The driver aice defines the command 'aice serial' to specify the
serial string of the adapter, but actually does not use this value
in the code.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I892e0a4e1b41a7a87adf54a5736abf7419f32979
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6648
Tested-by: jenkins
GD32E23x from GigaDevice is cortex-M23 microcontroller and it can work with the stm32f1x driver.
Modifications are similar to this done for GD32F1x0 in #6164 (https://review.openocd.org/c/openocd/+/6164).
Configuration file is added because its cortex-M23 CPU ID is different.
I think that GigaDevice microcontrollers should be handled in an independent unit to separate them from STM32,
but nowadays quick solution is welcome.
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Change-Id: I91f31f5f66808bc50a8f607ac2c107e6b7c5e2b8
Reviewed-on: https://review.openocd.org/c/openocd/+/6527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This primarily contains the large upstreaming of RISC-V changes, so lots
more RISC-V changes than usual.
Conflicts:
src/target/riscv/opcodes.h
src/target/riscv/riscv-011.c
src/target/riscv/riscv-013.c
src/target/riscv/riscv.c
src/target/riscv/riscv.h
Change-Id: I1145dad538a5470ad209848572e6b0f560b671e9
Signed-off-by: Tim Newsome <tim@sifive.com>
Freeze the IWDG watchdog when cores are halted to prevent a reset
while debugging.
The PMIC present on some board senses the nsrst and forces a power
cycle to the target. The power cycle causes the SWJ-DP to restart
in JTAG mode. If the debugger is using SWD, the mismatch triggers
an error after the reset command.
Ignore the error detected by 'dap init' and proceed executing the
handler. The error in 'dap init' will force a reconnect during the
following 'dap apid', restoring the SWD functionality.
Change-Id: I04fcda6a5b8a1b080ab4e8890ecd0754d5ed12d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6599
Tested-by: jenkins
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
do not force the presence of the reset line, since some custom boards
may do not contain the reset line.
Change-Id: I031ab34012b34a1b49def9db16461f9de0ae29cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Fleck <fleckz@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/316/
Reviewed-on: https://review.openocd.org/c/openocd/+/6506
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
known boards are NUCLEO-G431KB, NUCLEO-G431RB and NUCLEO-G474RE
note: this work safely with B-G431B-ESC1, B-G474E-DPOW1,
STM32G474E-EVAL and STM32G484E-EVAL
Change-Id: I132a97e1816620b182983edc8a4b272b52b9241d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5484
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G031K8, NUCLEO-G070RB, NUCLEO-G071RB
note: this work safely with STM32G0316-DISCO, STM32G071B-DISCO
and STM32G081B-EVAL
Change-Id: I483b6f44409228cd8c2c97b3c560927d1645c517
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5483
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
After compiling OpenOCD from source (commit: 6edf98db7), OpenOCD could not connect with the target board which is a GD32VF103T_START development board,
when I used the command: openocd -f "interface/cmsis-dap.cfg" -f "target/gd32vf103.cfg"
Issue 1: The clock speed hasn't been set, the error message given is:
Error: CMSIS-DAP command CMD_DAP_SWJ_CLOCK failed.
Which can be solved by adding a clock speed setting to the gd32vf103.cfg file:
adapter speed 1000
Issue 2: The default transport is not set to jtag, which it requires, the error shown is:
Open On-Chip Debugger 0.11.0+dev-01861-g6edf98db7-dirty (2021-08-25-10:18)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "swd". To override use 'transport select <transport>'.
embedded:startup.tcl:128: Error: session transport is "swd" but your config requires JTAG
in procedure 'script'
at file "embedded:startup.tcl", line 26
in procedure 'jtag' called at file "/home/user/riscv-openocd-tool/usr/local/bin/../share/openocd/scripts/target/gd32vf103.cfg", line 9
in procedure 'default_to_jtag' called at file "embedded:startup.tcl", line 133
at file "embedded:startup.tcl", line 128
This issue can be solved by adding the line:
transport select jtag
After adding these two lines, OpenOCD could connect to the development board successfully. Programming the flash also works.
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for ECP5 FPGA targets and board based on this chips:
Radiona ULX3S and Lambdaconcept ECPIX-5
Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6112
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The V3U SoC is unique in that it now has 8x CA76 and CR52,
while the previous SoCs had CA57/CA53/CR7 . This can still
be handled without too complex modifications to the gen3
configuration file, so add the logic to handle it there.
Change-Id: I7ab33eacc1fd379d369988d3d6690d2e82346c7e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On SMP Renesas R-Car Gen2/Gen3 systems, select the boot core as
the default target using the 'targets' command. This way, the
user can start debugging code running on the boot core without
having to switch to the boot core by explicitly invoking 'targets'
command first, since it is likely the debugged code will run on
the boot core. Note that most of the code is already in place, it
was just not used, so this is more of a fix to make the original
intention work.
Change-Id: I727808adce617c1d9ebd6ffa34f60f5882cdae60
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6313
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: use unsigned int for FPB and DWT quantifiers
related quantifiers are:
- fp_num_lit
- fp_num_code
- dwt_num_comp
- dwt_comp_available
Change-Id: I07dec2d4aa21bc0e580be0d9fd0a6809f876c2a8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6185
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* telnet: allow hiding selected commands during auto-completion
We have TCL procedure and commands that we do not want to show in
the list of auto-completion. E.g. TCL wrappers for deprecated
commands, internal procedures that are not supposed to be exposed
to user, or even commands that the user decides to hide.
Create a TCL procedure to be called by telnet auto-complete code
in place of the hard-coded TCL command. The procedure will run the
same command and will filter-out the unwanted command names.
Initialize the list of commands to be filtered-out with the name
of the TCL procedure above, as it is considered as internal.
Change-Id: I2d83bbf8194502368c589c85cccb617e69128c69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6194
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* telnet/auto-complete: hide deprecated and internal commands
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* startup.tcl: prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl: [1/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl: [2/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
* tcl: [3/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/stm8: Make 'stm8_command_handlers' static
Change-Id: I5237a8f2a1ecba9383672e37bd56f8ccd17598b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6200
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: Change 'authdata_read' output
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* Enable adapter "Bus Pirate" by default.
