Adapted from diolan_lpc4350-db1.cfg. Both boards are identical except
for the SoC, so keep them in sync.
Change-Id: If892d8e953b0e3a9209a95b3b23a547357c10b7a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3038
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reuse the flashless LPC4350 as base and amend it as necessary.
The LPC43x7 have 2x 512 KB of flash.
Change-Id: Ia7ffbc7101023479971984b839f171ed4be6b089
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3037
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add support for the JTAG TAPID found on SK-FM4-U120-9B560-MEM V1.1.0 board.
Change-Id: Idbfe28927e0c549f0c89c29904d23971281927c9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3039
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It is found on the SK-FM4-U120-9B560-MEM V1.1.0 among others.
Change-Id: I4c708c9391e954cbbc8d0860a2a2dbd264aea865
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3008
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Its memory layout is different from MB9BFxxx.
Change-Id: I39c9f9cf582cd182971a9f83bb88c7a18da6cf15
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3007
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The xCORE-XA Core Module board has an XS1-XAU8A-10 SoC with 8 xCORE cores
and one ARM core. This config is for the ARM Cortex-M3, via J-Link OB.
Tested with "J-Link OB-STM32F103 V1 compiled Feb 5 2014 13:48:52".
Change-Id: Id7fadf8f323b45d5cfc0cae1054bd7b916771d6a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2763
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The XS1-XAU8A-10 has 8 xCORE cores and one ARM core.
This config represents the ARM Cortex-M3 core, which is apparently
Silicon Labs EFM32 Giant Gecko IP.
Change-Id: I998360f096c759d2e274d96c1ca2e0450ba61146
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2762
Tested-by: jenkins
Reviewed-by: Oleksij Rempel
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Most Xilinx FPGA devices contain an embedded, unique device identifier
called the "Device DNA". The identifier is nonvolatile, permanently
programmed into the FPGA, and is unchangeable providing a great serial
/ tracking number.
Debugging was done in https://github.com/timvideos/HDMI2USB/issues/36
Change-Id: Iad03eafb40887f0321a4dc22858a7c3bf37a12b3
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2960
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Another board supported by the ixo-usb-jtag project.
Change-Id: I676197c64e208886bc03d1bafcc964ef1fc2160b
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2963
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The board is supported via the ixo-usb-jtag firmware.
Change-Id: I1e8a5ead850c0843b8532a5b54a7e7117778278e
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2962
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also add further documentation about the project and how to use it.
Change-Id: Ia9878de566b3c8c1ea29f129287d5aea904d861d
Signed-off-by: Tim 'mithro' Ansell <mithro@mithis.com>
Reviewed-on: http://openocd.zylin.com/2961
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Flash driver "mini51.c" and "nuc1x.c" are same target MCU.
This patch integrates each driver and functions,
and makes into new "NuMicro" flash driver.
Change-Id: Ifff5c1cfdd265acca0f489631695be9194fa144c
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2794
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A target config and a simple flash driver for the ADuCM360 microcontroller.
The EEPROM of the chip may be erased and programmed.
Change-Id: Ic2bc2f91ec5b6f72e3976dbe18071f461fe503b8
Signed-off-by: Ivan Buliev <i.buliev@mikrosistemi.com>
Reviewed-on: http://openocd.zylin.com/2787
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Tested with Porcupine-1 JTAG adapter board and Digilent JTAG-HS3 interface;
reset does not yet work, pending nSRST configuration of the interface used.
Change-Id: I0d0679e098d93ffbd1539004cdb900e2a8ae4a25
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2730
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As found on the Parallella-I board SKU A101020.
Change-Id: Ie7e7a36325926d67fbe555b46a9be8a74fac8dba
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2729
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Derived from tcl/interface/digilent-hs1.cfg.
JTAG-HS3 has an open drain buffer on pin 14 for SRST to work with
PS_SRST_B on Xilinx Zynq SoC.
Change-Id: I1e9e72d0511528a61207e318aff937ae9fad5bf9
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2728
Tested-by: jenkins
Reviewed-by: Robert Jordens <jordens@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for SWD transport similar to sysfsgpio driver.
Added configurable peripheral base address to support Raspberry Pi 2.
Change-Id: If76d45fbe74ce49f1f22af72e5f246e973237e04
Signed-off-by: Christoph Pittracher <pitt@segfault.info>
Reviewed-on: http://openocd.zylin.com/2802
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add the chip IDs corresponding to the new 5V "SAMC" parts which are
otherwise identical to the SAMD and should work with this driver. Also
add the configurations for their Xplained Pro boards.
Change-Id: Ic268d4ac384a3a77d4211a94da9f9faf4d8c0f7b
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2809
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Pipistrello is a low cost FPGA board with a Xilinx
Spartan6 LX45, a SPI flash and onboard FTDI JTAG.
This board is a good example use case for the jtagspi
flash driver talking through a proxy bitstream.
Change-Id: I04a80610ff825c36ebcb67b879507028eed141ad
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2846
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Many FPGA board speak JTAG and have a SPI flash for their bitstream
attached to them. The SPI flash is programmed by first uploading a
proxy bitstream to the FPGA that connects the JTAG interface to the
SPI interface if the IR contains a certain USER instruction. Then the
SPI flash can be erase, written, read directly through the JTAG DR.
The JTAG and SPI signaling is compatible. Such a proxy bitstream only
needs to connect TDO-MISO, TDI-MOSI, TCK-CLK, and the activate the
chip select when the IR contains the special instruction and the JTAG
state machine is in the DR-SHIFT state.
Change-Id: Ibc21d793a83b36fa37e2704966aa5c837c4dd0d2
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/2844
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This covers only the Cortex-A5 for now, not the Cortex-M4.
Change-Id: I739ec52b14b83d6e9f124ed61f8941502e481402
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2766
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
code polishing to be consistent with other scripts
Change-Id: Ib52a92f48df9d2bdf543792b856e33aa04dbebe3
Signed-off-by: Radek Dostal <radek.dostal@streamunlimited.com>
Reviewed-on: http://openocd.zylin.com/2779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reset stopped working with this setting.
Change-Id: I98e8fafa48e0ab65dce8110870be422edf7b2fdb
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2727
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Split TMS570 target into LS31/LS21 and LS20/LS10 targets.
Board for the TMS570LS20SUSB Kit, which uses the TMS570 Cortex-R4 MCU from TI.
Tested attaching.
Change-Id: I1a69ac1ed800d0d6b7f9860c19cbd149e3e47620
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2089
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds support for the new Atmel SAML21 family of low-power Cortex
M0+ devices. Their Flash controller is essentially the SAMDxx one so
the change consists of adding the new part IDs. Unfortunately the
device ID logic had a couple of mistakes in it that did not affect
anything on SAMD2x devices (due to 0 values expected there) but that is
a problem on L21, it's therefore addressed here and things should now
match the datasheets.
Tested on Amtel SAML21 Xplained Pro development kit against the included
SAML21J18A there. Also tested for regressions on a SAMD20 and SAMD21
using their dev kits.
Change-Id: I768f75e064b8656c15148730dacaa4c3acfc4101
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2690
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use mmw to manipulate only selected bits of the word. msb and mwb verify the
memory location and may error on PLLRDY set as a result of PLLON written.
Change-Id: I9a4c1e58f002a1e5e99be1bd34aac27ba65d111d
Reported-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2702
Tested-by: jenkins
GP and EPOS EVMs do not provide xds100v2 on board,
rather they have a pin header which can be used
to attach any debug pod the user might want.
Change-Id: I61678c50900fbe0fab500ea42f85ecde7a490ded
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2618
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a remake of http://openocd.zylin.com/1966
originally written by Angus Gratton <gus@projectgus.com>
ATSAM4L has a "System Manager Access Port" (SMAP) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Without this change any use of sysresetreq or srst locks the chip
in reset state until power is cycled.
A new function smap_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and SMAP reset is released then.
Change-Id: Iad736357b0f551725befa2b9e00f3bc54504f3d8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2604
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Also some hints around deprecated tcl/interface/turtelizer2.cfg added.
Change-Id: Ifa57b49febffaeddd5d8ff0a48833d3544927b10
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2584
Tested-by: jenkins
Reviewed-by: Harald Kipp
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Works best after update to firmware v2.3.
Change-Id: Id2d3a0ae28bba014ee5338df9280fe39773c3398
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2570
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Assembled by trial-and-error for an S6E2CC.
Change-Id: I317c12d24c9075ce3de286455fa3ee45731c5c81
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2569
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Original submitted code had only been tested with em358, but testing with
actual em357 revealed errors that this patch corrects.
Change-Id: I70cf31210de8ed84e3755a56e76261ad200322bb
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2581
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When using ppdev driver 0 is the most appropriate default value as it
corresponds to /dev/parport0. Raw port address is suitable only for
direct access (I think that's parport-giveio on windows).
Reported by danitool on IRC.
Change-Id: I983c22251de6601b433ad31aaf660fb664cee7e9
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2572
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested with "J-Link Lite-XMC4000 Rev.1 compiled Dec 7 2012 19:23:07"
on XMC4500 Relax Lite Kit V1.
Change-Id: Ib680a444fa4cadbf640afba15d607c0e6bd4ab2c
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2567
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Base config, verified against XMC4500, XMC4400 and XMC4100/XMC4200 manuals.
Change-Id: I10907bdf307bc6d11dc5454bf5391758de49dc30
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2480
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this is just to avoid open coding that in
icepick_d_tapenable. Cleanup only, no functional
changes.
Change-Id: Iabd20291b7bdd95957afa1c74f52171789201227
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2624
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
it also works on icepick_d.
Change-Id: I50c0c81286aae673c94ea77e47454ff48eab1668
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2623
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reusing what's already there to ease maintainability.
Change-Id: I2030581669c644e2d9d9f9968075ab6344445d04
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2622
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This commit is only for the sake of completeness as
default coreid is zero. In any case, coreids 1-4 are
used for the different PRU cores inside the SoC.
