Fixed flash page size detection according to EFM32 GG/LG errata.
MEM_INFO_PAGE_SIZE register containts invalid value in devices with
revision number lower than 18 and should not be used.
Change-Id: Idb2832246efcbbec2fd98a5c458f72a36df386fb
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1116
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently we have to supply the arg's to this cmd in a set order, this
change fixes that issue.
Change-Id: I14a15732e1917a91009e1ac14fba39ca1523c739
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/992
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Make sure we do not mask out the BFB2 boot bank bit, as this is used on
the larger XL devices.
Change-Id: Iacfdf874140e409e0c4ca9b9aee8f5c2f90dc9be
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/991
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The STM32F0 and F3 devices use a different default RDP to configure a
unlocked device, make sure we use that.
Change-Id: I170779461412c4c202c2cfc8d90baedb7e388150
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/984
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The user is able to use 2bytes of the options byte data for whatever
purpose they wish. Make sure we preserve this during an option erase/write.
Change-Id: Ibf951b11c59a148e671b1eb47fdc9b4f49ccae15
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/983
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Some debuggers (stlink) can't issue 16 bit writes and have to use a
loader to write flash memory.
Currently the loader is not used for option bytes, causing
stm32x_write_options to fail silently on such hardware.
Fix this by using stm32x_write_block to write option bytes as well.
Change-Id: I49c29d53ab5e162463cb349d4c89bef96467e587
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Reviewed-on: http://openocd.zylin.com/480
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The current stm32lx driver will fail if no working area is
provided - fallback to using slow writes if this is the case.
Change-Id: I92b1535fec4aebc855c63ce2c54b10f168f3c07e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1007
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updated as per ST RM0033 rev 5
Change-Id: I627fdab69b440b75b8e4f7c474216538fa5273a4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1001
Tested-by: jenkins
Other than a larger memory layout these new devices also have an extra
MER1 bit to perform the mass erase.
Change-Id: I7110a05bac95c1707160d1f5622181664291eb4a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/985
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Added in spi device table SPI Flash Winbond W25Q64CV 64Mbit
Its Device ID 0x001740ef is the same as Spansion S25FL064K (may
be a clone?)
Change-Id: I3cdbd182a0ccde75c78684cb9d54c76059bf34e0
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/928
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems ST have changed the ref manual (RM0313 rev1) and reverted to using
letters rather than numbers for the stm32f3x family.
Change-Id: I3a87ec9b0b2447d57dfef98603d30e28fe9ac927
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/926
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
Flash algorithm for LPC17xx/LPC2xxx was trying to "reuse" previously
allocated working area on next flashing which is not possible -
working areas are freed automatically on reset. This caused all but
first flashing attempts to fail. As there is no point in storing pointer
to working area, it was converted to local variable.
Change-Id: I939946325ff9eecc4861c0f51ab0f73871a3d7b9
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do some cleanup in lpc2000.c - concatenate short lines into single
longer lines, move variable declarations to "just before" they are
used, etc.
Change-Id: Ia7b9f0307dd4857ee8e15c8a6d4d7b5c4392fd80
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/861
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
No change to code, just fix some formatting issues.
Change-Id: I177430a99bfecbf90a1ddf623321c29d4db516b0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/906
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The erase time for the option byte page is not directly specified but is
assumed to be the same as the other pages (or mass erase) which is 20 to
40 ms. The current timeout value is 10 which means 10 ms plus the time to
poll the status flag that many times.
With faster interfaces or drivers (such as when using the ftdi driver
instead of the ft2232 driver) the adapter delay is not enough in some
cases, unless the jtag freq is reduced as a workaround. The result is a
"timed out waiting for flash" error when trying to write the options.
Increase the timeout to a minimum of 100 ms, which is in line with the
other erase timeouts. Also make defines of both the erase and the program
timeouts.
Change-Id: Ia86e71505033c52b60ef30092000689fbb547a18
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/902
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The pointer must be non-null here since we returned if allocation failed.
Change-Id: I9b75099ed3b3870c815d1df5760ed1f3fe1d20d6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/866
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Working area pointers shouldn't be re-used, so there's no point in storing
them in the flash bank struct. Make all such pointers local.
Change-Id: Iab65b4e8b475fed7fc72fb8928f54590fa69d260
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/865
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In FLASHD_ErasePages AT91C_EFC_FCMD_EPA is used to erase sectors.
According to the datasheet FARG[15:2] defines the page from which
the erase will start.This page must be modulo 4, 8, 16 or 32
according to the number of pages to erase. FARG[1:0] defines the
number of pages to be erased. Previously (firstpage << 2) was used
to conform to this, seems it should not be shifted... Changed it
to (firstPage) | erasePages.
Change-Id: I791cc7fc4faf056623ad5a6c7e860315306098a1
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/830
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Moved common SPI flash driver code (device table,
common commands) into flash/nor/spi.c and spi.h.
Updated flash/nor/stmsmi.c to reflect this refactor.
Change-Id: I141644b0af71d3835f29f06dd15b505a00e5b6ec
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/782
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stlink interface currently does not support 16bit read/writes.
Until a fix is included we issue a error that this is unsupported.
Change-Id: I4552cf2bd3b29e90ecc905325b743c08e2b92d67
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/808
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In at91sam3.c for Atmel SAM3 flash support, there are arithmetic errors in the functions sam3_page_read() and sam3_page_write().
Address locations are computed incorrectly due to an extra addition operation. This leads to memory locations being skipped during
flash writes and reads.
Smaller programs are written successfully into flash, with memory gaps, while larger programs of legitimate size fail because the
skipped memory is not utilized and therefore unavailable.
The changes address this condition, and have been tested with an Atmel SAM3X-EK evaluation board.
Change-Id: I9ea3b9ed0130b71cbc32b2294e31a6a2bc71b47a
Signed-off-by: Chuen Chou <zhouquan27@gmail.com>
Reviewed-on: http://openocd.zylin.com/806
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
In function pic32mx_write_block() if the parameter
offset is not a multiple of row size the row offset
(offset % row_size) will be ignored by the flash
controller, shifting the code to the beginning of
the row.
Word programming gets it right.
Change-Id: I134913e3d533688f791bbcb0c6e8983524197f3c
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Offset calculation into buffer was wrong and code would read outside buffer
if count was not a multiple of four.
Change-Id: Ied625b10221423d5a5f25d27ce1edd8c2c3eca8a
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/749
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The number if longwords or "sections" (Freescale term) written for a Kinetis
flash write (4, 8, or 16 bytes depending on the part density/granularity) are
now rounded up to ensure there are no truncations when the desired write is
not a multiple of the minimum write size.
Change-Id: I8db40a8769d8ac5393a46cbf4e5ff0df82faf916
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/738
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
For example in a pic32mx220, pic32mx unlock don't work
if adapter_khz is set to 5000 or more.
A short delay after asserting reset fix the problem.
Change-Id: I62e493edfcea585c36c8de77a969cebac7227b96
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/790
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Retest the condition when needed, instead of abusing the common_magic
field as a flag. There are only two options here. Either it's an armv7m or
it's another arm. is_arm(...) will return true even for armv7m, so it's
imperative to check in the right order.
Change-Id: Ic227f19f7babf1b0b0fe075f9a3abc4eabc7d5f1
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By Initialising the param_table we remove the clang warning's.
We are also make sure we are not passing any rogue values to lpc2000_iap_call.
Change-Id: Idb3b0077d1dae5f03dedab1d46d01140fe9ffb10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/777
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reorder to allocate all memory after COMMAND_PARSE_NUMBER call.
This removes a clang warning about un-released memory
Change-Id: I8dbeb664a6467077157015bd879bc0aefc5e8614
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/776
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the flash class was defined as FC_FLEX_RAM then this would always drop
through to the default handler.
This bug was found by clang, so untested.
Change-Id: I2d9fe6415dd216728a145519400f7b9ef1bd3c3a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/773
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
For odd byte counts, stm32x_write() pads the last byte and writes it using
a discrete 16-bit access. The stlink debugger can't issue 16-bit writes so
it fails for odd byte writes.
This patch changes stm32x_write() to pad odd byte writes into a new buffer
and use the normal code path with a single block write. The fallback path,
when working area cannot be allocated, has to use 16-bit writes though
which means that sufficient working area is required for stlink and odd
byte writes.
Change-Id: I4c5dc456300b6e1056f76b0095be8aceee3e954f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/756
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Remove a lot of the repetitive code in stm32f1x flash probe by converting
the large if-selector to a switch, moving the common checks outside it and
concentrating the failure handling to a single point.
Do the same with stm32f2x and stm32lx for consistency.
Change-Id: Ic0ecfb1533c49f5d2108cda5fd20c8372d7c71ef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/746
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some variants read 0 for the flash size register, rather than
failing lets assume we have max flash fitted.
Change-Id: Ie1fb4e73606f49268a6fd5921c3aef75bc4790d3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/744
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rather than failing if the flash size reg cannot be read lets assume
we have the max flash size fitted.
It is quite common on early ST silicon to not correct support this register.
Change-Id: Ife058d60ae0027faad2c929ebd5b7fe2ef27234d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/743
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Revision X is not mentioned in the latest RM0038 rev5, however it has been
confirmed correct by ST using ST-LINK Utilty.
Change-Id: I65210e512ea25818a1d0d3b223502ebd7535b29d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/742
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's unnecessary and prevents reusing this function to fix
option byte writes.
Also try to disable flash writing after an error.
Change-Id: Ib5a7b768a1523e6b8da1555126fef4c1e60ab083
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/479
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add support for the new stm32f3x family from stmicro:
http://www.st.com/stm32f3
Change-Id: Icd1db95bb2767d9c0ecef24deefa92b4fdaa4f14
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/735
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
New flash description for ATSAM3SD8C used on SAM3S-EK2 development boards. Name used
is "at91sam3sd8c" and chipid is 0x29ab0a60. Mirrors description of other similar parts.
Change-Id: I7fc4b82e7969451645ab067223663f08b76d866b
Signed-off-by: Mike Crowe <mpcrowe@gmail.com>
Reviewed-on: http://openocd.zylin.com/684
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In the previous iteration, the page counter for erases would not be updated with
the erase size. This patch keeps the page counter synced with the sector counter.
