when last==first==0 then mass erase is executed, it's faster.
the page marking was wrong in this case.
Change-Id: I5c579d59b5c4778cf057cb5986e086abdd4209b2
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/232
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the flash module clock was set according to a spreadsheet from freescale, now it's set according to the configuration file used by the Freescale Flash Programmer.
both work, but i think it's better to use the one used by a software that's made by Freescale (should be correct...)
Change-Id: I382197a3eb43dd47ff4b9b83d5e05008d5613fc6
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/223
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
the unlocking procedure erases the flash mem (even if it wasn't locked), so it should be marked as erased after unlocking.
Change-Id: I5cc6a1e1d6cf4e1f243de532eff54111ffd66187
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/222
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
if JTAG debug request fails then halting with a reset should be attempted.
the failure was ignored previously.
Change-Id: Ibec08e2e97f962d164a110c21aaa80bfc17b7f1a
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/221
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
i had assumed two possible halt/debug states:
- halted + debug mode
- running + not debug mode
turns out this one also exists
- halted + NOT in debug mode
added code to handle this in an appropiate way.
Change-Id: Ia0ddcd55d1890c90d100a9e6f5e84ed8dda812a3
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/220
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
now the flash algorithm running on the 568013 checks the buffer_empty bit (instead of the command_finished bit) before trying to write a new word to the flash mem.
this should speed up the flashing procedure. since it is open loop, this change may reduce the risk of failure. flashing will fail if JTAG speed is such that the flash module cannot keep up.
also, the USTAT register is only read once, as suggested in the flow chart provided by freescale (per. ref. manual @ 6-11)
the last step of the flow chart, exiting after commands are complete, is not implemented.
the algorithm will stay waiting for more data. it is up to the PC side to *not* send more data.
Change-Id: I47fe4b50de7da85f80868f5986a89a7e2152616c
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/219
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
moved reset_jtag to the top, since it will be needed in future changes.
also send a define to the .h
Change-Id: I53ef9c02ffa70e7d0416364525a6fbfef855e222
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/216
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
added logging of target error codes to enable automatic error handling from tcl.
the plan is to use a computer to execute a series of tcl commands, the changes allow simple parsing of return messages to detect errors.
Change-Id: Ia98d3bd036e1b6065b475ffff6c1d30baeaf7417
Signed-off-by: Rodrigo L. Rosa <rodrigorosa.lg@gmail.com>
Reviewed-on: http://openocd.zylin.com/215
Tested-by: jenkins
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes an issue when init is called before init_targets has been
executed.
Make sure init_targets is called before init.
Change-Id: Icd5bd4c2a8eea2e399d9de4e331a77560e9672ac
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/235
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The configuration script check for libusb-1.0 availability first and only
if not found check for libusb-0. So if both libraries are installed on the
system the build script will use libusb-1.0
It's possible to force compiling with libusb-0 with the --enable-libusb0 switch.
If the driver support only libusb0 the script check anly for it.
Change-Id: I7eb045d4e2bd553abefad53f3f4023ff46b0f5f6
Signed-off-by: Mauro Gamba <maurillo71@gmail.com>
Reviewed-on: http://openocd.zylin.com/33
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This reverts commit 0ef5a90d93c5a026bcf70132e60e957ae339d1e1
Causes older versions of gcc to break - need to look into a better fix.
This passed through the jenkins build as we originally did not build this module - we do now.
Change-Id: Iafeac8442b2249269ff45a52ccd3e2870920f635
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/214
Tested-by: jenkins
fix issue when using tms_sequence short
see Trac #31
Change-Id: I22a9cd2af59eae4d8a276dae60b6a99d05af53bb
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/201
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The calculation for reg_packet_size in gdb_get_registers_packet() could
generate a wrong result in the case of multiple registers whose size is
not a multiple of 8.
The current calculation sums the sizes for all registers then rounds the result
up to the next multiple of 8.
Instead it should round each register size up individually and sum the results for all registers.
Change-Id: Idfb5e5eeee0e69a6889dbe9769c0bf17feacb63b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
gdb_memory_map() correctly calculates the target specific number of flash banks, but then uses the total number (all targets) instead of the target specific number to construct its GDB response, causing a crash.
Change-Id: I3f8639b3e90303a59753ebe140ce4fff96fd5db0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/199
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't call a variable num_pages if it holds the flash size. Also rearrange
flash size to num_pages calculation to avoid divide-by-zero if there will
be a device with < 1024 byte pages someday.
Change-Id: I2febea39694a2f9750de141f52ec88ae1599c086
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/211
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
in_mask and in_idx are just another encoding of the same state information
that is already kept in bitq_in_state.bit_pos so derive them from that
instead of maintaining them separately.
Change-Id: I4ac6bbe923698a8c1090a785b8babcbb90f82931
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/207
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this at least checks the post conditions after convoluted code.
Change-Id: Idfa8cbedce5288d8bae5743687949f141dfb07b2
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/187
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
in_buff is only ever set to field->in_value and that pointer is still
available when the parsing is restarted so it could just as well be used
directly, removing the need for the static variable.
Change-Id: I3dd7a8315ed5c5bdc3bfb74044f89492bca9816c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/206
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
field->in_value is already checked so it must be non-null here, which means
the else clause can never execute so the entire buffer allocation and
handling code is completely dead.
Change-Id: Id465012a7e607349401d554fc7a8e5db7e967998
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/205
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Check whether the destination is in the program flash or NVM regions,
in the former case, use the normal longword mechanism, not the fast NVM
write.
Change-Id: I7366b7c8919928ee690252df83b99701776aee82
Signed-off-by: Tomas Frydrych <tomas@sleepfive.com>
Reviewed-on: http://openocd.zylin.com/194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a successor to the Flyswatter cable and is very close to the original.
The new revision is based on FT2232H.
Change-Id: Icc6efcf0e4f9d8a10b65df8679b4973f6b375a9f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: David Anders <danders@tincantools.com>
Reviewed-on: http://openocd.zylin.com/193
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Before this commit, openocd used to segfault when probing flash
of an at91sam7x512 (which contains 2 banks of flash). This was due
to the way it systematically insert a new flash bank without setting
its name.
Then, when get_flash_bank_by_name_noprobe() is called, it is doing
a strcmp() on the non-initialized bank->name.
This commit prevents allocation of second probed bank if it is already
allocated (for example, if it is set in a target config file). If a
new bank really needs to be allocated, it ensures that a default name
is set.
Change-Id: I38d15bef1fda2ec746efad37171975136cf7b371
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/171
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
there are no comments about what the rules w.r.t. null pointers
are and it is inconsistent.
It's simply a bug in the app if we ask about the properties of a null
pointer w.r.t. what kind of target it is. It's equally wrong to say
that it is an arm target as that it isn't an arm target.
