This emulation mode supports software translation of an AP request
into an address mapped transaction that does not rely on physical AP
hardware. This is necessary in some hardware such as K3 SoCs since the
hardware architecture anticipates a potential race condition between
AP doing direct memory access generating transactions back to system
bus and firewalls that data path out.
This emulation mode allows direct memory driver to emulate CoreSight
Access Port (AP) and reuse the SoC configuration meant for JTAG
debuggers.
Since the address ranges are flat in nature, the requisite memory base
and size will need to be provided a-priori to the driver for mapping.
The other design alternative would be to map requested memory map for
every register operation, but, that would defeat our intent of getting
max debug performance.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I2d3c5f7833f1973e90b4f6b247827f62fc2905d0
Reviewed-on: https://review.openocd.org/c/openocd/+/7089
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Direct memory driver support for CoreSight Access Port(AP).
Even though we emulate SWD (serial wire debug), we aren't actually
using swd. Instead, we are using a direct memory access to get to the
register set. This is similar in approach to other fast access native
drivers such as am335xgpio drivers.
Example operation on Texas Instrument's AM62x K3 SoC:
+-----------+
| OpenOCD | SoC mem map
| on |--------------+
| Cortex-A53| |
+-----------+ |
|
+-----------+ +-----v-----+
|Cortex-M4F |<───────| |
+-----------+ | |
| DebugSS |
+-----------+ | |
|Cortex-M4F |<───────| |
+-----------+ +-----------+
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Peck <jpeck@ti.com>
Change-Id: I8470cb15348863dd844b2c0e3f63a9063cb032c6
Reviewed-on: https://review.openocd.org/c/openocd/+/7088
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since zephyrproject-rtos/zephyr@c3eeae8,
Zephyr OS exposes offset of mode_exc_return in the arch struct for ARM.
Accounting for this allows for consistency and enables
logic with further offsets that may be added after this.
Signed-off-by: Bruno Mendes <bd_mendes@outlook.com>
Change-Id: Id53ebd80c5d98a7d94eb6b00ad638ce51e719822
Reviewed-on: https://review.openocd.org/c/openocd/+/7851
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
These cores are advertised as M23 and M33 compatible, but are identified
by the Realtek implementor id. These cores are found on the RTL872xD
family, at least.
Raw CPUIDs:
Real-M200 (KM0): 721cd200
Real-M300 (KM4): 721fd220
Change-Id: I4106ccb7e8c562f98072a71e9e818f57999d664e
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Presently, we only look at the Part Number field of the CPUID, and
completely ignore the Implmentor field, simply assuming it to be ARM.
Parts have since been found, with different implementors, that use
overlapping part numbers, causing detection to fail.
Expand the "part number" field to be a full implementor+part number,
excluding the revision/patch fields, to make checking more reliable.
Change-Id: Id81774f829104f57a0c105320d0d2e479fa01522
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7845
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There's really no reason to try and add an extra layer of cpu
verification here.
Change-Id: If8c4aa03754607be6c089f514ae300b09b067ffa
Signed-off-by: Karl Palsson <karlp@tweak.au>
Reviewed-on: https://review.openocd.org/c/openocd/+/7844
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use blocks (64 KiB) instead of sectors (4 KiB) when erasing the zd25Q16
SPI flash memory (thanks to Tomas Vanek!)
Change-Id: I969a69ad35f51b84eb3e11b93f0d79db3e98613a
Signed-off-by: Nikolay Dimitrov <nikolay.dimitrov@retrohub.org>
Reviewed-on: https://review.openocd.org/c/openocd/+/7850
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Add missing aarch64_poll() calls to ensure the event
TARGET_EVENT_HALTED is called when necessary.
This is needed with the poller update introduced in commit
95603fae18 ("openocd: revert workarounds for 'expr' syntax change")
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Change-Id: I6e91f1b6bc1f0d16e6f0eb76fc67d20111e3afd2
Reviewed-on: https://review.openocd.org/c/openocd/+/7737
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter.
The driver is based on the openULINK project.
This driver communicate with ANGIE's firmware in order to establish
JTAG protocol to debug the target chip.
Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the
FX2 microcontroller, the driver adds two functions, one to download
the firmware (embedded C) to the FX2, and the second to program
the FPGA with its bitstream.
Add ANGIE's configuration file to tcl/interface/
Add the device VID/PID to 60-openocd.rules file.
Add ANGIE to OpenOCD's documentation
Change-Id: Id17111c74073da01450d43d466e11b0cc086691f
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7702
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The USB control transfer can be executed without any data.
The libusb API libusb_control_transfer() can thus be called with
zero 'size', thus returning zero byte transferred when succeed.
The OpenOCD API jtag_libusb_control_transfer() returns zero either
in case of transfer error and in case of libusb_control_transfer()
returning zero, making impossible discriminating the two cases.
Extend jtag_libusb_control_transfer() with separate return value
for error code and explicit parameter's pointer for transferred
bytes.
Make the transferred pointer optional, as many callers do not
properly handle the returned value.
Use 'int' type pointer for transferred, instead of the 'uint16_t'
that would have matched the type of 'size'. This can simplify the
caller's code by using a single 'int transferred' variable shared
with other jtag_libusb_bulk_read|write, while keeping possible the
comparison int vs uint16_t without cast.
This change is inspired from commit d612baacaa
("jtag_libusb_bulk_read|write: return error code instead of size")
Change-Id: I14d9bff3e845675be03465c307a136e69eebc317
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7756
Tested-by: jenkins
Reviewed-by: ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
This patch changes data types of watchpoint value and mask to allow for
64-bit values match that some architectures (like RISCV) allow.
In addition this patch fixes the behavior of watchpoint command to
zero-out mask if only data value is provided.
Change-Id: I3c7ec1630f03ea9534ec34c0ebe99e08ea56e7f0
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7840
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
register_cache_invalidate() is written a way which uses
pointer arithmetic, which makes it harder to read. This patch
replaces it with more readable way to iterate over array of
structs.
Change-Id: Ia420f70a3bb6998c690c8c600c71301dca9f9dbf
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7735
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Lot of messages was logged as LOG_WARNING, but the operation failed
immediately. Sometimes no error message was logged at all.
Add missing messages, change warnings to errors.
Sometimes ERROR_TARGET_INVALID was returned. Some command handlers
returned ERROR_OK! Always return ERROR_TARGET_NOT_HALTED.
While on it use LOG_TARGET_ERROR() whenever possible.
Prefix command_print() message with 'Error:' to get closer
to LOG_TARGET_ERROR() variant.
Error message was not added to get() and set() methods of
struct xxx_reg_type - the return value is properly checked and a message
is logged by the caller in case of ERROR_TARGET_NOT_HALTED.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I2fe4187c6025f0038956ab387edbf3f461c69398
Reviewed-on: https://review.openocd.org/c/openocd/+/7819
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Compiler would complain that `written` was used without being
initialized.
Simplify the code a little. The number of bytes written is already
checked in usb_write().
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Ibada85dcccfca6f1269c584cdbc4f2e3b93bb8f3
Reviewed-on: https://review.openocd.org/c/openocd/+/7813
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
While not affecting the function's main purpose, an error has
crept into arc_save_context() that results in logging wrong register
values when the debug level is 3 or more. For instance, when debugging a
trivial program and halting at entry to main, the following values are
printed to the log:
Debug: 2915 2020 arc.c:894 arc_save_context(): Get core register regnum=0,
name=r0, value=0x0000000
...
Debug: 2947 2020 arc.c:894 arc_save_context(): Get core register regnum=60,
name=lp_count, value=0x900002d8
Debug: 2948 2020 arc.c:894 arc_save_context(): Get core register regnum=63,
name=pcl, value=0xffffffff
Debug: 2949 2020 arc.c:909 arc_save_context(): Get aux register regnum=64,
name=pc, value=0x900000b4
Debug: 2950 2020 arc.c:909 arc_save_context(): Get aux register regnum=65,
name=lp_start, value=0x900000bc
Debug: 2951 2020 arc.c:909 arc_save_context(): Get aux register regnum=66,
name=lp_end, value=0x00080801
Debug: 2952 2020 arc.c:909 arc_save_context(): Get aux register regnum=67,
name=status32, value=0xffffffff
After the change, the register contents make much more sense:
Debug: 2923 3934 arc.c:889 arc_save_context(): Get core register regnum=0,
name=r0, value=0x00000000
...
Debug: 2955 3934 arc.c:889 arc_save_context(): Get core register regnum=60,
name=lp_count, value=0x00000000
Debug: 2956 3934 arc.c:889 arc_save_context(): Get core register regnum=63,
name=pcl, value=0x900002d8
Debug: 2957 3934 arc.c:903 arc_save_context(): Get aux register regnum=64,
name=pc, value=0x900002da
Debug: 2958 3934 arc.c:903 arc_save_context(): Get aux register regnum=65,
name=lp_start, value=0x900000b4
Debug: 2959 3934 arc.c:903 arc_save_context(): Get aux register regnum=66,
name=lp_end, value=0x900000bc
Debug: 2960 3934 arc.c:903 arc_save_context(): Get aux register regnum=67,
name=status32, value=0x00080801
While at it, simplify a couple of expressions.
Change-Id: I8f2d79404707fbac4503af45b393ea73f91e6beb
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7765
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory region addresses are not in use for now.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9a2189e956ae59b56245ec914ab16719df857b2d
Reviewed-on: https://review.openocd.org/c/openocd/+/7762
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Right after target halt, some activities needs to be done
such as printing exception reason, disable wdts and reading
debug stubs information.
Missing activities will be submitted in the next patches.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I27aad5614d903f4bd7c8d6dba6bfb0bdb93ed8dc
Reviewed-on: https://review.openocd.org/c/openocd/+/7757
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
See section 57.6.1 in RM0432.
Change-Id: Ic4977aee74d1838f420c1d9ff19925d09f8f6e2b
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7763
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STLINK-V3PWR is both a standalone debugger probe compatible with
STLINK-V3 and a source measurement unit (SMU).
Link: http://www.st.com/stlink-v3pwr
This code adds support for the debugger probe functionality.
Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7755
Tested-by: jenkins
To start a ipdbg server one needs to know the tap and the
instruction code to reach the IPDBG-Hub. This instruction is
vendor/family specific. Knowledge which can be provided by the
pld driver.
Change-Id: I13eeb9fee895d65cd48544da4704fcc9b528b869
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7369
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch fixes the handling of errno by setting the sys_errn
only if error has actually occurred during the semihosting call.
It also fixes few issues where error was not set in the first place.
Change-Id: I2fbe562f3ec5e6220b800de04cd33aa1f409c7a0
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This patch introduces function semihosting_opcode_to_str() which
converts semihosting opcodes to strings. This function is then
used in debug messages to improve log analysis and troubleshooting.
Change-Id: Iffea49dae13d6a626ae0db40d379cba3c9ea5bd3
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7726
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
The original document from Jedec does not report the entry for
"21 NXP (Philips)", replaced by "c". It's clearly a typo.
Keep the line from JEP106BF.01 for "NXP (Philips)".
Change-Id: I30215c4ff08d5f112305cde6ab7a3176cdcef948
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7727
Tested-by: jenkins
On Windows, isatty() can return any non-zero value if it's an interactive
device. Which diverges from the ARM semihosting specification. This patch
introduces a fix to make the SYS_ISTTY operation conform to spec.
Change-Id: I9bc4f3cb82370812825d52419851910b3e3f35cc
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7725
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
The old implementation of gdb socket error handling
in the gdb_get_char_inner() differs between Windows and *nix
platforms. This patch simplifies it by using an existing
function log_socket_error() which handles most of the platform
specific things. It also provides better error messages.
Change-Id: Iec871c4965b116dc7cfb03c3565bab66c8b41958
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7724
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added debug prints to show what is the target debug reason. Also added
debug print for Ctrl-C response. This is useful for troubleshooting and
log analysis.
Change-Id: I055936257d989efe7255656198a8d73a367fcd15
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7720
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This patch adds support for the NXP QN908x family of Bluetooth
microcontrollers, such as the QN9080. This chip features a Cortex-M4F
with 512 KiB of flash on all the available versions, although the
documentation suggests that there might be 256 kB versions as well.
The initial support allows to read, erase and write the whole user flash
area. Three new sub-commands under the new "qn908x" command are added
in this patch as well: disable_wdog to disabled the watchdog,
mass_erase to perform a mass erase and allow_brick to allow programming
images that disable the SWD interface.
Disabling the watchdog is required after a "reset halt" in order to run
the CRC algorithm from RAM when verifying the chip. However, this is not
done automatically on probing or other initialization since disabling
the watchdog might interfere with debugging real applications.
The "mass_erase" command allows to erase the whole flash without
probing it, since in some scenarios the chip can be locked such that no
flash or ram can be accessed from the SWD interface, allowing only to
run a mass_erase to be able to flash the program.
The flashing process allows to compute a checksum, similar to the
lpc2000 driver "calc_checksum" but done over a different region of the
memory. This checksum is required to be present for the QN908x
bootloader ROM to boot, and otherwise is useless. As with the lpc2000
design, verification when using "calc_checksum" is expected to fail if
the checksum was not valid in the image being verified.
This was manually tested on a QN9080, including the scan-view,
AddressSanitizer/UBSan and test coverage configurations.
Change-Id: Ibd6d8f3608654294795085fcaaffb448b77cc58b
Co-developed-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Signed-off-by: iosabi <iosabi@protonmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5584
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change implements the predefined type tap_state instead of generic
uint8_t in the driver
Change-Id: I3478e8d7b40b961f3ba77711179016cdcc35cd32
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7722
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This change fixes endianness support in the driver.
Change-Id: Ida360bb58e988cea0a66fdc79e1610b528846fc4
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7721
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang reports that 3rd function call argument is an uninitialized value
file esp32_apptrace.c line:1270
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I73e254d4eb0c6b3152229717d8827d334784ab92
Reviewed-on: https://review.openocd.org/c/openocd/+/7719
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Clang is unable to fully track the content of the array
write_buffer[] and incorrectly complains that it could contain
some uninitialized value.
To help clang to track the execution flow, rewrite the handling of
the buffer by using simpler indexing and by moving away cmd_byte
from the first buffer's element to the variable cmd_byte.
While there:
- fix the error codes returned while parsing the command line and
- use directly command_print_sameline() instead of passing through
intermediate buffers.