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Change-Id: I95e56a3257b2ad8301c9f28167b842fa6466334f
Reviewed-on: http://openocd.zylin.com/686
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updates the Kinetis NOR flash support to handle all known block and sector
sizes. Previously only 2kiB sectors were hard-coded, now all four known
combinations non-volatile sector sizes are supported.
The premise of separating Kinetis Program Flash (PFLASH) from FlexNVM is
also introduced. This means each "block" of flash (in Freescale terms) is
treated as a bank in OpenOCD. Correspondingly, the existing board
configuration for the TWR-K60M512 eval system is updated to recognize two
banks instead of one.
A board config for the TWR-K60F120M is also added.
Bank and sector erase and programming has been checked with both of the
mentioned eval boards.
Change-Id: Iae2d10ebf8f548d0a3698df5430bbbe1ccadc58a
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/663
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use default_flash_blank_check, this will use the much faster
blank_check_memory handler if supported - 15x quicker on stm32f4.
Otherwise it will fall back to using the slower default_flash_mem_blank_check.
Change-Id: Ia231b3e95468c9e92594dbdbe1fa2d69e1506fc3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/632
Tested-by: jenkins
cfi_spansion_write_block() passes an arm_algorithm struct to
target_run_algorithm() which in turn calls armv7m_start_algorithm()
which expect an armv7m_algorithm struct.
As armv7m_algorithm is bigger than arm_algorithm, when
armv7m_start_algorithm() writes in the struct, it overrun the buffer,
writting junk on the stack, which latter on generates a segfault.
This patch ensure we use a properly sized armv7m_algorithm struct
when the target is an armv7m.
Change-Id: I4ab67c15ae4bb72454414a81b92a4231dcdb2239
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/623
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
seems 9933fa334d introduce a regression
if the target was anything other than armv4_5 or armv7m.
Just check that we have an arm target.
Change-Id: I67c05138e5be2952ee92e9bfa15e1d050844462a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/615
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
check that the cfi driver supports the current target arch.
Change-Id: I8a95908684de67bf1657d1956f2573662a641cc1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/614
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
This makes the code a bit easier to read as arm_algorithm can
refer to other arch's, not just armv4_5.
Change-Id: I78c99d40f34cda04e06f2daee75b48ff40a1d23d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/613
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stm32f0 parts use a different address then the rest of the family.
Add a function that returns the correct FLASH_SIZE reg depending on variant.
Change-Id: Idb41580f7162f395b347cec034d6b745847326b7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/601
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The first available devkits for the at91sam3x8h had the ES device populated.
The ES device had an error in the CIDR, specifically in the last byte of
which the upper 3 bits identifies the chip family - cortex-m3, arm7tdmi etc.
The problem was fixed on the ES2 devices - Thanks to Pat Hickey for giving me
the heads-up.
Change-Id: I13dd7fbe0cffaf76f948188c9459dc3cf4435570
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/575
Tested-by: jenkins
Reviewed-by: Jim Norris <u17263@att.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The value returned from target_write_buffer is still ignored.
Change-Id: Icb49d4d1313a5e4f7df68d3f122a5f81cfa0604a
Signed-off-by: Linus Tolke <linus@tigris.org>
Reviewed-on: http://openocd.zylin.com/596
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The target address for the partial data needs to be bumped past the
full page data. Otherwise, the partial data overwrites the start of
the flash block.
Change-Id: I1246b2fa8acbdb8193edcf7029309f11d1c6069c
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/555
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add swd_init_reset and swd_add_reset.
Add adapter_assert_reset and adapter_deassert_reset, and call them instead
of JTAG reset functions.
Change-Id: Ib2551c6fbb45513e0ae0dc331cfe3ee3f922298a
Signed-off-by: Simon Qian <simonqian.openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/526
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add a warn message to inform the user that something is wrong
with the flash settings or command parameters.
Change-Id: Ia55868b2abf2a17845e51620b0f29b2809d841c2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/280
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch fix the slow flash write issue on pflash only devices.
The Family Reference Manual says:
For devices with FlexNVM: FlexRAM
For devices with program flash only: Programming acceleration RAM
So the acceleration RAM is available for the flash section command on
this device.
Change-Id: If6541a23a4457c5ed8858848a145f35cac63138b
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/509
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced 7 new Cortex-M3 processors on 2012-02-28
SAM3X4C - 256KB flash
SAM3X4E - 256KB flash
SAM3X8C - 512KB flash
SAM3X8E - 512KB flash
SAM3X8H (Only on dev-kit - not in production...) - 512KB flash
SAM3A4C - 256KB flash
SAM3A8C - 256KB flash
The SAM3X/A processors still suffer from the "6 waitstates needed
to program device" errata.
The CIDR address for the SAM3X/A processors are different from the
other SAM3 processors. Unfortunately, the chip identification register
is not at a constant address across all of the SAM3 series'. As a
consequence, a simple heuristic is used to find where it's
at... If the contents at the first address is zero, then we know
that the second address is where the chip id register is.
We can deduce this because for those SAM's that have the chip id @ 0x400e0940,
the first address, 0x400e0740, is located in the memory map of the Power
Management Controller (PMC). Furthermore, the address is not used by the PMC.
So when read, the memory controller returns zero.
Another interesting change is the flash bank address for flash bank 1.
It is not fixed at 0x00100000 like the Sam3U. Bank 1 of the at91sam3a/x
series starts at 0x00080000 + half the total flash size. Thus for the 256KB
devices Bank 1 is located at 0x000A0000, and for the 512KB devices Bank 1 is
located at 0x000C0000.
The configuration files for the SAM3X/A processors will follow
Change-Id: I6c3a707c00e05d993a2ad1d5a423f23b37ffd553
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/505
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The SUPC (Supply Controller) registers are on different base addresses on different
SAM3 chips:
SAM3U: 0x400e1210
SAM3N: 0x400e1410
SAM3S: 0x400e1410
This creates a problem with the sam3_reg_list array which is const, but would need
to be changed at runtime to account for this variability. As this register is not
used anywhere, it's simplest to just remove it.
Change-Id: I987eb371648d826aa6d5e9de18d38c7bb66d6fca
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/495
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Lock region count and sector sizes did not match datasheet.
(see 6500C-ATARM-8FE11 "SAM3S Series Datasheet", Table 7-1)
Change-Id: Ic511802f96ed03856467a24a6736349205a0576a
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/493
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The assert introduced in 00c8648351 checks
whether the programming offset equals to page_size of the flash, while it
wants to check whether the offset is a multiple of the page_size.
Change-Id: I794d021951a28c1cc520b5eea5d500f097721b06
Signed-off-by: Attila Kinali <attila@kinali.ch>
Reviewed-on: http://openocd.zylin.com/482
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Currently stm32lx flash driver will remove the readout protection if set
during a probe.
This may not be what the user wants, so let them decide.
Change-Id: I8575e3b339b10a4f7bac57cca9586dcab513d347
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/465
Tested-by: jenkins
This enable the stm32f2x flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 1048576 bytes from file stm32f4x.bin in 30.453804s (33.625 KiB/s)
after - wrote 1048576 bytes from file stm32f4x.bin in 23.679497s (43.244 KiB/s)
This also fixes a bug that was in the old flash loader.
The old loader waited while bit16 of the status reg was 0, the new
loader waits until this bit is 0 as stated in the flash spec.
Bizarrely this bug did not effect programming on any tested parts.
Change-Id: I3efc94d42cbe81283673a8f4203700638080af6e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/460
Tested-by: jenkins
This enable the Stellaris flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 65536 bytes from file test.bin in 5.486040s (11.666 KiB/s)
after - wrote 65536 bytes from file test.bin in 2.274001s (28.144 KiB/s)
Change-Id: I9004c9aadffa1ae3b0cbf908e6549b5b1f794508
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/403
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently the stm32f1x flash driver uses an asynchronous algorithm
as part of the block flash programming. This greatly speeds up flash
programming as the target is always running.
Moving the async code to the target enable other targets to use this
added functionality.
Change-Id: I8e53f094c2ef7848a7f86ddb9a35b6edbfc8454a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/402
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I used the CPUID instead of adding a new argument to the flash bank command
Fixed Type in comments
Add the failsafe return value in device_id
Change-Id: Ieb5a46fc002b5390a0c81bc8b49f6c687036ae1d
Signed-off-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-on: http://openocd.zylin.com/438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ref manuals for the stm32f2x (RM0033 Rev4) and stm32f4x (RM0090 rev1)
are unclear to the address of the flash size register (F_ID).
According to contacts @ ST this is the correct address, the manuals will be
updated in due coarse.
Change-Id: If9fb83b3100458d17038cf27c2b23355e1dc5a9e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/448
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: jenkins
This issue was caused by uncrustify not correctly converting the doxygen
comments.
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Change-Id: Ie6dc3b057a08603b670cb27312e5f0d989426e6c
Reviewed-on: http://openocd.zylin.com/431
Tested-by: jenkins
Correct the offset to the read pointer when clearing it on error.
Also restrict the instruction set to armv6-m so the flash driver can be
used on Cortex-M0 parts with the same flash controller.
Change-Id: I380f9dabcc41fb6e4d43a7e02f355e2381913f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/399
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
for some reason the following commit was incorrect
769064de4b
Only the Sandstorm and Fury class should write this register.
Change-Id: Ie18f1da6e9b59fb99cca47aa93c7f2fee447ccea
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/400
Tested-by: jenkins
For example, when blocks 2 and 3 were erased, openocd reported "erased blocks 2 to 4". That should be "2 to 3", I think.
Change-Id: Icece63dedd3dd931b70fa73616819a19572e39de
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/385
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SPAS register (OOB size) is left wrong after reset with respect to 2KiB page NAND chip. That will lead to ECC errors after 'reset halt'.
Change-Id: If5a4685cb8d6be35879453951611ef1059da219c
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/384
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch is based on Erik Ahlén's work on i.MX35 NFC support. Basically it redefines the CCM.RCSR register which is in a different address in i.MX25.
Change-Id: Ia6faf9cb5efae5e564b72ef9a9b7c7f8bfde3ce0
Signed-off-by: Timo Ketola <timo@exertus.fi>
Reviewed-on: http://openocd.zylin.com/383
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
stellaris_set_flash_timing should only be used for Sandstorm and Fury
device classes.
Change-Id: Ib5eff9d954c039f2c5726a8ecc3ee45d1694cfd3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/389
Tested-by: jenkins
read the target class during probe and save for later use.
