Use the board file name as <company>_<name>.cfg
Add the SPDX tag to workaround an error in checkpatch that fails
to recognize as valid a patch that only changes a file name.
Change-Id: I929cd9e5f9fe2e7386950643487534c9a5a05bc6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5931
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
regsub doesn't work correctly on macOS Catalina, which results in
an incorrect CHIPNAME derived from the current target. Since regsub
is only used by this target, replace it with a simple string search
for '.' followed by a substring. This is funcionally equivalent to
what the regular expression was doing, but instead relies in simpler
string operations that should have little to no differences
between systems.
Also, refactor CHIPNAME detection into proc stm32h7x_chipname, so
it's always retrieved in the same way without duplicating the code.
Change-Id: Ia9f63f56b508688e74278b022eaec47e503916e7
Signed-off-by: Alberto Garcia Hierro <alberto@garciahierro.com>
Reviewed-on: http://openocd.zylin.com/5872
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
in RM0399 rev2, there was these bits in DBGMCU_CR registers:
- DBGSTBY_D3 : bit 7
- DBGSTOP_D3 : bit 8
these bits have been changed to reserved in rev3
Change-Id: I9d10d90e383795dc8e25a117d59fa065dc594610
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5861
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In commit a1ce28b118 ("rename some target scripts to be
consistent with the rest") the following renames was applied, but
the old names are still referenced:
tcl/target/{sam7se512.cfg => at91sam7se512.cfg}
tcl/target/{sam7x256.cfg => at91sam7x256.cfg}
Fix the board files to use to correct target config filename.
Change-Id: I7698aa0da7db95c2bd9ba7ab8c260905a975c857
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
When OpenOCD is installed to the host the 'tcl' folder gets
usually installed in /usr/share/openocd/, thus having 'tcl' as
prefix of the target's file causes 'find' to fail.
Remove the 'tcl' folder prefix.
Change-Id: I3dc484c8de6af8f5aae4dd1b230522ee47ae2ba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5887
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This is a) broken and b) doesn't include anything other than the
(broken) target alias. Don't see any reason for it to exist.
Change-Id: I833635eeac392bf7c0c39f51ff2f76525ba2d406
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/5884
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added comment to ti-icdi.cfg specifying how to get serial and an example of
specifying hla_serial for ti-icdi devices. This has been implemented in revision
2121a8f92969804611412b705af8114697a647dc
Change-Id: I648458a4dea176beae6a3f1a4e5641d0206077eb
Signed-off-by: John Pham <jhnphm@gmail.com>
Reviewed-on: http://openocd.zylin.com/2528
Tested-by: jenkins
Reviewed-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
nrf52_recover was merged in pre "Handle Tcl return values consistently"
state - remove ocd_ prefixes.
Erase and unlock sequence was changed to comply Nordic semiconductor
recommendation:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_027%2FWP%2Fnwp_027%2FnWP_027_erasing.html
Change-Id: Ic54236c27cf25ad8091e9e572ba1ef846f0d47c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Pieter De Gendt <pieter.degendt@gmail.com>
Reviewed-on: http://openocd.zylin.com/5845
Tested-by: jenkins
Reviewed-by: Pieter De Gendt <pieter.degendt@gmail.com>
This driver provides support for Cadence JTAG BFM
The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.
Tested on Ampere emulation with Altra and Altra Max models
Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
All the HLA transports (hla_swd and hla_jtag) register the same
set of commands. Such commands are mainly aimed at handling JTAG
compatibility that is required for the transport hla_jtag only.
Split per transport the command registration and limit the
commands to only those required by the transport itself.
Replace the command "hla newtap" with the transport specific
"swd newdap" or "jtag newtap".
Deprecate the command "hla".
Change-Id: I79c78fa97b707482608516d3824151a4d07644c0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4877
Tested-by: jenkins
A JTAG TAP for boundary scan should be added in the scan chain
through the command "jtag newtap".
In some TCL target script the boundary scan TAP is added through
the command "swj_newdap", command that is inappropriate in this
context because specific for arm adi-v5 SWJ-DP.
This situation was probably created to bypass the error with HLA
framework, caused by missing command "jtag newtap".
Add the command "jtag newtap" in HLA, by reusing the existing
code for command "hla newtap".
Fix the TCL target scripts to use the command "jtag newtap" for
the boundary scan TAPs.
The TCL script target/psoc6.cfg has no evident reference to HLA,
so the reason for using "swj_newdap" is less clear. Nevertheless
it uses the wrong command and, once HLA is fixed, there is no
reason to avoid fixing it too.
Change-Id: Ia92f8221430cf6f3d2c34294e22e5e18963bb88c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4873
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
st_nucleo_l1.cfg is based on STM32L152RET6 which support
dualbank flash.
Change-Id: I7ecdb7b7557229465e23eed667f20cd84197dfc7
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Reviewed-on: http://openocd.zylin.com/5829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The "Corvette-F1" is an Arduino-compatible evaluation platform,
which fully supports AndesCore. The board has FTDI FT2232 to
connected to FPGA's JTAG interface.
The "ADP-XC7KFF676" is a development and prototyping board that
provides capacity for evaluation of AndesCore processors.
It works with AICE in-circuit debugging tools.
This patch also include target/nds32v5.cfg to support AndesCore
N22/N25F and AndeShape Platform AE250.
Change-Id: I144d5063d5086d00ec44634a5028b5ea5d2eba33
Signed-off-by: Hellosun Wu <wujiheng.tw@gmail.com>
Reviewed-on: http://openocd.zylin.com/5338
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As the comment states, the 'init' command is issued before the
command 'dap apsel', otherwise it fails.
This dependency has been already fixed in commit e48690cb26
("target/arm_adi_v5: allow commands apsel and apcsw during init
phase"), so the command 'dap apsel' can now be issued directly.
Remove both the unneeded 'init' command and the comment that
documents and justify its presence.
Change-Id: I50f0a820fa7ead6f5a3bd9cc5180d521070822c9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5786
Tested-by: jenkins
Implementation largely taken from Nuvoton github
https://github.com/OpenNuvoton/OpenOCD-Nuvoton
Reset is still not fully compatible with OpenOCD framework.
Adapted to hidapi.
Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Reviewed-on: http://openocd.zylin.com/5720
Tested-by: jenkins
Reviewed-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Add support for Nu-Link1 over usb hidapi and config file.
The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.
Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.
Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Bitbang interface allows having a LED on one of the GPIO.
Let also linuxgpiod driver to specify and use the LED connection.
Change-Id: Id3d8772ee1808b92354fd073ba3947bacd8253ef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5770
Tested-by: jenkins
There is no flash bank support at the moment.
Change-Id: I52a2bde39425d94d9333cda002e5df0a1ef63c08
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5755
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this commit we add tcl configure files
for ARCv2 HS Development kit(HSDK). HSDK board
has Quad-core ARC HS38 CPU with L1 and L2
caches.
Change-Id: I372ef45428c7c7ca1421a6da3e5ed08b86f705e0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5784
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Actionpoint mechanism allows to setup HW breakpoints and watchpoints on Synopsys ARC CPUs.
This mechanism is controlled by DEBUG register and by a set of auxilary registers.
Each actionpoint is controlled by 3 aux registers: Actionpoint(AP) match mask(AP_AMM),
AP match value(AP_AMV) and AP control(AC).
Note: some fields of actionpoint_t structure will be used in further
support of watchpoints.
Change-Id: I4efb24675f247cc19d9122501c9e63c3126fcab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The USB adapter DLN-2 provides 32 GPIO (beside I2C, SPI, ...).
Use the first 6 GPIO for a SWD/JTAG bitbanging example through
linuxgpiod driver.
Change-Id: I229c2078142ec648fc6430b5d123539045dcfbda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5561
Tested-by: jenkins
In addition to the debug TAPs, the ICEPick C also supports
a bank of Test TAPs (limited functionality intended for
non-debuggable targets). Added support for Test TAPs to
the icepick_c_tapenable routine. Port numbers of 0 to 15
will continue to be handled as a debug TAP number. Test
TAPs will be port numbers of 16 to 31.
This functionality will be needed for doing a flash
mass erase on CC26xx/CC13xx targets. It is possible
for user application to block even adding the Cortex M
TAP to the scan chain, so the only way to unbrick the
target and erase the flash is using a component on a
test TAP of the device's ICEPick router.
Change-Id: I0aa52a08d43a00cbd396efdeadd504fc31c98510
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5715
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: If7465a752f47f3292e430c8b311148badfd384cd
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5478
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I13871ec13709055843e23b1b6da90694fd60505e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5477
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I30fcb8f291d401acaa1fe665db0eeabc250d24b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5476
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously the adapter speed settings were hard-coded to
connect with low speed then switch over to high speed
regardless what was mentioned in the cfg files. Now the
stm8 target intercept adapter speed settings and configure
the stm8 control registers accordingly.