Change-Id: I1969e896887ea3a4abebee057cc04c03005fa57c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7718
Tested-by: jenkins
Clang 15.0.7 complains about snprintf output truncation due to
output between 13 and 22 bytes into a destination of size 20.
Increase the size of the buffer.
Change-Id: I0369255ca1bc02a0cf494f765e91a608c960a0d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7717
Tested-by: jenkins
Value in the 'dscsr' variable is garbage until the DAP queue is run.
Postpone evaluation of the 'secure_state' variable. Reading the
core registers in between will execute the DAP queue.
Change-Id: I44959e882dbafb1b9779e813c3d13f3b3dbcd47f
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7693
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The registers pauth_dmask and pauth_cmask are not accessible in
AARCH32 mode. Tagging them as 'hidden' is not enough and triggers
error:
Failed to read pauth_dmask register
while halting the core.
Tag the pauth registers as not existing, unless required by user.
Note: for non existing registers there should be no need to
allocate their register cache. Let's keep this for a further
improvement.
Change-Id: Iaa0d006a3d8ee611ee93333ed49a8615a6c94276
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: d0436b0cda ("armv8: Add support of pointer authentication")
Reviewed-on: https://review.openocd.org/c/openocd/+/7712
Tested-by: jenkins
Reviewed-by: Koudai Iwahori <koudai@google.com>
- Manual integration of File-IO support from xt0.2 release
- Verified with applications linked using gdbio LSP
- No new clang static analysis warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iedc5f885b2548097ef4f11ae1a675b5944f5fdf0
Reviewed-on: https://review.openocd.org/c/openocd/+/7550
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Removed an unused include from src/jtag/adapter.c.
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
Change-Id: Ia5ea0acdfa1c011d7c88decd0f63e8032aafd699
Reviewed-on: https://review.openocd.org/c/openocd/+/7687
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function is used for commands:
- jtag tapisenabled
- jtag tapenable
- jtag tapdisable
While there, add the missing .help and .usage fields and fix the
incorrect check in jtag_tap_enable() and jtag_tap_disable().
Change-Id: I0e1c9f0b8d9fbad19d09610a97498bec8003c27e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7554
Tested-by: jenkins
While there:
- fix memory leak in case of error on values tap->chip,
tap->tapname, tap->expected_ids;
- check for out of memory error;
- fix minor coding style issue;
- add the missing .usage field;
- remove functions not in use anymore.
Change-Id: I1c8c3ffeb324e9eacb919c7e0d94fd72122c9a81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7431
Tested-by: jenkins
Change the prototype of functions:
- target_run_algorithm()
- target_wait_algorithm()
- target_wait_state()
- struct target_type::run_algorithm()
- struct target_type::wait_algorithm()
to use unsigned int for timeout_ms instead of int.
Change accordingly the variables passed as parameter.
Change-Id: I0b8d6e691bb3c749eeb2911dc5a86c38cc0cb65d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7562
Tested-by: jenkins
While there, add the missing .usage field and remove the now
unused function jim_target_tap_disabled().
Change-Id: I79afcc5097643fc264354c6c3957786a55f40498
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7561
Tested-by: jenkins
The function esp32_cmd_apptrace_generic() is not used outside the
file.
Declare it as static.
Detected through 'sparse' tool.
Change-Id: I08c6b92fb01594320bc3ae6b16067ac4eb51ca12
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7676
Tested-by: jenkins
This reverts commit 047b1a8fc2.
Commit 047b1a8fc2 ("target/image: zero-initialize ELF segments
up to p_memsz") breaks the backward compatibility introducing some
problem:
- an empty bss segment with paddr in SRAM gets zero filled at load
but does not survive after a reset, causing verify to fail;
- an empty bss segment with paddr in FLASH causes excessive flash
usage, which can exceed flash size (causing error) and makes
flash aging faster.
Revert it while looking for a better implementation.
Change-Id: Iaaf926dafce46a220a5bbe20c8576eb449996d76
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7658
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Peter Collingbourne <pcc@google.com>
Tested-by: jenkins
Trying to disable OTP write protection by running e.g. `flash protect
1 0 1 off` would already be rejected with an error code, but that would
result in a generic "failed setting protection for blocks 0 to 1"
message. Now a more specific error message is also printed, telling the
user why it failed.
Change-Id: I6d4974eb0bcd23a0a6cf68ff955d9e59b8b1b06a
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-on: https://review.openocd.org/c/openocd/+/7615
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When a DMI operation does not succeed (either because of a timeout
or an error), the specification says that the error in the `op`
field is sticky and needs to cleared by writing `dmireset` in `dtmcs`.
This is already done for timeouts in increase_dmi_busy_delay
but not for errors.
Change-Id: I7c5f27a5cf145511a1a8b64a45a586521e1cbe41
Signed-off-by: Amaury Pouly <amaury.pouly@lowrisc.org>
Reviewed-on: https://review.openocd.org/c/openocd/+/7688
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
this new STM32 series family introduces 2 devices:
STM32C011xx (0x443) and STM32C031xx (0x453)
both devices have 32 Kbytes single flash bank.
Change-Id: I4e890789e44e3b174c0e9c0e1068383ecdbb865f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6874
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The bcm2835gpio driver preferred /dev/gpiomem for access to
memory mapped GPIO control and used /dev/mem as a fallback
only if it couldn't open /dev/gpiomem.
/dev/mem usually requires elevated rights or specific capabilities
of the opening process, so the fallback failed anyway.
Although /dev/gpiomem is the strongly preferred option with respect
to security, there could be also use cases which require /dev/mem
even if /dev/gpiomem is available (e.g. changing the GPIO pad
settings is necessary or testing/debugging OpenOCD).
It was difficult to handle such cases because they required
to block globally the system device /dev/gpiomem
(remove, rename or chmod).
Drop the fallback feature and select the memory device
by 'bcm2835gpio peripheral_mem_dev' configuration command.
Use /dev/gpiomem as a default.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I60e427bda795d7a13d55d61443590dd31d694832
Reviewed-on: https://review.openocd.org/c/openocd/+/7350
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Raspberry Pi 4 with 64-bit kernel and arm_peri_high=1 config.txt
parameter needs peripheral_base 0x47e000000, uint32_t is not enough.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Icedd084e2916657fa4478d452a5eb1e84a45c281
Reviewed-on: https://review.openocd.org/c/openocd/+/7685
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The pads were configured at a wrong memory address
if /dev/gpiomem was mapped.
The pad setting registers are not accessible in mapped /dev/gpiomem,
disable the pads setting if the driver doesn't open /dev/mem.
While on it, do not fail the driver initialization if pad mapping fails
- just emit a warning and work with unchanged pad setting.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I0bce76cade8f7efd75efd9087a7d9ba6511a6239
Reviewed-on: https://review.openocd.org/c/openocd/+/7684
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit dd9137dc0e ("pld/virtex2: add missing error checks") adds
checks on the return value of several functions, allowing also
virtex2_read_stat() to propagate such returned values.
This triggers an error with clang, as it is now able to identify a
possible execution path that makes uninitialized the variable
status.
Check for the returned value of virtex2_read_stat() before using
the variable status and propagate the returned value.
While there, drop a useless empty string.
Change-Id: I7a23d3f904d4e07cdb6f6dfdf1179889b6b8afb8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7657
Reviewed-by: Daniel Anselmi <danselmi@gmx.ch>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The static analyser 'sparse' complains about using sizeof() on a
struct that has variable size:
src/rtos/uCOS-III.c:267:32: warning: using sizeof on a flexible structure
src/rtos/uCOS-III.c:269:41: warning: using sizeof on a flexible structure
src/rtos/uCOS-III.c:275:66: warning: using sizeof on a flexible structure
The struct ucos_iii_params contains either constants values for
different target type and variable fields. The last field is an
variable size array, always allocated to UCOS_III_MAX_THREADS
items. It's not practical to fix this size because we would get
too huge initialization in data segment.
Split away from struct ucos_iii_params all the variable fields and
put them in struct ucos_iii_private. Add in the new struct a
pointer to the selected element of ucos_iii_params_list[] and fix
the size of array threads[] to its maximum value; this would be
allocated at run-time, avoiding impacts to data segment.
Change-Id: I569011a257783d35a8795adbda06e942b4157f2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7678
Tested-by: jenkins
The function rtos_thread_packet() is used across rtos and declared
locally as extern.
Move the prototype of the function in common include rtos.h
Change-Id: I50d311b583148a2de628de0997ef1afc9103a70e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7677
Tested-by: jenkins
The struct containing SWD and JTAG operations are declared as
extern in the C file.
Mode them in include file arm_adi_v5.h to silent 'sparse' error
for global variable definition without declaration in an include
file.
Change-Id: I59088512c052d5a120c38404a882ed512a68ca02
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7675
Tested-by: jenkins
The pointer nand_devices is used in two file.
Move the extern prototype in code.h
Detected through 'sparse' tool.
Change-Id: I7237359fd1a008770a624725cd0b3d8632b4166e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7674
Tested-by: jenkins
The internal variable 'gdb_actual_connections' is used by log and
by semihosting to determine if there are active GDB connections.
Keep the variable local in server's code and only export its value
through a dedicated function.
This solves the issue detected by 'parse' of the variable defined
as global but not declared in any include file.
Change-Id: I6e14f4cb1097787404094636f8a2a291340222dd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7673
Tested-by: jenkins
The function jtag_debug_state_machine_() is only used by a static
inline function and declared inside it as private.
The static analyser 'sparse' complains that the function is
defined as global but not cross checked against a prototype in an
include file.
Move the declaration outside the inline function so it get visible
by interface.c, which already includes interface.h
While there, change the argument type from 'unsigned' to 'unsigned
int' to pass checkpatch check.
Change-Id: Ia5dfb92dc4bc6d52ead4f0cb8c68319c83ff85b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7672
Tested-by: jenkins
Let source file to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I6197f21c857833dafc3d6e3b750c764bf4610abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7671
Tested-by: jenkins
The static analyser 'sparse' complains about values bigger that
255 that gets cast-ed and/or stored in an 8 bit variable.
Rework the functions:
- h_u32_to_le()
- h_u32_to_be()
- h_u24_to_le()
- h_u24_to_be()
- h_u16_to_le()
- h_u16_to_be()
to avoid all the related warnings, without adding any functional
change. Any modern compiler should not be impacted by this.
Change-Id: I0b84043600a41c72d0e4ddb3dd195d69e3b2896b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7670
Tested-by: jenkins
The new committed files add some warning from the static analyser
'sparse':
- Don't assign pointer to 0, use NULL.
- switch with no cases.
Fix them.
Change-Id: I2c02d629bd80b71c8e42553be5d9388bb9b6bcd0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7668
Tested-by: jenkins
The static analyser 'sparse' complains that the functions
clear_malloc() and fill_malloc() are defined global but not cross
checked against a prototype in an include file.
Rework replacements.h and replacements.c to let the former be
included by the latter.
Change-Id: I536393a9c3718dcd7e144cde8f02e169f64c88e0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7667
Tested-by: jenkins
Don't use 'extern' in a C file, but declare the exported function
in a H file.
This helps validating the function prototype across declaration
and use.
Detected through 'sparse' tool.
Change-Id: I2c22b084fb513f4b3b1b1db96dfbc8fa4bfe7238
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7666
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a jtag
driver, that the struct adapter_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of adapter_driver's declaration in interface.h
Drop the preprocessor #ifdef/#endif around the declaration, as it
has no effect when the declaration is not used and/or the symbol
does not exist.
Change-Id: I5b8f5fe48a89ff0ffce38d547c551cd196379fbf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7665
Tested-by: jenkins
Let source files to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I217c2903fdb19e1a2cce39d2536a903c3d72f3f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7664
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a pld
driver, that the struct pld_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of pld_driver's declaration in pld.h
Change-Id: I0f917aecc7534c1b51af0afa9b32ccfd33db3511
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7663
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a nor
driver, that the struct flash_driver is declared in the file as
non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of flash_driver's declaration in driver.h
Fix some incorrect non-const declaration and remove redundant
forward declarations.
Change-Id: I5e41d094307aac4a57dfa9a70496ff3cf180bd92
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7662
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a nand
driver, that the struct nand_flash_controller is declared in the
file as non static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of nand_flash_controller's declaration in driver.h
While there, drop the unused/commented boundary scan controller.
Change-Id: I7dc32cef55be13ba537abe0f4c47b135d837126c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7661
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a rtos'
file, that the struct rtos_type is declared in the file as non
static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of rtos_type's declaration in rtos.h
Change-Id: Ia96dff077407a6653b11920519c1724e4c1167a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7660
Tested-by: jenkins
The static analyser 'sparse' complains, while compiling a target's
file, that the struct target_type is declared in the file as non
static, but it is not exposed through an include file.
The message is:
warning: symbol 'XXX' was not declared. Should it be static?
Move the list of target_type's declaration in target_type.h
While there, fix a name clash in stm8.c
Change-Id: Ia9c681e0825cfd04d509616dbc04a0cf4944f379
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7659
Tested-by: jenkins
To perform any meaningful manipulations with DR the corresponding IR should
be set to a relevant instruction, not BYPASS, so warn the user accordingly.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I42580ecd75ae824a4145f6f17f0df9bcf825b50f
Reviewed-on: https://review.openocd.org/c/openocd/+/7654
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
It's customary to use [] brackets to mean the argument is optional, but
drscan requires at least one pair of "num_bits value" so change it to ().
In common regular expressions * means 0 or more, and + means 1 or more,
so change that too.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: Ib15d833bda2aa398ad1345a042f97d91c98dbf66
Reviewed-on: https://review.openocd.org/c/openocd/+/7653
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While there, add the missing .usage field and move in target.c the
enum nvp_assert.
Change-Id: Ia4f2f962887b5a35faeaa4eae128fa2865569b24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7559
Tested-by: jenkins
Reorganize the code to parse the command line only once.
Add check for successful memory allocation.
Change-Id: Ibf6068e177c09e93150d11aecfcf079348c47c21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7555
Tested-by: jenkins
For some trivial case only, replace calls to jim-nvp with calls
to the new OpenOCD nvp.
Change-Id: Ifd9aff32b67748af8ab808e6a6b6e64f5271b888
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7553
Tested-by: jenkins
New gcc does not understand that the variable 'restore_ms' is set
to 'true' only when the variable 'ms' is assigned in
static int xtensa_write_dirty_registers(...)