Change-Id: I0925a6a5c8b38e594ffa7c3ca4390487b5e9b718
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/168
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The CPLD on the xds100v2 expects to see a rising edge on PWR_RST to
enable the outputs. This patch creates that transition correctly by
fixing the direction register for PWR_RST.
THe CPLD will also loop back the data if the LOOPBACK signal is
asserted. Set this signal to an output and keep it clear.
This was tested with a TI DM3730 Beagleboard xM.
Change-Id: I4ea216bef6ae5c40e935741af5c69dc844d5d494
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-on: http://openocd.zylin.com/189
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add flash waitstate support for Atmel SAM3 chips.
* Set default waitstates to 6, to workaround a silicon bug in the SAM3 family
This code has been tested on SAM3U4, SAM3N4 and SAM3N1
based on Change-Id: I477446f9bfb3e910ea3e2414a6e9a75beb14a214
by Jim Norris <u17263@att.net>
Change-Id: I8d360080f6968979ca5e197ad638282cadd18fb7
Signed-off-by: Attila Kinali <attila@kinali.ch>
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/128
Tested-by: jenkins
add support for checking target against the device CLASS rather
then just the PARTNO.
This change also adds the new LM4F family (Blizzard).
Change-Id: Ia9d1e33f1f1c2817c0039a2232ecf932fae072f9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/161
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
stick to convention of "retval" being used as error value to
be propagated and use "flash_flags" local variable for flash
flags read from how.
Change-Id: I63f1f2248b4f4538d6cd7634ae277f7c0aadc346
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/178
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
verify promise of code that more code can be pasted with an
assert at the end condition of the code passage that builds
string.
Change-Id: I76a4e5f91b9142fff932e1493cb43c29eb6a0f80
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/143
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
variable is subsequently not used
Change-Id: I177d21c6ba9f1f2e3765feffdbf317ea375a8cfe
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/149
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
fixes clang warning. Basically the next address pointer is not
used for anything in the fn, except to be examined in debug.
Change-Id: I253519b8e49e54490bbe7da8ec3d2dd31f49052a
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/155
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
check if no target is selected and return error.
Change-Id: Ie8abb63c708d09572b45e88fc6766af108715077
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/148
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This rename is in preparation for cortex_m4 support.
Change-Id: Ic08c298ec6ed2aabc2c39db67191f68b3a51f550
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/147
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
found by clang, would have done something undefined and mysterious
later on.
Change-Id: If7d7aca8514575d229ed0b17378bf8b1bbf347c4
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/133
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
return error when target can not be found instead of ERROR_OK,
split fn.
Change-Id: Iba5232d3862a490d0995c3bfece23685bd6856e3
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/131
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this was a false positive, silence it.
Change-Id: I432e0c466c94cf8fd6bbf0ea153c8501a8a261eb
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/126
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
"Value stored to 'retval' is never read": Check and propagate error
"Dereference of null pointer": Probably bogus, maybe triggered by the null
check on armv7a, so remove the check since it can't be null anyway.
Change-Id: I3bc44e52af1589ff40e6a42deda0ce7f3a25e397
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/119
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Also fix a spelling error and remove the declaration for a non-existent
function from the header.
Change-Id: I13177e2d81aa167c05c1cc766f06924211e6d735
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/118
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Propagate errors unchanged.
Free allocated working area in the error return path.
Remove duplicated cleanup code by rewriting the logic.
As a side-effect, fixes a scan-build warning.
Change-Id: I80e3c0015be672778f916e998c8c2e4f23d7588c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/117
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes commit Evaluate 'script' in the global scope. It caused
Windows builds behave differently than before because path was evaluated twice
and backslashes from Windows' paths got unescaped and effectively wiped out.
Configs could only be passed with "-f ../dir/config.cfg" or "-f
..\\dir\\config.cfg" instead of usual "-f dir/config.cfg" (or using backslash)
as previously.
Change-Id: I13b4abac6dbe6d770cc11a4e61c9421ef340da83
Author: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/40
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GCC doesn't understand that these are in fact initialized if they are
used.
Change-Id: I01988adb0547f785b48d869ddbe44cc17dca4739
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/116
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The fix is inline with the Linux coding style that forbids
assignment in if condition
Change-Id: I0b9d0b419d9c8b7a8c755e048d5faf72d1658ba2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/87
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The fix is inline with the Linux coding style that forbids
assignment in if condition
Change-Id: I10338a249bcfeff87d8596f7e17f209e26b41678
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/86
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The fix is inline with the Linux coding style that forbids
assignment in if condition
Change-Id: I42a371d6adfdf3b3fb867705211c47d89776ee2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/85
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Total of 5 warnings:
3x "Dead store": removed dead assignment to variable;
1x "Dereference of null pointer": this is not an error, but a
limited visibility of clang, since pointer erase_region_info
is initialized inside cfi_fixup_non_cfi();
1x "Branch condition evaluates to a garbage value":
this is a real coding bug that could issue SIGSEGV, since
"goto cleanup" can be executed before initialization
of "source".
Change-Id: Id3c323c82bb15cbd3bb8fc04b23541f11145f109
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/84
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This should silence a warning.
Change-Id: Id91a9ebacae836083b1db2654a8e7bf24b2300e9
Signed-off-by: Edgar Grimberg <edgar.grimberg@gmail.com>
Reviewed-on: http://openocd.zylin.com/52
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Perhaps we could do one better and propagate the error?
Change-Id: Idc45f516c26f09de4ee01fe05e8d3475f4b80db3
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/43
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
may be used uninitialized in this function [-Werror=uninitialized]
Change-Id: Ida2cf8efe4e7da6fd9f669b806a20894563ac3d4
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/49
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Fix a few errors with set and unused variables detected by GCC 4.7.0
Change-Id: I59b748e18e514ee9f0cde7883b4ed5116198bd4a
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/36
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code in xscale_receive() that tries to skip invalid reads (i.e.
reads that don't have the DBG_SR[0] 'valid' bit set) seems to be
wrong, as it only looks at the first word's valid flag rather than
each word's own valid flag. Am I reading the code correctly? If so,
the attached patch should fix it.
If this looks correct, I'll generate a proper patch and commit message.