Change-Id: I775f2f444b1a908ffaf7bdbc43bcc966f19668c4
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2621
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use more descriptive names for JRC and DAPs
so they more closely match documentation.
For example there's no Cortex A9 DAP, that's
the DebugSS DAP where Cortex A9 target sits. In
that same DAP we have have ETM, STM and both
dual-PRU subsystems.
Change-Id: I0e66ebb6299763f96606fae3e4c62e5785c804f2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2620
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Main DAP (where Cortex A9 sits) ID is actually
0x46b6902f. Fix it.
Change-Id: Ifa3335186bcf60d264d4ecea477bfe2f5ca10ead
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2619
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add support for Texas Instruments AM437x
Industrial Development Kit support.
Change-Id: I33ed71c7392c3805a86cf2c8adce83c0e8aa323d
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2617
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
this event handler will configure and lock PLLs
and configure DDR so platform is placed in usable
state.
Change-Id: Idd02f4c9789181d69578f8606ac3576ea1dd8a0b
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2616
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
sometimes, watchdog might be left running and
it could expire in the middle of a debug session,
to prevent that, just make sure to disable watchdog
on reset-end if current state is 'halted'.
Change-Id: Ib4f2a2321cba17cd8c56ca3ae63114a563a6de90
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2615
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
a later commit will implement a proper reset-init
handler to lock pll and configure ddr as we should.
Change-Id: I432cf28a5a944bfa83c20aed7298dbd29df30e38
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2614
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
xds100v2 asks us to call these three commands to
guarantee proper behavior, so do it.
Change-Id: Iecf9c148ce7c2082ef915b46eeb511ceea395cc3
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2613
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
default already is jtag, but this silences a
warning during startup.
Change-Id: I94478327bbb259649500ef74a5b5c10d51e2a517
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2612
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
According to AM4379 TRM [1], table 2-1 L3 Memory Map,
we have a total of 256KiB and there's no reason not to
use it all.
[1] http://www.ti.com/lit/ug/spruhl7b/spruhl7b.pdf
Change-Id: I117f2afe721bc4e3f0df304d3542e1a91aa69d12
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2611
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since commit ec9ccaa288 (arm_adi_v5: make dap_lookup_cs_component()
traverse subtables and handle multicore) AM437x devices can't be used
with OpenOCD anymore. The reason is that dbgbase used to be set to zero
before that commit and that just happens to work with AM437x devices.
A more robust solution is to pass correct dbgbase when creating the
target, which this commit does.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change-Id: Iaf2617804324de8094b25137943e08b84f14c75f
Reviewed-on: http://openocd.zylin.com/2602
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This should allow most of the existing configurations for older
versions to remain compatible without forcing the user to change his
or her config to explicitly select transport.
Also in some circumstances can remove the need to chain a "-c transport
select X" when building custom configs on the command line, which seems
like a common new user pitfall.
Change-Id: Ic87a38c0b9b88e88fb6d106385efce2f39381d3d
Suggested-by: Petteri Aimonen <jpa@git.mail.kapsi.fi>
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2551
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Valgrind-tested.
Comparison of flashing performance on an FRDM-KL25Z board running mbed
CMSIS-DAP variant, 5MHz clock, old driver:
wrote 28096 bytes from file demo.elf in 26.833590s (1.023 KiB/s)
verified 27264 bytes in 1.754972s (15.171 KiB/s)
this implementation:
wrote 28096 bytes from file demo.elf in 3.691939s (7.432 KiB/s)
verified 27264 bytes in 0.598987s (44.450 KiB/s)
Also tested "Keil ULINK-ME CMSIS-DAP" with an STM32F100 target, 5MHz
clock, results reading from flash, old driver:
dumped 131072 bytes in 98.445305s (1.300 KiB/s)
this implementation:
dumped 131072 bytes in 8.242686s (15.529 KiB/s)
Change-Id: Ic64d3124b1d6cd9dd1016445bb627c71e189ae95
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2356
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since the very first flash bank is already defined in target/kx.cfg,
there's no sense in repeating it.
Reported and tested by Richard Braun.
Change-Id: I417b7072b5e6675ddbf824446e7581b8b7da8f4b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2595
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This provides support for various trace-related subsystems in a
generic and expandable way.
Change-Id: I3a27fa7b8cfb111753088bb8c3d760dd12d1395f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2538
Tested-by: jenkins
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I984d2018f7d47a1042f1e12894563154fa7b566c
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2196
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The signal names are changed for consistency with TI's docs and
sources.
Change-Id: Ic5c5314daa20f6f610be8a848399f951d47aa137
Signed-off-by: Matthijs van Duin <matthijs@rinnic-vaude.nl>
Reviewed-on: http://openocd.zylin.com/2231
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Initial Support for AT91SAM7A2 on Olimex SAM7-LA2 board.
The board seems not to be able to reset into halted mode, as srst is
connected to NRESET of the cpu (configured srst_pulls_trst).
JTAG RCLK is connected to CLK.
Tested with interface/ftdi/olimex-arm-usb-ocd-h.cfg.
Change-Id: I2bdd67e3683e45f1119c5850bad294aa107891d8
Signed-off-by: Arne Wichmann <arne.wichmann@gmail.com>
Reviewed-on: http://openocd.zylin.com/2318
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The F334 disco board has a stlink V.2-1 as F3 nucleo boards. Normal F3 disco
boards use stlink v2 and can't ne used.
Change-Id: I77ebef93b184592f25ff18bb2da776d636f60ff0
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2434
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds configs for Alphascale asm9260t ARM based SoC and
Evaluation Kit based on this chip.
Change-Id: Id8d3a1ef204e3ae84540c2693e3d62650ba82f73
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2515
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The flash definition belongs in the target cfg. Add some working area
and suitable reset_config.
Make kx.cfg more similar to klx.cfg.
Disable rclk as it is dead slow and a fixed 1MHz clock seems to work.
Change-Id: I8328f179c3a33be64403da93616abb48651bdfe6
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2227
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Configure the LED to be off by default, blink on activity.
Change-Id: I8515ee66c49bddf866268b85811be15c2dbc086c
Signed-off-by: Anton Kuzmin <anton.kuzmin@cs.fau.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2539
Tested-by: jenkins
This is a new driver for Silicon Laboratories SiM3 microcontroller
family, based on the work of Ladislav Bábel. The driver will try to
detect the type of MCU from the device id register, and if this
fails it will use the flash size from the flash bank command.
Driver added to the documentation and to the README.
TCL script added.
Tests:
* Hardware: SiM3C166 (pre-production) and SiM3U167
* Binary: 4kb, 197kb, 256kb
* Flash protect not tested
Change-Id: I701e0cf505ca8ad99be7f83543fe5055b2f65dcc
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2078
Tested-by: jenkins
Add serial option to jlink config commands, handy when there is more than one
adapter connected.
To select adapter 0123456 for OpenOCD, use
jlink serial 0123456
Change-Id: Ib29ce3f0c4975e1169211721a4531bf4db61f1ee
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/2521
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the board to the list of supported devices for the easy
recovery procedure. Only ram_boot is supported for this target.
Change-Id: I144e1836f8b6257e96a42c98c2668da74ce243f6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2520
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Add configs for Atheros ar9331 MIPS based WiSoC and
board based on this chip: TP-LINK TL-MR3020
Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2519
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
adds flash support for Nuvoton M052, M054, M058, M0516 microcontrollers
into the mini51 driver, patch also adds support for programing LDROM,
flash data and flash config.
I've tested it on a M0516LBN microcontroller using an ST-LINK/V2:
1. removing security lock:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "init ; halt ; mini51 chip_erase; exit"
2. flashing:
openocd -f interface/stlink-v2.cfg -f target/m051.cfg -c "program file.hex"
Change-Id: I918bfbb42461279c216fb9c22272d77501a2f202
Signed-off-by: Pawel Si <stawel+openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2426
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Added support for the Cortex-M3 based TI low power RF SoC CC2538 and
the CC26xx family.
These chips need a start sequence for switching from cJTAG to JTAG
before being used with OpenOCD, this is done in the tcl proc
ti_cjtag_to_4pin_jtag in the ti-cjtag.cfg config.
The configs for CC2538 and CC26xx run the start sequence on post-reset
event and set the ICEPick IDCODE in the data register for OpenOCD to
read, this is done so that every time OpenOCD resets the device, it
will enable JTAG.
Change-Id: I7db620211c0e7e03fad59d24fe31d23a9cdcfedc
Signed-off-by: Jacob Palsson <jaaacke@gmail.com>
Reviewed-on: http://openocd.zylin.com/2232
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds support for Silicon Labs (formerly Ember) EM357
and EM358 chips and derivatives.
Change-Id: Ie63aed95a2f4ef1a6b955e301a51b4de1b3a5462
Signed-off-by: Ed Beroset <beroset@ieee.org>
Reviewed-on: http://openocd.zylin.com/2470
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
New NOR flash driver was derived from stm32lx.
Procedure ocd_process_reset_inner is overriden in psoc4.cfg
to handle reset halt and system ROM peculiarities.
Change-Id: Ib835324412d106ad749e1351a8e18e6be34ca500
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2282
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds a trivial config for LPC8xx chips based on the already
existing infrastructure in lpc1xxx.cfg.
Change-Id: I7384df1f3c2e3e8ab767319728db5c4f8149480f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2464
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Added support for the ST nucleo l152re board with a stm32l152ret6 MCU,
analog to st_nucleo_f* configurations.
Change-Id: Id2c61dc7a7cb2e1cc64442191b367bab4247bdeb
Signed-off-by: Thomas Eichinger <eicht@lepus.uberspace.de>
Reviewed-on: http://openocd.zylin.com/2489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It depends on the particular target whether it can work with SRST
asserted or not, so this belongs to the target config rather than the
board config.
Also, this allows for simple
openocd -f myboard.cfg -c "reset_config connect_assert_srst"
command to be used whenever a user feels a need to connect to an
unresponsive target.
