Tested on an EFM32PG12 Starter Kit.
Change-Id: I2cbc36fe0d2ad2089bf8c1e7d2260daaae4ddbb4
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/5353
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace deprecated commands 'mem2array' and 'array2mem' with
new Tcl commands 'read_memory' and 'write_memory'.
Change-Id: I116d995995396133ca782b14cce02bd1ab917a4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6859
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the LS1046A Reference Design Board. There are
several JTAG headers accessable once the case is opened, but this config
is for the externally-accessable CMSIS DAP.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I0f83470da3758f0c4512ce47348c4db7de17b27e
Reviewed-on: https://review.openocd.org/c/openocd/+/6855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1046A is a quad-core processor from NXP in the layerscape family.
This SoC is a bit tricky to program: while the AArch64 CPUs are
little-endian, most of the peripherals are big-endian. Care must be
taken when interpreting memory reads/writes. This processor is in the
same family as the ls1012a, so the setup is similar.
If you use OpenOCD to attach early in the boot process, only the cpu0
may be available. Trying to halt other CPUs will fail. To avoid this,
defer examination of cpus 1-3, and provide a core_up helper (like e.g.
zynqmp).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: If5a1a9441fb35fea3e05dc708b42e0cb3bbf2a54
Reviewed-on: https://review.openocd.org/c/openocd/+/6854
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Original TLC syntax uses 'set varname' to retrieve the value of
variable 'varname'. Such archaic syntax is still valid, but the
shorter '$varname' makes the code easier to read.
Replace 'set varname' with '$varname'.
While there, remove some useless curly brackets.
Change-Id: I27310e8c05afe56ea8bd0e41d4ae2c34447b725c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6863
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add support for the latest in TI k3 family AM625 SoC.
For further details, see https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: Ia54d0eab1c30a973afb1c2c61f4c5a72d29d9b78
Reviewed-on: https://review.openocd.org/c/openocd/+/6798
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the latest in TI k3 family J721S2 SoC.
For further details, see http://www.ti.com/lit/pdf/spruj28
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I608ab4513ffb6b5c4166ba423e7d0dddbbb3bbfd
Reviewed-on: https://review.openocd.org/c/openocd/+/6796
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since we can detect the type of target as well, reuse the _cpu_no_smp_up
function name and use the target name to simplify the _up function and
maintain consistency with what we introduced for r5.
Lets introduce gdb-attach event in a much cleaner fashion.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
While at it, fix a minor type of s/are/as in "Set Default target are
core 0" and simplify the foreach usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3259b7c3ae4c71b06d921edfaefe17c03bb673dc
Reviewed-on: https://review.openocd.org/c/openocd/+/6616
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Since we can detect the type of target as well, make the attach
function name generic for the follow on cleanup patch on armv8 to use
as well.
Lets introduce gdb-attach event in a much cleaner fashion. We can
introduce a simpler r5_up function since we now have more descriptive
core names making the individual descriptive procs redundant.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I31506bb2b86e63638082640eb72aa7c4c9575e93
Reviewed-on: https://review.openocd.org/c/openocd/+/6617
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
R5 targets are currently named r5.0..n and the only way for user to
determine the actual type is external documentation. Lets just rename
the target names to make them descriptive to not require external
documentation for finding which R5 to connect to.
NOTE: we leave the _mcu_r5_cores _main0_r5_cores _main1_r5_cores alone
for now to allow existing startup proc functions to work, but we will
drop it in the follow on patch.
