Add gdb-attach event to call the "up" function of m3 and m4 allowing for
more seamless integration with gdb for end users. We still retain _up
functions for non-gdb functionality.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Suggested-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2e51fdbd8756f156551e589c748c3a338afa655c
Reviewed-on: https://review.openocd.org/c/openocd/+/6615
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
both stm32l5x and stm32u5x configs are almost identical except
clock config.
while at there rename target procs to avoid issues with JTAG daisy
chaining.
Change-Id: Ibbb1dfeb91a7f8d5d45744cf57dca2877f60e0c5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6596
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds some additional IDCODEs from the datasheet. It also adds
support for customizing the tap name.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I7cda10b92c229b61836c12cd9ca410de358ede2e
Reviewed-on: https://review.openocd.org/c/openocd/+/6846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Changed flash driver to support writing to the user data page, as well as to any portion of the lockbits page above 512 bytes (the amount used for the actual page lock words). The top part of the lockbits page is used on at least the EFR32xG1 chips for the SiLabs bootloader encryption keys.
As presented to the user, the lockbits page is the same size as the other pages, but any attempt to write to its low 512 bytes is an error. To enforce this, efr32x_write is renamed to efm32x_priv_write and a wrapper function is provided in its place. If the user erases the lockbits page, the driver rewrites the cached lock words after the erase. When the driver erases the lockbits page in order to update the lock words, it first takes a copy of anything stored in the top part of the page, and re-programs it after the erase operation.
There are now multiple instances of flash_bank for each target, and the flash_bank instances must share their cached lock words to operate as intended. Therefore, when a bank is created, the global flash bank list is used to find any other banks that share the same target. Since some banks in the global list are invalid at the time free_driver_priv is called, reference counting is used to decide when to free driver_priv.
To avoid the need to find the lockbits flash_bank from another flash_bank, efm32x_priv_write and efm32x_erase_page now take an absolute address.
There didn't seem to be any reason to prohibit unprotecting individual flash pages, so that limitation is removed from efm32x_protect().
This addresses ticket #185.
Valgrind-clean, except for 2x 4kiB not freed/still reachable blocks that were allocated by libudev.
No new Clang analyzer warnings, no new sanitizer warnings.
Signed-off-by: Doug Brunner <doug.a.brunner@gmail.com>
Change-Id: Ifb22e6149939d893f386706e99b928691ec1d41b
Reviewed-on: https://review.openocd.org/c/openocd/+/6665
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This board is (software wise) similar to the existing SAME54 Xplained
Pro board, with just a slightly different MCU. (Hardware wise, it
features a vastly different form factor.)
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Change-Id: I5e5435d49d333fb74471994ee84de59ed983153c
Reviewed-on: https://review.openocd.org/c/openocd/+/6747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Axel W.
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32mp13x has one core Cortex-A7.
The board Discovery Kit includes an on-board STLink-V3 with SWD
connection.
The webpage of the board is not active yet.
Change-Id: I8836b26612a160ead79766955ebefaf3d21a329c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6675
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
The driver jlink defines the command 'jlink serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: in former code the commands 'jlink serial' and 'jlink usb'
were mutually exclusive; running one of them would invalidate the
effect of a previous execution of the other. The new code gives
priority to 'adapter serial', even if executed before 'jlink usb'.
Change-Id: I920b0c136716f459b6fd6f7da8a01a7fa1ed389f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6656
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The driver xds110 defines the command 'xds110 serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: the original command 'xds110 serial' used a complex and
undocumented conversion of the serial number through multibyte
string, wide-character string and C cast. The XDS110 I can access
and the lsusb dumps available through Google don't show any
exotic USB serial that require such conversion. The original
developer doesn't remember any constraint that mandates such
conversion (see comments in https://review.openocd.org/4322/).
The conversion is removed by this patch.
Change-Id: I38909918079b2c1797ad85ebec2fea1b33743606
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6655
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver kitprog defines the command 'kitprog_serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I844cb815af01137392b6d12e1b5972fc77ac092d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6652
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver ftdi defines the command 'ftdi serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: Ia5b1f325b9fab8f58b5ea70f8b807e50b148b939
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6651
Tested-by: jenkins
The driver cmsis_dap defines the command 'cmsis_dap_serial' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I88e2d4de360a6c6f23529bb18494962a267250df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6649
Tested-by: jenkins
The driver aice defines the command 'aice serial' to specify the
serial string of the adapter, but actually does not use this value
in the code.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I892e0a4e1b41a7a87adf54a5736abf7419f32979
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6648
Tested-by: jenkins
GD32E23x from GigaDevice is cortex-M23 microcontroller and it can work with the stm32f1x driver.