Change-Id: I3d8da9ae47088fc0c75a20bfdd20074be1014de0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2459
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
So remove it from all the configs, it's misleading, and leads to cargo
culting of config files.
Change-Id: I2b77e60d5e96f9759c7c9fc91b20e73be2e95d9a
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2446
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is an integrated adapter used on the IoT-LAB boards.
Schematics are available from
https://github.com/iot-lab/iot-lab/wiki/Docs/openm3-schematics.pdf
Change-Id: I1c80e72653c3f319bb04d01e3dfddb1c2447c398
Tested-by: Quentin Lampin <quentin.lampin@orange.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2415
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It is derived from ti_tmdx570ls31usb.cfg, using a different TAP ID.
Change-Id: I2d911995c76ea4f75a780cc230d61f4959825809
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2440
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should have been corrected earlier with the split of l1/l0 code
apart.
Change-Id: I87b94a310ae7e76318554a9cd2705348a942d58b
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2447
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
commit b5a6ba46 broke the following board files, update to new cfg.
Change-Id: Ic3b776bd32eb72eae6ad1e130e329268ce9ba71a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2384
Tested-by: jenkins
L0 is cortex m0+, so different id codes, SWD only, different addresses
for the clock speedup. It has no endian options, no boundary scan.
Removed all L0 specific portions from L1 files, and renamed files to clarify
their purpose. The deprecated stm32lx_stlink.cfg is kept as is, as it is only
around for backwards compatibility with prior releases.
Tested on STM32L053 Discovery and STM32L151 Discovery.
Has _not_ been tested with jtag on L1.
Change-Id: I8eea890d2f92a302d9e9c8a8832d218ee1b6bcfc
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Juha Niskanen <juha.niskanen@haltian.com>
Fix script parse error, when using JTAG, introduced in
commit 0187ced9ed
Add several BS TAPIDs with comments about ST documentation.
Change-Id: I8d0370b244ccaf7ea0dbe1919bfad1915f7317d4
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reviewed-on: http://openocd.zylin.com/2376
Tested-by: jenkins
Reviewed-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Since all F4 parts have an internal HSI providing 16MHz, it's safe to
use 2MHz JTAG frequency by default.
Change-Id: I2702d5a1d642d4acd4af2db54c028949132c6900
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2383
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this board use STLink-V2-1, the STM32L1xx use the STLink-V2.
Change-Id: Ie58f45affcb1e9a6fed711b48c3c03b5035ab2b2
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2317
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add CPUTAPID for stm32 L0xx mcu devices. Using -expected-id to
add the new id with the id for L1xx devices. This for reduce the
duplicated code.
Change-Id: I48bd230884ecf38fa200c620b547bdf3b5f59132
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2315
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
According to my inspection of an Olimex ARM-USB-OCD-H adapter ACBUS0
is connected directly to an SN74LVC2T45 buffer input B2, and the
corresponding output A2 is connected directly to the JTAG
connector. It seems the information in the Olimex flyer is incorrect
for the -H version and TRST can't be tri-stated, ACBUS2 is unused.
The older ARM-USB-OCD device has SN74AC244 for an output buffer and
ACBUS2 controls its !2OE, ACBUS0 connected to 2A1 (2Y1 is nTRST), in
accordance with the information flyer.
Change-Id: I22828b7b959b6f62c3f51367feb8fab9705641e5
Reported-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2286
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tim Sander <tim@krieglstein.org>
Remove this underutilized feature. Despite the fact that a lot of configs
specifies a arbitrary "variant", only the xscale target actually defines
any.
In the case of xscale, the use of -variant is dubious since
1) it's used as a redundant irlen specifier,
2) it carries a comment that it doesn't really need it and
3) only two xscale configs even specify it.
If there's a future target that needs a variant set, a target specific
option could be added when needed.
Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2283
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The hla_serial command allows for a programming device serial number to be
specified in addition to USB VID/PID. This allows for multiple ST-LINK/V2
programmers to be attached to a single machine and operated using openocd.
Change-Id: I350654bf676eb26ba3a90450acfa55d2a5d2d791
Signed-off-by: Austin Phillips <austin_phillips@hotmail.com>
Reviewed-on: http://openocd.zylin.com/2198
Tested-by: jenkins
Reviewed-by: Martin Glunz <mg@wunderkis.de>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This combination is known to work properly with 2MHz JTAG clock.
Change-Id: Ie5ec3d3b415efbb13faee7d34e0c7f862b78350c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2266
Tested-by: jenkins
Without this SheevaPlug debugging interface can't be matched.
Change-Id: Ifca149130d03c1aa165ed1123e8540e49485f023
Reported-by: Andreas Schneider <schneider.andi@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2265
Tested-by: jenkins
Since now auto-detection for flash size works nicely, there's no
reason to keep numerous configs around.
Change-Id: If0cbc37985abf17ef7c1f7d0688e76500fac228f
Signed-off-by: Vanya Sergeev <vsergeev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1960
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds config to allow JTAG debugging of an ARM core of a modern
hybrid SoC by Research Centre "Module"
(http://www.module.ru/en/company/). К1879ХБ1Я is targetted at set-top
boxes and other multimedia equipment, the official SDK is Linux-based.
Change-Id: Ib2ae5784d25699f952682e66b025a3f677a76d5d
Signed-off-by: Бурага Александр <dtp-avb@yandex.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2272
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the research by Eldar, TINY-H adapter has nTRST connected
to ACBUS0 directly via a 100 Ohms series resistor. I think it's safe
to assume the older TINY adapter does the same.
See high-res photos at [1].
This patch should fix issues with JTAG for the case when nTRST is
actually connected but is missing from the config.
[1] https://wikidevi.com/wiki/Olimex_ARM-USB-TINY-H
Change-Id: Iaaee7be30536ebb502802d38b82cd9573408f854
Reported-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2247
Tested-by: jenkins
Reviewed-by: demokmail <demokmail@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is for mx6q TO1.1.
Change-Id: Id6af2ed232fc19be9bf49eb6d2df0004c6668698
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2253
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
When you source a JTAG-SWD converter config, any other transport
doesn't make any sense, so just autoselect it right there.
Change-Id: I6c098740905a0d4007473fc19cc07e11cbcc9369
Suggested-by: Хайруллин Эльдар <eldar.khayrullin@mail.ru>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2248
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Eldar Khayrullin <eldar.khayrullin@mail.ru>
According to Nordic Semiconductor Product Anomaly Notice (document
NRF51822-PAN), item 16, some revisions of nRF51822 sometimes reset
without all RAM blocks enabled. This was noted on NRF51822-QFAA rev
CA/C0, only 8KiB of memory was accessible.
This patch turns on all RAM following a debugger induced reset
(matches specified behaviour.)
Change-Id: I4f8be4ec3d1271da7fe5bc9a084fdcb2968535bb
Signed-off-by: Angus Gratton <gus@projectgus.com>
Reviewed-on: http://openocd.zylin.com/2202
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should allow to share common configs for both regular access and
high-level adapters.
Use the newly-added functionality in stlink and icdi drivers, amend
the configs accordingly.
Runtime-tested with a TI tm4c123g board.
Change-Id: Ibb88266a4ca25f06f6c073e916c963f017447bad
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[gus@projectgus.com: context-specific deprecation warnings]
Signed-off-by: Angus Gratton <gus@projectgus.com>
[andrew.smirnov@gmail.com: additional nrf51.cfg mods]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1664
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The Atmel SAMR21 is a Atmel SAMD21 with an Atmel RF233 in one package (two
dies). Tested with the SAMR21 Xplained Pro eval kit.
Change-Id: I1d79ea05834b925d7ec810527206fe86854e684b
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2194
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Resistor hack is runtime-tested, other configs are based on
schematics.
Change-Id: I8daffa0434cd41d142fbec7c230a302284f7aa31
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2184
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Use a special signal instead of a dedicated swd mask. Amend
jtag-lock-pick_tiny_2 config accordingly.
Change-Id: Ifb007a0b5434b590c52f936efd5f5458e913e2e4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2183
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
I looked through all the target configs after stripping comments and
such from them with sed to see what jtag-specific commands can appear
first, and it looks like all the meaningful combinations should be
covered.
Change-Id: I8d543407b7f4ac8aca7354ecd50e841c8a04d5f3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2179
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
SAM4L requires additional steps to be taken right after SYSRESETREQ is
issued in order to function robustly:
- CMSIS-DAP DAP driver needs to explicitly check for sticky bit
errors since it is possible for adapter to perform successful
write opration, report no errors and then, under the hood, do
some other things that will result in sticky bit being set.
- Debugger needs to wait for security system to finish
intialization and assert CDBGPWRUPACK before proceeding
This change is related to commit http://openocd.zylin.com/#/c/1995/
Change-Id: I741c95a809bfd60d930cec9482239e4796a62326
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2088
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
fm3 flash driver needs to know which chip variant is used.
This fixes "unknown fm3 variant: mb9bf500.cpu" error if the config is
used as is.
Change-Id: I500fcfb413f23ee246678cec5bd19d14139a28e2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2160
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This isn't needed nor a recommended practice now, was a simple
copy/paste from amdm37x.cfg anyhow.
Change-Id: I064226dc859d7563cfad945b577279fc37448645
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2068
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Maximum frequency wasn't tested on hardware but the docs seem to be
quite explicit and do not mention any restrictions for that.
Change-Id: Idcf58df5358d06525e683f07c76eedad8f0b292d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2120
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds Micrel's KS869x target. The configuration was taken from
http://www.mmnt.net/db/0/0/www.micrel.com/ethernet/8695 - Micrel's
FTP server i.e. their OpenOCD 7.0 package.
The only change compared to the original file is the removal of
reset configuration, as it belongs to the board configuration.
Change-Id: Ic8509aa5fe5ce3166a3129e1c055280a3b2b9312
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-on: http://openocd.zylin.com/2125
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b
Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add configuration file for General Plus GP326XXXA series. Tested on
GP326833A on GPC-1737B board.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: I1ad0e22598b01317bbc823870a7a262e9192c595
Reviewed-on: http://openocd.zylin.com/2058
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The Gumstix AeroCore board [1] contains a STM32F427 microcontroller.
