Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
This is supposed to replace big part of armv7m_trace.[ch], since
TPIU is not only the one implemented in Cortex-M3 and M4.
Change-Id: I7588d16cbefe9cdb371c52fb0aa5cdfb48518804
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5858
Tested-by: jenkins
If the command 'itm port[s]' is issued before 'init', the ITM can
not be programmed because OpenOCD cannot access the target yet.
The configuration is recorded and applied after target examine.
The current test to trigger the ITM delayed-programming is based
on the TPIU configuration. This is allowed because the only use of
ITM it so send data through TPIU.
In case of system TPIU, not belonging anymore to the target, there
is no more association between target ITM and system TPIU.
Add a flag to record the pending ITM configuration requested
before 'init' and test the flag to trigger the delayed-programming
of the ITM.
Change-Id: I101eb97a116d7925cd2ff068f3e8813fc008b08e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6029
Tested-by: jenkins
The change [1] guarantees that the value pointed by 'prescaler'
gets always set, even when the adapter does not support the
specific mode requested (e.g. sync), or during trace disabling.
This works fine with the code in armv7m_trace_tpiu_config(), but
requires all the parameters to be valid also to disable the trace
(with 'enable==false'), otherwise returns error on incorrect
parameters or even causes segmentation fault if pointers
'trace_freq' or 'prescaler' are NULL.
Another problem in stlink_config_trace(), not linked with [1], is
caused by a tentative to change the settings on an already enabled
trace; the trace is disabled before the new parameters are fully
validated and in case of invalid parameters the trace is not
re-enabled.
It would be more logical to first check all the parameters, then
disable the trace, change the settings and re-enable the trace.
Practically revert [1] by checking 'enable==false' at function
entry, then disable trace and exit without any further check on
the other parameters.
For the case 'enable==true', validate all the function parameters
then disable the trace, update the trace settings and re-enable
the trace.
Modify the caller armv7m_trace_tpiu_config() to initialize the
variable 'prescaler' to a safe value to avoid the issue targeted
by [1].
[1] commit 38277fa752 ("jtag/drivers/stlink_usb: fix SWO prescaler")
Change-Id: Ia6530682162ca2c9f5ac64301f2456f70cc07ed2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5934
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
pg315 of CoreSight Components:
It is recommended that the ITMEn bit is cleared and waits for the
ITMBusy bit to be cleared, before changing any fields in the
Control Register, otherwise the behavior can be unpredictable.
Change-Id: Ie9a2b842825c98ee5edc9a35776320c668047769
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6043
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target->endianness is initialized to TARGET_ENDIAN_UNKNOWN at 34 lines
below, before calling target_configure. This initialization is
redundant and not needed.
Change-Id: Iea2d5e17a13c1a8b0b209ba7c20043736b520ef6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Support reading names/status of all threads, as well as all registers that are stored on the stack.
Limited to RV32, no FPU.
---
* WIP
Change-Id: I09417c2e45748504be449d74c39ae0b6b311e277
* WIP
Change-Id: I975fa2cabbf43ccf64f5162337c394f9c8e3017f
* Import rbtreehash-list from gnulib.
The main change to get this to build was to remove 3 includes from
config.h (actual code change in configure.ac) because lib/Makefile.am
doesn't contain the correct flags to find the files referenced there.
Instead I sprinkled necessary includes throughout the source code.
This feels like less of a hack regardless, so hopefully that's OK.
I'm not actually using the new library. Just got it to build.
Change-Id: I824000d8be0b6f58b6f2036498b37c33f453515a
* Actually use linkedhash_map.
Moved some files around to get it to link. Also note I'm using a
different module than before. This is the one I want (I think right
now).
Change-Id: I6161bffd4b5f916602c33c1930be6e061cefe982
* Properly track TCB/threadid mappings.
Change-Id: I725abb96f880745d78c5634d5faff7385c2773e1
* OpenOCD no longer crashes reading rv32 freertos regs
Change-Id: Ia84502dbf007145995d4fba8661153ab7f58f26f
* WIP
The register values reported for threads that aren't the current thread
look believable to me.
Change-Id: I94b109565c8cc2029fa77657a7fc10291bcb36e3
* Correctly mark the current thread.
Change-Id: Id94ababb55a222292090e6465e47ebf92ca26291
* Try to make the build pass.
Change-Id: I0fddd10fe22c013464f9a1e106cd21470fa7afe1
Signed-off-by: Tim Newsome <tim@sifive.com>
* Exclude new gnulib files.
Change-Id: I8b95615908034124f2236422771b5079f3304e37
Signed-off-by: Tim Newsome <tim@sifive.com>
* Style fixes.
Change-Id: I4aef0b1d0b0e366893c740ab89756fe8ea033ddb
Signed-off-by: Tim Newsome <tim@sifive.com>
* Don't include string.h.
It breaks the i686-w64-mingw32-gcc build, which complains:
error: incompatible implicit declaration of built-in function ‘strndup’
Change-Id: I8d758fe092efa503e015f71f34721f2c44632516
Signed-off-by: Tim Newsome <tim@sifive.com>
* Hopefully fix mingw32 build.
Change-Id: I8703b834b5679588b3aa6602ae4add7258dbd879
Signed-off-by: Tim Newsome <tim@sifive.com>
* Include winsock2 in replacements.
Change-Id: I77cfc90736c771a3cdefb39062e6c5b59de52cd5
Signed-off-by: Tim Newsome <tim@sifive.com>
* Zero now gets the correct value.
Change-Id: Ia7da043439a82081629b8a5991ed8cbc382d5ac8
Signed-off-by: Tim Newsome <tim@sifive.com>
* Accommodate non-general regs on the stack.
Also refactor FreeRTOS a little to separate out target-specific code
from target-indepent code.
Change-Id: Icc74d85b24f35d069be091e32e23144573560e9f
* All registers now read sane values.
It appears that FreeRTOS wastes a space on the stack, where x0 would be
saved. Am I missing something?
Correctly read mstatus as it is saved on the stack as well. This same
mechanism should also work for FPU registers, although there's more work
to be done before we get there.
Change-Id: Iabacc3af2ab368aa7b9090c1ff719451a087b5ed
Signed-off-by: Tim Newsome <tim@sifive.com>
OpenOCD is based on a single main loop that schedules all the
activities.
At the execution of a TCL command, the timestamp is checked to
eventually trigger the polling of the targets. This means that by
executing a TCL command the polling can be triggered and detect a
change of target's state.
When openocd 'resumes' a target, the target can halt again by
hitting a breakpoint.
The 'resumed' event handler is started just after the target has
been resumed, but it triggers a polling before the execution of
its very first instruction.
If the polling finds the target halted, it will run the 'halted'
event handler, that will then be executed 'before' the pending
'resumed' handler.
In case of gdb, a 'continue' command will restart the target but,
polling (and halt detection) executed before the end of the resume
process will hide the halt. As a consequence, the gdb will not be
informed of the halt and will remains waiting as if the target is
still running without showing the prompt.
This can be verified by running on the target a firmware with a
loop, run openocd with a dummy 'resumed' event, and let gdb to set
a breakpoint in the loop. A 'continue' command will cause the
target to halt again by hitting the breakpoint at the next loop
iteration, but gdb will loose it and will not return the prompt.
openocd -f board/st_nucleo_f4.cfg -c \
'stm32f4x.cpu configure -event resumed {echo hello}'
arm-none-eabi-gdb -ex 'target remote :3333' -ex 'b *$pc' -ex c
Disable the polling while executing target's resume().
Document it and provide hints to developers to cope with future
implementation.
Change-Id: I3be830a8e7c2ef6278617cb4547a4d676b0ddeb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Габитов Александр Фаритович <gabitov@planarchel.ru>
Reviewed-on: http://openocd.zylin.com/6074
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Currently wp/rwp commands fail on 64-bit targets:
> wp 0xffffffff80001400 4
addr option value ('0xffffffff80001400') is not valid
Change-Id: I94d4af906b02b7bd463c8d79a6235a3646dfc434
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-on: http://openocd.zylin.com/6058
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure: do not make Capstone dependency automagic
This adds regular ./configure options to control dependency on the
Capstone disassembly engine. See [0] for the rationale.
[0] https://wiki.gentoo.org/wiki/Project:Quality_Assurance/Automagic_dependencies
Change-Id: I3e16dc5255d650aa1949ccf896b26dc96e522a75
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5985
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure.ac: fix build with libusb0 and without libusb1
Driver 'openjtag' requires both libftdi and libusb1.
The current check is incorrect and the driver is built when
libftdi is present with libusb0 and without libusb1, which causes
the linker to fail resolving the required libusb1 symbols.
Remove the check for libusb0 on driver 'openjtag'.
Create a new adapters group LIBFTDI_USB1_ADAPTERS to hold the
driver 'openjtag'.
Change-Id: I1f5e554b519e51c829d116ede894639cb55a26aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5989
Tested-by: jenkins
* doc: fix over/underfull hboxes in PDF
This adds some cosmetic changes to make the PDF User Manual look
proper.
Building it now requires Texinfo 5.0 which shouldn't be problematic
according to [0]. Commit 79fdeb37f4 is
effectively reverted.
[0] https://repology.org/project/texinfo/versions
Change-Id: I990bc23bdb53d24c302b26d74fd770ea738e4096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5995
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* contrib: rpc_examples: haskell: fix ftbs with current libraries
And get rid of some warnings along the way.
Change-Id: I8fdbe1fa304276be6b0f25249b902b3576aa3793
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5987
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Makefile.am: fix override of target 'check-recursive'
To prevent executing the Jim Tcl tests, the makefile's target
'check-recursive' has been overridden in commit 56d163ce79
("jimtcl: update to 0.77, the current version, enable only
specific modules").
This causes a runtime warning during build:
Makefile:6332: warning: overriding recipe for target 'check-recursive'
Makefile:5098: warning: ignoring old recipe for target 'check-recursive'
Instead of override the makefile's target 'check-recursive',
prevent the recursion by re-assigning as empty the variable
SUBDIRS for this specific target only.
Change-Id: I03d1c467eba42316a59aeed4612d6bdbe6211282
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 56d163ce79 ("jimtcl: update to 0.77, the current version, enable only specific modules")
Reviewed-on: http://openocd.zylin.com/5986
Tested-by: jenkins
* contrib: udev file for Cypress SuperSpeed Explorer kit
lsusb output:
Bus 003 Device 011: ID 04b4:0007 Cypress Semiconductor Corp.
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x0007
bcdDevice 0.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 114
bNumInterfaces 4
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 0
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 1 AT-commands (v.25ter)
iFunction 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x00
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 4
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 5
bInterfaceProtocol 0
iInterface 0
Change-Id: I62f0300199da3551c8774a4a5a4cd106a3ab2904
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3611
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: fix memory leak on multiple '-gdb-port' flag
In the odd case of multiple flags '-gdb-port' during 'target
create' or following 'configure', the new strdup()'ed value will
replace the old one without freeing it.
Free the old value (if it exists) before replacing it.
Change-Id: I1673346613ce7023880046e3a9ba473e75f18b8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6005
Tested-by: jenkins
* udev: fix permission for Ambiq Micro EVK's
Commit 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.") was
initially proposed as http://openocd.zylin.com/3429/ then replaced
by http://openocd.zylin.com/3980/
The initial proposal was for file '99-openocd.rules', in which
MODE="664" was the norm.
After merge of http://openocd.zylin.com/2804/ the new udev rules
in '60-openocd.rules' switched to MODE="660", but the evolution of
the above patch missed this change.
Switch udev rules of Ambiq Micro EVK's to MODE="660" and uniform
them to the rest of the file.
Change-Id: I4b4eea535184ee8569da3264bff4f1fafb5bce4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.")
Reviewed-on: http://openocd.zylin.com/6004
Tested-by: jenkins
* doc/style: fix doxygen error
Doxygen complains about non-closed nested comments:
doc/manual/style.txt:423: warning: Reached end of file
while still inside a (nested) comment. Nesting level 1
(probable line reference: 149)
This is caused by the string '/**' that is interpreted as the
beginning of a comment.
Escape the string to not let doxygen consider it as a comment
While there, replace @code/@endcode with @verbatim/@endverbatim to
properly render the line.
Change-Id: If2a27c4cf659326e317cc4ac8c0b313e97e40432
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5996
Tested-by: jenkins
* flash/nor/max32xxx: fix path of include file
The relative path should have three times '..'.
Issue identified by doxygen:
src/flash/nor/max32xxx.c:85: warning: include file
../../contrib/loaders/flash/max32xxx/max32xxx.inc not
found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Change-Id: Ie7b4948c6770b8acb9eff26e08eea32945ebb219
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5997
Tested-by: jenkins
* Doxyfile.in: fix build out-of-tree
When doxygen is built out-of-tree, it fails to find the generated
file startup_tcl.inc:
src/openocd.c:59: warning: include file startup_tcl.inc
not found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Add '@builddir@/src' to INCLUDE_PATH.
Change-Id: I51f2f6fe7224bba0f8b3db7219f9831de4e67139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5998
Tested-by: jenkins
* doc/manual/primer/jtag.txt: remove duplicated section name
The section name 'primerjtag' is used twice, causing doxygen to
complain:
warning: multiple use of section label 'primerjtag',
(first occurrence: doc/manual/primer/jtag.txt, line 107)
Rename one of them.
Change-Id: Id307915dbc51a7f647fab4fb28ab431e65344d61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5999
Tested-by: jenkins
* Doxyfile.in: exclude libjaylink from doxygen
When build using libjaylink as git submodule, doxygen includes the
libjaylink files and complains for multiple 'mainpage' comment
block, one in OpenOCD and the other in libjaylink:
src/jtag/drivers/libjaylink/libjaylink/core.c:37: warning:
found more than one \mainpage comment block! (first
occurrence: doc/manual/main.txt, line 1), Skipping current
block!
Exclude libjaylink submodule from doxygen.
Change-Id: I5e856817344c9f21f8c26f077a23c00b83cfbcb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6000
Tested-by: jenkins
* openocd: fix incorrect doxygen comments
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
* openocd: fix doxygen parameters of functions
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
* doc/manual/primer/autotools.txt: fix doxygen warning
Commit ab90b87778 ("configure: remove AM_MAINTAINER_MODE,
effectively always enabling all the rules") removes the configure
flag '--enable-maintainer-mode' and its documentation, but have
left a reference to the removed subsection 'primermaintainermode'
and this triggers a warning in doxygen:
doc/manual/primer/autotools.txt:21: warning: unable to
resolve reference to 'primermaintainermode' for \ref
command
Remove the obsoleted paragraph.
Change-Id: I56e69ef033d546d159745bed1b47c6105827e7ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ab90b87778 ("configure: remove AM_MAINTAINER_MODE, effectively always enabling all the rules")
Reviewed-on: http://openocd.zylin.com/6003
Tested-by: jenkins
* flash/stmqspi: fix build error with -Werror=maybe-uninitialized
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/flash/nor/stmqspi.c: In function ‘read_flash_id’:
/src/flash/nor/stmqspi.c:1948:6: error: ‘retval’ may be used uninitialized
Change-Id: Ifd8ae60df847fc61e22ca100c008e3914c9af79b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6012
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: fix build error with -Werror=maybe-uninitialized
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/target/riscv/riscv.c: In function ‘riscv_address_translate’:
/src/target/riscv/riscv.c:1536:13: error: ‘pte’ may be used uninitialized
Change-Id: I51e180b43f9b6996e4e4058db49c179b9f81bcdc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6013
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: [FIX] ARMv8-M does not support VECTRESET
ref: Arm®v8-M Architecture Reference Manual (DDI0553B.m)
D1.2.3: AIRCR, Application Interrupt and Reset Control Register
Bit [0] is RES0
Change-Id: I6ef451b2c114487e2732852a60e86c292ffa6a50
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6014
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* driver/ftdi: skip trst in swd mode
When using the adapter olimex arm-jtag-swd (to convert to SWD a
JTAG-only FTDI adapter), the pin trst on JTAG side is re-used to
control the direction of pin SWDIO on SWD side.
