Convert the sysctrl ap port num as a variable to allow support for the
AM2x family of K3 SoCs.
Change-Id: I1b5b55e48240e6654779dd636fdf07bca055e192
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7941
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Firstly, create the TPIU nrf52.tpiu if using the nrf52 target. This is
standard, using AP 0 and TPIU base address 0xE0040000.
Secondly, add a pre_enable handler for this TPIU which configures the
TRACEMUX field of the TRACECONFIG register. This register is reset
every time the MCU resets, so the pre_enable handler creates a
reset-end handler to ensure the register remains set.
Change-Id: I408b20fc03dc2060c21bad0c21ed713eee55a113
Signed-off-by: Frank Plowman <post@frankplowman.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7901
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
While we can read and write from memory from the view of various
processors, all K3 debug systems have a AXI Access port that allows
us to directly access memory from debug interface. This port is
especially useful in the following scenarios:
1. Debug cache related behavior on processors as this provides a
direct bypass path.
2. Processor has crashed or inaccessible for some reason (low power
state etc.)
3. Scenarios prior to the processor getting active.
4. Debug MMU or address translation issues (example: TI's Region
Address Table {RAT} translation table used to physically map
SoC address space into R5/M4F processor address space)
The AXI-AP port is the same for all processors in TI's K3 family.
To prevent a circular-loop scenario for axi-ap accessing debug memory
with dmem (direct memory access debug), enable this only when dmem is
disabled.
Change-Id: Ie4ca9222f034ffc2fa669fb5124a5f8e37b65e3b
Reported-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7899
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The Texas Instruments' K3 devices are a mix of AMP and SMP systems.
The operating systems used on these processors can vary dramatically
as well. Introduce a RTOS array variable, which is keyed off the cpu
to identify which RTOS is used on that CPU. This can be "auto" or
"hwthread" in case of SMP debug etc.
For example:
AM625 with an general purpose M4F running Zephyr and 4 A53s running SMP
Linux could be invoked by:
openocd -c 'set V8_SMP_DEBUG 1' -c 'set RTOS(am625.cpu.gp_mcu) Zephyr' \
-c "set RTOS(am625.cpu.a53.0) hwthread" -f board/ti_am625evm.cfg
Change-Id: Ib5e59fa2583b3115e5799658afcdd0ee91935e82
Reported-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7898
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Describe the SMP Armv8 cores in SMP configuration with coreid
explicitly called out. This allows for gdb session to call the smp
behavior clearly.
Change-Id: Ie43be22db64737bbb66181f09d3c83567044f3ac
Signed-off-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7897
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When _v8_smp_targets is used with V8_SMP_DEBUG=1, describe the targets
as SMP targets. However, the variable expansion is not in the context of
a proc, and a typo in referring to global $_v8_smp_targets causes this
to fail. Just refer to $_v8_smp_targets directly.
Change-Id: Iffe5fd2703bed6a9c840284285e70b8a8ce84e17
Signed-off-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7896
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on cologne
chip gatemate devices.
Change-Id: Ifa1c4ca6e215d7f49bd21620898991af213812e9
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7838
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on intel devices using
a proxy bitstream.
Change-Id: Ib947b8c0dd61e2c6fa8beeb30074606131b1480f
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7837
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on xilinx devices
using a proxy bitstream.
Change-Id: I68000d71de25118ed8a8603e544cff1dc69bd9ba
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7836
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on efinix trion and
titanium devices using a proxy bitstream.
Change-Id: I4a851fcaafe832c35bd7b825d95a3d08e4d57a7b
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7826
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
certus and certus po devices.
Change-Id: I6a8ec16be78f86073a4ef5302f6241185b08e1c6
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7825
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
ecp5 devices.
Change-Id: I4a4a60f21d7e8685a5b8320b9c6ebdc2693bbd21
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7824
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Jtagspi is using a proxy bitstream to "connect" JTAG to the
SPI pins. This is not possible with all FPGA vendors/families.
In this cases a dedicated procedure is needed to establish such
a connection.
