This ensures that we populate the register cache and set target->state.
Some RISC-V changes had upset the balance.
Change-Id: I47fbf8ebd8fe39fa5b752212080f87e3b7e6e5e5
Signed-off-by: Tim Newsome <tim@sifive.com>
We don't correctly write it, so we shouldn't expect it to read back the
same value. Fixes hardware breakpoints on mcontrol triggers.
Change-Id: Ie5e445060ec9c8887af933fd8887e57308330f09
Indicate to the JTAG driver that it does not need
to read and return the DR register value after scanning the
JTAG chain.
riscv_batch_run(), calls jtag_add_dr_scan() to schedule a
DR scan operation. Eventually, this will result in the JTAG
driver performing a JTAG scan to write to or read from DR.
The decision on whether to write to and/or read from DR
register is determined by the second parameter to
jtag_add_dr_scan(), i.e. a "struct scan_field".
Of particular interest here is if
batch->fields[i]->in_value is not NULL, the JTAG developer
must return the DR value collected from the JTAG scan
operation.
When creating the DR scan operation instruction with
riscv_batch_add_dmi_write(), batch->fields[i]->in_value points
to a location in batch->data_in buffer,
meaning batch->field[i]->in_value is not NULL, and the JTAG
developer must therefore read and return the DR value collected.
The returning of the DR value is redundant in a write
operation.
This patch set batch->fields[i]->in_value to NULL to indicate
the DR value need not be returned. This allows the JTAG
developer to optimize away any code associated with returning
the DR value.
Normally, the extra work to return the DR value is negligible.
However, in one usecase it introduces significant delays
In this use case a JTAG driver forwards
all JTAG scan to a server on a network. If the server has to
return the DR value, it has to perform the JTAG scan before
replying to the JTAG driver, and only then the JTAG driver
can send the next JTAG scan operation. However, if there is
no need to return the DR value, the server can
acknowledge the JTAG operation request immediately,thus
signalling to the JTAG driver that it is free to send the next
JTAG scan operation. At the same time of receiving the second
JTAG operation the server will process the original JTAG scan.
This saves time and mitigates network delay. Also, not having
to include the DR value in resulting in smaller reply packet
from server to JTAG driver and save on network traffic.
This doubles download speeds to spike using remote bitbang.
Change-Id: Ibb37c3e32af0cc7006b22b8c4e1f31ed29c21d0f
Signed-off-by: Ooi, Cinly <cinly.ooi@intel.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Ooi, Cinly <cinly.ooi@intel.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Ooi, Cinly <cinly.ooi@intel.com>
It's only used to change what callback events are generated, and there
are none anyway. (That's probably a bug, but since 0.11 is so rare I'm
not going to worry about it.)
Fixes#757.
Change-Id: I5b5df3a9bec927fb0368304229533e2875a83f6b
Signed-off-by: Tim Newsome <tim@sifive.com>
On some boards there is a HW bug: if fp unit is disabled (fs in mstatus
set to 0), accessing any fp register results in a hang (any abstract
command timeouts, untill the board is rebooted).
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: I0c0d1033889f15dcc326c4078bf9cbb5a8558565
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
E.g. the Zve* vector extensions have all the same registers as the full
V extension, but leaves misa.V clear.
Change-Id: Ib08c3612c52bb3a6b074d9431e3396c8f2f0ff27
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Prep work for handling unavailable harts.
Change-Id: I9c00ed4cdad8edeaa5a13fbec7f88f40d8af9028
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Use match field for trigger
The watchpoint cannot capture all data modifications only through the
trigger of ANY SIZE and EQUAL, and an error will occur. This patch
accommodates watchpoints by adding more types of matches
Change-Id: I5c3c908dbd49ca47755b06f5cdbe451be3a81c8b
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Xiang W <wxjstz@126.com>
* Update src/target/riscv/riscv.c
Change-Id: I3670347c4b00bf508373f7cc2f4950cbc09d6e2a
Signed-off-by: Xiang W <wxjstz@126.com>
* Add variable type trigger support
Change-Id: I60922c5f98574040b9a160e2aa0355871a581fe1
Signed-off-by: Xiang W <wxjstz@126.com>
* remove trailing whitespace
Change-Id: I168812e12b459ae3c4b3017c27a9b897e65d9f84
Signed-off-by: Xiang W <wxjstz@126.com>
* update triggers enumerate
Change-Id: I23a66afb0f772934b8911b522d0e4f116917519f
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* target/riscv: Deal with DMI busy in sample_memory_bus_v1()
Change-Id: I810a4c4b7f02cb40ea99b7a500dce23c1bbd9231
Signed-off-by: Tim Newsome <tim@sifive.com>
* Comment code more clearly.
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Remove extra tab
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* target/riscv Fix dm->current_hartid corruption on hartsellen discovery
Change-Id: Iec969df2675b608365eda2c3a83a4185752430f2
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
* target/riscv Ensure HART_INDEX_DIRTY does not have side effects
Change-Id: Ie89c94d97cd4f15c1be0327fddff75beea6ae027
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
- Fix the declaration of riscv command 'set_mem_access'.
- Remove non existing riscv command 'set_scratch_ram'.
- Add riscv commands 'info', 'reset_delays'; copy the description
from the 'help' text.
- Don't add riscv commands 'set_prefer_sba' and 'test_sba_config_reg'
as they are marked as deprecated.
- Ensure that 'test_sba_config_reg' prints a deprecation warning
when used.
Change-Id: I39dc3aec4e7f13b69ac19685f1b593790acdde83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7268
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
* target/riscv: Correctly set target->state in deassert_reset
This bug didn't lead to problems, but it would with some upcoming
changes.
Change-Id: I552acbae9977150c4c9e573f8852033bc80fcebb
Signed-off-by: Tim Newsome <tim@sifive.com>
* Keep debug_reason in sync with state
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* [riscv] step operation handler should respect handle_breakpoints parameter
When step operation is requested the OpenOCD frontend (like gdb server
or TCL server) has an option to control how existing breakpoints are
handled upon step.
Some OpenOCD frontends (like gdbserver) may choose to disable special
handling of existing breakpoints - thus handle_breakpoints is set to 0,
while others (like TCL server) expect target handler to temporary
disable the matching breakpoint to allow the step operation to complete
successfully.
In the current implementation handle_breakpoints parameter was ignored
by target-specific handler. Thus, the following sequence of commands:
```
halt
bp <current_pc> 4
step
```
Resulted in *step* operation to not change PC because of bp match.
This commit addresses this issue.
* Adjusted calls to logging facilities (addressed review comments)
Co-authored-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
Signed-off-by: Anatoly Parshintsev <114445139+aap-sc@users.noreply.github.com>
Co-authored-by: Tim Newsome <tim@sifive.com>
* Properly track selecting multiple harts at once.
use_hasel is a bit of a hack.
Change-Id: Ia589ebc16bca32038d915df9988361b88e940917
Signed-off-by: Tim Newsome <tim@sifive.com>
* Clarifying comment.
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
* Rename set_hartsel to set_dmcontrol_hartsel
Change-Id: Iab28531281aa6fc604ec7d34974ed444ea9ea850
* Make set_dmcontrol_hartsel() more idiomatic.
Change-Id: I56a885043c515359e33b9c8a03aed637c81d1486
* Use constant for multiple harts instead of -1.
Change-Id: Iefeaf74202f2b4918d21f15f7ff7ca514175b8fb
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Also add an early exit for if any harts are unavailable.
Change-Id: I0875d4d213c9faf87b219d8d57e440881366c8f8
Signed-off-by: Tim Newsome <tim@sifive.com>
This was used to track which hart a given operation must apply to. But
we already have a target associated with each operation, and from there
we can find the desired hart id. dm013_info_t already tracks
current_hartid (meaning which hart ID is currently selected by the DM).
This makes the code simpler to understand. Also it turns out we don't
need to make sure the correct hart ID is currently selected because
there are only a few real entry points.
Change-Id: Ibe8d5e156523397f245edd6ec0a5df3239b717bf
Signed-off-by: Tim Newsome <tim@sifive.com>
According to RISC-V External Debug Support Version 0.13.2 (paragraph
3.12.6), cmderr field contains a valid value only if busy is 0, so it is
incorrect to analize it on timeout.
Scan-build reports:
Logic error: Uninitialized argument value
riscv.c:2688 2nd function call argument is an uninitialized value
This is a real error cause by running the command "riscv
authdata_write" without arguments. In such case 'value' is not
initialized and is passed to and used by r->authdata_write().
Reorganize the code to:
- detect the correct amount or command's arguments;
- drop the LOG_ERROR() on ERROR_COMMAND_SYNTAX_ERROR;
- drop the 'else' after 'return'.
Change-Id: I62e031220593b8308bc674b753e15d16d4c5c9ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7210
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Scan-build reports:
Logic error: Result of operation is garbage or undefined
riscv.c:1614 The result of the left shift is undefined due
to shifting by '4294967281', which is greater or
equal to the width of type 'target_addr_t'
This is a false warning due to clang that considers the impossible
case of 32 bits hart (xlen = 32) in SATP_MODE_SV48 mode
(info->va_bits = 48).
Under such case:
riscv.c:1614 ... ((target_addr_t)1 << (xlen - (info->va_bits - 1))) ...
the shift amount wraps around the unsigned type and assumes the
value 4294967281 (0xfffffff1).
Use assert() to prevent clang from complaining.
Change-Id: I08fdd2a806c350d061641e28cf15a51b397db099
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7209
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead nested assignment
riscv.c:459 Although the value stored to 'ir_user4_raw' is
used in the enclosing expression, the value is
never actually read from 'ir_user4_raw'
This is caused by the value reassigned in 'ir_user4_raw':
riscv.c:459 ir_user4[3] = (uint8_t)(ir_user4_raw >>= 8);
but never used.
Drop the DIY conversion in favor of h_u32_to_le() that does not
reassign the input value.
Change-Id: Ifad29f4c46d4a2d0a2f5a5c4104d768cc3db2794
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7208
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead assignment
riscv.c:716 Value stored to 'result' is never read
Remove the initialization of variable 'result'.
Change-Id: Ied67bb4fcfa5bace186522074247ead43a5d5cd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7207
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead initialization
riscv-013.c:2362 Value stored to 'control' during its
initialization is never read
Remove the initialization of variable 'control'.
Change-Id: I548f8175530b9a2aa4c1788549d6467bf9824584
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7206
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build complains about variable 'sbcs_orig' that can be used
not initialized.
Logic error: Assigned value is garbage or undefined
riscv-013.c:4468 Assigned value is garbage or undefined
This is caused by not checking the return value of the call
riscv-013.c:4466 dmi_read(target, &sbcs_orig, DM_SBCS);
In fact when dmi_read() returns error, the variable 'sbcs_orig' is
not assigned.
Check the returned value.
Change-Id: Ia9032a0229aa243138f95f4e13f765726a4ceae9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7205
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Move the existing comments to the static declarations.
Change-Id: Idf208e3fda4b3f8df789553cf03ebf5f20d811bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7170
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: Ie3bd17535c8cb2a0fec5d3bedfe7de3e0a702613
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7166
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Otherwise OpenOCD simply doesn't work without giving any indication why.
Change-Id: I21703fc1a0d9bed2f59da95f8a8395fe139484a4
Signed-off-by: Tim Newsome <tim@sifive.com>
* Don't read dmcontrol to set hartsel
We already know what dmcontrol should be. This addresses a long-standing
TODO. In a toy test, this reduced the number of scans by 10+%. (Most of
those are probably in poll(), so don't actually affect perceived
performance.)
Change-Id: I18e5ca391f0f5fb35f30d44dfef834e5a66aee20
Signed-off-by: Tim Newsome <tim@sifive.com>
* Make code easier to read
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Hopefully this will be the final version.
Change-Id: Ib2f8cd6f613c5e0f8e8bf7a16c3edbf2d9b439b2
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
See https://github.com/riscv/riscv-opcodes/pull/139
Change-Id: I77ae5ab369e6cde26ad44d177dcae38c0fbe08ef
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
Now we get the license comment on the first line, which is required.
Change-Id: I54414db3c89ee6027e159ce9348459bc923b8595
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Tim Newsome <tim@sifive.com>
This one doesn't have the license in there, which means now it's
acceptable to GPLv2 again.
See https://github.com/riscv/riscv-openocd/pull/711
Change-Id: I8ba27801172ffa955470d2627fa656cad282ee99
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7087
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If range's upper bound was equal to 2^64 or the range was wrapping around 0
(which is perfectly legal), writes were not performed due to riscv_addr_t
overflow.
Make the main RISC-V structure more compliant with OpenOCD coding style.
Other typedefs remains as is.
Change-Id: I5657ad28fea8108fd66ab27b2dfe1c868dc5805b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6998
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
SPDX tag is replacing the FSF boilerplate.
For files that have both, remove the FSF boilerplate and keep only
the SPDX tag.
Change-Id: I04c4764d13d4ca92453f30ed16aeae53cd4c3fc8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7057
Tested-by: jenkins
Add the SPDX tag to makefiles, configuration scripts and tcl files
present in the folders under src/
Change-Id: I1e4552aafe46ef4893d510da9d732c5f181784a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7051
Tested-by: jenkins
This one doesn't have the license in there, which means now it's
acceptable to GPLv2 again.
Change-Id: I8ba27801172ffa955470d2627fa656cad282ee99
Signed-off-by: Tim Newsome <tim@sifive.com>
This gets us the new license header, which was requested upstream.
Change-Id: I992b4f3bb230edb9f281e2278dd41c712098ed4c
Signed-off-by: Tim Newsome <tim@sifive.com>
These enum values are useful for the arch level semihosting call handlers.
Currently riscv uses them, we also need similar return codes for the xtensa.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I8f63749cc203c59b07862f33edf3c393cd7e33a9
Reviewed-on: https://review.openocd.org/c/openocd/+/7039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The segfault could be triggered if:
- At least one target failed to get examined (therefore does not have the
register cache set up yet),
- and "reset" TCL command was issued, which internally tries to
invalidate the register cache.
