Flash driver "mini51.c" and "nuc1x.c" are same target MCU.
This patch integrates each driver and functions,
and makes into new "NuMicro" flash driver.
Change-Id: Ifff5c1cfdd265acca0f489631695be9194fa144c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A target config and a simple flash driver for the ADuCM360 microcontroller.
The EEPROM of the chip may be erased and programmed.
Change-Id: Ic2bc2f91ec5b6f72e3976dbe18071f461fe503b8
Signed-off-by: Ivan Buliev <i.buliev@mikrosistemi.com>
Reviewed-on: http://openocd.zylin.com/2787
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
The problem was reported by jstefanop on IRC, the SVF was generated with
Xilinx ISE 14.7.
Found and investigated with Valgrind's vgdb service.
Change-Id: I32b0e77e0380ce4a391661f97449f9c2a5f83625
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2933
Tested-by: jenkins
Currently, the maximum size of a command sent to the TCL server is
4k. This patch increases this limit up to 4M.
Reasoning:
To get high-speed JTAG data transfers, I'm using a very long shift
register. This reduces the overhead of the state changes, as well as the
latency due to the common USB adapter transfers considerably. In order
to submit those long DRSCAN commands to OpenOCD over the TCL/TCL
interface, long TCL command lines are required. This is enabled by this
patch.
v3:
Address review comments. Drop line instead of connection when realloc()
fails.
Changes in v2 of this patch:
The line buffer is allocated dynamically to avoid an OpenOCD memory
overhead if the large buffers are not used. The buffer starts at 4K and
increases exponentially up to 1M, and then linearly in 1M increments up
to 4M.
Change-Id: Iecaef6a56ed5e18e9de4d912a514031ea78fa3bd
Signed-off-by: Philipp Wagner <philipp.wagner@tum.de>
Reviewed-on: http://openocd.zylin.com/2837
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add constant CONNECTION_LIMIT_UNLIMITED which indicates a service
has no connection limit
Change-Id: I008d31264010c25fa44ca74eb6d5740eca38bee1
Signed-off-by: Austin Morton <austinpmorton@gmail.com>
Reviewed-on: http://openocd.zylin.com/2937
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Problem
As my compiler has "warnings being treated as errors" on, it shows the
error message:
error: 'retval' may be used uninitialized in this function
Investigation
Nothing wrong with the logic, 'retval' would have a value before returning.
Just wanna get rid of the compiling "warning as error" message.
Solution
Provide a reasonable default value
Change-Id: I712c15f82819c6c48bee9dceca8de4b18aeb29b0
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2905
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
During reallocation a new memory region might be allocated and the old
one freed. If jtag queue is holding a pointer to the old memory, it will
segfault during the execution. Avoid this by flushing the queue before a
reallocation attempt is made.
This should fix ticket #102.
Change-Id: I737fc3f1ebf6d76413a475beb8bf20184fe0233f
Reported-by: Alex Forencich <aforencich@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2899
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the chip IDs corresponding to the new 5V "SAMC" parts which are
otherwise identical to the SAMD and should work with this driver. Also
add the configurations for their Xplained Pro boards.
Change-Id: Ic268d4ac384a3a77d4211a94da9f9faf4d8c0f7b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2809
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes a warning as reported by the current clang version:
../../../../src/flash/nor/sim3x.c:867:20: error: address of array
'sim3x_info->device_package' will always evaluate to 'true' .
Change-Id: Ie160cbe6df8f491e9beff38d47e2f13575529bf9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2838
Tested-by: jenkins
Reviewed-by: Oleksij Rempel
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only read access to flash chips so is through the target's
memory. Flashes like jtagspi do not expose a memory mapped interface
to the flash. These commands use the flash_driver_read() driver API
directly.
Change-Id: I40b910de650114a3f676507f9f059a234377d862
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2842
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds an option to disable the use of the JSTART instruction
when loading bitstreams to xilinx fpgas. JSTART apparently prevents
configuration if the startup clock is not set to the jtag clock in
the bitstream.
xc3sprog is omitting JSTART for all devices. Problems with loading a bitstream
that does not have StartupClk:JTAGClk are described here:
http://www.xilinx.com/support/answers/56151.html
Change-Id: I8137c0bae05a8c3c6f8e2611869f70a770d1651d
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2860
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The testee target is usefull for certain non-cpu pass-through
situations, for example in the case of a spi flash mapped to the DR of
a JTAG tap, as is the case for most FPGAs with SPI flashs behind them.
We just manage the RUNNING/RESET/HALTED state in the testee driver to
support it being halted which is a requirement for flash banks.
Change-Id: I1b4d52c58a1f6bd753e126bfde74dcc5164d7b69
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2840
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* Add USB VID and PID for the J-Link interface running on the Nordic
Semiconductor nRF51-DK. Also tested with debug out port to debug
external boards.
* Elimiantes need for `-c "jlink pid 0x1015"` on the openocd cmd line.
Change-Id: Ib23acb72b9f5183b76fc7dc22b556982869ae830
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Reviewed-on: http://openocd.zylin.com/2775
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ThreadX uses two stacking schemas on ARM926E-JS, extend API to use more then
one stecking at time.
Change-Id: I92d445ad0981b6409ea4c4e7e438d3a7ae39cbe7
Signed-off-by: Alexander Drozdov <adrozdoff@gmail.com>
Reviewed-on: http://openocd.zylin.com/2848
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
MMU types were checking and installing fakes at init, but this wasn't catching
all devices. Fixes segfaults when attempting mdw and friends on avr.
Change-Id: I5b11f9913157a21f1aeb11ec852f593b529d9be8
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2791
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Even though the latest firmware version for stlink-v1 supports "v2"
JTAG API, the hardware SRST handling is still broken; amend the check
accordingly.
Change-Id: I62c662cd7aa209d2d6e9fe260f5c0be81d0ce672
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2761
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the identifiers to support the flash on the Cypress Type-C Port Controller
chips of the CCG1 family : http://www.cypress.com/ccg1/.
Tested successfully on CYPD1132-16SXI.
Change-Id: I3fe6283379e5bcab964afac31b547ef95535aa2c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://openocd.zylin.com/2757
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The notation Gx0 in the nRF51 Series Compatibility Matrix indicates that
the specified HWID is valid only for build code 0 of each chip, and for
subsequent builds the HWID will be different. Replace the Gx0 notation
with G0 throughout, and add the missing HWID for nRF51422 QFAC A1
(present on the newer nRF51 developer boards).
See: https://www.nordicsemi.com/eng/nordic/download_resource/41917/5/55913589
See: https://devzone.nordicsemi.com/question/30774/mapping-hwid-to-revision-information/
Change-Id: I79d842137d41342db35904867c48b06fbc6fbc70
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2593
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since mqx comes last in the list, with the auto option its
update_threads is called even though it wasn't detected.
This check should be removed from all the rtos helpers and moved to
the generic code, but better do it later all in one go.
Change-Id: If24ab42a58a468d90e9f12028d4c2fb76a9bc2e8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2741
Tested-by: jenkins
It was observed on AM437x that after every reset the target's debug
regions are unpowered. To be able to properly communicate with the
target and perform cortex_a init debug access after a reset event the
examination need to be performed every time, not just on OpenOCD
start.
Change-Id: Idf272e127ee88341e806ee00df154eade573451d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2723
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
After intermittent connection failures or target power failures it
might be necessary to try reexamination even when polling fails. This
should make communication with Cortex-A targets more reliable.
This was runtime tested with stlink attached to an stm32l1 and an FTDI JTAG
adapter attached to an stm32f1 target.
Change-Id: I38c4db8124b7f4bbf53ddda53c13273449f49c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2721
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Färber <afaerber@suse.de>
This adds support for the new Atmel SAML21 family of low-power Cortex
M0+ devices. Their Flash controller is essentially the SAMDxx one so
the change consists of adding the new part IDs. Unfortunately the
device ID logic had a couple of mistakes in it that did not affect
anything on SAMD2x devices (due to 0 values expected there) but that is
a problem on L21, it's therefore addressed here and things should now
match the datasheets.
Tested on Amtel SAML21 Xplained Pro development kit against the included
SAML21J18A there. Also tested for regressions on a SAMD20 and SAMD21
using their dev kits.
Change-Id: I768f75e064b8656c15148730dacaa4c3acfc4101
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2690
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the mandatory Info documentation for the driver as well as
the usage field.
As a clean up, this also includes freeing of the allocated memory
which results in a memory leak if probe is invoked multiple times.
Valgrind-tested.
Reported by Dmitry Shpak.
Change-Id: I2b1d9b9e8b069c6665b11d880b40ce19a1b26ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2694
Tested-by: jenkins
Reviewed-by: Дмитрий Шпак <disona@yandex.ru>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch was tested with an EZR32WG Starter Kit.
Change-Id: I0f7c619e715fe30e88e6da3bead0806dd3bce819
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2700
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Run-time tested with FreeRTOS V8.1.2 (current version).
For the time being I propose this way of dealing with RTOSes that do
not export necessary information on their own.
I also suggest implementing a similar scheme for ChibiOS, exporting
the necessary struct fields' offsets via an OpenOCD-specific helper.
Change-Id: Iacf8b88004d62206215fe80011fd7592438446a3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2347
Tested-by: jenkins
xSuspendedTaskList and xTasksWaitingTermination are only available for
some configurations. Missing optional symbols will have their addresses
remaining at zero so the corresponding lists will be skipped when
building the task list.
Change-Id: If330f5038d009298c3a14a4d2756db7105a30bc8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2425
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a remake of http://openocd.zylin.com/1966
originally written by Angus Gratton <gus@projectgus.com>
ATSAM4L has a "System Manager Access Port" (SMAP) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Without this change any use of sysresetreq or srst locks the chip
in reset state until power is cycled.
A new function smap_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and SMAP reset is released then.
Change-Id: Iad736357b0f551725befa2b9e00f3bc54504f3d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2604
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some targets need arbitrary amount of time (usually not too long)
after reset (both sysresetreq and srst) to do initialisation, and
SWD/JTAG is not available during that. According to PSoC4 docs, the
debugger should try connecting until it succeeds.
Also ahbap_debugport_init might be necessary to perform after using
hardware srst too, so add it there (except for the targets that
support srst_nogate since they are very unlikely to need it).
Change-Id: I3598d5ff7b8e0bf3a5566a57dec4b0b2b243d297
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2601
Tested-by: jenkins
In some cases (the most obvious are TI's SoCs) ROM table lacks entries
for the cores, so OpenOCD has no way to determine what debug base to
use. Due to an error fixed in ec9ccaa288 it wasn't handled properly,
and OpenOCD would continue to try using dbgbase = 0, which happened to
work for e.g. AM437x.
This patch adds a clear indication to the user that to access such a
target, dbgbase must be set manually in the config.
Reported by Felipe Balbi on IRC.
Change-Id: Id8533e708f44b76550eb8b659564f5f45717c298
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2603
Tested-by: jenkins
In some circumstances (e.g. inappropriate jtag clock)
target_write_memory in lpc2000_iap_working_area_init might fail. The
allocated working area should be freed inside
lpc2000_iap_working_area_init in this error case.
This was leading to a weird segfault due to stack corruption later
when reset was executed.