There is a single reset API at adapter driver to assert/deassert
either srst and/or trst. A request to assert/deassert srst can
cause also trst to change value, hanging the SWD communication.
In SWD mode, ignore the value passed to trst.
Change-Id: I5fe1eed851177d405d77ae6079da9642dc1a08f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6006
Tested-by: jenkins
* configure.ac: drop macro 'AC_PROG_CC_C99' from autoconf 2.70
The macro AC_PROG_CC_C99 has been obsoleted by autoconf 2.70 and
triggers a set of warnings from both 'aclocal' and 'autoconf'.
The test of AC_PROG_CC_C99 is now included in AC_PROG_CC.
For autoconf 2.69 and earlier the macro is still required, so
cannot be simply dropped.
Use a conditional test to avoid the warning on autoconf 2.70 but
still use AC_PROG_CC_C99 on older autoconf.
Change-Id: I5e8437f5a826fb63be6d07bcb5bb824f94683020
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6009
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* configure: drop macro 'AC_HEADER_TIME'
The macro AC_HEADER_TIME has been obsoleted by autoconf 2.70.
Not all systems provide 'sys/time.h', plus some old system didn't
allowed to include both 'time.h' and 'sys/time.h' because 'time.h'
was included by 'sys/time.h' and was not properly protected to
allow multiple inclusion.
The macro AC_HEADER_TIME helps to detect such odd case.
Nowadays all the systems properly protect 'time.h', so its safe to
unconditionally include 'time.h', even if it is also included by
'sys/time.h'.
The case of systems without 'sys/time.h' is already covered by
configure.ac through the directive
AC_CHECK_HEADERS([sys/time.h])
Remove the obsoleted autoconf macro and simplify the code by
including 'time.h' unconditionally and check HAVE_SYS_TIME_H to
include 'sys/time.h'.
Change-Id: Iddb3f3f1d90c22668b97f8e756e1b4f733367a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6010
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* README.macOS: explain how to install suitable Texinfo
Change-Id: Ic5906111f412eebd906a9be3fd0e133484def3eb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6026
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* jlink: fix device discovery when network is off
If user specifies a serial number for the jlink device, openocd
extends the search to network jlink devices too, without checking
if the host has a valid and functional network connection. If the
network is not functional, libjaylink returns error. This error
invalidates the discovery on USB, even if it was successful.
Factor-out parts of the jlink_init into separate jlink_open_device
function, use that function to firstly discover and match USB
devices and, if matching device was not found on the USB bus and
serial number was specified, repeat discovery and matching via TCP.
Fixes: https://sourceforge.net/p/openocd/tickets/294/
Change-Id: Iea0de1640d4e5b21ecc7e9c1dd6d36f214d647c2
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: http://openocd.zylin.com/6025
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* README: add missing items for 0.11
JTAG adapters
Cadence DPI, Cypress Kitpro, FTDI FT232R, Linux GPIOD, Mellanox rshim,
Nuvoton Nu-Link, Nu-Link2, NXP IMX GPIO, Remote Bitbang, TI XDS110,
Xilinx XVC/PCIe
Debug targets
AArch64, Cortex-M (ARMv8-M), ARCv2, MIPS64, RISC-V, ST-STM8
Flash Drivers
ATmega128RFA1, Atmel SAM, eSi-RISC, EZR32HG, MAX32, MXC, nRF52, PSoC6,
Renesas RPC HF and SH QSPI, SiFive Freedom E, ST BlueNRG,
STM32 QUAD/OCTO-SPI for Flash/FRAM/EEPROM, SWM050, TI CC13xx, TI CC26xx,
TI CC32xx, TI MSP432, Winner Micro w600, Xilinx XCF
Change-Id: I341618ac5d7189e4f98268cecd66c99447b72af8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6027
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* The openocd-0.11.0-rc2 release candidate
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* Restore +dev suffix
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* steppenprobe: fix file permission
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.
Strip the execution permission.
Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
* github: fix github wokflow while pushing a tag
this fix permits to add correctly the generated artifact (windows binaries)
into the release section.
Change-Id: Ia982370d3a1e08c623ebcabb5ac97e9fb49d00e0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* doc: Fix type in Hooking up the JTAG Adapter
We are talking about adapter connectivity in this chapter. It should
be "dongles" instead of "cables".
Change-Id: I7bd4307765517375caa2af86dfc929d0ef66c3e6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6040
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
* doc/manual: Fix @subpage handling
The subpage "thelist" used to have a title "Pending and Open Tasks"
but the commit c41db358a0 changed it to "The List". With
@subpage, it now renders:
"The List of The List enumerates opportunities for"
instead of
"The List of Pending and Open Tasks enumerates opportunities for"
This commit fix it to
"The List enumerates opportunities for"
Change-Id: Ifee0dcd9b3c9f7e651a8748a7afda99eedea3c5c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6041
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* doc/manual: Fix function name typo
We have both the singular form, register_command(), and the plural form
register_commands().
Change-Id: I905ea83988b8ac70dd809b02d53b646aa4d66697
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6042
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Co-authored-by: Paul Fertser <fercerpav@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Jiri Kastner <cz172638@gmail.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Co-authored-by: Bohdan Tymkiv <bohdan200@gmail.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Co-authored-by: Yasushi SHOJI <yashi@spacecubics.com>
* Fix in write_memory_bus_v1: Read sbcs properly
Fixed an issue with system bus write: sberrors were not properly
detected because of an incomplete read of "sbcs". The read was initiated
but not completed (value not acquired by a second DMI scan).
Added debug prints in case sberror != 0.
Added few comments to explain the algorithm.
Change-Id: Id5eb07f2f1bf8e9afee2dec04b9ff5c5a57f606b
Signed-off-by: Jan Matyas <matyas@codasip.com>
* Updated per review discussion at #577.
Change-Id: I65c07edcd4e86eaa5327280a81f74db0b9c84f9c
Signed-off-by: Jan Matyas <jmatyas@codasip.com>
* Empty commit to re-trigger Travis build.
Change-Id: I95deeb28584a891203c8904be621e48003f069dc
Co-authored-by: Jan Matyas <jmatyas@codasip.com>
This way people can write TCL scripts that rely on these more abstract
properties instead of having to check for the existence of sbaccess,
which is not part of 0.11. (There is a similar feature but things are
named differently.)
Change-Id: I5c95a29ef43cb40c3a73b904f11fa7ca38d87b21
Signed-off-by: Tim Newsome <tim@sifive.com>
I don't know how this worked before. Possibly caused by overzealous
removal of `-rtos riscv`.
Change-Id: I7259267b861ef45655f469ab39cc463d608fe149
Signed-off-by: Tim Newsome <tim@sifive.com>
* Make a few globals const.
Looking through globals to see what needs to be removed, but const
globals are OK.
Change-Id: I4126a3f629daf91b109a3bd7120e4b4f62a9d8ee
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix comment typo.
Change-Id: I0c20837559411410b6870e0d0e52c0179a3a167e
Signed-off-by: Tim Newsome <tim@sifive.com>
AFAIK there is no hardware that implements this, but it should be a
close-to-done starting point in case it is ever required.
Change-Id: I49e3082e8629b1d70b12e8a847c2848e75b04508
Signed-off-by: Tim Newsome <tim@sifive.com>
* Remove `-rtos riscv`.
`-rtos hwwthread` is target-independent and a cleaner way to achieve the
same thing.
Change-Id: I863a91f9ad66e37dc36f2fbcbffe403b91355556
* Little more cleanup.
Change-Id: I8fda2317368a94760bc734abc7f1de6ee5b82a7c
* Clean up some more.
Change-Id: I64a1e96aa3bd8c0561d4d19930f99e9bc40eab86
* Get rid of riscv_[sg]et_register_on_hart
Change-Id: I5ea9439bad0e74d7ed2099935e7fc7292c4a2b7f
* Remove hartid arg from set_register.
Change-Id: Ib560e3c63ff32191589c74d3ee06b12295107c6f
* Remove more references to hartid.
Change-Id: Ie9d932fb8b671c478271c1084dad43cad3b2bfbc
* Remove some unused code.
Change-Id: I233360c6c420d1fc98b923d067e65a9419d88d7b
Signed-off-by: Tim Newsome <tim@sifive.com>
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/target/riscv/riscv.c: In function ‘riscv_address_translate’:
/src/target/riscv/riscv.c:1536:13: error: ‘pte’ may be used uninitialized
Change-Id: I51e180b43f9b6996e4e4058db49c179b9f81bcdc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6013
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It doesn't have any effect on real hardware, and by caching the value we
pretended it did.
Fixes#564
Change-Id: I9f4e2cc8abddee61435bbd8d992cbff971a0c28d
Signed-off-by: Tim Newsome <tim@sifive.com>
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
The comment should refer to reading rather than writing.
Change-Id: I72937bb48053233ab5e48d343c4bd1e394f77bda
Signed-off-by: Craig Blackmore <craig.blackmore@embecosm.com>
In the odd case of multiple flags '-gdb-port' during 'target
create' or following 'configure', the new strdup()'ed value will
replace the old one without freeing it.
Free the old value (if it exists) before replacing it.
Change-Id: I1673346613ce7023880046e3a9ba473e75f18b8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6005
Tested-by: jenkins
The target code for assert reset on cortex_a has been patched on
commit b0698501b0 ("cortex_a: fix cortex_a_assert_reset() if
srst_gates_jtag") then in cdba6ba0ad ("cortex_a: fix reset for
SWD transport") to workaround the mismatch between jtag and swd
implementations. See discussion for the second patch at
http://openocd.zylin.com/3641/
While all of these mismatches should hopefully be cleaned by the
reset framework rework, an extension of the workaround of the
second patch is required for dapdirect transports, either
dapdirect_swd and dapdirect_jtag.
Extend the existing workaround to all non-jtag transports.
Change-Id: Ia6a9d43bab524cbb3de4c37ce24c45f25187353d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5979
Tested-by: jenkins
If OpenOCD is reading trace data from the target, at exit it
should stop the adapter to gather data, but should left the target
still producing them.
Add a helper in armv7m_trace to disable the adapter's trace and
call it during OpenOCD teardown.
This also provides a workaround for an issue in the firmware of
ST-Link V3 till version V3J7. If the SWD connection is closed when
trace is active, at following connection the trace does not work
anymore.
Change-Id: I47ccab61405384938555096c5aca789eaa090d27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5978
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Add `riscv info` command. Final output is "TCL format" and looks like this:
```
hart.xlen 64
hart.trigger_count 4
dm.abits 6
dm.progbufsize 2
dm.sbversion 0
dm.sbasize 0
dm.sbaccess128 0
dm.sbaccess64 0
dm.sbaccess32 0
dm.sbaccess16 0
dm.sbaccess8 0
```
* Add `riscv info` command.
This command displays some basic information that OpenOCD has detected
about the target. The output is displayed in YAML so it can easily be
parsed. Example of current output:
```
Hart:
XLEN: 32
trigger count: 4
Debug Module:
abits: 6
progbufsize: 2
sbversion: 0
sbasize: 0
sbaccess128: 0
sbaccess64: 0
sbaccess32: 0
sbaccess16: 0
sbaccess8: 0
```
Change-Id: If920c083ff6ec9f482c50f913cd8ceaa62461217
Signed-off-by: Tim Newsome <tim@sifive.com>
* Disable workflow inherited from upstream.
Change-Id: Ifc5ed1b4f5ec2278b8bcf3279c9fd462e469fefa
Signed-off-by: Tim Newsome <tim@sifive.com>
* Switch from YAML to TCL "set array" input format.
Change-Id: I3833210e5bf6d7cffc9934c04ec5201ae7732ad8
Signed-off-by: Tim Newsome <tim@sifive.com>
* Remove indent in `riscv info` output.
That was getting a little too cute, and probably more confusing than
helpful.
Change-Id: Ie51416f53ab4b69294962f0565767d370db82867
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix error handling in read_memory_progbuf_one().
Be sure to restore mstatus/s0 even if there is a failure during the
operation.
Fixes#559.
Change-Id: Ib86ca2c7455bad4a668f34703566060a782116db
Signed-off-by: Tim Newsome <tim@sifive.com>
* Style fix suggested in review.
Change-Id: I444112a9dffea483b7d0e5f96ef7bbdaf58d249f
Signed-off-by: Tim Newsome <tim@sifive.com>
This is a fix for an issue reported by Joe Stoy at:
https://sourceforge.net/p/openocd/mailman/message/37128537/
When clearing sbcs.sbbusyerror, preserve other bits in the sbcs
register that are needed for subsequent system bus transactions.
The use of 'void *' makes the pointer arithmetic incompatible with
standard C, even if this is allowed by GCC extensions.
The use of 'void *' can also hide incorrect pointer assignments.
Switch to 'uint8_t *' and add GCC warning flag to track any use of
pointer arithmetic extension.
Change-Id: Ic4d15a232834cd6b374330f70e2473a359b1607f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5937
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit 80f1a92bd7 ("mips64: Add generic mips64 target support")
adds a log of the target's program counter in function
mips_mips64_debug_entry() by directly casting the little-endian
buffer in pc->value.
This is going to print an incorrect value on big-endian hosts.
Use the function buf_get_u64() to return the register value.
Not tested on real HW. Issue identified with GCC compiler flag
'-Wcast-align=strict' after change http://openocd.zylin.com/5937/
("target/register: use an array of uint8_t for register's value").
Change-Id: Icbda2b54a03fdec287c804e623f5db4252f9cd2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 80f1a92bd7 ("mips64: Add generic mips64 target support")
Reviewed-on: http://openocd.zylin.com/5944
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The original code passes to ->read_core_regs() and to
->read_xpsr() the pointer to the little-endian buffer reg.value.
This is incorrect because the two functions above require a
pointer to uint32_t, since they already run the conversion with
arm_le_to_h_u32() in the jtag callback.
This causes a mismatch on big-endian host and the registers get
read with the incorrect endianness.
Use an intermediate buffer to read the registers as uint32_t and
to track the destination reg.value pointer, then copy the value in
reg.value after the call to jtag_execute_queue().
Tested with qemu-armeb and an OpenOCD built through buildroot
configured for cortex-a7 big-endian.
Note that if jtag_execute_queue() fails, the openocd register
cache is not updated, so the already modified flags 'valid' and
'dirty' are incorrect. This part should be moved after the call to
jtag_execute_queue() too.
Change-Id: Iba70d964ffbb74bf0860bfd9d299f218e3bc65bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5943
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Commit fc2abe63fd ("armv7m: use generic arm::core_mode") adds
two special modes for ARMv6M and ARMv7M in struct arm_mode_data[].
While these modes do not have any additional register to be dumped
by command 'arm reg', the command still prints an header for these
modes but not followed by any register.
Detect the special modes for ARMv6M and ARMv7M and skip them to
avoid printing the useless header.