Minor cleanup: "registers_initialized" member removed from riscv_info_t
because it is not used anywhere.
Change-Id: I6288c0d4343ef6a330fb2a6b49d388e7eafa32a2
Signed-off-by: Jan Matyas <matyas@codasip.com>
* Update debug_defines from the spec.
Now it includes constants for field values, so use them instead of
duplicating that here.
Change-Id: I2fca6e89f25123c39d4bf483b8244e47aefb0f88
* Remove unused #defines
Change-Id: Id20351851c9ed2c3aa82ccf8c04b604bef11692a
* Use debug spec constants in a few more places
Change-Id: Ic4578729c89e3c6a26a72772e1635c5345bd6a52
Signed-off-by: Tim Newsome <tim@sifive.com>
* Use macros for trigger action types.
Which were added with the very latest debug_defines.h.
Change-Id: I47f73e11d2ec529c720f2e1df05f7b0d3026e43a
Signed-off-by: Tim Newsome <tim@sifive.com>
* Change set_haltgroup() to more general set_group()
Change-Id: Ib91a252ac63604e54b756f70c549ccd47241fd10
Signed-off-by: Tim Newsome <tim@sifive.com>
* Properly use enum.
Change-Id: I0edef6053fac388db38a22fe7557623fa93ec705
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* Style changes suggested in review.
Change-Id: I29e83d3dbef09cb971ec0355aff733191a6e4679
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
* riscv: Add a option to specify the JTAG TAP IR used to access the bscan tunnel.
Change-Id: Ice8798823313e2177e75473e62b06e7da74bbba2
Signed-off-by: Charles Papon <charles.papon.90@gmail.com>
* risc-v: Add litex doc about the set_bscan_tunnel_ir command
Change-Id: I1237213f32886d20fc7d60d5ca1e2124953eaeda
Signed-off-by: Dolu1990 <charles.papon.90@gmail.com>
* risc-v: remove tunnel ir length assert when ir is set by the user
Change-Id: I2b33fc6205f37461ff1bd15601b460a2467ea32b
Signed-off-by: Dolu1990 <charles.papon.90@gmail.com>
* Open riscv: Add a option to specify the JTAG TAP tunnel IR
Typo
Co-authored-by: Tim Newsome <tim@sifive.com>
* riscv: Add a option to specify the JTAG TAP tunnel IR
typo
Co-authored-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Tim Newsome <tim@sifive.com>
* Fix checkpatch workflow: ignore changes in .github/
Ignore changes in .github/ directory when running checkpatch.
Checkpatch emits false alarms on substrings "CC:" found in *.yml
workflow files, apparently thinking it is a "Cc:" signature in
commit message.
Change-Id: Id977d5a8838797e4676758066af4825651c41a87
* Fix: Set proper debug_reason in deassert_reset()
The issue was visible for example when user's .cfg file ended
with "reset halt" command:
In such case, the hart would remain halted but the debug_reason would not be
updated and may retain an incorrect value, e.g. DBG_REASON_NOTHALTED.
In such cases, gdb_last_signal() would provide an incorrect reply to GDB.
Change-Id: Ie6f050295fb5cbe9db38b189c4bc385662acf5b4
Signed-off-by: Jan Matyas <matyas@codasip.com>
* Fix checkpatch workflow: add 'apt-get update'
Change-Id: Ic5843ec86d16a187d01970a3253caade3d13b7ab
Signed-off-by: Jan Matyas <matyas@codasip.com>
The 'set' variable name suggests a boolean data type which determines
whether a breakpoint (or watchpoint) is active. However, it is also
used to store the number of the breakpoint.
This encoding leads to inconsistent value assignments: boolean and
integer values are mixed. Also, associated hardware comparator
numbers, which are usually numbered from 0, cannot be used directly.
An additional offset is required to store the comparator numbers.
In order to make the code more readable and the value assignment more
consistent, change the variable name to 'is_set', its data type to 'bool'
and introduce a dedicated variable for the break-/watchpoint
number.
In order to make the review easier, the data types of various related
variables (e.g. number of breakpoints) are not changed.
While at it, fix a few coding style issues.
Change-Id: I2193f5639247cce6b80580d4c1c6afee916aeb82
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6319
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/nor/atsame5: add LAN9255 devices
Support Microchip LAN9255 devices with embedded SAME53J MCU.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Change-Id: Ia811c593bf7cf73e588d32873c68eb67c6fafad7
Reviewed-on: https://review.openocd.org/c/openocd/+/6811
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: Add EVB-LAN9255 config
Config for EVB-LAN9255, tested using Atmel-ICE debugger on J10
connector.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Change-Id: I8bcf779e9363499a98aa0b7d10819c53da6a19e7
Reviewed-on: https://review.openocd.org/c/openocd/+/6812
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* aarch64: support for aarch32 ARM_MODE_UND
Fix:
unrecognized psr mode: 0x1b
cannot read system control register in this mode: (UNRECOGNIZED : 0x1b)
Change-Id: I4dc3e72f90d57e52c0fe63cb59a7529a398757b3
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: Ifa5d21ae97492fde9e8c79ee7d99d8a2a871b1b5
Reviewed-on: https://review.openocd.org/c/openocd/+/6808
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Combine register lists of smp targets.
This is helpful when you want to pretend to gdb that your heterogeneous
multicore system is homogeneous, because gdb cannot handle heterogeneous
systems. This won't always works, but works fine if e.g. one of the
cores has an FPU while the other does not. (Specifically, HiFive
Unleashed has 1 core with no FPU, plus 4 cores with an FPU.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I05ff4c28646778fbc00327bc510be064bfe6c9f0
Reviewed-on: https://review.openocd.org/c/openocd/+/6362
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* semihosting: use open mode flags from GDB, not from sys/stat.h
Values defined in sys/stat.h are not guaranteed to match
the constants defined by the GDB remote protocol, which are defined in
https://sourceware.org/gdb/onlinedocs/gdb/Open-Flags.html#Open-Flags.
On my local system (Manjaro 21.2.1 x86_64), for example, O_TRUNC is
defined as 0x40, whereas GDB requires it to be 0x400,
causing all "w" file open modes to misbehave.
This patch has been tested with STM32F446.
Change-Id: Ifb2c740fd689e71d6f1a4bde1edaecd76fdca910
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* semihosting: User defined operation, Tcl command exec on host
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/smp: use a struct list_head to hold the smp targets
Instead of reinventing a simply linked list, reuse the list helper
for the list of targets in a smp cluster.
Using the existing helper, that implements a double linked list,
makes trivial going through the list in reverse order.
Change-Id: Ib36ad2955f15cd2a601b0b9e36ca6d948b12d00f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6783
Tested-by: jenkins
* helper/list: add list_for_each_entry_direction()
Use a bool flag to specify if the list should be forward or
backward iterated.
Change-Id: Ied19d049f46cdcb7f50137d459cc7c02014526bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6784
Tested-by: jenkins
* target/riscv: revive 'riscv resume_order'
This functionality was lost in [1], which was merged as commit
615709d140 ("Upstream a whole host of RISC-V changes.").
Now it works as expected again.
Add convenience macro foreach_smp_target_direction().
Link: [1] https://github.com/riscv/riscv-openocd/pull/567
Change-Id: I1545fa6b45b8a07e27c8ff9dcdcfa2fc4f950cd1
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6785
Tested-by: jenkins
* doxygen: fix some function prototype description
Change-Id: I49311a643ea73143839d2f6bde976cfd76f8c67f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6830
Tested-by: jenkins
* Cadence virtual debug interface (vdebug) integration
Change-Id: I1bc105b3addc3f34161c2356c482ff3011e3f2cc
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6097
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: Include thread name as XML attribute
Explicitly providing a thread name in the "thread" element produces
better thread visualizations in downstream tools like IDEs.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I102c14ddb8b87757fa474de8e3a3f6a1cfe10d98
Reviewed-on: https://review.openocd.org/c/openocd/+/6828
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix small memory leak.
See https://github.com/riscv/riscv-openocd/pull/672
Change-Id: Ia11ab9bcf860f770ea64ad867102c74b898f6b66
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6831
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* server: remove remaining crust from dropped eCos code
Commit 39650e2273 ("ecosboard: delete bit-rotted eCos code") has
removed eCos code but has left some empty function that was used
during non-eCos build to replace eCos mutex.
Drop the functions and the file that contain them.
Change-Id: I31bc0237ea699c11bd70921660f960ee406ffa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6835
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: threadx: Add hla_target support for ThreadX
Tested with an AZ3166 dev board (which uses the STM32F412ZGT6) running
the Azure RTOS ThreadX demonstration system.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I44c8f7701d9f1aaa872274166321cd7d34fb1855
Reviewed-on: https://review.openocd.org/c/openocd/+/6829
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* .gitmodules: switch away from repo.or.cz
The host repo.or.cz is often offline, creating issues for cloning
and building OpenOCD from scratch.
Already 'jimtcl' developer has dropped repo.or.cz, triggering the
OpenOCD commit 861e75f54e ("jimtcl: switch to github").
Change also the link of the remaining submodules 'git2cl' and
'libjaylink' to their respective main repository.
Change-Id: Ib513237427635359ce36a480a8f2060e2fb12ba4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6834
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
* flash/nor/stm32f2x: Fix erase of bank 2 sectors
This commit corrects the erase function for stm32f2x when dealing with
sectors in bank 2, for STM32F42x/43x devices with 1MB flash.
On STM32F42x/43x with 1MB flash in dual bank configuration, the sector
numbering is not consecutive. The last sector in bank 1 is number 7, and
the first sector in bank 2 is number 12.
The sector indices used by openocd, however, _are_ consecutive (0 to 15
in this case). The arguments "first" and "last" to stm32x_erase() are of
this type, and so the logic surrounding sector numbers needed to be
corrected.
Since the two banks in dual bank mode have the same number of sectors, a
sector index in bank 2 is larger than or equal to half the total number
of sectors.
Change-Id: I15260f8a86d9002769a1ae1c40ebdf62142dae18
Signed-off-by: Simon Johansson <ampleyfly@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6810
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* target/cortex_m: fix target_to_cm() helper
The third parameter of container_of() should point to the same member
as target->arch_info points to, struct arm.
It worked just because struct arm is the first member in
struct armv7m_common.
If you move arm member from the first place, OpenOCD fails heavily.
Change-Id: I0c0a5221490945563e17a0a34d99a603f1d6c2ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6749
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/armv7m,cortex_m: introduce checked arch_info cast routines
target_to_armv7m() and target_to_cm() do not match the magic number
so they are not suitable for use outside of target driver code.
Add checked versions of pointer getters. Match the magic number
to ensure the returned value points to struct of the correct type.
Change-Id: If90ef7e969ef04f0f2103e0da29dcbe8e1ac1c0d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6750
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/cortex_m: add Cortex-M part number getter
The getter checks the magic numbers in arch_info to detect eventual
type mismatch.
Change-Id: I61134b05310a97ae9831517d0516c7b4240d35a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6751
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* flash/nor/stm32xx: fix segfault accessing Cortex-M part number
Some of STM32 flash drivers read Cortex-M part number from
cortex_m->core_info.
In corner cases the core_info pointer was observed uninitialised
even if target_was_examined() returned true. See also [1]
Use the new and safe helper to get Cortex-M part number.
While on it switch also target_to_cm()/target_to_armv7m() to the safe
versions. This prevents a crash when the flash bank is misconfigured
with non-Cortex-M target.
Add missing checks for target_was_examined() to flash probes.
[1] 6545: fix crash in case cortex_m->core_info is not set
https://review.openocd.org/c/openocd/+/6545
Change-Id: If2471af74ebfe22f14442f48ae109b2e1bb5fa3b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: f5898bd93f (flash/stm32fxx.c: do not read CPUID as this info is stored in cortex_m_common)
Reviewed-on: https://review.openocd.org/c/openocd/+/6752
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* cpld: altera-epm240: Add additional IDCODEs
This adds some additional IDCODEs from the datasheet. It also adds
support for customizing the tap name.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I7cda10b92c229b61836c12cd9ca410de358ede2e
Reviewed-on: https://review.openocd.org/c/openocd/+/6846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cpld: altera-epm240: Increase adapter speed
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: Add support for ls1088a
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: ls1088a: Add service processor
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* board: Add NXP LS1088ARDB
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: fix double free
Commit 6541233aa7 ("Combine register lists of smp targets.")
unconditionally assigns the output pointers of the function
smp_reg_list_noread(), even if the function fails and returns
error.
This causes a double free from the caller, that has assigned NULL
to the pointers to simplify the error handling.
Use local variables in smp_reg_list_noread() and assign the output
pointers only on success.
Change-Id: Ic0fd2f26520566cf322f0190780e15637c01cfae
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6852
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* gdb_server: check target examined while combining reg list
Commit 6541233aa7 ("Combine register lists of smp targets.")
assumes that all the targets in the SMP cluster are already
examined and unconditionally call target_get_gdb_reg_list_noread()
that will in turn return error if the target is not examined yet.
Skip targets not examined yet.
Add an additional check in case the register list cannot be built,
e.g. because no target in the SMP cluster is examined. This should
never happen, but it's better to play safe.
Change-Id: I8609815c3d5144790fb05a870cb0c931540aef8a
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6853
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* flash/stm32l4x: fix maybe-uninitialized compiler error
using gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0 we get:
error: ‘retval’ may be used uninitialized in this function
fixes: 13cd75b6ec (flash/nor/stm32xx: fix segfault accessing Cortex-M part number)
Change-Id: I897c40c5d2233f50a5385d251ebfa536023e5cf7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix build.