The Bus Pirate is now listed in the "OpenOCD configuration summary" too.
Change-Id: Ieb7bf9134af456ebe9803f3108a243204fb2a62d
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/5637
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* coding-style: additional style for C code
To improve readability and to push more uniform code style.
Prefer 'if (false) {...}' for unused code so it get checked by the
compiler.
Define preferred indentation for 'switch' statement.
Require balanced brackets in 'if/else'.
Report the max line length.
Report the formatting strings for stdint/inttypes types.
Report the type 'target_addr_t'.
Prefer 'unsigned int' to 'unsigned'.
Change-Id: I0192a4ed298f6c6c432764fdd156cffd4b13fc89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6203
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
* Add IPDBG JtagHost functionality to OpenOCD
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/nor/xcf: Do not use 'Yoda conditions'
Change-Id: I17308f5237338ce468e5b86289a0634429deaaa9
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6201
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: add armv8m special registers
Change-Id: I1942f375a5f4282ad1fe4a2ff3b8f3cbc64d8f7f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6016
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: Add support for Zephyr RTOS
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/armv7m.h: [style] replace tab with space between variable type and name
Change-Id: I9740c25857295a2a655d3046322a3f23f0ee7f78
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6230
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* server: gdb_server: Add colon for target extended-remote
Both GDB commands "target remote" and "target extended-remote" require
to have ":" right before port number.
e.g.
(gdb) target extended-remote :3333
Add ":" to the warning message so that users can copy & past it.
Change-Id: Id6d8ec1e4dfd3c12cb7f3b314064f2c35fa7ab55
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6237
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* jimtcl: restrict memory leak workaround on Linux only
The workaround for jimtcl 0.80 in commit 36ae487ed0 ("jimtcl:
add temporary workaround for memory leak in jimtcl 0.80") issues a
compile time error on macOS:
../src/helper/command.c:157:22: error: aliases are not
supported on darwin
__attribute__((weak, alias("workaround_createcommand")));
The OS is x86_64-apple-darwin19.6.0 and the compiler used is
x86_64-apple-darwin13.4.0-clang.
Restrict the workaround on Linux host only. The fix for 'expr'
syntax change is already merged and the workaround will be dropped
soon.
Change-Id: I925109a9c57c05f8c95b70bc7d6604eb1172cd79
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adam Jeliński <ajelinski@users.sourceforge.net>
Fixes: 36ae487ed0 ("jimtcl: add temporary workaround for memory leak in jimtcl 0.80")
Fixes: https://sourceforge.net/p/openocd/tickets/304/
Reviewed-on: http://openocd.zylin.com/6241
Tested-by: jenkins
* target/armv7m: fix static analyzer warning
Despite of assert(is_packed) clang static analyser complains on use
of the uninitialized offset variable.
Cross compiling with latest x86_64-w64-mingw32-gcc hits warnings
src/target/armv7m.c: In function ‘armv7m_read_core_reg’:
src/target/armv7m.c:337:54: error: ‘reg32_id’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
It happens because mingw32 defines assert() without the attribute
"noreturn", whatever NDEBUG is defined or not.
Replace assert(is_packed) by if (is_packed) conditional and call
assert(false) in the else branch.
Change-Id: Id3c7dcccb65106e28be200b9a4d2b642f4d31019
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
* cmsis_dap: fix build on macOS
Compile fails with error:
src/jtag/drivers/cmsis_dap.c:683:28: error: format specifies type
'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
" received 0x%" PRIx8, CMD_DAP_TFER, resp[0]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
Fix the format specifier.
Change-Id: I0a5a1a35452d634019989d14d849501fb8a7e93a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6255
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* cortex_m: do not perform soft_reset_halt on targets without VECTRESET
Change-Id: Ib3df457e0afe4e342c82ad1af25e03aad6979d87
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6209
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* cortex_m: fix VECTRESET detection for ARMv6-M cores
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/arm_dpm: rename 'wp_pc' as 'wp_addr'
The field 'wp_pc' was originally introduced in commit 55eeea7fce
("ARMv7a/Cortex-A8: report watchpoint trigger insn") in end 2009
to contain the address of the instruction which triggered a
watchpoint. Later on with commit 651b861d5d ("target/aarch64:
Add watchpoint support") it has been reused in to hold directly
the memory address that triggered a watchpoint.
Rename 'wp_pc' as 'wp_addr' and change its doxygen description.
While there, fix the format string to print the field.
Change-Id: I2e5ced1497e4a6fb6b38f91e881807512e8d8c47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6204
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
* target/aarch64: fix watchpoint management
The early documentation for armv8a report the debug register WFAR
as containing the address of the instruction that triggered the
watchpoint. More recent documentation report the register EDWAR as
containing the data memory address that triggered the watchpoint.
The name of macros CPUV8_DBG_WFAR0 and CPUV8_DBG_WFAR1 is not
correct as they point to the debug register EDWAR, so reading such
register returns directly the data memory address that triggered
the watchpoint. The code incorrectly passes this address value to
the function armv8_dpm_report_wfar(); this function is supposed to
adjust the PC value, decrementing it to remove the effects of the
CPU pipeline. This pipeline offset, that has no meaning on the
value in EDWAR, caused commit 651b861d5d ("target/aarch64: Add
watchpoint support") to add back the offset while comparing the
address with the watchpoint enabled.
The upper 32 bits of EDWAR are not valid in aarch32 mode and have
to be ignored.
Rename CPUV8_DBG_WFAR0/1 as CPUV8_DBG_EDWAR0/1.
Remove the function armv8_dpm_report_wfar().
Remove the offset while searching the matching watchpoint.
Ignore the upper 32 bits of EDWAR in aarch32 mode.
Fix a comment and the LOG text.
Change-Id: I7cbdbeb766fa18e31cc72be098ca2bc501877ed1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6205
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
* flash/stm32l4x: add missing break statement
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
* github/action: create a permanent 'latest' release
this commit extends the existing snapshot action to create a release named
'latest' with the built binaries for windows.
this 'latest' release will be updated after every push to github.