{
xtensa_reg_val_t ms;
bool restore_ms = false;
...
if (...) {
ms = regval;
restore_ms = true;
...
}
...
if (restore_ms) {
USE(ms);
}
...
}
and complains about possible use of uninitialized variable 'ms'.
Sadly initialize 'ms' to zero to hide this false positive.
Change-Id: I1fb3949070c8abbf4aa45a740f0ca2fdb753d4fa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7681
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Tested-by: jenkins
Current code tests a function pointer against a numeric value that
is the same enum type as returned by the pointed function.
Clearly the author was willing to call the function and check its
returned value.
Fix the check by calling the function.
Detected through 'sparse' tool.
Change-Id: I27d18d26c2c797160a397daa32835c199014b70b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Checkpatch-ignore: GIT_COMMIT_ID
Fixes: 237e894805 ("reworked etm/etb into a generic etm part with trace capture")
Reviewed-on: https://review.openocd.org/c/openocd/+/7599
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 07e1ebcc12 ("jtag: drivers: with pointers, use NULL
instead of 0") incorrectly inverts the check, making the driver's
pathmove operation not functional and triggering two clang errors.
Fix the check on malloc() returned pointer.
Change-Id: If1f220aca67452adbcd3a1c9cf691fc984b16b27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 07e1ebcc12 ("jtag: drivers: with pointers, use NULL instead of 0")
Reviewed-on: https://review.openocd.org/c/openocd/+/7656
Tested-by: jenkins
When gatemate_set_instr() fails, the array pointed by
bit_file.raw_file.data is not freed.
Issue identified by OpenOCD Jenkins clang build.
Free the array while propagating the error.
Change-Id: I2f7fadee903f9c65cdc9ab9b52ccb5803b48a59d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 682f927f8e ("pld: add support for cologne chip gatemate fpgas")
Reviewed-on: https://review.openocd.org/c/openocd/+/7632
Tested-by: jenkins
Reviewed-by: Daniel Anselmi <danselmi@gmx.ch>
Let source file to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I8ae2f8f1fdaea5683e157247463533b17237e464
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7602
Tested-by: jenkins
On 32 bit hosts, gcc should consider constants without suffix as
32 bits values.
Use the suffix 'ULL' to guarantee it is a 64 bit.
Detected through 'sparse' tool.
Change-Id: I205ca986968fef9a536f87492d1f6c80e41829f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7601
Tested-by: jenkins
Don't compare pointers with 0, use NULL when needed.
Don't assign pointer to 0, use NULL.
Detected through 'sparse' tool.
Change-Id: Ifa81ba961c0d490cc74880b4a46b620e6358f779
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7598
Tested-by: jenkins
Don't compare pointers with 0, use NULL when needed.
Don't assign pointer to 0, use NULL.
Don't pass 0 ad pointer argument, pass NULL.
Detected through 'sparse' tool.
Change-Id: I3f867cb9c0903f6e396311e7b3970ee5fb3a4231
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7597
Tested-by: jenkins
Let source file to include its file .h to validate the exported
prototypes.
Detected through 'sparse' tool.
Change-Id: I5de107b4f8a468f0e37f06171f5f0c3c0546db1a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7596
Tested-by: jenkins
Add static type to symbols that are not used elsewhere.
Detected through 'sparse' tool.
Change-Id: I2bdac5d2b06a6dbed5c27bfdb1cf36eee90ad823
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7594
Tested-by: jenkins
On 32 bit hosts, gcc should consider constants without suffix as
32 bits values. Adding a cast to convert it to 64 bits should not
be enough.
Use the suffix 'ULL' to guarantee it is a 64 bit.
Detected through 'sparse' tool.
Change-Id: If6be35bd3cbbc7c3a83e0da1407e611f07ff6e06
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7593
Tested-by: jenkins
Don't compare pointers with 0, use NULL when needed.
Don't assign pointer to 0, use NULL.
Don't pass 0 ad pointer argument, pass NULL.
While there, check for return value from malloc(), replace an
assert() with a LOG_ERROR(), drop a useless cast.
Detected through 'sparse' tool.
Change-Id: Ia7cf52221b12198aba1a07ebdfaf57ce341d5699
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7592
Tested-by: jenkins
Add static type to symbols that are not used elsewhere.
Detected through 'sparse' tool.
Change-Id: I00e151d2466868a5dce028444d326defb80d4826
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7591
Tested-by: jenkins
It looks like a false positive.
Scan-build considers as possible to:
- have list_empty() return false;
- list_for_each_safe() to not execute any loop, thus not assigning
a non-NULL value to 'block';
- the NULL pointer 'block' is passed to list_del().
This is not possible because with list_empty(), the loop runs at
least once.
Rewrite the function to simplify the code and making it easier for
scan-build to check it.
This also drops an incorrect use of list_for_each_safe(), where
the 'safe' version was not required.
Change-Id: Ia8b1d221cf9df73db1196e3f51986023dcaf78eb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 8d1dcf293a ("target/espressif: add application tracing functionality over JTAG")
Reviewed-on: https://review.openocd.org/c/openocd/+/7608
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
When the function xtensa_queue_dbg_reg_read() returns error, the
array 'tmp' remains not initialized and scan-build complains while
computing buf_get_u32() that:
Result of operation is garbage or undefined
Check the returned value of xtensa_queue_dbg_reg_read() and
propagate it.
Change-Id: If0aaad068b97ef0a76560e262d16429afd469585
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 8d1dcf293a ("target/espressif: add application tracing functionality over JTAG")
Reviewed-on: https://review.openocd.org/c/openocd/+/7607
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Below warnings are fixed.
1- A function declaration without a prototype is deprecated in all
versions of C [-Werror,-Wstrict-prototypes]
2- error: variable set but not used [-Werror,-Wunused-but-set-variable]
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1cf14b8e5e3e732ebc9cacc4b1cb9009276a8ea9
Reviewed-on: https://review.openocd.org/c/openocd/+/7569
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
ARMv8-R platforms are similar to ARMv8-A regarding
JTAG and most cpu registers. ARMv8-R doesn't has MMU
but has MPU instead.
ARMv8-R platforms can be AArch32 only such as Cortex-R52,
or AArch64 capable like Cortex-R82.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: Ib086f71685d1e3704b396d478ae9399dd8a391e1
Reviewed-on: https://review.openocd.org/c/openocd/+/6843
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Linux kernel and user space border is 0xc0000000 not 0xc000000
Signed-off-by: panciyan <panciyan@eswincomputing.com>
Change-Id: I6b487cce62ac31737deca97d5f5f7bbc081280f4
Reviewed-on: https://review.openocd.org/c/openocd/+/7570
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This feature allows to transfer arbitrary data between host and
ESP32 via JTAG.
The main use cases:
1- Collecting application specific data
2- Lightweight logging to the host
3- System behaviour analysis with SEGGER SystemView
4- Source code coverage
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I95dee00ac22891fa326915a3fcac3c088cbb2afc
Reviewed-on: https://review.openocd.org/c/openocd/+/7163
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On MacOS libc includes files from MacOSX.sdk that define the macro
#define __nonnull
without arguments, causing compile error.
Extend the existing check for clang on MacOS and undefine the
macro for gcc too.
Change-Id: Ic99de78348c6aa86561212a3aded9342e5d32e02
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7571
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
Minor changes due to kernel switch to 100 char/line.
Added four new functions.
Silent checkpatch; we don't want to diverge from Linux reference
code.
Checkpatch-ignore: MACRO_ARG_REUSE, UNNECESSARY_PARENTHESES
Checkpatch-ignore: MACRO_ARG_PRECEDENCE
Change-Id: I1d2ff25bf3bab8cd0f5c9be55c7501795490ea75
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7568
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The file list.h is taken from Linux and includes two similar
implementation of double linked lists:
- with single linked list's head (hlist_*), and
- with double linked list's head (list_*).
While the former offers a minor memory footprint improvement,
keeping two implementations makes harder for newbie developers
to approach them.
So far only the latter implementation has been used and no new
patches in gerrit is going to change that.
Drop the support for lists with single linked head.
It can be easily taken back from git history, if needed.
Change-Id: I420e5de38ab755fdfbeb2115538c61818308ec2b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7567
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add the fast read method to speed up flash verification
after programming. Works the same as fast write already
implemented.
Signed-off-by: François LEGAL <devel@thom.fr.eu.org>
Change-Id: I74611a3542a88212f0483ec8ee368aba3d1f03c7
Reviewed-on: https://review.openocd.org/c/openocd/+/7564
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The condition to check if the workspace area (used by actual MIPS code
executed on target) and data area (sandbox to put data to be read/written
to/from flash) is wrong, thus preventing the use of FAST_* commands to
program/verify FLASH.
Signed-off-by: François LEGAL <devel@thom.fr.eu.org>
Change-Id: Ic68424b7f42d44e550433a120093db5e7980fd56
Reviewed-on: https://review.openocd.org/c/openocd/+/7563
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
1.
update the rtos->thread_count in time, to make sure the allocated
thread_name_str and extra_info_str could be freed by
rtos_free_threadlist(). Otherwise the abnormal return may cause a
memory leak.
2.
remove a redundant assignment to threadid.
Signed-off-by: Chao Du <duchao@eswincomputing.com>
Change-Id: Ifabc59d501c925b3d6aec8b04b2856d2c31cc4e2
Reviewed-on: https://review.openocd.org/c/openocd/+/7549
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If the file read abnormally, need to close it which was opened before.
Signed-off-by: panciyan <panciyan@eswincomputing.com>
Change-Id: I6142f154741dcd38088b7add2793219ee4dd2ae9
Reviewed-on: https://review.openocd.org/c/openocd/+/7546
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This also fixes an incorrect return ERROR_xx from a jim command,
propagated from return value of rtos_smp_init().
Change-Id: Icf4893c00aabd8fadd60077c5e8a2e926f687518
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7511
Tested-by: jenkins
Print one entry per line.
While there add the mandatory 'usage' field.
Change-Id: Ia832684817f3bdbfa4cb943cd97e3f9fb2605902
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7510
Tested-by: jenkins
Print one entry per line.
While there add the mandatory 'usage' field.
Change-Id: I135556e12154e33fdbd0f71d89f6fe37c69813b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7509
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I3e5b826ca58f7ade30a443ada0cb4a9cd9ea35c2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7508
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I5389881dac25877dc32930ec36ee546e48ecc14d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7507
Tested-by: jenkins
While there, fix typo on 'exceeds'.
In a following patch, the output could be formatted and split in N
values per line to make it easier to read by humans.
Change-Id: I295111a80934393011e46311f6cf6c13f2bdc0a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7503
Tested-by: jenkins
While there, format in a human readable way the output list by
using one line per tpiu name.
Change-Id: I937c92b6c1e92509cf8aa96be1517a51bc363600
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7501
Tested-by: jenkins
While there, format in a human readable way the output list by
using one line per dap name.
Change-Id: I24a47350105b90db15808c61790f05d807120739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7498
Tested-by: jenkins
While there:
- check the number of command parameters;
- add the mandatory 'usage' field.
Change-Id: I7cd16f049753caedf19f313f7dc84be98efdba42
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7497
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I316fb31e24e94985dcc724e428b0384be7ef5bdd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7496
Tested-by: jenkins
While there add the mandatory 'usage' field.
Change-Id: I3491ed79d11c5a3e81cc9afd2423da14b8df72ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7495
Tested-by: jenkins
While there:
- format in a human readable way the output list by using one line
per tap name;
- add the mandatory 'usage' field.
Change-Id: I295449220c78fac8973478b265413342ea832f61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7494
Tested-by: jenkins
While there, format in a human readable way the output list by
using one line per cti name.
Change-Id: I6d4870ee512fe7e6935d73355c2377ad805ccc3b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7492
Tested-by: jenkins
While there, add a check for target halted and check the number of
parameters accordingly to the command name.
Change-Id: I9e8bb109c35039561997d14782fac682267aee65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7491
Tested-by: jenkins
This also fixes an incorrect return ERROR_TARGET_NOT_HALTED from a
jim command.
Change-Id: I99a02a21bedb64e60944e295c7cf24356e07be60
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7490
Tested-by: jenkins
This also fixes a mistake of the jim command returning ERROR_xx
when function rtt_read_channel_info() returns error.
While there:
- format in a human readable way the output dictionary list, while
preserving the structure of its TCL data;
- add check for the number of parameters.
Change-Id: Ica2b623699d3a606d3992975c836dae96f74b26d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7489
Tested-by: jenkins
Use full 64 bits in output; no reason to truncate at 32 bits.
Change-Id: I433815a381e147731ff0da2c805170649a9bcf38
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7487
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'flash list' as OpenOCD command.
While there:
- format in a human readable way the output dictionary list, while
preserving the structure of its TCL data;
- add the mandatory 'usage' field.
Change-Id: I1ee69870d3ab3c1cfc46cd2b8ec03de6b2300bd6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7486
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'transport select' as OpenOCD command.
This fixes and incorrect check for the return value of function
transport_select(); it returns ERROR_yy but the check is on JIM_xx.
While there, fix the coding style.
Change-Id: I9f3e8394c1a0cc0312b414c58275e1220217bbed
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7485
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The mixed use of jim commands and OpenOCD commands is error prone
due to handling of errors through JIM_xx and ERROR_yy.
Rewrite the jim command 'ocd_find' as OpenOCD command.
Change-Id: Id775bccc12840bcf95d8c19787beda5e7c3107fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7484
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The command 'svf' is the only command in OpenOCD that accepts
options in both forms 'option' and '-option'.
Deprecate the option format without the leading '-'.
Update the documentation and fix the on-line help.
While there:
- switch to use the new nvp.h helper;
- return ERROR_COMMAND_ARGUMENT_INVALID on invalid command args;
- fix some minor coding style rule.
Change-Id: I5b944403d92a3fa1e12d5faafc1d2a139bc16a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7534
Tested-by: jenkins
If svf_set_padding() returns error, jump to free_all label to
prevent any memory leak.
Propagate the error reported by svf_set_padding() instead of
overwriting it.
Use command_print() instead of LOG_ERROR() for command output.
Change-Id: I61fd89cad10652f2f9ef1f9d48a040e35253c3d4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7533
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The file descriptor svf_fd is not closed on command error, thus
leaking memory.
Close svf_fd on errors.