Change-Id: Ib3ad20edc7d206b7f434bdcc6b947e6a5f06dd1f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/388
Tested-by: jenkins
Nothing more than a name change, just to make reading
the code a bit simpler.
Change-Id: I73a16b7302b48ce07d9688162955aae71d11eb45
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/390
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This makes use of the newly introduced usage field in the flash bank
structure.
Also remove the assertion if usage field is null and
lets print a DEBUG_LOG message instead.
Change-Id: I384bf0e2c444fcc99deef73aec9ef01149a91c76
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/391
Tested-by: jenkins
we should have caught them all - hopefully.
Change-Id: I35435317fccaf5ad0216244d69f76db6857bb582
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/381
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This allows us to detect a device arrata where the device id returned is
incorrect.
This issue only effects stm32f4x Rev A silicon.
Change-Id: Ic9f4985f9abf562f97322dcf484199f0a4eb01bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/354
Tested-by: jenkins
The stm32 drivers have been using 0x7ff as the DEV_ID mask, this should
have been 0xfff.
Change-Id: I232469620969d6dd1b9a2a2aa15ec18b947dbb05
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/352
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is no need to use a while loop here. This patch simple copy
the last bytes with the system function.
Change-Id: Ibda72dca449746efeba5a1af2e45c5990f9cf347
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/364
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add checking of the current flash lock status before performing the unlock sequence (which would fail in an unlocked state)
Change-Id: I693294c9cd2f59e69cb5bf3338120052fd680b1e
Signed-off-by: Bruno FLEURETTE <bruno.fleurette@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/363
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This uses the same controller as the stm32f2x family.
Change-Id: I931a9ceb0cd1219514d14b8b59475179e543dd0f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/338
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
On wrong parameters a error is signalized to the calling function.
Change-Id: I484443fdb39938e20382edc9246d5ec546a5c960
Signed-off-by: Mathias K <kesmtp@freenet.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/282
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Add verification of the flash unlock sequence and return an error if the
flash is still locked.
Add mass erase subcommand.
Change-Id: Id586b1eaf983a3f25b933847dd6608c15bf0b07e
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/281
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Renamed all functions, enums, structs and defines from mx2/imx27 to mxc. This is in preparation of adding support for mx35 NFC(v2).
Change-Id: I92ad23f0cfab605215bbf0d5846c5c288423facf
Signed-off-by: Erik Ahlén <erik.ahlen@avalonenterprise.com>
Reviewed-on: http://openocd.zylin.com/267
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
when last==first==0 then mass erase is executed, it's faster.
the page marking was wrong in this case.
Change-Id: I5c579d59b5c4778cf057cb5986e086abdd4209b2
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/232
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the unlocking procedure erases the flash mem (even if it wasn't locked), so it should be marked as erased after unlocking.
Change-Id: I5cc6a1e1d6cf4e1f243de532eff54111ffd66187
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/222
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Don't call a variable num_pages if it holds the flash size. Also rearrange
flash size to num_pages calculation to avoid divide-by-zero if there will
be a device with < 1024 byte pages someday.
Change-Id: I2febea39694a2f9750de141f52ec88ae1599c086
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/211
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this at least checks the post conditions after convoluted code.
Change-Id: Idfa8cbedce5288d8bae5743687949f141dfb07b2
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/187
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Check whether the destination is in the program flash or NVM regions,
in the former case, use the normal longword mechanism, not the fast NVM
write.
Change-Id: I7366b7c8919928ee690252df83b99701776aee82
Signed-off-by: Tomas Frydrych <tomas@sleepfive.com>
Reviewed-on: http://openocd.zylin.com/194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Before this commit, openocd used to segfault when probing flash
of an at91sam7x512 (which contains 2 banks of flash). This was due
to the way it systematically insert a new flash bank without setting
its name.
Then, when get_flash_bank_by_name_noprobe() is called, it is doing
a strcmp() on the non-initialized bank->name.
This commit prevents allocation of second probed bank if it is already
allocated (for example, if it is set in a target config file). If a
new bank really needs to be allocated, it ensures that a default name
is set.
Change-Id: I38d15bef1fda2ec746efad37171975136cf7b371
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/171
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add flash waitstate support for Atmel SAM3 chips.
* Set default waitstates to 6, to workaround a silicon bug in the SAM3 family
This code has been tested on SAM3U4, SAM3N4 and SAM3N1
based on Change-Id: I477446f9bfb3e910ea3e2414a6e9a75beb14a214
by Jim Norris <u17263@att.net>
Change-Id: I8d360080f6968979ca5e197ad638282cadd18fb7
Signed-off-by: Attila Kinali <attila@kinali.ch>
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/128
Tested-by: jenkins
add support for checking target against the device CLASS rather
then just the PARTNO.
This change also adds the new LM4F family (Blizzard).
Change-Id: Ia9d1e33f1f1c2817c0039a2232ecf932fae072f9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/161
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
stick to convention of "retval" being used as error value to
be propagated and use "flash_flags" local variable for flash
flags read from how.
Change-Id: I63f1f2248b4f4538d6cd7634ae277f7c0aadc346
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/178
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
variable is subsequently not used
Change-Id: I177d21c6ba9f1f2e3765feffdbf317ea375a8cfe
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/149
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
found by clang, would have done something undefined and mysterious
later on.
Change-Id: If7d7aca8514575d229ed0b17378bf8b1bbf347c4
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/133
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The fix is inline with the Linux coding style that forbids
assignment in if condition
Change-Id: I10338a249bcfeff87d8596f7e17f209e26b41678
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/86
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The fix is inline with the Linux coding style that forbids
assignment in if condition
Change-Id: I42a371d6adfdf3b3fb867705211c47d89776ee2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/85
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Total of 5 warnings:
3x "Dead store": removed dead assignment to variable;
1x "Dereference of null pointer": this is not an error, but a
limited visibility of clang, since pointer erase_region_info
is initialized inside cfi_fixup_non_cfi();
1x "Branch condition evaluates to a garbage value":
this is a real coding bug that could issue SIGSEGV, since
"goto cleanup" can be executed before initialization
of "source".
Change-Id: Id3c323c82bb15cbd3bb8fc04b23541f11145f109
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/84
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This should silence a warning.
Change-Id: Id91a9ebacae836083b1db2654a8e7bf24b2300e9
Signed-off-by: Edgar Grimberg <edgar.grimberg@gmail.com>
Reviewed-on: http://openocd.zylin.com/52
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Let the target algorithm be running in the background and buffer data
continuously through a FIFO. This reduces or removes the effect of latency
because only a very small number of queue executions needs to be done per
buffer fill. Previously, the many repeated target state changes, register
accesses (really inefficient) and algorithm uploads caused the flash
programming to be latency bound in many cases. Now it should scale better
with increased throughput.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Access the different flash banks' registers using a bank specific register
base and a register specific offset. This is equivalent but feels more
natural.
Some accesses were discovered that maybe should not be hard coded to bank0
registers. Add a note about that.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
crc check was always performed on newly flashed data, now it is optional
flash mem can be locked by writing a specific word to a specific address in flash.
to verify flash, target must be halted, and this will (when the new halt sequence is implemented) require reseting the chip. if the target is reset after writing the lock words, then it will lock, hence the CRC will fail because it is not possible to read stuff from the target.
also added a function that resets the jtag state machine.
this is not used yet, but will be soon.
it is implemented to allow strict control over JTAG state machine, necessary to implement to halt and unlocking sequences.
Posted by telekatz@gmx.de in the bettyhacks forum for openocd
0.4.0 and integrated into 0.5.0 by Gunnar Henne.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
There are some older atmel nor chips which have negated logic for
TopBottom detection. This patch adds a special handling for the old
chips. This is the same mechanism as implemented in linux kernel.
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
Issue warning when the old cmd is used and redirect to new supported one.
These deprecated cmds will be removed at some point.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Use consistent names for the stm32 family flash drivers, eg.
stm32x -> stm32f1x
stm32f2xxx -> stm32f2x
this makes it easier to add support for newer stm32 families.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
there was a check in clearing the status register that
called exit() if the target was running. target_write_memory()
has such a check and will report the error correctly.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Update devices as per the latest programming manual.
We now use the full DEVID to identify the target. Previously we used
a 8bit id but that has now been changed in the manual.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
production processor versions increment, thus the version
bits should be ignored for future proofing. e.g.
Engineering sample version == 0x00, production version 0x01
Fix a bunch of typos.
Most are in code comments, so nothing should break. UNKOWN_COMMAND and
CMD_UNKOWN are not used elsewhere, so correcting the spelling should
also not break anything.
Based on the lpc3180 driver, but released as a separate driver for two reasons:
1) I don't have an lpc3180 to test it against, so it might unintentionally break compatibility.
2) It's using a different OOB layout than lpc3180.
Rewritten so that it no longer borrows code from the NXP CDL library. Instead borrowing code from the u-boot port to lpc32xx, written by Kevin Wells.
Tested on lpc3250 (Hitex LPC3250-Stick). OOB layout is compatible with LPCLinux.
ARM11 broke with aa61a3b3d8
as the code only checked for arm 7/9.
CFI probably needs work for non-ARM targets but perhaps
not adding working area memory to e.g. MIPS will give
the default slow CFI support.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Added a Perl script to contrib that uses the header files in StellarisWare complete Firmware Development Package provided by TI/Luminary to generate a new list of device IDs
Used Perl script and revision 6734 of TI/Luminary StellarisWare to update device IDs
Hi,
I took the stm32x NOR flash driver and adapted it for the Ember EM357
chip. This chip is very similar to em351 and stm32w so the driver
should be easily extended to support those as well if anyone can get
their hands on some of those for testing.
changelog:
Added NOR flash driver em357
Best regards,
Erik Botö
Find the flash controller by position since it is before the core,
not after it.
This fixes the problem that str9xpec enable_turbo (or any other
str9xpec command) did not work. (See my post in
http://forum.sparkfun.com/viewtopic.php?f=18&t=25542)
Signed-off-by: Santeri Salko <santeri.salko@gmail.com>
Remove extra \n from LOG_DEBUG, LOG_INFO, and LOG_WARNING messages
Remove LOG_INFO_N
LOG_INFO_N was only used once and had a \n at the end
Change LOG_USER_N calls that end with \n to LOG_USER
Do not propagate error number to user. This is for internal
programming purposes only. Error messages to the user is
reported as text via LOG_ERROR().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Every NAND driver keeps private copy of "target"
structure.