Change-Id: I04145769e5742624f143c910eebf9a6f6d8e3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fc2abe63fd ("armv7m: use generic arm::core_mode")
Reviewed-on: http://openocd.zylin.com/5942
Tested-by: jenkins
Commit fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor
mode") introduces the secure mode 28 of ARMv6 as a synonymous of
mode 22 (MON), but does not add it in the switch/case in command
'arm reg'.
When command 'arm reg' scans the array arm_mode_data[] on targets
without secure modes, it does not detect the new secure mode as
not supported by the architecture, thus triggers a segmentation
fault when it try to read the register's value from unallocated
memory.
Issue detected with target arm926ejs.
Add the new mode in the switch/case and treat it as the mode MON.
Change-Id: I2b72cc558e097879a7ee6ea601200bfda6b60270
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor mode")
Reviewed-on: http://openocd.zylin.com/5941
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reading of DPIDR is the very first operation after JTAG to SWD sequence.
Without this change if DPIDR read fails then swd connect fails.
Keep trying JTAG to SWD sequence and DPIDR read until success
or timeout 0.5 sec. It makes setting of adapter srst delay on SWD transport
mostly unnecessary.
Also test for ERROR_WAIT (which should not occur according to
IHI 0031E B4.3.2 but a quirk is known) and if bus is kept stalled
then issue abort to make the next connect possible.
Change-Id: Id8fe6618605bbeb4fed5061e987ed55de90a35f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If dap_dp_read_atomic() in 30 trials loop fails, dap->do_reconnect is set.
Following dap_dp_read_atomic() calls dap_queue_dp_read() which in case
of SWD transport calls swd_queue_dp_read(). It starts
with swd_check_reconnect() and it calls swd_connect() because
dap->do_reconnect is set. swd_connect() does some initialization,
reads DPIDR and calls dap_dp_init() again!
Moreover if dap_dp_init() is called from cortex_m_reset_(de)assert()
one level of recursion is necessary to reconnect the target.
Introduce dap_dp_init_or_reconnect() for use in cortex_m reset
and similar.
Remove loop of 30 atomic reads of DP_STAT to prevent unwanted recursion.
Change-Id: I54052fdefe50bf5f7c7b59fe751fe2063d5710c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5729
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I4fea29f07f4d3b8b2578b538ef0eef5f1eea285f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5876
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a Cortex-M (not M0, M0+) target was stopped in the middle of
a conditional IT block or in the load/store multiple instruction,
cortex_m_debug_entry() used wrong xPSR bits to detect it and then
cleared 8 bits of the exception number from xPSR
- probably wrong bit mask again.
I believe clearing of the ICI/IT bits in cortex_m_debug_entry() has no
reason as Cortex-M does not use instruction injecting.
Remove the wrong code.
The change was originally a part of http://openocd.zylin.com/4862
It is now re-submitted as #4862 is not ready.
Change-Id: If91cd91d1b81b2684f7d5f10cf20452cde1a7f56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5874
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Consolidate low level register read/write.
Floating point registers were handled by target_read/write_u32
unlike other registers handled by cortexm_dap_read/write_coreregister_u32
There is no reason to do so in cortex_m.
Remove cortexm_dap_read/write_coreregister_u32
and use cortex_m_load/store_core_reg_u32 directly.
Similarly HLA adapters register read/write interface supports all registers
so use it for any floating point and other registers.
Change-Id: Ida679e5f4fec02d94ffb0bd3f265ed7ed2221cdc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5864
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move primask/basepri/faultmask/control packing/unpacking from
cortex_m.c and hla_target.c to armv7m.c armv7m_read_core_reg()
and armv7m_write_core_reg() where also the FP 32/64-bit registers
conversion takes place.
Introduce a new hidden register ARMV7M_PMSK_BPRI_FLTMSK_CTRL
for packing/unpacking of special registers in the register cache.
The new packing/unpacking is endianess safe.
While on it improve returned error codes and LOG_ messages.
Just minimal changes in cortex_m.c and hla_target.c, will be
consolidated in the next patch.
Change-Id: Id51e764e243e54b5fdaadf2a202eee7c4bc729fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Make arm register id coherent with reg_list index.
Without this reg_list[ARMV7M_R12] was possible but
reg_list[ARMV7M_FPSCR] was out of bounds.
Remove unused items from reg_list index.
Change-Id: I84d3b5c496fc1839d07a5b74cb1fd1c3d4ff8989
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5862
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Define a new enum with DCRSR.REGSEL selectors.
Introduce armv7m_map_id_to_regsel() to unify mapping in one place.
Use DCRSR.REGSEL selectors for low level register read/write.
Change-Id: Ida0ccdfa9cdb1257a1900b8bfbf172b076374d39
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Introduce a 'hidden' flag in struct reg to support a register cache
containing different views of same data: e.g. Cortex-M has
primask, basepri, faultmask and control registers accessed
as one word. With the hidden flag we can add an reg_list item
corresponding to hw access without exposing the register to user level.
All the struct reg are allocated with calloc() but one in xscale.c
allocated by malloc(). Change this one to use calloc() as well
to guarantee initial value hidden=false
Change-Id: I8da9f5a5a60777ae7ef943a841307487bd80fc6f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5325
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
When the core is in sleep mode, the core is no longer retiring
instructions. Cortext M remains in "unknown" state. This patch converts
sleep mode to "running" state.
Change-Id: I1e9b6c9be51fd0f1f6ce81af9b1f5f9f1f43c661
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5921
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
The function arm7tdmi_clock_out() has one unused 'deprecated'
parameter.
Drop the unused 'deprecated' parameter and the FIXME above it.
Change-Id: Ia8de41f5b8258825faccc737bba622e44c81a7ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5912
Tested-by: jenkins
When a target examination fails, continue to examine subsequent targets.
Return the number of targets that failed to examine.
Change-Id: I883a0c445edc7eb00f496b79271d773771ec6b66
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When trace capturing the trace is enabled using 'tpiu_config internal'
(via the internal mode), OpenOCD can collect the trace buffers then append
it to a specified file or named pipe and propagate the trace to 'tcl_trace'
command.
This change is allowing OpenOCD to stream the captured trace over TCP.
When using this configuration OpenOCD acts like a server and multiple
clients can connect and receive the captured trace.
Example on STM32F7 running at 216MHz:
itm port 0 on
tpiu config internal :3344 uart off 216000000
Change-Id: Idea43e7e26e87b98a33da7fb9acf7ea50fe3b345
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5345
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
returning the created service seems useful:
as the only method to get the freshly created service is by getting the
last item in the services linked list, and this seems to be like an
intrusion to service internal mechanism.
possibly, we could get the service from a connection but this is possible
only from [new_connection|input|connection_closed]_handler_t, but this is
not always practical:
example: armv7m: add a TCP channel to stream captured trace
http://openocd.zylin.com/#/c/5345/
here we poll for trace and broadcast to all connections
outside of these xxx_handler_t functions
also, storing one of the connections in new_connection_handler_t and get
the service from it is possible, but this will make the code less readable.
Change-Id: I5fef1baecec1e054953c6faf5b99d864ecc97f02
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5717
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Functions that are not used outside the file should be declared as
static.
Change-Id: Ie81f6bdce91e2a1456364b47f30aa4d35c7ee7bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5900
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9f97571a528f0cb3c3c26f873577ab16fdec3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Is it possible to run OpenOCD without any target, for example to
only dump the rom-tables of an arm dap, or to perform low level
jtag operations.
But without any target created, the command 'target current'
causes OpenOCD to abruptly exit.
Handle in command 'target current' the case of no targets.
Change-Id: Ide15cb13bec84b88ccc3e7126523c04a6d70e636
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5881
Tested-by: jenkins
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
To avoid code duplication, reorganize the code to replace
cti_configure() with adiv5_jim_mem_ap_spot_configure().
Reorganize 'struct arm_cti_object' and its sub-'struct arm_cti'
moving DAP and mem-AP info in a 'struct adiv5_mem_ap_spot'.
Replace cti_configure() with adiv5_jim_mem_ap_spot_configure().
Deprecate the use of '-ctibase' in favor of '-baseaddr'.
Change-Id: I43740a37c80de67c0f5e4dc79c3400b91a12e9e8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5869
Tested-by: jenkins
This is somehow an extension of existing adiv5_jim_configure(),
but includes the 'address' in the mem_ap.
Rewrite adiv5_jim_configure() using the new helper.
Change-Id: Ia7effeeece044004d459b45126ed4961a98b8568
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5857
Tested-by: jenkins
Now that it’s possible to start profiling from either a running or a
halted state, rather than unconditionally halting after profiling
finishes, it makes more sense to restore the processor to whatever state
(running or halted) it was in before profiling started.
Change-Id: If6f6e70a1a365c1ce3b348a306c435c220b8bf12
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5237
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Cortex-M implementation of profiling contains a bunch of
conditionals and checks to handle both chips which have PCSR and chips
which do not. However, the net effect of the non-PCSR branches is
actually exactly the same as what target_profiling_default does. Rather
than duplicating this code, just detect the situation where PCSR isn’t
available and delegate to target_profiling_default.
Change-Id: I1be57ac77f983816ab6bf644a3cfca77b67d6f70
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are a handful of implementations of profiling. There is the
default implementation, which repeatedly halts and resumes the target,
sampling PC each time. There is the Cortex-M implementation, which
uses PCSR if available, otherwise falling back to halting and resuming
and sampling PC. There is the OR1K implementation, which reads NPC
repeatedly. Finally, there is the NDS32 implementation which uses some
kind of AICE commands with which I am unfamiliar.
None of these (with the possible exception of the NDS32
implementation) actually require the target to be halted when starting
profiling. The Cortex-M and OR1K actually resume the target as pretty
much their first action. The default implementation doesn’t do this,
but is written in such a way that the target just flips back and forth
between halted and running, and the code will do the right thing from
either initial state. The NDS32 implementation I don’t know about.
As such, for everything except NDS32, it is not really necessary that
the target be halted to start profiling. For the non-PCSR Cortex-M and
default implementations, there is no real harm in such a requirement,
because profiling is intrusive anyway, but there is no benefit. For
the PCSR-based Cortex-M and the OR1K, requiring that the target is
halted is annoying because it makes profiling more intrusive.
Remove the must-be-halted check from the target_profiling function.
Add it to the NDS32 implementation because I am not sure if that will
break when invoked with a running target. Do not add it to any of the
other implementations because they don’t need it.
Change-Id: I479dce999a80eccccfd3be4fa192c904f0a45709
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5235
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With help of actionpoint mechanism now it is possible to introduce
watchpoints support for ARC.
Change-Id: I5887335d0ba38c15c377bc1d24a1ef36e138cf65
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5867
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Bit 2 of control register is used if the processor includes the FP
extension
Change-Id: Ie21bc9de8cae5bad9d841e1908eff3aa0bb29d4b
Signed-off-by: Sylvain Chouleur <schouleur@graimatterlabs.ai>
Reviewed-on: http://openocd.zylin.com/5853
Reviewed-by: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This lets a user see exactly what period of time was sampled, without
having to guess how much time the target was ignored in between bursts.
Change-Id: I5c0639528636bf1a88f249be3ba59bec28c001e2
Signed-off-by: Tim Newsome <tim@sifive.com>
* Allow riscv_semihosting without 16 bit access to memory with instrustions
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* rename *_by_any_size to riscv_*_by_any_size
Used histogram diff strategy, which was much better than the default.
Conflicts:
doc/openocd.texi
src/flash/nor/fespi.c
src/jtag/drivers/libjaylink
src/rtos/rtos.c
src/target/riscv/batch.c
src/target/riscv/encoding.h
src/target/riscv/riscv-011.c
src/target/riscv/riscv-013.c
src/target/riscv/riscv.c
src/target/riscv/riscv.h
src/target/target.c
tcl/target/gd32vf103.cfg
Change-Id: I1321f62ba719419e58f93b2195f2540bd62f50d2
The commit b68674a1da ("Upstream tons of RISC-V changes.") was
proposed well before commit 3ac010bb9f ("Fix debug prints when
loading to flash"), but the merge got in different order.
After latest merge, the master branch fails to compile.
Fix the compile error.
Change-Id: Ia3bd21d970d589343a3b9b2d58c89e0c49f30015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5856
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
* Do not throw error if RISC-V tselect unimplemented
A RISC-V hart without Trigger Module may not implement any of the
associated CSRs such as tselect according to the specification.
riscv_enumerate_triggers previously threw an error in this case, but
only on the first invocation due to r->triggers_enumerated being set
regardless of this. Due to the propagation of this error condition to
disable_triggers and riscv_openocd_step, such a hart would remain
halted after the first 'step' (or 'continue') of a debug session.
This problem can be reproduced with the Ibex RISC-V CPU when
the DbgTriggerEn parameter is set to zero.
This commit changes the behavior of riscv_enumerate_triggers to
return ERROR_OK when tselect was not readable. This fixes the
described malfunction.
Change-Id: Ie813cb119b03702fe708801b5f3581f9bf337243
Signed-off-by: Tobias Kaiser <kaiser@tu-berlin.de>
* Add debug message if RISC-V tselect not readable
Change-Id: Ic3ad5bff9de5c50142cad983f351ce0099cec5c8
Signed-off-by: Tobias Kaiser <kaiser@tu-berlin.de>
* RISC-V triggers: continue if tselect is unreadable
In riscv_enumerate_triggers, even if for one hart tselect cannot be
accessed, other harts might provide trigger support. For this reason,
"continue;" is the appropriate action on a read failure of tselect,
which indicates that triggers are not implemented, instead of
"return ERROR_OK;".
Change-Id: Ied56f3e237b76195a15bfde159532eda9d347d21
Signed-off-by: Tobias Kaiser <kaiser@tu-berlin.de>
The function adiv5_jim_configure() casts the void pointer
'target->private_config' to a struct adiv5_private_config pointer.
This is tricky in case of aarch64, where the private data are in a
struct aarch64_private_config that has as first element the struct
adiv5_private_config.
While the current solution is working fine, it's not clean and
requires special attention for any further code development.
Override 'target->private_config' to the correct pointer while
calling adiv5_jim_configure().
Change-Id: Ic2fc047dd1e57013943d96e6d5879a919d1eb7b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5847
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change aarch64 to use ap-num setting if provided. Fall back to original
behavior of using first AP when ap-num is invalid.
Change-Id: I0d3624f75c86ba5fd5a322ac60856dbbb6e71eaf
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5831
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Add memory sampling feature.
Currently only gets 10 samples per second, but the overall scaffolding
looks like it works.
Change-Id: I25a2bbcba322f2101c3de598c225f83c902680fa
* Basic memory sample speed-ups.
977 samples/second.
Change-Id: I6ea874f25051aca1cbe3aa2918567a4ee316c4be
* Add base64 dumping of sample buffer.
We can't just dump raw data, because the API we use to get data to the
"user" uses NULL-terminated strings.
Change-Id: I3f33faaa485a74735c13cdaad685e336c1e2095f
* WIP on optimizing PC sampling.
1k samples per second on my laptop, which is roughly double what it was.
Change-Id: I6a77df8aa53118e44928f96d22210df84be45eda
* WIP
Change-Id: I4300692355cb0cf997ec59ab5ca71543b295abb0
* Use small batch to sample memory.
5k samples/second. No error checking.
Change-Id: I8a7f08e49cb153699021e27f8006beb0e6db70ee
* Collect memory samples near continuously.
Rewrite OpenOCD's core loop to get rid of the fixed 100ms delay.
Now collecting 15k samples/second.
Change-Id: Iba5e73e96e8d226a0b5777ecac19453c152dc634
* Fix build.