Change-Id: I75a64c598169241743add3ac9aa7a0337fbab7f2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6127
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* tcl/rp2040: remove empty line at end of file
Change-Id: I212a96b77282b151a8ecbd46a6436e2bbbda4161
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6221
Tested-by: jenkins
* tcl: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
* flash: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
* jtag: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I101c76a638805d77c1ff356cf0f027552389e5d3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6216
Tested-by: jenkins
* target: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
* openocd: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
* Document the buspirate interface driver.
Change-Id: Iaff13fc5187041a840f4f00eb6b4ee52880cf47e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Warn on undefined preprocessor symbols
Preprocessor directives like "#if SYMBOL" silently replace undefined or
misspelt symbols with 0, which makes configuration bugs hard to spot.
Compiler flag "-Wundef" prevents such errors.
Change-Id: I91b7ba2db02ef0c3c452d334601c53aebda4660e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6238
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Remove compatibility macros m4_ifblank and m4_ifnblank
They are at least since Autoconf 2.67 present,
and we are requiring version 2.69.
Change-Id: I41b33d4ebe02198f03cdddcc4a3c1beedd993d78
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure.ac: use a separate folder for Autoconf-generated files
Autoconf generates several files in root folder of the project.
Keep the root folder cleaner by specifying subfolder 'build-aux'.
Align .gitignore accordingly.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: Ied87faba495d9eeb8f98e78c2e2b7e7e596febfb
Reviewed-on: http://openocd.zylin.com/6236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* helper/command: silent debug msg on command register/unregister
Commit e216186fab ("helper/command: register full-name commands
in jim") and commit a7d68878e4 ("helper/command: unregister
commands through their full-name") introduce a LOG_DEBUG() message
each for command registration and unregistration.
The messages above are quite noisy and pollute the log when
debug_level is 3 or higher.
They can be useful to debug the command registration logic, but
for the other debug activities on OpenOCD are just noisy.
Already commit a03ac1ba30 ("helper/command: disable logging of
registered commands [RFC]") was merged to silent the first case
that is now back with additional logs.
Silent both log messages.
Use 'if (false)' to silent them, making easy to re-enable it when
or if someone needs it.
Change-Id: Id8a067e60e822d4ecbddcb036d081298f7e6181f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6220
Tested-by: jenkins
* mem_ap: fix target arch_info type
The target mem_ap appears as an ARM target, thus it allows the
execution of ARM specific commands causing the crash of OpenOCD.
E.g. 'arm mrc ...' can be executed and segfaults.
Replace the incorrect ARM magic number with a dedicated one.
While there, remove the 'struct arm', that is now holding only the
mem_ap's dap, and replace it with a pointer to the dap.
Change-Id: I881332d3fdf8d8f8271b8711607737b052a5699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6213
Tested-by: jenkins
* riscv: drop unused variable
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* riscv: replace macro DIM() with ARRAY_SIZE()
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/zynqmp : Add AXI AP access port
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* drivers/versaloon: use ARRAY_SIZE()
Replace the custom macro dimof() with the OpenOCD macro
ARRAY_SIZE().
Change-Id: I2fe638444f6c16f2a78c1fd558b21550f76282d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6259
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
* openocd: use macro ARRAY_SIZE()
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
* rtos: use ARRAY_SIZE() and simplify rtos_type.create()
Use the existing macro ARRAY_SIZE().
Rewrite the functions rtos_type.create() to simplify the logic.
Change-Id: I8833354767045d1642801d26944c9087a77add00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6261
Tested-by: jenkins
* tcl: remove remaining deprecated commands
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
* help text: remove trailing space
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
* help: fix line size in 'usage' output
The implementation of command 'usage' is broken while checking the
line limit of 76 chars per line (e.g. 'usage load_image') and the
line wrapping is not correct. The same broken code is used for the
first output line of command 'help' too.
When call command_help_show_wrap(), include the command's name in
the string so the whole text would be wrapped.
Change-Id: Idece01ce54994db7e851d8522435ff764b11f3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6223
Tested-by: jenkins
* LICENSES: Add the MIT license
Add the full text of the MIT license to the kernel tree. It was copied
directly from:
https://spdx.org/licenses/MIT.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I94a5dea5ced6421809ea2a3448f8dda19a93f5c9
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6219
Tested-by: jenkins
* stlink: add comment of firmware version for each flag bit
Change-Id: I7f7c7b9c9cfd88125f82662ed864a2c0715140b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6211
Tested-by: jenkins
* stlink: reorder the flag macro by firmware release
The corresponding bit for each macro is changed, but this is not
relevant in the code.
Change-Id: I7039464f5a3d55d008208f44952aadeb815bd5a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6212
Tested-by: jenkins
* tcl/board: Add ST NUCLEO-8S208RB
Change-Id: I384c6ad9b4cbabbc004160677f600d8c4bd3eb71
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6268
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/arm_adi_v5: Fix clear sticky overrun flag during replay of commands
When a WAIT occurs the commands after the WAIT are replayed and the
STICKYORUN is cleared. However if another WAIT occurs during the
command replay, the command itself is resent but the STICKYORUN bit
shall also be cleared. If this is not done, the MEM-AP hangs.
Change-Id: I14e8340cd5d8f58f4de31509da96cfa2ecb630d1
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6278
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: add support for watchpoints
The current implementation of OpenOCD does not support watchpoints for
cortex_a architecture. So, I replaced the add_watchpoint and
remove_watchpoint with the specific implementation for the
cortex a and using the breakpoint implementation and the arm
documentation [1] as reference. In particular, I have made the
following changes:
* added the following functions
- cortex_a_add_watchpoint
This wrapper function check whether there are any watchpoint
available on the target device by calling cortex_a_set_watchpoint.
- cortex_a_set_watchpoint
This function is responsible for settings the watchpoint register
pair. In particular, it sets the WVR and the WCR registers with
the cortex_a_dap command.