Prepare infostructure to move private "target"
copy in common/shared struct nand_device.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Table of NAND devices reports operating voltage.
Replace comma with proper decimal dot.
Øyvind: "." is correct for UK/US, but incorrect for
many other languages. OpenOCD is not localized at this
point, so sticking to "." for US/UK should be OK.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
From struct nand_flash_controller :
- remove unused field register_commands;
- remove field controller_ready, exported but
never referenced.
Remove dead code pointed by controller_ready.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
I received a number of "-Wshadow" related warnings (treated as errors) while
trying to build on OS X Leopard. In addition, there were two miscellaneous
other warnings in the flash drivers. Attached are two patches which correct
these issues and the commit messages to accompany them.
My system has the following configuration (taken from uname -a):
Darwin 9.8.0 Darwin Kernel Version 9.8.0: Wed Jul 15 16:55:01 PDT 2009;
root:xnu-1228.15.4~1/RELEASE_I386 i386
=== Werror_patch.txt Commit Message ===
compilation: fixes for -Wshadow warnings on OS X
These changes fix -Wshadow compilation warnings on OS X 10.5.8
Compiled with the following configure command:
../configure --prefix=/usr/local --enable-maintainer-mode --enable-jlink
--enable-ft2232_libftdi
=== flash_patch.txt Commit Message ===
compilation: fixes for flash driver warnings on OS X
These changes fix two compilation warnings on OS X 10.5.8:
../../../../src/flash/nor/at91sam3.c:2767: warning: redundant redeclaration
of 'at91sam3_flash'
../../../../src/flash/nor/at91sam3.c:101: warning: previous declaration of
'at91sam3_flash' was here
and
../../../../src/flash/nor/stmsmi.c:205: warning: format not a string literal
and no format arguments
Compiled with the following configure command:
../configure --prefix=/usr/local --enable-maintainer-mode --enable-jlink
--enable-ft2232_libftdi
===
Andrew
The flash bank name is a required element in adding flash banks,
however other than looking at the config file there is no way of
getting the name used in openocd.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
add supoort for xl family boot bank option.
The option byte handling will be cleaned up in a later patch.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch adds the initial dual flash bank support for devices such
as the stm32xl family.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
the unprotect fn in stm32 needs to unprotect more sectors
than was requested aligned to some boundary.
Print warning when this happens.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
some chips unprotect more than the range asked for. The
protect fn, must unprotect/protect minimally the range given.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Some flash's do not support buffer writes, so we now check
they are supported before trying to use them.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The existing code used incorrect timeout values for the various cfi
operations. We now calculate the timeouts and convert to
msecs if necessary.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
STMicroelectronics controller SMI is not SPEAr specific.
Rename it and change name to every symbol in the code.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Modified spearsmi driver to include support for STR75x
Added missing initialization in tcl file for STR750
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
If flash chip is not listed in the table, or if no flash is
connected, pointer must be properly initialized.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
flash programming via flash write_image or gdb load would
produce a bogus error message that the flash chip was to
small.
The solution is to limit the current flash programming
run to the current chip.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
SMI interface hides the real SPI bus between SPEAr and
external flash.
Added comments to highlight the SPI operation, to help a
future rework in SPI generic and SPEAr specific drivers.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add comments to assembly flash loader for STM32. Add tiny improvement in
size of the algorithm (40 vs 48 bytes) and tiny speed improvement (~1.5%,
as time is wasted on waiting for end of operation anyway).
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
add missing error handling.
Output warning when assuming maximum flash size in the
family when failing to read.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
for non_cfi cfi chips free() was invoked on rodata.
The mystery is why this bug has survived for so long.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
sizeof() is a bit less scary than seing assumption
about size of type, no bug as such.
Use NULL instead of 0 for pointers. More obvious that
it is a pointer from code inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
The patch improves flash erase for STR9x in case of a full bank erase.
Then the chip erase command is used instead which improves speed significantly.
Also I think it might help if e.g. STR912 enters some state where flash banks are locked, and a chip erase command is the key for unlocking the flash.
This flash driver works on more than just two chips.
(Though it does need work still, e.g. to protect more than 64K.
(On non-'3748-A0 chips where errata allow that.))
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For the above targets the exit_point is
optional when used with run_algorithm, so remove it.
This makes updating the algorithm less error prone.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Review allocation of error numbers in openocd
to avoid overlap.
Put brackets around negative numbers to avoid
issues during macro expansion.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add "static" qualifier to private functions.
Move duplicated global declarations from "target/avrt.c"
and "nor/avrf.c" to "target/avrt.h".
Remove unused declarations form "nor/avrf.c".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Helper ./src/helper/membuf.c is only used in at91sam3.c
1) Replace membuf with LOG_*
2) The original code in sam3_GetDetails() invalidates
all the buffered output of sam3_GetInfo(). The new
code skips sam3_GetInfo() if its output should not
be printed.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
when the verify failed, it didn't return an error,
which breaks e.g. tcl scripts that rely on this for
exceptions to work.
Found by -Wshadow
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
found by code inspection. There are many other places in
CFI where LOG_ERROR() should be called similarly...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when a write/unlock/erase failed during write_image, then
an error was not propagated back up so e.g. flash write
image from tcl scripts would not throw an exception.
Also flash filling speed was printed even when the
operation failed. Output is now less confusing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
any read/write operation to memory can fail.
block write algorithm error propagation was broken
in that it would continue after an error was reported
writing data to ram or the algorithm failing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hello,
"stm32x mass_erase" return ERROR_OK even if something goes wrong.
Here is a summary of changes :
* in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error
detected in FLASH_SR register;
* in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the
returned value of stm32x_mass_erase().
I don't know if there is reason to always return ERROR_OK ?
Gaëtan
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Every time command "flash probe #" is executed, memory
structures are re-allocated without preventive free()
of former areas, causing memory leak.
Also, memory allocation does not check return value,
determining segmentation fault in case of out of memory.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
Page reads using hwecc4_infix layout segfaulted for check_bad_blocks because
the read assumed a valid data buffer, which check_bad_blocks does not use
(it only passes a 6 byte buffer for the start of OOB).
This version copes with undersized or missing data or oob buffers and uses
random read commands within the page to skip unwanted areas of data/OOB for
speed.
NOTE: Running check_bad_blocks with this layout will be reading infix
OOB locations, not manufacturer bad block markers. This means that if you
check blocks written in infix layout they will appear good, but manufacturer-
marked bad blocks may also appear good.
If you want to scan for manufactuer-marked bad blocks, you need to enable
raw_access before running check_bad_blocks, or use the non-infix layout.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
CC: David Brownell <dbrownell@users.sourceforge.net>
nand_build_bbt() was ignoring the return value from nand_read_page() and
blindly continuing.
It now passes the return value up to the caller if the read fails.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Change download rate messages about kibibytes from "kb/s" to "KiB/s" units.
See: http://en.wikipedia.org/wiki/Data_rate_units
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Remove few LOG_DEBUG() messages, together with code and
variables required to build such messages.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final step to force bus_width size during CFI flash
read.
Added CFI specific implementation cfi_read() that uses
only accesses at bus_width size.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
During cfi_write(), head and tail of destination area
could be not aligned to bus_width.
Since write operation must be at bus_width size, source
buffer size is extended and buffer padded with current
values read from flash.
Force using bus_width to read current value from flash.
Do not use cfi_add_byte() anymore, to allow removing this
function later on.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
NOR flash structure requires each access to be bus_width wide.
Fix read of flash ID accordingly to rule above.
Add case (chip_width == 4), allowed by CFI spec and coherent
with current value of CFI_MAX_CHIP_WIDTH but currently not
used by any target.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Since NOR flash devices does not handle "byte enable lanes",
each read/write access involves the whole "chip_width".
When multiple devices are in parallel, usually all chips are
enabled during each access.
All such cases are compatible with flash accesses at
"bus_width" size.
Access at "bus_width" size is mandatory for write access to
avoid transferring of garbage values to flash.
During read access the flash controller should take care,
and discard unneeded bytes. Anyway, it is good practice to
use "bus_width" size also for read.
Every memory access that does not respect "bus_width" size
is marked with a "FIXME" comment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Review and simplify computation of bufferwsize.
Add comments about variables' meaning.
The same code is present 3 times in the file.
Current patch updates all the 3 instances.
Step 1)
Replace "switch(bank->chip_width) {...}".
Illegal values of bank->chip_width are already dropped.
For legal values, the code is equivalent to:
bufferwsize = buffersize / bank->chip_width;
Step 2)
The above code replacement plus the following line:
bufferwsize /= (bank->bus_width / bank->chip_width);
is merged in a single formula:
bufferwsize = (buffersize / bank->chip_width) /
(bank->bus_width / bank->chip_width);
and simplified as:
bufferwsize = buffersize / bank->bus_width;
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Arguments chip_width and bus_width of command "flash bank" are
not fully checked.
While bus_width is later on redundantly checked in several other
parts (e.g. in cfi_command_val()) and generates run-time error,
chip_width is never checked, nor related to actual bus_width
value.
Added check to avoid:
- (chip_width == 0), that would mean no memory chip at all,
avoiding also division by zero e.g. in cfi_get_u8();
- (bus_width == 0), that would mean no bus at all;
- unsupported cases of chip_width or bus_width value not power
of 2;
- unsupported case of chip width wider than bus.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Last block was being skipped, fix by changing the loop test from "<" to "<="
First block argument was ignored, always started from block 0 (and counted
the wrong blocks as bad if first was nonzero). Now we use it.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The last_block argument to nand_erase() is checked against nand->num_blocks,
but the highest valid block number is (total - 1), the test for invalid should
be ">=" rather than ">".
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
flash cmds can now be passed either the bank name or the bank number.
For example.
flash info stm32.flash
flash info 0
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Hi,
This is my first post to the list. First, I would like to thank
everyone for their work on OpenOCD, it is a great tool to work with. I
have been using it to debug code on hardware for the Rockbox project
(www.rockbox.org).
The target that I primarily work with has a Spansion/Fujitsu NOR flash
(MBM29SL800TE). I attached a patch that adds support for this flash. I
hope it can be included in the main repository. If there is something
that needs to be changed with the patch before inclusion please let me
know.