Matt
Change-Id: I74ebe2ad7a36d340a9dd3b8487578b6ea7f3cf1e
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/32
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
by immediately polling again when we have received a message from
the target instead of waiting 100ms, we can hope for much better
performance. More than 100x? :-)
Change-Id: Ieaf0c6c8b6e5addc482895670ffbf9a743e07a29
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/27
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Change-Id: I1453f4f3dc0add529da20577e38b8b82d7d00366
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/18
Reviewed-by: Alex Austin <alex.austin@spectrumdsi.com>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Let the target algorithm be running in the background and buffer data
continuously through a FIFO. This reduces or removes the effect of latency
because only a very small number of queue executions needs to be done per
buffer fill. Previously, the many repeated target state changes, register
accesses (really inefficient) and algorithm uploads caused the flash
programming to be latency bound in many cases. Now it should scale better
with increased throughput.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Access the different flash banks' registers using a bank specific register
base and a register specific offset. This is equivalent but feels more
natural.
Some accesses were discovered that maybe should not be hard coded to bank0
registers. Add a note about that.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Split armv7m_run_algorithm into two pieces and use them to reimplement it.
The arch_info parameter is used to keep context between the two calls, so
both calls must refer to the same armv7m_algorithm struct. Ugly but works
for a proof-of-concept.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
On supported targets, this may be used to start a long running algorithm in
the background so the target may be interacted with during execution and
later wait for its completion.
The most obvious use case is a double buffered flash algorithm that can
upload the next block of data while the algorithm is flashing the current.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Target events are added to get better gdb support. The run
algorithm functionality are implemented to support feature
fast flash write functionality. The new r/w buffer api is now
used to support the special memory address handling. The output
of the md command was fixed.
This is a proof of concept to get access to the debug port of a
secured kinetis cpu. On full flash erase the cpu is automatically
secured and the debug port is not accessible.
To get this to work the srst line is needed and the necessary
configuration should be added to the configuration file.
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
added an attempt to use the non-reseting halting sequence. if it fails, then the full sequence will be attempted. this makes things a bit faster most of the time.
changed the location of a function, avoiding a forward def
added an alternative way to enter debug mode, which does not require restarting the chip.
this will not always work, but in general it will (failure 0.3%), and failure is not a dramatic issue, simply have to use the full sequence.
the user can only access "halt", which uses the full sequence, so the user should not have any problems.
restarting the chip requires reconfiguring the flash module. the doc is very poor, so i'd rather have the two methods, and live with the 0.3%.
sometimes the master tap will be enabled, since tap switching is required during halt/lock/unlocking procedures.
now irscan handles this, avoiding unnecessary warnings and preventing errors.
got new info regarding setting the chip to debug mode, and locking/unlocking flash memory.
the newer implementation is a bit slower, but always works.
the previous implementation would randomly (as once every 25k-70k times) get the chip into a state where the freescale tool would be necessary. this is fixed now.
added functions to play around with the jtag state machine. they are not the happiest, but are necessary to be able to execute the halting/locking/unlocking sequences.
Conflicts:
src/target/dsp5680xx.c
the user can execute halt, but no enter_debug_mode. modified the error handling to suite this.
the new implementation of unlocking will use enter_debug_mode, and should not get the same errors as the user would, because not being able to enter debug mode is actually success when checking for locked flash.
crc check was always performed on newly flashed data, now it is optional
flash mem can be locked by writing a specific word to a specific address in flash.
to verify flash, target must be halted, and this will (when the new halt sequence is implemented) require reseting the chip. if the target is reset after writing the lock words, then it will lock, hence the CRC will fail because it is not possible to read stuff from the target.
also added a function that resets the jtag state machine.
this is not used yet, but will be soon.
it is implemented to allow strict control over JTAG state machine, necessary to implement to halt and unlocking sequences.
Posted by telekatz@gmx.de in the bettyhacks forum for openocd
0.4.0 and integrated into 0.5.0 by Gunnar Henne.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Due to build warnings introduced in newer versions of ftd2xx we
use strings to report errors rather than result codes. This also
gives us the same behaviour as libftdi.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Scripts sourced via 'script' should evaluate in the global
scope to make it easy to set and reference global variables.
Signed-off-by: Steve Bennett <steveb@workware.net.au>
i had started my code from dsp5683xx, i renamed a bunch of stuff to names i consider to be better.
i believe no one is using this code, so nobody should be affected. (it's not too late to do this change)
After correcting the reply size counter, it should be safe to rely on it
for the number of bytes expected in the USB read, instead of reading the
endpoint maximum. This doesn't make things go any faster but it's nicer and
removes the local buffer.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add a helper function for running the queue if it would overflow otherwise.
Use it to simplify the queue fill level checks and optimize in a few cases
that would previously run the queue prematurely.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
After the reply_index handling is fixed, there's no need to special case
the out scan.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
dtc_queue.reply_index was wrongly being increased during out scans, causing
the queue to be sent before the out buffer was full. This patch increases
raw upload speed by 50% or so.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Indentation was inconsistent and some lines not indented at all. Quickfix
using Eclipse's auto-indentation.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
Pprogram that loads another program into memory is actually writing the
D- side cache.
The instructions it has loaded can't be executed until they reach the
I-cache.
After the instructions have been written, the loader should arrange to
write back any containing D-cache line and invalidate any locations
already in the I-cache.
For the MIPS Architecture Release2 cores, we can use synci command
that does this job.
For Release1 we must use "cache" instruction.
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
For all architectures we use distinct common magic number,
and this should be a uint32_t type.
Otherwise, comparison with macros will yield compilation
warning.
if tap enable/disable failed then a warning was written to the log, but JIM_OK was returned. if using openocd via a TCP interface to the TCL port, there is no way to catch that the command failed (it didn't enable the tap, so it failed)
now it return an error if it fails.
There are some older atmel nor chips which have negated logic for
TopBottom detection. This patch adds a special handling for the old
chips. This is the same mechanism as implemented in linux kernel.
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
before doing anything with the flash module (FM) the clock divider must be set.
if erase_check was the first thing done with the FM after reset then an error would be generated because the clk divider was not set.
now erase_check sets the clk divider.
reorganized code to get rid of compiler warnings
the warning were related to allignment, i do not get these warning on my build system (i've tried setting the compiler flag but it doesn't work, still working on why) so i cannot detect them (yet.)
This corrects two issues found with openocd.
d7f71e7fe9 removed some code that was
being used.
The above then caused even more code to get removed by commit 1cfb2287a6.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Issue warning when the old cmd is used and redirect to new supported one.
These deprecated cmds will be removed at some point.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Use consistent names for the stm32 family flash drivers, eg.
stm32x -> stm32f1x
stm32f2xxx -> stm32f2x
this makes it easier to add support for newer stm32 families.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
When building official releases from tarball, git commit info is not
available in the building environment. Thus, automake should not try to
append the git commit to the version string.
Signed-off-by: Luca Bruno <lucab@debian.org>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The default is -Werror, so warnings become errors
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
A new variable "nobase_dist_pkglib_DATA" is introduced to install
the OpenULINK firmware image to $PREFIX/lib/openocd/OpenULINK/ulink_firmware.hex
Also, the variable "EXTRA_DIST" is used to include the OpenULINK firmware source
in the OpenOCD source distribution.