- cortex_a_remove_watchpoint
This wrapper function the selected watchpoint on the target device
by calling cortex_a_unset_watchpoint.
- cortex_a_unset_watchpoint
This function sets both the WVR and the WCR registers to zero, thus
unsetting the watchpoint.
[1]
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0464f/BCGDHIEJ.html
Change-Id: I86611dab474cb84836662af572b17636dc68e282
Signed-off-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Reviewed-on: http://openocd.zylin.com/3913
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
* target/cortex_a: fix number of watchpoints
Decrement the available watchpoints only when succeed setting it.
Initialize the available watchpoint with the correct value.
Change-Id: I0f93b347300b8ebedbcd9e718d4ba32b26cf6846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6196
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: add support for watchpoint length of 1, 2 and 4 bytes
Use byte address select for 1 and 2 bytes length.
Use normal mode for 4 bytes length.
Change-Id: I28d182f25145d0635de64d0361d456f1ad96640e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6197
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: fix memory leak on watchpoints
The memory allocated to hold the watchpoints is not freed at
OpenOCD exit.
Free the watchpoint memory at OpenOCD exit.
Change-Id: I518c9ce0dc901cde2913d752e3154734f878b854
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6210
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* helper/jim-nvp: comply with coding style [1/2]
The helper jim-nvp does not comply with OpenOCD coding style due
to typedef of struct and CamelCase symbol names.
While it's trivial fixing the helper and all its current use in
the code, changing these APIs will potentially break a number of
patches pending in gerrit. Gerrit will not trigger any alert, but
the code will generate compile error after the merge.
Add the compile flag "-Wno-error=deprecated-declarations" to keep
as warning (not as error) the use of "deprecated" functions and
types.
Rename all the CamelCase symbols is lowercase and provide struct
prototypes in place of the typedef.
Add a DEPRECATED section to 'jim-nvp.h' where the old CamelCase
symbols and the old typedef are re-declared with compile attribute
'deprecated'.
With this change OpenOCD compiles, but generates warnings.
The remaining changes allover OpenOCD code will be fixed in a
separate patch for easier review.
The patches merged later that still use the old deprecated API
will compile with warnings. This will permit to identify and fix
these cases.
Change-Id: I786385d0f662dbb1be5be313ae42623156d68ce5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6183
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* helper/jim-nvp: comply with coding style [2/2]
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
* server/telnet: fix autocomplete for jimtcl commands
Current autocomplete filters-out some command reported by "info
commands". One of the filter rule concerns the command's private
data.
Every command registered by OpenOCD has its 'struct command' as
private data.
By ignoring commands without private data, we loose several TCL
commands registered by jimtcl, e.g. 'foreach', 'llength'.
By assuming that every command with non-NULL private data has
'struct command' as private data, we risk at best to access
inconsistent data, at worst to trigger a segmentation fault.
Export the already available functions:
- to check if a command has been registered by OpenOCD and
- to get the private data.
While there, rename jimcmd_is_ocd_command() as
jimcmd_is_oocd_command().
Don't filter-out jimtcl commands with no private data.
Check the private data only on OpenOCD commands.
Change-Id: Ib5bf8d2bc5c12440c0cfae438f637c38724a79b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6282
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* helper/list.h: align file to Linux v5.12
Main improvement is in the doxygen comments.
Minimize the delta with kernel file.
Skip the functions hlist_unhashed_lockless() and
__list_del_clearprev() that are relevant only in kernel.
Remove gcc extension "omitted conditional operand".
Change-Id: I2e9ddb54cfe2fa5f7cf18f44726acd144e1f98b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6276
Reviewed-by: <rdiezmail-openocd@yahoo.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* contrib: add an example of using list.h
Change-Id: Ic3d399d7ad2e4d10677cf78d64968040941b74e5
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6280
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* helper/list.h: add mention to the example in contrib
Without such reference, it could be difficult to find the example.
Change-Id: Ia9ffb06bc1a45446c2c7b53197ab3400e1d8a9e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6281
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* tcl/target/stm32f4x: fix hardcoded chip name
Fixes: c945d6e616 ("tcl/target: start using the new TPIU/SWO support")
Change-Id: I4543c9a204f7b4b3b14e6eabc5042653106aff0e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6277
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
* Makefile: add special target .DELETE_ON_ERROR
The special .DELETE_ON_ERROR deletes the target file on recipe error.
Otherwise, an incomplete output file may be considered up to date
the next time around. .DELETE_ON_ERROR provides reasonable
protection at virtually no cost.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: I67dca47ae5ddf3786993c87b9991b3046a85f00b
Reviewed-on: http://openocd.zylin.com/6235
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: Log both incoming and outgoing GDB packets
- Made sure that also outgoing GDB packets are logged,
not only the incoming ones.
- Improved the treatment of non-printable characters
in the packets to make it more robust.
Prior to this change:
- Outgoing packets were not printed unless OpenOCD was
re-compiled with _DEBUG_GDB_IO_.
- Non-prinable characters were only treated in incoming
'X' packets.
After this change:
- Both incoming and outgoing GDB packets are logged
on debug_level >= 3, so that both directions of the
GDB channel are visible.
- Non-printable characters are checked for in every packet
so that hey do not interfere with the terminal.
Change-Id: I0613e57ae5059b3279b0abcb71276cf5719a8699
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/renesas_rz_g2: Introduce tcl config file for RZ/G2 devices
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* drivers/jlink: Remove trailing dots
This makes the messages consistent with most of the rest of
the OpenOCD output.
Change-Id: I915a01187e7fc317e02483ac0bbd39ec077d6321
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: Use 'bool' for 'reset_halt'
Change-Id: I974a6360ea7467067511541ac212f2e9d3de7895
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6262
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cmsis_dap: add support for swo commands
Replaced mixed snake_case_CamelCase with snake_case.
Define variables at first-use location.
CMSIS-DAP SWO specification:
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__swo__gr.html
Change-Id: Ieba79b16efd445143f964b614673d041aae74f92
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5820
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Add target_data_bits().
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid non-standard conditionals with omitted operands.
Fixes bug #257.