Reported by quitte (Jonas Meyer).
Change-Id: Ia2ed42a9970a4d771727fd516a6eea88e9b859e2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2696
Tested-by: jenkins
Calling ahbap_debugport_init() is wrong here because the actions
performed by it might lead to jtagdp_transaction_endcheck errors thus
leading to infinite recursion.
The removed code is not needed now because target polling should lead
to reexamination automatically, and both cortex_a and cortex_m call
ahbap_debugport_init() as part of their target examine handler.
This was reported as a real life issue on IRC by Weaselweb with
Cortex-A target. Quitte reports similar results in some circumstances
(adapter_khz too high) with LPC17xx.
Change-Id: I7148022f76a1272b5262d251f2e807ffb1543547
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2697
Tested-by: jenkins
The IAP working area needs to be freed here, just like in all the
other driver functions since an automatic local variable is used to
store a pointer to it.
This was reported by quitte (Jonas Meyer) on IRC as a strange totally
unrelated segfault after doing certain operations (leading to target
reset) from GDB. He has provided me with remote access to the specific
machine and configuration that exposed the issue, and after some
debugging it became apparent that a auto local variable (holding the
gdb connection pointer) gets overwritten somehow. Placing an
appropriate breakpoint just before the event and using a watchpoint
made the cause apparent: reset lead to freeing of all working areas,
and there was one holding a pointer to a variable that was auto local
in get_lpc2000_part_id().
Change-Id: I7e634d890135ca0f3b4b311e09e8385a03982bd6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2695
Tested-by: jenkins
This regression was introduced with d90b86d8. "transport select" doesn't
throw an error anymore and autoselects the first available transport on
its own.
Reported by moyix on IRC.
Change-Id: I3f303c0372e915931cca4b28af450694abc1a63e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2693
Tested-by: jenkins
The detection framework assumes rtos->symbols is dynamically allocated,
an assumption that the ChibiOS variant breaks by providing a raw statically
allocated symbol list.
Change-Id: I379bcc2af99006912608ddd3f646ff7085606f47
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-on: http://openocd.zylin.com/2597
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch might influence openocd Tcl commands behaviour in subtle
ways, please give it a nice testing.
The idea is that if an OpenOCD Tcl command returns an error, an
exception is raised, and then the return code is propogated all the
way up (or to the "catch" if present). This allows to detect
"shutdown" which is not actually an error but has to raise an
exception to stop execution of the commands that follow it in the
script.
openocd_thread special-cases shutdown because it should then terminate
OpenOCD with a success error code, unless shutdown was called with an
optional "error" argument which means terminate with a non-zero exit
code.
Change-Id: I7b6fa8a2e24c947dc45d8def0008b4b007c478b3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2600
Tested-by: jenkins
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Commit a35712a85c caused a regression where command
openocd -c "echo a1; shutdown; echo a2"
always returned non-zero exit status to operating system,
even when commands before shutdown all succeeded. This patch
attempt to fix this.
Change-Id: I3f478c2c51d100af810ea0171d2fd4c8fcc657f3
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-on: http://openocd.zylin.com/2589
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Found by clang static checker.
On the very first call of jim_newtap_expected_id() pTap->expected_ids
and expected_len are null, and there's nothing to copy. This patch
changes this cryptic code to use realloc() instead.
Change-Id: Ic0b5140d08257a906f15b55a2ae64db7bc06d5f1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2562
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Tested-by: jenkins
Current flash driver can fail to write across the sector boundary.
This patch fixes "thisrun_bytes" set to "cmd51_dst_boundary" value instead of "cmd51_can_xxxxb"
Referred to SevenW's post and fix,thanks.
http://sourceforge.net/p/openocd/mailman/openocd-devel/thread/fa32e7d6654df22470dc5f4a3dbc984a%40familiebenschop.nl/#msg33594152
Tested on below listed chips.
LPC810,LPC811,LPC812,LPC824,LPC1115,LPC1343,LPC1347,LPC1227,
LPC1769,LPC1788,LPC54102,LPC4088 and LPC2388.
Change-Id: If1c6a1daa58ca27c405bd959a784e599a7a8f4d4
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2607
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The original code had iterated 10,000,000 times and taken the elapsed
time divided by 10,000, to yield kHz which is mathematically correct
only if we were measuring time in seconds, but we are measuring time in
milliseconds, so the correct divisor is actually 10,000,000. Previous
code would report 0.500 for actual measured speed of 500 kHz.
Change-Id: Iba4c4961fe3973e7ccfa6dfa11d606a966ceb50c
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2573
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When the SCTLR has C set but M unset (i.e. Caching on, but MMU off) the cache
if effectively off. So only flush the cache if MMU is on, otherwise stale
entries might be committed to memory.
Change-Id: Iaff8b6f25b7a41ba838b91d45684c98f99fc0b27
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/2429
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Since SWD is currently abusing the JTAG command queue for reset and
sleep handling (and all other operations are performed in a different
way), sleep needs to be forced explicitly to ensure correct timings.
Change-Id: I5b0da6cbb7d0560154e4077b261aa6828cefc892
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2591
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Bug in read pointer check within flash write algorithm made incorrect check
if block size is more than 4 bytes (bug was detected with 16 bytes block size).
Change-Id: I5b8e7ebca619a0a85ae6e9e496ff792248134d81
Signed-off-by: DmitryShpak <disona@yandex.ru>
Reviewed-on: http://openocd.zylin.com/2657
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow most of the existing configurations for older
versions to remain compatible without forcing the user to change his
or her config to explicitly select transport.
Also in some circumstances can remove the need to chain a "-c transport
select X" when building custom configs on the command line, which seems
like a common new user pitfall.
Change-Id: Ic87a38c0b9b88e88fb6d106385efce2f39381d3d
Suggested-by: Petteri Aimonen <jpa@git.mail.kapsi.fi>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2551
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This brings SWD reconnection procedure in line with the ARM
documentation and changes cortex_m reset procedure to make use of it.
The motivation behind this patch is to make SAM4L "reset" and "reset
halt" properly without SRST. The complication here is that EDBG issues
an additional read of DP_RDBUFF automatically right after writing
SYSRESETREQ, that leads to a FAULT which needs to be dealt with
properly. With this patch the very first ahbap_debugport_init DAP
access will make SWD layer properly reinitialise the link before
continuing.
Runtime tested with mbed CMIS-DAP + KL25 only.
Change-Id: Ic506f9db30931dfa60860036b83f73b897975909
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2596
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Valgrind-tested.
Comparison of flashing performance on an FRDM-KL25Z board running mbed
CMSIS-DAP variant, 5MHz clock, old driver:
wrote 28096 bytes from file demo.elf in 26.833590s (1.023 KiB/s)
verified 27264 bytes in 1.754972s (15.171 KiB/s)
this implementation:
wrote 28096 bytes from file demo.elf in 3.691939s (7.432 KiB/s)
verified 27264 bytes in 0.598987s (44.450 KiB/s)
Also tested "Keil ULINK-ME CMSIS-DAP" with an STM32F100 target, 5MHz
clock, results reading from flash, old driver:
dumped 131072 bytes in 98.445305s (1.300 KiB/s)
this implementation:
dumped 131072 bytes in 8.242686s (15.529 KiB/s)
Change-Id: Ic64d3124b1d6cd9dd1016445bb627c71e189ae95
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2356
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many kinetis parts come in multi-bank configuration, so this
optimisation here can't be performed safely.
Investigated and fixed by Richard Braun.
Change-Id: I2b56614b47951595c403a1a8edd3afe11b85679b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2594
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
Avoids "J-Link hw type unknown 0x10" on the Infineon Relax Lite Kit.
Change-Id: I3091623ead2e84b67ac20d9866307ccbb3f26f66
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2568
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Avoids "J-Link hw type unknown 0x11" on various Infineon boards.
Change-Id: If20b9e21110d2acc02be57f5faf28c5e6a39e2c9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2565
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should facilitate dynamic target creation and removal.
Currently it helps with getting 0 bytes lost report from Valgrind on
exit (after talking to a nucleo board). However, 1,223,886 bytes in
5,268 blocks are still reachable which means the app holds pointers to
that data on exit. The majority comes from the jtag command queue,
there're also many blocks from TCL command registration.
Change-Id: I7523234bb90fffd26f7d29cdd7648ddd221d46ab
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2544
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
The target might be using Tcl examine-start and examine-end handlers,
they need to be called when the target gets reexamined after polling
succeeds again.
Change-Id: I371380c6f3c427ec7a0206d73426f6589f18a9bd
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2536
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
This bug was exposed by Valgrind.
Change-Id: I2e2bc036b49ca3ff22f78f765ee4537763350096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2543
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This bug was exposed by Valgrind.
Change-Id: If50878664d928c0a44e309ca1452089c1ac71466
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2542
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Warning, behaviour change: before this patch if a timer callback
returned an error, the other handlers in the list were not called.
This patch fixes two different issues with the way timer callbacks are
called:
1. The function is not designed to be reentrant but a nested call is
possible via: target_handle timer event -> poll -> target events
before/after reexaminantion -> script_command_run ->
target_call_timer_callbacks_now . This patch makes function a no-op
when called recursively;
2. The current code can deal with the case when calling a handler
leads to its removal but not when it leads to removal of the next
callback in the list. This patch defers actual removal to consolidate
it with the calling loop.
These bugs were exposed by Valgrind.
Change-Id: Ia628a744634f5d2911eb329747e826cb9772e789
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2541
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When target was already halted during the initial examination,
arm11_check_init() was trying to read, store and interpret DSCR
contents before the DPM structure is initialised. This caused
a segfault like described on
http://sourceforge.net/apps/trac/openocd/ticket/65 .
This is a totally untested attempt to fix this issue.
Change-Id: I2fff115679a3f0023e7a88c749ccb5f045d6cf01
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2043
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Otherwise it happens if stlink can not be opened on start.
Change-Id: I7088f10e61508dae230eccfe576a51498c92f5b8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2550
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Stian Skjelstad <stian@nixia.no>
This is runtime and valgrind tested with l0, l1 and f3 hla boards.
Change-Id: I49b0b042253d5f3bf216997f0203583db319fe23
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2516
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds the fpv4-sp-d16 registers to the armv7m register set.
The work is inspired by Mathias K but takes a different approach:
instead of having both double and single presicion registers in the
cache this patch works only with the doubles and counts on GDB to
split the data in halves whenever needed.
Tested with HLA only (on an STM32F334 disco board).
Currently this patch makes all ARMv7-M targets report an FPU-enabled
target description to GDB. It shouldn't harm if the user is not trying
to access non-existing FPU. However, the plan is to make this depend
on actual FPU presence later.
Change-Id: Ifcc72c80ef745230c42e4dc3995f792753fc4e7a
Signed-off-by: Mathias K <kesmtp@freenet.de>
[fercerpav@gmail.com: rework to fit target description framework]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/514
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by clang static checker.
Change-Id: I77b0dc18188328fdb28d07b9e5c52e06182d9e2b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2561
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by clang static checker.
Change-Id: Ifa58ba383092341c7343916e5cc8ec3c72ab2f60
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2560
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Found by clang static code checker.