While there, properly initialize svf_fd using NULL instead of 0.
Change-Id: I5efe9ce576a3a50588b30000222665e26161dfdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7532
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: <kai.schmitz@advantest.com>
The code for JTAG WAIT recovery did not handle DP_SELECT
endianness.
While on it, mark missing ADIv6 DP SELECT1 handling as TODO.
Change-Id: I44f3bc8fc9fd2483c0293b6d4f2c51a60ca01873
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7540
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The multidrop SWD is also supported.
Change-Id: I9fefc54fc9d40a75194285cd6e0f10c5c347d9b6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7537
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The value returned by target_get_gdb_arch() is something specific for GDB.
There could be several variants of the same CPU.
If we start implementing all the variants, checking the string value,
could become incorrect.
It's better to check for xtensa->common_magic == XTENSA_COMMON_MAGIC
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I20f3fdced176c3b9ab00f889743161ecad7280f9
Reviewed-on: https://review.openocd.org/c/openocd/+/7536
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Almost written from the beginning in a modern OpenOCD way.
- Endiannes support
- Proper variable types
- Align with the other rtos implementations
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0868a22da2ed2ab664c82b17c171dc59ede78d10
Reviewed-on: https://review.openocd.org/c/openocd/+/7444
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
-noreset: when using several SVF input files in a sequence it is not always
desireable to have a JTAG reset between the execution of the files.
The -noreset option skips this unwanted reset.
-addcycles <x>: some tests rely on a certain number of extra clock cycles
between the actual JTAG commands. The -addcycles option injects a number
x cycles after each SDR instruction.
Signed-off-by: Kai Schmitz <kai.schmitz@advantest.com>
Change-Id: I31932d6041dbc803be00016cd0a4f23fb2e7dbe1
Reviewed-on: https://review.openocd.org/c/openocd/+/7433
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The macro JIM_EMBEDDED was required to be defined before including
jim.h in applications that embed jimtcl.
This requirement has been dropped in 2010 by removing the file
dos/Embedder-HOWTO.txt from jimtcl in
https://github.com/msteveb/jimtcl/commit/2d8564100c86#diff-3e93fa55e666
Drop the macro definition and the comment that mandates it.
Change-Id: I36883f60f25bb25839e4ebf908159569659764dd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7518
Tested-by: jenkins
Not all compilers nor compiler versions supports the attributes
used in OpenOCD code.
Collect in a single file the workaround to handle them.
Change-Id: I92d871337281169134ce8e40b2064591518be71f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7519
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- Manual integration of NX support from xt0.2 release
- No new clang static analysis warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I95b51ccc83e56c0d4dbf09e01969ed6a4a93d497
Reviewed-on: https://review.openocd.org/c/openocd/+/7356
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We were previously not zero-initializing ELF segments between p_filesz
and p_memsz (aka BSS). However, this may be necessary depending on the
user's application. Therefore, start doing so.
Change-Id: I5a743390069583aca7ee276f53afeccf2cac0855
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7513
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
All DIDs are taken from "SAM R34/R35 Errata Sheet" (DS80000834A).
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: Ie35f58e61bb02919c0676c91938c90192481d995
Reviewed-on: https://review.openocd.org/c/openocd/+/7521
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to the datasheets these MCUs have 40Kb RAM.
Signed-off-by: Andrew Lalaev <andrey.lalaev@gmail.com>
Change-Id: I52b8a0c86035bccd6f3c1a478bb2e558bca4ae86
Reviewed-on: https://review.openocd.org/c/openocd/+/7520
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The driver tries to open mpsse engine for each vid pid
pair in sequence. If more vid/pid pairs are configured and
the USB device does not correspond to the first pair,
the driver shows 'unable to open ftdi device ...' error.
Match vid pid with the whole list as used in jtag_libusb_open()
instead of multiple mpsse_open() in for loop over vid/pid pairs.
Change-Id: I8ef55205be221c727607fe25b81ae21de0d96f02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7529
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Can be employed by a driver with custom libusb open.
Change-Id: I00c8a01df8780891a8b7c30e2e34ab191acdf9a8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7528
Tested-by: jenkins
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We currently fail the transfer when issuing more than 255 transactions
at once, e.g.
> read_memory 0x10000000 32 256
CMSIS-DAP transfer count mismatch: expected 257, got 1
This is because the protocol only supports 255 transactions per packet
(65535 for block transactions), and as a result we truncate the
transaction count when assembling the packet. Fix it by running the
queue when we hit the limit.
Change-Id: Ia9e01e3af5ad035f2cf2a32292c9d66e57eafae9
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 40bac8e8c4 ("jtag/drivers/cmsis_dap: improve USB packets filling")
Reviewed-on: https://review.openocd.org/c/openocd/+/7483
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The OpenOCD commands produce their TCL text result through the
pair command_print() and command_print_sameline().
The latter is used to concatenate output in a single line.
At the end of a sequence of command_print(), the last LF is taken
as part of the command result, while it is not always needed, and
it is even annoying when the output of two commands needs to be
concatenate in a single line.
Using command_print_sameline() in place of the last call to
command_print() would solve the problem but it's quite expensive
in term of coding to fix all the existing commands.
Drop the last LF, if present.
Commands that would specifically need a LF as last char, can add
an extra LF at the end of the output.
Document this behavior in command.h.
Change-Id: I6757c20fbfce923dd393083146e8d5a1f3b790b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7471
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A bunch of new SPI flash (Adesto, Cypress, XTX Tech, mainly octal)
IDs and SPI FRAM (Infineon) IDs added. Backward compatible change
of ID interpretation: The previously unused 4th byte now acts
as continuation code (0x7F) count for manufacturer id, cf.
JEDEC JEP106BC. Currently this affects only some recent octal flash
and FRAM devices, which are only supported by stmqspi and cmspi
flash drivers.
Change-Id: Ibdcac81a84c636dc68439add4461b959df429bca
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6929
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While there, fix some coding style error and remove the now unused
function jim_arc_read_reg_name_field() and the macro
JIM_CHECK_RETVAL().
Change-Id: I140b4b929978b2936f2310e0b7d1735ba726c517
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7426
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Use a COMMAND_HELPER() to avoid memory leaks when the helper
COMMAND_PARSE_NUMBER() returns due to an error.
While there:
- fix potential SIGSEGV due to dereference 'type' before checking
it's not NULL;
- fix an incorrect NUL byte termination while copying to
type->data_type.id and to bitfields[cur_field].name;
- fix some coding style error;
- remove the now unused function jim_arc_read_reg_type_field().
Change-Id: I7158fd93b5d4742f11654b8ae4a7abd409ad06e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7425
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Use a COMMAND_HELPER() to avoid memory leaks when the helper
COMMAND_PARSE_NUMBER() returns due to an error.
While there:
- fix potential SIGSEGV due to dereference 'type' before checking
it's not NULL;
- fix an incorrect NUL byte termination while copying to
type->data_type.id and to bitfields[cur_field].name;
- fix some coding style error.
Change-Id: Ide4cbc829871a6a523026ccc0d3100dadc2afd06
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7424
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Long ago jim_nvp was part of jimtcl. When jimtcl dropped it,
OpenOCD kept copy of it in its code base. Current code of jim_nvp
is still related with jimtcl data types and functions.
With the target of better isolating OpenOCD code from jimtcl,
create a new file nvp.c that re-proposes only the core of the old
jim_nvp, dropping any link with jimtcl and removing the string
'jim' either from the filename and from the code.
Keep the same license from the old code, as the new files are
clearly derived from it.
Change-Id: I273448cf1f1484b10f6b6113ed7bb0fcf946482b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7423
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
The command is specified through COMMAND_HANDLER. It should not
return JIM_OK / JIM_ERR.
Change-Id: I56666414d49b0298ecc23ec7ef30c77e1e27afa8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7413
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Also drop arc_cmd_jim_get_uint32() that is now unused.
Change-Id: Ic26c3f008376db3f01215bf736fca736dd1c1a4f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7412
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes several incorrect return ERROR_xxx from a jim
command.
Change-Id: I34fe3552d3dc344eac67bf504c5d5709b707fdfd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7411
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I72a522645f62b99b313573c8bad6d4f674c5ae53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7410
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I1f9cf5d1dfa38b8a06042b5f54209e6ee2fc4e0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7409
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: Iab9bc7c25181341a632f608a8ef2d8b0bea72520
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7408
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
This also fixes an incorrect return ERROR_OK from a jim command.
Change-Id: I3c51355e7e05965327ce819a3114e370f2de5249
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7407
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
SW-DPv2 and SWJ-DPv2 devices do not reply to DP_TARGETSEL write cmd.
Ignore the received ACK after TARGETSEL write.
While on it, use swd_ack_to_error_code() for unified error code
translation of the received ACK value for all other commands.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If978c88c8496e31581175385e59c32faebfd20aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
And add its own header to the rtos_xxx_stackings.c
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I084130fde7ee8645129a7cf60bb7bf59448e2f39
Reviewed-on: https://review.openocd.org/c/openocd/+/7441
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
No functional change, the delay is unchanged.
Change-Id: I5b5e837d741ac01fc573657357c5fe61ad901319
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7262
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After setting adapter speed to some values, the driver
shows the real speed little bit higher.
Although it does not impose a problem from technical point
of view because the difference is smaller than usual speed error,
it looks at least strange to the user. The documentation reads
that real frequency should be same or lower than requested.
Use proper rounding in speed -> delay and delay -> speed
conversions.
Change-Id: I1831112cc58681875548d2aeb688391fb79fa37f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7261
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
bitbang_swd_exchange(rnw=true,...) calls bitbang_interface->swd_write()
with swdio clamped to 0.
bitbang_swd_write_reg() reads 1 turnaround bit, 3 ack bits
and 1 turnaround by one call to bitbang_swd_exchange()
and then switches SWDIO to output.
AFAIK all bitbang interfaces switch SWDIO GPIO direction immediately
in bitbang_interface->swdio_drive().
The GPIO now drives SWDIO line to the value stored in the output register
which is always zero from previous bitbang_swd_exchange(rnw=true,...).
In case the following data bit (bit 0) is 1 we can observe a glitch
on SWDIO:
_____ out 1 ____
HiZ/pull-up ----\ /
\ /
\______ out 0 ______/
swdio_drive(true) swd_write(0,1)
The glitch fortunately takes place far enough from SWCLK rising edge
where SWDIO is sampled by the target, so I believe it is harmless
except some corner cases where the reflected wave is delayed on long
line.
Anyway keeping electrical signals glitch free is a good practice.
To keep performance penalty minimal, pre-write the first data
bit to SWDIO GPIO output buffer while clocking the turnaround bit.
Following swdio_drive(true) outputs the pre-written value
and the same value is rewritten by the next swd_write()
instead of glitching SWDIO.
Change-Id: I72ea9c0b2fae57e8ff5aa616859182c67abc924f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7260
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The OpenJTAG driver logs "num_cycles > 16 on run test" warning
whenever the JTAG_RUNTEST operation cycle count is larger than 16.
Instead of logging the warning and only running the first 16 TCLK
cycles, remove the warning and queue up multiple operations of up
to 16 cycles each.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Id405fa802ff1cf3db7a21e76bd6df0c2d3a0fe61
Reviewed-on: https://review.openocd.org/c/openocd/+/7420
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Works for the proprietary rt-kernel from rt-labs.
See: https://rt-labs.com/product/rt-kernel/
Change-Id: Id2c2e292c15fb17eab25e3d07db05014daa2a2b0
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6668
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is optional field for the targets which has to implement
their custom stack read function.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Icbc9ed66a052fc2cc0ef67e3ec4d85ab0c2c1b94
Reviewed-on: https://review.openocd.org/c/openocd/+/7442
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Other OSes have separate files to keep stack register offsets.
Adding them for NuttX as well will provide a clearer way to expand.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I1428fefefa199a95431f2073c0279dd7028ad8da
Reviewed-on: https://review.openocd.org/c/openocd/+/7250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This generalizes the little endian CRC32 function used in the OR1K
target and moves it to a common helper, so that other places do not need
to reinvent the wheel. It is directly used in the OR1K target.
Change-Id: I0e55340281a5bfd80669bb1994f3a96fecc1248a
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7415
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Polling the target makes no harm during PSoC 4 flash write in the current
OpenOCD code. Don't mask it.
Change-Id: I6625ded0162ee3a96b92188844d0d2d6c30101c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7162
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The commands 'jtag newtap' and 'swd newdap' have to work either on
HLA transport and on standard JTAG/SWD. Having a dedicated
implementation for HLA is a non-sense.
Reuse the generic code jim_jtag_newtap() and drop the files
hla_tcl.[ch] as they are now empty.
Change-Id: I9dabbdc2a6f338f23b2fd3ed1a4dc3da0200c080
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7428
Tested-by: jenkins
The same code is currently used for commands 'jtag newtap' and
'swd newdap' (plus dapdirect versions), but for SWD case the code
skips the parsing of the command line as not every flag is used.
This has the drawback that syntax errors get unchecked.
Move the check about the transport so the command line get always
parsed even when the corresponding flags are not useful.
Change-Id: I596c3beb04e9e8a9ebe6ee68a61395b679d43b3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The line reset SWD sequence is used quite often in SWD multidrop mode.
Prevent the ugly connect/disconnect adapter firmware bug workaround
to be called before each line reset.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id85bff075dba9077e4e501e2cdcfd64d5d9d0531
Reviewed-on: https://review.openocd.org/c/openocd/+/7381
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DAP_TransferBlock command saves n - 3 bytes in comparison to DAP_Transfer,
where n is number of transfers.
Use DAP_TransferBlock optionaly to save some USB bandwidth.
The change increases the speed of the write transfer
from 40 KiB/s to 42 KiB/s @ USB FS, adapter speed 1000.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ifde0159cfd44481d2b81b90daa088e731c03e26d
Reviewed-on: https://review.openocd.org/c/openocd/+/7372
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DAP write transaction occupies 5 bytes of a command packet.
DAP read transaction needs just one byte in a command packet
and expect 4 bytes in a response.
The fixed maximal number of transactions in a packet caused
packet filling less than optimal.
Compute both command and expected response sizes based on
read or write direction of each transaction.
Run the queue if one of sizes does not fit into a packet.