Change-Id: If2fe7a0c77e0d6545c93fa0d4a013c50a9b9d896
* Fix the mess I left after resolving conflicts.
Change-Id: I96abd47a7834bf8f5e005ba63020f0a0cc429548
* Support 64-bit address in memory sampling.
* Support sampling 64-bit values.
* Better error reporting. WIP on 64-bit support.
* Speed up single 32-bit memory sample.
21k samples/second.
* WIP on review feedback.
Change-Id: I00e453fd685d173b0206d925090beb06c1f057ca
* Make memory sample buffers/config per-target.
Change-Id: I5c2f5997795c7a434e71b36ca4c712623daf993c
* Document, and add bucket clear option.
Change-Id: I922b883adfa787fb4f5a894db872d04fda126cbd
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix whitespace.
Change-Id: Iabfeb0068d7138d9b252ac127d1b1f949cf19632
Signed-off-by: Tim Newsome <tim@sifive.com>
* Document sample buffer full behavior.
Change-Id: Ib3c30d34b1f9f30cf403afda8fdccb850bc8b4df
Signed-off-by: Tim Newsome <tim@sifive.com>
* Actually clear the sample buffer in dump_sample_buf.
Change-Id: Ifda22643f1e58f69a6382abc90474659d7330ac5
Signed-off-by: Tim Newsome <tim@sifive.com>
* Use compatible string formatting.
Change-Id: Ia5e5333e036c1dbe457bc977fcee41983b9a9b77
Signed-off-by: Tim Newsome <tim@sifive.com>
If a target is not examined, command vector_catch crashes while accessing
the debug_ap NULL pointer.
maskisr and reset_config commands don't require this check.
Change-Id: I949b6f6e8b983327dd98fbe403735141f8f0b5d6
Signed-off-by: Daniel Trnka <daniel.trnka@gmail.com>
Reviewed-on: http://openocd.zylin.com/5813
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* riscv: work around buggy hart states during reset in some DMs
As described in the comment this change adds, the GD32VF103 DM reports
that the hart is in more than one state while it is resetting. Because
of this, the current code acknowledges resets before they actually
complete. This sometimes prevents havereset from getting cleared as
intended, leading to a spurious "Hart 0 unexpectedly reset!" message the
next time riscv_is_halted() gets called.
To work around this, check for the absence of the unavailable state
rather than the presence of the running or halted states. This behavior
is also arguably more true to the spec than what exists now: Section 3.2
states that "The system may take an arbitrarily long time to come out of
reset, as reported by allunavail, anyunavail."
Change-Id: I34e90a16233125608bce8e4c2414dbead637600e
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* riscv: support custom reset-assert scripts
The reset-assert event is used, if present, to override the default
reset logic for ARM and MIPS cores. Do the same for RISC-V so that
devices with buggy ndmreset functionality (like GD32VF103) or
nonstandard reset sequences can specify the appropriate logic in Tcl.
Change-Id: I5e12077d67509853edb8ef3ad3f037f293a5fbb6
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* tcl/target: support GD32VF103 RISC-V MCU
The GD32VF103 is a low-cost 32-bit RISC-V microcontroller with
peripherals that are more-or-less compatible with the STM32F103 ARM
microcontroller. It is available on several low-cost dev boards, such as
the Sipeed Longan Nano, which is what I am testing on.
Add initial support for this chip, including a workaround for a buggy
ndmreset line (i.e. one that doesn't actually trigger a reset) in its
integrated debug module. Use the existing GD32VF103 flash driver that
was ported from the vendor's code in commit 48e40f3513 ("Add support
for GD32VF103 flash").
Change-Id: Iadac47ceb5437b8e18f3d35901388f10fef9f876
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* tcl/target/gd32vf103: add main flash alias
The GD32VF103 creates an alias to either main flash or the bootloader at
0x0, depending on how it was booted. As such, we want to indicate to
debuggers that the memory at 0x0 is flash and so cannot support software
breakpoints. To do this, add an alias to the main flash in the config.
This isn't strictly accurate in the case where we're running the
bootloader, but it still suits our purpose of fixing breakpoint
behavior.
Change-Id: I9eb8462d354f096eee231c0e5e2bffa538a5903e
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* Improve riscv expose_[csrs|custom] commands
* Add option to specify custom name for registers.
* Allow to call commands multiple times without loss of previous data.
* Make sure the commands can only be used in the config phase (before "init").
* Validity checks and warnings.
* Change commands to be per target.
* Fix memory leaks.
* Also fix unrelated memory leaks to keep valgrind happy.
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* fixes after review
* improve error message
This seems to be completely unused in these two files. It was probably
accidentally copied from riscv-011.c, where it is used.
Change-Id: I3f7ad8b2d26b005d3ea4438e2b3ec46a6c801792
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
These comments appear to have been copied from riscv-011.c, for which
they are accurate. However, it makes no sense to also have them in
riscv.c, because 1) none of the things described are actually in
riscv.c; and 2) riscv-013.c has an entirely different code structure,
meaning everything in the comment is an implementation detail of
riscv-011.c. Remove the copy in riscv.c and just leave the one in
riscv-011.c.
Change-Id: I2873af1522482681325525040b3caad2ddddce9d
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* Allocate RISC-V arch_info during target creation
* Ensured that target->arch_info is allocated as soon as the
target is created. Needed so that per-target config commands
(e.g. "riscv set_mem_access") can be executed also in the
OpenOCD's config phase (before calling "init").
* Added several assert()'s for safety.
Signed-off-by: Jan Matyas <matyas@codasip.com>
* Removed a TODO comment
* Allow to put breakpoints in memories without 16 bit access
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* tmp
* tmp
* tmp
* read/write by any size for breakpoints
* fix style for checkpatch
* Add flexible selection of memory access methods, detection of aampostincrement.
New configuration command introduced: "riscv set_mem_access".
It allows to specify which RISC-V memory access methods (progbuf,
sysbus and/or abstract access) should be tried and in which order
of priority.
Command "riscv set_prefer_sba" is left and works in backward
compatible way, but is marked as deprecated.
First time abstract memory access is executed, it is tried with
set aampostincrement bit. If the abstract command fails or the
address is not incremented correctly, aampostincrement will not
be used for any subsequent accesses.
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* remove unnecessary variable
* fix doc
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
In target/openrisc/jsp_server.c, an error is logged if the ptr was
already NULL. This cannot happen since the pointer was already
referenced few lines before and openocd would have been already
SIGSEGV in that case, so remove the log.
Change-Id: I290a32e6d4deab167676af4ddc83523c830ae49e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5809
Tested-by: jenkins
The prompt pointer in the jtag serial port is never zero'd or allocated.
Completely remove it since there is not much use for it as the target
software will provide the actual prompt.
Change-Id: Id95d8ccb9f725e53b9d03386b11d91eba1cd6ef4
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-on: http://openocd.zylin.com/4093
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: If10a0f1c254aee302b9ca08958390b7f21cdb21b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5824
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: I691094a6395acb0e4ea3bea2347ff38379002464
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5822
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
While there, fix prototype mismatch between header and C file of
the function armv7a_l1_d_cache_inval_virt().
Change-Id: I434bd241fa5c38e0c15d22cda2295097050067f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5818
Tested-by: jenkins
Commit 11019a824d ("adi_v5: enforce check on AP number value")
introduces the macro DP_APSEL_MAX and use it in place of hardcoded
magic numbers for the upper limit of AP selection value.
Use the macro also while defining the array of struct adiv5_ap in
struct adiv5_dap.
Change-Id: I88f53ceb710f92a48a8026a365709fbf2d9e6912
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5806
Tested-by: jenkins
While loading to flash with debug level at least 3,
OpenOCD tries to print the whole loaded bitstream.
This will be very-very-slow due to implementation of
conversion from buffer to string.
* fix condition on selected debug level in jtag/core.c
* replace slow buf_to_str function from helper/binarybuffer.c
with faster but_to_hex_str function
Change-Id: I3dc01d5846941ca80736f2ed12e3a54114d2b6dd
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
Reviewed-on: http://openocd.zylin.com/5800
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Make checkpatch require Signed-off-by
This will make it easier to send changes contributed here to mainline
OpenOCD.
(Intentionally not including the required line here to make sure I can't
just merge this.)
Change-Id: I089084d38f3e08859d62cf7eface405f37af4799
* Whitespace fix.
This PR isn't building on travis. Maybe because I only changed
.travis.yml. Here's a source change to force a build (hopefully).
Change-Id: I8a828fe1d56a1960bc4bfb91d3d2f3a0790ad571
* Can't check for signoff on sources alone.
Change-Id: I741a299b64bf14857a4e1807b254a7d270b2e466
Signed-off-by: Tim Newsome <tim@sifive.com>
* Actual whitespace fixes.
Why didn't this fail to build before?
Change-Id: I339c03c4ef96546dbef5f16e635921a4fdaf9b35
Signed-off-by: Tim Newsome <tim@sifive.com>
A ton of constants got a new prefix, so I made a lot of changes to
match, but no functional changes.
I did define DTM_DMI_MAX_ADDRESS_LENGTH in batch.c. That definition
never should have been in debug_defines.h, which I missed during code
review.
Change-Id: If5d86660f84bb0a3f2865fb36ef05d6630486d8b
Accessing registers on targets that implement 0.9 or earlier will no
longer work. If you need that we can talk about making it a config
option.
Change-Id: I953b639cf9a92ee9b0422e035da57c1d07504237
* WIP, apply stash with conflicts.
Change-Id: Ia794bde419aa29161c68898d20e30527e69f5a31
* Fix conflict resolution problems.
Change-Id: I4cedc348cf613f98cc5a36886f37c568ca644238
* Add repeat_read command.
Only implemented for sba v1 right now, and poorly tested at that.
Change-Id: I1d9ff63e1dea14b3f6a9f8ba4dad53668bf8038b
* Hide bogus address in repeat_read
Change-Id: Ib66c1fa60df9c7fc7cc87880b0fddc52825b48aa
* WIP make repeat read work with progbuf.
Change-Id: I555f8b880c8bf0d1ed0f3f90c7987a5b516a7a79
* WIP
Change-Id: Ic567cea68355ae907e94bd25185a2c9be6fd798d
* Fix error handling when increment is non-zero.
Change-Id: I5a2f3f2ee948fd4e12c0443a542e85b7b5c5791a
* Correctly(?) handle failures when increment is 0.
I'm not 100% convinced that this ensures every read value shows up in
the output, but it ought to work.
Change-Id: I1af3e7174cf9d5e6f293456fb5ead629e17faaaa
* Don't crash when asked to read no data.
Change-Id: I4061b5c720a43a4f828384ab9eacc89557adfa05
* Remove unnecessary comment.
Change-Id: I1be3d699b86299339b3a830ca1ef13c9f5b9fe0f
* Document `riscv repeat_read`.
Change-Id: I4a0f071f38784b2de034f8c1b0ce75d6d2d326b2
There are failure cases of target_create() that are not checked.
Plus, in case of failure the memory allocated in not properly
released before returning error.
Check all the possible failure in target_create().
Change current_target only when target is successfully created.
Add the new target to all_targets list only when target is
successfully created.
Release all the allocated memory before quit on failure.
Use malloc() instead of calloc() for target->type, because the
struct will be fully populated with memcpy().
Change-Id: Ib6f91cbb50c28878e7c73dc070b17b8d7d4e902f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5776
Tested-by: jenkins
If a target is not examined when the debugger tries to connect to it
then it can lead to undesired/undefined behavior.
In particular it leads to a zero pointer dereference on the aarch64.
Change-Id: I67f2b714ab8b2727fd36f3de16d7f9017b4c55fe
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5727
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There is no deinit_target method, so few memory allocations leak
at openocd exit.
Issue identified by tracking all calls to arm_dpm_setup().
Implement the method arm11_dpm_deinit() to free all the memory
allocated in arm11_dpm_init() and call it in the new
arm11_deinit_target().
NOT TESTED on real HW.
Change-Id: Icab86e290fc2db14f70eb84c8286357aadb02a35
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5694
Tested-by: jenkins
By default GDB timeouts after 2 seconds, even if this value can be
modified with GDB command "set remotetimeout".
On OpenOCD side, the default event for GDB attach is to halt the
target and wait it to halt. But here the default timeout of the
halt command is 5 seconds!
If the target cannot be halted (e.g. it's kept in reset by another
core or the debugger doesn't have enough privileges) then GDB will
timeout while OpenOCD is still waiting and is unable to
communicate with GDB.
Decrease the halt timeout to 1 second in the default GDB attach
event handler.
Change-Id: I231c740816bb6a0d74b0bc679a368a6cbfb34824
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5687
Tested-by: jenkins
There is no method to free the register cache, allocated in
arm720t_init_target().
Issue identified by tracking all calls to arm7tdmi_init_target().
Implement the method arm720t_deinit_target() by calling directly
arm7tdmi_deinit_target().
NOT TESTED on a real arm720t target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a xscale:
sed -i s/arm926ejs/arm720t/ tcl/target/spear3xx.cfg
Change-Id: I53c1f46c1a355a710e8df01468b19220671569dc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5697
Tested-by: jenkins
There is no method to free the register cache, allocated in
arm7tdmi_init_target(), so we get a memory leak.
Issue identified by tracking all calls to arm_build_reg_cache().
Implement the method arm7tdmi_deinit_target() that in turn calls
arm7tdmi_free_reg_cache().
NOT TESTED on a real arm7tdmi target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a arm7tdmi:
sed -i s/arm926ejs/arm7tdmi/ tcl/target/spear3xx.cfg
Change-Id: Iad465b708eb4ebb298725d7155fea76357e9045c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5696
Tested-by: jenkins
There is no method to free the register cache, allocated in
xscale_build_reg_cache(), so we get a memory leak.
Issue identified by tracking all calls to arm_build_reg_cache().
Implement the method xscale_deinit_target() that in turn calls the
new xscale_free_reg_cache().
Fix leak of struct xscale.
NOT TESTED on a real xscale target.
Tested on a arm926ejs (SPEAr320) by hacking the target type and
pretending it is a xscale:
sed -i s/arm926ejs/xscale/ tcl/target/spear3xx.cfg
Change-Id: Ibb2104c42411b76f4bb77c2fa387d1b85a3d2d5d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5695
Tested-by: jenkins
Similarly to the fix for arm926ejs (also base on arm9tdmi), fix
the other targets based on arm9tdmi.
The fix for arm926ejs is tested on SPEAr320 target.
This fix is proposed separately because is not tested on a correct
target device, but tested on SPEAr320 by hacking the target type
and pretending it is the correct one, e.g.:
sed -i s/arm926ejs/arm920t/ tcl/target/spear3xx.cfg
The memory leaks detected and fixed are:
- arm register cache;
- EmbeddedICE register cache;
- arm_jtag_reset_callback internal data;
- struct <target_type>_common.
Change-Id: I565f9a5bf144a9df78474434d86a64127ef0fbe5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5699
Tested-by: jenkins
Actionpoint mechanism allows to setup HW breakpoints and watchpoints on Synopsys ARC CPUs.
This mechanism is controlled by DEBUG register and by a set of auxilary registers.
Each actionpoint is controlled by 3 aux registers: Actionpoint(AP) match mask(AP_AMM),
AP match value(AP_AMV) and AP control(AC).
Note: some fields of actionpoint_t structure will be used in further
support of watchpoints.
Change-Id: I4efb24675f247cc19d9122501c9e63c3126fcab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Further deprecate `-rtos riscv`.
Now using `-rtos riscv` will result in a failure, which you can (until
the end of this year) bypass by adding `enable_rtos_riscv` to the
configuration.