Schematics for this board will also be made available [2].
The JTAG interface for this chip can be accessed via a USB connection
provided by an FTDI chip (0403:6011).
[1] https://store.gumstix.com/index.php/products/585/
[2] https://pubs.gumstix.com/boards/AEROCORE
Change-Id: I0bf3bb525f51528bedd807b1f7210b09ef2e1015
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Reviewed-on: http://openocd.zylin.com/2117
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74
Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Also add the board to the firmware recovery script.
Change-Id: I4f9c895dae171df7249e3b1c0563b288518b9fe0
Signed-off-by: Lee Bowyer <lee@sodnpoo.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
SoftDevice stack ihex binary, provided by Nordic expects being able to
write data necessary for its correct operation at the adresses inside UICR.
This patch exposes UICR region of flash as a second bank on the MCU to
facilitate that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Change-Id: Idbc140b8de027f60655f78043877b7c054eb06f9
Reviewed-on: http://openocd.zylin.com/2013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch allows users to specify TAP_TYPE from
the command line when using or1k_generic.cfg.
Change-Id: I9f4b7d8e4867658fa34bb4e92fc3a5f25227df11
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/2056
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds support for the am43xx SoC and the AM437x GP EVM and AM438x
ePOS EVM.
Change-Id: I09cbb09072f38e0e08fdd520dedb6e67d45056be
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2047
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
instead of replicating icepick_d_tapenable in many of TI's newer
platforms, we can move to icepick.cfg and just call it from board TCL
configuration file. This is similar to the C but has a few changes we
need to make.
Change-Id: I0ab48005ccd66cd5b67b919fb5e3b462288f211d
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2030
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested on ZedBoard by Tim Sander.
Change-Id: I4316d9b4d36f01bbe91a46c78ea8bca22efb1a5a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2029
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
From testing this target does not seem to support using SYSRESETREQ, change
the default to the safe VECTRESET.
This target also has other reset issues (srst not working) that will be
addressed in another patch.
Change-Id: Icfc78347dc71aa3a062ddea63190a818d7fbc760
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1995
Tested-by: jenkins
Reviewed-by: Angus Gratton <gus@projectgus.com>
Atmel's SAM3 and SAM4 processor families are very close to each other
in many respects. However, so far, only the SAM4 target script
contained the magic to allow using SWD, while SAM3 was tied to JTAG
only. This e.g. prevented the CMSIS-DAP driver from accessing SAM3
devices as it only uses SWD transport (by now).
The patch pulls all the things from the SAM4 target script that are
also applicable to SAM3 devices. With the patch, an Atmel CMSIS-DAP
debugger (Atmel-ICE) was proven to be able to successfully attach to a
SAM3S-EK evaluation kit. I also cross-checked that accessing through
a SAM-ICE (Segger J-Link) still works with the patch.
Change-Id: I20dafbff8e1e9f967da950e48a56205586eeef8d
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Reviewed-on: http://openocd.zylin.com/2046
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reported and tested by Gracana on IRC.
Change-Id: If0524d2d627d566e8b5e1d00784dd7556f44b125
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2036
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The new version of STLink (V2-1) has a different USB endpoint layout.
As the PID of the device also changed it's possible to change EPs used
by OpenOCD in runtime. The patch adds three new fields to stlink_usb_handle_s
and assigns right EP numbers in stlink_usb_open().
Parts of the code inspired by and used with consent of Jens Hoffmann.
Change-Id: I93b69fb889f15317e9bf864905f435905db39745
Signed-off-by: Bartosz Bielawski <bartosz.bielawski@gmail.com>
Reviewed-on: http://openocd.zylin.com/2019
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for Broadcom's dual A9 mobile SoC and its reference board.
Change-Id: Ia145b120043bddc89c44726066023154ae390788
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-on: http://openocd.zylin.com/1926
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The XDS100v2 is often embedded in a number of platforms using the
VID/PID of 0x0403/0x6010 and a generic FTDI device description. Add
this VID/PID combination and remove the description line.
Change-Id: I370e6199ac24f802426e9541e19ee38f18f1209a
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2016
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
flash: at91sam4: add support for the SAMG53 family (this also covers the
SAMG51). The SAMG5x parts have an EEFC (enhanced embedded flash controller)
which seems to be identical to the EFC that the sam4 driver supports.
Add a script for the Xplained Pro G53 board, this has the onboard CMSIS-DAP
debugger and a SAMG53N19. Tested on this board and chip combination.
Change-Id: I12af50402cd2069b3c7380d92e6fe54816d6c045
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1974
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Intel Quark X10xx SoC debug support added
Lakemont version 1 (LMT1) is the x86 core in Quark X10xx SoC
Generic x86 32-bit code is in x86_32_common.c/h
Change-Id: If2bf77275cd0277a82558cd9895b4c66155cf368
Signed-off-by: adrian.burns@intel.com
Reviewed-on: http://openocd.zylin.com/1829
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adapter is special and needs a reset sequence to be performed
before operation. Since there're no suitable hooks to do that, we have
no choice but to ask the user to manually add the necessary commands
to his or her config file.
Change-Id: I48fb4276e77529768266840221b68c3ae26801e1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1884
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
TUMPA Lite is a cheap FT232H-based breakout board, without any
buffering. It also lacks series resistors so for some targets
(especially when not using ridiculously short wires) one needs to add
about 47 Ohms in series on every high-speed line.
The SRST line is connected directly to the FT232H too.
Real-life tested (including SRST and TRST).
Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1918
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Originally the LPC17xx user guide (UM10360 Rev 2) stated that SYSRESETREQ
was not supported, so this was the default cortex_m reset mode.
Rev 3 of the same user guide states that it is now supported.
This has been verified on a LPC1768 mbed platform, previously I have not
tested this functionality.
Change-Id: I4858248903981a1c93ce75016e67c9e02702fcc5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1892
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patchs adds a new access driver for the existing
USB-Blaster interface driver.
This interface (as it is build-in on the sockit development
board) is composed of a Cypress EZ-USB plus a CPLD.
The Cypress chip as an embedded 8051 microcontroller.
When it's powered up, the firmware is downloaded to the
chip then the device is disconnected and reconnected with
the new firmware.
The USB-Blaster II protocol is almost identicial to
the old one. The only difference is that you need to
send a 0x5F before read TDO back. This command
seems to copy TDO buffer datas to the endpoint buffer.
Driver will be auto enabled if libusb-1.0 is detected.
Change-Id: I562a720a68cb4dcabeab791947d5d38776cb70fa
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1791
Tested-by: jenkins
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested with SAMD21J18A on the SAMD21 Xplained Pro board.
Change-Id: Ice9ebcd229ed038b3193baf92d910f9256d7ce91
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1873
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a new NOR Flash driver, "at91samd", which supports the
built-in Flash on Atmel's D-series Cortex M MCUs, starting with the D20.
Parts and their geometry are detected automatically using the DSU and
lookup schemes described in the D20 document, 42129F–SAM–10/2013.
Future D-series variants and families should presumably use this
controller as well (possibly with minor changes and improvements).
Tested on the SAMD20 Xplained Pro board, for which we also add the
corresponding Flash configuration.
Change-Id: Id8d3dd601e9f53121682d1a1190d0be4ea3b83eb
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1684
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds a new NOR Flash driver, "at91sam4l", which supports the
built-in Flash on Atmel's low-power SAM4L family of Cortex M4 MCUs.
Parts and their geometry are detected automatically using the Chip ID
and lookup schemes described in document 42023E–SAM–07/2013.
Tested on AT91SAM4LC4CA via the SAM4L XPlained Pro development kit.
Change-Id: If73499dee92cc8ce231845244ea25c6984f6cecd
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1639
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These kits feature a CMSIS-DAP compliant debugger and so have been added
as part of the pending support.
Currently the flash drivers for the L8 and D20 are wip.
One issue this implementation of CMSIS-DAP raised is that it supports
512byte HID reports, however using the current HIDAPI we have no cross platform
way of querying this info. Long term we plan to add this support to HIDAPI.
Change-Id: Ie8b7c871f58a099d963cd71a9f8a0105a38784e9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1625
Tested-by: jenkins
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
This adds a set of helper functions with the aim to make it possible
to flash mass-market devices without RTFMing altogether (i.e. to
obsolete GPL-violating proprietary tjtag and other similar software).
Real-life tested on an RT-N16 and WRT54GL.
Change-Id: I197a9b28a5f386803f081057c4b4ebf2f9c447b1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1850
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested flashing a real v1.1 device.
Change-Id: Ie0d202b9fded8b92e731d93e0ef17be415a75fc8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1852
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".
The RAM setup is not done as it would require considerable efforts
without much practical gain.
The only issue I noticed so far is that "reset" doesn't actually reset
the chip.
Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.
Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.
Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* openocd.berlios.de -> openocd.sourceforge.net
* Update link to AM/DM37x Technical Reference Manual (ver R)
* "ICEpick" is properly spelled "ICEPick" according to TI
Change-Id: Ie04458e82c97ef766ec03bd9b9f27edadf5d1cb2
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1856
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The set command was missing the $ prefix on the SJC_TAPID variable
and so would fail if SJC_TAPID was set
Change-Id: Ib9af58f5188bd8a2bc3f888309f203d624476c27
Signed-off-by: Alex Murray <alex.murray@cohdawireless.com>
Reviewed-on: http://openocd.zylin.com/1811
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on Nemuisan Tokusei's. Untested, but original config was reported
to work ok.
Change-Id: Ic991dce55bfca266880081fe2bbd9e6e263b0fc0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1803
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
all other at91 cfg files already has this fix.
It also fix "No flash at address 0x...." error when JTAG chain consist of
more than one at91sam7sx cores during attempt to flash other than first mcu
in chain.