The change increases the speed of the mostly read transfer
from 36 KiB/s to almost 40 KiB/s @ USB FS, adapter speed 1000
due to reduction of adapter inserted RDBUFF reads.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib70812600eaae0403b8ee8673b6f897348496569
Reviewed-on: https://review.openocd.org/c/openocd/+/7364
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
USB bulk backend needs to avoid zero sized USB packets
sent after each full sized packed for performance reasons.
HID backend uses fixed size HID reports so the full size
of the report can be utilized.
Introduce packet_usable_size to reflect it.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I34094c9edac5730624480711cbd6aa65883c47c7
Reviewed-on: https://review.openocd.org/c/openocd/+/7363
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Not all variables converted, JTAG part is left as is.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ie9cc890769a2f53cb3a07fd457030e1b98910d44
Reviewed-on: https://review.openocd.org/c/openocd/+/7362
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace the direct dereference of cmsis_dap_handle by dereference
of the dap function parameter wherever possible.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I32601dbe0270267642720a8524706aa76d187c3b
Reviewed-on: https://review.openocd.org/c/openocd/+/7361
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move all pending request FIFO related variables to
the struct cmsis_dap
Pure refactoring, no functional changes.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I2cea9c1e265ac102ec0f314767b8b9afdcda9ee9
Reviewed-on: https://review.openocd.org/c/openocd/+/7360
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Simply move numicro M0 flash write assembly to contrib/loaders. Also,
modify corresponding Makefile and generated numicro_m0.inc.
To make the path more general, this patch rename the path
"contrib/loaders/flash/numicro_m4" to "contrib/loaders/flash/numicro" as
well.
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9adea24c2b3c97319a9b015cf50257f3d131dc26
Reviewed-on: https://review.openocd.org/c/openocd/+/7346
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is picked from the flash part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support flashing Nuvoton's Cortex-M4 chips: M541 & NUC442/472 series.
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9dc69eccb851df14c1b0ce2f619d7b3da0aa92aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7329
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is picked from the flash part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
It reorders Nuvoton MCU part list and spreads out the way to define the
banks' base address & size of the parts.
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I1f21f54dfdf53e5b8ea04d803347d1dbc8c321a0
Reviewed-on: https://review.openocd.org/c/openocd/+/7339
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The org.gnu.gdb.arm.m-system GDB feature defines the name in lowercase
letters.[1] Not adhering to the definition can cause issues with tools
interacting with the GDB which expect the correct casing.
[1]: https://sourceware.org/gdb/onlinedocs/gdb/ARM-Features.html
Change-Id: I0b6584a78f86b053947d79686baad5dac3ec4a00
Signed-off-by: Boris-Chengbiao Zhou <bobo1239@web.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7292
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Do not warn the user about adapter speed not being set
if the selected adapter does not support configurable speed.
This would be confusing to users.
- Minor reword in the "adapter speed is not selected" warning.
- Print the adapter name in the "adapter doesn't support
configurable speed" log entry
- Another minor reword: autoselect --> autoselecting
Signed-off-by: Jan Matyas <matyas@codasip.com>
Change-Id: I4c198b547544fd8199921f092153562c5f159134
Reviewed-on: https://review.openocd.org/c/openocd/+/7269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Do not read ID from SPI flash and suppress autodetection
if non-zero flash bank size is configured.
Change-Id: Idcf9ee6ca17f9fa89964a60da7bf11e47b4af5e7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7241
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Cortex-M support for SMP multicore targets.
This SMP implementation unlike older ones does not act
on the first halted target found. It polls targets
until a SMP group is finished and stores eventual
'halted' events instead of emitting them. As soon as polling
of a group is done, poll proceeds with SMP related tasks.
This approach improves detection of a reason why debug
stopped - a correct reason is detected for all targets,
not only for the first found.
Drawback: SMP target group should be defined in the same
order as the targets were defined.
Obsolete gdb 'J' packet/smp_gdb command core switching is not implemented,
use with rtos hwthread.
Only one core is resumed if debug_execution is requested.
Some ideas taken from Graham Sanderson's [4936]
and src/target/aarch64.c
Added error checking of armv7m_restore_context().
Change-Id: I60f5b79e74b624dc2b5835ff10e38ac2ccb23792
Link: [4936]: target/cortex_m: Add smp support for Cortex M | https://review.openocd.org/c/openocd/+/4936
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When pointer authentication is enabled, some upper bits of the link
register (LR[63:VA_SIZE]) are used to store a signature. Therefore, GDB
need to remove the signature to get backtraces.
GDB has support of pointer authentication. When pointer authenticaion is
enabled, GDB requests 8-bytes mask to the target to remove the
signature. mask[63:VA_SIZE] should be all set and mask[VA_SIZE-1:0]
should be all cleared. GDB removes the signature by addr&~mask or
addr|mask.
I added a feature to provide the mask for pointer authentication.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: I56fbbf9cc23619b6536ecd326f350c8bf137f322
Reviewed-on: https://review.openocd.org/c/openocd/+/7248
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Extended feature. This is a large patch, but is self-contained to the
eCos support and does not affect any other openocd functionality. It
does NOT affect existing eCos RTOS plugin users where their
applications do not provide the extended symbolic helper
information. If the helper symbols are not available the rtos support
code will behave as before. This "dynamic" functionality is *required*
because eCos does NOT have a fixed/hardwired, known, layout for the
thread descriptor structure. The per-application build eCos
configuration can affect the shape of the thread descriptor structure
(field presence, and hence offsets of subsequent fields) such that
constant values cannot be used to consistently interpret all possible
eCos application configurations. For historical reasons, there is not
yet a consistent namespace for the helper symbols across eCos HALs
hence the support is currently limited to specific architectures
(Cortex-M and ARM/Cortex-A). No new Clang analyser warnings are raised
by this changeset.
Change-Id: Ib3a36877326eeb56595cbca55e21b9e59a59c98a
Signed-off-by: James G. Smith <jsmith@rallysmith.co.uk>
Reviewed-on: https://review.openocd.org/c/openocd/+/6275
Reviewed-by: Alex Schuilenburg <alex.schuilenburg@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The HiFive Inventor uses this flash chip, so adding it will allow for
openocd to be used to program it. These values were taken from the
chip's documentation.
Signed-off-by: Fawaz Tirmizi <fawaz@rivosinc.com>
Change-Id: I15c9d35f99d4500f73134cdc2d1b9ab6279b491c
Reviewed-on: https://review.openocd.org/c/openocd/+/7135
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In any case flag will be set as examined.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I5177ee656f726a807269e2f4725223f50e49e855
Reviewed-on: https://review.openocd.org/c/openocd/+/7231
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With OpenOCD v0.12.0 released, drop the workarounds for 'expr'
syntax change by reverting:
- commit 320043c054 ("openocd: fix for polling during "expr"
computation");
- commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change").
Replace the call to target_call_timer_callbacks_now() with call
to target_call_timer_callbacks().
Change-Id: Iae5afc50e3f688e11176a52648efc9a6577a9a11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7405
Tested-by: jenkins
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
In FreeBSB 13.0 the build fails due to redefined macro __packed.
src/jtag/drivers/esp_usb_jtag.c:19:9: error: '__packed' macro
redefined [-Werror,-Wmacro-redefined]
#define __packed __attribute__((packed))
^
/usr/include/sys/cdefs.h:223:9: note: previous definition is here
#define __packed __attribute__((__packed__))
^
1 error generated.
Drop the macro and align the code with the other files in OpenOCD
project, where the attribute is directly applied without using a
macro.
Change-Id: I89ae943e77036206d40d4d54172cd4a73e76e5c5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Wojciech Puchar <wojtek@puchar.net>
Reviewed-on: https://review.openocd.org/c/openocd/+/7435
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
This patch fixes two corner-cases of finding RTT control block.
The first one is when there was a partial match (even single byte) at
the end of loaded buffer (uint8_t buf[1024]), but this was not part of
full match. In that case `cb_offset` was not updated correctly and the
returned `*address` was lower by the legth of the partial match. In case
of searched 'SEGGER RTT' (the default control block ID) string, it was
enough to match `buf[1023] == 'S'`, which is quite likely to happen, and
the `*address` was offset by 1 (e.g. it was 0x20000fff instead of
0x20010000).
Updating (or even maintaining) `cb_offset` is not needed, as start
address of control block can be calculated based on memory address that
was loaded into `uint8_t buf[1024]`, the offset within this buffer and
the length of expected string.
The second issue is when control block is prepended with a byte that
matches first ID character, e.g. there is `SEGGER RTT` control block ID
is prepended by another `S`, making memory contents be `SSEGGER RTT`. In
that case there was no match found.
Fix that issue by making sure that tested byte is always compared with
first byte of expected control block ID.
While at it, change names of local variables to better describe their
meaning.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Change-Id: I12aa6e202bf12bedcbb888ab595751a2a2518a24
Reviewed-on: https://review.openocd.org/c/openocd/+/7429
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Cores armv8m, e.g. Cortex-M33, can be instantiated without the
optional Security Extension.
In this case, the secure registers are not present and when GDB
try accessing them it triggers a set of errors.
For armv8m cores without security extension, don't provide to GDB
the description of the secure registers.
Change-Id: I254478a4cf883e85b786df3f62c726b2f40d88d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Torbjörn SVENSSON <torbjorn.svensson@foss.st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7402
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With flag --enable-verbose, configure enables compiling some
conditional code that with new gcc triggers an error:
error: '%04x' directive output may be truncated writing
between 4 and 8 bytes into a region of size 5
[-Werror=format-truncation=]
Extend the buffer to contain the full 8 bytes of %04x on a 'int'
and change the limit in snprintf.
Skip the intermediate buffer 's[4]'.
Align the code to the coding style.
Change-Id: Ifc8a6e4686555578a7355a1f6049471fd5e31913
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Karl Hammar <karl@aspodata.se>
Reported-by: Tommy Murphy <tommy_murphy@hotmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/376/
Reviewed-on: https://review.openocd.org/c/openocd/+/7403
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flashing a SAMD21J17D was failing during NVM erase. The samd21
datasheet specifies that one cause of error conditions is executing an
NVM command while the previous command is still running. The solution
is to wait for INTFLAG.READY after a command is issued.
SAMD21J17A was not exhibiting this problem. Perhaps the later silicon
revision has slower NVM erase times.
Signed-off-by: Dan Stahlke <dan@stahlke.org>
Change-Id: I19745dae4d3fc6e3a7611dcac628e067cb41e0f0
Reviewed-on: https://review.openocd.org/c/openocd/+/7391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'vdebug mem_path' is reported in the documentation as
'{Config Command}', but the code sets mode = COMMAND_ANY.
The code of the commands sets some value that is only used during
the init phase, so the documentation is correct.
Change mode of command 'vdebug mem_path' to COMMAND_CONFIG.
Change-Id: Icb940fe382cbc75015273b35dcc8a88fc2a7d0ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7395
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
When target is stopped in WFI/WFE or is in an infinite loop, the
sampled PC will always return the same value.
Command 'profile' requires that distance between min and max PC
should be at least 2, which is not the case for constant PC, and
incorrectly enforces the check through as assert().
Move the code that reads the optional parameters 'start' and 'end'
and check the gap 'end - start' before running the profile.
For self-computed min and max, increase max (or decrease min) to
match the required constraint.
Drop the assert().
Change-Id: I2be8df8568ce8c889923888c492e4f7ce354b16b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/370/
Reviewed-on: https://review.openocd.org/c/openocd/+/7400
Tested-by: jenkins
The implementation of command 'monitor profile' has few
issues:
- the address_space is a signed int, so cannot wrap-around on
space over INT_MAX;
- max address is incremented without check for overflow;
- assert() used on errors instead of returning error codes;
- only handles 32 bits PC;
- output file created and left empty on error.
This patch fixes the first two issues, as a wider fix would be too
invasive and should be postponed in a following series.
Change-Id: Id8ead3f6db0fd5730682a0d1638f11836d06a632
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/370/
Reviewed-on: https://review.openocd.org/c/openocd/+/7394
Tested-by: jenkins
Clang complains about the variable 'orig_dfsr' that can be used
uninitialized both in cortex_a_read_cpu_memory() and in
cortex_a_write_cpu_memory().
The issue is caused by an incorrect error path that used to jump
through 'goto out'. The code after the label 'out' is specific to
handle the case of an error during memory R/W; it is incorrect to
jump there to handle an error during the initialization that
precedes the memory R/W.
Replace the 'goto out' with 'return retval'.
Remove the label 'out' that is now unused.
Change-Id: Ib4b140221d1c1b63419de109579bde8b63fc2e8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7393
Tested-by: jenkins
Commit 35a503b08d ("arm_adi_v5: add ap refcount and add get/put
around ap use") modifies the examine functions of mem_ap, cortex_m,
cortex_a and aarch64 by calling dap_put_ap() and then looking again
for the mem-ap and calling dap_get_ap().
This causes an issue if the system is irresponsive and the examine
fails and left the AP pointer to NULL. If the system was already
examined the NULL pointer will cause a SIGSEGV.
Commit b6dad912b8 ("target/cortex_m: prevent segmentation fault
in cortex_m_poll()") proposes a fix for one specific case and only
on cortex_m.
Modify all the examine functions by skipping look-up for the AP if
it was already set in a previous examine; the target's AP is not
supposed to change during runtime.
Remove the partial fix for cortex_m as it is not needed anymore.
Change-Id: I806ec3b1b02fcc76e141c8dd3a65044febbf0a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 35a503b08d ("arm_adi_v5: add ap refcount and add get/put around ap use")
Reviewed-on: https://review.openocd.org/c/openocd/+/7392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the fix, will see "Can not find free FP Comparator" error log
Change-Id: Id0d91cc02b7055e44d27507f9c05ccd48ff49838
Signed-off-by: Nima Palizban <n.palizban@gmail.com>
Fixes: fb43f1ff4e (target: Rework 'set' variable of break-/watchpoints)
Reviewed-on: https://review.openocd.org/c/openocd/+/7389
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If multiple targets are specified as -rtos <rtos_type>, the
rtos_update_threads was called only if the last target was specified as
rtos, which is inconsistent with other checks of whether or not smp target
is an rtos one.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: Ie52bc6b6c8f841d31b9590fcbc44e985d3cba0eb
Reviewed-on: https://review.openocd.org/c/openocd/+/7244
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When OpenOCD receives a step-execution command from GDB and the target
is configured as rtos=hwthread, OpenOCD reconstructs the thread-info.