So far image_load command tries to load ELF binaries to address
discovered by reading p_paddr member of a Program header of an ELF
segment.
However, ELF specifications says for p_paddr : ...Because System V
ignores physical addressing for application programs, this member has
unspecified contents for executable files and shared objects.
ARM ELF specifiaction goes even further, demanding that this member
be set to zero, using the p_vaddr as a segment load address.
To avoid the cases to wrong addr where p_paddr is zero,
we are now using p_vaddr to as a load destination in case that *all*
p_paddr == 0. Basically, this patch re-implements the approach present in
BDF's elf.c, which is used by GDB also (so that we can be consistent).
cygwin does not define sleep, so use our internal win32 version.
caused by commit 9d4aec6bda
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
there was a check in clearing the status register that
called exit() if the target was running. target_write_memory()
has such a check and will report the error correctly.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
only set jtag global pointer if jtag->init() succeeds. Less code,
more clear what the rules are.
Fix nit that error value from init() was not propagated unmodified.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
- works on Cortex-M3 with ThreadX and FreeRTOS
Compared to original patch a few nits were fixed:
- remove stricmp usage
- unsigned compare fix
- printf formatting fixes
- fixed a bug with overrunning a memory buffer allocated with malloc.
Update devices as per the latest programming manual.
We now use the full DEVID to identify the target. Previously we used
a 8bit id but that has now been changed in the manual.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Freescale iMX53 doesn't seem to like unaligned accesses to his memory
mapped registers.
Anyway this patch makes dump_image/load_image 4X faster for every
access through APB.
Signed-off-by: Luca Ellero <lroluk@gmail.com>
accidentally invoked return jtag_execute_queue() in the
middle of a fn. Hmm.... I would have expected gcc or
at least lint to catch this.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the patchup code would get false positives when checking
whether a dbgbase had to be corrected.
The solution is to have autodetect default, with manual override
in scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Could this cause confusion as data sent to write would be flipped
and then if the caller subsequently used the data, e.g. a
compare mismatch might happen?
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Really a Cortex-A specific option, but there is no
system in place to support target specific options
currently and there has been no need for such a system
until now.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
production processor versions increment, thus the version
bits should be ignored for future proofing. e.g.
Engineering sample version == 0x00, production version 0x01
The patch below fixes step <address> on mips_m4k.
Spencer Oliver <spen@spen-soft.co.uk>:
The current code is used on all other arch's - is
there a underlying issue with those aswell ?
I don't think dsp563xx_once_read_register() would ever
be called with len==0, but it would have been broken in
that case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Problem is, trying to print "Hello, world!\n" just prints endless H's, because r1 is never incremented.
One way to fix it would be to add a "++" after "r1".
Fix a bunch of typos.
Most are in code comments, so nothing should break. UNKOWN_COMMAND and
CMD_UNKOWN are not used elsewhere, so correcting the spelling should
also not break anything.
only flush write queue just before waiting for more data,
rather than when fetching more data from the buffer.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Found by inspection: the correct thing in the context is to use
usleep() rather than jtag_sleep(). Relates to JTAG over TCP/IP
only.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
short sleeps are handled via usleep, longer sleeps we round up
to nearest ms.
There was a bug in jtag_sleep() in that it would round *down*
to nearest ms, thus making all <1ms sleeps 0. Found by inspection
rather than symptom.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
as said in the datasheet Section 3.3.2 Organization of buffers
All buffers are big enough to hold 2 KByte of data.
this will double the speed of download
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
this will allow us to use multiple jlink at the same time as when
the USB-Address is specified the PID change from 0x0101 to
(0x101 + usb_adress)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The default pid of the segger is 0x0101
But when you change the USB Address it will also
pid = ( usb_address > 0x4) ? 0x0101 : (0x101 + usb_address)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
useful for debugging without access to hardware to e.g.
regression test, reproduce memory corruption problems,
etc.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This patch fix a possible read buffer overflow in ft2232_execute_queue.
Also the correct read queue size for libftdi and libftd2xx was added and
and tested.
In function ft2232_write a uninitialized value was initialized because we
don't know if this value was set in the ftdi api call.
it will allow to be at the highest speed of the jlink without touching the
board or cpu config
tested on sam-ice v5 and at91rm9200-ek
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
This patch add rudimentary gdb support. The gdb register list
order is corrected. All registers are now 32bit width. Events are
send to signalize gdb the current target status. Resume and step
function was corrected to consider a modified pc register. Read/write
memory now support L memory type, this means a memory with alternating
y/x memory words. The memspace variable, used by gdb, is now observed
before a default memory access is initiated. Dummy functions for breakpoint
and watchpoint are added.
This patch tries to make some order in "apsel" mess.
"dap apsel" command was quite useless (and broken) by itself.
With this patch we can use it to select between AHB or APB memory access
(previous patch 05ab8bdb81 was somehow broken).
- moves member apsel (in struct adiv5_dap) to ap_current
- adds apsel member
this strange choice is made trying to keep coherence in "dap apsel" command
and to keep compatibility with other code (for example cortex_a8).
Signed-off-by: Luca Ellero <lroluk@gmail.com>
This patch move the dsp563xx_target_create function to the
related code block. Also the target examine function was added
and the register cache is initialized in a separate function. The
missing functionality to invalidate the x memory context on memory
writes was also added.
This patch change the return value on a jtag communication error
to TARGET_UNKNOWN because this function should return the current
target status and not a error code from the underlying api call.
Also the validity of the jtag_status is extended to all static
bits in this value.
Based on the lpc3180 driver, but released as a separate driver for two reasons:
1) I don't have an lpc3180 to test it against, so it might unintentionally break compatibility.
2) It's using a different OOB layout than lpc3180.
Rewritten so that it no longer borrows code from the NXP CDL library. Instead borrowing code from the u-boot port to lpc32xx, written by Kevin Wells.
Tested on lpc3250 (Hitex LPC3250-Stick). OOB layout is compatible with LPCLinux.
I've been working on Rodrigo on adding support to flash
Freescale dsp56800e devices and have been looking at the
dsp563xx code. I think the define for the JTAG CLAMP
instruction in dsp563xx_once.c is incorrect. It should
be 0x05 according the Freescale AN2074 (and is also
0x05 in the dsp568xx according to AN1935). It won't
actually change anything in OpenOCD since this define
is not used anywhere (as far as I can tell).
dap_ap_select was used in the code at various points, but that can lead to
confusion, without any knowledge of what AP is really selected at some
points.
Some bugs derive from this (for example md/mw doesn't work well after
issueing "dap apsel" command).