Previously:
Info : starting gdb server for j721e.cpu.r5.0 on 3336
Info : Listening on port 3336 for gdb connections
Info : starting gdb server for j721e.cpu.r5.1 on 3337
Info : Listening on port 3337 for gdb connections
Info : starting gdb server for j721e.cpu.r5.2 on 3338
Info : Listening on port 3338 for gdb connections
Info : starting gdb server for j721e.cpu.r5.3 on 3339
Info : Listening on port 3339 for gdb connections
Info : starting gdb server for j721e.cpu.r5.4 on 3340
Info : Listening on port 3340 for gdb connections
Info : starting gdb server for j721e.cpu.r5.5 on 3341
Info : Listening on port 3341 for gdb connections
With this patch:
Info : starting gdb server for j721e.cpu.mcu_r5.0 on 3336
Info : Listening on port 3336 for gdb connections
Info : starting gdb server for j721e.cpu.mcu_r5.1 on 3337
Info : Listening on port 3337 for gdb connections
Info : starting gdb server for j721e.cpu.main0_r5.0 on 3338
Info : Listening on port 3338 for gdb connections
Info : starting gdb server for j721e.cpu.main0_r5.1 on 3339
Info : Listening on port 3339 for gdb connections
Info : starting gdb server for j721e.cpu.main1_r5.0 on 3340
Info : Listening on port 3340 for gdb connections
Info : starting gdb server for j721e.cpu.main1_r5.1 on 3341
Info : Listening on port 3341 for gdb connections
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2989efe3ae3e16754f98fa1dc9363ec4c898f7c3
Reviewed-on: https://review.openocd.org/c/openocd/+/6627
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The MCU is present on few of the SoCs and is meant as General Purpose
(GP) MCU of the system. Lets rename it to make clear what we are
debugging - esp when multiple MCUs are present in the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I16132d321daf6e9b1d893fe6f92026d5aa9eb152
Reviewed-on: https://review.openocd.org/c/openocd/+/6619
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The M3 is the system controller of the system. Lets rename it to make
clear what we are debugging - esp when multiple MCUs are present in the
system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I4cd03b6068b8ce140fd254f9dd88151c4c7006d7
Reviewed-on: https://review.openocd.org/c/openocd/+/6618
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add gdb-attach event to call the "up" function of m3 and m4 allowing for
more seamless integration with gdb for end users. We still retain _up
functions for non-gdb functionality.
NOTE: we add a halt 1000 to retain the default gdb-attach hook behavior
Suggested-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I2e51fdbd8756f156551e589c748c3a338afa655c
Reviewed-on: https://review.openocd.org/c/openocd/+/6615
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
both stm32l5x and stm32u5x configs are almost identical except
clock config.
while at there rename target procs to avoid issues with JTAG daisy
chaining.
Change-Id: Ibbb1dfeb91a7f8d5d45744cf57dca2877f60e0c5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6596
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* flash/nor/atsame5: add LAN9255 devices
Support Microchip LAN9255 devices with embedded SAME53J MCU.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Change-Id: Ia811c593bf7cf73e588d32873c68eb67c6fafad7
Reviewed-on: https://review.openocd.org/c/openocd/+/6811
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl/board: Add EVB-LAN9255 config
Config for EVB-LAN9255, tested using Atmel-ICE debugger on J10
connector.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Change-Id: I8bcf779e9363499a98aa0b7d10819c53da6a19e7
Reviewed-on: https://review.openocd.org/c/openocd/+/6812
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* aarch64: support for aarch32 ARM_MODE_UND
Fix:
unrecognized psr mode: 0x1b
cannot read system control register in this mode: (UNRECOGNIZED : 0x1b)
Change-Id: I4dc3e72f90d57e52c0fe63cb59a7529a398757b3
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Change-Id: Ifa5d21ae97492fde9e8c79ee7d99d8a2a871b1b5
Reviewed-on: https://review.openocd.org/c/openocd/+/6808
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Combine register lists of smp targets.