Change-Id: Ic714c303dc1b00c19e8956609730c0f83c845cb6
* Make checkpatch happy.
Change-Id: I0469ec37d38ad2eadf25efb5b2b7ac88391c0f51
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_ARGUMENTS -f {} \;
This patch also fixes an incorrect function prototype in zy1000.c.
ZY1000 minidriver implementation overrides the function
arm11_run_instr_data_to_core_noack_inner(), but the prototype is
not the same as in src/target/arm11_dbgtap.c and to avoid compile
error it was changed also the prototype of the called function
arm11_run_instr_data_to_core_noack_inner_default().
Change-Id: I476cda8cdb0e1e280795b3b43ca95c40d09e4a3d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5630
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
It is an error to prefix with "0x" the print of values in decimal.
Replace the incorrect decimal format specifier with PRIx32.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types PRINTF_0XDECIMAL -f {} \;
Change-Id: I2eb867ef654527b2737ba573a405ec8f97c6a739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Technically that might be OK, but in practice it probably indicates
something went wrong somewhere. Before this change OpenOCD would crash
if it happened.
Change-Id: I2500ba67ec282915dcf2b2488f2aac9fbfdb23a3
Before commit b3ce5a0ae5 ("target: use LOG_USER to print errors
in events") an error in an event handler was silently lost, while
now the associated message is printed out.
A "shutdown" command in a target event (e.g. in gdb-detach) causes
the event to end with error code ERROR_COMMAND_CLOSE_CONNECTION,
that triggers the error message:
shutdown command invoked
Error executing event <event-name> on target <target-name>:
The error code returned by the command "shutdown" is required to
stop the execution in a script/proc and avoid executing any
further command in the script/proc.
It is then normal to get an error code from the "shutdown" command
and it should not be printed out.
Intercept the return code of the event in case of "shutdown", then
skip scheduling other target events and return without printing
the incorrect error message.
Change-Id: Ia3085fb46beacb90a5e4bf0abf7c6e28bb9e6a9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Laurent Lemele <laurent.lemele@st.com>
Reviewed-on: http://openocd.zylin.com/5710
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
With this commit we introduce L1 and L2 cache
flush and invalidate operations which are necessary for
getting/setting actual data during memory r/w operations.
We introduce L2 cache support, which is not presented
on currently support EMSK board. But L2 is presented
on HSDK board, which soon will be introduced.
Change-Id: I2fda505a47ecb8833cc9f5ffe24f6a4e22ab6eb0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5688
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When debugging an ARMv8-A/AArch32 target running HYP mode, OpenOCD would
throw the following error to GDB on most operations (step, set breakpoint):
cannot read system control register in this mode
The mode in question is 0x1A, a privilege level 2 mode available on cores
that have the virtualization extensions (such as the Raspi 3).
Note: this mode is only used when running in AArch32 compatibility mode.
Signed-off-by: Lucas Jenss <public@x3ro.de>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change-Id: Ia8673ff34c5b3eed60e24d8da57c3ca8197a60c2
Reviewed-on: http://openocd.zylin.com/5255
Tested-by: jenkins
Reviewed-by: Lucas Jenß <lucas.jenss@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This logic is a little tortured, but it still passes the semihosting
tests that were the cause for the recent rewrite.
Change-Id: Ic6760bb068621ab2a49feb0cf3998fc6957b5cfc
* Accommodate users setting custom triggers.
RISC-V hardware supports many more triggers than gdb can communicate to
OpenOCD. Accommodate users that set triggers by writing tdata* directly,
by disable/step/reenable when a user has done that.
Note that users must set dmode in tdata1 for this behavior to work
properly. Triggers with dmode=0 are assumed to be set and handled by the
software that is being debugged.
Change-Id: Ib0751689c5553aae3a273395b10f5b98326fa066
* Enumerate triggers when resuming from a trigger
Otherwise when we connect to a target that's already halted due to a
trigger, we won't correctly step past it.
Change-Id: I23b9482fa9597af826770f9cebf247b7ba59f65c
* Also disable/reenable triggers around single step.
Gdb is smart enough to disable/step/resume if it set the triggers, but
if a user set them manually it also needs to happen.
Change-Id: I1251bd47199b6f15f61a93e3a521a53f2b677c5f
* Fix whitespace.
Change-Id: Icc240aecbc7e3e36ce4e4d784f5703304334ca13
This fixes a regression introduced in "2dc88e1479f29ef0141b05bfcd907ad9a3e2d54c"
Change-Id: I04dc19ed30118a4c499b83732700b2ee0fdb67b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5610
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The name conflict is picked by compiler and it fails to compile for rv64
Fixes
src/target/riscv/riscv-011.c:1014:44: error: too many arguments provided to function-like macro invocation
static int read_csr(struct target *target, uint64_t *value, uint32_t csr)
^
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MULTILINE_DEREFERENCE -f {} \;
Change-Id: Icba05613e22a72ecc3e6a0aad7cb6b479496146f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5629
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
There is no method to free the register cache, allocated in
armv4_5, so we get a memory leak.
Issue identified by valgrind.
Implement the method arm_free_reg_cache() and call it in cortex_a
deinit and to exit for error during arm_dpm_setup().
Tested on dual cortex-A stm32mp15x.
This change is inspired from similar fix in commit b01b5fe13a
("armv7m: Fix memory leak in register caching.").
The same allocation is also used by target types "arm7tdmi",
"arm9tdmi", "arm11" and "xscale" but they all lack the deinit
method and I do not have relevant HW to test the fix. For such
reasons they are not addressed in this patch.
Change-Id: I4da1e1f12e36ec245d1f3b11a4eafcbd9a1d2e25
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5693
Tested-by: jenkins
The target mem_ap misses the method 'deinit_target' and does not
free the memory allocated during 'target create' and 'configure'.
Add the missing method and free the allocated memory.
Issue identified with valgrind.
Change-Id: If0d0114a75dd76a8b65c2d46d96c6085fd31a09d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5700
Tested-by: jenkins
Current code for Cortex M does not set C_DEBUGEN as soon as
possible, (which means during target examine), but later-on either:
1) at command 'halt' (e.g. for 'gdb-attach' event);
2) at command 'soft_reset_halt';
3) at commands 'reset', 'reset halt' or 'reset init';
4) during polling, but only if the target:
= enter in 'double fault', or
= exit from a reset, or
= halts (not possible if C_DEBUGEN is not set)
Plus, if commands in 1) or 2) are executed before the very first
poll of the target, the value of 'cortex_m->dcb_dhcsr' is used not
initialized while writing it back in DCB_DHCSR.
Another side effect of this situation is that it's possible to set
a HW breakpoint with the target running, while C_DEBUGEN is not
set. Accordingly to [1], C1.3.1 "Debug authentication":
When DGBEN is LOW and DHCSR.S_HALT == 0:
...
FPB breakpoints do not generate an entry to Debug state and,
if no DebugMonitor exception is generated, will escalate to
HardFault, Lockup, or be ignored.
On STM32MP15x I get HW breakpoint ignored, while on STM32F411 I
get HardFault.
E.g. following these steps:
- power-on a pre-flashed board that starts running the firmware;
- connect openocd, without halting or resetting the board;
- set a HW breakpoint to some address often executed;
- wait, but the board doesn't halt ...;
- type the command 'halt';
- if the Cortex-M has HardFault it would be visible and the fault
is at the breakpoint address;
- if no HardFault then type the command 'resume';
- wait and the board will finally halt at the HW breakpoint.
A similar issue has been detected on Cortex-A code and fixed by
commit bff87a7f28 ("target/cortex_a: enable DSCR_HALT_DBG_MODE
during examine").
Follow the same approach and set C_DEBUGEN during examine.
Also, initialize 'cortex_m->dcb_dhcsr' during examine.
[1] ARM DDI 0403E "ARM v7-M Architecture Reference Manual"
Change-Id: I5b0b23403634f7dfce38f104bba9f59c33eb3e99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5702
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Moritz Fischer <moritzf@google.com>
use handle_command_parse_bool within dap_ti_be_32_quirks_command to make
it shorter and simpler.
Change-Id: Ice179cc477933b27e27235dc2ade23fe655e233d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5708
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
avoid the usage of ERROR_COMMAND_SYNTAX_ERROR when
ERROR_COMMAND_ARGUMENT_INVALID is more adequate.
Change-Id: Ic9aaedb93fedd45efee1b39f8ea20185f01af2da
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5654
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The jim library exports all the data types through typedef, so
there is no need to use the internal struct types.
Fix the few remaining inconsistencies in the code.
Change-Id: Id4ae0083563ea7a371833374e7b39f17158f66a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5662
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Previously the adapter speed settings were hard-coded to
connect with low speed then switch over to high speed
regardless what was mentioned in the cfg files. Now the
stm8 target intercept adapter speed settings and configure
the stm8 control registers accordingly.
Change-Id: I7419514e5214e4b43b9d51253cf5b7f04a233533
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
SWIM is implemented by (ab)using the HLA API. This was acceptable
when OpenOCD code did not provided a clear separation between
transports and related APIs. Still today SWIM in OpenOCD is only
supported by STLink, so the decision to re-use the HLA API was the
simpler way to implement it.
After commit efd1d64222 ("adapter: switch from struct
jtag_interface to adapter_driver") the transports API are better
split and SWIM can be implemented as a separate set of API. This
would open the possibility to extend OpenOCD for other adapters
that provide SWIM, e.g. versaloon, or through SPI emulation [1].
Introduce a new set of files swim.[ch] to handle the SWIM API.
Beside the API that almost match the transport low-level data
communication (system_reset, read_mem, write_mem), add a further
API reconnect. Today, inside HLA STLink code, the reconnect is
implemented by hacking the HLA API state(). Please notice that
due to this hack the return type is incorrect; stlink_usb_state()
returns ERROR_OK in SWIM mode, while its return type is enum
target_state. Ignore the type mismatch and still call the HLA API
state in the new SWIM API reconnect. Further commit will fix it.
[1] http://kuku.eu.org/?projects/stm8spi/stm8spi
Change-Id: I52018e1e2200cbd41af8e5031f7b35dc761b61d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5528
Tested-by: jenkins
* WIP making semihosting work with -rtos hwthread.
Change-Id: Icb46f3eeedc1391e8fdc73c3ad8036f20267eb2e
* More WIP.
Change-Id: I670a6e1ba2a13a6ef2ae303a99559a16fdd1bbfb
* Fix halting due to a trigger.
Change-Id: Ie7caa8dde9518bcd5440e34cf31ed0d30ebf29ad
* Fix multicore semihosting without halt groups.
Change-Id: I53587e5234308ed2cc30a7132c86e4c94eb176c4
* WIP
Change-Id: I40630543b08d8b533726cb3f63aa60a62be8ef40
* Fix single core semihosting.
This was the last bug!
Change-Id: I593abac027fa9707f48b7f58163d7089574a0e28
* Fix whitespace.
Change-Id: I285c152970b87864c63803fae61312e5b79dfe6d
Commit da41bce3ae ("target/arc: introduce breakpoint
functionality") introduces a mismatch between the format string
and one int constant.
Change the format string to match the int constant.
Change-Id: I0d59552205551b90e165c0a2e3fef247ad0c7701
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: da41bce3ae ("target/arc: introduce breakpoint functionality")
Reviewed-on: http://openocd.zylin.com/5655
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Expression like (0xffff << 16) evaluate to type int, which is not able
to hold that value, producing a warning when compiling with
-fsanitize=undefined. This patch makes most of the cortex_m constants
unsigned using the BIT() macro or appending "ul" when possible to fix
the undefined behavior warning.
Signed-off-by: iosabi <iosabi@protonmail.com>
Change-Id: I7af194305ef612d7a32e74eaf9f11dd85fa87f32
Reviewed-on: http://openocd.zylin.com/5583
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types OPEN_BRACE -f {} \;
Change-Id: I6d1356ed11e2699525f384efb7556bc2efdc299f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5628
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The coding style is quite permissive allowing 120 chars per line,
but abuses are still present.
Fix them, wrapping the lines.
Change-Id: I94d66b651d759a60ec35f7ba115c43933e70ed69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5626
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The statement "else" should not be on a new line when follows a
close brace '}'. Fix it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ELSE_AFTER_BRACE -f {} \;
Change-Id: I8af247ec3f75a69713d7cb1e73881254d16c189e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5623
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
With this patch we introduce set/unset breakpoints
routines and add/remove bp handlers.
Currently soft breakpoints are only supported.
Changes since v1:
* Change if-statement in arc_remove_breakpoint
* Squash changes from http://openocd.zylin.com/#/c/5641/
in this commit to fix build.
Change-Id: Ib10ccdb02fd1606e4f407f012b1bee106a8ffccd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5641
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This commit introduces helper instruction read/write functions
for further bp functionality.
Change-Id: I619fbe2870ef6365c29ed1618bb83b6f7eb84690
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5640
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This fixes a bug where we read PC and marked it cached without actually
updating the cached value. The DPC value was correctly marked as valid
and updated.
Change-Id: Id6d3e94a96b981688b06f7f4a998019f2c02f6f5
Introduce a variable 'size' and reduce the number of dereferencing
*reg_list_size by using the variable.
Change-Id: I3bdf1485a4ed8e34435e8acb3efd0df8d802508c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Empty lines at end of text files are useless.
Remove them.
Change-Id: Ibac9b36682d58f81e34ca2b51e6260e7d472fb0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5172
Tested-by: jenkins
The CPU target name is added to the HALT status message so the user
can see which target halted at the designated program counter.
Tested on an Ampere eMAG8180 and Quicksilver silicon
Change-Id: I51e6f21296c85a822df28c5b7c4068e8ff66f29e
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5571
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Cache accesses through riscv_[sg]et_register.
This helps a lot with the address translation code, which checks satp
over and over again. Now satp is only read once per halt. It should also
help in a few other cases (but I don't have a good test setup to really
measure the impact).
Change-Id: I90392cc60d2145a70cf6c003d6a956dc9f3c0cc4
* Fix whitespace.
Change-Id: I05c5342d8a461cd8c618a3f60296925e9e84643f
* Don't read registers that we know don't exist.
Change-Id: Ie5c6226b3d4ecb6cf8f0d8954a52fda88e6e5bdd
Introduce a new ERROR_TARGET_ALGO_EXIT as currently used
ERROR_TARGET_TIMEOUT should be reserved for the timeout only.
Do not load PC directly from CPU HW as the register value
has already been cached.
Change-Id: I0d3630da41fd021676789dc12b52545cc0432ba8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5329
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
BUILD_TARGET64 creates a larger test matrix and mostly gates the
building of the aarch64/armv8 target, make that unconditional, which
would help fixing any issues with 64-bit address types anyway.
Rebased by Antonio Borneo after commit 1fbe8450a9 ("mips: Add
MIPS64 support")
Change-Id: I219f62b744d540d9dde9a42e6b63fd7d91df3dbb
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5240
Tested-by: jenkins
In arc_poll() function we handle the cases, when jtag indicates, that
processor is halted, but target->state is not TARGET_HALTED.
In case, when processor was halted and target->state was TARGET_RUNNING,
we should save context. At the same time if target->state was TARGET_RESET
we do not need to save context.
Changes: 16.04:
Fix - Move setting target->state = TARGET_HALT after
"target->state == TARGET_RUNNIG" check, otherwise
this check makes no sense
Change-Id: I92ab6ec71cf58273bb8401d14a562035de3deab4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5524
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
If we return failure, then the caller will think something's wrong. But
it could very well be that the hardware doesn't have SATP, in which case
we should just report that the MMU is disabled.