Moving it to arm_adi_v5.c (using mem_ap_sel* functions instead of mem_ap_*)
make the code more clear and more easier to maintain.
In the future it should be made "static" to avoid its use outside arm_adi_v5
One further benefit is the various goto has been removed as well
Signed-off-by: Luca Ellero <lroluk@gmail.com>
This patch adds read/write capability to memory addresses not
accessible through AHB-AP (for example "boot ROM code").
To select AHB or APB, a "dap apsel" command must be issued:
dap apsel 0 -> following memory accesses are through AHB
dap apsel 1 -> following memory accesses are through APB
NOTE: at the moment APB memory accesses are very slow, compared
to AHB accesses. Work has to be done to get it faster (for
example LDR/STR instead od LDRB/STRB)
Signed-off-by: Luca Ellero <lroluk@gmail.com>
Save, select and restore AP in cortex_a9_step and cortex_a9_init_debug_access.
Fixes a bug where the wrong AP is selected after a reset.
Signed-off-by: Aaron Carroll <aaronc@cse.unsw.edu.au>
Hello,
this patch add commands to access to x,y and p memory. For run time optimization some local jtag
function was changed to static inline.
Regards,
Mathias
Also i have checked the input of this function and in many cases
a simple byte copy is possible.
I have added this check now and is it possible the buffer is
copied byte by byte and not bit by bit.
With byte boundary input the test looks like this:
buf_set_buf 0x02000000 iteration test:
runtime (seconds): old: 6.828559 new: 0.436191 diff: 6.392368
runtime (seconds): old: 6.853636 new: 0.430389 diff: 6.423247
runtime (seconds): old: 6.794985 new: 0.423065 diff: 6.371920
Without:
buf_set_buf 0x02000000 iteration test:
runtime (seconds): old: 6.370869 new: 5.552624 diff: 0.818245
runtime (seconds): old: 6.420730 new: 5.665887 diff: 0.754843
runtime (seconds): old: 6.583306 new: 5.599021 diff: 0.984285
Regards,
Mathias
Hello,
this patch adds the missing cpu registers and the correct read/write register functions and fixed
most of the halt/step/resume issues. The complete missing error propagation was added.
+ fix tab/spaces
Regards,
Mathias
If a handler for the reset-assert event it present, skip the usual reset
handling. This is needed, for example, for board-level resets.
Signed-off-by: Aaron Carroll <aaronc@cse.unsw.edu.au>
ARM11 broke with aa61a3b3d8
as the code only checked for arm 7/9.
CFI probably needs work for non-ARM targets but perhaps
not adding working area memory to e.g. MIPS will give
the default slow CFI support.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
ARM Cortex-A9 multi-core chips expose a single TAP/DAP which connects
to both cores. The '-coreid' option selects which core the target
should connect to.
Note that at present, OpenOCD can connect to either core, but not both
simulatenously, until ADI contexts can be shared.
Signed-off-by: Aaron Carroll <aaronc@cse.unsw.edu.au>
ahbap_debugport_init was queueing reads to a local stack variable but
didn't execute the queue before returning. Since the result of the reads
are not used anyway, it's better to pass NULL as the destination instead of
a dummy variable. I changed this throughout the function, even for the
reads that were actually executed.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Added a Perl script to contrib that uses the header files in StellarisWare complete Firmware Development Package provided by TI/Luminary to generate a new list of device IDs
Used Perl script and revision 6734 of TI/Luminary StellarisWare to update device IDs
Hi,
I took the stm32x NOR flash driver and adapted it for the Ember EM357
chip. This chip is very similar to em351 and stm32w so the driver
should be easily extended to support those as well if anyone can get
their hands on some of those for testing.
changelog:
Added NOR flash driver em357
Best regards,
Erik Botö
Find the flash controller by position since it is before the core,
not after it.
This fixes the problem that str9xpec enable_turbo (or any other
str9xpec command) did not work. (See my post in
http://forum.sparkfun.com/viewtopic.php?f=18&t=25542)
Signed-off-by: Santeri Salko <santeri.salko@gmail.com>
LOG_DEBUG() arguments are only evaluated when DEBUG logging
is enabled, do not use arguments that have side effects
like foo++.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove extra \n from LOG_DEBUG, LOG_INFO, and LOG_WARNING messages
Remove LOG_INFO_N
LOG_INFO_N was only used once and had a \n at the end
Change LOG_USER_N calls that end with \n to LOG_USER
Add a working area that is preserved between calls to
mips_m4k_bulk_write_memory - this gives us a speed increase
of approx 3kb/sec during flash writes to the pic32mx.
This area is released during a resume/reset.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
We only use the struct working_area member 'free' as a
true/false type so might as well use a bool data type.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Do not propagate error number to user. This is for internal
programming purposes only. Error messages to the user is
reported as text via LOG_ERROR().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
min_time was effectively ignored, I needed it to program a Lattice MachXO
which uses a RUNTEST to wait for an erase operation, amongst other things.
With this patch pauses happen and I can program the device with an SVF
generated in LSC ispVM (with "Rev D Standard" checked to suppress
nonstandard LOOP statements)
Every NAND driver keeps private copy of "target"
structure.
Prepare infostructure to move private "target"
copy in common/shared struct nand_device.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Table of NAND devices reports operating voltage.
Replace comma with proper decimal dot.
Øyvind: "." is correct for UK/US, but incorrect for
many other languages. OpenOCD is not localized at this
point, so sticking to "." for US/UK should be OK.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
From struct nand_flash_controller :
- remove unused field register_commands;
- remove field controller_ready, exported but
never referenced.
Remove dead code pointed by controller_ready.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch fixes the issue where the OMAP CPU (and possibly others) was mistaken
for iMX51 and therefore had misadjusted debug base.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
I received a number of "-Wshadow" related warnings (treated as errors) while
trying to build on OS X Leopard. In addition, there were two miscellaneous
other warnings in the flash drivers. Attached are two patches which correct
these issues and the commit messages to accompany them.
My system has the following configuration (taken from uname -a):
Darwin 9.8.0 Darwin Kernel Version 9.8.0: Wed Jul 15 16:55:01 PDT 2009;
root:xnu-1228.15.4~1/RELEASE_I386 i386
=== Werror_patch.txt Commit Message ===
compilation: fixes for -Wshadow warnings on OS X
These changes fix -Wshadow compilation warnings on OS X 10.5.8
Compiled with the following configure command:
../configure --prefix=/usr/local --enable-maintainer-mode --enable-jlink
--enable-ft2232_libftdi
=== flash_patch.txt Commit Message ===
compilation: fixes for flash driver warnings on OS X
These changes fix two compilation warnings on OS X 10.5.8:
../../../../src/flash/nor/at91sam3.c:2767: warning: redundant redeclaration
of 'at91sam3_flash'
../../../../src/flash/nor/at91sam3.c:101: warning: previous declaration of
'at91sam3_flash' was here
and
../../../../src/flash/nor/stmsmi.c:205: warning: format not a string literal
and no format arguments
Compiled with the following configure command:
../configure --prefix=/usr/local --enable-maintainer-mode --enable-jlink
--enable-ft2232_libftdi
===
Andrew
error numbers are only reported at DEBUG log levels and
used internally, they are not part of the user interface.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This piggy backs on JTAG so it's not yet pretty, but that
seems unavoidable so far given today's OpenOCD internals.