This is helpful when you want to pretend to gdb that your heterogeneous
multicore system is homogeneous, because gdb cannot handle heterogeneous
systems. This won't always works, but works fine if e.g. one of the
cores has an FPU while the other does not. (Specifically, HiFive
Unleashed has 1 core with no FPU, plus 4 cores with an FPU.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I05ff4c28646778fbc00327bc510be064bfe6c9f0
Reviewed-on: https://review.openocd.org/c/openocd/+/6362
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* semihosting: use open mode flags from GDB, not from sys/stat.h
Values defined in sys/stat.h are not guaranteed to match
the constants defined by the GDB remote protocol, which are defined in
https://sourceware.org/gdb/onlinedocs/gdb/Open-Flags.html#Open-Flags.
On my local system (Manjaro 21.2.1 x86_64), for example, O_TRUNC is
defined as 0x40, whereas GDB requires it to be 0x400,
causing all "w" file open modes to misbehave.
This patch has been tested with STM32F446.
Change-Id: Ifb2c740fd689e71d6f1a4bde1edaecd76fdca910
Signed-off-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* semihosting: User defined operation, Tcl command exec on host
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/smp: use a struct list_head to hold the smp targets
Instead of reinventing a simply linked list, reuse the list helper
for the list of targets in a smp cluster.
Using the existing helper, that implements a double linked list,
makes trivial going through the list in reverse order.
Change-Id: Ib36ad2955f15cd2a601b0b9e36ca6d948b12d00f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6783
Tested-by: jenkins
* helper/list: add list_for_each_entry_direction()
Use a bool flag to specify if the list should be forward or
backward iterated.
Change-Id: Ied19d049f46cdcb7f50137d459cc7c02014526bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6784
Tested-by: jenkins
* target/riscv: revive 'riscv resume_order'
This functionality was lost in [1], which was merged as commit
615709d140 ("Upstream a whole host of RISC-V changes.").
Now it works as expected again.
Add convenience macro foreach_smp_target_direction().
Link: [1] https://github.com/riscv/riscv-openocd/pull/567
Change-Id: I1545fa6b45b8a07e27c8ff9dcdcfa2fc4f950cd1
Signed-off-by: Tim Newsome <tim@sifive.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6785
Tested-by: jenkins
* doxygen: fix some function prototype description
Change-Id: I49311a643ea73143839d2f6bde976cfd76f8c67f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6830
Tested-by: jenkins
* Cadence virtual debug interface (vdebug) integration
Change-Id: I1bc105b3addc3f34161c2356c482ff3011e3f2cc
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6097
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: Include thread name as XML attribute
Explicitly providing a thread name in the "thread" element produces
better thread visualizations in downstream tools like IDEs.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I102c14ddb8b87757fa474de8e3a3f6a1cfe10d98
Reviewed-on: https://review.openocd.org/c/openocd/+/6828
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix small memory leak.
See https://github.com/riscv/riscv-openocd/pull/672
Change-Id: Ia11ab9bcf860f770ea64ad867102c74b898f6b66
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6831
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* server: remove remaining crust from dropped eCos code
Commit 39650e2273 ("ecosboard: delete bit-rotted eCos code") has
removed eCos code but has left some empty function that was used
during non-eCos build to replace eCos mutex.
Drop the functions and the file that contain them.
Change-Id: I31bc0237ea699c11bd70921660f960ee406ffa80
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6835
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: threadx: Add hla_target support for ThreadX
Tested with an AZ3166 dev board (which uses the STM32F412ZGT6) running
the Azure RTOS ThreadX demonstration system.
Signed-off-by: Ben McMorran <bemcmorr@microsoft.com>
Change-Id: I44c8f7701d9f1aaa872274166321cd7d34fb1855
Reviewed-on: https://review.openocd.org/c/openocd/+/6829
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* .gitmodules: switch away from repo.or.cz
The host repo.or.cz is often offline, creating issues for cloning
and building OpenOCD from scratch.
Already 'jimtcl' developer has dropped repo.or.cz, triggering the
OpenOCD commit 861e75f54e ("jimtcl: switch to github").
Change also the link of the remaining submodules 'git2cl' and
'libjaylink' to their respective main repository.