-Karl Kurbjun
The ST/Numonix M29W128G has an issue when a 0xff cmd is sent,
it cause an internal undefined state. The workaround according
to the Numonyx is to send another 0xf0 reset cmd
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
There are a million reasons why cached protection state might
be stale: power cycling of target, reset, code executing on
the target, etc.
The "flash protect_check" command is now gone. This is *always*
executed when running a "flash info".
As a bonus for more a more robust approach, lots of code could
be deleted.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove/fix lots of bugs in handling of non-contigious sections
and out of order sections.
Fix a gaffe introduced in previous commit to src/flash/nor/core.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove bogus error messages when trying to allocate a
large chunk of target memory and then falling back to
a smaller one.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The current timeout for STM32 flash block erase and flash mass erase is
10 (ms), which is too tight, and fails around 50% of the time for me.
The data sheet for STM32F107VC specifies a maximum erase time of 40 ms
(for both operations).
I'd also consider it a bug that the code does not detect a timeout, but
just assumes that the operation has completed. The attached patch does
not address this bug.
The attached patch increases the timeouts from 10 to 100 ms. Please apply.
/Tobias
Fix a bug where write_image would fail if the sections
in the image were not in ascending order. This has previously
been fixed in gdb load.
Solved by sorting the image sections before running flash
write_image erase unlock foo.elf.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this is done for unlocking and it is a simple omission that
it wasn't done for sectors.
The unnerving thing is that nobody has complained about this
until now....
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the flash has not yet been probed and GDB connects while the target is
running, the flash probe triggered by GDB's memory map read will fail. In
that case the returned memory map will be empty, causing a subsequent load
from within GDB to fail. There's not much you can do from GDB to recover,
other than a restart; a 'mon reset init' and manual 'mon flash probe' won't
help since GDB has already made up its mind about the memory map.
It seems there's no reason to require the target to be halted when probing
the flash. Remove the check to let a valid memory map be provided to GDB
even when connecting to a running target.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The The patch labeled "CFI CORE: bug-fix protect single sector" was merged
rged without some requested bugfixes. Most significantly it broke invariants
in the code, invalidating descriptions and changing the calling convention
for underlying drivers. (It (Also wasn't CFI-specific...)
Fix that, and Include an update from Antonio Borneo for the degenerate
"nothing to do" case, (although that's still in the wrong location. which
is presumably why that is it was working in some cases but not all.)
src/flash/nor/core.c | 21 ++++++++++++++++-----
1 file changed, 16 insertions(+), 5 deletions(-)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Arguments for "flash bank" command are already
parsed and put in "bank" struct.
Removed code to parse them again.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Syntax of "flash bank" command requires:
- chip_width as CMD_ARGV[3]
- bus_width as CMD_ARGV[4]
Actual code swaps the arguments.
Bug has no run time impact since wrong variables
are only used to check value and both are checked
against same constraint.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
The command "flash bank" has updated syntax.
Add the mandatory parameter <target> to the usage message
that prints in case of error.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
jtag_get/set_end_state() is now deprecated.
There were lots of places in the code where the end state was
unintentionally modified.
The big Q is whether there were any places where the intention
was to modify the end state. 0.5 is a long way off, so we'll
get a fair amount of testing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Until this time only basic SLC functionality exists when you want to use SLC to access external nand flash.
Basic functionality can be selected with command:
lpc3180 select 0 slc
It is anyway very slow to write/read to/from nand flash.
With the new command, SLC speed improved about 20 times, and hardware ECC info also read/written from/to nand flash OOB area:
lpc3180 select 0 slc bulk
Speed improvement achieved by using working are in SRAM of the LPC3250 chip and controlling DMA controller to interact between SRAM and SLC peripheral.
Here are the patches, and if they are ok than take them.
Tested with hitex LPC3250 usb stick.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Fixes bug that prevented users from specifying a base address of
0x80000000 or higher in image commands (flash write_image, etm image,
xscale trace_image).
image.base_address is an offset from the start address contained in
the image file (if there is one), or from 0 (for binary files). As a
signed 32-bit int, it couldn't be greater than 0x7fffffff, which is a
problem when trying to write a binary file to flash above that
address. Changing it to a 64-bit long long keeps it as a signed
offset, but allows it to cover the entire 32-bit address space.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Cannot protect or unprotect single sector in cfi flash.
When first==last the procedure fails.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
At the end I have added comments /* FIXME: to be removed */
There are 3 lines in which my simplification is not complete due to
data dependency with LOG_DEBUG() messages visible in the patch.
Such log_debug has been introduced on Jan 22, 2007 with commit
4fc97d3f27 during development activity
in this file/procedure.
From my point of view, these logs can be removed, since not part of a
consistent flow of information.
Alternatively, could be borrowed in the new cfi_send_command(), but
this will increase verbosity.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
In the code a single field was all that was ever used. Makes
jtag_add_ir_scan() simpler and leaves more complicated stuff
to jtag_add_plain_ir_scan().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
jtag_add_dr/ir_scan() now takes the tap as the first
argument, rather than for each of the fields passed
in.
The code never exercised the path where there was
more than one tap being scanned, who knows if it even
worked.
This simplifies the implementation and reduces clutter
in the calling code.
use jtag_add_ir/dr_plain_scan() for more fancy situations.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
JEDEC standard reports Vpp integer part encoded as 4 bit HEX value.
To print it using decimal digits, %u is required.
Other voltage values are coded as BCD, so %x is appropriate.
Code already prints one nibble at a time, so no need for field width
and precision in format string.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When the beginning or end of the specified range of sectors
already has the requested protection status, don't ask the
flash driver to change those sectors.
This will among other things turn command sequences like
this into the NOPs one would expect:
flash protect_check 0
flash info 0
... reports everything as unprotected ...
flash protect 0 0 1 off
That speeds things up (by whatever work was just avoided).
Also, with Stellaris (which can't unprotect flash at page level)
this can eliminate some undesirable/false error reports. (And
finishes fixing a bug currently listed in our bug database...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The NOR infrastructure caches some per-sector state, but
it's not used much ... because the cache is not trustworthy.
This patch addresses one part of that problem, by ensuring
that state cached by NOR drivers gets invalidated once we
resume the target -- since targets may then modify sectors.
Now if we see sector protection or erase status marked as
anything other than "unknown", we should be able to rely
on that as being accurate. (That is ... if we assume the
drivers initialize and update this state correctly.)
Another part of that problem is that the cached state isn't
much used (being unreliable, it would have been unsafe).
Those issues can be addressed in later patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Give a more accurate failure message when trying to unprotect; don't
complain about pages being write protected, just say that unprotect is
not supported by the hardware ... referencing the new "recover" command,
which is the way to achieve that.
Likewise, when trying to protect, talk about "pages" (matching hardware
doc) not "sectors" (an concept that's alien to these chips).
Also make the helptext for the "recover" command mention that it
also erases the device.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix some issues with the generic LPC1768 config file:
- Handle the post-reset clock config: 4 MHz internal RC, no PLL.
This affects flash and JTAG clocking.
- Remove JTAG adapter config; they don't all support trst_and_srst
- Remove the rest of the bogus "reset-init" event handler.
- Allow explicit CCLK configuration, instead of assuming 12 MHz;
some boards will use 100 Mhz (or the post-reset 4 MHz).
- Simplify: rely on defaults for endianness and IR-Capture value
- Update some comments too
Build on those fixes to make a trivial config for the IAR LPC1768
kickstart board (by Olimex) start working.
Also, add doxygen to the lpc2000 flash driver, primarily to note a
configuration problem with driver: it wrongly assumes the core clock
rate never changes. Configs that are safe for updating flash after
"reset halt" will thus often be unsafe later ... e.g. for LPC1768,
after switching to use PLL0 at 100 MHz.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
windows api does not define a posix sleep, use usleep that
has an openocd wrapper to the win32 native function.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- armv7m_run_algorithm now requires all algorithms to use
a software breakpoint at their exit address
- updated all algorithms to support this
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Stellaris chips have a procedure for restoring the chip to
what's effectively the "as-manufactured" state, with all the
non-volatile memory erased. That includes all flash memory,
plus things like the flash protection bits and various control
words which can for example disable debugger access. clearly,
this can be useful during development.
Luminary/TI provides an MS-Windows utility to perform this
procedure along with its Stellaris developer kits. Now OpenOCD
users will no longer need to use that MS-Windows utility.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I have successfully programmed the AT90CAN128, based on the mega128
with some small modifications.
[ dbrownell@users.sourceforge.net: patch cleanup ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Issue warning to user when unlocking or writing the option bytes.
The new settings will not take effect until a target reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Issue warning to user when unlocking or writing the option bytes.
The new settings will not take effect until a target reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The default state of the STR7 flash after a reset init is unlocked.
The information in the flash driver now reflects this.
The information about the lock status cannot be read from the
flash chip, so the user is informed that flash info might not
contain accurate information.
[dbrownell@users.sourceforge.net: line length shrinkage]
Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The "NOR: last_addr also needs correction when checking alignment"
patch omitted a necessary update to the key diagnostic; fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
According to OpenOCD error handling rules the error is
logged at where it occurs(same site where an exception
would have been thrown).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The LPC3180 NAND driver was crashing on some large page chips.
Fix:
- Crash and related functionality (don't memset too much OOB data)
- Some debug messages
- Command handling now works
[dbrownell@users.sourceforge.net: whitespace/linelength/message cleanup]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Identical to the existing 2412/2443 support except for the base address
and NFCONF value (bit 2 is reserved and should be written as 1 ref UM).
Tested on a s3c6410 board, but controller is identical in 6400/6410
except for 8bit MLC ECC support in 6410 which isn't supported by the
driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Using the erase bank command will cause a time out error. Replacing
this with the erase sector bank will provide a slower but safer and
stable method to erase the flash.
Signed-off-by: Laurentiu Cocanu <laurentiu.cocanu@zylin.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines; fix some bad indents.
Add TODO list entry re full support for NAND/NOR bank names.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Usage messages should use the same EBNF as the User's Guide;
no angle brackets. Be more complete too ... some params were
missing. Improve and correct various helptexts.
Make user's guide refer to the NAND "driver" name, not the
controller name; that's a bit more precise.
