed in /usr/share/openocd/, thus having 'tcl' as
prefix of the target's file causes 'find' to fail.
Remove the 'tcl' folder prefix.
Change-Id: I3dc484c8de6af8f5aae4dd1b230522ee47ae2ba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5887
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This is a) broken and b) doesn't include anything other than the
(broken) target alias. Don't see any reason for it to exist.
Change-Id: I833635eeac392bf7c0c39f51ff2f76525ba2d406
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/5884
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added comment to ti-icdi.cfg specifying how to get serial and an example of
specifying hla_serial for ti-icdi devices. This has been implemented in revision
2121a8f92969804611412b705af8114697a647dc
Change-Id: I648458a4dea176beae6a3f1a4e5641d0206077eb
Signed-off-by: John Pham <jhnphm@gmail.com>
Reviewed-on: http://openocd.zylin.com/2528
Tested-by: jenkins
Reviewed-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
nrf52_recover was merged in pre "Handle Tcl return values consistently"
state - remove ocd_ prefixes.
Erase and unlock sequence was changed to comply Nordic semiconductor
recommendation:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_027%2FWP%2Fnwp_027%2FnWP_027_erasing.html
Change-Id: Ic54236c27cf25ad8091e9e572ba1ef846f0d47c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Pieter De Gendt <pieter.degendt@gmail.com>
Reviewed-on: http://openocd.zylin.com/5845
Tested-by: jenkins
Reviewed-by: Pieter De Gendt <pieter.degendt@gmail.com>
This driver provides support for Cadence JTAG BFM
The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.
Tested on Ampere emulation with Altra and Altra Max models
Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
All the HLA transports (hla_swd and hla_jtag) register the same
set of commands. Such commands are mainly aimed at handling JTAG
compatibility that is required for the transport hla_jtag only.
Split per transport the command registration and limit the
commands to only those required by the transport itself.
Replace the command "hla newtap" with the transport specific
"swd newdap" or "jtag newtap".
Deprecate the command "hla".
Change-Id: I79c78fa97b707482608516d3824151a4d07644c0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4877
Tested-by: jenkins
A JTAG TAP for boundary scan should be added in the scan chain
through the command "jtag newtap".
In some TCL target script the boundary scan TAP is added through
the command "swj_newdap", command that is inappropriate in this
context because specific for arm adi-v5 SWJ-DP.
This situation was probably created to bypass the error with HLA
framework, caused by missing command "jtag newtap".
Add the command "jtag newtap" in HLA, by reusing the existing
code for command "hla newtap".
Fix the TCL target scripts to use the command "jtag newtap" for
the boundary scan TAPs.
The TCL script target/psoc6.cfg has no evident reference to HLA,
so the reason for using "swj_newdap" is less clear. Nevertheless
it uses the wrong command and, once HLA is fixed, there is no
reason to avoid fixing it too.
Change-Id: Ia92f8221430cf6f3d2c34294e22e5e18963bb88c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4873
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
st_nucleo_l1.cfg is based on STM32L152RET6 which support
dualbank flash.
Change-Id: I7ecdb7b7557229465e23eed667f20cd84197dfc7
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Reviewed-on: http://openocd.zylin.com/5829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The "Corvette-F1" is an Arduino-compatible evaluation platform,
which fully supports AndesCore. The board has FTDI FT2232 to
connected to FPGA's JTAG interface.
The "ADP-XC7KFF676" is a development and prototyping board that
provides capacity for evaluation of AndesCore processors.
It works with AICE in-circuit debugging tools.
This patch also include target/nds32v5.cfg to support AndesCore
N22/N25F and AndeShape Platform AE250.
Change-Id: I144d5063d5086d00ec44634a5028b5ea5d2eba33
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/5338
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As the comment states, the 'init' command is issued before the
command 'dap apsel', otherwise it fails.
This dependency has been already fixed in commit e48690cb26
("target/arm_adi_v5: allow commands apsel and apcsw during init
phase"), so the command 'dap apsel' can now be issued directly.
Remove both the unneeded 'init' command and the comment that
documents and justify its presence.
Change-Id: I50f0a820fa7ead6f5a3bd9cc5180d521070822c9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5786
Tested-by: jenkins
Implementation largely taken from Nuvoton github
https://github.com/OpenNuvoton/OpenOCD-Nuvoton
Reset is still not fully compatible with OpenOCD framework.
Adapted to hidapi.
Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Reviewed-on: http://openocd.zylin.com/5720
Tested-by: jenkins
Reviewed-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Add support for Nu-Link1 over usb hidapi and config file.
The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.
Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.
Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Bitbang interface allows having a LED on one of the GPIO.