Change-Id: I05fc6468306d46399e769098e031e7e588798afc
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6271
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/startup.tcl: Do not use 'Yoda conditions'
Change-Id: I5e1bbaf032659dda1b365ef4ec6ea4a635d921ce
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6284
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix build.
Change-Id: I4f2667db91f84f07af354691aac5d4c9e3aea3fa
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Marc Schink <dev@zapb.de>
Co-authored-by: R. Diez <rdiezmail-openocd@yahoo.de>
Co-authored-by: Daniel Anselmi <danselmi@gmx.ch>
Co-authored-by: Evgeniy Didin <didin@synopsys.com>
Co-authored-by: Yasushi SHOJI <yashi@spacecubics.com>
Co-authored-by: Tomas Vanek <vanekt@fbl.cz>
Co-authored-by: Olivier DANET <odanet@caramail.com>
Co-authored-by: Thomas Gleixner <tglx@linutronix.de>
Co-authored-by: micbis <michele.bisogno.ct@renesas.com>
Co-authored-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Co-authored-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Co-authored-by: Jan Matyas <matyas@codasip.com>
Co-authored-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
I may have broken memory sampling with this merge.
Conflicts:
doc/openocd.texi
src/helper/command.c
src/jtag/drivers/ftdi.c
src/rtos/FreeRTOS.c
Change-Id: I2b7e09b2d3b244db546c5212532e6b48fb66dca4
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This file has been added to OpenOCD 0.5.0 in 2011, before gerrit
gets in use, with commit ba71e8c521 ("at91: add chip register
definition and generic init support").
The only procedure in the file has never been referenced in any
other part of OpenOCD. This procedure has syntax errors while uses
its argument 'cs' and several unmatched parenthesis, which clearly
highlights that it has never been used so far.
Gerrit does not report any patch aimed at fixing it.
Even if the file seems unused and could be removed, let's fix it
in the hope it could get used.
While there, remove some useless parenthesis and format it using
the new simplified syntax required by jimtcl 0.81.
Change-Id: Ied26456262e7b99de37667a8ce418f4f12e237bd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ba71e8c521 ("at91: add chip register definition and generic init support")
Reviewed-on: http://openocd.zylin.com/6157
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Both http://openocd.zylin.com/542/ and http://openocd.zylin.com/543/
introduce the same typo in the bitfield for initializing the l2
cache of imx53.
One year later, http://openocd.zylin.com/1461/ copy-pastes the same
typo.
The comment above the code show that it's really an error and not
the expected behaviour.
Fix the typo replacing the incorrect comparison '<' with a left
shift.
Change-Id: I43725731a2228e28a676215f76936fa289d9395e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e3b3273433 ("cfg: add imx53loco board config")
Fixes: 108a458ab8 ("cfg: add icnova_imx53_sodimm board config")
Fixes: e608ced330 ("ftdi/board: Add support for DENX M53EVK")
Reviewed-on: http://openocd.zylin.com/6156
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Chip is similar to imx8x series but has different cores at different
addresses.
Support for reduced versions is not yet available.
Tested on imx8qm-mek board
Change-Id: Ia34a80d561ab2849a570d8c375b936a45cbf45ca
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-on: http://openocd.zylin.com/5042
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The Broadcom BCM2711 used in Raspberry Pi 4
No documentation was found on Broadcom website
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711/
Change-Id: I3db6c9af520af8ab4c21ad35ff0f2db28efc0325
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6066
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Broadcom chip used in the Raspberry Pi 2 Model B
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2836
Change-Id: I50b040db213c5b72f63d5f5534c552426c7376f9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6068
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is the Broadcom chip used in the Raspberry Pi Model A, B, B+,
the Compute Module, and the Raspberry Pi Zero.
Partial information is available in raspberry pi website:
https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2835
Change-Id: Ifeb012952473d624327e8c010ac5c886d9473aa0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6067
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Create the TPIU and SWO device in target config file.
Replace the target event 'trace-config' with the TPIU/SWO event
'post-enable'.
Extend the existing code in the event handler to properly set the
gpio mode and speed to permit synchronous trace.
This patch is not exhaustive of all the targets that have SWO, but
has to be considered as an initial example.
Change-Id: If4bbf364c0d2aef3ae49951e76507a3b1cfd58e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5859
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Add board and target configuration files for
Ampere eMAG8180 board and Ampere eMAG processor.
Tested on an Ampere eMAG8180 development platform.
Change-Id: I222653f0fc12d25202a7e469db3594076cbc38ed
Signed-off-by: Anthony Ferranti <ferranti@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5569
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add basic connection details for AM654 and J721E SoCs from TI.
See AM65x Technical Reference Manual (SPRUID7, April 2018)
for further details: https://www.ti.com/lit/pdf/spruid7
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: https://www.ti.com/lit/pdf/spruil1
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
See AM64X Technical Reference Manual (SPRUIM2, Nov 2020)
for further details: https://www.ti.com/lit/pdf/spruim2
Change-Id: Ie5108c6ad6f1304a6bf5b9f81aa9ebd33b8a559d
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: http://openocd.zylin.com/5182
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
TCL expands the variables only if preceded by a dollar sign.
Add the missing dollar before the variable's name '_CPUTAPID'.
Change-Id: Icc5d0dddf24f75d12ee63fee69e1b265e842ca43
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Wes Cilldhaire <wes@sol1.com.au>
Fixes: c3166b43e4 ("tcl/target: Add QuickLogic EOS S3 MCU configuration")
Reviewed-on: http://openocd.zylin.com/6079
Tested-by: jenkins
Reviewed-by: TM <tommy_murphy@hotmail.com>
* configure: do not make Capstone dependency automagic
This adds regular ./configure options to control dependency on the
Capstone disassembly engine. See [0] for the rationale.
[0] https://wiki.gentoo.org/wiki/Project:Quality_Assurance/Automagic_dependencies
Change-Id: I3e16dc5255d650aa1949ccf896b26dc96e522a75
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5985
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure.ac: fix build with libusb0 and without libusb1
Driver 'openjtag' requires both libftdi and libusb1.