Change-Id: Ic1370f8d7a48f08da6514afec5aacde38af7dfb6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2559
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ARMv7E-M (CortexM4) architecture
- fix position offset of r2,r3 registers on exception stack
- switch 'calloc' arguments
- remove prototypes of internal function and typedefs
- add NULL check for alloc functions
- remove last line of license "Franklin Street, Fifth Floor"
because of 'checkpatch' validation
- environment: jlink + twrk60n512
Change-Id: I70840ded15b17dd945ca190ce31e2775078da2d9
Signed-off-by: Marian Cingel <cingel.marian@gmail.com>
Reviewed-on: http://openocd.zylin.com/2353
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the at90usb128 flash (tested on the RZUSBstick)
Change-Id: Ic042d7c403b20a5cc533da00c30ae6e2139bbd10
Signed-off-by: Olivier Esver <olg.esver@gmail.com>
Reviewed-on: http://openocd.zylin.com/2557
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Solution found on the internet
Change-Id: Ied6f7d9b28131a7ac83b203e4c64d4e9ffec0595
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/2496
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Failed build on Mac OS X 10.10.2 was reported in OpenOCD-devel.
Cleaning types and printf formats. uint32_t prefered for flash/sector sizes.
2 minor changes in comments.
Removed redundant bracket.
Change-Id: Ia06b77af59c2c0ffd10869a4b263a760ca8b0a7a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2558
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Added new entries to the nrf51_known_devices_table array. New entries
are documented in the "nRF51 Series Compatability Matrix V1.0" found on
the Nordic Semi web site. Reordered entries to match the order found in
the document.
Also added an entry for an undocumented hwid discovered while flashing
the PCA10031 and PCA10028 dev boards.
Change-Id: Icca7da103d437dc28e651f27ab937fe953b9aac9
Signed-off-by: Theodore A. Roth <troth@openavr.org>
Reviewed-on: http://openocd.zylin.com/2514
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Given that the manual states that these two subcommands are
deprecated and were scheduled to be removed back in 2010,
remove them and the corresponding documentation from the
manual.
Change-Id: Iaac633349d7fcb8b7f964109c7d26dd0cc5fc233
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1860
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Based on the initial work on bcm2835gpio.c by Paul Fertser with many
additions. Modifications to the GPIO handling was minimal in this
patch. A more big modification is required before cleanup the
interface between bitbang and sysfsgpio.
Change-Id: I54bf2a2aa2ca059368b0e0e105dff6084b73d624
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is based on the initial work by Paul Fertser with addition of the
switch sequences and new ACK handling. In case of WAIT response, the
sticky bits are cleared and the last operation is repeated. The ACK
handling is based on the interpretation of the 8 February 2006 ARM
Debug Interface v5 Architecture Specification
Change-Id: Id50855b1ffff310177ccf9883dc9eb0d1b4458c8
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Reviewed-on: http://openocd.zylin.com/2437
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I couldn't make OpenOCD to work with GDB. I was always getting this in GDB:
(gdb) target remote localhost:3333
Remote debugging using localhost:3333
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Malformed response to offset query, timeout
(gdb)
While debugging gdb remote protocol, I have seen that gdb responds with:
w ++$?#3f
And those two '+' seems to confuse the OpenOCD parser, if it sees another
'+' sign it emits the DEBUG output and sets the noack_mode to 2. The
problem is that we weren't even IN noack mode, this was set to 0 and then
it explicitly sets it to 2 and thus turning the noack mode on.
Change-Id: If267c9226e57fa83121ded09cf69829f8f0b4b93
Signed-off-by: Matej Kupljen <matej.kupljen@gmail.com>
Reviewed-on: http://openocd.zylin.com/2545
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Without this patch, to perform a memory read, OpenOCD first issues an
LDC instruction into DBGITR in Stall mode (thus executing the
instruction), then switches to Fast mode and reads from DBGDTRTX once
for each word to transfer.
At the very end of the transfer, the final Fast mode read of DBGDTRTX
has, as always, the side effect of re-issuing the LDC instruction. This
causes two problems:
(1) If the word immediately beyond the end of the requested region is
inaccessible, this spurious LDC will cause a fault. On a fast CPU, the
LDC will finish executing by the time the poll of DSCR takes place,
failing the entire memory read. On a slow CPU, the LDC might finish
executing later, leaving an unexpected and confusing sticky fault lying
around for the next operation to see.
(2) If the LDC succeeds, it will leave the loaded word in DBGDTRTX, thus
setting DBGDSCR.TXFULL=1. The cortex_a_read_apb_ab_memory routine
completes without consuming that last word, thus confusing the next
routine that tries to use DBGDTRTX (this may not have any visible effect
on some implementations, because writing to DBGDTRTXint when TXFULL=1 is
defined as Unpredictable, but I believe it caused a visible problem for
me).
With this patch, the bulk mem_ap_sel_read_buf_noincr is modified to omit
the last word of the block. The second-to-last read of DBGDTRTX by that
function will cause the issue of the LDC for the last word. After
switching back to Normal mode and waiting for that instruction to
finish, do a final read of DBGDTRTX to extract the last word into the
buffer, leaving TXFULL=0.
Without this patch, memory accesses are always expanded such that they
are aligned to the access size. With this patch, accesses are issued
exactly as ordered by the caller. The caller is expected to handle
fragments at the beginning and end of the transfer if the address is
unaligned and an unaligned access is not desired.
Without this patch, the DFAR and DFSR registers, which report the
location and status of data faults, are ignored while performing memory
accesses, which could cause problems debugging an OS page fault handler.
With this patch, DFAR and DFSR are preserved across memory accesses, and
DFSR is decoded in the event of a synchronous fault to provide the
caller with more information about the reason for failure.
Thanks to Boris Brezillon for the original patch whose ideas led to the
non-word access mechanism implemented here and to various code reviewers
for their comments.
Change-Id: I11ae7104fbe69a522efadefc705c9a217a7eef41
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/2381
Tested-by: jenkins
Reviewed-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
RM0038 Rev.12 lists these new parts and introduces the category naming
scheme.
RM0367 Rev.2 (STM32L0x3 RM) doesn't add any new codes.
Change-Id: Id95dd48dda64d5f108dac57d265d29a7db3a1bd1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2495
Tested-by: jenkins
OpenOCD's SWD subsystem doesn't currently have a consistent WAIT
handling (i.e. it doesn't ever retry, just returns an error), so right
after a row write a small delay is needed as AHB access is stalled
during the flashing operation.
The issue was exposed with a samd20 using ftdi SWD transport.
Change-Id: I07d99d3a96845cc689c3904a41f4d41344f200aa
Signed-off-by: Andrej Kazmin <funnyfish@funnyfish.botik.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2268
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This optional argument tells OpenOCD to exit after finishing (either
succesfully, or with an error) the programming sequence. Without it
OpenOCD stays running.
Change-Id: I6ecaf33ff985eea9a9cd02ff644a74403ae3e1e5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2492
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently
openocd -c "echo a1; shutdown; echo a2"
outputs both "a1" and "a2" and only then shuts down. This patch fixes
it by making shutdown command throw an exception, so unless it's
caught the shutdown will behave as expected.
Change-Id: I764268b3a9046ff3e9717d04095ea0673f1d755a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2511
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Convert the DWT register store to use a byte array and fix the byte order
bug uncovered by that. Also fix an incorrect access of the PC value.
Change-Id: Idb5acab71bdf5a96895c358324b05c335e4d32ca
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2476
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The registers are represented as bit arrays intended to be accessed using
the buf_set_* and buf_get_* functions. Storing the register values in
integers enables accessing them directly, which gives different results
depending on host byte order.
Convert the register store to use a byte array instead and fix all the
byte order bugs uncovered by that.
Also merge the 32 and 64 bit register fields. Only one of them is used at
a time and after the change to byte arrays their types are also the same.
Change-Id: I456869a1737f4b4f5e8ecbfc1c63c49a75d21619
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2475
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
On armv7 there no longer are 1kB pages. Instead the bit that in
older architectures distinguished 1kB pages from 4kB pages is on
armv7 used for as execute-never marker. There may now also be 16MB
supersections with 40 bit physical address.
Change-Id: I959bdb8012782a9d07d968907a21f50e3d9b356a
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-on: http://openocd.zylin.com/2386
Tested-by: jenkins
Reviewed-by: Vladimir Svoboda <ze.vlad@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add Cortex-A5 identification to ROM-table display, and also
to cortex_a_init_debug_access. This change is mostly cosmetic.
Change-Id: I7b1dd8755d70d45eb5f315aa1918d44a813b3cdf
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/2483
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The image struct is malloc'd and hence base_address_set doesn't have a
defined value.
Caught by Valgrind.
Change-Id: Ice15b2299fc768e44e8034eeb93e035076eacd03
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2524
Tested-by: jenkins
Reviewed-by: Stian Skjelstad <stian@nixia.no>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After profiling gmon.out was being written in little endian format only
which would cause gprof to issue and error and exit on big endian targets.
Change-Id: I526a40adae0f9a439fc5b77cef30fda228198b48
Signed-off-by: Jose de Sousa <jose.t.de.sousa@gmail.com>
Reviewed-on: http://openocd.zylin.com/2168
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I53568674951ec8a5db5e191c7b50c60b5a84d0b6
Signed-off-by: Michael Brown <fractalmbrown@gmail.com>
Reviewed-on: http://openocd.zylin.com/2463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit 832f0a5bfb 'stm32: add mass erase support for STM32L' added
use of mass-erase in-place of bank-erase. This is triggered if first
bank is requested to be fully erased.
This erroneous action completely fails on STM32L162VEY (has 512 KiB
flash in two 256 KiB banks) and also unintently destroying contents of
EEPROM and second flash bank.
Change-Id: I0f13f7b0346747a09c755d72b5b95775ceff5a6f
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Reviewed-on: http://openocd.zylin.com/2441
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Topaz reports on http://sourceforge.net/p/openocd/tickets/87/ that
protection level constants are mixed up. This leads to device ending
up in protection level 1 after mass erase.
Additional work is required to actually put the device in RDP Level 1
and then back to Level 0, as Option bootloader launch is a special
kind of full target reset.
To be able to flash properly after mass_erase a "reset init" is needed
(it's anyway recommended to always perform it before any flash
operation).
Change-Id: I9a838909458039bb0114d3019723bf134fa4d7c9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2490
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This macro makes windows builds faster and helps with the old "#define
interface struct" issue as the word "interface" is part of libusb-0.1
API. However, defining it in replacements.h is too late, as windows.h
gets included by that time from somewhere else.
This solution is provided by Ray Donnelly from the MSYS2 team.
Change-Id: I376a5fb3d106786515d7e1ba44dbd751e4dcdb1b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2486
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since libusb-0.1 might be provided by libusb-compat, it will depend on
libusb-1.0, so needs to be mentioned before it in the link command
line, this is relevant for static linking.
Thanks go to mingwandroid for spotting it during MSYS2 build.
Change-Id: I15cf0b8f084c351b4f93e75686bd0f843477352b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2485
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the new STM32F446 mcu with 512 Ko
Tested with a eval board
Change-Id: I0c16ce7d32d249c7634d697815207c20e7f778c4
Signed-off-by: prudhomme.remi@gmail.com
Reviewed-on: http://openocd.zylin.com/2484
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The message as it was didn't let the user know that something was wrong
with the target or wiring.