This patch adds a jtagspi-mode for these cases. It also adds the
needed interfaces to jtagspi and the pld-driver so the driver
can select the mode and provide the necessary procedures.
For the cases where a proxy bitstream is needed, the pld driver
will select the mode and provide instruction code needed in this
case.
Change-Id: I9563f26739589157b39a3664a73d91152cd13f77
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7822
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the TI K3 family AM62P SoC. This SoC is built on the
same base of AM62A7, so reuse the configuration with the exception of
the JTAG ID and the actual name used for the R5 core (moved from main
domain to wakeup domain).
For further details, see https://www.ti.com/lit/pdf/spruj83
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3a80be9e71204ed7697e51ac1ad488ef405744ef
Reviewed-on: https://review.openocd.org/c/openocd/+/7892
Reviewed-by: Bryan Brattlof <hello@bryanbrattlof.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Add support for the TI K3 family J784S4/AM69 SoC.
For further details, see http://www.ti.com/lit/zip/spruj52
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3c899aed0cb79ab8bbf8077ca6dfe0636cf72288
Reviewed-on: https://review.openocd.org/c/openocd/+/7890
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
$_soc is set per platform, no point in duplicating _CHIPNAME to
explicitly set the information provided by $_CHIPNAME itself.
So move it out after the check for CHIP_NAME
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I60d30d6a9a2ce352f66c5bc03075e4ba638e3062
Reviewed-on: https://review.openocd.org/c/openocd/+/7889
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32WBA5x have a single bank flash up to 1MB
Change-Id: I3d720e202f0fdd89ecd8aa7224653ca5a7ae187b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7694
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added NPCX flash driver to support the Nuvoton NPCX4/K3 series
microcontrollers. Add config file for these series.
Change-Id: I0b6e128fa51146b561f422e23a98260594b1f138
Signed-off-by: Luca Hung <YCHUNG0@nuvoton.com>
Signed-off-by: Mulin CHao <mlchao@nuvoton.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7794
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There was a typo in the register numbering.
Signed-off-by: Robert Kovacsics <kovirobi@gmail.com>
Change-Id: Ie5d306725962c42f1bce976b80968145e6d0a177
Reviewed-on: https://review.openocd.org/c/openocd/+/7860
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add basic connection details with am625 SK/EVM
For further details, see https://www.ti.com/tool/SK-AM62A-LP
Change-Id: I0b6b4004f3a04be7a90207e44c588a4f68aff47a
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7855
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add support for the TI K3 family AM62A7 SoC.
For further details, see https://www.ti.com/lit/pdf/spruj16a
Change-Id: Ie69bde4895f34b04f9967f63d1ca9c8149c50b8a
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7854
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add links for the SoCs are supported by the conf file for future
reference.
Change-Id: Ic5b7786ef3ac31414fe2ce56c1237a18ce99aaa1
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7853
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Sufficient to probe both cores via multiple APs.
No support listed for jtag in the datasheet or usermanual.
Tested against a BW-16 board:
https://www.amebaiot.com/en/amebad/#partner_bw16
Change-Id: Idf82085e7b7327fdf3d6d668e6fb59eff6e0431b
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7847
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This commit provides startup files for the Synopsys DesignWare ARC
HSDK-4xD board. These have been adapted from the corresponding
snps_hsdk.cfg files, the only functional change being the JTAG IDs for
the new board's CPU cores.
Change-Id: I19a0cd13bc09de90cfe2a7cccf1239e459fd8077
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7829
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Board config file for ESP32-S3, to allow communication with
the builtin USB-JTAG adapter.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1310f5db30f7df38fe9344f7ba2334611b53863e
Reviewed-on: https://review.openocd.org/c/openocd/+/7749
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This config file enables communication over USB-JTAG with
ESP32-C3, ESP32-S3, ESP32-H2 and ESP32-C6 chips
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Iceea26972588d8c4919d1f3248684ece48ca9121
Reviewed-on: https://review.openocd.org/c/openocd/+/7748
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ifb0122f3b98a767f27746409499733b70fb7d0e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I36c86fe4ebc99928ce48a5bff8cb9580a0fa3ac0
Reviewed-on: https://review.openocd.org/c/openocd/+/7746
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit enhances code reusability, simplifies maintenance, and ensures
consistency across all chip configurations by consolidating commonly used
commands and variables into the common config file.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9181737d83eeba4e983b6a455b8a1523f2576dd2
Reviewed-on: https://review.openocd.org/c/openocd/+/7745
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Consolidate commonly used commands and variables from
chip config files into functions in esp_common.cfg.