However, OpenOCD does not restore the thread id which is currently
selected by GDB. Due to this issue, OpenOCD sends the information of
wrong thread to GDB after the step execution.
This commit fixes the above issue by adding a code to save/restore the
thread id selected by GDB.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: I761a1141c04d48f1290e4f09baa7c7024f86f36a
Reviewed-on: https://review.openocd.org/c/openocd/+/7358
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When OpenOCD receives 'g' packet (read general registers) from GDB and
target is configured as rtos=hwthread, hwthread_get_thread_reg_list is
called. However, it does not check if the register valid or not. Due to
this issue, OpenOCD returns invalid register values to GDB.
This commit adds a validity check to hwthread_get_thread_reg_list. If
the register is not valid, it tries to read the register from the
target.
Signed-off-by: Koudai Iwahori <koudai@google.com>
Change-Id: Iad6424b62124271ec411b1dfc044b57dfc460280
Reviewed-on: https://review.openocd.org/c/openocd/+/7357
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang ignores that xds110_swd_write_reg() is always called with
bit SWD_CMD_RNW in 'cmd' set to zero.
It then complains that the local variable 'value' gets passed by
address to xds110_swd_queue_cmd() and in case of 'read request'
such stack address get stored for later use:
src/jtag/drivers/xds110.c:1363:1: warning: Address of
stack memory associated with local variable 'value' is
still referred to by the global variable 'xds110' upon
returning to the caller. This will be a dangling
reference [core.StackAddressEscape]
To both xds110_swd_write_reg() and xds110_swd_read_reg(), add an
assert() to inform Clang about the state of bit SWD_CMD_RNW.
Change-Id: I7687c055ec71424b642e152f478723a930966e3a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7380
Tested-by: jenkins
The variable retval is assigned a value that is never used.
Scan-build reports:
Although the value stored to 'retval' is used in the
enclosing expression, the value is never actually read
from 'retval'.
Drop the dead assignment.
Change-Id: I11588dee748a55d52aa7f35bc1967b7df55af7fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7379
Tested-by: jenkins
The command should now send the full 5 byte command length, which
includes the command tag (0x19) and the 4-byte baudrate word, instead
of only the last 3 bytes of the baudrate.
Signed-off-by: Nick Kraus <nick@nckraus.com>
Change-Id: Idd6e084efd7492489aa900cdbf08f540944041cb
Reviewed-on: https://review.openocd.org/c/openocd/+/7370
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Thread name loading was not correctly handled if a ThreadX task has a NULL
name.
Signed-off-by: Giulio Fieramosca <giulio@glgprograms.it>
Change-Id: I03071930182bc2585b61ce5d8c67491710883dd6
Reviewed-on: https://review.openocd.org/c/openocd/+/7328
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
target_run_flash_async_algorithm expects the source_buffer to have
at least 2 words reserved for read and write pointers in addition to the
FIFO buffer. If the size of the data to be flashed is <= 8 bytes then
the flash function will fail with "corrupted fifo read pointer" error.
Ensure the allocated buffer is big enough to hold both FIFO buffer and
read/write pointers.
Change-Id: I09c22eaac517b8cfea8e0b463f5deb6b98afd267
Signed-off-by: Simon Smiganovski <simon.smiganovski@fruitcore.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7342
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
armv7m_start_algorithm() saves register values to arch_info->context.
armv7m_wait_algorithm() restores register values from arch_info->context.
Exclude registers with flag exist = false from both loops.
While on it refactor the register restore: introduce 'struct reg' pointer
and dereference it instead of numerous accesses by a full path
from armv7m pointer.
Change-Id: I1600084db84809ee13bcf8e7828b79f8c9ff9077
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7276
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang spots a potential NULL pointer dereferencing that is instead
an incorrect use of an array of pointers:
src/rtos/hwthread.c:254:32: warning: Dereference of null pointer
[core.NullDereference]
(*rtos_reg_list)[j].number = (*reg_list)[i].number;
^~~~~~~~~~~~~~~~~~~~~
The error has not been spotted before because:
- this function is not called for the first core of the SMP node,
- for the other cores on Cortex-A it still returns valid register
value for the first 12 ARM registers, then it diverges.
Also Valgrind does not spot any issue at runtime.
Address the array correctly.
While there, use DIV_ROUND_UP() macro for the computation.
Change-Id: Ib87e60e0edfd9671091f5dcfa9aedaf1aed800d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7337
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 0cedf10f8f ("Remove duplicate of a counter in
hwthread_update_threads") introduced a code bug.
In the second foreach_smp_target() loop, variable "threads_found"
gets passed to routine hwthread_fill_thread(). By removing the
counting of threads_found from the second loop, the
incorrect thread counter value gets passed to hwthread_fill_thread().
Change-Id: Ie89e53ccd28bb72b6838ef2f12106a1fe8d00994
Suggested-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The autodetection of CMSIS-DAP v2 bulk interface is tricky
as not all adapters conform CMSIS-DAP specs.
If an interface has a string descriptor containing CMSIS-DAP,
then OpenOCD did not insisted on the correct interface class
LIBUSB_CLASS_VENDOR_SPEC.
However the relaxed test caused false autodetection of v2 bulk
interface on some CMSIS-DAP v1 adapters with an additional serial
interface with the string descriptor stupidly containing
CMSIS-DAP text.
Make the test less relaxed, refuse autodetection of the interfaces
with the class number of well known functions including CDC and MSC.
Link: https://sourceforge.net/p/openocd/tickets/368/
Change-Id: I917cb257eb42aab93560cc39c61ec35a60ce52e3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7279
Tested-by: jenkins
Reviewed-by: SilverFox <yyjdelete@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable retval is assigned a value that is never used, as it
is reassigned few lines below.
Drop the dead assignment.
Change-Id: Id4e9134408fab3e04936d36e95724bf8d3ab55aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7304
Tested-by: jenkins
Clang get confused by initializing the array uint16_t lock_word[],
casting it to (uint8_t *), then accessing the second element of
the uint8_t pointer.
src/target/dsp5680xx.c:2046:41: warning: The left operand of '<<'
is a garbage value [core.UndefinedBinaryOperatorResult]
uint16_t tmp = (buffer[0] | (buffer[1] << 8));
~~~~~~~~~ ^
Fix it by replacing the array with a single uint16_t.
The code is still depending on host endianness; no fix for this is
proposed.
Change-Id: I16dfd60cab117dd145aeecf10d9593574ff233a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7302
Tested-by: jenkins
The function esirisc_jtag_recv() can be called with argument
num_in_fields = 0, for example as consequence of calling
esirisc_jtag_continue().
In this case, num_in_bytes is zero and the allocation of the
variable-length array 'r' requires size zero.
src/target/esirisc_jtag.c:133:2: warning: Declared variable-length
array (VLA) has zero size [core.VLASize]
uint8_t r[num_in_bytes * 2];
^~~~~~~~~ ~~~~~~~~~~~~~~~~
Fix it by forcing size one when num_in_bytes is zero.
Change-Id: Id764c7b5ec4f5b3c18c7da650bbff39fc98ed049
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7301
Tested-by: jenkins
Clang assumes that size could assume a value that is not 1 nor 2
nor 4. In such condition the buffer in t is allocated (size != 1)
and not initialized. This triggers an error:
src/target/openrisc/or1k_du_adv.c:655:14: warning: 2nd function
call argument is an uninitialized value [core.CallAndMessage]
crc_calc = adbg_compute_crc(crc_calc, data[i], 8);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add the default case to cover other values of size.
After this fix, clang still complains on the same line, this time
misunderstanding the limits of the loop and considering that
buf_bswap16() only swaps the first 16 bits, thus passing not
initialized value data[2] to adbg_compute_crc()
Replace malloc() with calloc() to silent it.
Change-Id: I358d7fb2ebefd69255670641bd435b770762a301
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7300
Tested-by: jenkins
All the converters functions:
h_u64_to_le()
h_u64_to_be()
h_u32_to_le()
h_u32_to_be()
h_u24_to_le()
h_u24_to_be()
h_u16_to_le()
h_u16_to_be()
have signed type in their prototype, while the function name and
all the current use cases pass an unsigned value.
Change the prototypes to use unsigned types.
Change-Id: I76dcfdd7912b81f60902184712b2907eae9843f7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7299
Tested-by: jenkins
If we just invented thread 1 to represent the current execution, we
need to make sure the RTOS object also claims it's the current thread
so that threadx_get_thread_reg_list() doesn't attempt to read a
thread control block at 0x00000001.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I7f71e730d047858898297e4cb31db8e47e0c371c
Reviewed-on: https://review.openocd.org/c/openocd/+/7280
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
`xtensa_do_step` is invoked from `xtensa_prepare_resume` to silently
step over BP/WP before resuming.
For example; in the case of WPs (DEBUGCAUSE_DB), in the current
implementation `xtensa_do_step` will generate one more
`TARGET_EVENT_HALTED` after the original one caused by WP itself.
This patch moves the halted event cb call after
the step is done successfully.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I9048e14fb316dc124847a42cfaefb1f76b5ce53e
Reviewed-on: https://review.openocd.org/c/openocd/+/7274
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Fix the declaration of riscv command 'set_mem_access'.
- Remove non existing riscv command 'set_scratch_ram'.
- Add riscv commands 'info', 'reset_delays'; copy the description
from the 'help' text.
- Don't add riscv commands 'set_prefer_sba' and 'test_sba_config_reg'
as they are marked as deprecated.
- Ensure that 'test_sba_config_reg' prints a deprecation warning
when used.
Change-Id: I39dc3aec4e7f13b69ac19685f1b593790acdde83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7268
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
This GPIO driver is common to SoCs that have in-order ARM cores
(BCM2835) as well as superscalar (BCM2836-7) and speculative
out-of-order cores (BCM2711).
For BCM2837 and BCM2711, the processor can dual-issue stores and
is free to merge writes to peripheral memory for pages mapped
MT_NORMAL_NC, which is the default provided by /dev/[gpio]mem.
This can cause glitches (or missing edges) on GPIO pins when
toggled with no delay, as pipelined writes to the same address
can get arbitrarily squelched.
To prevent this happening, make sure the preceding write ops are
flushed outside the shareable domain by using a memory barrier.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Change-Id: I8805cc0911667bcb9b7f4ca340d7f4f1cb25d096
Reviewed-on: https://review.openocd.org/c/openocd/+/7258
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Currently 'number' field is zero in the register cache and
this causes an issue on `rtos get_thread_reg_list` calls.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Iaef11e01f55d012969bbc1933f82847d5e02fec5
Reviewed-on: https://review.openocd.org/c/openocd/+/7246
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
arp_waitstate will not work on not-examined state
Change-Id: I56c3e1c7e63af108e4ed1dbacebb567f9bf46264
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7230
Tested-by: jenkins
Reviewed-by: Erwan Gouriou
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: I7c3de39fb1e6c23b76e2a0a85ab75f23aac94c4d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
An application often idling in real sleep mode may make a Cortex-M target
hard to access as CPU clock are gated and debug requests are responded
by WAIT ack.
Try to examine the target under reset as the last resort.
Change-Id: Ife875a966a838c37dde987bc584ad0a1f4d020d6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After merging [1] 'reset halt' does not work on not responding Cortex-M.
Relax the examined tests and try to set vector catch VC_CORERESET
if debug_ap is available.
While on it add an info about examination state to debug logs.
Fixes: [1] commit 98d9f1168c ("target: reset target examined flag if target::examine() fails")
Change-Id: Ie2e018610026180af5997d70231061a275f05c76
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6745
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For 64-bit TAR setup, if 'tar_valid == false' perform the upper 32-bit
write even if the cached copy matches the upper TAR value to be written.
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Change-Id: I320377dc90a9d1d7b64cbb281b2527e56c7621ee
Reviewed-on: https://review.openocd.org/c/openocd/+/7245
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Read values must be at albuff so that can be copied to buffer
on function exit.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I74a533e8f12f1002ca06a98a7c7cd928552b4cc5
Reviewed-on: https://review.openocd.org/c/openocd/+/7226
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Actually they are the base of epc and eps
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I4f43b9609a9929399fb5d3fa0203efc8a98e94c9
Reviewed-on: https://review.openocd.org/c/openocd/+/7227
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ST-Link v2 dongles can be used with many cortex-m parts, but they have
one limitation -- they can only perform 8-bit and 32-bit writes to the
target. 16-bit writes are done using a pair of 8-bit writes. While not
usually an issue, in the case of the at91samd flash driver, the 16-bit
'command' register must have both halves written in the same
operation.
Fortunately, this register has two pad bytes above it in the address
space, making it safe to always access with 32-bit operations.
Change-Id: I44b0db9406982a8db5818c0533d3101618741db2
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7234
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There is no need to count number of examined threads twice.
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Change-Id: Id32ead853d1ddcd4e67062d6f795700feb20cb4b
Reviewed-on: https://review.openocd.org/c/openocd/+/7223
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The bitbang driver floods the log by many messages with very
little informational value.
Remove some LOG_DEBUGs, convert some others to LOG_DEBUG_IO.
Change-Id: I0c7539467b45543e12932c67dc71e86d58c8c6cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7220
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Make write to DP_TARGETSEL is logged the similar way as other DP register
read/writes.
While on it fix checkpatch message
'Concatenated strings should use spaces between elements'
Change-Id: I98f724c984e8c4610cc461340f4c4a7cc9627ed9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7219
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
armv7m_start_algorithm() stored all non-debug execution
registers from register cache without checking validity.
Check if the register cache is valid.
Try to read from CPU if not valid.
Issue a warning if register read fails.
Change-Id: I365f86d65243230cf521b13909575e5986a87a50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7240
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The num_reg_params parameter of target_run_algorithm() was not
updated when setting "sp" was introduced. Therefore "sp" as the last
register parameter was not passed to a target algo.
Introduce a new helper variable with correct count of register parameters
and use it everywhere needed.
Change-Id: I934a71380783d98917167f1569145808ef23540f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7225
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Change-Id: Idf3bce842b4507c1f12692b5fbcd6730637de9db
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7216
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Flash read_id/erase/write operation on running target failed
in target_run_algorithm() anyway. It generated lot of error messages.
Check the target state and bail out early if target is running.
Change-Id: I903f5f38c8e61016e5002b235e5f07803bd2ec4e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7215
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
SPI flash erase often takes longer than the fixed timeout 3 seconds.