Change-Id: Ia60246246dd859d75659a43d1c59588dbb274d46
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Co-authored-by: Julien Massot <julien.massot@iot.bzh>
Co-authored-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Co-authored-by: Zoltán Dudás <zedudi@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Jacek Wuwer <jacekmw8@gmail.com>
Co-authored-by: Ben McMorran <bemcmorr@microsoft.com>
Co-authored-by: Simon Johansson <ampleyfly@gmail.com>
Co-authored-by: Tomas Vanek <vanekt@fbl.cz>
Co-authored-by: Sean Anderson <sean.anderson@seco.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This functionality was lost in [1], which was merged as commit
615709d140 ("Upstream a whole host of RISC-V changes.").
Now it works as expected again.
Add convenience macro foreach_smp_target_direction().
Link: [1] https://github.com/riscv/riscv-openocd/pull/567
Change-Id: I1545fa6b45b8a07e27c8ff9dcdcfa2fc4f950cd1
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6785
Tested-by: jenkins
Instead of reinventing a simply linked list, reuse the list helper
for the list of targets in a smp cluster.
Using the existing helper, that implements a double linked list,
makes trivial going through the list in reverse order.
Change-Id: Ib36ad2955f15cd2a601b0b9e36ca6d948b12d00f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6783
Tested-by: jenkins
Continuation of the previous patch. There are two more cases
when progbuf cache in OpenOCD shall be invalidated:
- When OpenOCD resets the debug module undergoes reset (dmactive=0),
e.g. during target examination
- When the user manually performs that very same operation
(via riscv dmi_write)
Change-Id: I53f8f08250eeedcbd55ab4361d5665370b063680
Signed-off-by: Jan Matyas <matyas@codasip.com>
This commit relates to progbuf cache,
implemented in https://github.com/riscv/riscv-openocd/pull/381
Make sure the cache gets invalidated when the progbuf
contents change via other means. I've identified two
such cases where the invalidation is required:
1) When the user manually tinkers with the progbuf registers
(TCL command "riscv dmi_write")
2) When program buffer is used as a scratch memory
(scratch_write64())
Change-Id: Ie7ffb0fccda63297de894ab919d09082ea21cfae
Signed-off-by: Jan Matyas <matyas@codasip.com>
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This replaces a static array with 8 bytes per register. When there are
vector registers larger than 8 bytes, they would end up clobbering each
other's values. I can't believe I didn't catch this earlier.
See https://github.com/riscv/riscv-openocd/pull/658
Change-Id: I9df4eaf05617a2c8df3140fff9fe53f61ab2b261
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6775
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Standard C library free() allows NULL pointer as a parameter.
Change target_free_working_area() to conform this convention.
Remove NULL pointer tests before target_free_working_area() calls.
While on it add missing setting pointer to NULL after target_free_working_area().
Change-Id: I7c692ab04a9933398ba5bc614723ad0bdecb87b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6712
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Deal with halt race.
What could happen:
1. hart 1 halts due to a breakpoint
2. OpenOCD polls and notices hart 1 has halted.
3. hart 0 halts because it is in a halt group with halt 1
4. OpenOCD decides to halt hart 0 also.
5. OpenOCD discovers hart 0 is already halted, and doesn't update the
debug reason.
In that case OpenOCD would tell gdb that hart 0 halted, while the
interesting event is that hart 1 halted.
Fix this by updating the debug reason when we discover a hart is already
halted when we try to halt it.
This race was exposed in the Sv* address translation tests, but the bug
has nothing to do with address translation.
Change-Id: I59d871e8545bd644bf42581266f15234b93e9900
Signed-off-by: Tim Newsome <tim@sifive.com>
* Comment set_debug_reason
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
Co-authored-by: Jan Matyas <50193733+JanMatCodasip@users.noreply.github.com>
I missed this when I first add mcontrol6 support.
https://github.com/riscv/riscv-openocd/pull/648
Change-Id: I1a2706c7ea3a6757ed5083091cd2c764a8b0267c
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6684
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The main intention is to get access to some of the CSRs
that were so far unknown to OpenOCD (tinfo, mcountinhibit, ...).
https://github.com/riscv/riscv-openocd/pull/659
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I824fdb558d5c1f73432b0f56f3b0b4d865eceeba
Reviewed-on: https://review.openocd.org/c/openocd/+/6682
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This functionality was lost in #567. Now it works as expected again.
Change-Id: I11a36e076867c0268034ceee763e28b2d4e6ff0f
Signed-off-by: Tim Newsome <tim@sifive.com>
This replaces a static array with 8 bytes per register. When there are
vector registers larger than 8 bytes, they would end up clobbering each
other's values. I can't believe I didn't catch this earlier.
Change-Id: I9df4eaf05617a2c8df3140fff9fe53f61ab2b261
Signed-off-by: Tim Newsome <tim@sifive.com>
This causes trouble if you disconnect/reconnect gdb, because in that
case a halt is issued again. (It probably would be possible to run into
this problem in other ways as well.)
Change-Id: Id5815f9d1dc2c2dd627770e001c03874a307c279
Signed-off-by: Tim Newsome <tim@sifive.com>
This makes things work as expected when OpenOCD disconnects and then
connects again. (This became a problem in #645, which started using the
cache.)
Change-Id: I764e5b410a1a68ca47d2ec39968085618ee363c2
Signed-off-by: Tim Newsome <tim@sifive.com>
This primarily contains the large upstreaming of RISC-V changes, so lots
more RISC-V changes than usual.
Conflicts:
src/target/riscv/opcodes.h
src/target/riscv/riscv-011.c
src/target/riscv/riscv-013.c
src/target/riscv/riscv.c
src/target/riscv/riscv.h
Change-Id: I1145dad538a5470ad209848572e6b0f560b671e9
Signed-off-by: Tim Newsome <tim@sifive.com>
Doxygen cannot resolve the path of the files in folder contrib.
Use a path relative to current folder, as done in other files.
Change-Id: If39b416ed422b4854dd108777fa32dd4c809450a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6635
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Made no attempt to separate this out into reviewable chunks, since this
is all RISC-V-specific code developed at
https://github.com/riscv/riscv-openocd
Memory sample and repeat read functionality was left out of this change
since it requires some target-independent changes that I'll upstream
some other time.
Change-Id: I92917c86d549c232cbf36ffbfefc93331c05accd
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6529
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Properly handle held-in-reset targets.
1. Let OpenOCD continue into some pre-existing code that will periodically
call examine() until it passes.
2. Fix crash in riscv_openocd_poll()
When SMP is configured, it's not guaranteed that all targets have been
examine()d when poll is called on one of them.
Change-Id: Ic6c1d217dc766ea69b67bb2e9a4898e37ee94927
Signed-off-by: Tim Newsome <tim@sifive.com>
* Actually poll for examine at least every 5s.
That's what the comment says the code is trying to do.
Change-Id: I34ff909a98f8aebb3c514e0f3ee403be7699c094
Signed-off-by: Tim Newsome <tim@sifive.com>
* Compact this error message a bit.
Reduces clutter when some targets haven't been properly examined yet.
Change-Id: Id865f191f0fbb48abece8b8558cc9fa2041a26df
Signed-off-by: Tim Newsome <tim@sifive.com>
Broken by #645. It probably broke some other uses as well, but it was
reported (and easy to reproduce) as an issue with flashing.
Change-Id: Ic1b579c1361442479ced14156102ce68ab232396
Signed-off-by: Tim Newsome <tim@sifive.com>
The header files under src/helper/ can currently be included with
either
#include <bits.h>
or
#include <helper/bits.h>
This is because we specify both "src/" and "src/helper/" directories
as include directories. Some files name under "src/helper/", such as
types.h, log.h, and util.h are too generic and could be ambiguous
depending on the search path.
This commit remove "src/helper/" from our include dir and make C files
include explicitly.
Change-Id: I38fc9b96ba01a513d4a72757d40007e21b502f25
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6507
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* WIP on register caching.
So we don't have to save/restore S0 all the time.
Change-Id: I9d83a24dbd92a325213f2b25eebc9ede9dca2868
* Seems to work for RV32.
Change-Id: Ide620faa5dfef4f39c3146e094787ea28d041327
* Use caching everywhere.
Change-Id: I0de249437589e1f49811f34c12726528c045c74f
* Getting closer...
Change-Id: I532455f1e416723b79eecc7d33ec6407ccb8e33c
* All spike tests pass again.
Running all tests now takes 2m54s compared to 3m0s. That's probably not
the thing to measure, since the goal is to improve interactive
performance, while the tests do all kinds of other stuff (like sleep,
and start spike, etc.).
Change-Id: Ic7d944454a64b2baf6e6028debb4a1ba896834d8
* Save s0/s1 during examine.
Change-Id: I4795180e3b04d01433a11d4a0ccb38c35074cc44
Signed-off-by: Tim Newsome <tim@sifive.com>
* Check flush registers result.
Change-Id: I8350c4198cb41881e1143816698aed677a312111
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix upstream style regression.
Change-Id: I4cc7034151ba62fa51aea77e44b0cad9b9b97876
Signed-off-by: Tim Newsome <tim@sifive.com>
Patch generated automatically through the new checkpatch with
flags "--types COMPARISON_TO_NULL --fix-inplace".
This only fixes the comparisons
if (symbol == NULL)
if (symbol != NULL)
The case of NULL on the left side of the comparison is not tested.
Some automatic fix is incorrect and has been massaged by hands:
- if (*psig == NULL)
+ if (*!psig)
changed as
+ if (!*psig)
Change-Id: If4a1e2b4e547e223532e8e3d9da89bf9cb382ce6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6351
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
Expose them in the virtual priv register, and set them on mcontrol6
hardware triggers. I have no good way to test this right now, so it's
all untested. But this change doesn't break anything, at least.
Change-Id: I0343a6169a0b2b1f0cc0abf687c6bdc560d99b1b
Signed-off-by: Tim Newsome <tim@sifive.com>
Fix the remaining Yoda conditions, detected by checkpatch but not
fixed automatically.
While there, apply minor style changes.
Change-Id: I6e1978b89c4d56a20aceaeb2b52968eb6384432a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6356
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
* cortex_m: use unsigned int for FPB and DWT quantifiers
related quantifiers are:
- fp_num_lit
- fp_num_code
- dwt_num_comp
- dwt_comp_available
Change-Id: I07dec2d4aa21bc0e580be0d9fd0a6809f876c2a8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6185
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* telnet: allow hiding selected commands during auto-completion
We have TCL procedure and commands that we do not want to show in
the list of auto-completion. E.g. TCL wrappers for deprecated
commands, internal procedures that are not supposed to be exposed
to user, or even commands that the user decides to hide.
Create a TCL procedure to be called by telnet auto-complete code
in place of the hard-coded TCL command. The procedure will run the
same command and will filter-out the unwanted command names.
Initialize the list of commands to be filtered-out with the name
of the TCL procedure above, as it is considered as internal.
Change-Id: I2d83bbf8194502368c589c85cccb617e69128c69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6194
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* telnet/auto-complete: hide deprecated and internal commands
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* startup.tcl: prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl: [1/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl: [2/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
* tcl: [3/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/stm8: Make 'stm8_command_handlers' static
Change-Id: I5237a8f2a1ecba9383672e37bd56f8ccd17598b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6200
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: Change 'authdata_read' output
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* Enable adapter "Bus Pirate" by default.
The Bus Pirate is now listed in the "OpenOCD configuration summary" too.
Change-Id: Ieb7bf9134af456ebe9803f3108a243204fb2a62d
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/5637
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* coding-style: additional style for C code
To improve readability and to push more uniform code style.
Prefer 'if (false) {...}' for unused code so it get checked by the
compiler.
Define preferred indentation for 'switch' statement.
Require balanced brackets in 'if/else'.
Report the max line length.
Report the formatting strings for stdint/inttypes types.
Report the type 'target_addr_t'.
Prefer 'unsigned int' to 'unsigned'.
Change-Id: I0192a4ed298f6c6c432764fdd156cffd4b13fc89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6203
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
* Add IPDBG JtagHost functionality to OpenOCD
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/nor/xcf: Do not use 'Yoda conditions'
Change-Id: I17308f5237338ce468e5b86289a0634429deaaa9
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6201
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: add armv8m special registers
Change-Id: I1942f375a5f4282ad1fe4a2ff3b8f3cbc64d8f7f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6016
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: Add support for Zephyr RTOS
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/armv7m.h: [style] replace tab with space between variable type and name
Change-Id: I9740c25857295a2a655d3046322a3f23f0ee7f78
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6230
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* server: gdb_server: Add colon for target extended-remote
Both GDB commands "target remote" and "target extended-remote" require
to have ":" right before port number.
e.g.
(gdb) target extended-remote :3333
Add ":" to the warning message so that users can copy & past it.
Change-Id: Id6d8ec1e4dfd3c12cb7f3b314064f2c35fa7ab55
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6237
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* jimtcl: restrict memory leak workaround on Linux only
The workaround for jimtcl 0.80 in commit 36ae487ed0 ("jimtcl:
add temporary workaround for memory leak in jimtcl 0.80") issues a
compile time error on macOS:
../src/helper/command.c:157:22: error: aliases are not
supported on darwin
__attribute__((weak, alias("workaround_createcommand")));
The OS is x86_64-apple-darwin19.6.0 and the compiler used is
x86_64-apple-darwin13.4.0-clang.
Restrict the workaround on Linux host only. The fix for 'expr'
syntax change is already merged and the workaround will be dropped
soon.
Change-Id: I925109a9c57c05f8c95b70bc7d6604eb1172cd79
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adam Jeliński <ajelinski@users.sourceforge.net>
Fixes: 36ae487ed0 ("jimtcl: add temporary workaround for memory leak in jimtcl 0.80")
Fixes: https://sourceforge.net/p/openocd/tickets/304/
Reviewed-on: http://openocd.zylin.com/6241
Tested-by: jenkins
* target/armv7m: fix static analyzer warning
Despite of assert(is_packed) clang static analyser complains on use
of the uninitialized offset variable.