This includes "jtag newtap," "target create,"and "configure -event."
Enhances code reusability and simplifies maintenance.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9e8bf07a4a15d4544ceb564607dea66837381d70
Reviewed-on: https://review.openocd.org/c/openocd/+/7744
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add more ultrascale devices. Set instruction codes for SSI devices
such that refresh/program read_stat and user registers will work.
Change-Id: Id0a0706f4016eb8a4732725a5b72ae61efd73421
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7716
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Adding a single file for each different ir-length.
Change-Id: Iba3dd55b91c28fdb4d0cafa1ededd939fe61a267
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7715
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use configurable virtex pld driver to add support for more
xilinx fpga families.
Change-Id: Iff10c8c511787734fa289bdba15f03131d51e071
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7352
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The current cJTAG to JTAG switching commands for TI chips are not
particularly reliable, especially on chips with accurate timing.
On a Raspberry Pi the existing sequence has (depending on cabling and
chip) a ~50% chance of working, on a much better-behaved FT2232H
it doesn't manage to enable full JTAG at all.
This change runs a bunch of test-idle cycles before actually attempting
to switch to full JTAG. This makes the switch reliable even at high
clock speeds (>100kHz) and from precise sources like the FT2232H.
Change-Id: I9293e884bf3e9606d529756ae4483b844d3c39db
Reported-by: Phil Wiggum <p1mail2015@mail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/375/
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Reviewed-on: https://review.openocd.org/c/openocd/+/7419
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change adds the extensa sample target and board configurations.
it removes the obsoleted vd_xtensa_jtag.cfg from targets.
Change-Id: I9d4d25abde46c0b15e5211a973012447872cb405
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7723
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Initialize clocks to max speed and setup SDRAM. NAND support is still
incomplete. Originally found at:
elinux.org/index.php?title=Calao_Atmel_AT91_development_board&oldid=73933
Updated the code from 2011 and improved it a bit.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I83474e07c8de8cc3b5d058029551935549693ef9
Reviewed-on: https://review.openocd.org/c/openocd/+/7578
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
this new STM32 series family introduces 2 devices:
STM32C011xx (0x443) and STM32C031xx (0x453)
both devices have 32 Kbytes single flash bank.
Change-Id: I4e890789e44e3b174c0e9c0e1068383ecdbb865f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6874
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added support for TMS570LC43xx series parts. This uses the pre-existing
ti_tms570.cfg parent config. In ti_tms570.cfg, dbgbase was changed.
Note 1: Based on the following TI E2E post, the previous dbgbase was wrong
and the new value isn't due to a difference in parts.
Link: https://e2e.ti.com/support/microcontrollers/arm-based-microcontrollers-group/arm-based-microcontrollers/f/arm-based-microcontrollers-forum/1106954/tms570ls3137-debugging-with-openocd
Note 2: Both the previous dbgbase and the one suggested in the TI E2E post
have the 2 LSB set. In the current version of OpenOCD, this will cause
cortex_a_read_cpu_memory_fast and cortex_a_write_cpu_memory_fast to fail
due to an alignment checks in
mem_ap_<read/write>_buf_noincr()->mem_ap_<read/write>().
In all other uses of dbgbase for arm cortex parts, the 2 LSB are masked
and ignored.
Change-Id: Ic936722e5a4cfc7161b0df1fe3325ee12fd901c6
Signed-off-by: Phil Kirkpatrick <p.kirkpatrick@reflexaerospace.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7682
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
They have an ir length of 22, 24 or 38 bit and different command codes.