Change-Id: I7785d9103d0fc494b6a823e2c73f850373ffe112
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1812
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32F42xxx & STM32F43xxx series boudary scan TAP-ID are differ from
STM32F405xx/07xx & STM32F415xx/17xx.
And Section number was also fixed for RM0090 rev5.
Tested on a STM32F427IIT6 and STM32F429ZIT6.
Change-Id: Ie9c54c55b97b9c396ace752d94ea2ad916cc8479
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1808
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a Cortex-M1 controller targetting aviation appliances.
Contributed (and live-tested) by 8daemon.
Change-Id: I133d6122cf6492b51ddbdbd800c16ba121d51bf3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1818
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Working against openmoko gta02 target, including TRST and SRST (the
stupid samsung chip fully resets under trst, so it's actually of
little use here).
Change-Id: I831124659fc12efbccef536f07d15509c2112f92
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1814
Tested-by: jenkins
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This add support to the Xilinx BSCAN_* virtual JTAG interface.
This is the Xilinx equivalent of the Altera sld_virtual_jtag interface,
it allows a user to connect to the debug unit through the main
FPGA JTAG connection.
Change-Id: Ia438e910650cff9cbc8f810b719fc1d5de5a8188
Signed-off-by: Sergio Chico <sergio.chico@gmail.com>
Reviewed-on: http://openocd.zylin.com/1806
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the TMS570 Cortex-R4 MCU from TI and their USB stick
development kit, TMDX570LS31USB. Tested attaching, reset/halt/run, and
reading and writing memory and registers.
Change-Id: I12d779cef0c2b834f9bcf722307f35677cc4bd8f
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1788
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The schematics used for writing the config file were incorrect, real
hardware needs ACBUS3 _low_ as it's connected directly to the output
buffer's !OE pin.
Also apparently sometimes TUMPA comes with default FTDI IDs.
Real-life tested (including TRST and SRST) with a custom stm32f103
board, thanks to Mike Wang for the adapter sample.
Change-Id: Iab566e6d14f8392030f6ff2c8d976e1b57cf5ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a tcl implementation of public domain tests by Michael Barr,
http://www.barrgroup.com/Embedded-Systems/How-To/Memory-Test-Suite-C
The initial porting is done by Shane Volpe and posted to the mailing
list:
http://www.mail-archive.com/openocd-development@lists.berlios.de/msg16676.html
This patch includes some cosmetic amendments plus hardcodes 32bit word
size (as the code depends on memread32/memwrite32 anyway) which fixes
original code's issue of testing only the first quarter of the
specified nBytes.
Change-Id: I5f3a66f1f16fc4082c7a5a6aba338430646ed21c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1455
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Some boards might have RCLK omitted from the JTAG connector and if the
interface claims support for it, OpenOCD will end up trying to use
RCLK while it's actually impossible.
This is a "cd tcl/target; sed -i s/jtag_rclk/adapter_khz/g *" patch.
Change-Id: Iee7337107bc1457966b104389ba9db75a9c860b4
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1695
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Initial support for using the jtag interface to the Marvell Armada 370
family of SoCs.
Change-Id: Id823a567e8805ac622c3c330bc111297c1dae37e
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-on: http://openocd.zylin.com/1690
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Almost the same as the LM4F120 LaunchPad but the chip is using the new
naming scheme (Tiva C series), supports USB OTG and has some new PWM
hardware blocks.
Change-Id: I6a7b2df76768766471f366cddaf64df3cc63f5f2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1647
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds a driver for the jtag_vpi server [1]. This server is
now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC).
The jtag_vpi server provides an interface between OpenOCD and a simulated
core.
[1] http://github.com/fjullien/jtag_vpi
Change-Id: I717b72cace4845f66c878581345074f99002e21a
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The smallest available RAM size for this family is 2K, set this as the
default. Issue reported by quitte on IRC.
Change-Id: I3318f7f268f7681ffe2cddab61820f4b94c4e5fd
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1559
Tested-by: jenkins
Added new configuration file for gw16042 device.
Also added this to interface/ftdi examples in documentation.
Change-Id: I07bb10bfc79a5d13007288cd57f254d889075214
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Reviewed-on: http://openocd.zylin.com/1563
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The end users on IRC report that actual USB device has different
information in its descriptor so it doesn't match. Remove it
altogether.
Change-Id: Id7841667390a514581e630e67b9283675803135b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1548
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This commit adds two tcl configuration files, one for the Altera
Cyclone V SoC series, and one for the SoCkit development board.
The board configuration is able to halt and resume the cpu cores,
and dump register contents etc. It has not been fully tested, however.
Change-Id: Id3f18c3408975cf986a5f5aec410b5b13240c35e
Signed-off-by: Brad Riensche <brad.riensche@gmail.com>
Reviewed-on: http://openocd.zylin.com/1494
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds example config and flash driver for russian Cortex-M3
microcontroller model.
Run-time tested on MDR32F9Q2I evaluation board; the flash driver
should be compatible with MDR32F2x (Cortex-M0) too but I lack hardware
to test.
There're no status bits at all, the datasheets specifies some delays
for flash operations instead. All being in <100us range, they're hard
to violate with JTAG, I hope. There're also no flash identification
registers so the flash size and type has to be hardcoded into the
config.
The flashing is considerably complicated because the flash is split
into pages, and each page consists of 4 interleaved non-consecutive
"sectors" (on MDR32F9 only, MDR32F2 is single-sectored), so the
fastest way is to latch the page and sector address and then write
only the part that should go into the current page and current sector.
Performance testing results with adapter_khz 1000 and the chip running
on its default HSI 8MHz oscillator:
When working area is specified, a target helper algorithm is used:
wrote 131072 bytes from file testfile.bin in 3.698427s (34.609 KiB/s)
This can theoretically be sped up by ~1.4 times if the helper
algorithm is fed some kind of "loader instructions stream" to allow
sector-by-sector writing.
Pure JTAG implementation (when target memory area is not available)
flashes all the 128k memory in 49.5s.
Flashing "info" memory region is also implemented, but due to the
overlapping memory addresses (resulting in incorrect memory map
calculations for GDB) it can't be used at the same time, so OpenOCD
needs to be started this way: -c "set IMEMORY true" -f
target/mdr32f9q2i.cfg
It also can't be read/verified because it's not memory-mapped anywhere
ever, and OpenOCD NOR framework doesn't really allow to provide a
custom handler that would be used when verifying.
Change-Id: I80c0632da686d49856fdbf9e05d908846dd44316
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1532
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Austriancoder on IRC reports getting this ID on his board.
Change-Id: Ie859f0ee422e18fdb94bf817cdd2b41d15b968da
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1533
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for DENX M53EVK board and it's integrated on-board
JTAG adapter using FT2232H.
Change-Id: I022dcafa7799bb84a7873ba67ed82f1e49094320
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1461
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Pull the jtag_rtck setting from imx51.cfg and imx53.cfg . Since
not all boards using these CPUs do support RTCK signal, move the
configuration of RTCK into board files.
Change-Id: I632c5d38e00ada8779a451cd26428fd122452001
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/1460
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It pointed to the Flyswatter 1 page.
Change-Id: Ib7e82669a31cad2bf8f6ba4a60b25ef9920b2584
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1478
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Ignore version of Boundary Scan TAP in newer revisions of the str9.
Change-Id: I6e205f8c731f07078c469e686025857c180f3a6d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1436
Tested-by: jenkins
Add a config file for TIAO USB Multi-Protocol Adapter.
Based on schematics from http://www.mediafire.com/?zv158nnx1gv0cy2
Cc: Volkan K <volkan-k@users.sourceforge.net>
Change-Id: I0dfd93b0b1e558e4ccd7c94c005c099947ec94df
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1438
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This adds support for JTAG programming by bitbanging GPIOs exposed on
the RaspberryPi's expansion header.
Tested by connecting directly to an STM32VLDiscovery board, without any
additional circuity. I observed maximum about 4MHz on the TCK pin with an
old analogue 'scope and about 100kHz when setting the speed to 100kHz.
Busyloop waiting is needed because even with a single 0ns nanosleep call
(with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low
to be useful.
The speed testing with adapter_khz 2000 gave the following results:
sudo chrt -f 1 nice -n -19 ./src/openocd \
-f interface/raspberrypi-native.cfg \
-c "set WORKAREASIZE 0x2000" \
-f target/stm32f1x.cfg -c "adapter_khz 2000"
wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s)
dumped 131072 bytes in 1.445699s (88.538 KiB/s)
This is 3.7 times faster for writing and 14.3 times faster for reading
compared to the generic sysfsgpio driver; probably the writing speed is
limited by the target itself here and reading speed might be considerably
higher too with appropriate connection and a capable target.
BCM2835 name is choosen over BCM2708 because the published peripherals
datasheet uses the particular model name and not family name.
Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/758
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updated OpenJTAG driver from www.openjtag.org to work with latest version of OpenOCD.
Change-Id: I2917f4e5835fb9ca5265e81dc38515fa97ae9503
Signed-off-by: Ryan Corbin <corbin.ryan@gmail.com>
Reviewed-on: http://openocd.zylin.com/1406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add target code for Andes targets.
Change-Id: Ibf0e1b61b06127ca7d9ed502d98d7e2aeebbbe82
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1259
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andes AICE uses USB to transfer packets between OpenOCD and AICE.
It uses high-level USB commands to control targets instead of using
JTAG signals. I define an interface as aice_port_api_s. It contains
all basic operations needed by target-dependent code.
Change-Id: I117bc4f938fab2732e44c509ea68b30172d6fdb9
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1256
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is reported as working by mitsakos on IRC.
Change-Id: I26b97779c3e8e237c5b3996aa81183031b12ec0c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1419
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit d9ba56c295 did a bunch of
renaming of cortex_a8 to cortex_a, including the names in config
files. However that introduced a regression as the name in target_type
struct remained unchanged.
This adds the last missing bit: actual renaming of the target name as
understood by OpenOCD.