Change-Id: Ib513237427635359ce36a480a8f2060e2fb12ba4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6834
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
* flash/nor/stm32f2x: Fix erase of bank 2 sectors
This commit corrects the erase function for stm32f2x when dealing with
sectors in bank 2, for STM32F42x/43x devices with 1MB flash.
On STM32F42x/43x with 1MB flash in dual bank configuration, the sector
numbering is not consecutive. The last sector in bank 1 is number 7, and
the first sector in bank 2 is number 12.
The sector indices used by openocd, however, _are_ consecutive (0 to 15
in this case). The arguments "first" and "last" to stm32x_erase() are of
this type, and so the logic surrounding sector numbers needed to be
corrected.
Since the two banks in dual bank mode have the same number of sectors, a
sector index in bank 2 is larger than or equal to half the total number
of sectors.
Change-Id: I15260f8a86d9002769a1ae1c40ebdf62142dae18
Signed-off-by: Simon Johansson <ampleyfly@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6810
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* target/cortex_m: fix target_to_cm() helper
The third parameter of container_of() should point to the same member
as target->arch_info points to, struct arm.
It worked just because struct arm is the first member in
struct armv7m_common.
If you move arm member from the first place, OpenOCD fails heavily.
Change-Id: I0c0a5221490945563e17a0a34d99a603f1d6c2ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6749
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/armv7m,cortex_m: introduce checked arch_info cast routines
target_to_armv7m() and target_to_cm() do not match the magic number
so they are not suitable for use outside of target driver code.
Add checked versions of pointer getters. Match the magic number
to ensure the returned value points to struct of the correct type.
Change-Id: If90ef7e969ef04f0f2103e0da29dcbe8e1ac1c0d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6750
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/cortex_m: add Cortex-M part number getter
The getter checks the magic numbers in arch_info to detect eventual
type mismatch.
Change-Id: I61134b05310a97ae9831517d0516c7b4240d35a5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6751
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* flash/nor/stm32xx: fix segfault accessing Cortex-M part number
Some of STM32 flash drivers read Cortex-M part number from
cortex_m->core_info.
In corner cases the core_info pointer was observed uninitialised
even if target_was_examined() returned true. See also [1]
Use the new and safe helper to get Cortex-M part number.
While on it switch also target_to_cm()/target_to_armv7m() to the safe
versions. This prevents a crash when the flash bank is misconfigured
with non-Cortex-M target.
Add missing checks for target_was_examined() to flash probes.
[1] 6545: fix crash in case cortex_m->core_info is not set
https://review.openocd.org/c/openocd/+/6545
Change-Id: If2471af74ebfe22f14442f48ae109b2e1bb5fa3b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: f5898bd93f (flash/stm32fxx.c: do not read CPUID as this info is stored in cortex_m_common)
Reviewed-on: https://review.openocd.org/c/openocd/+/6752
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* cpld: altera-epm240: Add additional IDCODEs
This adds some additional IDCODEs from the datasheet. It also adds
support for customizing the tap name.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I7cda10b92c229b61836c12cd9ca410de358ede2e
Reviewed-on: https://review.openocd.org/c/openocd/+/6846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cpld: altera-epm240: Increase adapter speed
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: Add support for ls1088a
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: ls1088a: Add service processor
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* board: Add NXP LS1088ARDB
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: fix double free
Commit 6541233aa7 ("Combine register lists of smp targets.")
unconditionally assigns the output pointers of the function
smp_reg_list_noread(), even if the function fails and returns
error.
This causes a double free from the caller, that has assigned NULL
to the pointers to simplify the error handling.
Use local variables in smp_reg_list_noread() and assign the output
pointers only on success.
Change-Id: Ic0fd2f26520566cf322f0190780e15637c01cfae
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6852
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* gdb_server: check target examined while combining reg list
Commit 6541233aa7 ("Combine register lists of smp targets.")
assumes that all the targets in the SMP cluster are already
examined and unconditionally call target_get_gdb_reg_list_noread()
that will in turn return error if the target is not examined yet.