Change-Id: I488e8613f1c4d017e1590111f60b2725ec62964b
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7387
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add missing ID codes and ignore the version in the ID.
Change-Id: Idd2d3a5eddb6995f3af1c45afd2adf76ce3442bf
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7386
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The old configuration files did not work because of a missing
'at91sam9260minimal.cfg' file. Also, the config files were placed
wrongly. Update them, put them to the proper location, merge the two
supported boards into one, remove now superfluous include, remove
defunct web page, etc.. Tested with a Calao USB-A9G20 and a hacked
'device_desc' to match. Native support for it will come next.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: Iec578c8777c5a6134e132dbac17c2988c7634742
Reviewed-on: https://review.openocd.org/c/openocd/+/7522
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With the new checkpatch we will not get this type of issues
anymore.
In mean time, let's fix what we have missed during the review
process.
Change-Id: Iecebf9d43f51a29ee09505d360792793afd24b40
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 53556fcded ("tcl/interface: add Ashling Opella-LD FTDI config files")
Reviewed-on: https://review.openocd.org/c/openocd/+/7530
Tested-by: jenkins
Use correct register name after it has beed changed
in commit 11ee500bff ("target/armv7m: Rename xPSR to xpsr")
Change-Id: I3648848f4b47af2d20d60c3e0ecef78f75f6d605
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7473
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
It was fixed by e94180571 ("at91sam9: factorise cpu support") in 2011.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I95ea149b45a9902424bf9068b4a2830c17ddc6be
Reviewed-on: https://review.openocd.org/c/openocd/+/7525
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
in raspberrypi-native.cfg
Fixes: bec6c0eb09 (tcl/interface: universal config for all Raspberry Pi models)
Signed-off-by: Tomas Deingruber <Deingruber.Tomas@gmail.com>
Change-Id: I632c8acd84974937849b5fdf2943239def17bd6d
Reviewed-on: https://review.openocd.org/c/openocd/+/7512
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Integrate a rescue mode inspired by [1].
The current OpenOCD must be restarted before normal work with the RP2040
because the rescue debug port must not be activated (or the target
is reset every 'dap init'). To continue without restarting OpenOCD
we would need to switch off the configured rescue dap.
Change-Id: Ia05b960f06747063550c166e461939d92e232830
Link: [1] https://github.com/raspberrypi/openocd/blob/rp2040/tcl/target/rp2040-rescue.cfg
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7327
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Speed calibration coeffs are computed from cpufreq/scaling_max_freq
and from the device-tree compatibility information.
Raspberry Pi linux offers /dev/gpiomem for non-root access
to the GPIO registers since ~2016.
Do not configure 'bcm2835gpio peripheral_base' as it is necessary
only if /dev/mem is used - it requires running OpenOCD as root
- it's a security risk so it should be avoided.
The configuration of the GPIO connector (40-pin header)
is factored out and ready to use in interface configuration
for other driver (e.g. linux gpiod).
Mark raspberrypi2-native.cfg as deprecated and redirect
it to raspberrypi-native.cfg
Change-Id: Icce856fb660b45374e94174da279feb51f529908
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7264
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Same mechanism as in stm32f1x.cfg reused here.
Change-Id: I81f02feb2b655e8259341b22180f3a8b82e28d05
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7438
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The rtos hwthread has been merged in 2019 with commit 85ba2dc4c6
("rtos/hwthread: add hardware-thread pseudo rtos").
During review in patchset 19 the name of the rtos has been changed
from 'hawt' to 'hwthread'.
Some target config file was already merged ready for hwthread, but
keeping the relevant lines commented and still reporting the old
name.
Enable rtos hwtread to the target that were supposed to use it.
Fix the name of the rtos.
Change-Id: I877862dcdba39f26462bb542bac06d1a5f5f222d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7384
Tested-by: jenkins
This patch is picked from the tcl part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support the communication with Nuvoton's Cortex-M4 chips: M541 &
NUC442/472 series.