Introduce a configurable timeout_ms parameter to rp2040_call_rom_func().
Compute the erase timeout from the number of blocks to be erased.
While on it make the timeouts shorter for connect flash, flush cache and
enter/exit xip (1 second is enough).
Change-Id: I552bfa317ee17064de3a54ec2f0c63e84ba87222
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7214
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The size of the flash write buffer should be rounded
down to the multiply of flash page size.
Using write chunks of unadjusted size results in write of chunks
unaligned to flash pages.
Change-Id: If7931362ee193dff4dc2df7ec78f13530658cf08
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7187
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it restore memory-mapped mode also after flash erase
(originally was restored after flash write only).
Change-Id: I5e153b79ac27a8439f57239ce90ce8a79c0bb8a1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7186
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Prepend stack_grab_and_prep() function name by rp2040_ prefix.
Introduce target helper variable in rp2040_stack_grab_and_prep()
and use it instead of dereferencing bank->target several times.
Move flash ID reading code to the new rp2040_spi_read_flash_id()
function.
Change-Id: I9d6e51e17e36e6230155a586065499f2f260089a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7185
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
swd_multidrop_select() uses its own retry loop.
If select fails, do_reconnect flag remains set on exit and causes
useless reconnect.
Clear do_reconnect flag in retry loop.
Change-Id: Ie06d6967d7f4a977774c8530bb8d4b3e5ab4f62c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7217
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Tested-by: jenkins
Implementation of ADI v6 introduced banking of DP reg 0.
The accompanying change preventing DP SELECT write before
DP IDR read during connect was added to swd_connect_single() only.
Unchanged swd_connect_multidrop() / swd_multidrop_select_inner()
was broken as it emited DP SELECT and put DP to protocol error state.
Copy dap->select handling to swd_multidrop_select_inner().
Fixes: 72fb88613f (adiv6: add low level swd transport)
Change-Id: I514cd6d9ae2ba97ce3657b459df22638c278a0b1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7213
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Increase "value_buf" size so it can hold a 64-bit number represented
as a string. Previous size could only hold a 32-bit number string.
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Change-Id: If6fbc875236e6ddc59522fbc25db0129eb60ee27
Reviewed-on: https://review.openocd.org/c/openocd/+/7221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Scan-build reports:
Logic error: Uninitialized argument value
riscv.c:2688 2nd function call argument is an uninitialized value
This is a real error cause by running the command "riscv
authdata_write" without arguments. In such case 'value' is not
initialized and is passed to and used by r->authdata_write().
Reorganize the code to:
- detect the correct amount or command's arguments;
- drop the LOG_ERROR() on ERROR_COMMAND_SYNTAX_ERROR;
- drop the 'else' after 'return'.
Change-Id: I62e031220593b8308bc674b753e15d16d4c5c9ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7210
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Scan-build reports:
Logic error: Result of operation is garbage or undefined
riscv.c:1614 The result of the left shift is undefined due
to shifting by '4294967281', which is greater or
equal to the width of type 'target_addr_t'
This is a false warning due to clang that considers the impossible
case of 32 bits hart (xlen = 32) in SATP_MODE_SV48 mode
(info->va_bits = 48).
Under such case:
riscv.c:1614 ... ((target_addr_t)1 << (xlen - (info->va_bits - 1))) ...
the shift amount wraps around the unsigned type and assumes the
value 4294967281 (0xfffffff1).
Use assert() to prevent clang from complaining.
Change-Id: I08fdd2a806c350d061641e28cf15a51b397db099
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7209
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead nested assignment
riscv.c:459 Although the value stored to 'ir_user4_raw' is
used in the enclosing expression, the value is
never actually read from 'ir_user4_raw'
This is caused by the value reassigned in 'ir_user4_raw':
riscv.c:459 ir_user4[3] = (uint8_t)(ir_user4_raw >>= 8);
but never used.
Drop the DIY conversion in favor of h_u32_to_le() that does not
reassign the input value.
Change-Id: Ifad29f4c46d4a2d0a2f5a5c4104d768cc3db2794
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7208
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead assignment
riscv.c:716 Value stored to 'result' is never read
Remove the initialization of variable 'result'.
Change-Id: Ied67bb4fcfa5bace186522074247ead43a5d5cd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7207
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build reports:
Unused code: Dead initialization
riscv-013.c:2362 Value stored to 'control' during its
initialization is never read
Remove the initialization of variable 'control'.
Change-Id: I548f8175530b9a2aa4c1788549d6467bf9824584
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7206
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build complains about variable 'sbcs_orig' that can be used
not initialized.
Logic error: Assigned value is garbage or undefined
riscv-013.c:4468 Assigned value is garbage or undefined
This is caused by not checking the return value of the call
riscv-013.c:4466 dmi_read(target, &sbcs_orig, DM_SBCS);
In fact when dmi_read() returns error, the variable 'sbcs_orig' is
not assigned.
Check the returned value.
Change-Id: Ia9032a0229aa243138f95f4e13f765726a4ceae9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7205
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Tested-by: jenkins
Scan-build triggers a warning:
Unix API: Allocator sizeof operand mismatch
dsp563xx.c:2143 Result of 'calloc' is converted to a pointer
of type 'uint8_t', which is incompatible with sizeof
operand type 'uint32_t'
It's a false positive because calloc() is properly used in this
case, as the uint8_t array is used in blocks of 4 elements to read
or write uint32_t values.
Either
calloc(sizeof(uint32_t), count);
and
malloc(count * sizeof(uint32_t));
keep triggering the same warning.
Drop the warning by using the constant '4' as size of uint32_t, as
already used few lines below.
Change-Id: I5bb1ece177774eefdc5d9cd049338f8f2be87cd7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7203
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Doxygen complains about:
adapter.h:120: warning: Unsupported xml/html tag <signal_name> found
Move the text in double quote to remove the warning.
Change-Id: Ia4ead5caa83c84e10ee2b2359048c282892170b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 82fd400542 ("jtag/adapter: Add command 'adapter gpio'")
Reviewed-on: https://review.openocd.org/c/openocd/+/7202
Tested-by: jenkins
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Resolves issues where registers are accessed when poll() logic is inactive or has not yet been triggered.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: If7a4d00938fb188b008325249627f7773c3484c5
Reviewed-on: https://review.openocd.org/c/openocd/+/7197
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When FreeRTOS (at least) is compiled with -flto, this leaves certain
static symbols with .lto_priv.0 appended to their name. Arguably this
could be considered to be a gdb or gcc bug, but one place to resolve it
for OpenOCD usage is here at symbol lookup time.
Note that the ".0" is for the first such instance of the variable as a
static; additional ones would end up as ".1", ".2", etc, and are not
considered here.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: I03580b45e8ea364392ef4e05c96276416b390cb0
Reviewed-on: https://review.openocd.org/c/openocd/+/7179
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is in preparation for a future commit that looks for an optional
suffix of .lto_priv.0 on the symbol name.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: If803332373825b73bc986bd4ea7dfaee9c625c0a
Reviewed-on: https://review.openocd.org/c/openocd/+/7178
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This will be utilized for an upcoming refactorization to support -flto
compiled programs.
Signed-off-by: Tim Nordell <tnordell@airgain.com>
Change-Id: Id523c0b3ac2dad8b248ea0d2cac7b4dd2f83d293
Reviewed-on: https://review.openocd.org/c/openocd/+/7177
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Read PS from EPS[debuglevel] during fetch such that it reflects the correct value when read via telnet (not just via gdb_server).
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I8504f68989bc6d5fe451a8cb69d01c86f4ec0100
Reviewed-on: https://review.openocd.org/c/openocd/+/7195
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This updates the FreeRTOS module to use the M4F FPU stacking also for the
FPV5_SP and FPV5_DP FPUs, which are found on the Cortex-M7. The FPUs are
in fact different than the FPV4_SP found on the M4, but the register
stacking is the same.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I74c45d2cfb55f55e6c557f2450068ad3c2fe9497
Reviewed-on: https://review.openocd.org/c/openocd/+/6939
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The method soft_reset_halt is optional; no need to add an
empty function.
Remove mips_mips64_soft_reset_halt() and move the TODO comment
in struct target_type.
Change-Id: Id541a75e7a08645568961d59b73a120c2238701f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7184
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Read buffer is sized for 32-bit APB version of PWRSTAT/PWRCTL registers. Initialize to zero so 8-bit JTAG register mirrors are accurate.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I81310649fa7180893d0188aab3c8a14315aaea0a
Reviewed-on: https://review.openocd.org/c/openocd/+/7183
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I2b6a8365f554e332520fa77ccf076188083a932f
Reviewed-on: https://review.openocd.org/c/openocd/+/7122
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
New GCC reports 5 warning:
src/jtag/drivers/ep93xx.c: In function 'set_gonk_mode':
src/jtag/drivers/ep93xx.c:123:47: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
123 | devicecfg = *((volatile int *)(syscon + 0x80));
| ^
src/jtag/drivers/ep93xx.c:124:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
124 | *((volatile int *)(syscon + 0xc0)) = 0xaa;
| ^
src/jtag/drivers/ep93xx.c:125:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
125 | *((volatile int *)(syscon + 0x80)) = devicecfg | 0x08000000;
| ^
src/jtag/drivers/ep93xx.c: In function 'ep93xx_init':
src/jtag/drivers/ep93xx.c:182:46: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
182 | gpio_data_register = gpio_controller + 0x08;
| ^
src/jtag/drivers/ep93xx.c:183:56: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
183 | gpio_data_direction_register = gpio_controller + 0x18;
| ^
Change pointer type to allow pointer arithmetic.
Change-Id: Idd78a7156bdf99df2624043e924b8e54a0588ace
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7180
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change") replaces the jimtcl command "expr" with an openocd
version that detects the TCL syntax change and prints a warning.
The openocd "expr" command will be dropped after v0.12.0,
One side effect is that openocd invokes polling the target after
every openocd command, causing scripts that use several "expr"
commands to run much slower; see [1].
The proper fix would require openocd to invoke polling only at the
time period deadline, instead of at each command. Such fix is too
risky to be applied now, due to short time before v0.12.0-rc1.
As a temporarily workaround, let openocd to detect the "expr"
command and skip the polling.
This will be dropped together with the openocd "expr" command.
Change-Id: I8151aa28694817001046165a15475d64896f985e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/362/ [1]
Fixes: c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr' syntax change")
Reviewed-on: https://review.openocd.org/c/openocd/+/7174
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not used outside the file should not be exported
and should be declared as static.
Change-Id: Icbe7f7bce287b903edec9dc9db3370722c51fbd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7173
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Variables should not be declared in the include file, otherwise
multiple include will cause multiple instances.
Move the declaration in the C file and make it static.
Change-Id: I8b4884cba643a792a78df4e123aa324b19d92279
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7172
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Move the existing comments to the static declarations.
Change-Id: Idf208e3fda4b3f8df789553cf03ebf5f20d811bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7170
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I6a059080bbba9b3559d26c641b217be8be3b199e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7169
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: I2475524f4c14520e3163572560f4a9f276356ed5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7168
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not exported should be declared as static.
Change-Id: Ieb627f7f896e4663b0d5b18c4ab1853b39d23d03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7167
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Tested-by: jenkins
Symbols that are not exported should be declared as static.
Change-Id: Ie3bd17535c8cb2a0fec5d3bedfe7de3e0a702613
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7166
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Symbols that are not exported should be declared as static.
Change-Id: I6224ae89ebda3230dfee2413e3823be9b8716bba
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7165
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The function set_log_output() has never been used after the drop
of eCos build with commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") in 2012.
Drop it!
Change-Id: I070b688061776c7ced5db18f738d78a4a7623726
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7164
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For some configurations, notably on DAP systems, resolve issue where single-stepping does not always transition into the HALTED state.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I053f4eaffad8c3228878ba87580ada640e4bd2fe
Reviewed-on: https://review.openocd.org/c/openocd/+/7150
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Enable ADIv5 DAP systems via JTAG or SWD transport
- Select correct PWRCTL/PWRSTAT bits for XDM/APB
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I5894210c804f85075da868d0cfc6fb20b589d99f
Reviewed-on: https://review.openocd.org/c/openocd/+/7144
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We have left the camelcase symbols *xPSR* for some time, to avoid
any conflict with possibly pending patches in gerrit.
With the approaching v0.12.0-rc1, it's time to revisit it.
The patches in gerrit that conflict with this rename are all not
merge-able due to conflicts or due to negative review.
Drop these CamelCase symbols.
Change-Id: Ifbac4c1df9cc55994e024971a2aaebeed2ea4ed3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the help of checkpatch, some CamelCase symbol passed
through the filter of maintainer's review.
Drop them.
Change-Id: If5fb07b2ffb89e853dd2a61f20d4134aa6e20d24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 48f267d4ad ("flash/stm32l4x: avoid using magic numbers for device ids")
Fixes: 5ab74bde06 ("semihosting: User defined operation, Tcl command exec on host")
Reviewed-on: https://review.openocd.org/c/openocd/+/7154
Tested-by: jenkins
Use indirect enum IDs to access XDM registers in preparation for supporting both NAR (JTAG) and APB (DAP). No new clang static analysis warnings.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I0b742fe4661ff3cf609454b8650493d141a1e1ff
Reviewed-on: https://review.openocd.org/c/openocd/+/7143
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
As a follow-up of talks between JEDEC and STMicroelectronics,
JEDEC agrees to let OpenOCD project including the manufacturer's
identification code list extracted from JEDEC JEP106 document and
to let OpenOCD being updated regularly using the future JEDEC
JEP106 document versions. JEDEC requires OpenOCD to report the
origin of the JEDEC JEP106 manufacturer's identification code list
together with the JEDEC copyright.
As agreed with JEDEC, add in the file jep106.inc:
- the SPDX tag with the GPL license of the OpenOCD project;
- the JEDEC copyright;
- the text provided by JEDEC reporting the origin of the JEDEC
JEP106 manufacturer's identification code list.
While there:
- add a line reporting the version of the JEP106 document that was
used for the current code list extraction;
- remove the obsolete comment, as the script for extraction is not
working anymore; keep the script as example.
Change-Id: Iaa76716db14e15ffca04fcf7d8c27bb85a27ba10
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The full text of the license is already available in the file
LICENSES/preferred/BSD-2-Clause
and there is no need to replicate it in the source code.