Cross compiling with latest x86_64-w64-mingw32-gcc hits warnings
src/target/armv7m.c: In function ‘armv7m_read_core_reg’:
src/target/armv7m.c:337:54: error: ‘reg32_id’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
It happens because mingw32 defines assert() without the attribute
"noreturn", whatever NDEBUG is defined or not.
Replace assert(is_packed) by if (is_packed) conditional and call
assert(false) in the else branch.
Change-Id: Id3c7dcccb65106e28be200b9a4d2b642f4d31019
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
* cmsis_dap: fix build on macOS
Compile fails with error:
src/jtag/drivers/cmsis_dap.c:683:28: error: format specifies type
'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
" received 0x%" PRIx8, CMD_DAP_TFER, resp[0]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
Fix the format specifier.
Change-Id: I0a5a1a35452d634019989d14d849501fb8a7e93a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6255
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* cortex_m: do not perform soft_reset_halt on targets without VECTRESET
Change-Id: Ib3df457e0afe4e342c82ad1af25e03aad6979d87
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6209
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* cortex_m: fix VECTRESET detection for ARMv6-M cores
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/arm_dpm: rename 'wp_pc' as 'wp_addr'
The field 'wp_pc' was originally introduced in commit 55eeea7fce
("ARMv7a/Cortex-A8: report watchpoint trigger insn") in end 2009
to contain the address of the instruction which triggered a
watchpoint. Later on with commit 651b861d5d ("target/aarch64:
Add watchpoint support") it has been reused in to hold directly
the memory address that triggered a watchpoint.
Rename 'wp_pc' as 'wp_addr' and change its doxygen description.
While there, fix the format string to print the field.
Change-Id: I2e5ced1497e4a6fb6b38f91e881807512e8d8c47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6204
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
* target/aarch64: fix watchpoint management
The early documentation for armv8a report the debug register WFAR
as containing the address of the instruction that triggered the
watchpoint. More recent documentation report the register EDWAR as
containing the data memory address that triggered the watchpoint.
The name of macros CPUV8_DBG_WFAR0 and CPUV8_DBG_WFAR1 is not
correct as they point to the debug register EDWAR, so reading such
register returns directly the data memory address that triggered
the watchpoint. The code incorrectly passes this address value to
the function armv8_dpm_report_wfar(); this function is supposed to
adjust the PC value, decrementing it to remove the effects of the
CPU pipeline. This pipeline offset, that has no meaning on the
value in EDWAR, caused commit 651b861d5d ("target/aarch64: Add
watchpoint support") to add back the offset while comparing the
address with the watchpoint enabled.
The upper 32 bits of EDWAR are not valid in aarch32 mode and have
to be ignored.
Rename CPUV8_DBG_WFAR0/1 as CPUV8_DBG_EDWAR0/1.
Remove the function armv8_dpm_report_wfar().
Remove the offset while searching the matching watchpoint.
Ignore the upper 32 bits of EDWAR in aarch32 mode.
Fix a comment and the LOG text.
Change-Id: I7cbdbeb766fa18e31cc72be098ca2bc501877ed1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6205
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
* flash/stm32l4x: add missing break statement
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
* github/action: create a permanent 'latest' release
this commit extends the existing snapshot action to create a release named
'latest' with the built binaries for windows.
this 'latest' release will be updated after every push to github.
Change-Id: I75a64c598169241743add3ac9aa7a0337fbab7f2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6127
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* tcl/rp2040: remove empty line at end of file
Change-Id: I212a96b77282b151a8ecbd46a6436e2bbbda4161
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6221
Tested-by: jenkins
* tcl: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
* flash: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
* jtag: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I101c76a638805d77c1ff356cf0f027552389e5d3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6216
Tested-by: jenkins
* target: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
* openocd: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
* Document the buspirate interface driver.
Change-Id: Iaff13fc5187041a840f4f00eb6b4ee52880cf47e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Warn on undefined preprocessor symbols
Preprocessor directives like "#if SYMBOL" silently replace undefined or
misspelt symbols with 0, which makes configuration bugs hard to spot.
Compiler flag "-Wundef" prevents such errors.
Change-Id: I91b7ba2db02ef0c3c452d334601c53aebda4660e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6238
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Remove compatibility macros m4_ifblank and m4_ifnblank
They are at least since Autoconf 2.67 present,
and we are requiring version 2.69.
Change-Id: I41b33d4ebe02198f03cdddcc4a3c1beedd993d78
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure.ac: use a separate folder for Autoconf-generated files
Autoconf generates several files in root folder of the project.
Keep the root folder cleaner by specifying subfolder 'build-aux'.
Align .gitignore accordingly.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: Ied87faba495d9eeb8f98e78c2e2b7e7e596febfb
Reviewed-on: http://openocd.zylin.com/6236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* helper/command: silent debug msg on command register/unregister
Commit e216186fab ("helper/command: register full-name commands
in jim") and commit a7d68878e4 ("helper/command: unregister
commands through their full-name") introduce a LOG_DEBUG() message
each for command registration and unregistration.
The messages above are quite noisy and pollute the log when
debug_level is 3 or higher.
They can be useful to debug the command registration logic, but
for the other debug activities on OpenOCD are just noisy.
Already commit a03ac1ba30 ("helper/command: disable logging of
registered commands [RFC]") was merged to silent the first case
that is now back with additional logs.
Silent both log messages.
Use 'if (false)' to silent them, making easy to re-enable it when
or if someone needs it.
Change-Id: Id8a067e60e822d4ecbddcb036d081298f7e6181f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6220
Tested-by: jenkins
* mem_ap: fix target arch_info type
The target mem_ap appears as an ARM target, thus it allows the
execution of ARM specific commands causing the crash of OpenOCD.
E.g. 'arm mrc ...' can be executed and segfaults.
Replace the incorrect ARM magic number with a dedicated one.
While there, remove the 'struct arm', that is now holding only the
mem_ap's dap, and replace it with a pointer to the dap.
Change-Id: I881332d3fdf8d8f8271b8711607737b052a5699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6213
Tested-by: jenkins
* riscv: drop unused variable
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* riscv: replace macro DIM() with ARRAY_SIZE()
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/zynqmp : Add AXI AP access port
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* drivers/versaloon: use ARRAY_SIZE()
Replace the custom macro dimof() with the OpenOCD macro
ARRAY_SIZE().
Change-Id: I2fe638444f6c16f2a78c1fd558b21550f76282d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6259
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
* openocd: use macro ARRAY_SIZE()
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
* rtos: use ARRAY_SIZE() and simplify rtos_type.create()
Use the existing macro ARRAY_SIZE().
Rewrite the functions rtos_type.create() to simplify the logic.
Change-Id: I8833354767045d1642801d26944c9087a77add00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6261
Tested-by: jenkins
* tcl: remove remaining deprecated commands
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
* help text: remove trailing space
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
* help: fix line size in 'usage' output
The implementation of command 'usage' is broken while checking the
line limit of 76 chars per line (e.g. 'usage load_image') and the
line wrapping is not correct. The same broken code is used for the
first output line of command 'help' too.
When call command_help_show_wrap(), include the command's name in
the string so the whole text would be wrapped.
Change-Id: Idece01ce54994db7e851d8522435ff764b11f3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6223
Tested-by: jenkins
* LICENSES: Add the MIT license
Add the full text of the MIT license to the kernel tree. It was copied
directly from:
https://spdx.org/licenses/MIT.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I94a5dea5ced6421809ea2a3448f8dda19a93f5c9
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6219
Tested-by: jenkins
* stlink: add comment of firmware version for each flag bit
Change-Id: I7f7c7b9c9cfd88125f82662ed864a2c0715140b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6211
Tested-by: jenkins
* stlink: reorder the flag macro by firmware release
The corresponding bit for each macro is changed, but this is not
relevant in the code.
Change-Id: I7039464f5a3d55d008208f44952aadeb815bd5a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6212
Tested-by: jenkins
* tcl/board: Add ST NUCLEO-8S208RB
Change-Id: I384c6ad9b4cbabbc004160677f600d8c4bd3eb71
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6268
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/arm_adi_v5: Fix clear sticky overrun flag during replay of commands
When a WAIT occurs the commands after the WAIT are replayed and the
STICKYORUN is cleared. However if another WAIT occurs during the
command replay, the command itself is resent but the STICKYORUN bit
shall also be cleared. If this is not done, the MEM-AP hangs.
Change-Id: I14e8340cd5d8f58f4de31509da96cfa2ecb630d1
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6278
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: add support for watchpoints
The current implementation of OpenOCD does not support watchpoints for
cortex_a architecture. So, I replaced the add_watchpoint and
remove_watchpoint with the specific implementation for the
cortex a and using the breakpoint implementation and the arm
documentation [1] as reference. In particular, I have made the
following changes:
* added the following functions
- cortex_a_add_watchpoint
This wrapper function check whether there are any watchpoint
available on the target device by calling cortex_a_set_watchpoint.
- cortex_a_set_watchpoint
This function is responsible for settings the watchpoint register
pair. In particular, it sets the WVR and the WCR registers with
the cortex_a_dap command.
- cortex_a_remove_watchpoint
This wrapper function the selected watchpoint on the target device
by calling cortex_a_unset_watchpoint.
- cortex_a_unset_watchpoint
This function sets both the WVR and the WCR registers to zero, thus
unsetting the watchpoint.
[1]
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0464f/BCGDHIEJ.html
Change-Id: I86611dab474cb84836662af572b17636dc68e282
Signed-off-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Reviewed-on: http://openocd.zylin.com/3913
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
* target/cortex_a: fix number of watchpoints
Decrement the available watchpoints only when succeed setting it.
Initialize the available watchpoint with the correct value.
Change-Id: I0f93b347300b8ebedbcd9e718d4ba32b26cf6846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6196
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: add support for watchpoint length of 1, 2 and 4 bytes
Use byte address select for 1 and 2 bytes length.
Use normal mode for 4 bytes length.
Change-Id: I28d182f25145d0635de64d0361d456f1ad96640e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6197
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: fix memory leak on watchpoints
The memory allocated to hold the watchpoints is not freed at
OpenOCD exit.
Free the watchpoint memory at OpenOCD exit.
Change-Id: I518c9ce0dc901cde2913d752e3154734f878b854
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6210
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* helper/jim-nvp: comply with coding style [1/2]
The helper jim-nvp does not comply with OpenOCD coding style due
to typedef of struct and CamelCase symbol names.
While it's trivial fixing the helper and all its current use in
the code, changing these APIs will potentially break a number of
patches pending in gerrit. Gerrit will not trigger any alert, but
the code will generate compile error after the merge.
Add the compile flag "-Wno-error=deprecated-declarations" to keep
as warning (not as error) the use of "deprecated" functions and
types.
Rename all the CamelCase symbols is lowercase and provide struct
prototypes in place of the typedef.
Add a DEPRECATED section to 'jim-nvp.h' where the old CamelCase
symbols and the old typedef are re-declared with compile attribute
'deprecated'.
With this change OpenOCD compiles, but generates warnings.
The remaining changes allover OpenOCD code will be fixed in a
separate patch for easier review.
The patches merged later that still use the old deprecated API
will compile with warnings. This will permit to identify and fix
these cases.
Change-Id: I786385d0f662dbb1be5be313ae42623156d68ce5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6183
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* helper/jim-nvp: comply with coding style [2/2]
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
* server/telnet: fix autocomplete for jimtcl commands
Current autocomplete filters-out some command reported by "info
commands". One of the filter rule concerns the command's private
data.
Every command registered by OpenOCD has its 'struct command' as
private data.
By ignoring commands without private data, we loose several TCL
commands registered by jimtcl, e.g. 'foreach', 'llength'.
By assuming that every command with non-NULL private data has
'struct command' as private data, we risk at best to access
inconsistent data, at worst to trigger a segmentation fault.
Export the already available functions:
- to check if a command has been registered by OpenOCD and
- to get the private data.
While there, rename jimcmd_is_ocd_command() as
jimcmd_is_oocd_command().
Don't filter-out jimtcl commands with no private data.
Check the private data only on OpenOCD commands.
Change-Id: Ib5bf8d2bc5c12440c0cfae438f637c38724a79b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6282
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* helper/list.h: align file to Linux v5.12
Main improvement is in the doxygen comments.
Minimize the delta with kernel file.
Skip the functions hlist_unhashed_lockless() and
__list_del_clearprev() that are relevant only in kernel.
Remove gcc extension "omitted conditional operand".
Change-Id: I2e9ddb54cfe2fa5f7cf18f44726acd144e1f98b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6276
Reviewed-by: <rdiezmail-openocd@yahoo.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* contrib: add an example of using list.h
Change-Id: Ic3d399d7ad2e4d10677cf78d64968040941b74e5
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6280
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* helper/list.h: add mention to the example in contrib
Without such reference, it could be difficult to find the example.
Change-Id: Ia9ffb06bc1a45446c2c7b53197ab3400e1d8a9e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6281
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* tcl/target/stm32f4x: fix hardcoded chip name
Fixes: c945d6e616 ("tcl/target: start using the new TPIU/SWO support")
Change-Id: I4543c9a204f7b4b3b14e6eabc5042653106aff0e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6277
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
* Makefile: add special target .DELETE_ON_ERROR
The special .DELETE_ON_ERROR deletes the target file on recipe error.
Otherwise, an incomplete output file may be considered up to date
the next time around. .DELETE_ON_ERROR provides reasonable
protection at virtually no cost.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: I67dca47ae5ddf3786993c87b9991b3046a85f00b
Reviewed-on: http://openocd.zylin.com/6235
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: Log both incoming and outgoing GDB packets
- Made sure that also outgoing GDB packets are logged,
not only the incoming ones.
- Improved the treatment of non-printable characters
in the packets to make it more robust.
Prior to this change:
- Outgoing packets were not printed unless OpenOCD was
re-compiled with _DEBUG_GDB_IO_.