Don't use "&function"; its name is its address. Line up struct
initializers properly. Remove some blank lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It can invalidate ECC codes, and in general is not guaranteed
to work. (However on some chips it _appears_ to behave.) Just
don't do it; don't write in those cases.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Much to my surprise, I observed a "flash erase_address ..."
command erasing data which I said should not be erased.
The issue turns out to be generic NOR flash code which was
silently, and rather dangerously, morphing partial-sector
references into unrequested whole-sector ones.
This patch removes that low-level morphing. If desired, it
can and should be done in higher level code. (We might need
to fix some stuff in the GDB server code.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's currently allocating a big buffer but writing it out in
units of sizeof(host's pointer) ... sub-optimal.
Plus fix a couple minor coding style goofs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Word count == size/4; cope. And increase buf_min so it's large
enough to cover the overhead in my tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Try to right-size the SRAM buffers, by not:
- using them for very small writes
- giving up when a large buffer isn't available
- allocating buffers much larger than their data
Also don't:
- bother loading the code unless we allocate the writebuffer too
- be so verbose with messaging:
* be more concise
* reduce importance (e.g. DEBUG not WARNING)
* remove duplication
The minimum buffer size is something of a guess. It's eight
times smaller than before, almost the same size as the code
being downloaded. It probably deserves some tuning.
Also, note an erratum affecting flash protection on some chips;
and narrow many over-wide lines affected by the above changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Refactored the write page raw function into two new functions
for writing data to a NAND device and then another function to
finish up a write to a NAND device. This includes some new
updates to introduce more error checking to existing code.
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Added a new function to encapsulate reading a page of data from
a NAND device using either the read_block_data function of a NAND
controller or to use direct reading of data from the NAND device.
This also adds some performance enhancements and uses the read_data
function if the read_block_data function fails safely (because it
can't allocate a buffer in the working area).
[dbrownell@users.sourceforge.net: fix fault handling, whitespace]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Someday revisit various issues: Tempest parts support writing
more than one word at a time; for some target firmware it might
be necessary to save and restore flash IRQ configuration. (The
safest policy is likely to always reset after flash updates.)
Plus swap some undesirable TAB characters with SPACE.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix potential memory leak: make sure the per-bank data
structures are only allocated in probe(), and that calling
probe() multiple times is a NOP. Use it for auto_probe().
Require probe() to have done its thing: don't make access
routines cope with it not having been called. Shrink a
bunch of failure paths; and in some cases, correct them.
Don't needlessly insist on a halted target for probe().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No point in reading and discarding a status value when fetching
part description data. Or having that needless "#if 0" code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously "reading" clock info (and part info) also, as a side
effect, wrote the flash timing register. Instead, be more safe:
"reading" should only read. Write paths still refresh timing,
coping with changes the application code may have made.
Also rename the routine which sets flash timing, indicating what
it's really doing; it's got nothing to do with a "mode".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I added the remaining devices and device IDs to stellaris.c, and
removed several devices that don't exist on the Stellaris web page.
Additionally, I found a few devices with duplicate IDs ... the DID1
Version Number for LM3Sxxx parts have DID1 Version = 0x0, and for
LM3Sxxxx have DID1 Version = 0x1. So I extended the comparison to
use the VER and FAM fields from DID1 also.
ID=0x33: LM3S812 (DID1v0) and LM3S2616 (DID1v1)
ID=0x39: LM3S808 (DID1v0) and LM3S2276 (DID1v1)
These are the parts I removed from the file for lack of documentation
(no data sheet to confirm part ID):
LM3S318,
LM3S1101, LM3S1108,
LM3S1615, LM3S1616,
LM3S2016,
LM3S2101, LM3S2108,
LM3S3759, LM3S3768,
LM3S5757, LM3S5767, LM3S5768, LM3S5769,
LM3S6815, LM3S6816,
LM3S6915, LM3S6916,
LM3S6111, LM3S6118.
Also, sort devices according to part number.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Bugfix the read side of flash protection:
- read the right register(s)!
- handle more than 64K
- record the results in the right places
- don't display garbage.
Partially bugfix the write side:
- use 2KB lock regions instead of 1KB pages (!)
- validate input range
- don't try to _remove_ protection (it's write-once)
- #define values we'll need to commit writes.
- ... still doesn't handle pages over 64KB mark, or commit writes
And minor cleanup and fixes:
- get rid of some forward decls
- properly locate a doxygen comment
- fix some bad indentation
- remove superfluous #include
- add a new part ID (many are still missing)
- make the downloaded algorithm code be read-only
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move most declarations in <target/armv4_5.h> to <target/arm.h>
and update users.
What's left in the older file is stuff that I think should be
removed ... the old register cache access stuff, which makes it
awkward to support microcontroller profile (Cortex-M) cores.
The armv4_5_run_algorithm() declaration was moved too, even
though it's not yet as generic as it probably ought to be.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the ARM opcode macros from <target/armv4_5.h>, and a few
Thumb2 ones from <target/armv7m.h>, to more appropriate homes
in a new <target/arm_opcodes.h> file.
Removed duplicate opcodes from that v7m/Thumb2 set. Protected
a few macro argument references by adding missing parentheses.
Tightening up some of the line lengths turned up a curious artifact:
the macros for the Thumb opcodes are all 32 bits wide, not 16 bits.
There's currently no explanation for why it's done that way...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the existing 'flash banks' implementation as 'flash list', and
replace the broken 'flash_banks' TCL wrapper with a new command handler.
Adds documentation for the new 'flash list' command in the user guide.
The 'flash banks' command produces a list that needs to be formatted
properly for GDB's 'mem info' to work properly. The flash_banks TCL
wrapper provided this formatting, but wrappers no longer work for
second-level commands as they did in the past. With this patch,
the 'flash_banks' command can be used with the new command syntax
and display the required information.
More updates from the code review by Steve Grubb <sgrubb@redhat.com>.
The Jim float-comparision bug just gets a comment not a fix, though.
Cc: Steve Grubb <sgrubb@redhat.com>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename nand.h as flash/nand/core.h, chase consumers. The public APIs
need to be sorted out with imp.h, but this allows other changes to
begin improving the separation between policy and mechanism.
Moves #include <target/target.h> and #include "driver.h" into the
internal headers or source files, removing it from <flash/nand/core.h>.
Moves commands into nand/tcl.c and core implementation to 'nand/core.c'
and 'nand/fileio.c'. Eliminates 'flash/nand.c'.
Adds 'nand/imp.h' to share routines between TCL commands and core.
This work parallels the NOR directory, encapsulating the NAND drivers
into a separate file. This takes an extra step by encapsulating the
type of data structure used to manage the drivers, allowing it to be
changed from an array to a dynamic list in the future.
Move the bulk of the flash.h file into flash/nor/core.h, leaving an
empty husk that will be removed in the next patch.
The NOR driver structure is an implementation detail, so move it into
its own private header file <flash/nor/driver.h> along with helper
declaration for finding them by name.
Splits the exec mode commands out of flash.c into the flash/nor/ files.
The routines used by these high-level commands are moved into nor/core.c,
with their internal declarations placed in nor/imp.h.
Fixes distribution of <flash/nor/core.h> header.
The newly moved flash TCL routines access the internals of the module
too much. Fix the layering issues by adding new core NOR flash APIs:
<flash/nor/core.h>:
- flash_driver_find_by_name() - self-descriptive
<flash/nor/imp.h>:
- flash_bank_add() - encapsulates adding banks to bank list
- flash_bank_list() - encapsulates retreiving bank list
This allows the externs in flash/nor/imp.h to be removed, and
these mechanisms may now be re-used by other flash module code.
Moves the top-level 'flash' command handlers into flash/nor/tcl.c,
with flash/nor/imp.h providing an internal implementation header
to share non-public API components.
Updates the ARM NAND I/O code to look at and update the op
field of arm_nand_data to reflect the last operation performed.
It uses this field to copy the correct code to the target in the
case where the struct is used for reads and writes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Modify the arm_nand_data struct to better support both read and
write operations while using the same struct. An additional
field was added, and initialized, to record the last operation
so that the correct code can be loaded to the working area.
[dbrownell@users.sourceforge.net: merge init patch, tweak GPL note]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Created a new function that handles sending a command and the address
information for pages to a NAND device.
[dbrownell@users.sourceforge.net: tweaked line lengths, name 'oob_only']
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Before we can -I the top-level src/ directory alone, references to
"hello.h" must be updated. This is an internal header, so it does
not need angle brackets.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "s3c24xx_regs.h"
the following form should be used.
#include <flash/nand/s3c24xx_regs.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "ocl.h"
the following form should be used.
#include <flash/nor/ocl.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "nand.h"
the following form should be used.
#include <flash/nand.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "flash.h"
the following form should be used.
#include <flash/flash.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "arm_nandio.h"
the following form should be used.
#include <flash/arm_nandio.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "target.h"
the following form should be used.
#include <target/target.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "mips32.h"
the following form should be used.
#include <target/mips32.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "image.h"
the following form should be used.
#include <target/image.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "embeddedice.h"
the following form should be used.
#include <target/embeddedice.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "avrt.h"
the following form should be used.
#include <target/avrt.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "armv7m.h"
the following form should be used.
#include <target/armv7m.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "armv4_5.h"
the following form should be used.
#include <target/armv4_5.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "arm966e.h"
the following form should be used.
#include <target/arm966e.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "arm7_9_common.h"
the following form should be used.
#include <target/arm7_9_common.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "algorithm.h"
the following form should be used.
#include <target/algorithm.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "jtag.h"
the following form should be used.
#include <jtag/jtag.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "types.h"
the following form should be used.
#include <helper/types.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "time_support.h"
the following form should be used.
#include <helper/time_support.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "membuf.h"
the following form should be used.
#include <helper/membuf.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "log.h"
the following form should be used.
#include <helper/log.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "fileio.h"
the following form should be used.
#include <helper/fileio.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "binarybuffer.h"
the following form should be used.
#include <helper/binarybuffer.h>
The exception is from .c files in the same directory.
Includes the src directory in the search path, so header files may be
migrated from:
#include "foo.h"
to
#include <module/foo.h>
which is more conducive for installation.
Move device argument parsing after check for number of arguments;
otherwise, calling this command without any arguments would access
argv[0] before checking whether it even existed.