Change-Id: Ib609c2d31959e77413e61c348d0e31d7269d5c58
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Jens Bauer <jens@gpio.dk>
Also remove an unrelated no-op cast.
Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2473
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This helps to uncover incorrect usage when a pointer to uint32_t is
passed to those functions which leads to subtle bugs on BE systems.
The reason is that it's normally assumed that any uint32_t variable
holds its value in host byte order, but using but_set_u32 on it
silently does implicit pointer conversion to (void *) and the
assumption ends up broken without any indication.
Change-Id: I48ffd190583d8aa32ec1fef8f1cdc0b4184e4546
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Do not use buf_set_u32 on integers; they're not buffers.
If using buf_set_u32 on integers, bytes will be exchanged on Big Endian targets.
In this particular case, FLASH_OPTCR was incorrectly written, causing it to often
contain one of these values: 0x00aaaae1, 0x00aaffef, 0x00ffabe1 or 0x00abffe1.
This write-protected the device before flash-programming, causing this command...
flash write_image erase unlock myfile.elf
... to fail, complaining about write-protection.
Repeating the above command would change the OPTCR register each time.
After applying this patch, the OPTCR remains "unchanged".
Change-Id: I73d510fcc2e81a01973ad5c6e1aa22715ebd2743
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2466
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Mass erase operation might be impacted by different factors,
apparently the most reliable way is to do it while asserting the chip
reset line.
Change-Id: Id6ab57eaec86e402ffdf4f5c8843e7735640f03e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2424
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Enable auto-creating additional discovered TAPs even if some TAPs are
predefined, avoiding initialization failure when it's not necessary.
Also, drop the arbitrary limit on the number of predefined TAPs. Still,
don't auto-create any if there are more than 20 TAPs already, to stop
a noisy connection from creating unlimited TAPs.
Create auto-probed TAPs with less noise.
Reduce code duplication between verification and auto-probing.
Change-Id: I82a504d92dbcc0060206e71f10c5158256b5f561
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The default label does just return the same error code as the case for
zero, so this can be handled by a simple if statement.
Change-Id: I61a8cb51b5e261f21eca386af7d8cbf17ffa2d44
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/2430
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the serial wasn't actually used in hid_open() call,
which meant that the first device with matching vid:pid was opened
irrespective of the actual serial number.
Change-Id: I45216ae5d9e0798e97be693c30e2f03c89b9a02b
Signed-off-by: Jaakko Kukkohovi <jkukkohovi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2487
Tested-by: jenkins
Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As of RM0091, Rev. 7, all F0 have the same revisioning scheme.
Change-Id: I0b344a1d3ca3f61f48fa151e83c549ca5333ae47
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2457
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The ability to change the speed has been added to firmware versions J22 and
above. Any attempt to change on earlier versions will be ignored without error,
as the existing code does.
For supported firmware versions the driver will attempt to get as close as
possible to supported speeds (never higher).
The default stlink speed on power up is 1.8MHz.
The driver will now also print supported clocl speeds during init.
Change-Id: Iee9bd018bb8b6f94672a12538912d41c23d48a7e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2335
Tested-by: jenkins
As a note we need to cache the requested speed setting, as the
hla interface may not be ready when the first adapter_khz is called.
Change-Id: I2fa6807d5f0bd3f0365cf178bd10a230c39415a7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2334
Tested-by: jenkins
Output a similar message to what we have on low-level JTAG adapters to
avoid confusing users. Reported on IRC by chickensk.
Change-Id: I96d58410ef715b966e32d79c0aacf38596c5eb3f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2451
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Previously the jtag_add_reset(1, 0) caused the processor to be released,
and if SRSTn existed then it would then be reset again two lines later.
Change-Id: I58b7a12607f46f83caa7ed3b3cebc4195eb51ef6
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/2398
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds flash programming support for LPC5410x and LPC82x.
And adds auto flash size detection for LPC800 series.
Tested on below listed boards/chips.
LPC54102(LPCLPC54102Xpresso)
LPC824(LPCXpresso824-MAX)
LPC812(LPC812MAX)
LPC811,LPC810
Change-Id: Ie68b6d425b17ccfa83814607ee61056e99800c1c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2442
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
A7 MPCore needs unlocking the debug registers same as with A15 MPCore.
Found out by hacking on the code.
Change-Id: I613cb4fb35007b85b4a9a401577b47768bc1a08b
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-on: http://openocd.zylin.com/2344
Tested-by: jenkins
Reviewed-by: Kamal Dasu <kamal.dasu@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Added Cortex-A15 support for DAP AHB-AP init code as per ADI V5 spec.
Also added changes to make the APB MEM-AP to work with A15.
Made the the cortex_a target code generic to work with A8, A9
and A15 single core or multicore implementation. Added armv7a code
for os_border calculation to work for known A8, A9 and A15
platforms based on the ARM DDI 0344H, ARM DDI 0407F, ARM DDI 0406C
ARMV7A architecture docs.
Change-Id: Ib2803ab62588bf40f1ae4b9192b619af31525a1a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1601
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When no transport is selected, the error message dumps the available
transports, but not how to actually select one.
Change-Id: I63da2a4b59e3f6cc8d30bd631e41a82636a056ef
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For example "bp 0x20000000 8 2" makes openocd segfaulting on a
stm32f4x Discovery board.
Change-Id: I1ddd46b1fa9ade78db2234ed975ccefb72539331
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/2342
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GCC-4.2 on Mac/PPC complains about size_t is expected for %zx and the build stops.
In order to avoid other problems, I've chosen simply to typecast.
Change-Id: I99b569c4d1100e729712e31d24d6539f8b5971b6
Signed-off-by: Jens Bauer <jens@gpio.dk>
Reviewed-on: http://openocd.zylin.com/2360
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When communication with target fails for whatever reason, it makes
sense to do JTAG-to-SWD (in case the target got power-cycled or the
DAP method was reset anyhow), SWD line reset sequence (part of
JTAG-to-SWD already) and the mandatory IDCODE read. Schedule that to
be performed on the next poll.
Fix the return values for ftdi and jlink drivers to be consistent with
OpenOCD error codes and remove ad-hoc calls to perform DAP method
switching (as it's now done from the upper layer automatically).
Change-Id: Ie18797d4ce7ac43d8249f8f81f1064a2424e02be
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2371
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mateusz Manowiecki <segmentation@fault.pl>
When a target was present on OpenOCD start but later disappeared for
whatever reason (typically unstable connection or target going to
sleep) and reappeared only for a brief period of time, reexamination
would fail, and poll would no longer run. This patch fixes it.
Change-Id: I61f9b5a3f366a761320e233f4e1689f926b5556d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2370
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The IAP firmware won't return a proper status with some versions. This
happens on my CCC r0ket board and others have seen it as well [1]. So
just ignore the status code and do a (weak) consistency check instead.
[1] http://www.lpcware.com/content/forum/lpc1343-iap-read-part-identification-command
Change-Id: I0daa779d520a540629677c56857bbc20d6db422d
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Reviewed-on: http://openocd.zylin.com/2364
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The FSF address has changed; The FSF site says that
address is
Free Software Foundation
51 Franklin Street, Fifth Floor
Boston, MA 02110-1301
USA
(see http://www.fsf.org/about/contact/)
Instead of updating it each time the address changes,
just drop it completely treewide.
Change-Id: I27199f7625901f677d8105d1e8876cff00147b71
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2340
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When an enabled FPU is detected we now use an appropriate stacking.
Change-Id: I1b0f43ec22e1c55c4f10e2ffa97d4aaa77bca5ee
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/2354
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In ChibiOS/RT 3.0 the ready list pointer "rlist" is now part of the system
data structure. Since the ready list is the first element in that
structure it can be accessed via the structure's symbol "ch".
Change-Id: Idc7eaa87cb7bbad0afa0ff1dafd54283bf429766
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/2352
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
is_erased can be one of -1, 0, or 1 so it must not be checked like a
boolean value. In this case we want to erase a page unless we know it's
already erased so we just check for is_erased != 1.
Thanks to Jim Paris for pointing this out on another driver.
Change-Id: I4591186228153b64e5a9608a2aac18745e578d4a
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2368
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some J-Link fw versions require registration to be performed before
SWD operation is possible. It doesn't harm anyway, vendor's utilities
do it unconditionally.
Thanks go to Segger for providing the necessary information.
Change-Id: Iabd76c743eca86e2c817a97cb93c969fec3f7ac6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2331
Tested-by: jenkins
Added the chip definition for the Atmel AT91SAM4S4A. This chip is a 48-pin
package with 256k flash and 64k ram.
Change-Id: I8ada7d5735e31e0ce086f96f5906c7358464245c
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2254
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After SPI flash was written by the assembly language stub,
the last SPI command was not terminated by raising CS.
This left the SPI device in a hung state that prevented the
flash from being read by the M4 SPIFI controller, even after
the M4 was fully reset. To access the flash via SPIFI, it was
necessary to completely power cycle the board.
This fix adds the missing instructions to raise CS and
terminate the SPI command after the last byte. This allows
the M4 to be resumed or reset cleanly after flashing. The
SPIFI memory is now immediately accessable at address
0x1400 0000 after flashing is complete.
Change-Id: I4d5e03bded0fa00c430c2991f182dc18611d5f48
Signed-off-by: Anders <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2359
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds flash programming support for LPC1547/8/9 and LPC1517/8/9.
Tested on LPC1549(LPC1549 LPCXpresso Board with CMSIS-DAP firmware).
Change-Id: Ic95b4d62055bb9fdc2ca484696a38ccaf49ad951
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2304
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Grigori G <greg@chown.ath.cx>
is_erased can take the value 0 (no), 1 (yes), or -1 (unknown).
Checks like (!is_erased) don't do the right thing if it's -1.
Change-Id: I10ba32c99494ca803e0a7a1ba56fdd78184b96bb
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2366
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the UICR is already empty, there's no reason to return an error
just because it can't be erased again. This happens, for example,
when flashing UICR from GDB after a "monitor nrf51 mass_erase".
Change-Id: Ia6d28c43189205fb5a7120b1c7312e45eb32edb7
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2363
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
nrf51_erase_page() checks for (sector->offset == NRF51_UICR_BASE) to
determine if the UICR should be erased. However, sector->offset for
the UICR bank is set to 0 in nrf51_probe, so this code is never hit.
Attempting to erase UICR ends up erasing the first flash sector.
Use bank->base instead to determine if UICR is being erased.
Change-Id: Ie5df0f9732f23662085ae2b713d64968cd801472
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2362
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The UICR region is actually 0x100 bytes in size. Besides making the
full region accessible, having the right value is important because
GDB rounds flash addresses to the nearest multiple of the block size
when determing which flash blocks to erase.
Change-Id: I416c391cbfc7be41a03a9b9c6e42326c87391f38
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2361
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
added "Single Wire Output" and "Trace Memory Controller" peripheral
IDs to dap_rom_display(), which is invoked by the "dap info" command
Change-Id: Iea3201007bb98e6376fbb50be40a4a2e031b0a03
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
In preparation for adding serial number support.