Let also linuxgpiod driver to specify and use the LED connection.
Change-Id: Id3d8772ee1808b92354fd073ba3947bacd8253ef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5770
Tested-by: jenkins
There is no flash bank support at the moment.
Change-Id: I52a2bde39425d94d9333cda002e5df0a1ef63c08
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5755
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this commit we add tcl configure files
for ARCv2 HS Development kit(HSDK). HSDK board
has Quad-core ARC HS38 CPU with L1 and L2
caches.
Change-Id: I372ef45428c7c7ca1421a6da3e5ed08b86f705e0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5784
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Actionpoint mechanism allows to setup HW breakpoints and watchpoints on Synopsys ARC CPUs.
This mechanism is controlled by DEBUG register and by a set of auxilary registers.
Each actionpoint is controlled by 3 aux registers: Actionpoint(AP) match mask(AP_AMM),
AP match value(AP_AMV) and AP control(AC).
Note: some fields of actionpoint_t structure will be used in further
support of watchpoints.
Change-Id: I4efb24675f247cc19d9122501c9e63c3126fcab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The USB adapter DLN-2 provides 32 GPIO (beside I2C, SPI, ...).
Use the first 6 GPIO for a SWD/JTAG bitbanging example through
linuxgpiod driver.
Change-Id: I229c2078142ec648fc6430b5d123539045dcfbda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5561
Tested-by: jenkins
In addition to the debug TAPs, the ICEPick C also supports
a bank of Test TAPs (limited functionality intended for
non-debuggable targets). Added support for Test TAPs to
the icepick_c_tapenable routine. Port numbers of 0 to 15
will continue to be handled as a debug TAP number. Test
TAPs will be port numbers of 16 to 31.
This functionality will be needed for doing a flash
mass erase on CC26xx/CC13xx targets. It is possible
for user application to block even adding the Cortex M
TAP to the scan chain, so the only way to unbrick the
target and erase the flash is using a component on a
test TAP of the device's ICEPick router.
Change-Id: I0aa52a08d43a00cbd396efdeadd504fc31c98510
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5715
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: If7465a752f47f3292e430c8b311148badfd384cd
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5478
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I13871ec13709055843e23b1b6da90694fd60505e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5477
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I30fcb8f291d401acaa1fe665db0eeabc250d24b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5476
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously the adapter speed settings were hard-coded to
connect with low speed then switch over to high speed
regardless what was mentioned in the cfg files. Now the
stm8 target intercept adapter speed settings and configure
the stm8 control registers accordingly.
Change-Id: I7419514e5214e4b43b9d51253cf5b7f04a233533
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The transport SWIM is selected twice, in board and in target, thus
a warning is generated at run-time. It should be fixed by remove a
line in the target file, but does not harm so let's keep it there
for the time being.
Change-Id: I479004dc16005a330d552c8dbd5def61690f9b9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5543
Tested-by: jenkins
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TRAILING_WHITESPACE --fix-inplace -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Ie7e3a236f4db9c70019e3b3c7e851edbd3a9dd84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5616
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I7b523f0ab5ec047ff167742a44c29984ac672cf4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5615
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The state machine of cortex-m have to pass through a set of state
before it get in "halted".
Add one more "arp_poll" to achieve the proper state during a
"reset halt" command in engineering boot.
Change-Id: I90828bf20ef75bd4018f8b911f727ae69c4d6e8f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5649
Tested-by: jenkins
Reviewed-by: Richard Braun <rbraun@sceen.net>
Empty lines at end of text files are useless.
Remove them.
Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5171
Tested-by: jenkins
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.
Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Drop bogus reference to board/renesas_gen2_common.cfg , which is a
non-existing file.
Fixes: a01474bb4c ("tcl/target: Switch Renesas R-Car Gen2 boards to new config")
Change-Id: Icb22d8456b7ac94d3a9a4ed354b246ee1332b122
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5564
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The stm32mp15x has one or two Cortex-A7 (depending on the P/N) and
one Cortex-M4.
The second core is automatically detected by the target script.
In "engineering boot" all the cores are accessible.
In "production boot" the Cortex-M4 is kept in reset state after
power-on or NRST.
The board DK2 includes a ST-Link/V2, but only SWD is connected.
Change-Id: Ib6ebefcc696b1716e0f98694cadf0b04fd7d11d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5454
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
With this commit we add tcl files which describes
ARCv2 architecture features and configure files
for ARCv2 EMSK board.
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
Changes:
22.01.2020:
-Removed "actionpoints" handling code in
tcl/cpu/arc/v2.tcl because this capability
is not supported yet.