Also change the (hopefully) last instance of using it in the supplied
config files, namely from imx6.cfg.
Change-Id: Ib9289fc6d946630133ec6e36c20015ccb50acf61
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1420
Tested-by: jenkins
Reviewed-by: Chris Johns <chrisj@rtems.org>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is needed for configs that might be used with the cheapest
STM32F100 parts that have only 4kB SRAM.
Restrictions for the other STM32 families are verified to be set
appropriately.
Change-Id: I1ad2370435015604db9f27c1a76c153480311a28
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1378
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to reports of newer targets using a updated version of the ICEPick tap
rather than add another tapid we ignore the tap version.
Also see Trac 49 for details.
Change-Id: Ic78414c54af2545c817e1bb2c860970c1b587259
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1373
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Rename cortex_a8 target to use a more correct cortex_a name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: I0eb1429c9281321efeb444b27a662a941a2ab67f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1130
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
As requested, here is the target configuration that I'm using for an
STLink-V2-attached STM32W108C8. For some reason, it only seems to work
with "reset_config trst_only".
Change-Id: Icbff4f83343e1f505d8afdfc53ff6f8b7496cac9
Signed-off-by: Ben Nahill <bnahill@gmail.com>
Reviewed-on: http://openocd.zylin.com/1347
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
By default pic32mx starts after any reset with 1 wait state for RAM access/exec.
It can be changed to 0 wait states by clearing the BMXWSDRM bit (bit 6) in BMXCON register.
With 0 wait states near doubles the execution speed. CRC check sum can be done much faster
increasing verify_image speed. Fast data transfer also works with a bit higher scan rate, up to 1500 Khz.
This option can be set at any time with
mww 0xbf882004 0x40
or cleared with
mww 0xbf882008 0x40.
Some numbers for FTDI/HS with current devel code and a elf file:
Core clock / wait states verify_image speed
------------------------------------|------------------------------
4 Mhz / 1 21 KiB/s
4 Mhz / 0 36 KiB/s
8 Mhz / 1 37 KiB/s
8 Mhz / 0 57 KiB/s
Change-Id: I4092ad0f3753f72f77108718d0ed3a3ab84e3b23
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1141
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This config file add support to the opendous cable based on the chip ft2232H,
using the ft2232 interface driver.
Change-Id: I8171a0c475af8d61e081844ee86466a392138fb0
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1096
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config file add support to the opendous cable based on the chip ft2232H,
using the ftdi interface driver.
Change-Id: I4491f99d7b14f7078a04583ef0c4acd8692c4349
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This change adds a simple target configuration for Freescale
single/dual/quad core i.MX6 SoCs, only one core is configured by default.
Change-Id: I853dd27f4c6765b7f731be2ddea82e85d496c6a4
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-on: http://openocd.zylin.com/1135
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch change the default reset config from SYSRESETREQ to the working
VECTRESET.
Change-Id: I21a9a74b9c0c68cfa3a6e6dac9b123acc98a93cb
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1186
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update adds support for the STM32Lx 384kb dual bank flash. Previously there was a problem when writing an
image that was larger than 192Kb. That lead to openocd printing out two error messages like
"Error: access denied / write protected" and "Error: invalid program address". The reason was that the stm32lx
driver tried to write half pages which overlapped into the next flash bank.
A new configuration file stm32lx_dual_bank.cfg can be used for stm32lx chips with dual bank flash (256kb or 384kb devices).
A sanity check was added for probed flash size values to fix the issue seen on some ST samples that answered incorrectly.
Change-Id: I69e25131983d88613be8606b438f98870c5f1e52
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
adapter_init (core.c) won't check speed configuration
of the selected interface if it's not needed (.speed = NULL).
When it's not needed, we can now omit adapter_khz in
init scripts and we don't have to implement dummy handlers
for speed_div and khz functions.
It also removes calls to adapter_khz in interface configuration
files when not used anymore.
Change-Id: I6eb1894385503fede542a368f297cec6565eed44
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1131
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Limited (no page unprotect, no block writes) implementation of EFM32
flash support. Verified with EFM32 development kit and STLink V2 adapter
using SWD.
Change-Id: I3db2054d9aa628a1fe4814430425db3c9959c71c
Signed-off-by: Roman D <me@iamroman.org>
Reviewed-on: http://openocd.zylin.com/1106
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This part has 16k ram so make it all available.
Change-Id: Ifeb7bc850bfe4f68d0affb8f6a0931b4327e7257
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1006
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The smallest pert in the family has 10k RAM, so use that as a default
for the working area.
Change-Id: I78be0d14a254c109ac15a7163552c6132f810416
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1005
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Switch to using the internal HSI when a reset init is called, this also
matches the std stm32l cfg.
Read (verify) speed is increased from 17 to 120 KiB/s.
Change-Id: Ic94ba85949ffdefa17b7be45eef14e30f941d107
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1004
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
As part of the switch to using the hla for the stlink interface we rename
the cmds to a more generic name.
Update scripts to match new names.
Also add handlers for deprecated names.
Change-Id: I6f00743da746e3aa13ce06acfdc93c8049545e07
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/921
Tested-by: jenkins
Even though the stlinkv1 and stlinkv2 use different usb classes they share
the same layout scheme.
Merge the two into a common layout, thus enabling us to support other
adapter layouts.
Change-Id: I7d02c44a7f94ebc7f2cb5428b02ee40294fb430d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/918
Tested-by: jenkins
As for openocd 0.6.0-rc2 the function mips32_pracc_fastdata_xfer()
should now work at a scan frequency up to 1200Khz.
Mainly usefull to increase programming speed.
Also verify_image should be slightly faster.
Change-Id: I1e9b2be73690a4597e2f6ba069c1205026850f07
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/805
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added a new configuration file for LPC18xx based boards, such as
HitexLPC1850RevA Evaluation Board, and all other based on the
same microcontroller by NXP.
Change-Id: I68c3827be535b6d09a5c70b6d57191937d00354d
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/930
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config file is intended as an example of how to
use the lpcspifi flash driver, but it should be functional
for most LPC1850 boards utilizing SPIFI flash.
Change-Id: I855854282336701fd210134497ce014017f3aaec
Signed-off-by: Gianluca Renzi <gianlucarenzi@eurekelettronica.it>
Reviewed-on: http://openocd.zylin.com/929
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
this avoid driving nSRST high after startup, by making sure the nOE is
initialized inactive/high.
This also matches the config used for the STM32-PerformanceStick.
Change-Id: I9376de575b7dc834310d57dbd58575d51f60183e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/878
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
The cortino uses a direct srst connection rather than via any buffer.
As a result this fixes issues with the newer ftdi driver.
Change-Id: I28f6781bccae24de79aa6a03161f298a14fe2581
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/850
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This hardware uses a output enable buffer that was not correctly defined.
Fixes issues when using the new ftdi driver.
Change-Id: Iba6235a71a6d3c7d16ab729f858b336a4574dfea
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/844
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
The str9-comstick uses a direct srst connection rather than via any buffer.
As a result this fixes issues with the newer ftdi driver.
Change-Id: I0968e8459997a6a2b7bf0c46e89662cd57b4f496
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/842
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Added a flash driver designed to allow program/erase of
memory-mapped SPI flash chips for LPC43xx/LPC18xx family
micros. This driver includes three algorithms - erase,
write, and SPIFI peripheral initialization (to allow
memory-mapped access after a reset). The driver has been
added to the flash driver table (drivers.c), and the
OpenOCD documentation has been updated to include the flash
driver configuration command.
Change-Id: I79f4ff8f1f07de4e5f2fe4f8c23aeb903f868514
Signed-off-by: George Harris <george@luminairecoffee.com>
Reviewed-on: http://openocd.zylin.com/783
Tested-by: jenkins
Reviewed-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This driver implements a bitbang jtag interface using gpio lines exported via
sysfs.
The aim of this driver implementation is to use system GPIOs but to avoid the
need for an additional kernel driver.
A config suitable for RaspberryPi is included.
Change-Id: Ib2acf720247a219768d1cbfeebd88057ed2d7b8b
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Reviewed-on: http://openocd.zylin.com/762
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
DISTORTEC's JTAG-lock-pick Tiny 2 is a new interface using FT232HL chip
and layout similar to KT-LINK.
Change-Id: I2831b169cd448ca70397f2dd86c5b749dda3dabf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/787
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the target supports SYSRESETREQ make sure we use that as the default
if srst is not fitted/configured.
Change-Id: I24c907493134506320e69c1218702930629c1cdc
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/792
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This file is already included as olimex-arm-usb-ocd.cfg.
Change-Id: I0e66977c58e74ac93a0dc3a0c88a5e5af4992f8b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/780
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The embedded projects shop released a new highspeed version of
the openocd-usb adapter. These configuration files adds support
for it.
Change-Id: I9b23d7889f998712b9041af101e3f0b9aba85b28
Signed-off-by: Andrew Karpow <notandyk@gmail.com>
Reviewed-on: http://openocd.zylin.com/771
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Add cfg files for Hitex LPC1768 Stick
Website: http://www.hitex.com/?id=1602
This board has a FTDI2232D as JTAG interface, using the
same layout as the Hitex STM32-PerformanceStick but with
different USB PID.
Main MCU is a LPC1768 from NXP.
The interface config uses the ftdi driver instead of ft2232.
The corresponding ft2232 layout would be "stm32stick".
Change-Id: I1fd15588c5af35f7d51777d1ad958cc1dc72c6f7
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/763
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
part 4 - files that are currently untested
Change-Id: Ic4a08fdefc99e7a9d50885c888c3fca60ffa39bd
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/750
Tested-by: jenkins
part 3 - files that are currently untested but verified with schematics
Change-Id: Ia00c3b6437bffcfa0d178e779926ad9309e289fe
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/755
Tested-by: jenkins
part 2 - files that are currently untested but assumed to work, as other configs using the same layout work
fine
Change-Id: Ifaa1904227ebdc394362ccaf3ad3c5384a716657
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/754
Tested-by: jenkins
part 1 - files that were tested an verified as working fine
Change-Id: If5986853a1cf118a9eb3b4c13b036d0f71c39624
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/534
Tested-by: jenkins
- Moved variant-independent code to lpc17xx.cfg, which will be included from
lpc17??.cfg files automatically.