Change-Id: I7419514e5214e4b43b9d51253cf5b7f04a233533
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The transport SWIM is selected twice, in board and in target, thus
a warning is generated at run-time. It should be fixed by remove a
line in the target file, but does not harm so let's keep it there
for the time being.
Change-Id: I479004dc16005a330d552c8dbd5def61690f9b9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5543
Tested-by: jenkins
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TRAILING_WHITESPACE --fix-inplace -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Ie7e3a236f4db9c70019e3b3c7e851edbd3a9dd84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5616
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I7b523f0ab5ec047ff167742a44c29984ac672cf4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5615
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The state machine of cortex-m have to pass through a set of state
before it get in "halted".
Add one more "arp_poll" to achieve the proper state during a
"reset halt" command in engineering boot.
Change-Id: I90828bf20ef75bd4018f8b911f727ae69c4d6e8f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5649
Tested-by: jenkins
Reviewed-by: Richard Braun <rbraun@sceen.net>
Empty lines at end of text files are useless.
Remove them.
Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5171
Tested-by: jenkins
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.
Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Drop bogus reference to board/renesas_gen2_common.cfg , which is a
non-existing file.
Fixes: a01474bb4c ("tcl/target: Switch Renesas R-Car Gen2 boards to new config")
Change-Id: Icb22d8456b7ac94d3a9a4ed354b246ee1332b122
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5564
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The stm32mp15x has one or two Cortex-A7 (depending on the P/N) and
one Cortex-M4.
The second core is automatically detected by the target script.
In "engineering boot" all the cores are accessible.
In "production boot" the Cortex-M4 is kept in reset state after
power-on or NRST.
The board DK2 includes a ST-Link/V2, but only SWD is connected.
Change-Id: Ib6ebefcc696b1716e0f98694cadf0b04fd7d11d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5454
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
With this commit we add tcl files which describes
ARCv2 architecture features and configure files
for ARCv2 EMSK board.
Changes since v1:
-Moved from http://openocd.zylin.com/#/c/5332/4
into separate commit.
Changes:
22.01.2020:
-Removed "actionpoints" handling code in
tcl/cpu/arc/v2.tcl because this capability
is not supported yet.
Changes:
17.03.2020:
-Update Licence headers
-Cleanup indents
-Removed "reset halt" in boards .tcl
-Updated adapter frequency commands
Changes:
15.03.2020:
-Removed "init" in the of boards .tcl
Change-Id: I51bf620abe7b8e046e1dccc861a7d963965d3a42
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5350
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
nSRST and sysreqreset are both broken for these targets. Upon a
hard reset, the target disables the TDO/TDI pins and the
ICEPick router will remove the target's TAP from the scan
chain. The scripts to do these tasks are run, but then
OpenOCD throws the reset again breaking the debug connection.
Until that issue can be resolved, vectreset is the only
reset that works without breaking the debug connection.
Update: original patch didn't have the correct reset command.
Change-Id: If7c985b703c87399a13364609d370d6222f4a66c
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5511
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
On CC32xx family of devices, sysrequest is disabled, and
vectreset is blocked by the boot loader (stops in a while(1)
statement). srst reset can leave the target in a state
that prevents debug.
This change enables using vectreset on SF variants by
moving the PC to the start of the user application in
internal flash. This allows for a more reliable reset,
but with two caveats:
1) This only works for the SF variant with internal
flash.
2) This only resets the CPU and not any peripherals.
Tested on CC3220SF rev B Launchpad in both SWD and
JTAG modes. Confirmed proper behavior of reset,
reset init, reset halt, and reset run commands.
Update: reworked per comment in code review. Re-tested
with CC3220SF Launchpad as both CC3220SF and as
CC32xx board to confirm reset behavior as expected.
Update: Added adapter srst delay 1100 line to the
CC3200 LaunchXL configuration file.
Change-Id: Ibc042d785c846c2223ae55b8f2410b75ed2df354
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5489
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Confirmed that sysresetreq is supported and works better
for MSP432P4 and MSP432E4 targets than srst that was
previously being used.
Tested on MSP432P4111, MSP432P401R, and MSP432E401Y
Launchpads.
Change-Id: I1454c3379b9300bc133f82a766daeaefb98dbaac
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5488
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Starting with XDS110 firmware version 3.0.0.0, the peak TCK
frequency became 14,000 kHz. So the delay count calculation
in the current driver has been updated to use the new
formula for setting the TCK speed depending on which version
of the firmware is detected. And because of the changes, the
default TCK settings for the XDS110 based Launchpads can be
adjusted to take advantage of the higher TCK performance.
Note that the values used have been determined through
testing in the automated test labs to be the highest TCK
frequency with the XDS110 that are still reliable.
Different boards have a different peak TCK setting that
should be safe.
Change-Id: I4d66e90d8fac8272641ba4db4a3a510e3b444d86
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5493
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32WLEx devices are based on arm Cortex-M4 running at 48MHz,
contains a single bank of maximum 256 Kbytes of flash memory.
there is 3 variants with different Flash/RAM sizes:
STM32WLE5JC : 256K/64K
STM32WLE5JB : 128K/48K
STM32WLE5J8 : 64K/20K
the work-area size is set to 20 kb to fit in STM32WLE5J8
Change-Id: Ie8e186fe4be97cbc25c53ef0ade4b4dbbcee6f66
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5450
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash module of STM32G0/G4 family is quite similar to the one of
STM32L4, so only minor changes are required, in particular
adaption of flash loader to Cortex-M0. Register addresses
passed to flash loader to simplify integration of L5.
Added re-probe after option byte load.
Added flash size override via cfg file.
WRPxxR mask now based on max. number of pages instead of fixed 0xFF,
as G4 devices fill up unused bits with '1'.
Sizes in stm32l4_probe changed to multiples of 1kB.
Tested with Nucleo-G071RB, G030J6, Nucleo-G431RB and Nucleo-G474RE.
Gap handling in G4 Cat. 3 dual bank mode tested with STM32G473RB.
This handling isn't optimal as the bank size includes the
size of the gap. WB not tested.
Change-Id: I24df7c065afeb71c11c7e96de4aa9fdb91845593
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4807
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The RZ/A1 is not part of the R-Car family, but is rather an RZ family.
Fix the naming.
Change-Id: I5f882b2467e87e534e0f1c827554e664a7d55664
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5445
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change-Id: I693e5b7933fc61956010a96be57ee6eb8abd3c31
Signed-off-by: Anton V. Kirilchik <kosmonaffft@gmail.com>
Reviewed-on: http://openocd.zylin.com/5422
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Both Gen2 and Gen3 used the same init_reset{} implementation,
pull it into common file and include it from both generations.
Moreover, this behavior is SoC specific, not board specific,
so move the common init_reset into target/ directory.
Change-Id: I5489a4bff9a786da8cb7fd7a515b0c9ce9dc16e3
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5400
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Adopted only fast algorithm for flash programming:
- write_word and write_byte methods have been removed.
- start and end write alignments have been defined.
Moved flash controller registers offsets in a common file
shared with the flash algorithm.
- the flash base address is passed to the flash algorithm
as a parameter.
Removed unused functions
Change-Id: I80aeab3994e477044bbcf02e66d9525dae0cb491
Signed-off-by: luca vinci <luca.vinci@st.com>
Reviewed-on: http://openocd.zylin.com/5393
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Michele Sardo <msmttchr@gmail.com>
Drop old Renesas Gen2 SoC configurations, as they were superseded by
the new unified config.
Change-Id: I7c2ccbdc13b01a552ce9cafdc1538f226beaa9f2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5399
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Switch Renesas R-Car Gen2 boards which are currently supported from
the old ad-hoc SoC configuration to the new unified configuration.
Change-Id: I8a67bceb3ae92d840ae4dbac20868c75e83f7d58
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5398
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add configuration for the Renesas R-Car Generation 2 targets.
These are SoCs with Cortex A15s and A7s. All cores currently
supported by OpenOCD are supported here as well as two new
cores, M2N and V2H, for the sake of support completeness.
Change-Id: Ib6fe70a91360b4f8bd69822ee28b6dea530cfa0a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5397
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Some text file is missing newline at EOF.
Add it.
Change-Id: Ieebc790096f40961283c644642e56fde975e957f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5167
Tested-by: jenkins
Board includes an internal adapter (interface/ftdi/imx8mp-evk.cfg) and a
standard external ARM-10 connector.
Change-Id: Ibb301011665b1edfb95be1213d8100143f6839dd
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The imx8mp-evk board has a FT4232H chip connected to the chip's JTAG
pins.
Switching between this on-board interface and the external ARM-10
connector is controlled by an GPIO which is behind an i2c expander
connected to the same FTDI chip.