The current check is incorrect and the driver is built when
libftdi is present with libusb0 and without libusb1, which causes
the linker to fail resolving the required libusb1 symbols.
Remove the check for libusb0 on driver 'openjtag'.
Create a new adapters group LIBFTDI_USB1_ADAPTERS to hold the
driver 'openjtag'.
Change-Id: I1f5e554b519e51c829d116ede894639cb55a26aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5989
Tested-by: jenkins
* doc: fix over/underfull hboxes in PDF
This adds some cosmetic changes to make the PDF User Manual look
proper.
Building it now requires Texinfo 5.0 which shouldn't be problematic
according to [0]. Commit 79fdeb37f4 is
effectively reverted.
[0] https://repology.org/project/texinfo/versions
Change-Id: I990bc23bdb53d24c302b26d74fd770ea738e4096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5995
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* contrib: rpc_examples: haskell: fix ftbs with current libraries
And get rid of some warnings along the way.
Change-Id: I8fdbe1fa304276be6b0f25249b902b3576aa3793
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5987
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Makefile.am: fix override of target 'check-recursive'
To prevent executing the Jim Tcl tests, the makefile's target
'check-recursive' has been overridden in commit 56d163ce79
("jimtcl: update to 0.77, the current version, enable only
specific modules").
This causes a runtime warning during build:
Makefile:6332: warning: overriding recipe for target 'check-recursive'
Makefile:5098: warning: ignoring old recipe for target 'check-recursive'
Instead of override the makefile's target 'check-recursive',
prevent the recursion by re-assigning as empty the variable
SUBDIRS for this specific target only.
Change-Id: I03d1c467eba42316a59aeed4612d6bdbe6211282
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 56d163ce79 ("jimtcl: update to 0.77, the current version, enable only specific modules")
Reviewed-on: http://openocd.zylin.com/5986
Tested-by: jenkins
* contrib: udev file for Cypress SuperSpeed Explorer kit
lsusb output:
Bus 003 Device 011: ID 04b4:0007 Cypress Semiconductor Corp.
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x0007
bcdDevice 0.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 114
bNumInterfaces 4
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 0
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 1 AT-commands (v.25ter)
iFunction 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x00
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 4
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 5
bInterfaceProtocol 0
iInterface 0
Change-Id: I62f0300199da3551c8774a4a5a4cd106a3ab2904
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/3611
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: fix memory leak on multiple '-gdb-port' flag
In the odd case of multiple flags '-gdb-port' during 'target
create' or following 'configure', the new strdup()'ed value will
replace the old one without freeing it.
Free the old value (if it exists) before replacing it.
Change-Id: I1673346613ce7023880046e3a9ba473e75f18b8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6005
Tested-by: jenkins
* udev: fix permission for Ambiq Micro EVK's
Commit 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.") was
initially proposed as http://openocd.zylin.com/3429/ then replaced
by http://openocd.zylin.com/3980/
The initial proposal was for file '99-openocd.rules', in which
MODE="664" was the norm.
After merge of http://openocd.zylin.com/2804/ the new udev rules
in '60-openocd.rules' switched to MODE="660", but the evolution of
the above patch missed this change.
Switch udev rules of Ambiq Micro EVK's to MODE="660" and uniform
them to the rest of the file.
Change-Id: I4b4eea535184ee8569da3264bff4f1fafb5bce4d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 68e204f1e9 ("udev: Add rules for Ambiq Micro EVK's.")
Reviewed-on: http://openocd.zylin.com/6004
Tested-by: jenkins
* doc/style: fix doxygen error
Doxygen complains about non-closed nested comments:
doc/manual/style.txt:423: warning: Reached end of file
while still inside a (nested) comment. Nesting level 1
(probable line reference: 149)
This is caused by the string '/**' that is interpreted as the
beginning of a comment.
Escape the string to not let doxygen consider it as a comment
While there, replace @code/@endcode with @verbatim/@endverbatim to
properly render the line.
Change-Id: If2a27c4cf659326e317cc4ac8c0b313e97e40432
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5996
Tested-by: jenkins
* flash/nor/max32xxx: fix path of include file
The relative path should have three times '..'.
Issue identified by doxygen:
src/flash/nor/max32xxx.c:85: warning: include file
../../contrib/loaders/flash/max32xxx/max32xxx.inc not
found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Change-Id: Ie7b4948c6770b8acb9eff26e08eea32945ebb219
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5997
Tested-by: jenkins
* Doxyfile.in: fix build out-of-tree
When doxygen is built out-of-tree, it fails to find the generated
file startup_tcl.inc:
src/openocd.c:59: warning: include file startup_tcl.inc
not found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Add '@builddir@/src' to INCLUDE_PATH.
Change-Id: I51f2f6fe7224bba0f8b3db7219f9831de4e67139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5998
Tested-by: jenkins
* doc/manual/primer/jtag.txt: remove duplicated section name
The section name 'primerjtag' is used twice, causing doxygen to
complain:
warning: multiple use of section label 'primerjtag',
(first occurrence: doc/manual/primer/jtag.txt, line 107)
Rename one of them.
Change-Id: Id307915dbc51a7f647fab4fb28ab431e65344d61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5999
Tested-by: jenkins
* Doxyfile.in: exclude libjaylink from doxygen
When build using libjaylink as git submodule, doxygen includes the
libjaylink files and complains for multiple 'mainpage' comment
block, one in OpenOCD and the other in libjaylink:
src/jtag/drivers/libjaylink/libjaylink/core.c:37: warning:
found more than one \mainpage comment block! (first
occurrence: doc/manual/main.txt, line 1), Skipping current
block!
Exclude libjaylink submodule from doxygen.
Change-Id: I5e856817344c9f21f8c26f077a23c00b83cfbcb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6000
Tested-by: jenkins
* openocd: fix incorrect doxygen comments
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
* openocd: fix doxygen parameters of functions
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
* doc/manual/primer/autotools.txt: fix doxygen warning
Commit ab90b87778 ("configure: remove AM_MAINTAINER_MODE,
effectively always enabling all the rules") removes the configure
flag '--enable-maintainer-mode' and its documentation, but have
left a reference to the removed subsection 'primermaintainermode'
and this triggers a warning in doxygen:
doc/manual/primer/autotools.txt:21: warning: unable to
resolve reference to 'primermaintainermode' for \ref
command
Remove the obsoleted paragraph.