- lpc1768.cfg filled with variant-dependent code.
Change-Id: I7dabe6ed7da7be640ed38c13aaaa096b8796d9a0
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/675
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These were deprecated in commit 69ac20a.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I047872f8cd61b42aaca6588ab75566219e4a3f5d
Reviewed-on: http://openocd.zylin.com/741
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add support for the new stm32f3x family from stmicro:
http://www.st.com/stm32f3
Change-Id: Icd1db95bb2767d9c0ecef24deefa92b4fdaa4f14
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/735
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updates the Kinetis NOR flash support to handle all known block and sector
sizes. Previously only 2kiB sectors were hard-coded, now all four known
combinations non-volatile sector sizes are supported.
The premise of separating Kinetis Program Flash (PFLASH) from FlexNVM is
also introduced. This means each "block" of flash (in Freescale terms) is
treated as a bank in OpenOCD. Correspondingly, the existing board
configuration for the TWR-K60M512 eval system is updated to recognize two
banks instead of one.
A board config for the TWR-K60F120M is also added.
Bank and sector erase and programming has been checked with both of the
mentioned eval boards.
Change-Id: Iae2d10ebf8f548d0a3698df5430bbbe1ccadc58a
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Reviewed-on: http://openocd.zylin.com/663
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Seems like an esthetic change, but it will allow easy support for
other lpc17xx devices.
Change-Id: I2cb953ce1afdd82f6ca65b38d5557a28416f895e
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the Sony Ericsson J100I Phone to the board configurations.
Change-Id: I083ddf067c8ecdfdda0404fe9e9df980dbb86fe8
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/631
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch add the TI Calypso CPU to the configuration files.
Change-Id: Ieb462960391c4a2c630d7a83699c3b6e8162ace9
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/630
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These events have been deprecated for a number of years, update any
remaining scripts to the new events.
Change-Id: Ic31ff388545ac8b3a500045699ca92c541b13f12
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/634
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
now it is supported.
Change-Id: Id3b2ca9a2270974a5f453323f9057ecece400c94
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The smallest stm32f0 has 4k sram, so use this as the default.
Change-Id: I9097be9608da92b1b9da504e5bacc1280c86907a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/603
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The busblaster.cfg was contributed on April 23, 2012 and is a
duplicate of dp_busblaster.cfg that was contributed on Oct. 23,
2011. Therefore, deleting the second version. Also, renaming
the original dp_busblaster.cfg to simply busblaster.cfg, as this
name is more concise.
Change-Id: Iccb1f10f53dbbb248b1ff4c6295eaf67c32247c1
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/622
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The newer versions of BeagleBone boards use the default vid/pid
pair for FT2232 debugging. Please see the following README:
http://beagleboard.org/static/beaglebone/latest/README.htm
On revision A3/A4 boards, the VID/PID were chosen to match the
TI XDS100v2 (0x0403/0xA6D0). On A5 and newer revisions when we've
given the authors of CCS the chance to update their software, the
generic FTDI VID/PID (0x0403/0x6010) will be used to simplify
installation of drivers for systems already having those drivers.
Change-Id: I44228eb2029162f23d084eb05bcfef39e615668d
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/619
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The working area used in the config was incorrect, we only have 8K on this
board not 16K as the original cfg was declaring.
Change-Id: Ie0309fb86d839bd3bc1ac9383905b581fac5c388
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/598
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This enable the user or board config to override the parameters
passed to stm32_stlink.cfg.
Required to fix a incorrect working area bug with the stm32vldiscovery.
Change-Id: I40a4f7913ff37d577d44b1f23befccf0317080a1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/597
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
reset_config is now supported by stlink, remove from the config as this
is a per board option.
Change-Id: I85208d2154502b8d3a098afe1d9a28d75820a7c0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/582
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a FT2232 based USB JTAG dongle
Change-Id: Ibed773a23b6446df62fe4eac16c27fb2d741f4c3
Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-on: http://openocd.zylin.com/589
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Use one board file per eval board, so that the filename matches the
exact board the user has / wants to use. Merging different boards into
one file is confusing.
Change-Id: I7c50233924a87a913723d7215c4851039c2971bc
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/566
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add initial TCL support for the pandaboard-es which is
based on the omap4460 from Texas Instruments.
Change-Id: Ic63588721487feb95e7cb3d41cfaab0d2f181766
Signed-off-by: David Anders <danders.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/573
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
this patch adds the initial support for the omap4460 es1.0
version which is similar to the omap4430 and used on the
pandaboard-es.
Change-Id: If885f7d9f8809929bd799786b539e4f499fa3478
Signed-off-by: David Anders <danders.dev@gmail.com>
Reviewed-on: http://openocd.zylin.com/572
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
* Added support to the FT2232 driver for the FT2232H-based
Digilent HS1 adapter.
Change-Id: Iab6cc15f299badaf115615b5d4d785ecb2273c27
Signed-off-by: Stephane Bonnet <bonnetst@hds.utc.fr>
Reviewed-on: http://openocd.zylin.com/558
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for the KaRo TX25 module on a StarterkitV base board.
For board details, check http://www.karo-electronics.com/tx25.html
Change-Id: I2c80c5467bc476955b55196728aa3c37c8185e6c
Author: Simon Widmer <simonxwidmer@gmail.com>
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Reviewed-on: http://openocd.zylin.com/557
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a digital oscilloscope which uses a Samsung S3C2440 internally.
http://randomprojects.org/wiki/Voltcraft_DSO-3062C
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Change-Id: I5e28c3a8f30665a162e34c831294e4e658a16ebb
Reviewed-on: http://openocd.zylin.com/548
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This adds support for the STM32F4 target and the STM3241G Eval Board, in
both standalone and using the onboard STLINK.
Change-Id: I62f8908b5880568b2b36c78a78f94c40861ff335
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/540
Tested-by: jenkins
The SAM3A/X processors that were released thus far is either
a SAM3A/X(4) - 256K, or a SAM3A/X(8) - 512K device. Thus
the config files are per variant, and not per device.
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Change-Id: I84d26d044e810eb428b1d6287907ea3bf8364c73
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/522
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Chris Morgan <chmorgan@gmail.com>
Change-Id: I082b0d3092c7f3b2ee6b68af64d48c78b31f1dbf
Reviewed-on: http://openocd.zylin.com/510
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Split out functions specific to the AM335x SOC into the target directory and simplified the board config
file. This should allow one to quickly create new configs for boards based on the TI processor family.
Change-Id: I0c3db97950dfa832f1f1918fc10c180f068bba74
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/489
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Simplified the configuration and removed things that were not necessary for debugging. Also added reset
configuration.
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Change-Id: I96f991c3051aa68278212cd6509484cbce40ccb7
Reviewed-on: http://openocd.zylin.com/488
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Moved ti_beaglebone.cfg to the board configuration directory. This was
originally placed in the wrong location.
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Change-Id: I05d10b62b1a21618635ee1773c30d77dc756ec82
Reviewed-on: http://openocd.zylin.com/481
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for the Beaglebone board based on the am335x processor
family. After much trial and error, I was able to configure the
Icepick-D and connect to the processor, halt execution, and run a sample
program. This is a unified config file (it doesn't use any include
statements) and further work needs to be done to split out the icepick-d
configuration to be more generic.
Change-Id: Ia1b8e9f01f56bd4f8c575ba3d0160c248583a15e
Signed-off-by: Neil Jensen <neil30al@gmail.com>
Reviewed-on: http://openocd.zylin.com/471
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The stm32 family supports using SYSRESETREQ as a software reset, lets
use it.
Change-Id: I171ffa8d888a2d0c28b266051030311521e9bca9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/472
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
This sets the default stellaris working area to 2k rather than
the current 8k. 2K is the smallest RAM size in the stellaris family.
Change-Id: I1407f758eb0926cc094b824a6d25199b313c45de
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/458
Tested-by: jenkins
Added the file imx28.cfg to the target directory
Added the file imx28evk.cfg to the board directory
Change-Id: I02a74a03f3773892f830d13660ffdded34f3261d
Signed-off-by: James Robinson <jmr13031@gmail.com>
Reviewed-on: http://openocd.zylin.com/428
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32L ref manual (RM00038 Rev5) states the SW-DP id should be 0x4ba00477.
The correct value from silicon is 0x2ba01477 - the typo has been confirmed by ST.
Change-Id: Ie35a1f13dc5dedc1b148fb219c6974bfa48b537c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/441
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This enables the user to override the transport used for st-link.
If JTAG is selected it will also change the default id used to the JTAG id
rather than the SW-DP id.
Change-Id: I4fe352e4932e2f4ec278168e99ba2d2d50fd850a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/443
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Make _TARGETNAME variable global so it could be used by scripts sourcing it.
Change-Id: Iaf1c3b53875734658b1b8f136c9bb958988b56bf
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/421
Tested-by: jenkins
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This patch add jtag support to the stlink driver add
two new transport types, JTAG and SWIM.
Change-Id: I7089d74250330be5c6a01c24066307641df7d11e
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/393
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This only effects the older Stellaris LM3S811 kits (rev B and below).
Change-Id: Ie068cce7748fede9e7113ea63a69c96222c809fa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/401
Tested-by: jenkins
This affects all configurations including target/at91sam3XXX.cfg
Change-Id: I2c1e1edf0986d30e63f109604a38bf402ded369e
Signed-off-by: Ulf Samuelsson <ulf@emagii.com>
Reviewed-on: http://openocd.zylin.com/292
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Renamed all functions, enums, structs and defines from mx2/imx27 to mxc. This is in preparation of adding support for mx35 NFC(v2).