Fixed the header file to properly specify the doxygen documentation for the
items defined in it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates the functions in the file to all have doxygen comments
describing what they do.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Created a function for copying code to the working area on
a target. The NAND write and read functions are updated to
include use of this function.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Implementation of the NAND read function for ARM NAND I/O that
includes running a local algorithm on a device to increase the
performance of block reads.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Command upgrading introduced two off-by-one bugs in the flash commands.
This patch fixes the 'flash {protect,erase_sector}' commands to check
that they have been passed the correct number of arguments.
Ammended during commit to fix help text for 'erase_address' too.
Removes hello and foo commands from top-level registration. Instead,
the dummy interface driver and faux flash driver have been augmented
to register these commands as sub-commands.
Adding jim_handler field to command_registration allows removing the
register_jim helper. All command registrations now go through the
register_command{,s}() functions.
Move bulk of for-loop to a new static command helper function.
Adds handle_nand_list_drivers command handler, registered as
'nand drivers'.
Improves command help text and error reporting.
Move variables to point of first use, reducing their scope.
Add driver_name temporary to help arguments be changed later.
Eliminates the useless 'found' variable, changing the code to terminate
the loop immediate and return its success.
After adding support for referencing banks by name, renames
the COMMAND_HELPERs appropriately:
flash_command_get_bank_by_num -> flash_command_get_bank
nand_command_get_device_by_num -> flash_command_get_device
Add get_flash_bank_by_name (and get_nand_device_by_name) helpers
to retrieves struct flash_bank * (struct nand_device *) given a
driver name and an (optional) driver-specific bank index.
These are used to extend flash_command_get_bank_by_num (and
nand_command_get_device_by_num) to allow all flash (nand) commands to
reference defined banks by name, not just by number.
To avoid some code duplication, add the flash/common.[ch] files to hold
functionality common to both types driver. The first two methods are
helpers for the above routines to find a bank specified by a "name" or
"name.index" string. get_flash_name_index() finds the '.index' portion,
while flash_driver_name_matches() performs the string portion matching.
Updates all command parsing of simple "enable" and "disable" arguments.
A few case in the tree use a tri-state or extended arguments, which
cannot use this simple macro.
Simlifies the xscale icache/dcache command handler logic.
Moves definitions for each layer into their own file, eliminating
layering violations in the built-in TCL code. Updates src/Makefile.am
rules to include all files in the final startup.tcl input file, and
others Makefile.am rules to distribute the new files in our packages.
All ARM cores need to provide obsolete FPA registers in their
GDB register dumps. (Even though cores with floating point
support now generally use some version of VFP...)
Clean up that support a bit by sharing the same dummy registers,
and removing the duplicate copies. Eventually we shouldn't need
to export those dummies.
(This makes the ARMv7-M support include the armv4_5 header, and
cleans up related #includes, but doesn't yet use anything from
there except those dummies.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use size_t instead of uint32_t when specifying file sizes. Update all
consumers up through the layers to use size_t when required. These
changes should be safe, but the higher-levels will need to be updated
further to receive the intended benefits (i.e. large file support).
Add error checking for fileio_read and file_write. Previously, all
errors were being silently ignored, so this change might cause some
problems for some people in some cases. However, it gives us the chance
to handle any errors that do occur at higher-levels, rather than burying
our heads in the sand.
Add the 'nand verify' command to perform a dump and fake-write
simultaneously, checking the read bits against those generated by the
write process. Appropriate user documentation for this command has
been added to the user guide as well.
The algorithm presently makes a relatively naive comparison. Some chips
that use ECC may not verify correctly using this implementation, but the
new documentation provides details about this limitation.
This patch eliminates duplicated code in the the NAND 'dump' and 'write'
by using the new static helper functions.
These changes also fix a possible memory leak in nand dump command, in
the case that the dump file failed to open.
Overall, the changes should be functionally equivalent, but the
resulting code will be easier to improve and extend further.
This patch provides helpers APIs that will eliminate duplicated code in
the the NAND 'dump' and 'write' commands by factoring their common code
into static helper functions. These helpers may be useful for creating
new commands, as shown in the final patch to 'verify' flash from a file.
Several previously unreported error conditions now generate messages and
propogate the return codes, such as when the file fails to open and bad
arguments are given. These changes will fix a possible memory leak in
nand dump command, in the case that the dump file failed to open.
Overall, the changes should be functionally equivalent, but the
resulting code will be easier to improve and extend consistently.
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Lots of files still include it, often through needless
duplicate inclusion of "log.h"; sigh.
This cleans up the inclusion graph a bunch, so there are
fewer inclusion paths, but it doesn't change much otherwise.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
downloadable algorithms actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also: "algorithm.h" doesn't need to include "types.h" again;
it already comes from a different header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove the last external user of arm7_9_get_arch_pointers(), and
that annoying downcast utility. Add an is_arm7_9() predicate.
Stop returning specious success codes on various failure paths
in the ARM7/ARM9 commands which used that downcast utility.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The number of command arguments will always be 0 or more, so use
the right type in handlers. This has a cascading effect up through
the layers, but the new COMMAND_HANDLER macros prevented total chaos.
By using CALL_COMMAND_HANDLER, parameters can be reordered, added, or
even removed in inherited signatures, without requiring revisiting
all of the various call sites.
The FLASH_BANK_COMMAND_HANDLER provides an extended command handler
using the __COMMAND_HANDLER macro, whereby changing that macro is
sufficient to update flash handlers with the new signature. It also
enforces uniform style and scope when implementing this handler.
To be more informative (and consistent with flash and pld trees), change
'device' parameter name to 'nand' in NAND source files. This change
eliminates confusing 'device->device->' instance from the code, and
it simplifies the forthcoming command handler patches.
Add 'const' keyword to 'char *' parameters to allow command handlers to
pass constant string arguments. These changes allow the 'args' command
handler to be changed to 'const' in a subsequent patch.
Subsequent patches expect all command handlers to use a uniform
parameter naming scheme. In the entire tree, these two files used
standard 'argv' instead of our non-standard 'args'. This patch opts
to reduces the noise required to unify the command handlers, using
dominant 'args' form.
A future patch may be used to convert us back to the standard argv, but
that requires coordination with all developers to minimize disruptions.
Separates various groups of files to be built in logical succession.
In each layer, the core module (target.c, nand.c, etc.) is built _after_
their helper modules (e.g. image.c, nand_ecc.c) but _before_ any of
their drivers (e.g. arm966e.c, mx3_nand.c).
This allows problems introduced at the bottom of the stack to result
in build failures as soon as possible, as the helpers and core should
wrap portions of them.
Remove useless forward declarations.
Moves command registrations to end of files.
Moves flash structure definitions to end of files.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Remove useless forward declarations.
Moves command registrations to end of files.
Moves flash structure definitions to end of files.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Remove useless forward declarations.
Moves command registrations to end of files.
Moves flash structure definitions to end of files.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Remove useless forward declarations.
Moves command registration to end of file.
Moves flash structure definitions to end of files.
Changes a few references to global flash structure to local refs.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Remove useless forward declarations.
Moves command registrations to end of files.
Moves flash structure definitions to end of files.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Remove useless forward declarations.
Moves command registration to end of files.
Moves flash structure definition to end of files.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Remove useless forward declarations.
Moves command registration to end of file.
Moves flash structure definition to end of file.
Signed-off-by: Zachary T Welch <zw@superlucidity.net>
Removes 'extern' keywords from function prototypes in the flash headers.
Wraps long lines to fit into 80 columns.
Adds multiple inclusion protection for s3c2xx_nand.h.
This patch changes the duration_* API in several ways. First, it
updates the API to use better names. Second, string formatting has
been removed from the API (with its associated malloc). Finally, a
new function added to convert the time into seconds, which can be
used (or formatted) by the caller. This eliminates hidden calls to
malloc that require associated calls to free().
This patch also removes the useless extern keyword from prototypes,
and it eliminates the duration_t typedef (use 'struct duration').
These API also allows proper error checking, as it is possible for
gettimeofday to fail in certain circumstances.
The consumers have all been chased to use this new API as well, as
there were relatively few cases doing this type of measurement.
In most cases, the code performs additional checks for errors, but
the calling code looks much cleaner in every case.
This eliminates redundant code for parsing and retreiving the bank
specified from a script command argument. This patch was written to
replace existing functionality; however, the parsing logic can be
updated later to allow flash commands to accept bank names as well as
their numbers.
didn't turn up earlier. Is everyone still using gcc 3.x? Or is the x86
version of gcc 4.x much more relaxed?
git-svn-id: svn://svn.berlios.de/openocd/trunk@2749 b42882b7-edfa-0310-969c-e2dbd0fdcd60
of a (NOR) flash chip: allow passing "last" as an alias
for the number of the last sector.
Improve several aspects of error checking while we're at it.
From: Johnny Halfmoon <jhalfmoon@milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2746 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch modifies an error message which, in its original state,
I find somewhat unhelpful. So a small hint was added.
Signed-off-by: Johnny Halfmoon <jhalfmoon at milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2738 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Erase logic:
- command invocation
+ treat "nand erase N" (no offset/length) as "erase whole chip N"
+ catch a few more bogus parameter cases, like length == 0 (sigh)
- nand_erase() should be static
- on error
+ say which block failed, and if it was a bad block
+ don't give up after the first error; try to erase the rest
- on success, say which nand device was erased (name isn't unique)
Device list ("nand list"):
- say how many blocks there are
- split summary into two lines
- give example in the docs
Doc tweaks:
- Use @option{...} for DaVinci's supported hardware ECC options
For the record, I've observed that _sometimes_ erasing bad blocks causes
failure reports, and that manufacturer bad block markers aren't always
erasable (even when erasing their blocks doesn't trigger an error report).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2724 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch adds target algorithm support for those flash devices that do not support DQ5 polling. So far they could only be programmed with host algorithm, but this was way too slow.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2682 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Optionally shave time off the armv4_5 run_algorithm() code: let
them terminate using software breakpoints, avoiding roundtrips
to manage hardware ones.
Enable this by using BKPT to terminate execution instead of "branch
to here" loops. Then pass zero as the exit address, except when
running on an ARMv4 core. ARM7TDMI, ARM9TDMI, and derived cores
now set a flag saying they're ARMv4.