Skip targets not examined yet.
Add an additional check in case the register list cannot be built,
e.g. because no target in the SMP cluster is examined. This should
never happen, but it's better to play safe.
Change-Id: I8609815c3d5144790fb05a870cb0c931540aef8a
Fixes: 6541233aa7 ("Combine register lists of smp targets.")
Reported-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6853
Tested-by: jenkins
Reviewed-by: Michele Bisogno <michele.bisogno.ct@renesas.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* flash/stm32l4x: fix maybe-uninitialized compiler error
using gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0 we get:
error: ‘retval’ may be used uninitialized in this function
fixes: 13cd75b6ec (flash/nor/stm32xx: fix segfault accessing Cortex-M part number)
Change-Id: I897c40c5d2233f50a5385d251ebfa536023e5cf7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix build.
Change-Id: Ia60246246dd859d75659a43d1c59588dbb274d46
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Co-authored-by: Julien Massot <julien.massot@iot.bzh>
Co-authored-by: Pavel Kirienko <pavel.kirienko@gmail.com>
Co-authored-by: Zoltán Dudás <zedudi@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Jacek Wuwer <jacekmw8@gmail.com>
Co-authored-by: Ben McMorran <bemcmorr@microsoft.com>
Co-authored-by: Simon Johansson <ampleyfly@gmail.com>
Co-authored-by: Tomas Vanek <vanekt@fbl.cz>
Co-authored-by: Sean Anderson <sean.anderson@seco.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Normally the service processor is not necessary for debugging. However,
if you are using the hard-coded RCW or your boot source is otherwise
corrupt, then the general purpose processors will never be released from
hold-off. This will cause GDB to become confused if it tries to attach,
since they will appear to be running arm32 processors. To deal with
this, we can release the CPUs manually with the BRRL register. This
register cannot be written to from the axi target, so we need to do it
from the service processor target. This involves halting the service
processor, modifying the register, and then resuming it again. We try
and determine what state the service processor was in to avoid resuming
it if it was already halted.
The reset vector for the general purpose processors is determined by the
boot logation pointer registers in the device configuration unit.
Normally these are set using pre-boot initialization commands, but if
they are not set then they default to 0. This will cause the CPU to
almost immediately hit an illegal instruction. This is fine because we
will almost certainly want to attach to the processor and load a program
anyway.
I considered adding this as an event handler for either gdb-attach or
reset-init. However, this command shouldn't be necessary most of the
time, and so I don't think we should run it automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I1b725292d8a11274d03af5313dc83678e10e944c
Reviewed-on: https://review.openocd.org/c/openocd/+/6850
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The LS1088A is an octo-core aarch64 processor from NXP in the layerscape
family. The JTAG is undocumented, but I was able to figure things out
from the output of `dap info`. This is the first in-tree example of
using the hwthread rtos (as far as I know), so hopefully it can serve as
an example to other developers. There are some ETMs, but I was unable to
try them out because I got 'invalid command name "etm"' when trying to
test things out.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9b0791d27d8c41170a413a8d86431107a85feba2
Reviewed-on: https://review.openocd.org/c/openocd/+/6848
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, the minimum clock period with Vccio1 = 1.5V
(the lowest voltage supported) is 143ns, or around 6MHz. Set the default
adapter speed to 5 MHz.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I21cad33fa7f1e25e81f43b5d2214d1fa4ec924de
Reviewed-on: https://review.openocd.org/c/openocd/+/6847
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds some additional IDCODEs from the datasheet. It also adds
support for customizing the tap name.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I7cda10b92c229b61836c12cd9ca410de358ede2e
Reviewed-on: https://review.openocd.org/c/openocd/+/6846
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Changed flash driver to support writing to the user data page, as well as to any portion of the lockbits page above 512 bytes (the amount used for the actual page lock words). The top part of the lockbits page is used on at least the EFR32xG1 chips for the SiLabs bootloader encryption keys.