Changes:
17.03.2020:
-Update Licence headers
-Cleanup indents
-Removed "reset halt" in boards .tcl
-Updated adapter frequency commands
Changes:
15.03.2020:
-Removed "init" in the of boards .tcl
Change-Id: I51bf620abe7b8e046e1dccc861a7d963965d3a42
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5350
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
nSRST and sysreqreset are both broken for these targets. Upon a
hard reset, the target disables the TDO/TDI pins and the
ICEPick router will remove the target's TAP from the scan
chain. The scripts to do these tasks are run, but then
OpenOCD throws the reset again breaking the debug connection.
Until that issue can be resolved, vectreset is the only
reset that works without breaking the debug connection.
Update: original patch didn't have the correct reset command.
Change-Id: If7c985b703c87399a13364609d370d6222f4a66c
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5511
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
On CC32xx family of devices, sysrequest is disabled, and
vectreset is blocked by the boot loader (stops in a while(1)
statement). srst reset can leave the target in a state
that prevents debug.
This change enables using vectreset on SF variants by
moving the PC to the start of the user application in
internal flash. This allows for a more reliable reset,
but with two caveats:
1) This only works for the SF variant with internal
flash.
2) This only resets the CPU and not any peripherals.
Tested on CC3220SF rev B Launchpad in both SWD and
JTAG modes. Confirmed proper behavior of reset,
reset init, reset halt, and reset run commands.
Update: reworked per comment in code review. Re-tested
with CC3220SF Launchpad as both CC3220SF and as
CC32xx board to confirm reset behavior as expected.
Update: Added adapter srst delay 1100 line to the
CC3200 LaunchXL configuration file.
Change-Id: Ibc042d785c846c2223ae55b8f2410b75ed2df354
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5489
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Confirmed that sysresetreq is supported and works better
for MSP432P4 and MSP432E4 targets than srst that was
previously being used.
Tested on MSP432P4111, MSP432P401R, and MSP432E401Y
Launchpads.
Change-Id: I1454c3379b9300bc133f82a766daeaefb98dbaac
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5488
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Starting with XDS110 firmware version 3.0.0.0, the peak TCK
frequency became 14,000 kHz. So the delay count calculation
in the current driver has been updated to use the new
formula for setting the TCK speed depending on which version
of the firmware is detected. And because of the changes, the
default TCK settings for the XDS110 based Launchpads can be
adjusted to take advantage of the higher TCK performance.
Note that the values used have been determined through
testing in the automated test labs to be the highest TCK
frequency with the XDS110 that are still reliable.
Different boards have a different peak TCK setting that
should be safe.
Change-Id: I4d66e90d8fac8272641ba4db4a3a510e3b444d86
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5493
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32WLEx devices are based on arm Cortex-M4 running at 48MHz,
contains a single bank of maximum 256 Kbytes of flash memory.
there is 3 variants with different Flash/RAM sizes:
STM32WLE5JC : 256K/64K
STM32WLE5JB : 128K/48K
STM32WLE5J8 : 64K/20K
the work-area size is set to 20 kb to fit in STM32WLE5J8
Change-Id: Ie8e186fe4be97cbc25c53ef0ade4b4dbbcee6f66
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5450
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash module of STM32G0/G4 family is quite similar to the one of
STM32L4, so only minor changes are required, in particular
adaption of flash loader to Cortex-M0. Register addresses
passed to flash loader to simplify integration of L5.
Added re-probe after option byte load.
Added flash size override via cfg file.
WRPxxR mask now based on max. number of pages instead of fixed 0xFF,
as G4 devices fill up unused bits with '1'.
Sizes in stm32l4_probe changed to multiples of 1kB.
Tested with Nucleo-G071RB, G030J6, Nucleo-G431RB and Nucleo-G474RE.
Gap handling in G4 Cat. 3 dual bank mode tested with STM32G473RB.
This handling isn't optimal as the bank size includes the
size of the gap. WB not tested.
Change-Id: I24df7c065afeb71c11c7e96de4aa9fdb91845593
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4807
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The RZ/A1 is not part of the R-Car family, but is rather an RZ family.
Fix the naming.
Change-Id: I5f882b2467e87e534e0f1c827554e664a7d55664
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5445
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change-Id: I693e5b7933fc61956010a96be57ee6eb8abd3c31
Signed-off-by: Anton V. Kirilchik <kosmonaffft@gmail.com>
Reviewed-on: http://openocd.zylin.com/5422
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Both Gen2 and Gen3 used the same init_reset{} implementation,
pull it into common file and include it from both generations.
Moreover, this behavior is SoC specific, not board specific,
so move the common init_reset into target/ directory.