- Non-prinable characters were only treated in incoming
'X' packets.
After this change:
- Both incoming and outgoing GDB packets are logged
on debug_level >= 3, so that both directions of the
GDB channel are visible.
- Non-printable characters are checked for in every packet
so that hey do not interfere with the terminal.
Change-Id: I0613e57ae5059b3279b0abcb71276cf5719a8699
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/renesas_rz_g2: Introduce tcl config file for RZ/G2 devices
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* drivers/jlink: Remove trailing dots
This makes the messages consistent with most of the rest of
the OpenOCD output.
Change-Id: I915a01187e7fc317e02483ac0bbd39ec077d6321
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: Use 'bool' for 'reset_halt'
Change-Id: I974a6360ea7467067511541ac212f2e9d3de7895
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6262
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cmsis_dap: add support for swo commands
Replaced mixed snake_case_CamelCase with snake_case.
Define variables at first-use location.
CMSIS-DAP SWO specification:
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__swo__gr.html
Change-Id: Ieba79b16efd445143f964b614673d041aae74f92
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5820
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Add target_data_bits().
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid non-standard conditionals with omitted operands.
Fixes bug #257.
Change-Id: I05fc6468306d46399e769098e031e7e588798afc
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6271
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/startup.tcl: Do not use 'Yoda conditions'
Change-Id: I5e1bbaf032659dda1b365ef4ec6ea4a635d921ce
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6284
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix build.
Change-Id: I4f2667db91f84f07af354691aac5d4c9e3aea3fa
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Marc Schink <dev@zapb.de>
Co-authored-by: R. Diez <rdiezmail-openocd@yahoo.de>
Co-authored-by: Daniel Anselmi <danselmi@gmx.ch>
Co-authored-by: Evgeniy Didin <didin@synopsys.com>
Co-authored-by: Yasushi SHOJI <yashi@spacecubics.com>
Co-authored-by: Tomas Vanek <vanekt@fbl.cz>
Co-authored-by: Olivier DANET <odanet@caramail.com>
Co-authored-by: Thomas Gleixner <tglx@linutronix.de>
Co-authored-by: micbis <michele.bisogno.ct@renesas.com>
Co-authored-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Co-authored-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Co-authored-by: Jan Matyas <matyas@codasip.com>
Co-authored-by: Adrian Negreanu <adrian.negreanu@nxp.com>
When it doesn't do anything (most of the time) it has negligible
performance impact. With slower remote bitbang, and multiple spike
instances being tested in a single chain, things are sufficiently slow
that if a computer is busy then this is required to pass
riscv-tests/debug.
Change-Id: I8816efedaa0cc3b25734ba8fdc979ee4502284a1
Signed-off-by: Tim Newsome <tim@sifive.com>
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Simplify the code and prevent some field of the instruction from overflowing
Change-Id: I0acade05ad351d0e1918be4b75702b1637aa02c9
Signed-off-by: Xiang W <wxjstz@126.com>
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code not upstreamed.
Change-Id: Ie3e411280f76bc798f1d51c2574cfec148ee0d0d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
With the bitbang performance decrease and talking to slower targets
(daisy chain spike) we more often don't meet the expected keepalive time
for gdb. This addresses the cases I ran into.
Change-Id: Ie69c2c602c3be9c156e508fdfa6d0178f104e1d8
Signed-off-by: Tim Newsome <tim@sifive.com>
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Without it the repeat read test wasn't passing any longer. This is
because 7dd323b26d reduced the remote
bitbang performance. I've notified the mailing list about this.
Change-Id: Ie71592792202423aec89fa889b9e3d2a60a3c25f
Signed-off-by: Tim Newsome <tim@sifive.com>
* configure: do not make Capstone dependency automagic
This adds regular ./configure options to control dependency on the
Capstone disassembly engine. See [0] for the rationale.
[0] https://wiki.gentoo.org/wiki/Project:Quality_Assurance/Automagic_dependencies
Change-Id: I3e16dc5255d650aa1949ccf896b26dc96e522a75
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5985
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure.ac: fix build with libusb0 and without libusb1
Driver 'openjtag' requires both libftdi and libusb1.
The current check is incorrect and the driver is built when
libftdi is present with libusb0 and without libusb1, which causes
the linker to fail resolving the required libusb1 symbols.
Remove the check for libusb0 on driver 'openjtag'.
Create a new adapters group LIBFTDI_USB1_ADAPTERS to hold the
driver 'openjtag'.
Change-Id: I1f5e554b519e51c829d116ede894639cb55a26aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5989
Tested-by: jenkins
* doc: fix over/underfull hboxes in PDF
This adds some cosmetic changes to make the PDF User Manual look
proper.
Building it now requires Texinfo 5.0 which shouldn't be problematic
according to [0]. Commit 79fdeb37f4 is
effectively reverted.
[0] https://repology.org/project/texinfo/versions
Change-Id: I990bc23bdb53d24c302b26d74fd770ea738e4096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5995
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* contrib: rpc_examples: haskell: fix ftbs with current libraries
And get rid of some warnings along the way.
Change-Id: I8fdbe1fa304276be6b0f25249b902b3576aa3793
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5987
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Makefile.am: fix override of target 'check-recursive'
To prevent executing the Jim Tcl tests, the makefile's target
'check-recursive' has been overridden in commit 56d163ce79
("jimtcl: update to 0.77, the current version, enable only
specific modules").
This causes a runtime warning during build:
Makefile:6332: warning: overriding recipe for target 'check-recursive'
Makefile:5098: warning: ignoring old recipe for target 'check-recursive'
Instead of override the makefile's target 'check-recursive',
prevent the recursion by re-assigning as empty the variable
SUBDIRS for this specific target only.
Change-Id: I03d1c467eba42316a59aeed4612d6bdbe6211282
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 56d163ce79 ("jimtcl: update to 0.77, the current version, enable only specific modules")
Reviewed-on: http://openocd.zylin.com/5986
Tested-by: jenkins
* contrib: udev file for Cypress SuperSpeed Explorer kit
lsusb output:
Bus 003 Device 011: ID 04b4:0007 Cypress Semiconductor Corp.
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x0007
bcdDevice 0.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 114
bNumInterfaces 4
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 0
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 1 AT-commands (v.25ter)
iFunction 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x00
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 4
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 5
bInterfaceProtocol 0
iInterface 0
Change-Id: I62f0300199da3551c8774a4a5a4cd106a3ab2904
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3611
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: fix memory leak on multiple '-gdb-port' flag
In the odd case of multiple flags '-gdb-port' during 'target
create' or following 'configure', the new strdup()'ed value will
replace the old one without freeing it.
Free the old value (if it exists) before replacing it.
Change-Id: I1673346613ce7023880046e3a9ba473e75f18b8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6005
Tested-by: jenkins
* udev: fix permission for Ambiq Micro EVK's
Commit 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.") was
initially proposed as http://openocd.zylin.com/3429/ then replaced
by http://openocd.zylin.com/3980/
The initial proposal was for file '99-openocd.rules', in which
MODE="664" was the norm.
After merge of http://openocd.zylin.com/2804/ the new udev rules
in '60-openocd.rules' switched to MODE="660", but the evolution of
the above patch missed this change.
Switch udev rules of Ambiq Micro EVK's to MODE="660" and uniform
them to the rest of the file.
Change-Id: I4b4eea535184ee8569da3264bff4f1fafb5bce4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.")
Reviewed-on: http://openocd.zylin.com/6004
Tested-by: jenkins
* doc/style: fix doxygen error
Doxygen complains about non-closed nested comments:
doc/manual/style.txt:423: warning: Reached end of file
while still inside a (nested) comment. Nesting level 1
(probable line reference: 149)
This is caused by the string '/**' that is interpreted as the
beginning of a comment.
Escape the string to not let doxygen consider it as a comment
While there, replace @code/@endcode with @verbatim/@endverbatim to
properly render the line.
Change-Id: If2a27c4cf659326e317cc4ac8c0b313e97e40432
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5996
Tested-by: jenkins
* flash/nor/max32xxx: fix path of include file
The relative path should have three times '..'.
Issue identified by doxygen:
src/flash/nor/max32xxx.c:85: warning: include file
../../contrib/loaders/flash/max32xxx/max32xxx.inc not
found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Change-Id: Ie7b4948c6770b8acb9eff26e08eea32945ebb219
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5997
Tested-by: jenkins
* Doxyfile.in: fix build out-of-tree
When doxygen is built out-of-tree, it fails to find the generated
file startup_tcl.inc:
src/openocd.c:59: warning: include file startup_tcl.inc
not found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Add '@builddir@/src' to INCLUDE_PATH.
Change-Id: I51f2f6fe7224bba0f8b3db7219f9831de4e67139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5998
Tested-by: jenkins
* doc/manual/primer/jtag.txt: remove duplicated section name
The section name 'primerjtag' is used twice, causing doxygen to
complain:
warning: multiple use of section label 'primerjtag',
(first occurrence: doc/manual/primer/jtag.txt, line 107)
Rename one of them.
Change-Id: Id307915dbc51a7f647fab4fb28ab431e65344d61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5999
Tested-by: jenkins
* Doxyfile.in: exclude libjaylink from doxygen
When build using libjaylink as git submodule, doxygen includes the
libjaylink files and complains for multiple 'mainpage' comment
block, one in OpenOCD and the other in libjaylink:
src/jtag/drivers/libjaylink/libjaylink/core.c:37: warning:
found more than one \mainpage comment block! (first
occurrence: doc/manual/main.txt, line 1), Skipping current
block!
Exclude libjaylink submodule from doxygen.
Change-Id: I5e856817344c9f21f8c26f077a23c00b83cfbcb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6000
Tested-by: jenkins
* openocd: fix incorrect doxygen comments
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
* openocd: fix doxygen parameters of functions
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
* doc/manual/primer/autotools.txt: fix doxygen warning
Commit ab90b87778 ("configure: remove AM_MAINTAINER_MODE,
effectively always enabling all the rules") removes the configure
flag '--enable-maintainer-mode' and its documentation, but have
left a reference to the removed subsection 'primermaintainermode'
and this triggers a warning in doxygen:
doc/manual/primer/autotools.txt:21: warning: unable to
resolve reference to 'primermaintainermode' for \ref
command
Remove the obsoleted paragraph.
Change-Id: I56e69ef033d546d159745bed1b47c6105827e7ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ab90b87778 ("configure: remove AM_MAINTAINER_MODE, effectively always enabling all the rules")
Reviewed-on: http://openocd.zylin.com/6003
Tested-by: jenkins
* flash/stmqspi: fix build error with -Werror=maybe-uninitialized
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/flash/nor/stmqspi.c: In function ‘read_flash_id’:
/src/flash/nor/stmqspi.c:1948:6: error: ‘retval’ may be used uninitialized
Change-Id: Ifd8ae60df847fc61e22ca100c008e3914c9af79b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6012
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: fix build error with -Werror=maybe-uninitialized
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/target/riscv/riscv.c: In function ‘riscv_address_translate’:
/src/target/riscv/riscv.c:1536:13: error: ‘pte’ may be used uninitialized
Change-Id: I51e180b43f9b6996e4e4058db49c179b9f81bcdc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6013
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: [FIX] ARMv8-M does not support VECTRESET
ref: Arm®v8-M Architecture Reference Manual (DDI0553B.m)
D1.2.3: AIRCR, Application Interrupt and Reset Control Register
Bit [0] is RES0
Change-Id: I6ef451b2c114487e2732852a60e86c292ffa6a50
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6014
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* driver/ftdi: skip trst in swd mode
When using the adapter olimex arm-jtag-swd (to convert to SWD a
JTAG-only FTDI adapter), the pin trst on JTAG side is re-used to
control the direction of pin SWDIO on SWD side.
There is a single reset API at adapter driver to assert/deassert
either srst and/or trst. A request to assert/deassert srst can
cause also trst to change value, hanging the SWD communication.
In SWD mode, ignore the value passed to trst.
Change-Id: I5fe1eed851177d405d77ae6079da9642dc1a08f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6006
Tested-by: jenkins
* configure.ac: drop macro 'AC_PROG_CC_C99' from autoconf 2.70
The macro AC_PROG_CC_C99 has been obsoleted by autoconf 2.70 and
triggers a set of warnings from both 'aclocal' and 'autoconf'.
The test of AC_PROG_CC_C99 is now included in AC_PROG_CC.
For autoconf 2.69 and earlier the macro is still required, so
cannot be simply dropped.
Use a conditional test to avoid the warning on autoconf 2.70 but
still use AC_PROG_CC_C99 on older autoconf.
Change-Id: I5e8437f5a826fb63be6d07bcb5bb824f94683020
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6009
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* configure: drop macro 'AC_HEADER_TIME'
The macro AC_HEADER_TIME has been obsoleted by autoconf 2.70.
Not all systems provide 'sys/time.h', plus some old system didn't
allowed to include both 'time.h' and 'sys/time.h' because 'time.h'
was included by 'sys/time.h' and was not properly protected to
allow multiple inclusion.
The macro AC_HEADER_TIME helps to detect such odd case.
Nowadays all the systems properly protect 'time.h', so its safe to
unconditionally include 'time.h', even if it is also included by
'sys/time.h'.
The case of systems without 'sys/time.h' is already covered by
configure.ac through the directive
AC_CHECK_HEADERS([sys/time.h])
Remove the obsoleted autoconf macro and simplify the code by
including 'time.h' unconditionally and check HAVE_SYS_TIME_H to
include 'sys/time.h'.
Change-Id: Iddb3f3f1d90c22668b97f8e756e1b4f733367a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6010
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* README.macOS: explain how to install suitable Texinfo
Change-Id: Ic5906111f412eebd906a9be3fd0e133484def3eb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6026
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* jlink: fix device discovery when network is off
If user specifies a serial number for the jlink device, openocd
extends the search to network jlink devices too, without checking
if the host has a valid and functional network connection. If the
network is not functional, libjaylink returns error. This error
invalidates the discovery on USB, even if it was successful.