As presented to the user, the lockbits page is the same size as the other pages, but any attempt to write to its low 512 bytes is an error. To enforce this, efr32x_write is renamed to efm32x_priv_write and a wrapper function is provided in its place. If the user erases the lockbits page, the driver rewrites the cached lock words after the erase. When the driver erases the lockbits page in order to update the lock words, it first takes a copy of anything stored in the top part of the page, and re-programs it after the erase operation.
There are now multiple instances of flash_bank for each target, and the flash_bank instances must share their cached lock words to operate as intended. Therefore, when a bank is created, the global flash bank list is used to find any other banks that share the same target. Since some banks in the global list are invalid at the time free_driver_priv is called, reference counting is used to decide when to free driver_priv.
To avoid the need to find the lockbits flash_bank from another flash_bank, efm32x_priv_write and efm32x_erase_page now take an absolute address.
There didn't seem to be any reason to prohibit unprotecting individual flash pages, so that limitation is removed from efm32x_protect().
This addresses ticket #185.
Valgrind-clean, except for 2x 4kiB not freed/still reachable blocks that were allocated by libudev.
No new Clang analyzer warnings, no new sanitizer warnings.
Signed-off-by: Doug Brunner <doug.a.brunner@gmail.com>
Change-Id: Ifb22e6149939d893f386706e99b928691ec1d41b
Reviewed-on: https://review.openocd.org/c/openocd/+/6665
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Also rename ftdi_oscan1_mode command which only exists in our branch.
Change-Id: Ie9b28f228b1fd984244edb8162d552104d28e462
Signed-off-by: Tim Newsome <tim@sifive.com>
This board is (software wise) similar to the existing SAME54 Xplained
Pro board, with just a slightly different MCU. (Hardware wise, it
features a vastly different form factor.)
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Change-Id: I5e5435d49d333fb74471994ee84de59ed983153c
Reviewed-on: https://review.openocd.org/c/openocd/+/6747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Axel W.
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32mp13x has one core Cortex-A7.
The board Discovery Kit includes an on-board STLink-V3 with SWD
connection.
The webpage of the board is not active yet.
Change-Id: I8836b26612a160ead79766955ebefaf3d21a329c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6675
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
The driver jlink defines the command 'jlink serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: in former code the commands 'jlink serial' and 'jlink usb'
were mutually exclusive; running one of them would invalidate the
effect of a previous execution of the other. The new code gives
priority to 'adapter serial', even if executed before 'jlink usb'.
Change-Id: I920b0c136716f459b6fd6f7da8a01a7fa1ed389f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6656
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The driver xds110 defines the command 'xds110 serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Note: the original command 'xds110 serial' used a complex and
undocumented conversion of the serial number through multibyte
string, wide-character string and C cast. The XDS110 I can access
and the lsusb dumps available through Google don't show any
exotic USB serial that require such conversion. The original
developer doesn't remember any constraint that mandates such
conversion (see comments in https://review.openocd.org/4322/).
The conversion is removed by this patch.
Change-Id: I38909918079b2c1797ad85ebec2fea1b33743606
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6655
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver kitprog defines the command 'kitprog_serial' to specify
the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I844cb815af01137392b6d12e1b5972fc77ac092d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6652
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The driver ftdi defines the command 'ftdi serial' to specify the
serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: Ia5b1f325b9fab8f58b5ea70f8b807e50b148b939
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6651
Tested-by: jenkins
The driver cmsis_dap defines the command 'cmsis_dap_serial' to
specify the serial string of the adapter.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I88e2d4de360a6c6f23529bb18494962a267250df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6649
Tested-by: jenkins
The driver aice defines the command 'aice serial' to specify the
serial string of the adapter, but actually does not use this value
in the code.
Remove and deprecate the driver command, and use 'adapter serial'.