Change-Id: I3c9fb411b79d54a4d2de067039255436ba6708c7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2328
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The mass erase for STM32L was lack because the procedure is more complex
than the procedure for the STM32F4xx.
The reference manual RM0038 (L100 subfamily) page 79 is more accurate
than the reference manual for the STM32L0xx. On the L0, the mass-erase
erase also the EEPROM. This is a limit to mass erase on L0.
The mass erase procedure is a command of telnet interface.
Tested on Discovery L053 and Discovery L100.
Change-Id: I6a1d7a3669789aea89c59a006ab2d883f3d827ca
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2319
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should make protection work as expected on all stellaris
families, including the latest Tiva C Snowflake.
Run-time tested on TM4C123x (Blizzard).
Change-Id: Ia017edb119bec32382b08fc037b5bbc02dd9000c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2267
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This introduces a new common function that allows auto-discovery of a
suitable USB interface based on class, subclass and protocol
matching. It claims the interface and returns the corresponding
endpoints number to the caller.
The need for this arised due to nRF51822 USB dongle which comes with
an "on-board Segger J-link debugger" having 3 interfaces, so the
current code can't work at all with it (in this particular case the
last interface needs to be choosen). This also removes special
handling of JLink-OB endpoint numbers as it's now possible to
autodetect them as well as the standard JLink endpoints.
Change-Id: I4d990a7a3b373efdd2949a394b32d855a168e138
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2327
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is still limited to pre-Snowflake parts and the first 64K of
flash.
Change-Id: I9ca872ada3d1a87dba6261464b2a72a15eda5ecf
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2264
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
TI's ICDI adapter supports some additional commands which a user might
want to run for debugging or other purposes, the most useful of them
being "debug unlock" that fully mass-erases the device and unprotects
the flash.
Change-Id: I26990e736094367f92106fa891e9bb8fb0382efb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2263
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change 2288 fixed the extraneous reset caused by set_configuration that
crashed the LPC Link-2 running JLink firmware and works on windows platforms.
On Linux however, conditional code was still calling USB reset and caused
the adapter to crash on any non-windows platforms.
Change-Id: Ibf2a02d0dcdd91ccb71d86231cd8311dcadfee1e
Signed-off-by: anders@openpuma.org
Reviewed-on: http://openocd.zylin.com/2297
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to [1], we shouldn't reselect an already active configuration to avoid needless device reset. This is known to cause issues with e.g. LPC Link2 with JLink firmware.
[1] http://libusb.sourceforge.net/api-1.0/caveats.html#configsel
Change-Id: I3568ada77780a521548c450090db7173f8d0b2dd
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Anders Oleson <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2288
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
There were two problems with the _protect() feature:
1. The address written was off by a factor of two because the address
register takes 16-bit rather than 8-bit addresses. As a result the
wrong sectors were (un)protected with the protect command. This has
been fixed.
2. The protection settings issued via the lock or unlock region commands
don't persist after reset. Making them persist requires modifying the
LOCK bits in the User Row using the infrastructure described below.
The Atmel SAMD2x MCUs provide a User Row (the size of which is one
page). This contains a few settings that users may wish to modify from
the debugger, especially during production. This change adds commands
to inspect and set:
- EEPROM size, the size in bytes of the emulated EEPROM region of the
Flash.
- Bootloader size, the size in bytes of the protected "boot" section of
the Flash.
This is done by a careful read-modify-write of the special User Row
page, avoiding erasing when possible and disallowing the changing of
documented reserved bits. The Atmel SAMD20 datasheet was used for bit
positions and descriptions, size tables, etc. and testing was done on a
SAMD20 Xplained Pro board.
It's technically possible to store arbitrary user data (ex: serial
numbers, MAC addresses, etc) in the remaining portion of the User Row
page (that is, beyond the first 64 bits of it). The infrastructure used
by the eeprom and bootloader commands can be used to access this as
well, and this seems safer than exposing the User Row as a normal Flash
sector that openocd understands due to the delicate nature of some of
the data stored there.
Change-Id: I29ca1bdbdc7884bc0ba0ad18af1b6bab78c7ad38
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2326
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reference code for the SAMD2x disables caching in the NVM controller when
issuing NVM commands. Let's do this as well to be consistent and safer.
Add a "chip-erase" for the Atmel SAMD targets that issues a complete Chip Erase
via the Device Service Unit (DSU). This can be used to "unlock" or otherwise
unbrick a chip that can't be halted or inspected, allowing the user to reflash
with new firmware.
Add a "set-security" command which issues an SSB. Once that's done and the
device is power-cycled, the flash cannot be written to until a "chip-erase" is
issued. The chip-erase cannot be issued by openocd at this time because
the device will not respond to a request for the DAP IDCODE.
Change-Id: I80122f0bbf7e3aedffe052c1e77d69dc2dba25ed
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2239
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When looking for a debug base address of a core, one should search
through all the ROM tables, not just the top-level one.
This code also assumes that the first found entry (in a depth-first
search) will correspond to core 0, the second to core 1 etc.
The patch is supposed to be an alternative implementation of
http://openocd.zylin.com/#/c/1313/.
Change-Id: Ifc88971a02fe3d9c00d9bf72a822ade5804d4e09
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1920
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This allows GDB to automatically switch to the thread that has
been interrupted and show you where it has stopped.
Change-Id: Icb9500dc42a61eb977e9fac55ce9503c9926bf5d
Signed-off-by: Jon Burgess <jburgess777@gmail.com>
Reviewed-on: http://openocd.zylin.com/2303
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Versaloon firmware has been updated for reporting
errors if fail on swd transactions.
Change-Id: I49ac0ad034cc9ad83cc4e43953579811d1243063
Signed-off-by: Simon Qian <openocd@versaloon.com>
Reviewed-on: http://openocd.zylin.com/2302
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the user executes a command with an invalid subcommand, the error
message is extremely unhelpful:
> flash write test.elf
flash write test.elf: command requires more arguments
This is because any command line that starts with a valid command group is
classified as a group, triggering ocd_bouncer to print the confusing
message.
Fix by requiring that to be a command group, the command line must not
contain any unknown tokens after the last valid (sub-)command group. That
is OK because command groups don't have handlers defined and thus can't
take any parameters.
Also fix the error message for "unknown" type to be similar to the error
message that is printed (by Jim) for non-existent primary commands.
Change-Id: I26950349f0909fd3961c4f9ab9b198c221cea9fc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2285
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added calls to libusb_error_name() where applicable in order to easier
understand the error messages.
Change-Id: I3fe3d4b5624ae0de37c36e54a371eba5535ccaa1
Signed-off-by: Joakim Gebart <joakim.gebart@eistec.se>
Reviewed-on: http://openocd.zylin.com/2289
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Previous to this version the code of handle_flash_probe_command would
probe a bank twice: first time by auto-probe through a call to
flash_command_get_bank and second time by calling the probe function
directly. This change adds a flash_command_get_bank_maybe_probe wich
is a more generic version of the flash_command_get_bank, that would
allow commands to decide whether auto-probing should be performed or
not.
Change-Id: If150ca9c169ffe05e8c7eba36338d333360811e3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2093
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code treats registers that are shadowed in FIQ mode in a special
way: to read them out the target is first switches to USR mode. But
since USR != ANY the current implementation later skips register read,
and the loop becomes endless in case any !valid ARM_MODE_ANY is
present at the moment arm_dpm_full_context() is called. This was
reported in https://sourceforge.net/p/openocd/tickets/76/. The issue
surfaced because 2efb1f14f6 added two
ARM_MODE_ANY registers ("sp" and "lr") which were not normally read,
so at the time a user was calling "arm reg" they were not valid.
Fix this by changing the mode appropriately while keeping the "mode"
variable state intact so it would later match register's mode.
Compile-tested only.
Change-Id: I01840e8fa20ec392220138a3f1497ac25deb080a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for QSPI flash controller driver for
Marvell's Wireless Microcontroller platform.
For more information please refer,
https://origin-www.marvell.com/microcontrollers/wi-fi-microcontroller-platform/
Following things have been tested on 88MC200 (Winbond W25Q80BV flash chip):
1. Flash sector level erase
2. Flash chip erase
3. Flash write in normal SPI mode
4. Flash fill (write and verify) in normal SPI mode
Change-Id: If4414ae3f77ff170b84e426a35b66c44590c5e06
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Reviewed-on: http://openocd.zylin.com/2280
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new FL1-K family is replacing the FL-K family. The data from all
three was based on the datasheet. In addition the 8MB S25FL164K was
tested successfully with OpenOCD on a custom board.
Change-Id: Idafeed86da12a481c0db92cc0de7ba28f50c2252
Signed-off-by: Anders <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2281
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's possible for us to fail to read the part ID code so make sure that
part_info is initialized to NULL before attempting to do so, otherwise
we could proceed and use it uninitialized and then segfault.
Change-Id: I0a3f3d3947690b66f0981b5046340449521e0b33
Signed-off-by: Jack Peel <jack.peel@synapse.com>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2276
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Luckily, TI's website has predictable URLs for the datasheets, so it
was trivial to download all the pdfs corresponding to the currently
available 71 TivaC devices. Then they were processed with pdftotext
and parsed by this script:
BEGIN { capture = -1 }
/^Device Identification 0 \(DID0\)$/ { state = "waitingclass0" }
/^Device Identification 1 \(DID1\)$/ { state = "waitingpartno0" }
/^CLASS$/ { if (state == "waitingclass0") state = "waitingclass"
else if (state == "waitingclass") capture = 4 }
/^PARTNO$/ { if (state == "waitingpartno0") state = "waitingpartno"
else if (state == "waitingpartno") capture = 4 }
(FNR == 3) { family = $2 }
{
if (capture >= 0) {
if (capture == 0) {
if (state == "waitingclass")
class = $0
else if (state == "waitingpartno")
partno = $0
}
capture--
}
}
END { print "{" class ", " partno ", \"" family "\"}," }
Change-Id: I6820c409fe535f08394c203276b5af4406fe8b92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2262
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should make current Tiva C parts usable apart from the protection.
Runtime tested on TM4C123GXL (Blizzard) and TM4C1294XL (Snowflake).
Change-Id: Ia64e9d39fbd2b7049578bbfade72435e5203ddf5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2257
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This struct and libusb_get_device_descriptor() method are not present
in libusb-0.1 API, so when libusb-1.0 is unavailable, this code breaks
the build. Fix by using the appropriate struct (which is apparently
filled automatically on device initialisation).
While at it, change return values for consistency with the callers.
Change-Id: I7d85ab9a70401a155a65122397008ae4d81382fe
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2252
Tested-by: jenkins
Reviewed-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When SWD mode is not supported by the target adapter, the call should
return an error instead of segfaulting.
Change-Id: I1626097deb93ecfbe78a6e82d812c7a673dbbde5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2256
Tested-by: jenkins
Commit f701c0cb seems to have introduced a regression for non-JTAG
transports as the newly created "tap" (DAP actually) ended up being
disabled, thus resulting in total lack of functionality.
This was exposed by a debug log demonstrating ftdi SWD transport
connection to mdr32f9q2i, the target wasn't examined on init and
couldn't be reset.