Factor-out parts of the jlink_init into separate jlink_open_device
function, use that function to firstly discover and match USB
devices and, if matching device was not found on the USB bus and
serial number was specified, repeat discovery and matching via TCP.
Fixes: https://sourceforge.net/p/openocd/tickets/294/
Change-Id: Iea0de1640d4e5b21ecc7e9c1dd6d36f214d647c2
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: http://openocd.zylin.com/6025
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* README: add missing items for 0.11
JTAG adapters
Cadence DPI, Cypress Kitpro, FTDI FT232R, Linux GPIOD, Mellanox rshim,
Nuvoton Nu-Link, Nu-Link2, NXP IMX GPIO, Remote Bitbang, TI XDS110,
Xilinx XVC/PCIe
Debug targets
AArch64, Cortex-M (ARMv8-M), ARCv2, MIPS64, RISC-V, ST-STM8
Flash Drivers
ATmega128RFA1, Atmel SAM, eSi-RISC, EZR32HG, MAX32, MXC, nRF52, PSoC6,
Renesas RPC HF and SH QSPI, SiFive Freedom E, ST BlueNRG,
STM32 QUAD/OCTO-SPI for Flash/FRAM/EEPROM, SWM050, TI CC13xx, TI CC26xx,
TI CC32xx, TI MSP432, Winner Micro w600, Xilinx XCF
Change-Id: I341618ac5d7189e4f98268cecd66c99447b72af8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6027
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* The openocd-0.11.0-rc2 release candidate
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* Restore +dev suffix
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* steppenprobe: fix file permission
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.
Strip the execution permission.
Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
* github: fix github wokflow while pushing a tag
this fix permits to add correctly the generated artifact (windows binaries)
into the release section.
Change-Id: Ia982370d3a1e08c623ebcabb5ac97e9fb49d00e0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* doc: Fix type in Hooking up the JTAG Adapter
We are talking about adapter connectivity in this chapter. It should
be "dongles" instead of "cables".
Change-Id: I7bd4307765517375caa2af86dfc929d0ef66c3e6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6040
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
* doc/manual: Fix @subpage handling
The subpage "thelist" used to have a title "Pending and Open Tasks"
but the commit c41db358a0 changed it to "The List". With
@subpage, it now renders:
"The List of The List enumerates opportunities for"
instead of
"The List of Pending and Open Tasks enumerates opportunities for"
This commit fix it to
"The List enumerates opportunities for"
Change-Id: Ifee0dcd9b3c9f7e651a8748a7afda99eedea3c5c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6041
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* doc/manual: Fix function name typo
We have both the singular form, register_command(), and the plural form
register_commands().
Change-Id: I905ea83988b8ac70dd809b02d53b646aa4d66697
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6042
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Co-authored-by: Paul Fertser <fercerpav@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Jiri Kastner <cz172638@gmail.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Co-authored-by: Bohdan Tymkiv <bohdan200@gmail.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Co-authored-by: Yasushi SHOJI <yashi@spacecubics.com>
* Fix in write_memory_bus_v1: Read sbcs properly
Fixed an issue with system bus write: sberrors were not properly
detected because of an incomplete read of "sbcs". The read was initiated
but not completed (value not acquired by a second DMI scan).
Added debug prints in case sberror != 0.
Added few comments to explain the algorithm.
Change-Id: Id5eb07f2f1bf8e9afee2dec04b9ff5c5a57f606b
Signed-off-by: Jan Matyas <matyas@codasip.com>
* Updated per review discussion at #577.
Change-Id: I65c07edcd4e86eaa5327280a81f74db0b9c84f9c
Signed-off-by: Jan Matyas <jmatyas@codasip.com>
* Empty commit to re-trigger Travis build.
Change-Id: I95deeb28584a891203c8904be621e48003f069dc
Co-authored-by: Jan Matyas <jmatyas@codasip.com>
This way people can write TCL scripts that rely on these more abstract
properties instead of having to check for the existence of sbaccess,
which is not part of 0.11. (There is a similar feature but things are
named differently.)
Change-Id: I5c95a29ef43cb40c3a73b904f11fa7ca38d87b21
Signed-off-by: Tim Newsome <tim@sifive.com>
I don't know how this worked before. Possibly caused by overzealous
removal of `-rtos riscv`.
Change-Id: I7259267b861ef45655f469ab39cc463d608fe149
Signed-off-by: Tim Newsome <tim@sifive.com>
* Make a few globals const.
Looking through globals to see what needs to be removed, but const
globals are OK.
Change-Id: I4126a3f629daf91b109a3bd7120e4b4f62a9d8ee
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix comment typo.
Change-Id: I0c20837559411410b6870e0d0e52c0179a3a167e
Signed-off-by: Tim Newsome <tim@sifive.com>
AFAIK there is no hardware that implements this, but it should be a
close-to-done starting point in case it is ever required.
Change-Id: I49e3082e8629b1d70b12e8a847c2848e75b04508
Signed-off-by: Tim Newsome <tim@sifive.com>
* Remove `-rtos riscv`.
`-rtos hwwthread` is target-independent and a cleaner way to achieve the
same thing.
Change-Id: I863a91f9ad66e37dc36f2fbcbffe403b91355556
* Little more cleanup.
Change-Id: I8fda2317368a94760bc734abc7f1de6ee5b82a7c
* Clean up some more.
Change-Id: I64a1e96aa3bd8c0561d4d19930f99e9bc40eab86
* Get rid of riscv_[sg]et_register_on_hart
Change-Id: I5ea9439bad0e74d7ed2099935e7fc7292c4a2b7f
* Remove hartid arg from set_register.
Change-Id: Ib560e3c63ff32191589c74d3ee06b12295107c6f
* Remove more references to hartid.
Change-Id: Ie9d932fb8b671c478271c1084dad43cad3b2bfbc
* Remove some unused code.
Change-Id: I233360c6c420d1fc98b923d067e65a9419d88d7b
Signed-off-by: Tim Newsome <tim@sifive.com>
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/target/riscv/riscv.c: In function ‘riscv_address_translate’:
/src/target/riscv/riscv.c:1536:13: error: ‘pte’ may be used uninitialized
Change-Id: I51e180b43f9b6996e4e4058db49c179b9f81bcdc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6013
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It doesn't have any effect on real hardware, and by caching the value we
pretended it did.
Fixes#564
Change-Id: I9f4e2cc8abddee61435bbd8d992cbff971a0c28d
Signed-off-by: Tim Newsome <tim@sifive.com>
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
The comment should refer to reading rather than writing.
Change-Id: I72937bb48053233ab5e48d343c4bd1e394f77bda
Signed-off-by: Craig Blackmore <craig.blackmore@embecosm.com>
Add `riscv info` command. Final output is "TCL format" and looks like this:
```
hart.xlen 64
hart.trigger_count 4
dm.abits 6
dm.progbufsize 2
dm.sbversion 0
dm.sbasize 0
dm.sbaccess128 0
dm.sbaccess64 0
dm.sbaccess32 0
dm.sbaccess16 0
dm.sbaccess8 0
```
* Add `riscv info` command.
This command displays some basic information that OpenOCD has detected
about the target. The output is displayed in YAML so it can easily be
parsed. Example of current output:
```
Hart:
XLEN: 32
trigger count: 4
Debug Module:
abits: 6
progbufsize: 2
sbversion: 0
sbasize: 0
sbaccess128: 0
sbaccess64: 0
sbaccess32: 0
sbaccess16: 0
sbaccess8: 0
```
Change-Id: If920c083ff6ec9f482c50f913cd8ceaa62461217
Signed-off-by: Tim Newsome <tim@sifive.com>
* Disable workflow inherited from upstream.
Change-Id: Ifc5ed1b4f5ec2278b8bcf3279c9fd462e469fefa
Signed-off-by: Tim Newsome <tim@sifive.com>
* Switch from YAML to TCL "set array" input format.
Change-Id: I3833210e5bf6d7cffc9934c04ec5201ae7732ad8
Signed-off-by: Tim Newsome <tim@sifive.com>
* Remove indent in `riscv info` output.
That was getting a little too cute, and probably more confusing than
helpful.
Change-Id: Ie51416f53ab4b69294962f0565767d370db82867
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix error handling in read_memory_progbuf_one().
Be sure to restore mstatus/s0 even if there is a failure during the
operation.
Fixes#559.
Change-Id: Ib86ca2c7455bad4a668f34703566060a782116db
Signed-off-by: Tim Newsome <tim@sifive.com>
* Style fix suggested in review.
Change-Id: I444112a9dffea483b7d0e5f96ef7bbdaf58d249f
Signed-off-by: Tim Newsome <tim@sifive.com>
This is a fix for an issue reported by Joe Stoy at:
https://sourceforge.net/p/openocd/mailman/message/37128537/
When clearing sbcs.sbbusyerror, preserve other bits in the sbcs
register that are needed for subsequent system bus transactions.
The use of 'void *' makes the pointer arithmetic incompatible with
standard C, even if this is allowed by GCC extensions.
The use of 'void *' can also hide incorrect pointer assignments.
Switch to 'uint8_t *' and add GCC warning flag to track any use of
pointer arithmetic extension.
Change-Id: Ic4d15a232834cd6b374330f70e2473a359b1607f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5937
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This lets a user see exactly what period of time was sampled, without
having to guess how much time the target was ignored in between bursts.
Change-Id: I5c0639528636bf1a88f249be3ba59bec28c001e2
Signed-off-by: Tim Newsome <tim@sifive.com>
* Allow riscv_semihosting without 16 bit access to memory with instrustions
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* rename *_by_any_size to riscv_*_by_any_size
Used histogram diff strategy, which was much better than the default.
Conflicts:
doc/openocd.texi
src/flash/nor/fespi.c
src/jtag/drivers/libjaylink
src/rtos/rtos.c
src/target/riscv/batch.c
src/target/riscv/encoding.h
src/target/riscv/riscv-011.c
src/target/riscv/riscv-013.c
src/target/riscv/riscv.c
src/target/riscv/riscv.h
src/target/target.c
tcl/target/gd32vf103.cfg
Change-Id: I1321f62ba719419e58f93b2195f2540bd62f50d2
The commit b68674a1da ("Upstream tons of RISC-V changes.") was
proposed well before commit 3ac010bb9f ("Fix debug prints when
loading to flash"), but the merge got in different order.
After latest merge, the master branch fails to compile.
Fix the compile error.
Change-Id: Ia3bd21d970d589343a3b9b2d58c89e0c49f30015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5856
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
* Do not throw error if RISC-V tselect unimplemented
A RISC-V hart without Trigger Module may not implement any of the
associated CSRs such as tselect according to the specification.
riscv_enumerate_triggers previously threw an error in this case, but
only on the first invocation due to r->triggers_enumerated being set
regardless of this. Due to the propagation of this error condition to
disable_triggers and riscv_openocd_step, such a hart would remain
halted after the first 'step' (or 'continue') of a debug session.
This problem can be reproduced with the Ibex RISC-V CPU when
the DbgTriggerEn parameter is set to zero.
This commit changes the behavior of riscv_enumerate_triggers to
return ERROR_OK when tselect was not readable. This fixes the
described malfunction.
Change-Id: Ie813cb119b03702fe708801b5f3581f9bf337243
Signed-off-by: Tobias Kaiser <kaiser@tu-berlin.de>
* Add debug message if RISC-V tselect not readable
Change-Id: Ic3ad5bff9de5c50142cad983f351ce0099cec5c8
Signed-off-by: Tobias Kaiser <kaiser@tu-berlin.de>
* RISC-V triggers: continue if tselect is unreadable
In riscv_enumerate_triggers, even if for one hart tselect cannot be
accessed, other harts might provide trigger support. For this reason,
"continue;" is the appropriate action on a read failure of tselect,
which indicates that triggers are not implemented, instead of
"return ERROR_OK;".
Change-Id: Ied56f3e237b76195a15bfde159532eda9d347d21
Signed-off-by: Tobias Kaiser <kaiser@tu-berlin.de>
* Add memory sampling feature.
Currently only gets 10 samples per second, but the overall scaffolding
looks like it works.
Change-Id: I25a2bbcba322f2101c3de598c225f83c902680fa
* Basic memory sample speed-ups.
977 samples/second.
Change-Id: I6ea874f25051aca1cbe3aa2918567a4ee316c4be
* Add base64 dumping of sample buffer.
We can't just dump raw data, because the API we use to get data to the
"user" uses NULL-terminated strings.
Change-Id: I3f33faaa485a74735c13cdaad685e336c1e2095f
* WIP on optimizing PC sampling.
1k samples per second on my laptop, which is roughly double what it was.
Change-Id: I6a77df8aa53118e44928f96d22210df84be45eda
* WIP
Change-Id: I4300692355cb0cf997ec59ab5ca71543b295abb0
* Use small batch to sample memory.
5k samples/second. No error checking.
Change-Id: I8a7f08e49cb153699021e27f8006beb0e6db70ee
* Collect memory samples near continuously.
Rewrite OpenOCD's core loop to get rid of the fixed 100ms delay.
Now collecting 15k samples/second.
Change-Id: Iba5e73e96e8d226a0b5777ecac19453c152dc634
* Fix build.
Change-Id: If2fe7a0c77e0d6545c93fa0d4a013c50a9b9d896
* Fix the mess I left after resolving conflicts.
Change-Id: I96abd47a7834bf8f5e005ba63020f0a0cc429548
* Support 64-bit address in memory sampling.
* Support sampling 64-bit values.
* Better error reporting. WIP on 64-bit support.
* Speed up single 32-bit memory sample.
21k samples/second.
* WIP on review feedback.
Change-Id: I00e453fd685d173b0206d925090beb06c1f057ca
* Make memory sample buffers/config per-target.
Change-Id: I5c2f5997795c7a434e71b36ca4c712623daf993c
* Document, and add bucket clear option.