Switching can be performed using the NXP bcu tool:
https://github.com/NXPmicro/bcu
Change-Id: Ic910515f76eaf09ea6d0f755b026fb09cf09ccfc
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5426
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When $ADDRESS == $BASE that address used to be excluded.
After this commit $ADDRESS == $BASE is within the range.
Now the rule for "iswithin" is:
$BASE <= $ADDRESS < ($BASE + $LEN)
Thanks to Antonio Borneo <borneo.antonio@gmail.com> for noticing this.
Change-Id: I74373c6010e069372d886fa7ecd8120892616834
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4799
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change-Id: Ib452435b13c3cb8d14453d983151936238b9601d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5419
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Currently only used internally at Unjo.
Change-Id: I7786e95e1bd755a73156ecad5b6d7f6273d8ddef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5251
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Avoid annoying "deprecated" messages in the scripts
distributed with OpenOCD code.
Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5287
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently the code assumes the adapter uses raw SWD, and the expected ID
code of the CPU is even wrong. An adapter speed is also not specified.
All these prevents the config file to be used with ST-Link.
Fix the config file, to allow it to be used with ST-Link.
Change-Id: I1244320fabfe8ee23da5a56a592dbeddc72cc8d5
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-on: http://openocd.zylin.com/5297
Tested-by: jenkins
Reviewed-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32H7x7 and STM32H7x5 devices contains two cores : CM7 + CM4
The second core creation is only done when
* DUAL_CORE variable is set to true
* non HLA interface is used
A second check for the second core existence is done in cpu1 examine-end
Once the second core is detected it gets examined.
Furthermore, the script provides a configurable CTI usage in order to halt
the cores simultaneously.
Tested on Rev X and V devices.
PS: the indentation was a mix of spaces and tabs, all changed to tabs.
Change-Id: Iad9c30826965ddb9be5dee628bc2e63f953bbcb8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The STM32H7 has three access ports. The DBGMCU component is available
through AP0 at 0x5C001000 and through AP2 at 0xE00E1000. Using the
latter is preferable for early configuration because it works in all
power states and while SRST is asserted, whereas the former does not.
Change-Id: Iaf8f01d769efb6655040060a8e1e951e1f7e50ab
Signed-off-by: Christopher Head <chead@zaber.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4742
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Correct check for end-of-region is:
$BASE + $LEN > $ADDRESS
And it is currently (wrongly) calculated as:
$ADDRESS > $BASE - $LEN
Change-Id: If10bfee19b0c7dbc085731ac1eda943f5d8a36a3
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4798
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is not flash bank support at the moment.
Change-Id: I833c009d9d21cdeb70b57d67eb557d50ed0fb4de
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5205
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also
adds configuration file for SSE-200 based Musca A board. Flash programming
support for Musca A QSPI flash is still not functional. This configuration
will be updated once that support lands into OpenOCD.
Please refer to ARM documentation for more information about SSE-200 and
Musca A.
Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/5006
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The V3M SoC is R8A77970 while the V3H SoC is R8A77980 . Update the
CHIPNAME and swap the SoCs to keep the list sorted.
Change-Id: I7e1777c0c7181e5e0beac98333f2047cb443d0df
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5140
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H target.
This is an SoC with one Cortex A9 ARMv7a core and
up to 10 MiB of on-SoC SRAM.
Change-Id: I20fd54b385fe1ba1cc325451c3fdfa3a835d4884
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H GR-Peach board,
which is a cheap development kit for the RZ/A1H SoC.
Change-Id: I7f5596ae47e6dff8e6d06cffd4dddca20f57d0ca
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5142
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The commands prefixed with "ocd_" are removed.
Remove them from configuration files.
Change-Id: Ib44627ee17a39f3d06b479507ab5a025073bf9a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5090
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* Add mem_ap for direct access to axi bus (without halting cpu)
* Mark m4 core with -defer-examine because it's not used by default
* Make a53.0 default target since it's the boot core
Change-Id: Id031533c5d4af346eb08a9ac2532fa1bca602913
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5036
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 the 6UL 6ULL 6ULZ chips are based on Cortex-A7
which is at a different address so a custom script is required.
Tested on imx6ull-14x14-evk
Change-Id: I72822d2241045c318389fadbc66d7aaabaaf4cb5
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5040
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 a Cortex-M4 was added with a second CoreSight
DAP so a separate script is required.
Tested on imx6sx-sdb running linux
Change-Id: I1561910b233015f42508f341175822c0827655ec
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5041
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike imx7d/solo supported by imx7.cfg the M4 core is on a different AP
and is always running by default so no -defer-examine is required.
There is also only one Cortex-A7
Tested on imx7ulp-evk
Change-Id: Ifa923d1b9a372c788e6654bc2233fd4d9073a32d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5043
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add a config to access the Amazon Kindle Model No. D00701 and D00801.
Both ebook readers are based on a Freescale i.MX31. A JTAG interface is
included in a 40 pin FFC connector marked "J9" on both variants.
Change-Id: I58bb1ded3d6706bc3798af488ca8bafb7dc45225
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3956
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Copy all SJC TAPIPs from imx6 reference manuals.
Some imx6 chips are based on Cortex-A7 or have an additional Cortex-M4
and need separate scripts.
Change-Id: I3b07d94058c2c5e6313cfc8bb43134a90682a62e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5034
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
OpenOCD scripts are usually indented with 4 spaces but here there are 8.
Change-Id: Iaad53e3b377d246d99119bb7bb5fd75d4422f564
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5039
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Looking through imx6 manuals all of them claim that "In follow-on
silicon revisions the ID value is subject to change by incrementing the
first nibble".
Handle this by passing -ignore-version to jtag newtap command.
Change-Id: I7fc4779f9757d527ea20a5174a8c90f919580013
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This allows bus access even when CPU is off.
Change-Id: I2d5c5581cd0169aecb92ac7b610810988a8dcef4
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5032
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch remaps the Flash over ITCM region as virtual to ensure that
any breakpoint placed in this area will be automatically set as an
hardware breakpoint. This patch is a fix to a regression introduced with
changes #4429.
Change-Id: I03d46d8537ef06b33a3d4a2328274667c6481969
Signed-off-by: Rocco Marco Guglielmi <roccomarco.guglielmi@gmail.com>
Reviewed-on: http://openocd.zylin.com/5097
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The imx8m also has a Cortex m4 so add a target for it.
Change-Id: I2abf62b6232c547fe9b12507f459835b11c63a6d
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-on: http://openocd.zylin.com/4501
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The OTP is part of the flash memory. It has 512 (1024 for F7) bytes
and is organized in 16 sectors with 32 (64 for F7) bytes each.
The OTP is exposed as separate flash bank 1 and can be used
with the usual flash commands.
Writing the OTP can be done as follows:
> stm32f2x otp 1 enable
> flash write bank 1 foo.bin 0
> mdw 0x1fff7800 4
> verify_image foo.bin 0x1fff7800
> stm32f2x otp 1 disable
Note: This patch is largely a rebase/cleanup of a patch
from 2012 by Laurent Charpentier and he did most of the work.
No new Clang-Analyzer warnings.
Change-Id: I5e6371f6a7c7a9929c1d7907d6ba4724f9d20d97
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The new Microchip (former Atmel) series powered by Cortex-M4 looks
very similar to older M0+ powered SAM D2x at the first sight.
Unfortunately the new series differs a lot in important details.
NVMCTRL has different register addresses, moved important bits
and even changed binary command set. An universal driver for all SAM D/E
would be very complicated. That's why a new driver was derived.
Tested on Microchip SAM E54 Xplained Pro kit (board cfg included).
Adjusted for the restructured dap support.
Checked by valgrind and clang static analyzer.
Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4272
Tested-by: jenkins
Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
The original script was broken by changes to the Cortex-A code. The
recent introduction of the mem_ap target provided a new mechanism to
allow the script to be fixed. This also adds an example board script
for the ADSP-SC584-EZBRD.
Change-Id: I36bc1ac6b6c036539f4175f1e65223ba10a35355
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4855
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The xilinx_ultrascale.cfg target is actually the configuration for a
ZynqMP, which is a combination of an UltraScale+ FPGA core and a quad
core A53. Update the filename/comments to reflect this, and include
the tap IDs for all known FPGA cores for this part.
Change-Id: I70dfcc99861a482b83b6a795e83021d9cf1fe047
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4850
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Agama family of devices (CC26x2/CC13x2) required an
additional bit to be set when adding the core's TAP into
the scan chain. The cancel reset bit 0x10000 tells the
ICEPick to take the bus out of reset so that the other
bits will take effect. This bit is a NOP on other devices
and ICEPicks, so the change shouldn't adversely affect
other devices.