Change-Id: If53cbe800d4adc177aa3ac3219860e7fa15b3e49
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2261
Tested-by: jenkins
Reviewed-by: Angus Gratton <gus@projectgus.com>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This was very helpful when debugging programs during async loading.
Change-Id: Ia2eacc3e105403f70f51b1242b675e2ffe86e8ca
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds initial support for the STM32L0 family, specifically the ID
code 417 variant. The 'L0 has 128B rather than 256B pages as well as a
different number of pages per sector. It also has several key registers
and register sets in different locations from the STM32L1xx parts.
This change therefore takes the opportunity to reorganize part information into
a const table (it was previously determined by a set of control statements) and
abstracts away some of the low-level details to make them generic for L1 and
L0 parts.
We also include the first bank's size (for dual bank parts) in the new
device information table (and correct that size for the 0x437 variant
which is 256 rather than 192KB).
The 'L0 parts will not use the built-in loader/helper for Flash writing.
Tested on STM32L053 (dicovery board and Nucleo board) and STM32L152
(discovery board).
Change-Id: I57f7a8ab02caee266de71b31ae82a50d85728a0b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This was somehow missed in the chip ID table and of course that's
exactly the one on my board (as such, tested on hardware).
Change-Id: I212d7c729d979e0357f1d4635f40935e25fe6ff3
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2260
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fitted to various Analog Devices ADuCM36x dev boards.
Change-Id: Ib3691704c0ecd2f8cba1abba284aee695d6bc135
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2244
Tested-by: jenkins
As Daniel pointed out, since the rewrite of the USB Blaster driver, the
initialization behaviour has change. The initial flush of the FIFOs is
not longer done with a specific USB setup packet, but with a write
filling up the blaster queues.
The problem is, quoting Daniel :
When the CPLD is in bit banging mode (as is usually the case), the
first 0x00 byte sets all pins to low and disables the output
driver. Disabling the output drivers is a few nanoseconds slower
than changing a pin from high to low, so I see a spike towards GND
on my reset line when that byte is sent over USB. The spike is too
short to have an effect on the board.
When the 4096 0x00 bytes are processed and the TMS=1 is to be
generated, all I see is several microseconds of low level on all
pins, resetting my board.
This patch changes the way the initialization is done :
- at driver init, nothing is sent towards the usb-blaster
This gives time for init script to setup PIN6 and PIN8 (resets)
- at the very first driver command, the initialization is done :
- the output is in bit bigbang mode
- the PIN6 and PIN8 are computed according to init script
- the 4096 computed output is sent
Change-Id: If7ceee957f6b59bcb27c8f912f1cfdd0f94f75ed
Reported-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-on: http://openocd.zylin.com/2229
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Daniel Glöckner <daniel-gl@gmx.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even though changing transport is impossible, reselecting it should be
harmless.
Change-Id: I6c1c2786134e826f47f848b590e6d712b6fd2206
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2251
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
EJTAG v2.0 indicated some debug caps in IMP register.
V2.6 moved them to DCR register. To make it more universal,
convert this values and store them for later use.
Change-Id: Id6b9f47c9c2ea94d37281ebfcae5acf357261ddf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1932
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
and make version specific debug log
Change-Id: I17f7ff757cfa1264a1dadbfe20c5e21de62ef87a
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In particular -f and -s options may contains paths that can easily
exceed the (old) 128 bytes buffer.
Change-Id: Ifc198536549f50663e8e588519bb9ef75dcd172c
Signed-off-by: Cristian Maglie <c.maglie@bug.st>
Reviewed-on: http://openocd.zylin.com/2241
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- stlink_usb_get_rw_status() had a bug where FAULT or WAIT responses
in read/write operations were ignored, leading to incomplete data.
- Added wrapper stlink_cmd_allow_retry to handle
SWD_AP_WAIT/SWD_DP_WAIT statuses in most commands. These statuses
appear if an SWD read or write received a WAIT ACK response from the
target more than 4 times in a row. The driver retries the operation
(with exponential backoff) before failing outright (in testing 1
retry was always enough.)
- As part of the implementation of stlink_cmd_allow_retry a large
number of lines of boilerplate were refactored.
- Fleshed out stlink_usb_error_check and added it to some more code
paths so WAIT or FAULT responses are logged to debug. WAIT responses
will be logged even if they are subsequently retried, which should
help in case the retries have subtle side effects (none
anticipated.)
Tested with two targets: STLINK F0 Discovery, Nordic NRF51822. Only
tested with STLINK V2 programmers.
Change-Id: I9af24e8f0121b035356dbb9978d6bbf4feb2e4d3
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2201
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Previously the -irlen parameter was required even though it is not
a part of the SWD or CMSIS-DAP transports.
This may eventually need to be changed for CMSIS-DAP once that
supports JTAG as well.
Change-Id: Ia02b67840c19c7cf1c7a75063648c0174176a311
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2226
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This workaround broke usage with at least the I.MX6Q.
The comment implies that talking to the J-Link dongle itself should
fail if the target isn't reset, which sounds really strange. I'm
guessing it just triggered another bug in OpenOCD or Segger FW which
might have been fixed since. Revert and wait and see if there are any
failure reports.
Tested with Kwikstik (J-Link + Kinetis K40), not with the mentioned
adapter.
Change-Id: I97f555efe079bd99c098bf483491d9509b2363ad
Signed-off-by: Roy Spliet <rspliet@mpi-sws.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2147
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
During the initialisation a driver might need to communicate with the
target (e.g. sending jtag2swd sequence), so when doing so it should
honour the user-specified speed.
Change-Id: If84fea6057fda9edcf2c0a653edfbab2500e3cdd
[andrew.smirnov@gmail.com: fix khz/hz confusion]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2224
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Don't hardcode the type for the array, just output the array initializer
so the includer can choose the type and storage class, zero-terminate at
will and so on.
Change-Id: I6d5e0710eaaba0a218b3eb32f6569177356f4462
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2176
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Using custom build-time tools is always more problematic, especially
for cross-compiling.
This alternative implementation assumes "od" (IEEE Std 1003.1-2001)
and sed are available which should be the case for any reasonably
modern system.
Change-Id: I0208f475648c78e7dca127ff4bab60d314b2bf53
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2139
Tested-by: jenkins
Reviewed-by: Fatih Aşıcı <fatih.asici@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The Atmel SAMR21 is a Atmel SAMD21 with an Atmel RF233 in one package (two
dies). Tested with the SAMR21 Xplained Pro eval kit.
Change-Id: I1d79ea05834b925d7ec810527206fe86854e684b
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2194
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Even if it does not return, the initialization will be failed.
But it is better to show why the error is caused.
Change-Id: I399c7c94a7156be22723a9715e594061bb414a7e
Signed-off-by: Masaki Muranaka <monaka@monami-ya.com>
Reviewed-on: http://openocd.zylin.com/2189
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If load_image address overlap with fast_data_area,
it will caouse different mysterius issues. This patch
should prevent it.
Change-Id: Ibc95e5aa3ac002a59755029496b6a72616e9287f
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1854
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis-K series has ID:0x001C0000 on MDM-AP IDR register.
Other Kinetis(L/M/V/E) series have ID:0x001C0020.
Change-Id: Iada37038cd239f7331ba80a3673b36bf7e18c555
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2195
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A previous commit changes the target name used by tcl scripts.
commit d9ba56c295
target: rename cortex_a8 to cortex_a
The current change renames target functions and definitions in the
implementation from cortex_a8 to cortex_a.
This prepares the implementation to support Cortex-A8, A9, A15-MPCore
in one place.
Change-Id: I73b5a38a92c12ba5bd3b806fbbb664817575a6d7
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1599
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with stm32f1x, stm32f4x and kl25 targets using SWD transport.
Change-Id: I118d07371b53f402ea9ac73f874460a309c05100
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1947
Tested-by: jenkins
ftime() is deprecated by POSIX.1-2008 and causes a warning on
FreeBSD.
The generic OpenOCD LOG_DEBUG implementation already outputs time of
an event with a millisecond precision.
Change-Id: Ic8e4ea27c268f07554ba519768b9bdfc4343f3e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2187
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This fixes the issue of improper initialisation sequence and in
particular makes "cmsis_dap_vid_pid" config specification functional.
Not really elegant but it's in line with the ftdi driver and so can be
reworked in a uniform way later when the internal API is changed.
Change-Id: Ief9fc64ad0ac24e1c66727153f383e4f30a830c7
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2192
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is intended to fix cmsis_dap_vid_pid command but it doesn't
because cmsis-dap has only one transport and it's auto-selected from
"interface" command handler (before any other commands are run) and as
the result cmsis_dap_usb_open() is called too early.
Change-Id: Idaade73797d8df67a6439d096f6abc9736495599
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2191
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added Openocd commandline argument to ignore_error when the
read back TDO does not match to expected value specified with
TDO after masking with what is specified in MASK. This allows
to continue to play entire SVF file ignoring errors.
Error logs clearly show the failure reason and prints
read back TDO value.
Change-Id: I324f476fc16a003b35e6f2c5b63976431f49d54a
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/2129
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If the current reset_config doesn't specify availability of nTRST or
nSRST, just leave them alone, do not try to deassert them ever
(asserting would be prevented by the upper layer).
Change-Id: I90123c666e05a1c26f1e164625e82d766a3e3744
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2186
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Use a special signal instead of a dedicated swd mask. Amend
jtag-lock-pick_tiny_2 config accordingly.
Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2183
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Unfortunately, this means they're available for config files only
after selecting swd transport.
Change-Id: Ia2afc1f3bfdba8d81efbb8ab964b174c0f7e2811
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2182
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds -alias|-nalias options to ftdi_layout_signal command that
allow to declare a new signal based on an already defined one.
Change-Id: I552578ebcd12ae21957a1c0d3b7e878adeff6df0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2181
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I looked through all the target configs after stripping comments and
such from them with sed to see what jtag-specific commands can appear
first, and it looks like all the meaningful combinations should be
covered.
Change-Id: I8d543407b7f4ac8aca7354ecd50e841c8a04d5f3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2179
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Polling was disabled based on global variables jtag_trst and jtag_srst
which were never touched in non-JTAG mode. Modify the check and remove
the ugly workaround to avoid calls to a possibly uninitialized JTAG
subsystem.
Change-Id: I3b18c81e0fba7aaf35afe6f08c3fe8fa6f8443fd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2143
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is usable on most or all FTDI adapters using a small hardware tweak.
TCK goes to SWCLK as expected. TDO should be wired to SWDIO. For TDI there
are two options:
Either add a 74HC126 or similar tri-state buffer between TDI and SWDIO,
with OE controlled by a signal named SWDIO_OE. Or simply connect TDI and
SWDIO together via a suitable resistor (220-470 ohms or so depending on
the drive capability of the target and adapter).
nSRST (and of course Vcc, GND) may be connected too but all other signals
should be NC.
Change-Id: Id36cf4577439be96bd4e5955c3026236e1cabced
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1958
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also align them with spaces instead of tabs.
Change-Id: I1c01412a3ea77b29e8e133f5c92d05ed79d7c0f3
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2133
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
ARM deprecated other trn periods in ADIv5.1 and one cycle is the only
setting that is guaranteed to be implemented, as well as being the reset
value in ADIv5.0.