Modifications are similar to this done for GD32F1x0 in #6164 (https://review.openocd.org/c/openocd/+/6164).
Configuration file is added because its cortex-M23 CPU ID is different.
I think that GigaDevice microcontrollers should be handled in an independent unit to separate them from STM32,
but nowadays quick solution is welcome.
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Change-Id: I91f31f5f66808bc50a8f607ac2c107e6b7c5e2b8
Reviewed-on: https://review.openocd.org/c/openocd/+/6527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Freeze the IWDG watchdog when cores are halted to prevent a reset
while debugging.
The PMIC present on some board senses the nsrst and forces a power
cycle to the target. The power cycle causes the SWJ-DP to restart
in JTAG mode. If the debugger is using SWD, the mismatch triggers
an error after the reset command.
Ignore the error detected by 'dap init' and proceed executing the
handler. The error in 'dap init' will force a reconnect during the
following 'dap apid', restoring the SWD functionality.
Change-Id: I04fcda6a5b8a1b080ab4e8890ecd0754d5ed12d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6599
Tested-by: jenkins
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
do not force the presence of the reset line, since some custom boards
may do not contain the reset line.
Change-Id: I031ab34012b34a1b49def9db16461f9de0ae29cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Fleck <fleckz@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/316/
Reviewed-on: https://review.openocd.org/c/openocd/+/6506
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
known boards are NUCLEO-G431KB, NUCLEO-G431RB and NUCLEO-G474RE
note: this work safely with B-G431B-ESC1, B-G474E-DPOW1,
STM32G474E-EVAL and STM32G484E-EVAL
Change-Id: I132a97e1816620b182983edc8a4b272b52b9241d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5484
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G031K8, NUCLEO-G070RB, NUCLEO-G071RB
note: this work safely with STM32G0316-DISCO, STM32G071B-DISCO
and STM32G081B-EVAL
Change-Id: I483b6f44409228cd8c2c97b3c560927d1645c517
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5483
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for ECP5 FPGA targets and board based on this chips:
Radiona ULX3S and Lambdaconcept ECPIX-5
Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6112
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The V3U SoC is unique in that it now has 8x CA76 and CR52,
while the previous SoCs had CA57/CA53/CR7 . This can still
be handled without too complex modifications to the gen3
configuration file, so add the logic to handle it there.
Change-Id: I7ab33eacc1fd379d369988d3d6690d2e82346c7e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On SMP Renesas R-Car Gen2/Gen3 systems, select the boot core as
the default target using the 'targets' command. This way, the
user can start debugging code running on the boot core without
having to switch to the boot core by explicitly invoking 'targets'
command first, since it is likely the debugged code will run on
the boot core. Note that most of the code is already in place, it
was just not used, so this is more of a fix to make the original
intention work.
Change-Id: I727808adce617c1d9ebd6ffa34f60f5882cdae60
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6313
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This file has been added to OpenOCD 0.5.0 in 2011, before gerrit
gets in use, with commit ba71e8c521 ("at91: add chip register
definition and generic init support").
The only procedure in the file has never been referenced in any
other part of OpenOCD. This procedure has syntax errors while uses
its argument 'cs' and several unmatched parenthesis, which clearly
highlights that it has never been used so far.
Gerrit does not report any patch aimed at fixing it.
Even if the file seems unused and could be removed, let's fix it
in the hope it could get used.
While there, remove some useless parenthesis and format it using
the new simplified syntax required by jimtcl 0.81.
Change-Id: Ied26456262e7b99de37667a8ce418f4f12e237bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ba71e8c521 ("at91: add chip register definition and generic init support")
Reviewed-on: http://openocd.zylin.com/6157
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Both http://openocd.zylin.com/542/ and http://openocd.zylin.com/543/
introduce the same typo in the bitfield for initializing the l2
cache of imx53.
One year later, http://openocd.zylin.com/1461/ copy-pastes the same
typo.
The comment above the code show that it's really an error and not
the expected behaviour.
Fix the typo replacing the incorrect comparison '<' with a left
shift.
Change-Id: I43725731a2228e28a676215f76936fa289d9395e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e3b3273433 ("cfg: add imx53loco board config")
Fixes: 108a458ab8 ("cfg: add icnova_imx53_sodimm board config")
Fixes: e608ced330 ("ftdi/board: Add support for DENX M53EVK")
Reviewed-on: http://openocd.zylin.com/6156
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Chip is similar to imx8x series but has different cores at different
addresses.
Support for reduced versions is not yet available.