This fixes a bug where flashing wasn't using the target algorithm
because allocating a work area failed.
Change-Id: I16e8e660036d3f8584c0b17e842c4ec8961a8410
The command "soft_reset_halt" is deprecated since mid 2013 with
the commit 146dfe3295 ("cortex_m: deprecate soft_reset_halt").
Nevertheless it is still extremely useful with multicore chips
where it allows to reset only one of the cores, option not
available through asserting the chip-wide srst.
It also get useful to handle the reset on some problematic chip,
as in http://openocd.zylin.com/5489
Replace the warning about deprecation with a more light debug
message.
Change-Id: I52de6359475ba31014ae77e596a87fe88b252177
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5514
Tested-by: jenkins
Reviewed-by: Edward Fewell <efewell@ti.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The tcl script src/target/startup.tcl has already the proper
centralized support to wait for all targets to halt after the
command "reset halt". The extra wait in cortex_a_deassert_reset()
is not required.
This extra wait is also an issue for multi-core support, because
waiting for one core to halt can delay the halt request to the
other cores.
Replace the indirect call to cortex_a_halt(), that embeds the wait
for halt, with a low-level halt sequence.
The on-going work on the reset framework is compatible with this
change; in fact it keeps in startup.tcl the wait for targets to
halt, even if current code proposal for cortex_a simply removes
the function cortex_a_deassert_reset().
Change-Id: Ic661c3791a29ba7d520e31f85a61f939a646feb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5472
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Events TARGET_EVENT_STEP_START and TARGET_EVENT_STEP_END
have been added - analogous to already existing events
TARGET_EVENT_RESUME_*.
This is an example of a concrete use case where having
these events is important:
In RISC-V processors without Debug Program Buffer, OpenOCD
cannot execute fence/fence.i when resuming or single-
stepping. With these events implemented, the user can
instead provide custom operations to achieve that same
effect prior to resuming the processor.
Change-Id: I786348ff08940759d99b0f24e9e0ed5a44581094
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5551
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
when openocd fails to read armv8 register, the user is not informed
which register has caused the error.
for example, in AArch32 state ESR_EL3 read/write is not supported,
thus armv8_dpm_read_current_registers is always failing without mentioning
which register has caused the error.
Change-Id: I24c5abbda9fac24fb77a01777ed15261aeaaf800
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5516
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add more argument check for "add-reg" command.
Changes since first revision:
-Removed arguments limitation(50 maximum) for "arc_set_reg_exists".
Changes:
25.03:
Removed inconsistency in "add-reg" function. Actually
"-type" option is optional and if it is not set,
register type is "int".
Change-Id: Ia21e6baf4fbda162f7811cd0fe305fc86ddafcfd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5523
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Instead of exiting during examine(), spit out a warning, and don't
expose the vector data registers. We do provide access to the vector
CSRs, because maybe they do work? It's just that we have no idea what
the size of the data registers is.
Change-Id: I6e9ffeb242e2e22fc62cb1b50782c2efb4ace0bd
The memory leak can be reproduced by using an arbitrary RTOS
and valgrind:
$ valgrind --leak-check=full --show-leak-kinds=all
[...]
==9656== 224 (80 direct, 144 indirect) bytes in 1 blocks are definitely lost in loss record 3 of 3
==9656== at 0x483CD99: calloc (in /usr/lib/x86_64-linux-gnu/valgrind/vgpreload_memcheck-amd64-linux.so)
==9656== by 0x1C541A: os_alloc (rtos.c:79)
==9656== by 0x1C569E: os_alloc_create (rtos.c:111)
==9656== by 0x1C569E: rtos_create (rtos.c:153)
==9656== by 0x1AE332: target_configure (target.c:4899)
==9656== by 0x1AF228: jim_target_configure (target.c:4952)
==9656== by 0x1C9EF9: command_unknown (command.c:1066)
==9656== by 0x313284: JimInvokeCommand (jim.c:10364)
==9656== by 0x313FB6: Jim_EvalObj (jim.c:10814)
==9656== by 0x3154A3: Jim_EvalFile (jim.c:11207)
==9656== by 0x316015: Jim_SourceCoreCommand (jim.c:15230)
==9656== by 0x313284: JimInvokeCommand (jim.c:10364)
==9656== by 0x313B8B: JimEvalObjList (jim.c:10605)
[...]
Change-Id: I2cd41a154fb8570842601ff4e3e76502f5908f49
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5479
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Hypervisor mode is present only if the optional virtualization
extensions are available. Moreover, virtualization extensions
require that also security extensions are implemented.
Add the required infrastructure for the shadowed registers in
hypervisor mode.
Make monitor shadowed registers visible in hypervisor mode too.
Make hypervisor shadowed registers visible in hypervisor mode
only.
Check during cortex_a examine if virtualization extensions are
present and then conditionally enable the visibility of both
hypervisor and monitor modes shadowed registers.
Change-Id: I81dbb1ee8baf4c9f1a2226b77c10c8a2a7b34871
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5261
Tested-by: jenkins
Accordingly to ARM DDI 0406C at B1.5, the security extensions for
armv7a are optional extensions and can be detected by reading
ID_PFR1.
The monitor mode is part of the security extensions and the shadow
registers "sp_mon", "lr_mon" and "spsr_mon" are only present with
the security extensions.
Read the register ID_PFR1 during cortex_a examine, determine if
security extension is present and then conditionally enable the
visibility of the monitor mode shadow registers.
Change-Id: Ib4834698659046566f6dc5cd35b44de122dc02e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5259
Tested-by: jenkins
The fields core_type and core_mode use the same enum arm_mode
but encode different information, making the code less immediate
to read.
Use a different enum arm_core_type for the field core_type.
The code behavior is not changed.
Change-Id: I60f2095ea6801dfe22f6da81ec295ca71ef90466
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5258
Tested-by: jenkins
Commit 2efb1f14f6 ("Add GDB remote target description support
for ARM4") inserts two additional registers "sp" and "lr" in the
table arm_core_regs[], thus shifting by two the position of the
last three registers already present
"sp_mon" moved from index 37 to 39
"lr_mon" moved from index 38 to 40
"spsr_mon" moved from index 39 to 41
Part of the code is updated (e.g. enum defining ARM_SPSR_MON and
array arm_mon_indices[]), but it's missing the update of mapping
in armv4_5_core_reg_map[].
Fix armv4_5_core_reg_map[].
Change-Id: I0bdf766183392eb738206b876cd9559aacc29fa0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 2efb1f14f6 ("Add GDB remote target description support for ARM4")
Reviewed-on: http://openocd.zylin.com/5257
Tested-by: jenkins
The jimtcl commit 41c5ff1809f5 ("jim.c: Fix Object leak in zlib
support") https://repo.or.cz/jimtcl.git/commit/41c5ff1809f5
makes Jim_SetResultFormatted() freeing the parameters that have
zero refcount.
OpenOCD commit 559d08c19e ("jim tests: use installed") adds the
only code instance in OpenOCD that first passes a zero refcount
object to Jim_SetResultFormatted() and then frees it.
By switching jimtcl version to 0.78 or newer this causes a crash
of OpenOCD.
To trigger the crash in a telnet session, check that the current
target is running and type:
[target current] arp_waitstate halted 1
Remove the call to Jim_FreeNewObj() after the call to
Jim_SetResultFormatted().
Change-Id: I5f5a8bca96a0e8466ff7b789fe578ea9785fa550
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5453
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
note: this works only when the PE is in AArch64 state
Change-Id: Id6a336ca7d201df72bd1aaaeccce4185473fc1bd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5474
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
A common problem with target configurations appears to be broken
debug base address configuration. ARM DDI0406C.d specifies in App. D,
1.4.1, that bit 31 of the debug base address serves as identification
of an external debugger, as opposed to an internal access to memory
mapped debug registers by the CPU. External accesses are treated
as privileged and require no debug authentification via the lock
access register.
Sometimes the base address of a debug component is wrong even
in the targets' ROM table. In this case, the correct base address
must be specified using the -dbgbase argument when creating the
target.
This patch adds a warning when bit 31 of the debug base address
is not set, as a hint to the user.
Change-Id: I9c41d85a138123c657ef655e3436a2aa39249dcc
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/5105
Tested-by: jenkins
Reviewed-by: Tommy Vestermark <tov@vestermark.dk>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As stated in ARM v8-A Architecture Reference Manual (ARM DDI 0487E.a)
in Chapter H4.3 DCC and ITR access modes:
Writes to EDITR trigger the instruction to be executed if the PE
is in Debug state:
- If the PE is in AArch64 state, this is an A64 instruction.
- If the PE is in AArch32 state, this is a T32 instruction
But in armv8_opcodes specifically in t32_opcodes we were using some
A32 instructions for HLT, LDRx and STRx opcodes.
Using the correct LDRx and STRx opcodes, fixes 16 and 8 bits memory access
when the PE is in AArch32 state.
Change-Id: Ib1acbdd4966297e7b069569bcb8deea3c3993615
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5346
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Before this patch aarch64_set_breakpoint was using either A64, or A32
HLT opcode by relying on armv8_opcode helper.
This behaviors ignores the fact that in AArch32 state the core could
execute Thumb-2 instructions, and gdb could request to insert a soft
bkpt in a Thumb-2 code chunk.
In this change, we check the core_state and bkpt length to know the
correct opcode to use.
Note: based on https://sourceware.org/gdb/current/onlinedocs/gdb/ARM-Breakpoint-Kinds.html
if bkpt length/kind == 3, we should replace a 32-bit Thumb-2 opcode,
then we use twice the 16 bits Thumb-2 bkpt opcode and we fix-up the
length to 4 bytes, in order to set correctly the bpkt.
Change-Id: I8f3551124412c61d155eae87761767e9937f917d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5355
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
when using step command from gdb the step happens without any issue,
but aarch64_step call explicitly aarch64_poll which consumes the
status change to HALTED, so it does not inform gdb that the step has
finished.
by removing this call, all is back to normal and openocd could inform gdb
that the step has finished.
Change-Id: I9366aecd20f7d52259b050b8653189b67d9299d0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5354
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the same semihosting handlers chain is declared twice:
1. in src/target/armv4_5.c
2. in src/target/riscv/riscv.c
to make it simpler we moved the declaration into
'src/target/semihosting_common.c' under semihosting_common_handlers[].
then we used this into both of armv4_5.c and riscv.c
Change-Id: If813b3fd5eb2476658f1308f741c4e805141f617
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5473
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Writing bits to an uninitialized buffer generated false warnings.
Zero buffers before setting them by buf_set_u32|64()
(do it only if bit-by-bit copy loop is used,
zeroed buffer is not necessary if a fast path write is used)
Change-Id: I2f7f8ddb45b0cbd08d3e249534fc51f4b5cc6694
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5383
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch is an initial bump of ARC-specific code
which implements the ARCv2 target(EMSK board) initializing
routine and some basic remote connection/load/continue
functionality.
Changes:
03.12.2019:
-Add return value checks.
-Using static code analizer next fixes were made:
Mem leak in functions:
arc_jtag_read_memory,arc_jtag_read_memory,
arc_jtag_write_registers, arc_jtag_read_registers,
jim_arc_add_reg_type_flags, jim_arc_add_reg_type_struct,
arc_build_reg_cache, arc_mem_read.
Dead code in "arc_mem_read";
In arc_save_context, arc_restore_context correct arguments
in"memset" calls.
In "build_bcr_reg_cache", "arc_build_reg_cache" check
if list is not empty.
29.12.2019
-Moved code from arc_v2.c to arc.c
-Added checks of the result of calloc/malloc calls
-Reworked arc_cmd.c: replaced spagetty code with functions
-Moved to one style in if statements - to "if(!bla)"
-Changed Licence headers
22.01.2020
-Removed unused variables in arc_common
-Renamed register operation functions
-Introduced arc_deinit_target function
-Fixed interrupt handling in halt/resume:
* add irq_state field in arc_common
* fix irq enable/disable calls ( now STATUS32 register is used)
-Switched from buf_set(get)_us32() usage to target_buffer_set(get)_u32()
-Made some cleanup
30.01.2020
-Removed redundant arc_register struct, moved target link to arc_reg_desc
-Introduced link to BCR reg cache in arc_common for freeing memory.
-Now arc_deinit_target frees all arc-related allocated memory.
Valgrind shows no memory leaks.
-Inroduced arch description in arc.c
01.02.2020
-Remove small memory allocations in arc_init_reg. Instead created reg_value
and feature fields in arc_reg_desc.
-Add return value for arc_init_reg() func.
-Replaced some integer constants(61,62,63) with defines.
-Removed redundant conversions in arc_reg_get_field().
-Moved iccm/dccm configuration code from arc_configure()
to separate functions.
19.02.2020
-Change sizeof(struct) to sizeof(*ptr) in allocations
-Changed if/while(ptr != NULL) to if/while(ptr)
-Removed unused variables from struct arc_jtag
-Add additional structs to arc_reg_data_type
to reduce amount of memory allocations calls
and simplifying memory freeing.
-Add helper arc_reg_bitfield_t struct which includes
reg_data_type_bitfield object and char[] name. Reduces
memory allocations calls.
-Add limit for reg_type/reg_type_field names(20 symbols).
-Add in jim_arc_add_reg_type*() functions additional
argnument checks(amount of field/name size).
-In jim_arc_add_reg_type*() reduced amount of memory allocations.
-Cleanup of jim_arc_add_reg_type*() functions.
-For commands update ".usage" fields according docopt.
-Cleanup in arc_jtag.c
-Renamed functions which require jtag_exeutre_queue() to arc_jtag_enque_*()
-Add arc_jtag_enque_register_rw() function, which r/w to jtag ir/dr regs
during regiter r/w.
24.02:
-Change include guards in arc* files according coding style
-Remove _t suffix in struct arc_reg_bitfield_t
-Some cleanup
Change-Id: I6ab0e82b12e6ddb683c9d13dfb7dd6f49a30cb9f
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5332
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
Deassert the reset only if connect under reset is not required;
otherwise, assert the reset.
This fix aligns the behavior of connect under reset in dapdirect
with the behavior in jtag and swd.
Change-Id: I937ef4320b44e51ef6cb0e349e12348dbfbe4abb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5415
Tested-by: jenkins
Commit 3799eded67 ("target/aarch64: add support for
multi-architecture gdb") passes the constant string "aarch64" as
architecture to gdb. This is not working if the core is running
in 32 bits mode; gdb reports:
Truncated register 8 in remote 'g' packet
then closes the connection with OpenOCD.
Make the architecture string dependant from the current state of
the core.
Change-Id: I16e1614ea02ba29bf87f450b3dfe25c83c9a3612
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5234
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types UNNECESSARY_PARENTHESES -f {} \;
then fixed manually.
Change-Id: Ia2d9a0953d9b89fc87dc1195aa05c7f63c068c48
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5196
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro NDS32_COMMON_MAGIC was cast-ed to int to avoid compile
time error for comparison type mismatch while comparing it with
the field common_magic.
This is incorrect because the macro value is a 32 bit unsigned
value; better changing the type of the field common_magic to keep
the unsigned value.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPECAST_INT_CONSTANT -f {} \;
Change-Id: Ib5924b6cecdffe70ab5c78d3b30a9c8e4deb7c7b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5193
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* WIP
Change-Id: I0264a73b7f7d2ce89cc0b80692dbf81d9cdcc2fd
* Reading v* registers appears to work.