Change-Id: I922b883adfa787fb4f5a894db872d04fda126cbd
Signed-off-by: Tim Newsome <tim@sifive.com>
* Fix whitespace.
Change-Id: Iabfeb0068d7138d9b252ac127d1b1f949cf19632
Signed-off-by: Tim Newsome <tim@sifive.com>
* Document sample buffer full behavior.
Change-Id: Ib3c30d34b1f9f30cf403afda8fdccb850bc8b4df
Signed-off-by: Tim Newsome <tim@sifive.com>
* Actually clear the sample buffer in dump_sample_buf.
Change-Id: Ifda22643f1e58f69a6382abc90474659d7330ac5
Signed-off-by: Tim Newsome <tim@sifive.com>
* Use compatible string formatting.
Change-Id: Ia5e5333e036c1dbe457bc977fcee41983b9a9b77
Signed-off-by: Tim Newsome <tim@sifive.com>
* riscv: work around buggy hart states during reset in some DMs
As described in the comment this change adds, the GD32VF103 DM reports
that the hart is in more than one state while it is resetting. Because
of this, the current code acknowledges resets before they actually
complete. This sometimes prevents havereset from getting cleared as
intended, leading to a spurious "Hart 0 unexpectedly reset!" message the
next time riscv_is_halted() gets called.
To work around this, check for the absence of the unavailable state
rather than the presence of the running or halted states. This behavior
is also arguably more true to the spec than what exists now: Section 3.2
states that "The system may take an arbitrarily long time to come out of
reset, as reported by allunavail, anyunavail."
Change-Id: I34e90a16233125608bce8e4c2414dbead637600e
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* riscv: support custom reset-assert scripts
The reset-assert event is used, if present, to override the default
reset logic for ARM and MIPS cores. Do the same for RISC-V so that
devices with buggy ndmreset functionality (like GD32VF103) or
nonstandard reset sequences can specify the appropriate logic in Tcl.
Change-Id: I5e12077d67509853edb8ef3ad3f037f293a5fbb6
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* tcl/target: support GD32VF103 RISC-V MCU
The GD32VF103 is a low-cost 32-bit RISC-V microcontroller with
peripherals that are more-or-less compatible with the STM32F103 ARM
microcontroller. It is available on several low-cost dev boards, such as
the Sipeed Longan Nano, which is what I am testing on.
Add initial support for this chip, including a workaround for a buggy
ndmreset line (i.e. one that doesn't actually trigger a reset) in its
integrated debug module. Use the existing GD32VF103 flash driver that
was ported from the vendor's code in commit 48e40f3513 ("Add support
for GD32VF103 flash").
Change-Id: Iadac47ceb5437b8e18f3d35901388f10fef9f876
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* tcl/target/gd32vf103: add main flash alias
The GD32VF103 creates an alias to either main flash or the bootloader at
0x0, depending on how it was booted. As such, we want to indicate to
debuggers that the memory at 0x0 is flash and so cannot support software
breakpoints. To do this, add an alias to the main flash in the config.
This isn't strictly accurate in the case where we're running the
bootloader, but it still suits our purpose of fixing breakpoint
behavior.
Change-Id: I9eb8462d354f096eee231c0e5e2bffa538a5903e
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* Improve riscv expose_[csrs|custom] commands
* Add option to specify custom name for registers.
* Allow to call commands multiple times without loss of previous data.
* Make sure the commands can only be used in the config phase (before "init").
* Validity checks and warnings.
* Change commands to be per target.
* Fix memory leaks.
* Also fix unrelated memory leaks to keep valgrind happy.
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* fixes after review
* improve error message
This seems to be completely unused in these two files. It was probably
accidentally copied from riscv-011.c, where it is used.
Change-Id: I3f7ad8b2d26b005d3ea4438e2b3ec46a6c801792
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
These comments appear to have been copied from riscv-011.c, for which
they are accurate. However, it makes no sense to also have them in
riscv.c, because 1) none of the things described are actually in
riscv.c; and 2) riscv-013.c has an entirely different code structure,
meaning everything in the comment is an implementation detail of
riscv-011.c. Remove the copy in riscv.c and just leave the one in
riscv-011.c.
Change-Id: I2873af1522482681325525040b3caad2ddddce9d
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* Allocate RISC-V arch_info during target creation
* Ensured that target->arch_info is allocated as soon as the
target is created. Needed so that per-target config commands
(e.g. "riscv set_mem_access") can be executed also in the
OpenOCD's config phase (before calling "init").
* Added several assert()'s for safety.
Signed-off-by: Jan Matyas <matyas@codasip.com>
* Removed a TODO comment
* Allow to put breakpoints in memories without 16 bit access
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* tmp
* tmp
* tmp
* read/write by any size for breakpoints
* fix style for checkpatch
* Add flexible selection of memory access methods, detection of aampostincrement.
New configuration command introduced: "riscv set_mem_access".
It allows to specify which RISC-V memory access methods (progbuf,
sysbus and/or abstract access) should be tried and in which order
of priority.
Command "riscv set_prefer_sba" is left and works in backward
compatible way, but is marked as deprecated.
First time abstract memory access is executed, it is tried with
set aampostincrement bit. If the abstract command fails or the
address is not incremented correctly, aampostincrement will not
be used for any subsequent accesses.
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
* remove unnecessary variable
* fix doc
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
In target/openrisc/jsp_server.c, an error is logged if the ptr was
already NULL. This cannot happen since the pointer was already
referenced few lines before and openocd would have been already
SIGSEGV in that case, so remove the log.
Change-Id: I290a32e6d4deab167676af4ddc83523c830ae49e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5809
Tested-by: jenkins
* Make checkpatch require Signed-off-by
This will make it easier to send changes contributed here to mainline
OpenOCD.
(Intentionally not including the required line here to make sure I can't
just merge this.)
Change-Id: I089084d38f3e08859d62cf7eface405f37af4799
* Whitespace fix.
This PR isn't building on travis. Maybe because I only changed
.travis.yml. Here's a source change to force a build (hopefully).
Change-Id: I8a828fe1d56a1960bc4bfb91d3d2f3a0790ad571
* Can't check for signoff on sources alone.
Change-Id: I741a299b64bf14857a4e1807b254a7d270b2e466
Signed-off-by: Tim Newsome <tim@sifive.com>
* Actual whitespace fixes.
Why didn't this fail to build before?
Change-Id: I339c03c4ef96546dbef5f16e635921a4fdaf9b35
Signed-off-by: Tim Newsome <tim@sifive.com>
A ton of constants got a new prefix, so I made a lot of changes to
match, but no functional changes.
I did define DTM_DMI_MAX_ADDRESS_LENGTH in batch.c. That definition
never should have been in debug_defines.h, which I missed during code
review.
Change-Id: If5d86660f84bb0a3f2865fb36ef05d6630486d8b
Accessing registers on targets that implement 0.9 or earlier will no
longer work. If you need that we can talk about making it a config
option.
Change-Id: I953b639cf9a92ee9b0422e035da57c1d07504237
* WIP, apply stash with conflicts.
Change-Id: Ia794bde419aa29161c68898d20e30527e69f5a31
* Fix conflict resolution problems.
Change-Id: I4cedc348cf613f98cc5a36886f37c568ca644238
* Add repeat_read command.
Only implemented for sba v1 right now, and poorly tested at that.
Change-Id: I1d9ff63e1dea14b3f6a9f8ba4dad53668bf8038b
* Hide bogus address in repeat_read
Change-Id: Ib66c1fa60df9c7fc7cc87880b0fddc52825b48aa
* WIP make repeat read work with progbuf.
Change-Id: I555f8b880c8bf0d1ed0f3f90c7987a5b516a7a79
* WIP
Change-Id: Ic567cea68355ae907e94bd25185a2c9be6fd798d
* Fix error handling when increment is non-zero.
Change-Id: I5a2f3f2ee948fd4e12c0443a542e85b7b5c5791a
* Correctly(?) handle failures when increment is 0.
I'm not 100% convinced that this ensures every read value shows up in
the output, but it ought to work.
Change-Id: I1af3e7174cf9d5e6f293456fb5ead629e17faaaa
* Don't crash when asked to read no data.
Change-Id: I4061b5c720a43a4f828384ab9eacc89557adfa05
* Remove unnecessary comment.
Change-Id: I1be3d699b86299339b3a830ca1ef13c9f5b9fe0f
* Document `riscv repeat_read`.
Change-Id: I4a0f071f38784b2de034f8c1b0ce75d6d2d326b2
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_ARGUMENTS -f {} \;
This patch also fixes an incorrect function prototype in zy1000.c.
ZY1000 minidriver implementation overrides the function
arm11_run_instr_data_to_core_noack_inner(), but the prototype is
not the same as in src/target/arm11_dbgtap.c and to avoid compile
error it was changed also the prototype of the called function
arm11_run_instr_data_to_core_noack_inner_default().
Change-Id: I476cda8cdb0e1e280795b3b43ca95c40d09e4a3d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5630
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Technically that might be OK, but in practice it probably indicates
something went wrong somewhere. Before this change OpenOCD would crash
if it happened.
Change-Id: I2500ba67ec282915dcf2b2488f2aac9fbfdb23a3
This logic is a little tortured, but it still passes the semihosting
tests that were the cause for the recent rewrite.
Change-Id: Ic6760bb068621ab2a49feb0cf3998fc6957b5cfc
* Accommodate users setting custom triggers.
RISC-V hardware supports many more triggers than gdb can communicate to
OpenOCD. Accommodate users that set triggers by writing tdata* directly,
by disable/step/reenable when a user has done that.
Note that users must set dmode in tdata1 for this behavior to work
properly. Triggers with dmode=0 are assumed to be set and handled by the
software that is being debugged.
Change-Id: Ib0751689c5553aae3a273395b10f5b98326fa066
* Enumerate triggers when resuming from a trigger
Otherwise when we connect to a target that's already halted due to a
trigger, we won't correctly step past it.
Change-Id: I23b9482fa9597af826770f9cebf247b7ba59f65c
* Also disable/reenable triggers around single step.
Gdb is smart enough to disable/step/resume if it set the triggers, but
if a user set them manually it also needs to happen.
Change-Id: I1251bd47199b6f15f61a93e3a521a53f2b677c5f
* Fix whitespace.
Change-Id: Icc240aecbc7e3e36ce4e4d784f5703304334ca13
The name conflict is picked by compiler and it fails to compile for rv64
Fixes
src/target/riscv/riscv-011.c:1014:44: error: too many arguments provided to function-like macro invocation
static int read_csr(struct target *target, uint64_t *value, uint32_t csr)
^
Signed-off-by: Khem Raj <raj.khem@gmail.com>
* WIP making semihosting work with -rtos hwthread.
Change-Id: Icb46f3eeedc1391e8fdc73c3ad8036f20267eb2e
* More WIP.
Change-Id: I670a6e1ba2a13a6ef2ae303a99559a16fdd1bbfb
* Fix halting due to a trigger.
Change-Id: Ie7caa8dde9518bcd5440e34cf31ed0d30ebf29ad
* Fix multicore semihosting without halt groups.
Change-Id: I53587e5234308ed2cc30a7132c86e4c94eb176c4
* WIP
Change-Id: I40630543b08d8b533726cb3f63aa60a62be8ef40
* Fix single core semihosting.
This was the last bug!
Change-Id: I593abac027fa9707f48b7f58163d7089574a0e28
* Fix whitespace.
Change-Id: I285c152970b87864c63803fae61312e5b79dfe6d
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types OPEN_BRACE -f {} \;
Change-Id: I6d1356ed11e2699525f384efb7556bc2efdc299f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5628
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
This fixes a bug where we read PC and marked it cached without actually
updating the cached value. The DPC value was correctly marked as valid
and updated.
Change-Id: Id6d3e94a96b981688b06f7f4a998019f2c02f6f5
* Cache accesses through riscv_[sg]et_register.
This helps a lot with the address translation code, which checks satp
over and over again. Now satp is only read once per halt. It should also
help in a few other cases (but I don't have a good test setup to really
measure the impact).
Change-Id: I90392cc60d2145a70cf6c003d6a956dc9f3c0cc4
* Fix whitespace.
Change-Id: I05c5342d8a461cd8c618a3f60296925e9e84643f
* Don't read registers that we know don't exist.
Change-Id: Ie5c6226b3d4ecb6cf8f0d8954a52fda88e6e5bdd
BUILD_TARGET64 creates a larger test matrix and mostly gates the
building of the aarch64/armv8 target, make that unconditional, which
would help fixing any issues with 64-bit address types anyway.
Rebased by Antonio Borneo after commit 1fbe8450a9 ("mips: Add
MIPS64 support")
Change-Id: I219f62b744d540d9dde9a42e6b63fd7d91df3dbb
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5240
Tested-by: jenkins
If we return failure, then the caller will think something's wrong. But
it could very well be that the hardware doesn't have SATP, in which case
we should just report that the MMU is disabled.
This fixes a bug where flashing wasn't using the target algorithm
because allocating a work area failed.
Change-Id: I16e8e660036d3f8584c0b17e842c4ec8961a8410
Instead of exiting during examine(), spit out a warning, and don't
expose the vector data registers. We do provide access to the vector
CSRs, because maybe they do work? It's just that we have no idea what
the size of the data registers is.
Change-Id: I6e9ffeb242e2e22fc62cb1b50782c2efb4ace0bd
the same semihosting handlers chain is declared twice:
1. in src/target/armv4_5.c
2. in src/target/riscv/riscv.c
to make it simpler we moved the declaration into
'src/target/semihosting_common.c' under semihosting_common_handlers[].
then we used this into both of armv4_5.c and riscv.c
Change-Id: If813b3fd5eb2476658f1308f741c4e805141f617
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5473
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Writing bits to an uninitialized buffer generated false warnings.