Change-Id: I9245eef0936ea7eea28ae84ab5e8ce05fa63af40
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently it is impossible to flash ELF with correct offsets. The reason
is a bogus offset calculation extracted from base.
Since any other spi drivers do not care about base, do the same for
ath79 as well.
Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4821
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
original CC3200 launchpad works only with ti-icdi driver
which stopped to work after merging to master commit
d02de3a8a9
Change-Id: I247b5d99831fa744de1fdc5b8a7cffdf49fe953c
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/4792
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1
Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.
Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for reading halfword values from memory. This
command compliments existing support for writing halfwords (mwh).
Change-Id: I8ec628e65c05a7f00aa57e3af0f228eb8bd4d14e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4781
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since commit bae76053dc
gdb-attach event is defined as halt by default.
Remove useless and in case of bcm281xx wrong definitions of the event.
Change-Id: I8e69780a93722eb9392673303f54d502e71eceb6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4763
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
The reset_config line in the config file does not actually set
connect_assert_srst (the default is connect_deassert_srst), but it reads
as if it does. Clarify that the target is compatible with
connect_assert_srst, without suggesting that the file actually sets it
to that value.
Change-Id: I14e9445ab282d386b5d0055f6adf03d7c8878a8c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4743
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32h7x.cfg does not specify connect_assert_srst or
connect_deassert_srst in its reset_config. The comment claims that it
will therefore connect in reset. However, per the manual, the default
configuration is actually connect_deassert_srst, not
connect_assert_srst. In actual fact, connect_assert_srst does not work
on the STM32H7 because, while SRST is asserted, everything on the AXI
bus is inaccessible. The CPU core is accessible, but since the
examine-end event handler also pokes at the DBGMCU peripheral, that will
fail in connect_assert_srst mode. So using connect_deassert_srst is
appropriate, so fix the comment accordingly.
Change-Id: If3e32e871fb19cc61183bdf911b7c5efd80b62e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4741
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When using stlink for CM7 targets we have to rely on its firmware
to do the right thing as direct DAP access is not possible.
Change-Id: Ieee69f4eeea5c911f89f060f31ce86ed043bdfd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4732
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This allows for programming the PL part of the Xilinx Zynq 7000
Change-Id: I89e86c0f381951091f6948c46802d17d7f1f3500
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4177
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add/detect missing IDCODEs for the Spartan 7 family and Artix 25T
and Artix 12T.
Change-Id: Ib6c83c5592e90df1eb8e715e79b279da9a95f9c6
Signed-off-by: William D. Jones <wjones@wdj-consulting.com>
Reviewed-on: http://openocd.zylin.com/4428
Reviewed-by: Robert Jördens
Tested-by: jenkins
Reviewed-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Mimas A7 FPGA board has FTDI FT2232 whose channel B is connected to
Artix-7 FPGA's JTAG interface. Hence, OpenOCD can easily interface with
it via the its ftdi driver interface. Tested to be working great up to
30 MHz.
Change-Id: Ieda015fbc6135bf95ad5a069cbf38650da45911e
Signed-off-by: Rohit Singh <rohit91.2008@gmail.com>
Reviewed-on: http://openocd.zylin.com/4720
Tested-by: jenkins
Reviewed-by: Tim "mithro" Ansell <me@mith.ro>
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car Generation 3 targets.
These are SoCs with Cortex A57s, A53s, and R7s. All cores
are supported.
Change-Id: I795233210e4f647a1a2a0adea7c058ae98b5db70
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4669
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change-Id: Ic00d3192642c682f370a6f7f8b70ae29744eb746
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4678
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I7c5c9720ded329848647f17db95f845e46c01c19
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4674
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with Olimex ARM-USB-TINY-H adapter
Simple commands work fine but there are currently issues when attaching
remote gdb or running virt2phys:
https://sourceforge.net/p/openocd/tickets/201/
Change-Id: I86ccf1d93c5d23870bb522f92b3e2af190d529e8
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-on: http://openocd.zylin.com/4646
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds support for the C232HM-DDSL-0 and C232HM-EDSL-0
FT232H-based cables from FTDI. For more information, see:
http://www.ftdichip.com/Products/Cables/USBMPSSE.htm
Change-Id: Ic97423eb1e2f6b5ebae04943cd5cce86f38771d5
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4081
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Adding flash programming support for Maxim Integrated MAX32XXX
devices.
Change-Id: I5b0f57a885f9d813240e4bc2d9f765b743e1cfc3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/3543
Tested-by: jenkins
Reviewed-by: Ismail H. KOSE <ihkose@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
it is Atheros AR9331 based IoT dev board.
Change-Id: I6fc3cdea1bef49c53045018ff5acfec4d5610ba6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4424
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
More information about this board can be found here:
https://www.8devices.com/products/lima
Change-Id: Id35a35d3e986630d58d37b47828870afd107cc6a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4406
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable
Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4405
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This supports both 0.11 and 0.13 versions of the debug spec.
Support for `-rtos riscv` will come in a separate commit since it was
easy to separate out, and is likely to be more controversial.
Flash support for the SiFive boards will also come in a later commit.
Change-Id: I1d38fe669c2041b4e21a5c54a091594aac3e2190
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4578
Tested-by: jenkins
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id996c4de6dc9f25f71424017bf07689fea7bd3af
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4507
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
cortex m0+ on a tiny board, with an mEDBG (CMSIS-DAP) debug interface.
Change-Id: Iaedfab578b4eb4aa2d923bd80f220f59b34e6ef9
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/3402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ica0025ea465910dd664ab546b66f4f25b271f1f5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4570
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
As seen on the FRDM-LS1012A board.
Change-Id: Ifc9074b3f7535167b9ded5f544501ec2879f5db7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4594
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Factor out the code shared by all R-Car Gen2 boards into a single
file to get rid of the duplication.
Change-Id: I70b302c2e71f4e6fdccb2817dd65a5493bb393d8
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4533
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7794 E2
based Silk evaluation board.
Change-Id: I504b5630b1a2791ed6967c6c2af8851ceef9723f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
NOTE: This requires SW7[1] in position 1 (default is 0)
Reviewed-on: http://openocd.zylin.com/4532
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Erasing is not supported by the hardware, it can be written directly.
Tested on CY8CKIT-059, except modifying-write.
Change-Id: I6e920ed930dcd5c7f0b10c5b1b4791a828d9080a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3434
Tested-by: jenkins
Always probe for ECC mode and display ECC sectors if disabled.
Non-ECC write is implemented as zeroing the ECC/config bytes.
Erasing ECC sectors is ignored, erase-checking takes them into account.
Tested with CY8CKIT-059 (CY8C5888), except ECC mode.
Change-Id: If63b9ffca7ad8de038be3c086c49712b629ec554
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3432
Tested-by: jenkins
Added cc3220sf flash driver to support the TI CC3220SF
microcontrollers. Implemented flash driver to support the
internal flash of the CC3220SF. The implementation does not
support the serial flash of the CC32xx family that requires
connection over UART, and not via JTAG/SWD debug. Added config
files for both CC32xx devices (no flash) and CC3220SF (with
flash).
Updated to implement comments from code review.
Additional updates to handle remaining comments from review.
Additional updates per review.
Added code to only request aligned writes and full 32-bit
words down to flash helper algorithm. Updated for recent
changes in OpenOCD flash code.
Removed cc32xx.cfg file made obsolete by this patch.
Change-Id: I58fc1478d07238d39c7ef02339f1097a91668c47
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4319
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for the XDS110 debug probe using the APIs in the
probe's firmware. Includes support for older versions of the
firmware (with reduced performance) and support for a newer
version that includes OpenOCD specific APIs. Tested on various
TI LauchPads including MSP432P4, MSP432E4, CC2650, CC2652, and
CC3220SF.
Updated to add better support for swd switch. Removed issues found with
clang static analysis.
Updated to add rules entry for the XDS110 probe and Tiva DFU mode (which
affects both XDS110 and ICDI probes).
Change-Id: Ib274143111a68e67e80003797c6a68e3e80976b2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4322
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The "Blue Pill" is a popular development board with an STM32F103C8
micro controller. According to sources, it has a 128kB Flash on board
even though the option bytes only report 64kB. This patch therefore also
modifies target/stm32f1x.cfg to take an optional FLASH_SIZE variable into
account which the board file sets to 0x20000.
Change-Id: I8a78ccd2b5faf637c539ee3cf8136789ee15c95d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4495
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add configuration for the Renesas R-Car R8A7790 H2 target.
This is an SoC with four Cortex A15 and four Cortex A7
ARMv7a cores, only the four A15 cores are supported.
Change-Id: I6099b257cc0f04e6858ed5f5f8c8d8ad82ef7650
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4490
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Vybrid VF6xx SoCs contain an additional Cortex-M4
core connected to AP number 3 of the main DAP.