SWD init and data transfer are unfinished and untested, but
that should cause no regressions, and will be addressed by
the time drivers start using this infrastructure. Checking
in whould get the code working better sooner, and turn up any
structural/architectural issues while they're easier to fix.
The debug adapter drivers will provide simple SWD driver
structs with methods that kick in as needed (instead of JTAG).
So far just one adapter driver has been updated (not yet
ready to use or circulate).
The biggest issues are probably
- fault handling, where the ARM Debug Interface V5 pipelining
needs work in both JTAG and SWD modes and
- missing rewrite of block I/O code to work on both of our
Cortex-ready transports (Current code is hard-wired to JTAG);
relates also to the pipelining issue.
- omitted support to activate/deactivate SWO/SWV trace (this is
technically trivial, but configuring what to trace is NOT.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
----
doc/openocd.texi | 17 ++
src/jtag/core.c | 3
src/jtag/interface.h | 4
src/jtag/jtag.h | 2
src/jtag/swd.h | 114 +++++++++++++++++++
src/jtag/tcl.c | 2
src/target/adi_v5_swd.c | 281 ++++++++++++++++++++++++++++++++++++++++++++++--
src/target/arm_adi_v5.c | 8 +
src/target/arm_adi_v5.h | 3
9 files changed, 425 insertions(+), 9 deletions(-)
The flash bank name is a required element in adding flash banks,
however other than looking at the config file there is no way of
getting the name used in openocd.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
add supoort for xl family boot bank option.
The option byte handling will be cleaned up in a later patch.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch adds the initial dual flash bank support for devices such
as the stm32xl family.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
this allows configuration scripts to export a init_targets proc
rather than setting up the target directly.
This allows for new conventions in how to set up target vs. board
script and how to transfer default settings between board and
target scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the error values is not part of the interface to the user,
so they should never be printed in LOG_INFO or LOG_USER.
Printing them in LOG_DEBUG() rarely makes much sense but
is OK.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Only Tcl comments are now supported. For classic style
commands comments were supported at the end of the line.
Move in the direction of letting the script language
decide syntax, rather than have special rules for some
commands.
Before this patch goes in, the scripts should be updated
to use ;# instead of # for end of line comments.
> mdw 0 1 2
mdw ['phys'] address [count]
zy1000.cpu mdw address [count]
Command handler execution failed
in procedure 'mdw'
> mdw 0 1 #2
mdw ['phys'] address [count]
zy1000.cpu mdw address [count]
Command handler execution failed
in procedure 'mdw'
> mdw 0 1 ;#2
0x00000000: ffffffff
> mdw 0 1
0x00000000: ffffffff
> mdw 0
0x00000000: ffffffff
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the unprotect fn in stm32 needs to unprotect more sectors
than was requested aligned to some boundary.
Print warning when this happens.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
some chips unprotect more than the range asked for. The
protect fn, must unprotect/protect minimally the range given.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Some flash's do not support buffer writes, so we now check
they are supported before trying to use them.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The existing code used incorrect timeout values for the various cfi
operations. We now calculate the timeouts and convert to
msecs if necessary.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
commit 740b9e25b4 broke the drivers
for ftdi and parport due to retval already being defined.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
If the JTAG speed has not been set, then it has no defined
value, add code to propagate the error.
No change to actual behavior as no new failure paths have
been introduced. This is a no-op patch to make subsequent patches
smaller.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* added support for targeting particular tap
* improved file reading
* improved command line parsing
* added progress meter
* more readable time measurement output
Hi everyone,
Since a call went out for patches... been sitting on this for months. For some
reason, the xscale trace buffer is automatically disabled as soon as a break
occurs and the trace data is collected. This patch was a result of the
frustration of always re-enabling it, or else hitting a breakpoint and checking
the trace data, only to discover that I forgot to re-enable it before resuming.
Don't see why it should work this way. There is no run-time penalty, AFAIK.
Along the way, I also cleaned up a little by removing the ugly practice of
recording wrap mode by setting the fill count variable to "-1", replacing it
with an enum that records the trace mode.
I've been using this for months. Comments, criticisms gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Currently the cmd 'cortex_m3 reset_config' will overide the default
target's 'reset_config'.
Chnage the behaviour to use the target 'reset_config' if configured and
fallback if not.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
it's a lie that is somewhere in the vicinity of the
truth. Certainly 64MHz confuses gprof and produces
zero output and no error messages.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
STMicroelectronics controller SMI is not SPEAr specific.
Rename it and change name to every symbol in the code.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Modified spearsmi driver to include support for STR75x
Added missing initialization in tcl file for STR750
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
If flash chip is not listed in the table, or if no flash is
connected, pointer must be properly initialized.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Rather than having to configure/build jimtcl openocd
will do this as part of its own build.
To use an external jimtcl lib specify disable-internal-jimtcl
to the configure step.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
flash programming via flash write_image or gdb load would
produce a bogus error message that the flash chip was to
small.
The solution is to limit the current flash programming
run to the current chip.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
SMI interface hides the real SPI bus between SPEAr and
external flash.
Added comments to highlight the SPI operation, to help a
future rework in SPI generic and SPEAr specific drivers.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
this never panned out and there are enough mistakes in
the code that probably nobody used this.
Use the tcl server and implement a standalone http
app instead works fine.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add comments to assembly flash loader for STM32. Add tiny improvement in
size of the algorithm (40 vs 48 bytes) and tiny speed improvement (~1.5%,
as time is wasted on waiting for end of operation anyway).
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
gdb connect can fail when the flash has not been probed.
During gdb connect, the flash layout is reported, but this
can not be automatically detected for a target that is
powered up and OpenOCD supports connecting to gdb server
even if the target is powered down.
The solution is to turn of the gdb_memory_map feature.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the CPU crashed at some point, poll will discover this.
Previously the poll fn would clear the error and print a warning,
rather than propagating the error.
The new behavior is to report the error back up, but still
clear the error.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Document "-n" option in manual;
Modify "echo" command definition as COMMAND_HANDLER to
easily add help message
Add help message aligned with manual.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
With the new JIMTCL, "puts" only writes to stdout.