Change-Id: I92ad23f0cfab605215bbf0d5846c5c288423facf
Signed-off-by: Erik Ahlén <erik.ahlen@avalonenterprise.com>
Reviewed-on: http://openocd.zylin.com/267
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Handle default case of single DDR chip
Propagate global variable for multi DDR chip
Change-Id: I315380f91ee7fcc2976437aa5836d88a7964fc9d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/251
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Commit 1794e5ee54 renamed the file to
have all lowercase characters according to most references to the
file, but the commit didn't change the existing reference to the
old filename.
Change-Id: I380e52e947a8091d48cf010e3919bf2caed7fdff
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/248
Tested-by: jenkins
Before this patch, at91sam3u4c.cfg includes "at91sam3uxx.cfg" which
doesn't exist - the filename was at91sam3uXX.
However, many operating systems have case sensitive file names!
Change-Id: I8b2f987f1f4214269b80ef5cba8177ce05ad90b6
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Reviewed-on: http://openocd.zylin.com/247
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fix error introduced in recent commit.
Correct the name of the board file.
Change-Id: I46bca8329812fb24bc4f8d316be9e7cba9b56496
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/234
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Initial support for SPEAr320 chip and for evaluation
board named EVAL_SPEAr320CPU.
Change-Id: I85524655769bcc610294a26db47a7a399256fbb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/231
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Initial support for SPEAr300 chip and for evaluation
board named EVALSPEAr300.
Currently supports only those parts in common with
SPEAr310.
Change-Id: I8075aa721cf3dfaac561ee51e5df4ce9a2992e3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/230
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code to autodetect DDR was wrong and not complete.
Replaced with a parameter passed to TCL proc.
Split DDR configuration in the two cases of single and
dual DDR chip, using single chip as default.
Change-Id: If39aa518670398e8e4f207d7db6e812a49743e15
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/229
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
DDR controller activation should not be in DDR chip
specific code, but in generic DDR controller part.
Change-Id: If1b178228352b48b0097d7b9b300005fb5bb4fb6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/228
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The support for SPEAr3xx family members does not require
dedicated files for each member.
Join the initialization scripts in a single file.
Change-Id: I45e9dc64809a6f52c4592e3e0eef5529394887c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/227
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The initialization of RAS enable and clock is required by
all SPEAr3xx devices
Change-Id: Iea4cd0902e4da219475d7f35b4c25fc87ec6b902
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/226
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The initialization of memory port 1 is required by
SPEAr310 only
Change-Id: I9d655da1026795f02ff2f82aed36441068cf266d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/225
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
ST-AN was mentioned but there was no reference
Change-Id: Ie065f8faba94d63cf391a994ec895692d499394e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/224
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on the K40/Kwikstik config files
Change-Id: Icb3adc7126bacea65209b712ebaa0eb3b894372e
Signed-off-by: Tomas Frydrych <tomas@sleepfive.com>
Reviewed-on: http://openocd.zylin.com/210
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a successor to the Flyswatter cable and is very close to the original.
The new revision is based on FT2232H.
Change-Id: Icc6efcf0e4f9d8a10b65df8679b4973f6b375a9f
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: David Anders <danders@tincantools.com>
Reviewed-on: http://openocd.zylin.com/193
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The main difference with at91sam7x256 is the declaration of the second
bank of flash.
Change-Id: I87a20dcbb639b797799139ccf46cc73934fa3b9e
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Reviewed-on: http://openocd.zylin.com/173
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Drop useless double-space occurences, drop trailing whitespace, and fix
some other minor whitespace-related issues.
Change-Id: I6b4c515492e2ee94dc25ef1fe4f51015a4bba8b5
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/137
Tested-by: jenkins
Also, drop author name from interface/hilscher_* files, that info is in the
git log, and none of the other files contain author names either.
Change-Id: Idf0eb4279c4bff31d15c166619c0bf8b1c5bb877
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/138
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for a KaRo TX27 CPU module on a StarterkitV base board.
The register settings have been extracted from a RedBoot distribution
that is distributed along with the hardware by KaRo.
This setup has been tested with a JTAGKey. The testing has been focussed
on loading a program into memory and start execution.
Although the flash seems to be correctly detected, no effort has been put
in testing the NAND programming yet.
Change-Id: Ib17763f1e3ecacd0eb9b5fdc32f8cba7a5e59be5
Signed-off-by: Mark Vels <mark.vels@team-embedded.nl>
Reviewed-on: http://openocd.zylin.com/158
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
There are many "force an error till we get a good number" comments in
target/board files. This refers to the use-case where a config script
sets _CPUTAPID to 0xffffffff (which presumely gets overridden later):
if { [info exists CPUTAPID ] } {
set _CPUTAPID $CPUTAPID
} else {
# Force an error until we get a good number.
set _CPUTAPID 0xffffffff
}
However, the same comment was also copy-pasted in many files which do
_not_ set _CPUTAPID to 0xffffffff, where the comment doesn't make any
sense at all. Drop those comments. Also, add one missing comment, and
fix small whitespace and grammar issues.
Change-Id: Ic4ba3b5ccba87ed40cea0d6a7d66609fbdfa3c71
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/136
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The STM3220G-EVAL board has an STM32F207IGH6. ("...H6", not "...T6").
Change-Id: Iaf3dae6830c5c0685a1dcd1588d391434bc51be7
Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
Reviewed-on: http://openocd.zylin.com/120
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The BusBlaster from Dangerous Prototypes is based on the FTDI FT2232H IC.
It has a CPLD between the FT2232H and the JTAG header allowing it to
emulate various debugger types. It comes configured as a JTAGkey compatible
device.
Change-Id: Iab56907bf67ded87001e628d93012f1e16287d90
Signed-off-by: Richard Barlow <richard@richardbarlow.co.uk>
Reviewed-on: http://openocd.zylin.com/53
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The Toshiba TMPA900 series (TMPA900/901) only has internal RAM regions
RAM-0 (16kB) and RAM-1 (8kB) which we can use as working area.
This is probably a copy-paste error from tmpa910.cfg, which has the
correct values and sizes for the TMPA910 series (TMPA910/911/912/913):
there are RAM-0, RAM-1, and RAM-2 (each 16kB).
Also, change "built-in RAM" to "internal RAM" to match what the
datasheet uses.
Change-Id: I993cd6b7fadc28cf34e5cc18426bb2bb42597670
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/34
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Using the ICEPick reset seems to allow the processor to be halted sooner
and the halt on gdb connection makes the connect process more robust.
Change-Id: I0586f6e6becc60a729030509ef58907a19d545ec
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/23
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This sets up simple functions that can later be used to provide additional
ICEPick Operations.
Change-Id: I313b8679267696fad87d23f3692963e513f2fe21
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/22
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
This is a Toshiba TMPA900CMXBG (ARM9) based SO-DIMM CPU module with 64MB
DDR SDRAM, 256MB NAND flash, and on-board Ethernet.
The board file provides a tonga2_init function which sets up the
PLL/clocks and memory (SDRAM and SRAM), which allows writing a boot-loader
into RAM via JTAG.
Change-Id: I60522b97997bdf50e1f25aebab910d93a98522fb
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/19
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Gumstix Verdex is a PXA270-based series of computer-on-modules. This
configuration file is based off the voipac.cfg configuration with
a different flash memory configuration. This has been tested flyswatter
adapter to reflash a Gumstix Verdex XL6P board.
Andreas Färber
Forest Crossman
Tim 'mithro' Ansell
Nemui Trinomius
Ivan Buliev
Christoph Pittracher
Andrey Yurovsky
Robert Jordens
Radek Dostal
Jiri Kastner
Alex Ray
Spencer Oliver
Paul Fertser
Felipe Balbi
Tomas Vanek
Uwe Bonnes
Ed Beroset
Jeff Ciesielski
Angus Gratton
Andreas Fritiofson
Matthijs van Duin
Arne Wichmann
Oleksij Rempel
Anton Kuzmin
Andreas Bomholtz
Joerg Fischer
Pawel Si
Jacob Palsson
Heinz Schweiger
Thomas Eichinger
Karl Palsson
Karl Palsson
Juha Niskanen
Rémi PRUD'HOMME
Austin Phillips
Vanya Sergeev
Бурага Александр
Eldar Khayrullin
Andrey Smirnov
Andrey Skvortsov
Fredrik Hederstierna
Thomas Schmid
Franck Jullien
Tom Rini
Marco Cruz
Yegor Yefremov
Ash Charles
Seth LaForge
Lee Bowyer
Tim Sander
Jens Hoffmann
Jörg Wunsch
Bartosz Bielawski
Tim Kryger
Fatih Aşıcı
Adrian Burns
Robert P. J. Day
Alex Murray
Sergey A. Borshch
Sergio Chico
Greg Ungerer
Pushpal Sidhu
Brad Riensche
Sergey Alirzaev
Marek Vasut
Laszlo Papp
John Szakmeister
Giuseppe Barba
Ryan Corbin
Hsiangkai Wang
Ben Nahill
Peter Dietzsch
Salvador Arroyo
Rodrigo Melo
Vladimir Zapolskiy
Mathias K
Johan Almquist
Roman D
is2t
Gianluca Renzi
Peter Stuge
George Harris
Marc Reilly
Freddie Chopin
Aurelien Jacobs
Andrew Karpow
Vandra Akos
Christopher Kilgour
Bill Traynor
Olivier Schonken
Allen Martin
Uwe Hermann
David Anders
Stephane Bonnet
Wjatscheslaw Stoljarski (Slawa)
Simon Widmer
Chris Morgan
Jan Dakinevich
Øyvind Harboe
Jim Norris
Jaap de Jong
Neil Jensen
Jonathan Dumaresq
Lars Poeschel
James Robinson
Michel JAOUEN
John
Erik Ahlén
Ulf Samuelsson
Antonio Borneo
Harald Welte
Tomas Frydrych
Felix Ruess
Mark Vels
Marti Bolivar
Richard Barlow
Karl Kurbjun
Clément Burin des Roziers
Ash Charles