Change-Id: I59c020fdfc53e909b1f0dac1a8627a62cdaa74f2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3640
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
includes target configuration for i.MX8M SoC family,
board file needs to set up CHIPNAME and CHIPCORES
to match the actual hardware configuration
Change-Id: Ieb6d89cab2477a58f85d0ef9cd242710950191c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4434
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
configuration also contains a reset-init procedure that disables the
watchdog and initilizes the boards DDR memory so that you can upload
baremetal (e.g. boot loader) code into DDR and start it from there.
Change-Id: I4d2311b3708a5fcb5174a3447f34ae3904de7243
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7791 M2W target.
This is an SoC with two Cortex A15 ARMv7a cores, both cores
are supported.
This patch is based on initial submission by Adam Bass and
improvements by Niklas Söderlund.
Change-Id: I297da62b9ce71ad222a401d98e6bcb8502427673
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Adam Bass <adam.bass@renesas.com>
Cc: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-on: http://openocd.zylin.com/4485
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Most Xilinx FPGA devices contain an embedded, unique device identifier.
The identifier is nonvolatile, permanently programmed into the FPGA, and is
unchangeable providing a great serial / tracking number.
This commit adds generic support for reading the Xilinx Spartan 6 and 7
Series (Kintex, Artix, Ultrascale) Device DNA. The code is similar to
the function in fpga/xilinx-xc6s.cfg for Spartan 6 but the register
addresses are different and the logic has been simplified.
The code was not placed in xilinx-xc7.cfg. The approach of defining taps
in the same file as library code to use them is fundamentally broken on
boards that have more than one FPGA or other chips. This commit (like
the addition of support for Xilinx XADC) starts to remedy that by
splitting library code from board-specific fixed definitions.
The support code is sourced in the Kasli and KC705 board support files
as it was tested on these boards.
Change-Id: Iba559c7c1b7e93e1270535fd9e6650007f3794da
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4396
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The 7 Series FPGAs contain an on-chip 12 bit ADC that can probe die
temperature, internal power supply rail voltages as well as external
voltages. The XADC is available both from fabric as well as through the
JTAG TAP.
This code implements access throught the JTAG TAP.
https://www.xilinx.com/support/documentation/user_guides/ug480_7Series_XADC.pdf
Change-Id: I6cef4d0244add71749fa28b58a736302151cc4dd
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4395
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Kasli is an open hardware FPGA board. It is part of the Sinara family of
devices designed to control quantum physics experiments (see Sayma_AMC
for other boards already suppported by openocd).
Kasli was developed as part of the opticlock project. It features a
Xilinx Artix 7 100T FPGA, DDR3 RAM, a clock reconstruction and
distribution network, four 6 Gb/s transceiver links (three SFP and
one SATA) as well as interfaces to up to 12 Eurocard Extension Modules
(EEMs).
https://github.com/m-labs/sinara/wiki/Kaslihttp://www.opticlock.de/en/
Change-Id: I88b5e9f16b79e1e731056c45da6b5e1448d2c0e7
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4341
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Ultrascale series is a bit more complicated to handle since with the
stacked and interconnected dies the IR gets longer. This adds support
for all currently known chips from the Ultrascale family.
Change-Id: Ibac325dd6fadc76f73cc682b1c62c1a5f39f0786
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4188
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Make sure the user is aware he can lock the device though unlock is not
possible without access to MDM-AP.
Change-Id: I92676530e95d19489c6739748a99c2895849f90f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4403
Tested-by: jenkins
When a user asks for blaster I, he or she should either get it, or get
an error, not blaster II driver.
Change-Id: Ibc7683676ce42773e2b14ea5ccb3d119d1e6acea
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4381
Tested-by: jenkins
This is a second try for this patch. I removed the queues from the
previous version. I made it compatible with SRST reset and added
support for those features that could be supported in raw binary
mode.
Change-Id: I96fc06abbea9873e98b414f34afd9043fd9c2a41
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/3960
Tested-by: jenkins
Reviewed-by: Eric Work <work.eric@gmail.com>
Reviewed-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jacob Alexander <haata@kiibohd.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
30 MHz is not working reliably here
Change-Id: I38f5f8c7153fc64e313ee911b1629fb5f1114c39
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4242
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This makes it possible to program newer EFM32 and EFR32 chips with
JTAG, as opposed to SWD.
Change-Id: Ia3e8c1bbc66fc1f33e8cf2087ccf0d1b4dfd74e1
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4262
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The ICEPick-D jtag router has core control registers
that provide the same (or similar) functionality as
the tap control register, for individual cores
accessible through the same tap (e.g. through a DAP).
Core control registers are located at address "0x60 +
core-id" of the ROUTER address space (IR=ROUTER).
It is sometimes helpful or even necessary to modify the
core control register. This patch renames the
"icepick_d_coreid" function to the more appropriate
"icepick_d_core_control" and adds a "value" argument
that allows writing of arbitrary value.
"icepick_d_tapenable" is extended by an optional value
argument so that core control can be written as the tap
is enabled.
Change-Id: I0e7f91b596cb5075364c6c233348508f58e0a901
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Flash ROM API command PSOC4_CMD_SET_IMO48 is now optional on new devices.
Also code tidy up:
- improved system ROM call error detection
- probe does not require the target to be halted
- default_padded_value and erased_value set to 0
- fixed endianess problem in flash write and protection setting
- removed fancy chip detection table as it would be updated too often
- psoc4 flash_autoerase is now on by default to ease programming
psoc4.cfg distinguishes chip family and uses either proprietary acquire
function of a KitProg adapter or TEST_MODE workaround to "reset halt"
Change-Id: I2c75ec46ed0a95e09274fad70b62d6eed7b9ecdf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3807
Tested-by: jenkins
Reviewed-by: David Girault <david.f.girault@gmail.com>
Make all configs specify same JTAG and SWD GPIO numbers.
Change-Id: I65b09c1671c97f253f0aab88e511de7409d91e0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3932
Tested-by: jenkins
Some parts have only that much. Reported by robertfoos_ on IRC.
Change-Id: I684fdccfa62cf726466ddc467543a990fd88c4dc
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4369
Reviewed-by: Robert Foss <robert.foss@memcpy.io>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:
1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:
The previous logic was erroneous. The delay in clock cyles from a bit
written to the jtag interface to a bit read by the jtag interface is:
* The number of BYPASSed TAPs before this (jtagspi) tap
* The length of the jtagspi data register (1)
* The number of BYPASSed TAPs before this one.
I.e. it is just the number of enabled TAPs. This also gets rid of the
configuration parameter DR_LENGTH.
3. Use marker bit to start spi transfer
If there are TAPs ahead of this one on the JTAG chain, and we are in
DR-SHIFT, there will be old bits toggled through first before the first
valid bit destined for the flash.
This delays the begin of the JTAGSPI transaction until the first high bit.
4. New jtagspi protocol
A JTAGSPI transfer now consists of:
* an arbitrary number of 0 bits (from BYPASS registers in front of the
JTAG2SPI DR)
* a marker bit (1) indicating the start of the JTAG2SPI transaction
* 32 bits (big endian) describing the length of the SPI transaction
* a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
* an arbitrary number of cycles (to shift MISO/TDO data through
subsequent BYPASS registers)
5. xilinx_bscan_spi: clean up, add ultrascale
This is tested on the following configurations:
* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E
Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* Disables the data output pin while SWD is reading, so that a simple FTDI
SWD interface can be made by connecting TCK to SWD_CLK and TDI+TDO directly
to SWDIO. Enabled by setting SWDIO_OE to 0.
Change-Id: I7d3b71cf3f4eea163cb320aff69ed95d219190bd
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Reviewed-on: http://openocd.zylin.com/2274
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The Digilent SMT2 NC is nominally the connector-less version of the
SMT2. But neither the SMT2 configuration nor the HS3 configuration work
for on the Xilinx KCU105 board where the SMT2 NC is used.
Change-Id: Ieb27cbc6d8b0f9c64ef778e4e0c839acc85ec0ef
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4187
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
We can now use the generic stlink.cfg which allows for both ST-LINK/V2
and V2-1 debuggers.
Change-Id: I229c6fe5f6a6a4f2d3c787a49939846f102f9e24
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Reviewed-on: http://openocd.zylin.com/4313
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extend HLA interface to allow multiple VID/PID pairs and use it to
autodetect the connected stlink version.