To write on telnet port too, "echo" must be used.
This patch gives to "echo" similar commandline option of "puts".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
add missing error handling.
Output warning when assuming maximum flash size in the
family when failing to read.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Implement autodetection of debug base. Also, implement a function solving
various hardware quirks (like iMX51 ROM Table location bug).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch implements "dap_lookup_cs_component()", which allows to lookup CS
component by it's identification.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch adds function called "dap_detect_debug_base()", which should be
called to get location of the ROM Table. By walking ROM Table, it's possible to
discover the location of DAP.
Sadly, some CPUs misreport this value, therefore I had to introduce an fixup
table, which will be used in case such CPU is detected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
So far most of the people have been using existing ARM966E in the
place of ARM946E, because they have practically the same scan chains.
However, ARM946E has caches, which further complicates JATG handling
via scan-chain. this was preventing single-stepping for ARM946E when
SW breakpoints are used.
This patch thus introduces :
1) Correct cache handling on memory write
2) Possibility to flush whole cache and turn it off during debug, or
just to flush affected lines (faster and better)
3) Correct SW breakpoint handling and correct single-stepping
4) Corrects the bug on CP15 read and write, so CP15 values
are now correctly R/W
help would not show help for commands when the command
interpreter was in the wrong mode, which means that
e.g. "help newtap" didn't work, it wouldn't show the
"jtag newtap" help as it was a configuration command.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Collect variable definitions.
Report syntax error to command dispatcher.
Propagate error when unable to open file.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
When usng gdb pipes we need to keep openocd output at a minimum,
otherwise the gdb stdin will overflow and fail.
Make the calls to gdb_port and log_output synchronous to stop this.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
commit 50d5441e2a caused
native windows build to fail.
Firstly this patch fixes the build issue, but it also disables support
for named pipes under Windows. Windows does not support posix named
pipes.
A cross-platfom access layer will need creating before support can be
enabled again.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
there was special support to support pressing 'x' to quit
openocd. ctrl-c is sufficient. The main server loop is already
complicated enough.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
There is an explicit command "log_output" that can
be used to redirect log output to a file, no need
for a hack in the first place.
Before enabling pipes, use "log_output foo" to redirect
log output to the "foo" files.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
ep93xx and at91rm9200 are conditionally built only on arm and were not
updated to reflect changes in command registration handler.
This patch makes them properly compile again, fixing a build failure
experienced on Debian armel.
Signed-off-by: Luca Bruno <lucab@debian.org>
Signed-off-by: Zachary T Welch <zwelch@codesourcery.com>
short story: if the JTAG clock is too high, then the
behavior will be flaky and kludging the code may
seem to make things beter, but really it's just a red
herring.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
capture of progress output would get polling
results. This will break in the example below
where polling output would override the tcl
return value.
capture {sleep 10000; set abc def}
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by using ctrl-z instead of line end, multi-line tcl scripts
can be handled.
Testing: send ctrl-z a couple of times to make telnet enter the
mode where it sends ctrl-z unencoded.
Programs that talk to the tcl_server can send ctrl-z to
indicate end of tcl-let to be executed without having
to worry about telnet protocols.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
with this buffering disabled fancier logging scripts will
be able to process each line as it is output.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
used /dev/mem and mmem() to memory map JTAG registers
into user space and used new configure options to exclude
eCos specific code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
A while back I sent in a patch that adds support for watchpoint lengths greater
than four on xscale. It's been working well, until the other day, when it
caused an unexpected debug exception. Looking into this I realized there is a
case where it breaks: when the length arg is greater than the base address.
This is a consequence of the way the hardware works. Don't see a work-around,
so I added code to xscale_add_watchpoint() to check for and disallow this
combination.
Some more detail... xscale watchpoint hardware does not support a length
directly. Instead, a mask value can be specified (not to be confused with the
optional mask arg to the wp command, which xscale does not support). Any bits
set in the mask are ignored when the watchpoint hardware compares the access
address to the watchpoint address. So as long as the length is a power of two,
setting the mask to length-1 effectively specifies the length. Or so I thought,
until I realized that if the length exceeds the base address, *all* bits of the
base address are ignored by the comaparator, and the watchpoint range
effectively becomes 0 .. length.
Questions, comments, criticisms gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Hi everyone,
Added more LOG_ERROR messsages to watchpoint and breakpoint code, given that the
infrastructure no longer interprets returned error codes. Also changed
existing LOG_INFO and LOG_WARNING to LOG_ERROR for cases where an error is
returned.
Note that the check of the target state is superflous, since the infrastruture
code currently checks this before calling target code. Is this being
reconsidered as well? Also, should we stop returning anything other than
ERROR_OK and ERROR_FAIL?
Comments gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
do not try to interpret "retval" into a string, just
amend a bit about the context of the already reported
error.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
Version 2 of this patch. Code added to breakpoints.c was removed from previous
patch, and item 3 added, per discussion with Øyvind regarding error reporting.
Item 4 added, which I just noticed.
I tried to use a software breakpoint in thumb code on the xscale for the first
time recently, and was surprised to find that it didn't work. The result was
this patch, which does four things:
1): fix trivial cut-n-paste error that caused thumb breakpoints to not work
2): call xscale_set_breakpoint() from xscale_add_breakpoint()
3): log error on data abort in xscale_write_memory()
4): fixed incorrect error code returned by xscale_set_breakpoint() when no
breakpoint register is available; added comment
Item 2 not only makes the xscale breakpoint code consistent with other targets,
but also alerts the user immediately if an error occurs when writing the
breakpoint instruction to target memory (previously, xscale_set_breakpoint() was
not called until execution resumed). Also, calling xscale_breakpoint_set() as
part of the call chain starting with handle_bp_command() and propagating the
return status back up the chain avoids the situation where OpenOCD "thinks" the
breakpoint is set when in reality an error ocurred.
Item 3 provides a helpful message for a common reason for failure to set sw
breakpoint.
This was thoroughly tested, mindful of the fact that breakpoint management is
somewhat dicey during single-stepping.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
I figured since I was poking around in the breakpoint code on other arches, I'd
add this change to those arches that don't do it already. This patch propagates
the return code of <arch>_set_breakpoint() up the call stack. This ensures that
the higher layer breakpoint infrastructure is aware that an error ocurred, in
which case the breakpoint is not recorded.
Normally I wouldn't touch code that I can't test, but the code is very
uniform across architectures, and the change is rather benign, so I figured
after careful inspection that it is safe. If the maintainers or others think
this is imprudent, the patch can be dropped.
Also changed the error code to something more appropriate in two cases where
hardware resources are unavailable.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
you can now set a variable in a script like set version [version].