Can't really test it though, because gdb doesn't print them right.
Change-Id: I8d66339371c564a493d32f15c3d114b738a455c5
* Total hack to communicate registers to gdb.
Change-Id: Id06c819675f2a5bcaf751e322d95a7d71c633765
* Implement writing vector registers.
Fixed reading vector registers.
Change-Id: I8f06aa5ee5020b3213a4f68644c205c9d6b9d214
* Show gdb the actual size of the vector registers.
This length may be different per hart.
Change-Id: I92e95383da82ee7a5c995822a53d51b1ea933493
* Remove outdated todo comment.
Change-Id: Ic9158b002858f0d15a6452773b095aa5f4501128
* Removed TODO comment.
Filed #449 to track this.
Change-Id: I5277b19e545df2024f34cda39158ddf7d0d89d47
* Nicely handle some errors reading/writing V regs.
Change-Id: Ia7bb63a5f9433d9f7b46496b2c0994864cfc4a09
Since commit 7f260f5009 native OpenOCD
command handlers should not directly use Jim_SetResult functions.
The Tcl result of a native command is built as concatenation of
command_print() strings and Jim_SetResult() is called after return
of the command handler.
Replace "wrong number of args" error messages (now not delivered to user)
by simply return ERROR_COMMAND_SYNTAX_ERROR
Change-Id: I40c1374a13859cefbdef68e0f1c13ab93538bd50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5363
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Fixed only 2 error returns discovered by clang static analyzer.
There are obviously many more missing error tests in avr32_jtag.c
These was not fixed to keep this change minimal.
Not tested with hw.
Change-Id: I6c79f6248db774990ddb42c0dacdb621651ed69e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5378
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Discoverd by clang static analyzer.
While on it remove useless type casts from arm946e_read_cp15() parameter.
Change-Id: I549e19685b431400243800ee0f7d1bbe6cdb14b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5376
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The `value` variable is passed into `target_fill_mem` as its
second-to-last parameter. That parameter is of type `uint64_t`. It is
appropriate to parse the value as that type, since otherwise a target
with a 32-bit address space but 64-bit data write capabilities would not
be able to exercise those capabilities.
Change-Id: Ib336d47d42c27cd2b5ba1206b04e8f740f167dba
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5219
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some high level adapters, like STLINK-V3 and new firmware for
ST-Link/V2, provide API to directly access the DAP registers
hiding the details of the physical transport JTAG or SWD.
OpenOCD has already the intermediate API in struct dap_ops that
are suitable for such adapters, but are not exposed to the
adapter drivers.
Add in struct adapter_driver two independent struct dap_ops for
the cases of physical JTAG and SWD transport.
Add new transport names "dapdirect_jtag" and "dapdirect_swd", to
be used by the drivers that provide one or both DAP API.
Add the necessarily glue in target/adi_v5_dapdirect.c
Change-Id: I2bb8e3a80fba750f2c218d877cfa5888428e3c28
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To reorganize the adapters code, introduce an adapter_driver
struct that contains all the adapter generic part, while
keeping in two separate struct the specific API jtag_ops and
swd_ops.
Move the allocation of *adapter_driver from the JTAG-specific
file core.c to the more adapter-specific file adapter.c
While splitting the old jtag_interface for every driver, put
the fields in the same order as in the struct declaration so
we keep a consistent code across all the drivers.
While other transport specific API could/would be added as
separate ops, nothing is done here for HLA.
Change-Id: I2d60f97ac514c0dd2d93a6ec9be66fd9d388dad5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4900
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
HLA uses its own internal driver's API to control the adapter's
system reset, but at the same time it calls jtag_add_reset() to
avoid breaking the internal logic of OpenOCD. This implicitly
forces HLA to rely on jtag queue mechanism, even if HLA has no
link with JTAG state machine. It requires HLA to implement an
empty execute_queue() to comply with the JTAG queue.
Modify the HLA framework and the HLA targets to use the new
adapter API for system_reset and decouple HLA from JTAG queue.
Rename the HLA static functions adapter_assert_reset() and
adapter_deassert_reset() to avoid overlap with the global
functions with same name.
While there, fix a minor typo in a comment s/incase/in case/.
Do not remove from HLA the JTAG specific API execute_queue(),
even if not required anymore, because OpenOCD code still has
calls to jtag_execute_queue() in case of non JTAG transport.
Change-Id: I0e65e3e557bd665bd3d3aeaa84ea609b55a05e48
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4896
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The transport SWD uses the JTAG queue to assert/deassert the
system reset srst. This is the major inconsistency that has to be
removed to properly split JTAG and SWD.
Introduce a new driver API, reset(), to controls both the signals
trst and srst in the driver, skipping the JTAG queue. Put the new
API in struct jtag_interface, even if in this patch it's used for
SWD only; the goal is to get it reused by the other transports.
Add the implementation of the API in all the drivers that
implement SWD. Such implementation is almost the same of the old
code in JTAG queue.
Create a wrapper adapter_system_reset() to use the new API and
remove the SWD specific swd_add_reset(). In the wrapper replace
jtag_add_sleep() with jtag_sleep(), because the former uses the
JTAG queue too.
Rename the old jtag_add_reset() as legacy_jtag_add_reset() with
the target to remove it when all drivers would be ported to the
new reset API. Create a new jtag_add_reset() that calls the
legacy function for drivers still on the old reset API.
Use the new API also on JTAG transport for the drivers that can
support both SWD and JTAG.
For the moment, do not modify the implementation of JTAG-only
drivers, which will continue using the usual method. This should
be cleaned-up in future commits.
Change-Id: I32331c88313f6059b25e12c6bb0156aebc1c074f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Handle DMI busy in sba write.
If we encounter DMI busy on the NOP after a read, we'll never get the
value out because DMI busy is sticky. The read must be retried, but we
don't know whether it was ever issued. Since the read has side effects
(incrementing of the address) this retry must be handled at a higher
layer. So now dmi_op_timeout can be told to retry or not, and if retry
is disabled it'll return an error when busy.
Also actually properly do the retry in dmi_op_timeout(). Previously the
code would not reissue the command and end up returning a garbage value.
Change-Id: I3b52ebd51ebbbedd6e425676ac861b57fbe711b1
* Fix whitespace.
Change-Id: Icb76d964e681b22346368d224d1930c9342343f3
* Handle a few more DMI busy cases.
Change-Id: I8503a44e4bf935c0ebfff0d598fe4c322fda702a
* Explain when to use dmi_op_timeout(retry).
Change-Id: I1a5c6d76ac41a84472a8f79faecb2f48105191ff
* dmi_reset does not affect the current transaction.
That means the retry scheme we had been using works fine. This does
contain some minor tweaks, and now we pass my tests which hammer the DMI
busy case harder.
Change-Id: I13eee384dbba82bc5a5b1d387c75c547afe557b5
* Remove unnecessary changes to make the PR readable
Change-Id: I87079876e6965563cf590e3936b3595aeab8715d
* Move idle to end of line...
... because we go through run-test/idle after the scan.
Change-Id: I21a8cff22471f0b895d8cd8d25373dced9bf1ca9
* Remove unused code.
Change-Id: I07a7cdd2d64ca40a4fe181111a34cf55ff1928d1
The original OpenOCD code issued FENCE & FENCE.i twice for the current
hart (which is harmless, but takes time).
Avoiding this extra FENCE is a slight performance improvement. Per my rough
measurements, this improves performance of certain debugger actions
(single-stepping) by approx. 20% in single-hart systems.
The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().
Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h
Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
these commands have been introduced to ease the manipulation of CTI trough
script files, these commands are:
- $cti_name ack $event : to acknowledge a CTI event
- $cti_name channel $channel_number $operation: to perform an operation
on a specific channel, the possible operations are:
gate, ungate, set, clear and pulse
Change-Id: I35463867a3c85072f3776c3aeb1e5788953ec435
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5315
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* riscv: Fix bugs. Do not touch SATP if there is no MMU.
In some platform, there is no SATP register at all.
OpenOCD will report unexpected errors if SATP is unreadable.
So, use 'riscv_enable_virtual' to guard SATP access.
* riscv: fix format typo.
The SWO frequency auto-detection with J-Link adapters does not work
properly in the current implementation. This is because the trace layer
has only information about the highest possible SWO frequency supported
by the adapter. With that the trace layer calculates the SWO prescaler
which usually leads to a frequency deviation greater than what is
permitted by J-Link adapters.
Move the calculation of the SWO prescaler from the trace layer into the
trace configuration of the adapter to overcome this problem.
The adapter has the necessary information to choose a suitable SWO
frequency and calculate the corresponding prescaler that complies with
the maximum allowed frequency deviation.
Tested with:
- STM32L152RC Discovery Kit (ST-Link)
- EFM32GG-STK3700 (J-Link)
Change-Id: I38ff2b89d32f0a92c597989b590afe5c75cf4902
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3903
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
During code analysis and development, counting again and again the
lines to find the index of the register is a boring error-prone
brain-damaging activity.
Use the c99 syntax and add once forever the array designators to
specify the index values.
The code behavior is not changed.
Change-Id: I2c70f70794475679efb91a8dfadc00f50715bd3f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5256
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The GDB file-I/O remote protocol extension, used for implementing
the semihosting file I/O, requires the length of strings to
include the trailing zero character, as explicitly stated inside a
comment in GDB source code [1]:
/* 1. Parameter: Ptr to pathname / length incl. trailing zero. */
ARM specification for semihosting [2] requires the string length
to not include the trailing zero character, e.g. in SYS_OPEN
specifications:
"field 3: An integer that gives the length of the string
pointed to by field 1. The length does not include the
terminating null character that must be present."
The mismatch above requires OpenOCD to add "one" to the string
length before passing it to GDB. Such conversion is missing
either in the generic semihosting provider of the data, the
function semihosting_common(), and in the consumer of the data,
the gdb_server function gdb_fileio_reply().
The conversion is already implemented in the target specific
function nds32_get_gdb_fileio_info(), but it's not the preferred
place for such GDB specific requirement.
This issue affects the semihosting calls "open", "unlink",
"rename" and "system".
Remove the "+1" conversion from nds32_get_gdb_fileio_info().
Add the "+1" conversion in gdb_fileio_reply().
[1] http://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;f=gdb/remote-fileio.c;h=11c141e42c4d#l381
[2] "Semihosting for AArch32 and AArch64, Release 2.0"
https://static.docs.arm.com/100863/0200/semihosting.pdf
Change-Id: I35461bcb30f734fe2d51f7f0d418e3d04b4af506
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5322
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Abstract write size (aarsize) to shall always match the real
size of the register. This is because abstract write of smaller size
than the register need not be supported per spec (pg. 13 of RISC-V
External Debug Support ver. 0.13.2).
Fix memory access on 64-bit targets with no progbuf and sba that
supports 32-bit accesses but not 64-bit accesses. Bug was introduced in #419.
This fixes https://github.com/riscv/riscv-tests/issues/217.
Change-Id: Ib5ddf9886b77e3d58fe1d891b560ad03d5a46da1
When allocating scratch memory within RISC-V target
(scratch_reserve()), take into account whether progbuf
is writable or not, as determined by examine_progbuf().
* fix for batch scans not honoring presence of BSCAN tunnel
* fix formatting to placate checkpatch
* replace DIM with ARRAY_SIZE
* Refactor code that adds a bscan tunneled scan.
* Move bscan tunnel context to the batch structure, and in array
form, one per scan
* adjust code that was inconsistent with project code formatting standards
* 64-bit progbuf memory reads work.
Change-Id: Ia3dbc0ee39a31ed0e5c38bbb3d9e089b2533f399
* 64-bit writes work.
Change-Id: Iae78711d715b6682817bb7cce366b0094bda8b23
* Let targets indicate number of supported data bits.
This is used by the default memory read/write functions when creating an
aligned block.
I'm adding this mainly to ensure I get coverage of the 64-bit progbuf
memory read/write code.
Change-Id: Ie5909fe537c9ec3360a8d2837f84be00a63de77b
* Make mingw32 happy.
Change-Id: Iade8c1fdfc72ccafc82f2f34923577032b668916
In preparation for supporting the ARM MCRR and MRRC commands which will
require using two 32-bit registers to read/write a 64-bit internal
register, extract the common logic to read/write from/to a register
to/from DCC and make that parameterized such that we can do this through
not just r0.
Change-Id: Iadb73f5cde8cf5961b5a18ddd198bf39d791e610
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Armv7a is able to read and write memory at un-aligned address, but
only when bit SCTLR.A (Alignment check enable) is zero and the
address belongs to a memory space with attribute "Normal" (see [1]
chapter A3.2.1 "Unaligned data access"). In all the other cases
the memory access will trigger an alignment fault data abort
exception.
Memory attributes are explained in [1] chapter A3.5 "Memory types
and attributes and the memory order model".
Disabling the MMU cause a change in memory attribute, as explained
in [1] chapter B3.2 "The effects of disabling MMUs on VMSA
behavior".
This can cause several issues. e.g. a SW breakpoint on un-aligned
4-byte Thumb instruction, set when MMU is on, can be impossible to
remove when MMU turns off.
While is possible to check all the possible conditions before an
un-aligned memory access, it's clearly more maintainable to skip
such complexity and only perform aligned accesses.
Check the alignment and eventually modify the data size before
calling the functions cortex_a_{read,write}_cpu_memory_slow().
Change the comment in the two functions above to comply with the
new behaviour.
[1] ARM DDI 0406C.d - "ARM Architecture Reference Manual, ARMv7-A
and ARMv7-R edition"
Change-Id: I57b4c11e7fa7e78aaaaee4406a5734b48db740ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5138
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Issue has been found when I tried to read 64 MiB QSPI flash bank.
Bank is memory mapped, default_flash_read() is used for 'flash read_bank'
command. OpenOCD consumed as much as 6.8 GiB of RAM during this
process. Investigation showed that this happens because JTAG queue
is not limited in any way. OpenOCD queues 16 millions of AP reads
allocating all corresponding data structures.
Most of this memory is allocated in:
cmd_queue_alloc (commands.c) - 4.2 GiB
dap_cmd_new (adi_v5_jtag.c) - 2.25GiB
This patch implements a pool of "struct dap_cmd" objects using
linked list. Objects are taken from a pool in "dap_cmd_new()" and
returned to the pool when they are not needed. Size of the pool
is limited to 64K of objects, JTAG queue is forcibly executed
when this limit is reached.
Checked with Valgrind and Clang analyzer - no new warnings.
Change-Id: I5aaaecce5ed71414f7965a2598f49742f6a6b2b5
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4948
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current code checks the count to determine whether to read bytes or
words. However it fails to consider whether the base address is suitably
aligned.
Instead use the target_read_buffer() function which is for exactly this
purpose and generates optimal accesses with natural alignment.
Change-Id: I32ab5417890ee2219902df1529bc220fe353b4c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3217
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Add riscv_batch_available_scans().
This function will query the number of available scans in a batch.
* Perform SBA writes with batch transactions for improved performance.
Using batch transactions avoids an unnecessary dmi read after every
dmi write, resulting in a significant performance improvement.
* Align algorithm stack to XLEN.
This fixes algorithm timeout on RV64 targets.
Also improve debug information in various places.
Change-Id: Id3121f9c6e753c6a7e14da511e4de0587a6f7b4d
* Compile 32-bit RISC-V algorithms for RV32E.
Change-Id: I33a698c0c6ba540de29fa0459242c72a67b0cbaa
* Remove debug code.
Change-Id: I37c966ce0f2d1fe68cd6ae0724d19ae95ebaf51b
* Dump start of gdb packets escaping non-printable.