Thus it makes no sense supporting anything else.
Change-Id: Iffa16bb0ce74788bca88fd3ace8a026148013d00
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2132
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Name of the function is already a part of the LOG_DEBUG macro, so
there's no need to include it in the string itself.
Change-Id: I18c3d5b746e9106d55104e490ccf5bc5e85cc380
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2138
Tested-by: jenkins
SAM4L requires additional steps to be taken right after SYSRESETREQ is
issued in order to function robustly:
- CMSIS-DAP DAP driver needs to explicitly check for sticky bit
errors since it is possible for adapter to perform successful
write opration, report no errors and then, under the hood, do
some other things that will result in sticky bit being set.
- Debugger needs to wait for security system to finish
intialization and assert CDBGPWRUPACK before proceeding
This change is related to commit http://openocd.zylin.com/#/c/1995/
Change-Id: I741c95a809bfd60d930cec9482239e4796a62326
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2088
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
We don't need to do full blown AP ABORT in case of CMSIS-DAP errors,
and the code that was in place was not doing that(issuing AP ABORT)
anyway.
Change-Id: Ide83b1f8875d725da6cb0d53aae8229f8c6316b3
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2112
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
This should no longer be needed after tcl scripts are fixed to avoid
calling jtag subcommands when jtag is not used.
Barely tested with an frdm board.
Change-Id: I75f02b088e6134562ae634417d97c48e377df6e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2130
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It could be reused by SWD drivers and in other places.
Change-Id: Ieed0cf70c111a73d3a42ed59f46a0cdd177a73d5
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1957
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Swd_queue_ap_abort should set DAPABORT, not only clear sticky errors.
However, DAPABORT should not be set as soon as there is a single
FAULT/WAIT response. It's an "emergency only" operations for use only when
the AP have stalled the transfer for a long time. So these need to be
separate functions.
Change-Id: I37618447884faad54d846c2b07fa668ad505919d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1956
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
These features are not currently used so remove or disable them before
something starts to. Not having them around simplifies redesign of the
APIs.
Change-Id: Iad25cc71c48b68a1fa71558141bf14d5ab20d659
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1955
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Increases performance by a factor of two for long reads.
Change-Id: I81a7a83835058560c6a53a43c3cc991100f01766
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1954
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Otherwise it breaks SWD targets. The check seems really weird anyway since
it loops through *all* TAPs after the ADIv5 target but doesn't do anything
at all with the result, other than not setting the return values despite
returning ERROR_OK.
Remove a bogus initialization that was needed because of the odd
behaviour of this routine when an IDCODE wasn't found.
Change-Id: Ic086352f6af868b3406b00420291a0a671e3acac
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1953
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix bug in parity calculation macro.
Cache and update the selected DP bank when necessary.
Add aborts when the Ack code signals a failure (we should really only
clear the sticky bits, but this will do for now).
Change-Id: I38a4da136ba1d9e989b33c1875a80c0b1b2be874
Signed-off-by: Fatih Aşıcı <fatih.asici@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1950
Tested-by: jenkins
The JLink protocol description doesn't really specify it for
JTAG-level commands but the real life evidence is that 0x01 error code
means "Adaptive clocking timeout" as it does for e.g. WRITE_MEM_ARM79.
Change-Id: I4e3b568742814271919f92d202713968c8fcccfb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2169
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add part IDs for the new SAMD10 and SAMD11 parts within the Atmel SAMD
family, they have the same Flash controller as the other samd parts and
should be supported by the at91samd driver. Compile-tested only.
Change-Id: I493ae96a7d7e8d19e607fd9a4b6544a982be42b3
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2170
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
while investigating coresight components, i've found some new partnumbers and devtypes.
Change-Id: Ie68032b0b21d542c2084f80db38b06f5cd4c7591
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/2166
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The error message (with the usage field unpopulated) looks like this,
obviously missing at least a space before Usage:
Error: 'fm3' driver rejected flash bank at 0x00000000Usage (null)
Change-Id: I2a625676e784d02942823f972a201f7f4f810c68
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2161
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This results in a 90% speedup on USB-Blaster, which serializes repeated
TDI input against TDO readback; program time on an 5CGXFC5C6F27 part was
dropped from 2m30s to 9s.
Signed-off-by: Joshua Wise <joshua@joshuawise.com>
Change-Id: I92d5a8b800492283d619328549235b610528c338
Reviewed-on: http://openocd.zylin.com/2145
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On a processor with caches, when you write data to memory OpenOCD invalidates
the cache lines affected. If you write to an address within 64 bytes of
UINT32_MAX, then the for loop control variable wrapped around resulting in an
infinite loop. Change control variable to be an offset from the address
involved. We should never be asked to write 2^32 bytes, so wraparound should
not be a problem.
Change-Id: Ibfe654113eff71684862ff651e7a1cd05ccc6760
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2126
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
HLAs do not provide direct DAP access, so the best we can do about it
is skipping it.
Change-Id: I877ef8fd2d86e40e7442a637cdba182cfd60e05a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2173
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
We don't need to swap the endianness in the target generic code.
This swap is necessary because of the adv_debug_if debug unit.
This patch moves this specific piece of code from or1k.c to
or1k_du_adv.c.
Change-Id: I3acea092fe6edfa79b4a87861b5f01204f071bf0
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1663
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Adds support for auto-probing on devices which support the IAP
Read Part ID command. Includes IDs for all LPC17XX, LPC13XX,
LPC11XX and LPC11XXX devices with publicly available user
manuals.
To use auto-probing, select the 'auto' lpc2000 variant.
Change-Id: Ic617c32925c9ebe0e9d9192ed8ddbfa08e9f0aaa
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2075
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
LPC11(x)xx and LPC13xx devices are mostly compatible with the lpc1700
variant of the LPC2000 driver, but use a fixed flash sector size of 4KB.
Change-Id: I033515f4ff6bc61d3b9babd27096f78c99cea927
Signed-off-by: Cosmin Gorgovan <cosmin@linux-geek.org>
Reviewed-on: http://openocd.zylin.com/2071
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
stm32x_write_options is locking the FLASH_OPTCR register by
writing 0x00000001 to it, which clears the other bits. This
causes problems with subsequent flash operations; the hardware
is probably seeing the write protection bits in the register
set to '0' (protect), causing a WRPERR.
This patch ORs the value of the register with 0x00000001, so that
the only change is the lock bit itself.
Change-Id: I0e3ca9aa6563ce1b57a01fc0faf7563b6b85f620
Signed-off-by: Elliott Partridge <elliott.partridge@gmail.com>
Reviewed-on: http://openocd.zylin.com/2155
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ARMv7-R cores are largely uniprocessor-configured, and when they are
multiprocessor-configured the format of the MPIDR register isn't
compatible with ARMv7-A cores.
Change-Id: I024ec514496fbab5075c6fb34b6acd870e68e1fc
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2096
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Configuration commands assume the last created target is the one they
should be applied to. An example of this is sourcing an stm32f1.cfg
several times to access several microcontrollers on the same JTAG chain
where cortex_m reset_config should apply to the target that was just
created, not to the first one.
This fixes http://sourceforge.net/p/openocd/tickets/71/ .
Change-Id: I1ca41cc05fe5f36c4bc62dde4614da1405754fd8
Reported-by: Michael Eischer <mieischer@users.sf.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2142
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the communication with the target was failing (either because of an
intermittent connection or the target was rebooted), this is needed to
reestablish operational state.
Reported-by: Tim Sander <tim@krieglstein.org>
Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I91ea2e2b2b5ef8eb27dfe9bae95ef2a919f67e4e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2152
Tested-by: jenkins
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If polling was failing, it likely meant that either the target was
disconnected or rebooted. In the latter case it needs to be reexamined
to be properly configured for the debug session, so do it just in
case.
Reported-by: Tim Sander <tim@krieglstein.org>
Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I5b067c18d9276d4e86cc59739f196ae7d0931622
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2151
Tested-by: jenkins
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move logging for cmsis_dap_queue_ap_read/write to happen after a call
to cmsis_dap_ap_q_bankselect so that that SWD operation would appear
in the log in the same sequence they happen on the bus.
Change-Id: Ic046bc753e661da7924b019c9100d6932fb686bf
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2087
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Previous to this commit 'ahbap_debugport_init' would ignore if timeout
happened or not when waiting for CDBGPWRUPACK and CSYSPWRUPACK and would
continue initialization regardless. It also would not reset the
timeout counter after finishing polling for CDBGPWRUPACK and starting
for CSYSPWRUPACK which could potentially cause some problems.
Also refactor code of both snippets into a more generic function to
avoid duplication.
Change-Id: I16e4f50e6819e08c4126e71ef8cec7db559d608e
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2086
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Fix for LOG format specifiers, this is a superset of those
exposed by the arm-none-eabi build.
Add 0x prefix for all values printed in hex.
Add LOG messages for error cases when enabling or disabling
paging.
Change-Id: I070c556e0ad31204231a2b572e7b93af22a9bc61
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2149
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The spifi_init_code blob is calling the spifi_init() function from the ROM.
This ROM function is making use of the stack. So if the stack pointer is
invalid, trying to execute this code leads to a double fault and the
target_run_algorithm() call return with an error.
This patch simply ensure that the stack pointer is properly setup before
calling the spifi_init() ROM function.
Change-Id: I42a2163cfc2c6dfe5ada97ae8eb2bb6d2e283ff7
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/1836
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b
Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is only the basic code proposed for mips32_pracc_exec() function.
It checks every pracc address against the expected address when
reading (instruction fetch).
The code expects to start at PRACC_TEXT and any subsequent read address
is obtained by adding 4 to the previous one.
After shifting out all the instructions the code executes a final check.
It checks now for the first pass trough PRACC_TEXT and shift out
only NOP instructions.
A mips core does not need an additional NOP and after the first check
it exits if there is no store access pending.
After shifting out one NOP the core must be reading at pracc text or the
code exits with error.
The code continues shifting out NOPs until all store accesses have
been performed.
After shifting out 10 NOPs it exits with error.
No assumption is made about the number of store instruction shifted out or
the ordering of the store accesses. It only checks that the number of
store accesses is the same as the number of store instructions at dmseg
after execution.
mips32_pracc_read_ctrl_addr() and mips32_pracc_finish() are added to
simpify a bit the code. Fields pa_ctrl and pa_addr are added
in ejtag_info for storing values of pracc control and address.
Change-Id: If6322d5c8cbeadcd4acd3972c0f72c8490f53c34
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1827
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is the first patch intended to make a more precise pracc check
when running in legacy mode (code executed by mips32_pracc_exec()).
It only makes some cleanups, mostly due to unnecessary code.
With the last cache optimizations for processor access (pa for short)
all the pracc functions generate the code following some rules that
make pa more easily to check:
There are no load instructions from dmseg. All the read pas are
instruction fetches. PARAM_IN related stuff is not needed.
Registers are restored either from COP0 DeSave or from ejtag
info fields. PRACC_STACK related stuff is not needed any more.
The code starts execution at PRACC_TEXT and there are no branch or jump
instruction in the code, apart from the last jump to PRACC_TEXT.
The fetch address is ever known.