Change-Id: I56e69ef033d546d159745bed1b47c6105827e7ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ab90b87778 ("configure: remove AM_MAINTAINER_MODE, effectively always enabling all the rules")
Reviewed-on: http://openocd.zylin.com/6003
Tested-by: jenkins
* flash/stmqspi: fix build error with -Werror=maybe-uninitialized
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/flash/nor/stmqspi.c: In function ‘read_flash_id’:
/src/flash/nor/stmqspi.c:1948:6: error: ‘retval’ may be used uninitialized
Change-Id: Ifd8ae60df847fc61e22ca100c008e3914c9af79b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6012
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: fix build error with -Werror=maybe-uninitialized
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/target/riscv/riscv.c: In function ‘riscv_address_translate’:
/src/target/riscv/riscv.c:1536:13: error: ‘pte’ may be used uninitialized
Change-Id: I51e180b43f9b6996e4e4058db49c179b9f81bcdc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6013
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: [FIX] ARMv8-M does not support VECTRESET
ref: Arm®v8-M Architecture Reference Manual (DDI0553B.m)
D1.2.3: AIRCR, Application Interrupt and Reset Control Register
Bit [0] is RES0
Change-Id: I6ef451b2c114487e2732852a60e86c292ffa6a50
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6014
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* driver/ftdi: skip trst in swd mode
When using the adapter olimex arm-jtag-swd (to convert to SWD a
JTAG-only FTDI adapter), the pin trst on JTAG side is re-used to
control the direction of pin SWDIO on SWD side.
There is a single reset API at adapter driver to assert/deassert
either srst and/or trst. A request to assert/deassert srst can
cause also trst to change value, hanging the SWD communication.
In SWD mode, ignore the value passed to trst.
Change-Id: I5fe1eed851177d405d77ae6079da9642dc1a08f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6006
Tested-by: jenkins
* configure.ac: drop macro 'AC_PROG_CC_C99' from autoconf 2.70
The macro AC_PROG_CC_C99 has been obsoleted by autoconf 2.70 and
triggers a set of warnings from both 'aclocal' and 'autoconf'.
The test of AC_PROG_CC_C99 is now included in AC_PROG_CC.
For autoconf 2.69 and earlier the macro is still required, so
cannot be simply dropped.
Use a conditional test to avoid the warning on autoconf 2.70 but
still use AC_PROG_CC_C99 on older autoconf.
Change-Id: I5e8437f5a826fb63be6d07bcb5bb824f94683020
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6009
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* configure: drop macro 'AC_HEADER_TIME'
The macro AC_HEADER_TIME has been obsoleted by autoconf 2.70.
Not all systems provide 'sys/time.h', plus some old system didn't
allowed to include both 'time.h' and 'sys/time.h' because 'time.h'
was included by 'sys/time.h' and was not properly protected to
allow multiple inclusion.
The macro AC_HEADER_TIME helps to detect such odd case.
Nowadays all the systems properly protect 'time.h', so its safe to
unconditionally include 'time.h', even if it is also included by
'sys/time.h'.
The case of systems without 'sys/time.h' is already covered by
configure.ac through the directive
AC_CHECK_HEADERS([sys/time.h])
Remove the obsoleted autoconf macro and simplify the code by
including 'time.h' unconditionally and check HAVE_SYS_TIME_H to
include 'sys/time.h'.
Change-Id: Iddb3f3f1d90c22668b97f8e756e1b4f733367a7d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6010
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* README.macOS: explain how to install suitable Texinfo
Change-Id: Ic5906111f412eebd906a9be3fd0e133484def3eb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6026
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* jlink: fix device discovery when network is off
If user specifies a serial number for the jlink device, openocd
extends the search to network jlink devices too, without checking
if the host has a valid and functional network connection. If the
network is not functional, libjaylink returns error. This error
invalidates the discovery on USB, even if it was successful.
Factor-out parts of the jlink_init into separate jlink_open_device
function, use that function to firstly discover and match USB
devices and, if matching device was not found on the USB bus and
serial number was specified, repeat discovery and matching via TCP.
Fixes: https://sourceforge.net/p/openocd/tickets/294/
Change-Id: Iea0de1640d4e5b21ecc7e9c1dd6d36f214d647c2
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: http://openocd.zylin.com/6025
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* README: add missing items for 0.11
JTAG adapters
Cadence DPI, Cypress Kitpro, FTDI FT232R, Linux GPIOD, Mellanox rshim,
Nuvoton Nu-Link, Nu-Link2, NXP IMX GPIO, Remote Bitbang, TI XDS110,
Xilinx XVC/PCIe
Debug targets
AArch64, Cortex-M (ARMv8-M), ARCv2, MIPS64, RISC-V, ST-STM8
Flash Drivers
ATmega128RFA1, Atmel SAM, eSi-RISC, EZR32HG, MAX32, MXC, nRF52, PSoC6,
Renesas RPC HF and SH QSPI, SiFive Freedom E, ST BlueNRG,
STM32 QUAD/OCTO-SPI for Flash/FRAM/EEPROM, SWM050, TI CC13xx, TI CC26xx,
TI CC32xx, TI MSP432, Winner Micro w600, Xilinx XCF
Change-Id: I341618ac5d7189e4f98268cecd66c99447b72af8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6027
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
* The openocd-0.11.0-rc2 release candidate
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* Restore +dev suffix
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* steppenprobe: fix file permission
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.
Strip the execution permission.
Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
* github: fix github wokflow while pushing a tag
this fix permits to add correctly the generated artifact (windows binaries)
into the release section.
Change-Id: Ia982370d3a1e08c623ebcabb5ac97e9fb49d00e0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6047
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* doc: Fix type in Hooking up the JTAG Adapter
We are talking about adapter connectivity in this chapter. It should
be "dongles" instead of "cables".