Tested on imx8qm-mek board
Change-Id: Ia34a80d561ab2849a570d8c375b936a45cbf45ca
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-on: http://openocd.zylin.com/5042
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The Broadcom BCM2711 used in Raspberry Pi 4
No documentation was found on Broadcom website
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711/
Change-Id: I3db6c9af520af8ab4c21ad35ff0f2db28efc0325
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6066
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Broadcom chip used in the Raspberry Pi 2 Model B
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2836
Change-Id: I50b040db213c5b72f63d5f5534c552426c7376f9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6068
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the Broadcom chip used in the Raspberry Pi Model A, B, B+,
the Compute Module, and the Raspberry Pi Zero.
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2835
Change-Id: Ifeb012952473d624327e8c010ac5c886d9473aa0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6067
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Create the TPIU and SWO device in target config file.
Replace the target event 'trace-config' with the TPIU/SWO event
'post-enable'.
Extend the existing code in the event handler to properly set the
gpio mode and speed to permit synchronous trace.
This patch is not exhaustive of all the targets that have SWO, but
has to be considered as an initial example.
Change-Id: If4bbf364c0d2aef3ae49951e76507a3b1cfd58e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5859
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Add board and target configuration files for
Ampere eMAG8180 board and Ampere eMAG processor.
Tested on an Ampere eMAG8180 development platform.
Change-Id: I222653f0fc12d25202a7e469db3594076cbc38ed
Signed-off-by: Anthony Ferranti <ferranti@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5569
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add basic connection details for AM654 and J721E SoCs from TI.
See AM65x Technical Reference Manual (SPRUID7, April 2018)
for further details: https://www.ti.com/lit/pdf/spruid7
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: https://www.ti.com/lit/pdf/spruil1
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Change-Id: Ie5108c6ad6f1304a6bf5b9f81aa9ebd33b8a559d
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: http://openocd.zylin.com/5182
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
TCL expands the variables only if preceded by a dollar sign.
Add the missing dollar before the variable's name '_CPUTAPID'.
Change-Id: Icc5d0dddf24f75d12ee63fee69e1b265e842ca43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Wes Cilldhaire <wes@sol1.com.au>
Fixes: c3166b43e4 ("tcl/target: Add QuickLogic EOS S3 MCU configuration")
Reviewed-on: http://openocd.zylin.com/6079
Tested-by: jenkins
Reviewed-by: TM <tommy_murphy@hotmail.com>
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.
Strip the execution permission.
Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
only core0 is brought up by bootloader
Change-Id: I1d6b5e6ba7498beadbf3805f4271f0197e411bd5
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/5980
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use the board file name as <company>_<name>.cfg
Add the SPDX tag to workaround an error in checkpatch that fails
to recognize as valid a patch that only changes a file name.
Change-Id: I929cd9e5f9fe2e7386950643487534c9a5a05bc6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5931
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
regsub doesn't work correctly on macOS Catalina, which results in
an incorrect CHIPNAME derived from the current target. Since regsub
is only used by this target, replace it with a simple string search
for '.' followed by a substring. This is funcionally equivalent to
what the regular expression was doing, but instead relies in simpler
string operations that should have little to no differences
between systems.
Also, refactor CHIPNAME detection into proc stm32h7x_chipname, so
it's always retrieved in the same way without duplicating the code.
Change-Id: Ia9f63f56b508688e74278b022eaec47e503916e7
Signed-off-by: Alberto Garcia Hierro <alberto@garciahierro.com>
Reviewed-on: http://openocd.zylin.com/5872
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
in RM0399 rev2, there was these bits in DBGMCU_CR registers:
- DBGSTBY_D3 : bit 7
- DBGSTOP_D3 : bit 8
these bits have been changed to reserved in rev3
Change-Id: I9d10d90e383795dc8e25a117d59fa065dc594610
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5861
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In commit a1ce28b118 ("rename some target scripts to be
consistent with the rest") the following renames was applied, but
the old names are still referenced:
tcl/target/{sam7se512.cfg => at91sam7se512.cfg}
tcl/target/{sam7x256.cfg => at91sam7x256.cfg}
Fix the board files to use to correct target config filename.
Change-Id: I7698aa0da7db95c2bd9ba7ab8c260905a975c857
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Nishanth Menon
Tarek BOCHKATI
Sean Anderson
Jacek Wuwer
Hans-Erik Floryd
Doug Brunner
Joerg Wunsch
Antonio Borneo
asier70
Andreas Sandberg
Marc Schink
Wealian Liao
Oleksij Rempel
Ranjith Chandran
Jian-Hong Pan
Matthew Mets
Patrick Stewart
Andreas Fritiofson
Florian Fainelli
Marek Vasut
Rohit Singh
micbis
Olivier DANET
Peter Lawrence
Leonard Crestez
Andrew Wesie
Felipe Balbi
Jiri Kastner
Anthony Ferranti
Tarek BOCHKATI
Andreas Bolsch
Alberto García Hierro
Jonathan McDowell