Zero buffers before setting them by buf_set_u32|64()
(do it only if bit-by-bit copy loop is used,
zeroed buffer is not necessary if a fast path write is used)
Change-Id: I2f7f8ddb45b0cbd08d3e249534fc51f4b5cc6694
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5383
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
* WIP
Change-Id: I0264a73b7f7d2ce89cc0b80692dbf81d9cdcc2fd
* Reading v* registers appears to work.
Can't really test it though, because gdb doesn't print them right.
Change-Id: I8d66339371c564a493d32f15c3d114b738a455c5
* Total hack to communicate registers to gdb.
Change-Id: Id06c819675f2a5bcaf751e322d95a7d71c633765
* Implement writing vector registers.
Fixed reading vector registers.
Change-Id: I8f06aa5ee5020b3213a4f68644c205c9d6b9d214
* Show gdb the actual size of the vector registers.
This length may be different per hart.
Change-Id: I92e95383da82ee7a5c995822a53d51b1ea933493
* Remove outdated todo comment.
Change-Id: Ic9158b002858f0d15a6452773b095aa5f4501128
* Removed TODO comment.
Filed #449 to track this.
Change-Id: I5277b19e545df2024f34cda39158ddf7d0d89d47
* Nicely handle some errors reading/writing V regs.
Change-Id: Ia7bb63a5f9433d9f7b46496b2c0994864cfc4a09
* Handle DMI busy in sba write.
If we encounter DMI busy on the NOP after a read, we'll never get the
value out because DMI busy is sticky. The read must be retried, but we
don't know whether it was ever issued. Since the read has side effects
(incrementing of the address) this retry must be handled at a higher
layer. So now dmi_op_timeout can be told to retry or not, and if retry
is disabled it'll return an error when busy.
Also actually properly do the retry in dmi_op_timeout(). Previously the
code would not reissue the command and end up returning a garbage value.
Change-Id: I3b52ebd51ebbbedd6e425676ac861b57fbe711b1
* Fix whitespace.
Change-Id: Icb76d964e681b22346368d224d1930c9342343f3
* Handle a few more DMI busy cases.
Change-Id: I8503a44e4bf935c0ebfff0d598fe4c322fda702a
* Explain when to use dmi_op_timeout(retry).
Change-Id: I1a5c6d76ac41a84472a8f79faecb2f48105191ff
* dmi_reset does not affect the current transaction.
That means the retry scheme we had been using works fine. This does
contain some minor tweaks, and now we pass my tests which hammer the DMI
busy case harder.
Change-Id: I13eee384dbba82bc5a5b1d387c75c547afe557b5
* Remove unnecessary changes to make the PR readable
Change-Id: I87079876e6965563cf590e3936b3595aeab8715d
* Move idle to end of line...
... because we go through run-test/idle after the scan.
Change-Id: I21a8cff22471f0b895d8cd8d25373dced9bf1ca9
* Remove unused code.
Change-Id: I07a7cdd2d64ca40a4fe181111a34cf55ff1928d1
The original OpenOCD code issued FENCE & FENCE.i twice for the current
hart (which is harmless, but takes time).
Avoiding this extra FENCE is a slight performance improvement. Per my rough
measurements, this improves performance of certain debugger actions
(single-stepping) by approx. 20% in single-hart systems.
* riscv: Fix bugs. Do not touch SATP if there is no MMU.
In some platform, there is no SATP register at all.
OpenOCD will report unexpected errors if SATP is unreadable.
So, use 'riscv_enable_virtual' to guard SATP access.
* riscv: fix format typo.
Abstract write size (aarsize) to shall always match the real
size of the register. This is because abstract write of smaller size
than the register need not be supported per spec (pg. 13 of RISC-V
External Debug Support ver. 0.13.2).
Fix memory access on 64-bit targets with no progbuf and sba that
supports 32-bit accesses but not 64-bit accesses. Bug was introduced in #419.
This fixes https://github.com/riscv/riscv-tests/issues/217.
Change-Id: Ib5ddf9886b77e3d58fe1d891b560ad03d5a46da1
When allocating scratch memory within RISC-V target
(scratch_reserve()), take into account whether progbuf
is writable or not, as determined by examine_progbuf().
* fix for batch scans not honoring presence of BSCAN tunnel
* fix formatting to placate checkpatch
* replace DIM with ARRAY_SIZE
* Refactor code that adds a bscan tunneled scan.
* Move bscan tunnel context to the batch structure, and in array
form, one per scan
* adjust code that was inconsistent with project code formatting standards
* 64-bit progbuf memory reads work.
Change-Id: Ia3dbc0ee39a31ed0e5c38bbb3d9e089b2533f399
* 64-bit writes work.
Change-Id: Iae78711d715b6682817bb7cce366b0094bda8b23
* Let targets indicate number of supported data bits.
This is used by the default memory read/write functions when creating an
aligned block.
I'm adding this mainly to ensure I get coverage of the 64-bit progbuf
memory read/write code.
Change-Id: Ie5909fe537c9ec3360a8d2837f84be00a63de77b
* Make mingw32 happy.
Change-Id: Iade8c1fdfc72ccafc82f2f34923577032b668916
* Add riscv_batch_available_scans().
This function will query the number of available scans in a batch.
* Perform SBA writes with batch transactions for improved performance.
Using batch transactions avoids an unnecessary dmi read after every
dmi write, resulting in a significant performance improvement.
* Align algorithm stack to XLEN.
This fixes algorithm timeout on RV64 targets.
Also improve debug information in various places.
Change-Id: Id3121f9c6e753c6a7e14da511e4de0587a6f7b4d
* Compile 32-bit RISC-V algorithms for RV32E.
Change-Id: I33a698c0c6ba540de29fa0459242c72a67b0cbaa
* Remove debug code.
Change-Id: I37c966ce0f2d1fe68cd6ae0724d19ae95ebaf51b
* Dump start of gdb packets escaping non-printable.
Change-Id: Ie5f36b5c9041bfc0e5aa9543f0afe2c4810c2915
* Propagate flash programming errors.
Change-Id: I0c938ce7a1062bcc93426538cbc82424000f37b7
* Improve debug messaging.
Change-Id: I47ac3518f3b241986c677824864102936100adf6
* Add debug output to flash image.
This is helpful when you're debugging the flash algorithm itself, and a
nop when running it through OpenOCD.
Change-Id: Id44c6498c288872cc2cec79044116ac38198c572
* Make timeout depend on how much data is written.
Change-Id: I819efa04cd6f6bd6664afd5c53cc7a8a5c84f54e
* Fix issi erase commands.
This is required to flash HiFive Unleashed.
Change-Id: I33e4869d1d05ca8a1df6136bccf11afda61bfe10
* Fix running algorithm on multicore `-rtos riscv`.
The bug was that poll() might change the currently selected hart, and in
that case we'd access registers on that other hart after the algorithm
is finished.
Change-Id: I140431898285cf471b372139cef2378ab4879377
* Make fespi flash algorithm debugging optional.
Also add a scheme that allows you to see the stack trace of where a
failure occurred if debugging is enabled.
Change-Id: Ia9a3a9a941ceba0f8ff6b47da5a8643e5f84b252
* Clear cmderr by writing all ones.
This should have been part of #389.
Change-Id: Ie40e95fdd904af65c53d1f5de7c8464b27038ec0
* Don't update reg cache in register_write_direct().
This function explicitly bypasses any caches.
Change-Id: Ie3c9a1163e870f80c0ed75b74495079c527663e9
* Use only one hart to run algorithm.
Fixes a bug with `-rtos hwthread` where all harts would run when running
a flash/CRC algorithm, which would probably ruin flashing, and was
unexpectedly changing registers on other harts for the CRC algorithm.
Change-Id: Ia2f600624f4c8d4cab319861fef2c14722f08b53
* Adds support for RISCV Access Memory Abstract Commands
The Access Memory Abstract Command is one of the three optional
methods for reading and writing memory on a complient RISCV
debug module. The previous two options were already implemented
in OpenOCD.
Implementation Notes:
- aamvirtual is hard-coded to false until the design for accessing
virtual addresses is finalized.
- aamsizes corresponding to 8b, 16b, 32b, and 64b are supported.
128b support is postponed until it is required, as it will mean
changes to the read/write_abstract_arg() interface to pass 128b
values.
- aampostincrement is not used and hard-coded to false.
* Changes from review.
* Additional lint fixes and a typo from last commit.
* Fixing a clang error.
* Fixes a last-minute change that broke writes with width > 8b.
* Removing memcpy after adding read_from_buf().
* add opcode for csrrsi and csrrci
* enable MMU while reading/writing memory using progbuf
* fix style issues
* keep old behavior for progbufsize<4, perform r/w/csr only when necessary
* do not pass progbufsize, only write mstatus if changed
* add config option to enable virtualization feature
* throw error if virt enabled but unavaliable, outsource modify_privilege
* support virtualization for read_memory_progbuf_one
gdb has developed a nasty habit of very often reading 30-some
half-words. This change speeds that up significantly.
Change-Id: Iab1b7575bec5c57051c6e630ae292dddf8fe6350
* Make resume order configurable.
This is a customer requirement. Using this option is discouraged.
Change-Id: I520ec19cc23d7837cb8576f69dadf2b922fa2628
* Fix style.
Change-Id: If8e515984c92ce8df52aa69e87abde023897409f
* Make mingw32-gcc happy.
Change-Id: I39852aedec293294b2b2638ab2cc45494fe77beb
* WIP, rewrite of flash algorithm.
Just put all the flashing logic into the algorithm, instead of using an
intermediate format. This should reduce total data written while
flashing by about 9%, and also makes the code much simpler.
Change-Id: I807e60c8ab4f9f376cceaecdbbd10a2326be1c79
* New algorithm works.
Speeds up Arty flashing another 9%.
wrote 2228224 bytes from file /media/sf_tnewsome/SiFive/arty_images/arty.E21TraceFPGAEvaluationConfig.mcs in 86.784538s (25.074 KiB/s)
verified 2192012 bytes in 6.693336s (319.816 KiB/s)
8.66user 13.03system 1:33.91elapsed 23%CPU (0avgtext+0avgdata 12272maxresident)k
Change-Id: Ie55c5250d667251be141cb32b144bbcf3713fce4
* Fix whitespace.
Change-Id: I338d518fa11a108efb530ffe75a2030619457a0b
* Don't reserve so much stack space.
Also properly check XLEN in riscv_wrapper.S.
Change-Id: Ifa0301f3ea80f648fb8a6d6b6c8bf39f386fe4a6
* In theory support RV32E.
Change-Id: Icfe2a40976ae3161f2324e5bb586915aa4c4c7ee
* In theory support RV32E.
At least very basic tests pass.
Change-Id: Ia42e28a3fa020b3e52c92109392c46d009330355
* Fix cut and paste bug.
Change-Id: Ibfea68b39d706f59a8c3aa8153bb4db9803958c6
* Add hacks to make RV32E work with gdb.
gdb currently requires all 32 GPRs to be present, even on RV32E targets.
Once gdb is fixed these hacks can be removed.
Change-Id: Idcde648de2ca1a3f5b31315aab35fac86580af2c
* Cache program buffer writes.
Speeds up flash program by 3%, flash verify by 2%.
Change-Id: I19f8f44f560a1111fa8f4e4fc04ce6de3c94999a
* Remove nop from batch reads.
program @ 22.123 KiB/s, verify @ 47.654 KiB/s (up from program @ 20.287
KiB/s, verify @ 23.148 KiB/s originally).
Change-Id: I7ee19d967b1080336b0088d20e1fc30828afd935
* Use "algorithm" to compute CRC on RISC-V targets.
Use the C compiler to generate the algorithm code. It's better at
assembly than I am. We need separate RV32 and RV64 binaries to handle
shift instructions. I used the code from gdb (libiberty really) because
it returns the correct result. I'm not sure if the table is worth it
since we do have to save/download/restore more bytes now.
riscv_run_algorithm() now properly saves and reads back all registers
used for parameters. It also doesn't check final_pc if exit_point is 0.
Using gdb means I don't know the exact address where the code will end.
Small target.[ch] change to be able to run algorithms at 64-bit
addresses.
Flashing an arty board now:
```
wrote 2228224 bytes from file /media/sf_tnewsome/SiFive/arty_images/arty.E21TraceFPGAEvaluationConfig.mcs in 105.589180s (20.608 KiB/s)
verified 2192012 bytes in 7.037476s (304.177 KiB/s)
9.87user 16.16system 1:53.16elapsed 23%CPU (0avgtext+0avgdata 24768maxresident)k
```
Change-Id: I6696bd4cda7c89ac5ccd21b2ff3aa1663d7d7190
* Clean up formatting.
Change-Id: I7f2d792a2b9432a04209272abb00d8136ee01025
* Inverted Frame to Pseudo Tap for Simpler Hardware to Decode
Given the variable supported message length , a prefix decoding approach is significantly simpler for a pseudo tap architecture with a shift reg of len = max len of packet. This prefix coding packet also makes the message len field redundant , as that is implict in ir_len and the ir selected.
* style patch
* non-conflict with original
* style patch
* style patch
* requested changes
* style-patch
Tim Newsome
Evgeniy Naydanov
Xiang W
Dolu1990
Antonio Borneo
Anatoly Parshintsev
Dmitry Ryzhov
Evgeniy Naydanov
Tomas Vanek
Erhan Kurubas
Jan Matyas
wzgpeter
Marc Schink
Erhan Kurubas
Jan Matyas
Zoltán Dudás
Yasushi SHOJI
Jesse Sheridan
Ernie Edgar
Tarek BOCHKATI
Craig Blackmore
Adrian Negreanu
Samuel Obuch
Tobias Kaiser
Tom Hebb
Jiuyang Liu
Samuel Obuch
Khem Raj
Tommy Murphy
Florian Fainelli
Tarek BOCHKATI
Hsiangkai
Hsiangkai
bluew
Greg Savin
darius-bluespec
dave-estes-syzexion
Nils Wistoff
jhjung81
Paul George