Change-Id: I7bd4307765517375caa2af86dfc929d0ef66c3e6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6040
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
* doc/manual: Fix @subpage handling
The subpage "thelist" used to have a title "Pending and Open Tasks"
but the commit c41db358a0 changed it to "The List". With
@subpage, it now renders:
"The List of The List enumerates opportunities for"
instead of
"The List of Pending and Open Tasks enumerates opportunities for"
This commit fix it to
"The List enumerates opportunities for"
Change-Id: Ifee0dcd9b3c9f7e651a8748a7afda99eedea3c5c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6041
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* doc/manual: Fix function name typo
We have both the singular form, register_command(), and the plural form
register_commands().
Change-Id: I905ea83988b8ac70dd809b02d53b646aa4d66697
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6042
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Co-authored-by: Paul Fertser <fercerpav@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Jiri Kastner <cz172638@gmail.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Co-authored-by: Bohdan Tymkiv <bohdan200@gmail.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Co-authored-by: Yasushi SHOJI <yashi@spacecubics.com>
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.
Strip the execution permission.
Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
only core0 is brought up by bootloader
Change-Id: I1d6b5e6ba7498beadbf3805f4271f0197e411bd5
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/5980
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
- rename and cleanup to arm-usb-ocd-h-cjtag file to be consistent
- add copy of olimex-arm-jtag-cjtag.cfg as arm-usb-tiny-h-cjtag.cfg
- did not remove olimex-arm-jtag-cjtag.cfg (should be deprecated)
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use the board file name as <company>_<name>.cfg
Add the SPDX tag to workaround an error in checkpatch that fails
to recognize as valid a patch that only changes a file name.
Change-Id: I929cd9e5f9fe2e7386950643487534c9a5a05bc6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5931
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
regsub doesn't work correctly on macOS Catalina, which results in
an incorrect CHIPNAME derived from the current target. Since regsub
is only used by this target, replace it with a simple string search
for '.' followed by a substring. This is funcionally equivalent to
what the regular expression was doing, but instead relies in simpler
string operations that should have little to no differences
between systems.
Also, refactor CHIPNAME detection into proc stm32h7x_chipname, so
it's always retrieved in the same way without duplicating the code.
Change-Id: Ia9f63f56b508688e74278b022eaec47e503916e7
Signed-off-by: Alberto Garcia Hierro <alberto@garciahierro.com>
Reviewed-on: http://openocd.zylin.com/5872
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
in RM0399 rev2, there was these bits in DBGMCU_CR registers:
- DBGSTBY_D3 : bit 7
- DBGSTOP_D3 : bit 8
these bits have been changed to reserved in rev3
Change-Id: I9d10d90e383795dc8e25a117d59fa065dc594610
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5861
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In commit a1ce28b118 ("rename some target scripts to be
consistent with the rest") the following renames was applied, but
the old names are still referenced:
tcl/target/{sam7se512.cfg => at91sam7se512.cfg}
tcl/target/{sam7x256.cfg => at91sam7x256.cfg}
Fix the board files to use to correct target config filename.
Change-Id: I7698aa0da7db95c2bd9ba7ab8c260905a975c857
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
When OpenOCD is installed to the host the 'tcl' folder gets
usually installed in /usr/share/openocd/, thus having 'tcl' as
prefix of the target's file causes 'find' to fail.
Remove the 'tcl' folder prefix.
Change-Id: I3dc484c8de6af8f5aae4dd1b230522ee47ae2ba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5887
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This is a) broken and b) doesn't include anything other than the
(broken) target alias. Don't see any reason for it to exist.
Change-Id: I833635eeac392bf7c0c39f51ff2f76525ba2d406
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/5884
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added comment to ti-icdi.cfg specifying how to get serial and an example of
specifying hla_serial for ti-icdi devices. This has been implemented in revision
2121a8f92969804611412b705af8114697a647dc
Change-Id: I648458a4dea176beae6a3f1a4e5641d0206077eb
Signed-off-by: John Pham <jhnphm@gmail.com>
Reviewed-on: http://openocd.zylin.com/2528
Tested-by: jenkins
Reviewed-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
nrf52_recover was merged in pre "Handle Tcl return values consistently"
state - remove ocd_ prefixes.
Erase and unlock sequence was changed to comply Nordic semiconductor
recommendation:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fnwp_027%2FWP%2Fnwp_027%2FnWP_027_erasing.html
Change-Id: Ic54236c27cf25ad8091e9e572ba1ef846f0d47c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reported-by: Pieter De Gendt <pieter.degendt@gmail.com>
Reviewed-on: http://openocd.zylin.com/5845
Tested-by: jenkins
Reviewed-by: Pieter De Gendt <pieter.degendt@gmail.com>
Used histogram diff strategy, which was much better than the default.
Conflicts:
doc/openocd.texi
src/flash/nor/fespi.c
src/jtag/drivers/libjaylink
src/rtos/rtos.c
src/target/riscv/batch.c
src/target/riscv/encoding.h
src/target/riscv/riscv-011.c
src/target/riscv/riscv-013.c
src/target/riscv/riscv.c
src/target/riscv/riscv.h
src/target/target.c
tcl/target/gd32vf103.cfg
Change-Id: I1321f62ba719419e58f93b2195f2540bd62f50d2
Antonio Borneo
asier70
Tim Newsome
Tarek BOCHKATI
Andreas Sandberg
Marc Schink
Wealian Liao
Robbert
Oleksij Rempel
Ranjith Chandran
Jian-Hong Pan
Matthew Mets
Patrick Stewart
Andreas Fritiofson
Florian Fainelli
Marek Vasut
Rohit Singh
micbis
Olivier DANET
Peter Lawrence
Leonard Crestez
Andrew Wesie
Felipe Balbi
Jiri Kastner
Anthony Ferranti
Nishanth Menon
Kevin Mills
Tarek BOCHKATI
Andreas Bolsch
Alberto García Hierro
Jonathan McDowell
Karl Palsson
Diego Herranz
John Pham
Tomas Vanek