Change-Id: I5489a4bff9a786da8cb7fd7a515b0c9ce9dc16e3
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5400
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Adopted only fast algorithm for flash programming:
- write_word and write_byte methods have been removed.
- start and end write alignments have been defined.
Moved flash controller registers offsets in a common file
shared with the flash algorithm.
- the flash base address is passed to the flash algorithm
as a parameter.
Removed unused functions
Change-Id: I80aeab3994e477044bbcf02e66d9525dae0cb491
Signed-off-by: luca vinci <luca.vinci@st.com>
Reviewed-on: http://openocd.zylin.com/5393
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Michele Sardo <msmttchr@gmail.com>
Drop old Renesas Gen2 SoC configurations, as they were superseded by
the new unified config.
Change-Id: I7c2ccbdc13b01a552ce9cafdc1538f226beaa9f2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5399
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Switch Renesas R-Car Gen2 boards which are currently supported from
the old ad-hoc SoC configuration to the new unified configuration.
Change-Id: I8a67bceb3ae92d840ae4dbac20868c75e83f7d58
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5398
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add configuration for the Renesas R-Car Generation 2 targets.
These are SoCs with Cortex A15s and A7s. All cores currently
supported by OpenOCD are supported here as well as two new
cores, M2N and V2H, for the sake of support completeness.
Change-Id: Ib6fe70a91360b4f8bd69822ee28b6dea530cfa0a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5397
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Some text file is missing newline at EOF.
Add it.
Change-Id: Ieebc790096f40961283c644642e56fde975e957f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5167
Tested-by: jenkins
Board includes an internal adapter (interface/ftdi/imx8mp-evk.cfg) and a
standard external ARM-10 connector.
Change-Id: Ibb301011665b1edfb95be1213d8100143f6839dd
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The imx8mp-evk board has a FT4232H chip connected to the chip's JTAG
pins.
Switching between this on-board interface and the external ARM-10
connector is controlled by an GPIO which is behind an i2c expander
connected to the same FTDI chip.
Switching can be performed using the NXP bcu tool:
https://github.com/NXPmicro/bcu
Change-Id: Ic910515f76eaf09ea6d0f755b026fb09cf09ccfc
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5426
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When $ADDRESS == $BASE that address used to be excluded.
After this commit $ADDRESS == $BASE is within the range.
Now the rule for "iswithin" is:
$BASE <= $ADDRESS < ($BASE + $LEN)
Thanks to Antonio Borneo <borneo.antonio@gmail.com> for noticing this.
Change-Id: I74373c6010e069372d886fa7ecd8120892616834
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4799
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change-Id: Ib452435b13c3cb8d14453d983151936238b9601d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5419
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Currently only used internally at Unjo.
Change-Id: I7786e95e1bd755a73156ecad5b6d7f6273d8ddef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5251
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Avoid annoying "deprecated" messages in the scripts
distributed with OpenOCD code.
Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5287
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently the code assumes the adapter uses raw SWD, and the expected ID
code of the CPU is even wrong. An adapter speed is also not specified.
All these prevents the config file to be used with ST-Link.
Fix the config file, to allow it to be used with ST-Link.
Change-Id: I1244320fabfe8ee23da5a56a592dbeddc72cc8d5
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-on: http://openocd.zylin.com/5297
Tested-by: jenkins
Reviewed-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
micbis
Thomas Hebb
Steve Marple
Salvatore Giorgio PECORINO
Tomas Vanek
Markus Reiter
Marc Schink
Tarek BOCHKATI
Sean Anderson
Antonio Borneo
Nishanth Menon
Jacek Wuwer
Hans-Erik Floryd
Doug Brunner
Joerg Wunsch
asier70
Andreas Sandberg
Wealian Liao
Oleksij Rempel
Ranjith Chandran
Jian-Hong Pan
Matthew Mets
Patrick Stewart
Andreas Fritiofson
Florian Fainelli
Marek Vasut
Rohit Singh
Olivier DANET
Peter Lawrence
Leonard Crestez
Andrew Wesie
Felipe Balbi
Jiri Kastner
Anthony Ferranti
Tarek BOCHKATI
Andreas Bolsch
Alberto García Hierro
Jonathan McDowell
Karl Palsson
Diego Herranz
John Pham
Kevin Burke
Ulrich-Lorenz Schlüter
Jan Kowalewski
Alexandre Bourdiol
Hellosun Wu
Zale Yu
Evgeniy Didin
Edward Fewell
Alistair Francis
Ake Rehnman
Liming Sun
Anton V. Kirilchik
luca vinci
Piotr Kasprzyk
Icenowy Zheng