This patch has been tested with Nuvoton's NuTiny-SDK-NUC472 development
board [2].
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
[2]: https://www.nuvoton.com/export/resource-files/UM_NuTiny-SDK-
NUC472_EN_Rev1.02.pdf
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I27ac58dd1c98a76e791a4f1117c31060cf5522e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7330
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
rp2040-core0.cfg configuration file was intended for a special adapter
which selects a SWD multidrop target on its own. This means
that rp2040-core0.cfg is totally unusable with a standard SWD
adapter. The file was marked as deprecated in 0.12 release.
The reworked rp2040.cfg can be restricted to use just one core:
openocd ... -c 'set USE_CORE 0' -f target/rp2040.cfg
Remove the obsoleted config.
Change-Id: Id886471622bb4a8cb83f5c4c3660657407aaaf74
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7326
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add the variable selected configuration for SMP debug with rtos hwthread.
Use SMP by default.
Change-Id: I1c37d91688a3ab58d65c15686737892965711adc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7242
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.
To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.
Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
instrument "target/stm32x5x_common.cfg" used by both STM32L5x/U5x
to support HLA adapters like "interface/stlink.cfg" in non-secure mode
if the device switches to secure mode, the debug session will be
stopped immediately (with an explanatory message).
Change-Id: I645fdd55e3448ef82d0ddcc396f42fd7b2f39ac3
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Patrik Bachan <diggit@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/317/
Reviewed-on: https://review.openocd.org/c/openocd/+/6546
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Some config changes required to run ESP32-S3 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I38022bb5ff5830e1cf9d11d6fe795ea99d91e9db
Reviewed-on: https://review.openocd.org/c/openocd/+/7254
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some config changes required to run ESP32-S2 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie0a742442254ec6e95d4e05be40213b079a94dab
Reviewed-on: https://review.openocd.org/c/openocd/+/7253
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some config changes required to run ESP32 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I484324f8497ec7934bb73164c638fc5f6460fcc4
Reviewed-on: https://review.openocd.org/c/openocd/+/7252
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The work area should be backed up.
The flash probe runs an algorithm on the target CPU.
The flash is probed during gdb connect if gdb_memory_map is enabled
(is enabled by default).
Without backup the target memory gets corrupted on gdb connect.
Change-Id: I3344b9dc6cbf904d49f3b05ab104b541d1d63422
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7257
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Since all the device definition when accessing device from jtag is also
valid when accessing from swd, lets make sure the configuration can
handle the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5af071137fd8c3b52cc4ef72401f8eba952f9cad
Reviewed-on: https://review.openocd.org/c/openocd/+/7090
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The STM32L5 and U5 devices have DBGMCU_CR trace related bits changed
wrt other STM32 devices.
Fix the setting in configuration script.
Change-Id: I0bbc48e7b1290b603c6966cf5ddd42df389e6ede
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7117
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
- Config files for DAP/JTAG and DAP/SWD systems
- Xtensa core config definitions for NXP RT685 with Xtensa HiFi DSP
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I9c3280052073d86e09c7553de661eb8662a95c4a
Reviewed-on: https://review.openocd.org/c/openocd/+/7145
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Nishanth Menon
Oliver Graute
Frank Plowman
Dubravko Srsan
Peter Mamonov
Daniel Anselmi
Tarek BOCHKATI
Joshua Nekl
Luca Hung
Robert Kovacsics
Kaelin Laundry
Jason Kacines
Karl Palsson
Artemiy Volkov
gudvinr
Ahmed BOUDJELIDA
Erhan Kurubas
Laurent LEMELE
Lorenz Brun
iosabi
Jacek Wuwer
Wolfram Sang
Dominik Wernberger
Tarek BOCHKATI
Phil Kirkpatrick
Julien Massot
Antonio Borneo
Marc Schink
Tomas Deingruber
Tomas Vanek
Andreas Fritiofson
Zale Yu
Kyle Schwarz
Rocco Marco Guglielmi
George Voicu
Paul Fertser
Steve Marple
Ian Thompson
Toms Stūrmanis