Change-Id: I35cd895b2260e23cf0e8fcb1fc11a78c2b99c69b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3961
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New low-end chips have only 2k of RAM, workarea size adjusted
Change-Id: Ibfccd73fef9e6dabffc87d901736c5626ce411fe
Signed-off-by: Ilia Motornyi <elijah.mot@gmail.com>
Reviewed-on: http://openocd.zylin.com/4308
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Similar to the Sheevaplug fix inf95f8b70fbd0f7e9c91a2d9006b1abb2dd07ebf2
the OpenRD device has its JTAG interface on the first channel of the
ft2232, which is 0 for the new driver but was 1 for the old one. Correct
the config file appropriately. Also the device description was missing
the trailing " B" and thus not picking up the device correctly. Finally
add an adapter_khz setting in the OpenRD board configuration file - set
to 2MHz to match the Sheeva variant.
Confirmed as working thanks to Phil Hands providing me access to his
hardware to test on.
See also Debian Bug#793214; https://bugs.debian.org/793214
Change-Id: Ifacf53124eaa330bbbdf36dfa79e3256bf2a5201
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4254
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config covers the 4x Cortex A53 CPUs. A custom connector
is required from J14 to standard ARM JTAG on v1 boards. However
v2 hardware should have a standard FTSH-105-01-L-DV connector.
Pinmuxing code to enable JTAG pins is included in l-loader-poplar
repository, so board is flashed with open source code, JTAG
is available at very early boot. Alternatively the following
pokes can be issued from U-Boot to enable JTAG (e.g. to debug
hisilicon SDK).
mw 0xf8a210ec 0x130;
mw 0xf8a210f0 0x130;
mw 0xf8a210f4 0x130;
mw 0xf8a210f8 0x130;
mw 0xf8a210fc 0x130;
mw 0xf8a21100 0x130;
Change-Id: I2b83dfcb3dc5461c1620f94dd99aa7b31fdda59b
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-on: http://openocd.zylin.com/4161
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
in some cases we need something to test if uart is actually
properly connected.
Change-Id: I5a16b053164b34bb30ae8370753be12887a85c51
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Finally we can use this driver by default!
Change-Id: I09d215d1bd1dc16873a7379637e6869af65ad8f1
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4193
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
TDO and TMS: Safest values given it's an evaluation board
and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
high impedance (tri-stated).
Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.
See also Debian Bug#837989; https://bugs.debian.org/837989
Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
As found on the NI Project Sulfur SDR board.
Change-Id: I47bdd38ae85cf45cedad8797ea03bf3105153320
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4176
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Active watchdog forces reset during armv7m_checksum_memory()
in verify_image command if run just after reset init.
COP watchdog in KL series and WDOG32 in KE1 series
have longer timeout however they need to be disabled too.
The change extends 'kinetis disable_wdog' command to optionally
probe the chip and use appropriate algorithm to disable watchdog.
Setting of cache type is also split from flash_support flags.
Tcl command 'kinetis disable_wdog' is called in reset-init event.
Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3901
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3925
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Config file renamed to ke0x.cfg and a notice added to texi.
While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG.
Removed per device configs as they set CHIPNAME and nothing more.
Let's use reasonably universal chip name 'ke' set in family config.
Change-Id: I313db87a59f25f968eb3c27df155780b67becee8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3897
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3896
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds the file ti_beaglebone-base.cfg as the common base
configuration for all TI BeagleBone derived boards. It also modifies
ti_beaglebone.cfg to source the base board and only add the on-board
JTAG adapter. Lastly, it adds a file ti_beaglebone_black.cfg with
a suitable configuraton for the BeagleBone "Black" variant.
Change-Id: I40cacb8abed7bdb308929713891f7b5e5b685c95
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3099
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
configuration covers all 8 Cortex-A53 cores and auxiliary Cortex-M3
used for power management.
Change-Id: I5509f275aa669abe285f9152935ecdcbcd0c402e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4009
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with a Dresden Elektronik deRFmega128 module.
Change-Id: I91da3b11b60e78755360b08453ed368d6d396651
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2790
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit 25d7ba19c9 introduced a problem
with 'reset halt' due to setting srst_pulls_trst:
Error: cortex_m.c:595 cortex_m_halt(): can't request a halt while
in reset if nSRST pulls nTRST
Sorry, I don't know why I overlooked it when I tested #3722.
Change-Id: I41e9473dd91a86d93cf3e78b1fbbdfe1dd188d83
Reported-by: Ladislav Laska <laska@kam.mff.cuni.cz>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3942
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This seems to be a leftover from borrowing from omap3* configs. Since
SJC is not enabling or disabling the DAP tap, and the tap is always
available, the extra tapenable command causes warnings on startup
(can't enable what's already enabled).
Change-Id: I7514436d565aa5b91876dbdab547956f36dcab77
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3892
Tested-by: jenkins
This patch contains configuration for the twr-vf65gs10 system module
of the Freescale (NXP) tower system. It provides support for both the
CMSIS-DAP available via USB and the Cortex+ETM connector
on J5. The configuration also contains DDR and clock init code
hooked into the reset-init event handler.
Change-Id: I68303e0038e137dcadc57525e662428769fb69f2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3564
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Chip ID and flash layout taken from
Atmel-11102F-ATARM-SAM4C32-SAM4C16-SAM4C8-SAM4C4-Datasheet_27-Mar-15
and tested on a SAM4C32-EK (rev A).
Change-Id: I68aae5b60994c0b5964ea9031d40bc76ba025675
Signed-off-by: Owen Kirby <oskirby@gmail.com>
Reviewed-on: http://openocd.zylin.com/3527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target tcl to enable debugging of ARM Cortex-A5 on ADSP-SC58x
Change-Id: I378f8b94b7d6d6b9d0567985abc0e36aea7c8dea
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/3125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Remove comment about workaround of not working 'reset halt' - not needed
as 'reset halt' is working as expected @ EDBG with srst_only.
Add srst_pulls_trst to reset_config as it no more triggers an error.
Change-Id: I47cf445690c46ccfb866900cddbfcaefc8649f82
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3722
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Purge all legacy interface configurations so there's no more confusion
over which one to use.
Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.
Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
At least on my (phyCORE-AM335X) system, the AM335x watchdog
needs to be disabled to use OpenOCD for more than 6.5 seconds
after reset.
Change-Id: I3d883a9f572b0ccb92f9864853a00c372e39d7f2
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Reviewed-on: http://openocd.zylin.com/3391
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Instead of updating these regularly we can just accept any IDCODE for the
boundary scan TAP.
The only downside might be that it's not immediately obvious if you
source a config for the wrong type of STM32.
Change-Id: I96d4d81699a491b3a46de3f0d3fd078ffddad4e4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3385
Tested-by: jenkins
Both boards use SEGGER interface.
nRF52 flash driver is in change 3511.
The board files were needed for transport select to SWD. The default
jtag transport didn't failover to SWD.
Change-Id: Id9c72aa88eeeb6a4e1999ee182f5284dbe535c05
Signed-off-by: Rick Foos <rfoos@solengtech.com>
Reviewed-on: http://openocd.zylin.com/3600
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Michael Dietz <mjdietzx@gmail.com>
Reviewed-by: Jiří Pinkava <j-pi@seznam.cz>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The Linksys WAG200G router has a TI AR7 SoC and a 4MB Flash layout
similar to the Netgear DG834v3 router [1].
Below is an example of a successful flash recovery, using a TUMPA,
connected to the MIPS EJTAG 2.6 header (JP102) of the router.
WAG200G [2] TUMPA [3]
Desc Pin Pin Desc
------------------------
nTRST 1 3 nTRST
TDI 3 5 TDI
TDO 5 13 TDO
TMS 7 7 TMS
TCK 9 9 TCK
nSRST 11 15 RST
GND 2 4 GND
Note that nSRST is optional to halt the CPU, but is required to probe
the flash. For instance, recover the kernel with:
$ sudo ./src/openocd -s tcl \
-f interface/ftdi/tumpa.cfg \
-f tools/firmware-recovery.tcl \
-c 'board linksys-wag200g;
reset_config srst_only;
flash_part kernel /path/to/kernel.bin;
shutdown'
[1] https://wiki.openwrt.org/toh/linksys/wag200g
[2] https://www.linux-mips.org/wiki/JTAG#JTAG_headers
[3] http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual#20_PIN_JTAG_Connector
Change-Id: I952ba9f706e2e4f8f95ca03a5fa58f391ca030b6
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-on: http://openocd.zylin.com/3776
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis driver checks MDM STAT register to detect secured state of MCU.
Original version often reported a blank device as secured one.
Change #3010 has not fixed all false reports.
After changes in arm_adi_v5 infrastructure secured devices was not detected
at all.
New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and
MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop
are detected reliably.
Detection is run in both kx.cfg and klx.cfg from examine-start event,
not examine-end as before. Event is configured only for non hla adapter.
Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init.
Such frequency is not supported in VLPR CPU mode and with JTAG.
Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3547
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
XDS100v3 is software compatible with the XDS100v2, but has a
different usb pid. This commit adds `xds100v3.cfg` that sources
the v2 one and changes the usb pid.
Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80
Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com>
Reviewed-on: http://openocd.zylin.com/3632
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MBFTDI is a very cheap FT2232-based JTAG adapter
for programming Marsohod FPGA board.
Please see http://www.marsohod.org/prodmbftdi for details.
Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/3604
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Increase workareasize when it is know we have a larger device.
Change-Id: Ieaee92e7cd25cc201989f14de122349698871412
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3378
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
PSoC4 design prevents reset halt/init with standard/low level
SWD adapter if hw reset line configured. Give user hint
to use 'reset_config none' in such case.
Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3617
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The IDCODE of Artix7 15T in the UG470 is wrong; Artix7 35T and 15T don't have the same IDCODE.
I've tested this on real hardware.
Change-Id: Iac267dc449c23454dd119126749dbeb8267c18ac
Signed-off-by: Felix Held <felix-openocd@felixheld.de>
Reviewed-on: http://openocd.zylin.com/3633
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Allow using physical addresses with mem2array and array2mem. In order
to minimize the impact on existing scripts, "phys" is added as an
optional 5th parameter to both commands.
This patch also adds "phys" variants to the memwrite/memread commands
in memory.tcl.
Change-Id: Ia6307f9d861789e7f3ccf1f98961d666bf8d85d6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3387
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
add "mrb" command to read a byte of memory into a variable
Change-Id: I5ddc9fbcc55958a249548627bd15824df6dc0d61
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3542
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Just like observed with the General App Kit earlier, it now started to
fail halting:
SWD IDCODE 0x2ba01477
TARGET: xmc4500.cpu - Not halted
in procedure 'reset'
in procedure 'ocd_bouncer'
SWD IDCODE 0x2ba01477
Halt timed out, wake up GDB.
Rely on the target's default sysresetreq behavior to allow flashing to
work seemlessly again.
Change-Id: Ib9ce5f2c0ab99dca6d0fc74435fe26a58437fae5
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3416
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with TI MSP-EXP432P401R LaunchPad, via both on-board XDS110-ET (swd)
and external J-Link (jtag).
Change-Id: Ic0caa8516a155754b1c88a04acc8d3c511d9a5f7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3485
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The current configuration leads to the following error when trying to
program the target:
SWD IDCODE 0x2ba01477
timed out while waiting for target halted
TARGET: efm32.cpu - Not halted
in procedure 'program'
in procedure 'reset' called at file "embedded:startup.tcl", line 478
in procedure 'ocd_bouncer'
Use the default reset handling of the target (SYSRESETREQ) to reset the
system rather than SRST to fix the problem.
Tested on EFM32GG, EFM32TG and EZR32WG STK.
Change-Id: I788c41baf08b20814cbe0934b563424c4bc144b8
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3420
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Both the STM32F429I-DISC{O,1} boards are equipped with the same MCU, but
differ by the debugging chip:
- the STM32F429I-DISCO uses the ST-LINK/V2 chip;
- the STM32F429I-DISC1 uses the ST-LINK/V2-B chip (which matches the USB
VID/PID set in stlink-v2-1.cfg).
Change-Id: I07d637f72d26cf5d714472638da974eb6ca02325
Signed-off-by: Samuel Martin <s.martin49@gmail.com>
Reviewed-on: http://openocd.zylin.com/3492
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Leading zeros for the serial number are not necessary anymore.
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Change-Id: Ie4ff47b9cda7ccf314c6fda9a2784947db5ee4d9
Reviewed-on: http://openocd.zylin.com/3401
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Spansion FM4 family of microcontrollers does not offer a way to
identify the chip model nor the flash size, except for Dual Flash vs.
regular layout. Therefore the family is passed as argument and
wildcard-matched - MB9BFx6x and S6E2CC families are supported.
Iterations showed that ...
1) Just doing the flash command sequence from SRAM loader code for each
half-word took 20 minutes for an 8 KB block.
2) Doing the busy-wait in the loader merely reduced the time to 19 minutes.
3) Significant performance gains were achieved by looping in loader code
rather than in OpenOCD and by maximizing the batch size across sectors,
getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB.
(Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.)
gcc, objcopy -Obinary and bin2char.sh are used for automating the
integration of hand-written assembler snippets.
Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The reset-init hook for this target speeds up the CPU clock and JTAG adapter
speed. When the target is reset running with high adapter speed, a series of
warnings "DAP transaction stalled (WAIT) - slowing down" will be generated
since the adapter speed is not reduced to fit the slower CPU speed.
Fix: reduction of the adapter speed before a reset is performed.
Change-Id: Iabfc8e3f70311e0e71c8eed09b8a37fcbed9c58d
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for the Intel Quark mcu D2000 using the new quark_d2xx
target.
Changes to the lakemont part are needed for the D2000 core and
backwards compatible with the X1000 one.
Change-Id: I6e1ef5a5d116344942f08e413965abd3945235fa
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3199
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
niietcm4_write() buffer padding:
add correct buffer padding for 16 bytes.
Args check in FLASH_BANK_COMMAND_HANDLER():
first version of the driver had 7 args, current - 6. This patch will fix
error when flash is rejected (current k1921vk01t.cfg has flash bank init
with 6 args).
Timeouts in flash flag checking procedure:
increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check()
cause there were problems in some hardware configurations.
JTAG ID:
wrong id in k1921vk01t.cfg replaced with right one.
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Change-Id: I84296ba3eb4eeda4d4a68b18c94666f1269a500f
Reviewed-on: http://openocd.zylin.com/3171
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch fixes the tap order so that it matches the actual jtag
chain when all taps are enabled. It also introduces a variable
DEFAULT_TAPS that can be set outside of this script, e.g. on the
command line, to specify which taps are to be enabled on init.
Lastly, a new debug target "am335x.m3" is added so that the Wakeup-M3
can be selected for debugging.
Change-Id: Iccf177fda8d5e3737b1b2bb8fd1eaa7d3262ed9f
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with "J-Link OB RX621-ARM-SWD V1 compiled Nov 4 2014 10:47:22".
Change-Id: Ib64c0be407f99df57f058a4498556fd5ab7e9112
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3170
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested with Relax Kit for 5V Shields:
J-Link Lite-XMC4200 Rev.1 compiled Oct 14 2015 10:14:50
and with Relax Lite Kit:
J-Link Lite-XMC4200 Rev.1 compiled Oct 14 2015 10:14:50
Derived from xmc4800-relax.cfg.
Change-Id: I4e10fb6ed1f85168634d3b5259d3041ffc6b74d8
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3130
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds docs, example config, flash driver.
Driver is only supports K1921VK01T model for now.
Change-Id: I135259bb055dd2df1a17de99f066e2b24eae1b0f
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Reviewed-on: http://openocd.zylin.com/3011
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Base config without flash support for now.
Change-Id: I96a5b6ad35e00dc706177ea9dbdffc384ae7f62b
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3110
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The pflash.0 bank should not be present as it overlaps with
the flash bank created by target/kx.cfg, triggering an error.
This is also in line with the existing twr-k60f120m.cfg.
Change-Id: I5f620e01319d967f12e029fb6865ccdd031713b3
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3108
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
16000kHz is only safe after PLLs have been locked
properly. Until that's done (with reset init), we
can only safely run at 1000kHz.
Change-Id: I4e0a17e88aa9919cd6c34d44da68e23115c0d3a3
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/3015
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added interface config file for the FTDI FT232H based UM232H module.
This should work with UM232H-B too, an even cheaper module, but
that has not been tested.
Change-Id: Ifc312d6741da0b7862fe07d854023190d7afe251
Signed-off-by: Ragnar Sundblad <raggesu@gmail.com>
Reviewed-on: http://openocd.zylin.com/3031
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I232d769d893d54e4ea9411c46c56b19587b69919
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2707
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with cmsis-dap using the EDBG chip on the board.
Change-Id: I3d398685c81e4701a9f6c1a66e60f7a87f839daa
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/3092
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New configuration for NXP LPC4370 which consists of a Cortex-M4
and two Cortex-M0 cores.
Change-Id: I9918e3ff33218a14a99e4bbab9dce2e7b45b4d96
Signed-off-by: Jim Norris <u17263@att.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2124
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This reverts commit 7d7a43fd36.
The change concerns the "Black" variant of the TI BeagleBone, while the
configuration file is for the original BeagleBone board, which actually
embeds a debug interface on the PCB.
Change-Id: I2232af210deb698f8b3c0a547f26cd0a0a8f89d0
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3094
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: La Fonera FON2200
Change-Id: Ibfdbfc9c2beca6cf436c9ee5e493b08bfb55ac85
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2839
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: Netgear WP102
Change-Id: Id93957b5d5851a272f15be35f9f448a9ce6d8a08
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2835
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since 2cbbe9a it was actually decreasing the configured work area size.