Remove the BSD-2-Clause boilerplate but, preserved the copyright
notice because it provides the info on the copyright holder.
Change-Id: I162aa4ad06b551f1a71a28d049cb797ee8ab5a01
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7146
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
In the app-trace module we are polling the target in the while loops
outside of the server.c
In that loops, we need to catch ctrl+c signal by checking shutdown_openocd
status
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Id87c709a01470bf6d3642078b160a68ca85f4406
Reviewed-on: https://review.openocd.org/c/openocd/+/7142
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested with an PLUS-F5270 board which uses the MM32F5277E9PV.
Signed-off-by: iysheng <iyysheng@gmail.com>
Change-Id: Icb75ae8337fdc6fa60e39d3d74dd8bc163707bdd
Reviewed-on: https://review.openocd.org/c/openocd/+/7136
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
kinetis.c:994:61: error: '%u' directive output may be truncated
writing between 1 and 10 bytes into a region of size 4
[-Werror=format-truncation=]
tested with scan-build-14
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I72d141a3f8e19ca3596beee2be8434fc8492946f
Reviewed-on: https://review.openocd.org/c/openocd/+/7140
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Scan-build of target/xtensa/ has no clang analyzer warnings from xtensa source files.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I11a125c923ece9a6fd0d9ee1698f742f88ee5cab
Reviewed-on: https://review.openocd.org/c/openocd/+/7141
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While on it rename misleading write_algorithm_sp to write_algorithm_stack
and change messages referring 'stack pointer' instead of stack.
No functional change.
Change-Id: Ibb9897d3f01734812ed0f8bc8cd43b935a573f8a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7132
Tested-by: jenkins
Reviewed-by: Salvatore Giorgio Pecorino <salvatore-giorgio.pecorino@st.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
FLASH_MAX_ERROR_STR is not used since commit 815c3b3533
(merged in ~2008)
Change-Id: Ic117a2e3d22235c31dc14533b6564ebf5a13ae58
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7121
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The value of struct flash_driver::command can be NULL when the
flash driver does not need to add any new command.
Remove empty command definitions.
Change-Id: I5413967d4069030234469822d24e9825425ae012
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7120
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The change 6363: Call poll at a fixed interval
switched from target_call_timer_callbacks() to target_call_timer_callbacks_now().
It breaks the timing as all timers callbacks are called every time
one timer expires.
Revert this part of change and use target_call_timer_callbacks().
Fixes: db16b3dc5b (Call poll at a fixed interval.)
Change-Id: Ib5b7774de9694d40c55d2a4109d0d1582fc5008b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7118
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since commit 88f429ead0
5321: target/cortex_m: faster reading of all CPU registers
debugging with a kitprog adapter freezes at debug entry.
How to replicate:
openocd -f interface/kitprog.cfg -f target/psoc4.cfg
Connect to telnet server.
Make sure the target is running:
resume
Halt the target:
halt
Without this patch OpenOCD freezes in kitprog_hid_command()
in library call hid_write().
Reduce the number of SWD transactions sent in one USB bulk write
as a workaround, simply use shorter buffer.
For details see the comment in src/jtag/drivers/kitprog.c
Change-Id: I0116894d5ebf1655f6011f0d35acdbbc178cd48c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7107
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When printing memory sizes standard ISO 80000-1 prefixes should be used.
Also a space should be added between any number and its unit according
to papers publication rules.
Change-Id: Id1d35e210766b55c201de4e80ac165d8d0414d0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix Unused code Dead assignment at line 657
Fix Memory error Double free at line 2851
Fix Memory error Memory leak at line 2530
Fix error: 'a3' may be used uninitialized at line 758
Fix error: '%04x' directive writing between 4 and 8 bytes
into a region of size 5 at line 2471
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I0382a622bc7c4108a335fd741816577e79240397
Reviewed-on: https://review.openocd.org/c/openocd/+/7137
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Also used type helper (PRId64) to specify format of int64_t
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I594863eab594aff621c26fefcc69a1872e9730ee
Reviewed-on: https://review.openocd.org/c/openocd/+/7111
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some files have author info some doesn't. For the consistency we removed all.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie6f1ec012302e3a954c75c5106f12820722cb715
Reviewed-on: https://review.openocd.org/c/openocd/+/7104
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Change-Id: I9466edd2f43791e64f2dce719957c67728f3ec06
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Most adapters define their own commands to obtain the GPIO number and
other GPIO configuration information such as chip number, output drive
type, active high/low.
Define a general command 'adapter gpio' as replacement for the
driver-specific ones.
Change-Id: I1ca9ca94f0c7df5713172e9f62ffb0ad64e9ee97
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6967
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The S_RESET_ST sticky bit is reset after DHCSR read.
It is set at power-on reset and keeps active until the debuger reads DHCSR.
Ignore S_RESET_ST at the very first read after OpenOCD start
and suppress possibly misleading message "external reset detected"
if we cannot guarantee the reset happened recently.
While on it add a TODO comment.
Change-Id: I15217c2ca6f69ac97aff8be86bce67cba94a42cd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7109
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide a customizable hook for handling target-specific GDB queries
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I684a259ed29f3651cbce668101cff421e522f79e
Reviewed-on: https://review.openocd.org/c/openocd/+/7082
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add additional error handling for targets where gaps may exist in reg_list[]
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I65232429e2de08f5d54eeca53aea0db8ce2b58af
Reviewed-on: https://review.openocd.org/c/openocd/+/7103
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The command 'init' causes the execution of few lower level
commands, e.g. 'target init', and switches from command mode
COMMAND_CONFIG to COMMAND_EXEC, with an intermediate switch back
to mode COMMAND_CONFIG.
A timed target polling can occur during the execution of 'init'
and the target's status can trigger the execution of some events.
E.g. if a target has been left halted by a previous execution of
OpenOCD, the first poll will find the target halted, calling the
corresponding 'halted' event.
The event handler can use commands that can only be executed in
mode COMMAND_EXEC. If the poll happens while OpenOCD is in mode
COMMAND_CONFIG, the triggered handler will fail.
Prevent the target polling to operate during the execution of the
'init' command.
Change-Id: Ia435a5d2039be9b247e2336616dab53ed5d983ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7007
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The same flag 'jtag_poll' is currently used as local data for the
command 'poll' and to temporarily mask the target polling.
This can cause unexpected behavior if the command 'poll' is
executed while polling is temporarily masked.
Add a new flag 'jtag_poll_en' to hold the temporarily mask
condition and keep 'jtag_poll' for the 'poll' command only.
While there, change the initial assignment of 'jtag_poll' using
the proper boolean value.
Change-Id: I18dcf7c65b07aefadf046caaa2fcd2d74fa6fbae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
GDB remote serial protocol specifies breakpoint/watchpoint packet
responses can be an empty string to indicate the specified breakpoint
type is not supported. Add support for this response alongside existing
"OK", "E NN" replies.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: Iaf6280e4c936eb95a92bc80cc74d451ebb328dc3
Reviewed-on: https://review.openocd.org/c/openocd/+/7102
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After a certain RTOS has been configured there is no mechanism
to go back to no RTOS support. It may be useful for debugging
purposes. With the provided modification, the "none" option
of RTOS is provided as a valid option.
It has been tested in two different board (Cortex M4 and Cortex M33).
Documentation has also been updated.
Signed-off-by: Asier Llano <allano@hubbell.com>
Change-Id: I602210bff31ccadd41c41e9454c52b5fffa1671e
Reviewed-on: https://review.openocd.org/c/openocd/+/7092
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This one doesn't have the license in there, which means now it's
acceptable to GPLv2 again.
See https://github.com/riscv/riscv-openocd/pull/711
Change-Id: I8ba27801172ffa955470d2627fa656cad282ee99
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7087
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tcl commands 'arm reg', 'arm mcr/mrc' do not work on M-profile based devices.
Isolate them from 'arm core_state' and 'arm disassemble' and do not chain
them from armv7m_command_handlers.
Change-Id: I2c6befdf82575e95cf05ed158ab5e6faa1a182c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7101
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tcl command 'arm core_state' was exposed even on Cortex-M devices.
However it returned message "Unsupported Command" without error status
on such device.
Set the only possible arm->core_state ARM_STATE_THUMB in armv7m init.
Block setting core_state to arm on Cortex-M.
Change-Id: I9525553ac8863a6cf77bbacbcd57e354b6cfe1ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7100
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If a Cortex-M MCU become unresponsive during a debug session and
re-examination fails to find MEM-AP, debug_ap pointer is set to NULL.
Eventual call of cortex_m_poll() dereferences debug_ap.
Check debug_ap validity at the begin of cortex_m_poll().
Change-Id: I9519f48760c91a48a9e5e8c34634d247098cb14a
Fixes: 35a503b08d (arm_adi_v5: add ap refcount and add get/put around ap use)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Just a cosmetic refactoring.
Change-Id: I7fbc05324e346fafc98d1b42691d33d3d8fbd04e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7003
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
AARCH64_COMMON_MAGIC was same as CORTEX_A_COMMON_MAGIC, probably copy pasta.
Define unique AARCH64_COMMON_MAGIC
Change-Id: Ie30e0028453a1fce5624ecad9bf73d5ac3791281
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6997
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Unify common_magic type to unsigned int
Move common_magic to be the first member of the struct
Add unsigned specifier to xxx_COMMON_MAGIC #defines
Change-Id: If961d33232698529514ba3720e04418baf6dc6fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6996
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The flash/nor subsystem uses bus_width and chip_width for CFI
external flash only. Drop setting these values for internal flash.
Change-Id: I64e79ab38b6e39e845ff96fbf4f60145e3b9690a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7098
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The working area allocation routines use 4 byte word alignment.
In the corner case the size of the working area is not aligned,
target_alloc_working_area() of size = target_get_working_area_avail()
will fail because the size gets aligned up and does not fit to the area
which size is aligned down.
Align down the result of target_get_working_area_avail() to cope with that
corner case.
While on it use fancy ALIGN_... macros instead of bitwise and operator.
Change-Id: Ia2a1e861c401c2c78fe6323379a3776fb4f47b06
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7096
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Kinetis 100 MHz rev 1.x devices have no SMC and hence need different
checking of the run mode. Details about the differences between rev 1.x
and 2.x of the Kinetis 100 MHz series can be found here:
https://www.nxp.com.cn/docs/en/application-note/AN4445.pdf
Signed-off-by: Martin Hierholzer <martin.hierholzer@desy.de>
Change-Id: Ib705385a931275159bdae9b31caecc6ec9c0da1e
Reviewed-on: https://review.openocd.org/c/openocd/+/7015
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Previously, if the target was halted before the FreeRTOS scheduler was
started but after at least one thread was created, then the current thread
would be set to whichever thread had the highest priority. In addition to
being misleading, because that thread is not actually running, it can
cause issues with gdb. For instance, breaking somewhere before the first
thread is created will show the current execution as the current thread,
but stepping over a line that creates a thread will cause the current
thread to switch to the newly created thread and the current execution to
disappear. The sudden disappearance of the current execution thread seems
to confuse some versions of gdb.
With this change, the value of xSchedulerRunning is checked to determine
whether the scheduler has been started. If it hasn't, then a fake
'current execution' thread is always created and made the current thread.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: Ide0fe7d9ffb9fac95cee4c805735f434c7c4934d
Reviewed-on: https://review.openocd.org/c/openocd/+/6935
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When there are no rtos threads or none are active, a fake thread with
ID 1 is created for the current execution, but the current thread ID was
never set to this new fake ID. This would lead to an incorrect attempt to
read stacked registers for this fake thread. Explicitly setting the
current thread ID to the fake ID ensures that the registers are read from
the core instead of calling freertos_get_thread_reg_list.
Signed-off-by: Frank Dischner <frank.dischner@gmail.com>
Change-Id: I694509a0e01df089429b20ff1b879fc0592b532d
Reviewed-on: https://review.openocd.org/c/openocd/+/6934
Tested-by: jenkins
Reviewed-by: Asier Llano <asierllano@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make the main RISC-V structure more compliant with OpenOCD coding style.
Other typedefs remains as is.
Change-Id: I5657ad28fea8108fd66ab27b2dfe1c868dc5805b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6998
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
We found that the NPCX has an issue with the byte lanes so that non byte
aligned writes aren't working. To overcome this, for byte accesses we
copy the byte to be written to all of the byte lanes.
doc: Document command nu_npcx_quirks
Signed-off-by: benjbender <benjbender@gmail.com>
[Andreas Fritiofson: Squashed commits]
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I9ef63bf692f4e68f57459e1ec33f3abcbf533cd2
Reviewed-on: https://review.openocd.org/c/openocd/+/6630
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for DAP interface to Cadence vdebug driver.
It implements a new transport layer for dapdirect_swd.
Change-Id: I64b02a9e1ce91e552e07fca692879655496f88b6
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6965
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Jason Peck
Nishanth Menon
Bruno Mendes
Karl Palsson
Nikolay Dimitrov
Daniel Anselmi
Daniel Goehring
Ahmed BOUDJELIDA
Antonio Borneo
Parshintsev Anatoly
Marek Vrbka
Tomas Vanek
Tim Newsome
eolson
Artemiy Volkov
Erhan Kurubas
Marc Schink
Laurent LEMELE
iosabi
Jacek Wuwer
Bohdan Tymkiv
Ian Thompson
Jan Matyas
Matthijs Kooijman
Amaury Pouly
Tarek BOCHKATI
Paul Fertser
Julien Massot
panciyan
François LEGAL
Chao Du
Kai Schmitz
Peter Collingbourne
Andrew Lalaev
Andreas Bolsch
Daniel Serpell
N S
Andreas Fritiofson
Marian Buschsieweke
Jian-Hong Pan
Zale Yu
Boris-Chengbiao Zhou
Tarek BOCHKATI
Jan Matyas
Koudai Iwahori
James G. Smith
Fawaz Tirmizi
Kyle Schwarz
Marcin Niestroj
Dan Stahlke
Nima Palizban
Evgeniy Naydanov
Nick Kraus
Giulio Fieramosca
Simon Smiganovski
Ben McMorran
Jonathan Bell
Keith Packard
Tim Nordell
Toms Stūrmanis
Frank Dischner
Steve Marple
Antonio Borneo
iysheng
MadSquirrel
Asier Llano
Martin Hierholzer
Ben Bender