Also version takes an optional argument "git" to show git version
of source. If git is not installed during the build, then this
will yield an error that is ignored during the build and "version git"
returns an empty string.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Commands that output progress output and no return value
will have the progress output captured.
Commands that do not output progress output(tcl commands)
will return the tcl return value instead.
The advantage here is that it is no longer necessary to
consider which command one is capturing, it works for
either.
Example #1: capture progress output:
set foo [capture help]
Example #2: capture tcl return value
set foo [capture {set abc def}]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
for non_cfi cfi chips free() was invoked on rodata.
The mystery is why this bug has survived for so long.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
sizeof() is a bit less scary than seing assumption
about size of type, no bug as such.
Use NULL instead of 0 for pointers. More obvious that
it is a pointer from code inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
This simple patch fixes a problem I noticed on the xscale where incorrect values
are sometimes reported by the reg command. The problem can occur when
requesting the value of registers in the xscale-specific register cache. With a
couple of exceptions, none of the registers in the xscale register cache are
automatically retrieved on debug entry. This is probably fine, as they are
unlikely to be needed on a regular basis during a typical debug session, and
they can be retrieved when explicitly requested by name using the reg command.
The problem is that once this is done, the register remains marked as valid for
the remainder of the OpenOCD session, and the reg command will henceforth always
report the same value because it is obtained from the cache and is never again
retrieved from the debug handler on the target.
The fix is to mark all registers in the xscale register cache as invalid on
debug entry (before the two exceptions are retrieved), thus forcing retrieval
(when requested) from the target across resumptions in execution, and avoiding
the reporting of stale values.
Small addition change by Øyvind: change 'i' to unsigned to fix compiler
warning for xscale_debug_entry() fn.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I a mail conversation with Øyvind we stated that speed may not be set at
all on case CLOCK_MODE_KHZ and CLOCK_MODE_RCLK. Also there isn't proper
error propagation adapter_khz_to_speed or jtag_rclk_to_speed.
So jtag_get_speed may need some rewrite for error propagation.
CC: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Do not fail startup if communication with target is
not possible.
OpenOCD supports launching without a target connected
or the target powered down.
The user will typically power up the target and issue
a "reset init" + load his application after OpenOCD
is started then.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
This new cmd adds the ability to choose the Cortex-M3
reset method used.
It defaults to using SRST for reset if available otherwise
it falls back to using NVIC VECTRESET. This is known to work
on all cores.
Move any luminary specific reset handling to the stellaris cfg file.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
bitq.c: In function ‘bitq_scan_field’:
bitq.c:224: error: declaration of ‘pause’ shadows a global declaration
/usr/include/unistd.h:429: error: shadowed declaration is here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
committed so as to ease cooperation and to let it be improved
over time.
So far it supports:
- halt/resume
- registers inspection
- memory inspection/modification
I'm still getting up to speed with OpenOCD internals and AVR32 so code is a little
bit messy and I'd appreciate any feedback.
if a tap could not be _enabled_, the error message was
'failed to disable tap'. Fixed that. Also, display the failing
tap's name.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
The patch improves flash erase for STR9x in case of a full bank erase.
Then the chip erase command is used instead which improves speed significantly.
Also I think it might help if e.g. STR912 enters some state where flash banks are locked, and a chip erase command is the key for unlocking the flash.
ocd_ prefix is used internally in OpenOCD as a kludge more
or less to deal with the two kinds of commands that OpenOCD
has.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
if polling is off, then "reset run + halt" would fail
since halt incorrectly assumed the target was in the
reset state as it is the internal poll implementation
that moves the sw tracking of the target state out
of the reset state.
To reproduce:
> reset run; halt
JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1)
BUG: arm7/9 does not support halt during reset. This is handled in arm7_9_assert_reset()
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
back-off algorithm for polling. Double polling
interval up to 5000ms when it fails.
when polling succeeds, reset backoff.
This avoids flooding logs(as much) when working
with conditions where the target polling will fail.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It is useful to know that the printed errors are *all* the
errors there were.
Added missing error handling(found by inspection).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
it can be useful to throttle performance: test
differences in behavior, test performance effect
of long roundtrips.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This flash driver works on more than just two chips.
(Though it does need work still, e.g. to protect more than 64K.
(On non-'3748-A0 chips where errata allow that.))
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make it scriptable, so code can be conditionalized based on
what transport is in use for the session.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For the above targets the exit_point is
optional when used with run_algorithm, so remove it.
This makes updating the algorithm less error prone.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the mips32 uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the armv7m uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm4_5 codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Update the arm_checksum_memory and arm_blank_check_memory
algorithms to use a breakpoint instruction on v5 arch.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Set up more of the Luminary-specific signals, and stop cloning
a few of the JTAG defaults. More comments too.
Still leaves the "dap info 0" bugs unresolved (presumably coupled
to this particular adapter family) where TPIU, ITM, DWT, and other
debug modules wrongly display as extra NVICs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Evan Hunter
rodrigo_l_rosa
Spencer Oliver
Mauro Gamba
Robert Pasz
Philip Nye
Andreas Fritiofson
Øyvind Harboe
Tomas Frydrych
Marek Vasut
Aurelien Jacobs
Kyle Manna
Attila Kinali
Jonathan Dumaresq
Freddie Chopin
Antonio Borneo
Edgar Grimberg
Marc Willam / Holger Wech
Matt Reimer
Spencer Oliver
Michel Jaouen
Simon Barner
Clément Burin des Roziers
Steve Bennett
Mathias K
Luca Bruno
Richard Uhler
Martin Schmölzer
simonqian.openocd
Heythem Bouhaja
Jie Zhang
Evan
Andreas Bießmann
olivier Schonken
Gunnar Henne
SimonQian
Stefan Mahr
Drasko DRASKOVIC
Jie Zhang
Ronny Strutz
Peter Horn
Tomek CEDRO
Freddie Chopin
Damjan Marion
Alan Bowman
Jonas Hörberg
Alexandre Pereira da Silva
Luca Ellero
Jean-Christophe PLAGNIOL-VILLARD
Ali Lown
Andrew Lyon
John and Tina Peterson
Uwe Hermann
Bjarne Steinsbo
Phil Fong
Aaron Carroll
Michal Demin
Thomas Schmid
Eric Wetzel
Erik Botö
Santeri Salko
Michael Schwingen
Jon Povey
Andrew MacIsaac
David Brownell
John Devereux
Paul Richards
Andrew Leech
Mike Dunn
Rolf Meeser
Piotr Esden-Tempski
ddraskovic
Peter Stuge
Flemming Futtrup
Alexander Stein
Wookey
Oleksandr Tymoshenko
Catalin Patulea
Thomas Koeller
Fredrik Hederstierna
Michal Demin