We could now do "set WORKAREASIZE 0x2000" before sourcing lpc4350.cfg,
but there seems no point in doing so. Simply drop the configuration here.
Change-Id: I25b9dbbc007ba652b66099832198b7c329929858
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3086
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Default to lpc8xx as before, but allow setting the actual CHIPNAME.
Change-Id: I5a48fa75c640440a0d4c3f2858653e94bed846d2
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3084
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Board files should not select the interface. The BeagleBone Black is not
limited to just one JTAG interface.
Change-Id: I71ccc3dd9e2ca331a436701fab04e548b0abf829
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3083
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Adapted from diolan_lpc4350-db1.cfg. Both boards are identical except
for the SoC, so keep them in sync.
Change-Id: If892d8e953b0e3a9209a95b3b23a547357c10b7a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3038
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reuse the flashless LPC4350 as base and amend it as necessary.
The LPC43x7 have 2x 512 KB of flash.
Change-Id: Ia7ffbc7101023479971984b839f171ed4be6b089
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3037
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add support for the JTAG TAPID found on SK-FM4-U120-9B560-MEM V1.1.0 board.
Change-Id: Idbfe28927e0c549f0c89c29904d23971281927c9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3039
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It is found on the SK-FM4-U120-9B560-MEM V1.1.0 among others.
Change-Id: I4c708c9391e954cbbc8d0860a2a2dbd264aea865
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3008
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Its memory layout is different from MB9BFxxx.
Change-Id: I39c9f9cf582cd182971a9f83bb88c7a18da6cf15
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3007
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The xCORE-XA Core Module board has an XS1-XAU8A-10 SoC with 8 xCORE cores
and one ARM core. This config is for the ARM Cortex-M3, via J-Link OB.
Tested with "J-Link OB-STM32F103 V1 compiled Feb 5 2014 13:48:52".
Change-Id: Id7fadf8f323b45d5cfc0cae1054bd7b916771d6a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2763
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The XS1-XAU8A-10 has 8 xCORE cores and one ARM core.
This config represents the ARM Cortex-M3 core, which is apparently
Silicon Labs EFM32 Giant Gecko IP.
Change-Id: I998360f096c759d2e274d96c1ca2e0450ba61146
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2762
Tested-by: jenkins
Reviewed-by: Oleksij Rempel
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Most Xilinx FPGA devices contain an embedded, unique device identifier
called the "Device DNA". The identifier is nonvolatile, permanently
programmed into the FPGA, and is unchangeable providing a great serial
/ tracking number.
Debugging was done in https://github.com/timvideos/HDMI2USB/issues/36
Change-Id: Iad03eafb40887f0321a4dc22858a7c3bf37a12b3
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2960
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Another board supported by the ixo-usb-jtag project.
Change-Id: I676197c64e208886bc03d1bafcc964ef1fc2160b
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2963
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The board is supported via the ixo-usb-jtag firmware.
Change-Id: I1e8a5ead850c0843b8532a5b54a7e7117778278e
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2962
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also add further documentation about the project and how to use it.
Change-Id: Ia9878de566b3c8c1ea29f129287d5aea904d861d
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2961
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Flash driver "mini51.c" and "nuc1x.c" are same target MCU.
This patch integrates each driver and functions,
and makes into new "NuMicro" flash driver.
Change-Id: Ifff5c1cfdd265acca0f489631695be9194fa144c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A target config and a simple flash driver for the ADuCM360 microcontroller.
The EEPROM of the chip may be erased and programmed.
Change-Id: Ic2bc2f91ec5b6f72e3976dbe18071f461fe503b8
Signed-off-by: Ivan Buliev <i.buliev@mikrosistemi.com>
Reviewed-on: http://openocd.zylin.com/2787
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Tested with Porcupine-1 JTAG adapter board and Digilent JTAG-HS3 interface;
reset does not yet work, pending nSRST configuration of the interface used.
Change-Id: I0d0679e098d93ffbd1539004cdb900e2a8ae4a25
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2730
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As found on the Parallella-I board SKU A101020.
Change-Id: Ie7e7a36325926d67fbe555b46a9be8a74fac8dba
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2729
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Derived from tcl/interface/digilent-hs1.cfg.
JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with
PS_SRST_B on Xilinx Zynq SoC.
Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2728
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the chip IDs corresponding to the new 5V "SAMC" parts which are
otherwise identical to the SAMD and should work with this driver. Also
add the configurations for their Xplained Pro boards.
Change-Id: Ic268d4ac384a3a77d4211a94da9f9faf4d8c0f7b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2809
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Pipistrello is a low cost FPGA board with a Xilinx
Spartan6 LX45, a SPI flash and onboard FTDI JTAG.
This board is a good example use case for the jtagspi
flash driver talking through a proxy bitstream.
Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2846
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This covers only the Cortex-A5 for now, not the Cortex-M4.
Change-Id: I739ec52b14b83d6e9f124ed61f8941502e481402
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2766
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
code polishing to be consistent with other scripts
Change-Id: Ib52a92f48df9d2bdf543792b856e33aa04dbebe3
Signed-off-by: Radek Dostal <radek.dostal@streamunlimited.com>
Reviewed-on: http://openocd.zylin.com/2779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reset stopped working with this setting.
Change-Id: I98e8fafa48e0ab65dce8110870be422edf7b2fdb
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2727
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Split TMS570 target into LS31/LS21 and LS20/LS10 targets.
Board for the TMS570LS20SUSB Kit, which uses the TMS570 Cortex-R4 MCU from TI.
Tested attaching.
Change-Id: I1a69ac1ed800d0d6b7f9860c19cbd149e3e47620
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2089
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds support for the new Atmel SAML21 family of low-power Cortex
M0+ devices. Their Flash controller is essentially the SAMDxx one so
the change consists of adding the new part IDs. Unfortunately the
device ID logic had a couple of mistakes in it that did not affect
anything on SAMD2x devices (due to 0 values expected there) but that is
a problem on L21, it's therefore addressed here and things should now
match the datasheets.
Tested on Amtel SAML21 Xplained Pro development kit against the included
SAML21J18A there. Also tested for regressions on a SAMD20 and SAMD21
using their dev kits.
Change-Id: I768f75e064b8656c15148730dacaa4c3acfc4101
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2690
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Antonio Borneo
Andreas Bolsch
Alberto García Hierro
Jonathan McDowell
Tarek BOCHKATI
Karl Palsson
Diego Herranz
John Pham
Tomas Vanek
Kevin Burke
Ulrich-Lorenz Schlüter
Jan Kowalewski
Alexandre Bourdiol
Hellosun Wu
Zale Yu
Marc Schink
Jiri Kastner
Evgeniy Didin
Edward Fewell
Alistair Francis
Ake Rehnman
Liming Sun
Marek Vasut
Anton V. Kirilchik
luca vinci
Leonard Crestez
Piotr Kasprzyk
Andreas Fritiofson
Icenowy Zheng
Christopher Head
Andreas Färber
Felipe Balbi
Al Dyrius
Marc Schink
Caleb Szalacinski
Omair Javaid
Alexander Kurz
Rocco Marco Guglielmi
Angus Ainslie
Moritz Fischer
Peter Lawrence
Rod Boyce
Oleksij Rempel
Jean-Christian de Rivaz
Steven Stallion
Paul Fertser
William D. Jones
Rohit Singh
Adam Bass
Guido Günther
Kevin Gillespie
Cody P Schafer
Dominik Peklo
Oleksij Rempel
Antony Pavlov
Tim Newsome
Bohdan Tymkiv
Matthias Welwarsky
Niklas Söderlund
Robert Jordens
Matej Kogovsek
Mateusz Manowiecki
Michele Sardo
Jonas Norling
Patrick Stewart
barthess
Pushpal Sidhu
elmot
Alexandre Torgue
Peter Griffin
Slowcoder
Grzegorz Kostka
Forest Crossman
Juha Niskanen
Jan Čapek
Jerome Lambourg
Matthias Welwarsky
Matthias Bock
Uwe Bonnes
Owen Kirby
Harald Welte
Rick Foos
Vivien Didelot
Sean Cross
Remco Bloemen
Felix Held
Samuel Martin
Ivan Meleca
Freddie Chopin
Andrew Kohlsmith
Ivan De Cesaris
Tim 'mithro' Ansell
Manuel Limones
Bogdan Kolbov
Jonathan Larmour
Felipe Balbi
Ragnar Sundblad
Rémi PRUD’HOMME
Jeff Ciesielski
Morgan Quigley
Jim Norris
Maxime Coquelin
Nemui Trinomius
Ivan Buliev
Christoph Pittracher
Andrey Yurovsky
Radek Dostal
Alex Ray