For every store instruction to dmseg the function code sets
the address of the write/store pa.
The address of every store pa is known.
Current code ends execution when reading a second pass through PRACC_TEXT.
This approach has same inconveniences:
If the code starts in the delay slot of a jump it makes a jump
to PRACC_TEXT after executing the first instruction. A second pass
through PRACC_TEXt is read and the function exits without any warning.
This seems to occur sometimes when a 24kc core is halted in the delay
slot of a branch.
If a debug mode exception is triggered during the execution of a
function the core restarts execution at PRACC_TEXT. Again the function
exits without any warning.
If for whatever reason the core starts fetching at an unexpected
address the code now sends a jump instruction to PRACC_TEXT, but due
to the delay slot the core continues fetching at whatever address + 4
and a second jump instruction will be send for execution. The result
of a jump instruction in the delay slot of another jump is
UNPREDICTABLE. It may work as expected (ar7241), or let the core in
the delay slot of a jump to PRACC_TEXT for example. This means the
function called next may also fail (pic32mx).
Change-Id: I9516a5146ee9c8c694d741331edc7daec9bde4e3
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1825
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Near all pracc functions store $15 in DeSave and
restore it when exiting.
There is no need to save it, if mips32_pracc_read_regs()
save this register in Desave when entering debug mode.
mips32_pracc_write_regs() needs to update it when
exiting debug mode.
Other pracc functions must not modify DeSave.
The jump code in the fastdata transfer function needs also
some little modifications.
Remark:
Like in current code the user can read/modify $15
with the cp0 31 commands.
Change-Id: I5b7dfc1b6169da846f5d2dd3ad4209a9da2c3fad
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1565
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently the code is loaded calling mips32_pracc_write_mem_generic().
Cache synchronization is not performed.
If configured as write back cache there is no chance to execute the
handler. If configured as write through cache and the cache
lines written to are not cache resident (I-side cache miss) may work.
The patch makes possible to execute the handler in a cached active
memory segment (mainly from KSEG0), but nothing else. The data
is still loaded without performing cache synchronization, code loaded
may not be executable.
Performance may not be faster. At start, for example, the code resides in
main memory, not in cache, and the core must transfer code from
memory. We can really modify the code to force a wait for the first
transfer like we do with start and end addresses, making sure the code
is cache resident for the rest of the queued transfers.
This can also may happen if we execute code (greater than the I cache size)
and the handler code is evicted from the cache.
Code tested on ar7241.
Change-Id: Iffdb4dae108b872fef0e7bacc5ea99649cdc1630
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1564
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Currently the functions mips32_checksum_memory() and mips32_blank_check_memory()
load the code word by word.
The bug in cache code is a good reason for doing so.
If there is no other reason we can load the code as a buffer to save time.
mips_m4k_write_memory() expect a buffer in target endianness, this is done by
target_buffer_set_u32_array().
Cleaned up exit code.
Tested on ar7241 big endian and pic32mx little endian with verify_image.
Flash erase check only tested in pic32mx.
Change-Id: Ib63ed98732b2e23b058e7349a0a57934b7604905
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1562
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Follows the the same rules of optimization used by all pracc functions.
Solves some bugs in previous code and adds support for write through caches.
Change-Id: If88c6738ca8c8197f327f22b766120a24f71b567
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1557
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is a post-release version but hopefully some fixes that went in
are worth it; also the changes here make OpenOCD compatible with stock
0.75 version if a distro maintainer decides to use it.
Change-Id: I7ad1814c7c4868198475cdca4750c3d0ee4f5f8b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2121
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Only send the new I/O state for the bytes that changed.
Change-Id: I930edc9518e6019331e68e4756acc5e92dda25a4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1999
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added SVF_BUF_LOG macro to properly print the hex buffer of parsed
string for SIR, SDR, TDI, TDO and MASK. The original debug and error
logs with respect to printing real values were misleading and also
had endianess issues. All the bits are printed now instead of just
u32 values.
Change-Id: Ie89902403bdb61ff458418446c2ca1253ea2a63f
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1964
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
As exposed by arm-none-eabi build, fix the wrong modifiers.
Change-Id: Ia6ce7c5c1d40e95059525c3e5d81b752df2fea7c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2122
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paging checking and disabling wasn't present for IO r/w,
so the commands were successful only when paging wasn't
enabled (e.g. EFI boot phase).
Change-Id: I41366c0fadff3ea1eb8a153291f20a46cd9ddec1
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2118
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
On larger FPGAs the default buffer size is not nearly enough;
automatically reallocate it as needed.
Change-Id: Ic8071e8cceddeef897ce76996c029250fd22662b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2099
Tested-by: jenkins
Reviewed-by: Kenneth Lorthioir <ibelimb@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Since c6216201b2 gdb target description
generation support is enabled by default and it counts on checking
"feature" pointer in reg_list. Both mips32 and dsp563xx neither used
calloc nor explicitly set feature (as it was a newly introduced struct
field).
This patch changes all targets to use calloc for consistency.
Change-Id: I9eceadef8b04aacb108e24ae23cb51ca3009586f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2102
Tested-by: jenkins
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Different *nix systems use different constants, so sizeof should be
used instead. This fixes the build on OS X (as sun_path length is
hardcoded to 104 on Darwin).
Change-Id: I1df611383dedcfc6d153ec59b453a895c7d84e94
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2095
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
According to the "Arm Arch Ref Manual ARMv7-a and ARMv7-R edition" the
CPSR encoding for Monitor mode is 0b10110 (22) not 0b11010 (26) as is
currently used.
Change-Id: I73373a0029a81abc92febf518b88bf0dd4dec1fa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2081
Reviewed-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Tested-by: jenkins
Reviewed-by: Younes REGAIEG <y.regaieg@gmail.com>
Reviewed-by: Tim Sander <tim@krieglstein.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If gdb was disconnected by the moment the target entered halted state,
update_halt_gdb would segfault.
Change-Id: I67477e9199c1df097be83a49e38602f975c083f5
Reported-by: Younes REGAIEG <younes.regaieg@imag.fr>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Those are breaking the build with clang 3.4 (current default compiler
on OS X 10.9.2).
Change-Id: I9f2fbfbb6d544498cb8d6a62565e4ebe7223e784
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2077
Tested-by: jenkins
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
Apparently this helper was never actually used, and current clang
produces an unused const variable warning, so it's breaking the build.
Change-Id: Ib088bef5e9c0a48942c1d417d46f738469ee7e28
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2076
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Some fixes to 'samd_protect' including:
- Fix a bug in which the value of 'set' parameter passed into the
function was ignored so it was impossible to remove flash
protection once it was set.
- Check the protection status of the sector via 'is_protected'
field of the corresponding 'flash_sector' structure to see if
any actual HW manipulations needs to be done.
- Change the way the errors during protection activation are
handled. Now even in the case of error in the middle of
protecting a number of sectors the subroutine would still update
the state of the sector protection in sectors array so as to
avoid cases where openocd thinks that the sector is not protected
while it actually is.
Change-Id: I4cc6445a98ec13bdd94c89f0711c17840738a215
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2027
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Bail early if trying to erase protected sector and also do not double-erase already
erased sectors.
Change-Id: Ic2d39af48c3b8e10e78d52dd978b9bc01f671c6a
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2026
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Bail early if trying to write to protected sector also mark the sector
we are writing to as dirty.
Change-Id: I892f83461792e1cc2dcccade7aa65717831a6805
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2025
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Remove 'first' and 'last' checks in 'samd_protect' since those
parameters are checked in 'handle_flash_erase_command'.
Change-Id: I30e5598a9ab656d81055f26cc63e291377605300
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2024
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
COMMAND_PARSE_NUMBER may return, thus any memory allocated may not be
freed, simple reorder fixes the issue.
Change-Id: I0ce444a5b032f5c49b6d33a03a8c0b71cad49c8c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2065
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GPL requires providing sources for any derived work. I do not see any
reason to not include the xscale stuff into release tarballs.
Wildcard matching is used because plain directory name matches
implicit rule for executables and xscale.c built is errorneously
attempted, and directory name with a slash duplicates a directory
(xscale/xscale) in dist.
Change-Id: Ie0266470dcb97be87a09ba2dda9b3957f7cbc2fa
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1911
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
GPL requires providing sources for any derived work. I do not see any
reason to not include the rlink stuff into release tarballs.
Change-Id: I686ab88994030312aca5bdfe731a72f10803b5c3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1907
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems that when xml register support was added the rtos code was not
updated to match. This then caused gdb to return the following error when
rtos support was enabled - "Remote 'g' packet reply is too long".
Change-Id: I7429c4b1efed120e2e690678d55f3d6e87ee1ff1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2054
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
nRF51 doesn't have any sort of flash page cache so we need to write
all of the data on the word-by-word basis and poll for "Flash Ready"
bit each time.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I8caffbf69ebf9a69915724704ddbe270d1bb8d92
Reviewed-on: http://openocd.zylin.com/2050
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
SoftDevice stack ihex binary, provided by Nordic expects being able to
write data necessary for its correct operation at the adresses inside UICR.
This patch exposes UICR region of flash as a second bank on the MCU to
facilitate that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Idbc140b8de027f60655f78043877b7c054eb06f9
Reviewed-on: http://openocd.zylin.com/2013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Nemui Trinomius
Ivan Buliev
Paul Fertser
Philipp Wagner
Austin Morton
Alamy Liu
Evan Hunter
Christoph Pittracher
Andrey Yurovsky
Robert Jordens
Kyle Manna
Alexander Drozdov
Karl Palsson
Vincent Palatin
Peter A. Bigot
Simon Qian
Uwe Bonnes
Marc Schink
Spencer Oliver
Andreas Fritiofson
Tomas Vanek
Richard Braun
Juha Niskanen
Patrick Noffke
Ed Beroset
Uwe Kleine-König
DmitryShpak
Mateusz Manowiecki
Mahavir Jain
Angus Gratton
Andreas Färber
Franck Jullien
pierre Kuo
Marian Cingel
Olivier Esver
Theodore A. Roth
dmitry pervushin
Robert P. J. Day
Jean-Christian de Rivaz
Matej Kupljen
Christopher Head
Andrej Kazmin
Antony Pavlov
Andreas Bomholtz
Daniel Glöckner
Joerg Fischer
Olivier Schonken
Jose de Sousa
Pawel Si
Michael Brown
Jussi Kivilinna
Rémi PRUD’HOMME
Jens Bauer
Jaakko Kukkohovi
Jörg Wunsch
Alexander Stein
Kamal Dasu
Salvador Arroyo
Grigori Goronzy
Christian Gudrian
Thomas Schmid
Anders
Jim Paris
Peter Lawrence
Jon Burgess
Joakim Gebart
Andrey Smirnov
Austin Phillips
Andrey Skvortsov
Robert Jarzmik
Oleksij Rempel
Cristian Maglie
Masaki Muranaka
Fatih Aşıcı
Kamal Dasu
Mathias K
Jiri Kastner
Joshua Wise
Seth LaForge
Marco Cruz
Cosmin Gorgovan
Elliott Partridge
Alex Ray
Ivan De Cesaris
Aurelien Jacobs
Tim Sander
Karl Hammar