Use that mechanism in arm_nandwrite(), for about 3% speedup on a
DaVinci ARM926 core; not huge, but it helps. Some other algorithms
could use this too (mostly flavors of flash operation).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2680 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Abstract the orion_nand_fast_block_write() routine into a separate
routine -- arm_nandwrite() -- so that other ARM cores can reuse it.
Have davinci_nand do so. This faster than byte-at-a-time ops by a
factor of three (!), even given the slowish interactions to support
hardware ECC (1-bit flavor in that test) each 512 bytes; those could
be read more efficiently by on-chip code.
NOTE that until there's a generic "ARM algorithm" structure, this
can't work on newer ARMv6 (like ARM1136) or ARMv7A (like Cortex-A8)
cores, though the downloaded code itself would work just fine there.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2663 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Via code review by Steve Grubb <sgrubb@redhat.com>
Almost innocuous; this is value is checked later, this
check being wrong would make it check stack garbage.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2655 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Via code review by Steve Grubb <sgrubb@redhat.com>
Also minor fixes for the message from "fill": the byte
count is unsigned, not signed; and more importantly,
print the real number of bytes written
git-svn-id: svn://svn.berlios.de/openocd/trunk@2652 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Bugfixes:
* internal osc: it's *12* MHz (not 15 MHz) on _current_ chips
+ except new Tempest parts where it's 16 MHz (and calibrated!)
+ or some old Sandstorm ones, where 15 MHz was valid
* crystal config:
+ read and use the crystal config, don't assume 6 MHz
+ know when that field is 4 bits vs 5
* an RCC2 register may be overriding the original RCC
+ more clock source options
+ bigger dividers
+ fractional dividers on Tempest (NYET handled)
* there's a 30 KHz osc on newer chips (for deep sleep)
* there's a 32768 Hz osc on newer chips (for hibernation)
- Cosmetic
* say "rev A0" not "vA.0", to match vendor docs
* don't always report master clock as an "estimate":
+ give the error bound if it's approximate, like "±30%"
+ else don't say anything
* fix whitespace and caps in some messages
* these are not AT91SAM chips!!
Those clock issues might explain problems sometimes reported when
writing to Stellaris flash banks; they affect write timings.
That 12-vs-15 MHz issue is problematic; there's no consolidated doc
showing which chips (and revs!) have which internal oscillator speed.
It's clear that only older silicon had the faster-and-less-accurate
flavor. What's less clear is which chips are "old" like that.
Lightly tested, on a DustDevil part.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2626 b42882b7-edfa-0310-969c-e2dbd0fdcd60
OpenOCD was able to access only to chips attached to first EMIF
chipselect. This patch fixes chipselect management code and allows
OpenOCD to access to NAND devices attached to any EMIF CS line.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2585 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add flash programming support for NXP LPC1700 cortex_m3 based family
git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix issue when multiple flash chips are connected, eg. x16 x 2 on 32bit mcu bus
git-svn-id: svn://svn.berlios.de/openocd/trunk@2551 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Restore some whitespace that got clobbered by over-aggressive
whitepace eradication patches a while back.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2446 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Warn when people (or scripts) use numeric identifiers for TAPs,
instead of dotted.name values. We want this usage to go away,
so that for example adding more TAPs doesn't cause config scripts
to break because some sequence number changed.
It's been deprecated since late 2008, but putting a warning on
this should help us remove it (say, in June 2010) by helping to
phase out old (ab)usage in config scripts.
Other than in various config files, the only code expecting such
a number was the almost unused str9xpec driver. This code was
changed to use the TAP it was passed, instead of making its own
dubious lookup and ignoring that TAP.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2415 b42882b7-edfa-0310-969c-e2dbd0fdcd60
this fn has something to do with the queue, which it does not as such.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2050 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Remove broken whitespace ... mostly at end of line, but
also in some cases blocks of inappropriate empty lines.
And spell "comamnd" right. :)
git-svn-id: svn://svn.berlios.de/openocd/trunk@1972 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- use continuations to break long lines of variable assignments
- makes these variables more patch-friendly and conform to style guide
git-svn-id: svn://svn.berlios.de/openocd/trunk@1970 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- replaces all calls to target->type->bulk_write_memory.
- add documentation in target_s to warn not to invoke callback directly.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1963 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- replaces all calls to target->type->run_algorithm.
- add documentation in target_s to warn not to invoke callback directly.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1961 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- replaces all calls to target->type->write_memory.
- add documentation in target_s to warn not to invoke callback directly.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1960 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- replaces all calls to target->type->read_memory.
- add documentation in target_s to warn not to invoke callback directly.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1959 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- provides low-level information about each flash API interface,
- gives driver authors some documentation about the driver interface,
- updated extensively from the original patch provided by Duane Ellis.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1942 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Fix a bug that joined us at the last minute, when an efficient
alloca() call got swapped out for a more portable malloc().
Also log one error, to give a clue in case it appears "in the wild".
git-svn-id: svn://svn.berlios.de/openocd/trunk@1907 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update two oddball NAND commands to work with {offset, length}
instead of block numbers, matching the other commands as well
as usage in U-Boot and the Linux-MTD utilities.
Document them accordingly. Update the single in-tree use of
those commands (sheevaplug).
ALSO:
(a) Document the current 2 GByte/chip ceiling for NAND chipsize.
(32 bit offset/length values can't represent 4 GBytes.) Maybe
after the upcoming release, the code can switch to 64-bits.
(b) The "nand check_bad_blocks" should report "bad" blocks. They
are not "invalid" blocks; they're "bad" ones.
(c) Tweak the "nand info" command to handle the "no arguments"
case sanely (show everything, instead of showing garbage) and
not listing the blocksize in hex kbytes (duh).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1904 b42882b7-edfa-0310-969c-e2dbd0fdcd60
NAND support for DaVinci-family drivers, with HW ECC support.
Declare the NAND chip on the DM355 EVM board.
Currently tested on DM355 for Linux interop using the standard
large page (2KB) chip in the EVM socket; "hwecc1" and "hwecc4"
work fine. (Using hwecc4 relies on patches that haven't quite
made it through the Linux-MTD bottlenecks yet.)
Not yet tested: 1-bit on small-page (although it's hard to see
how that could fail); 4-bit on small page (picky layout issues);
the "hwecc_infix" mode (primarily for older boot ROMs; testing
there is blocked on having new bootloader code).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1903 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Remove un-implemented and dubious "nand copy" command.
Doing this efficiently would mean doing the copying on
the target CPU, instead of back and forth through JTAG.
If anyone ever needs this functionality, that's what
they should implement.
Also, update on-line "help" for "nand dump" to display
its two optional flags; and for "nand write" to display
a recently added flag.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1883 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the key command_*() helper functions, fixng the bugs that turned up.
Several of these bugs were from misuse of PRIi64; that's for 64-bit
integers, NOT for "long long" or "u64" (which work best with %lld).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1873 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Add libtoolize step too bootstrap script; creates ltmain.sh script.
- Add AC_PROG_LIBTOOL to configure.in to add libtool support to build.
- Change Makefile.am library rules from static (_a) to libtool (_la).
- Install libopenocd.{la,so,a} in $(libdir); update openocd link rules.
- Extend MAINTAINERCLEANFILES in top-level Makefile.am to remove ltmain.sh.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1695 b42882b7-edfa-0310-969c-e2dbd0fdcd60
already required autoconf 2.59 (circa 2006), so there is no reason to
support versions of automake older than 1.6 (circa 2002).
The first part of this patch upgrades the configure.in script:
1. Use current calling conventions for the AC_INIT and
AM_INIT_AUTOMAKE macros, bringing their usage up-to-date with
the version of autoconf already specified by AC_PREREQ.
2. Add AC_CONFIG_SRCDIR macro, required by new version of AC_INIT.
3. Automatically enable all of automake's warnings except Makefile
portability (which OpenOCD violates by using GNU make's $(wildcard)).
[[ While automake has its own -Werror option, I did not enabled it
due to existing warnings. ]]
4. Add the missing AM_PROG_C_O check, required by the build rules for
openocd.o in src/Makefile.am.
5. Adjust version number to show progress toward the next release.
6. Include a bug reporting e-mail address to direct users to this list.
This patch makes the following adjustments to the Makefile.am files:
1. Update AUTOMAKE_OPTIONS to require automake version 1.6
2. Rewrite all deprecated INCLUDES assignments as AM_CPPFLAGS
3. Clean-up all AM_CPPFLAGS declarations to be patch-friendly.
4. Remove vestigial references to $(all_includes)
5. Remove erroneous references to @CPPFLAGS@ (only use AM_CPPFLAGS)
6. Remove unused -I and -D directives in helper/, flash/, target/
git-svn-id: svn://svn.berlios.de/openocd/trunk@1591 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Spencer Oliver
Roman D
Szymon Modzelewski
Muranaka Masaki
Gianluca Renzi
Freddie Chopin
Andreas Fritiofson
Olivier Schonken
George Harris
Chuen Chou
Salvador Arroyo
Christopher Kilgour
Martin Nowak
Mike Crowe
Mirela Tauciuc
Aurelien Jacobs
Linus Tolke
Mathias K
Simon Qian
Øyvind Harboe
Fredrik Hederstierna
Attila Kinali
Stian Skjelsad
Jonathan Dumaresq
Fujitsu FM3 Application Team
Timo Ketola
Bruno FLEURETTE
Erik Ahlén
rodrigo_l_rosa
Tomas Frydrych
Antonio Borneo
Edgar Grimberg
Clément Burin des Roziers
Andreas Bießmann
Gunnar Henne
Spencer Oliver
Ronny Strutz
Luca Bruno
Stefan Mahr
Freddie Chopin
Damjan Marion
SimonQian
Alexandre Pereira da Silva
Uwe Hermann
Bjarne Steinsbo
Thomas Schmid
Eric Wetzel
Erik Botö
Santeri Salko
Michael Schwingen
Andrew MacIsaac
Paul Richards
Rolf Meeser
Flemming Futtrup
Wookey
David Brownell
Olaf Lüke
Edgar Grimberg
gcembed
Jon Povey
Karl Kurbjun
Tobias Ringström
Daniel Bäder
richard vegh
Bradey Honsinger
Hans Peter Mortensn
Peter Korsgaard
Laurentiu Cocanu
Piotr Esden-Tempski
Dean Glazeski
Zachary T Welch
lementec fabien
Yauheni Kaliuta
oharboe
ntfreak
dbrownell
zwelch
duane
kc8apf