Change-Id: Ie5f36b5c9041bfc0e5aa9543f0afe2c4810c2915
* Propagate flash programming errors.
Change-Id: I0c938ce7a1062bcc93426538cbc82424000f37b7
* Improve debug messaging.
Change-Id: I47ac3518f3b241986c677824864102936100adf6
* Add debug output to flash image.
This is helpful when you're debugging the flash algorithm itself, and a
nop when running it through OpenOCD.
Change-Id: Id44c6498c288872cc2cec79044116ac38198c572
* Make timeout depend on how much data is written.
Change-Id: I819efa04cd6f6bd6664afd5c53cc7a8a5c84f54e
* Fix issi erase commands.
This is required to flash HiFive Unleashed.
Change-Id: I33e4869d1d05ca8a1df6136bccf11afda61bfe10
* Fix running algorithm on multicore `-rtos riscv`.
The bug was that poll() might change the currently selected hart, and in
that case we'd access registers on that other hart after the algorithm
is finished.
Change-Id: I140431898285cf471b372139cef2378ab4879377
* Make fespi flash algorithm debugging optional.
Also add a scheme that allows you to see the stack trace of where a
failure occurred if debugging is enabled.
Change-Id: Ia9a3a9a941ceba0f8ff6b47da5a8643e5f84b252
Added "exist=true" field to the reg_list struct to make access to the
dsp563xx registers again possible. Without it defaults to exist=false
and all the reg related functions will return nothing.
Fixes regression from b5964191f0
Change-Id: I9c256346735b8d66919c4ba83f528a8afca46ff9
Signed-off-by: Han Hartgers <han.hartgers@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5239
Tested-by: jenkins
1. Add get_thread_reg() to rtos. It's used in rtos_get_gdb_reg() to read
the value of a single register, instead of reading all register values
by calling get_thread_reg_list().
2. Add set_reg() to rtos. gdb_server uses this to change a single
register value for a specific thread.
3. Add target_get_gdb_reg_list_noread() so it's possible for gdb to get
a list of registers without attempting to read their contents.
The clang static checker doesn't find any new problems with this change.
Change-Id: I77f792d1238cb015b91527ca8cb99593ccc8870e
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5114
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Clear cmderr by writing all ones.
This should have been part of #389.
Change-Id: Ie40e95fdd904af65c53d1f5de7c8464b27038ec0
* Don't update reg cache in register_write_direct().
This function explicitly bypasses any caches.
Change-Id: Ie3c9a1163e870f80c0ed75b74495079c527663e9
* Use only one hart to run algorithm.
Fixes a bug with `-rtos hwthread` where all harts would run when running
a flash/CRC algorithm, which would probably ruin flashing, and was
unexpectedly changing registers on other harts for the CRC algorithm.
Change-Id: Ia2f600624f4c8d4cab319861fef2c14722f08b53
* Adds support for RISCV Access Memory Abstract Commands
The Access Memory Abstract Command is one of the three optional
methods for reading and writing memory on a complient RISCV
debug module. The previous two options were already implemented
in OpenOCD.
Implementation Notes:
- aamvirtual is hard-coded to false until the design for accessing
virtual addresses is finalized.
- aamsizes corresponding to 8b, 16b, 32b, and 64b are supported.
128b support is postponed until it is required, as it will mean
changes to the read/write_abstract_arg() interface to pass 128b
values.
- aampostincrement is not used and hard-coded to false.
* Changes from review.
* Additional lint fixes and a typo from last commit.
* Fixing a clang error.
* Fixes a last-minute change that broke writes with width > 8b.
* Removing memcpy after adding read_from_buf().
* add opcode for csrrsi and csrrci
* enable MMU while reading/writing memory using progbuf
* fix style issues
* keep old behavior for progbufsize<4, perform r/w/csr only when necessary
* do not pass progbufsize, only write mstatus if changed
* add config option to enable virtualization feature
* throw error if virt enabled but unavaliable, outsource modify_privilege
* support virtualization for read_memory_progbuf_one
gdb has developed a nasty habit of very often reading 30-some
half-words. This change speeds that up significantly.
Change-Id: Iab1b7575bec5c57051c6e630ae292dddf8fe6350
* Make resume order configurable.
This is a customer requirement. Using this option is discouraged.
Change-Id: I520ec19cc23d7837cb8576f69dadf2b922fa2628
* Fix style.
Change-Id: If8e515984c92ce8df52aa69e87abde023897409f
* Make mingw32-gcc happy.
Change-Id: I39852aedec293294b2b2638ab2cc45494fe77beb
* WIP, rewrite of flash algorithm.
Just put all the flashing logic into the algorithm, instead of using an
intermediate format. This should reduce total data written while
flashing by about 9%, and also makes the code much simpler.
Change-Id: I807e60c8ab4f9f376cceaecdbbd10a2326be1c79
* New algorithm works.
Speeds up Arty flashing another 9%.
wrote 2228224 bytes from file /media/sf_tnewsome/SiFive/arty_images/arty.E21TraceFPGAEvaluationConfig.mcs in 86.784538s (25.074 KiB/s)
verified 2192012 bytes in 6.693336s (319.816 KiB/s)
8.66user 13.03system 1:33.91elapsed 23%CPU (0avgtext+0avgdata 12272maxresident)k
Change-Id: Ie55c5250d667251be141cb32b144bbcf3713fce4
* Fix whitespace.
Change-Id: I338d518fa11a108efb530ffe75a2030619457a0b
* Don't reserve so much stack space.
Also properly check XLEN in riscv_wrapper.S.
Change-Id: Ifa0301f3ea80f648fb8a6d6b6c8bf39f386fe4a6
* In theory support RV32E.
Change-Id: Icfe2a40976ae3161f2324e5bb586915aa4c4c7ee
* In theory support RV32E.
At least very basic tests pass.
Change-Id: Ia42e28a3fa020b3e52c92109392c46d009330355
* Fix cut and paste bug.
Change-Id: Ibfea68b39d706f59a8c3aa8153bb4db9803958c6
* Add hacks to make RV32E work with gdb.
gdb currently requires all 32 GPRs to be present, even on RV32E targets.
Once gdb is fixed these hacks can be removed.
Change-Id: Idcde648de2ca1a3f5b31315aab35fac86580af2c
The command "soft_reset_halt" is deprecated since mid 2013 with
the commit 146dfe3295 ("cortex_m: deprecate soft_reset_halt").
Nevertheless it is still extremely useful with multicore chips
where it allows to reset only one of the cores, option not
available through asserting the chip-wide srst.
Without a better replacement of the command, it's worth fixing it.
Accordingly to ARM DDI 0403E.d, chapter C1.4.1 "Entering Debug
state on leaving reset state", to halt the core at reset both bits
DHCSR.C_DEBUGEN and DEMCR.VC_CORERESET must be set.
Current code only sets the latter bit, relying on having C_DEBUGEN
already set through other commands, e.g. "halt". This prevents the
command "soft_reset_halt" to work if issued as very first command.
Set the bit C_DEBUGEN in command "soft_reset_halt".
Change-Id: I66bfd6a0da1fca5049dea037b4d258cf6f842966
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4987
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* Cache program buffer writes.
Speeds up flash program by 3%, flash verify by 2%.
Change-Id: I19f8f44f560a1111fa8f4e4fc04ce6de3c94999a
* Remove nop from batch reads.
program @ 22.123 KiB/s, verify @ 47.654 KiB/s (up from program @ 20.287
KiB/s, verify @ 23.148 KiB/s originally).
Change-Id: I7ee19d967b1080336b0088d20e1fc30828afd935
* Use "algorithm" to compute CRC on RISC-V targets.
Use the C compiler to generate the algorithm code. It's better at
assembly than I am. We need separate RV32 and RV64 binaries to handle
shift instructions. I used the code from gdb (libiberty really) because
it returns the correct result. I'm not sure if the table is worth it
since we do have to save/download/restore more bytes now.
riscv_run_algorithm() now properly saves and reads back all registers
used for parameters. It also doesn't check final_pc if exit_point is 0.
Using gdb means I don't know the exact address where the code will end.
Small target.[ch] change to be able to run algorithms at 64-bit
addresses.
Flashing an arty board now:
```
wrote 2228224 bytes from file /media/sf_tnewsome/SiFive/arty_images/arty.E21TraceFPGAEvaluationConfig.mcs in 105.589180s (20.608 KiB/s)
verified 2192012 bytes in 7.037476s (304.177 KiB/s)
9.87user 16.16system 1:53.16elapsed 23%CPU (0avgtext+0avgdata 24768maxresident)k
```
Change-Id: I6696bd4cda7c89ac5ccd21b2ff3aa1663d7d7190
* Clean up formatting.
Change-Id: I7f2d792a2b9432a04209272abb00d8136ee01025
The AHB5-AP is implemented in Cortex-M23/33 based devices.
Change-Id: I505954a2e2c6462ce0aa96eba1d55b016c5028b9
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5232
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
This access port type comes with the AMBA 5 protocol specification,
see 'C1.3 AP' in ARM IHI 0031D.
Change-Id: I3c4f0a69230daaf4f5f979de6213fe3c025a089a
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
This patch adds ARMv8-M CPUs detection logic in ARMv7m target specific code.
Also adds a slightly different watchpoint manipulation logic for ARMv8-M.
This is based on ARMv8-M architecture reference manual.
Tested on ARM Musca A board.
Change-Id: I0652560954ef02c378a7067fab586edf39d3e9cc
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4997
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I1b917a4c1205115c4e0315373d81a9305e931258
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4944
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Replace jtag specific API jtag_add_reset() with transport
independent API adapter_{de}assert_reset().
Change-Id: I32c43e2e47366363521fa3f387de9e2fb1c20852
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4943
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of target's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition, thus dumping the
call-trace. The execution is not stopped because the error is not
further propagated, but the error message is annoying and
misleading.
It can be tested running
openocd -f ./test.cfg
using the following script "test.cfg". You can replace the board
file in line 1, to use a board available in your lab:
1 source [find board/st_nucleo_f4.cfg]
2 [target current] configure -event reset-start {}
3 [target current] configure -event reset-end {return}
4 init
5 proc a {} {[target current] invoke-event reset-start}
6 proc b {} {[target current] invoke-event reset-end}
7 proc c {} {a;b;echo "arrived at the end"}
8 c
9 shutdown
The execution produces:
./test.cfg:7: Error:
in procedure 'c' called at file "./test.cfg", line 8
in procedure 'b' called at file "./test.cfg", line 7
arrived at the end
that shows the call-trace but does not halt the execution.
The developer can avoid using the "return" command in the event
body by defining a TCL procedure that implements the handler and
that contains the "return" command, reducing the handler body to
a simple call to the procedure above. But this approach is either
not documented nor always intuitive while writing the handler,
causing waste of time to look for the false error.
Modify target_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I2b860bab7233c6ed13ee4098e348d7533e1c4626
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4974
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit 877cec20dc
("command: check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The command '$_TARGET configure -xxx' was therefore applicable on running
OpenOCD to change the target configuration. It is handy e.g. for changing
an event handler or changes of the work area.
Change 'configure' command .mode to COMMAND_ANY to make it possible again.
The only parameter which cannot be re-configured after init is -gdb-port.
Test the command mode and refuse setting of gdb port after init.
Change-Id: I88493ac10a46647dc52a88fbc9f8ce6b5ba3bcd0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5214
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
since b5964191f0, all XScale-specific registers were missing, breaking
config scripts.
Change-Id: Ia56f3ca17500ba54bd08f417e9a5aaaa8a1be8c4
Signed-off-by: Michael Schwingen <spam-openocd@discworld.dascon.de>
Reviewed-on: http://openocd.zylin.com/5136
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro TARGET_ADDR_FMT, defined in helper/types.h, already
includes the prefix "0x" in front of the hexadecimal number,
being defined as:
#define TARGET_ADDR_FMT "0x%8.8" TARGET_PRIxADDR
An additional "0x" is present in mem_ap; it prints debug messages
with a double "0x" before the address:
Debug: 2921 34180 mem_ap.c:153 mem_ap_write_memory():
Writing memory at physical address 0x0x5000000c; size 4;
count 1
Remove the incorrect hexadecimal prefix.
Change-Id: I38f19ed2a2f542bd5df53e947a2604f1cbe80e08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5222
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The ARMv7-A architecture supports super sections which allows mapping
physical addresses up to 40-bit into a 32-bit virtual address using the
short descriptor format (see ARM DDI 0406C.c section B4.1.112 for
details).
Change-Id: I8e64d0e93e36ae7a7da7b7bf2a8342856bb044f1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5212
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
In preparation for adding super section decoding, do not restrict
armv7a_mmu_translate_va_pa() to 32-bit virtual addresses since ARMv7-A
processors with VMSA extensions (including LPAE) can issue wider
physical addresses. Update casting to uint32_t where necessary.
Change-Id: Id1c3d0d5ac324cbdc334259d9ea75fe4981671a1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5211
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This function is not used anywhere in the tree, remove it, such that we
only have a single function moving forward that might need to deal with
short vs. long format specifics.
Change-Id: I80e81cd7eba1e028d1afaeaedb675b46c0ca6fa1
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Check earlier that the read of the PAR register was successful instead
of starting the decoding and then checking for an error reading that
register.
Change-Id: Id96c2b2f76d2d1c745fcfa55ad4c1e6db92106f9
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* Inverted Frame to Pseudo Tap for Simpler Hardware to Decode
Given the variable supported message length , a prefix decoding approach is significantly simpler for a pseudo tap architecture with a shift reg of len = max len of packet. This prefix coding packet also makes the message len field redundant , as that is implict in ir_len and the ir selected.
* style patch
* non-conflict with original
* style patch
* style patch
* requested changes
* style-patch
armv7m_get_core_reg() calls arm->read_core_reg()
arm->read_core_reg() expects the register number as an index
to core reglist, not an ARMv7M specific register code.
Use reg->number instead of armv7m_reg->num.
The change solves assert
src/target/armv7m.c:222: armv7m_read_core_reg: Assertion
`num < (int)armv7m->arm.core_cache->num_regs' failed.
when gdb 'info reg' is issued on a Cortex-M target and
no cortex_m_debug_entry() has been called since OpenOCD start
(target was halted before OpenOCD start).
Change-Id: I32a2294693ef979b613be93aeceb3b0eb06ee6df
Ticket: https://sourceforge.net/p/openocd/tickets/216/
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5203
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Antonio Borneo
Adrian Negreanu
Yasushi SHOJI
Marc Schink
Tim Newsome
Peter Mamonov
Jan Matyas
Tarek BOCHKATI
Craig Blackmore
Tomas Vanek
Kevin Yang
Andreas Bolsch
Tarek BOCHKATI
Christopher Head
Evgeniy Didin
Sylvain Chouleur
Samuel Obuch
Tobias Kaiser
Daniel Trnka
Mete Balci
Tom Hebb
Stafford Horne
Jiuyang Liu
Samuel Obuch
Mikhail Rasputin
Jiri Kastner
Lucas
Khem Raj
Tommy Murphy
Ake Rehnman
iosabi
Kevin Burke
Florian Fainelli
Jan Matyas
Marc Schink
Matthias Welwarsky
Oleksij Rempel
Hsiangkai
Hsiangkai
bluew
Greg Savin
Bohdan Tymkiv
Andreas Fritiofson
darius-bluespec
Han Hartgers
dave-estes-syzexion
Nils Wistoff
jhjung81
Omair Javaid
Michael Schwingen
Paul George