Change-Id: I892e0a4e1b41a7a87adf54a5736abf7419f32979
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6648
Tested-by: jenkins
GD32E23x from GigaDevice is cortex-M23 microcontroller and it can work with the stm32f1x driver.
Modifications are similar to this done for GD32F1x0 in #6164 (https://review.openocd.org/c/openocd/+/6164).
Configuration file is added because its cortex-M23 CPU ID is different.
I think that GigaDevice microcontrollers should be handled in an independent unit to separate them from STM32,
but nowadays quick solution is welcome.
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Change-Id: I91f31f5f66808bc50a8f607ac2c107e6b7c5e2b8
Reviewed-on: https://review.openocd.org/c/openocd/+/6527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This primarily contains the large upstreaming of RISC-V changes, so lots
more RISC-V changes than usual.
Conflicts:
src/target/riscv/opcodes.h
src/target/riscv/riscv-011.c
src/target/riscv/riscv-013.c
src/target/riscv/riscv.c
src/target/riscv/riscv.h
Change-Id: I1145dad538a5470ad209848572e6b0f560b671e9
Signed-off-by: Tim Newsome <tim@sifive.com>
Freeze the IWDG watchdog when cores are halted to prevent a reset
while debugging.
The PMIC present on some board senses the nsrst and forces a power
cycle to the target. The power cycle causes the SWJ-DP to restart
in JTAG mode. If the debugger is using SWD, the mismatch triggers
an error after the reset command.
Ignore the error detected by 'dap init' and proceed executing the
handler. The error in 'dap init' will force a reconnect during the
following 'dap apid', restoring the SWD functionality.
Change-Id: I04fcda6a5b8a1b080ab4e8890ecd0754d5ed12d9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6599
Tested-by: jenkins
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
do not force the presence of the reset line, since some custom boards
may do not contain the reset line.
Change-Id: I031ab34012b34a1b49def9db16461f9de0ae29cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Fleck <fleckz@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/316/
Reviewed-on: https://review.openocd.org/c/openocd/+/6506
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
known boards are NUCLEO-G431KB, NUCLEO-G431RB and NUCLEO-G474RE
note: this work safely with B-G431B-ESC1, B-G474E-DPOW1,
STM32G474E-EVAL and STM32G484E-EVAL
Change-Id: I132a97e1816620b182983edc8a4b272b52b9241d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5484
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G031K8, NUCLEO-G070RB, NUCLEO-G071RB
note: this work safely with STM32G0316-DISCO, STM32G071B-DISCO
and STM32G081B-EVAL
Change-Id: I483b6f44409228cd8c2c97b3c560927d1645c517
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5483
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
After compiling OpenOCD from source (commit: 6edf98db7), OpenOCD could not connect with the target board which is a GD32VF103T_START development board,
when I used the command: openocd -f "interface/cmsis-dap.cfg" -f "target/gd32vf103.cfg"
Issue 1: The clock speed hasn't been set, the error message given is:
Error: CMSIS-DAP command CMD_DAP_SWJ_CLOCK failed.
Which can be solved by adding a clock speed setting to the gd32vf103.cfg file:
adapter speed 1000
Issue 2: The default transport is not set to jtag, which it requires, the error shown is:
Open On-Chip Debugger 0.11.0+dev-01861-g6edf98db7-dirty (2021-08-25-10:18)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "swd". To override use 'transport select <transport>'.
embedded:startup.tcl:128: Error: session transport is "swd" but your config requires JTAG
in procedure 'script'
at file "embedded:startup.tcl", line 26
in procedure 'jtag' called at file "/home/user/riscv-openocd-tool/usr/local/bin/../share/openocd/scripts/target/gd32vf103.cfg", line 9
in procedure 'default_to_jtag' called at file "embedded:startup.tcl", line 133
at file "embedded:startup.tcl", line 128
This issue can be solved by adding the line:
transport select jtag
After adding these two lines, OpenOCD could connect to the development board successfully. Programming the flash also works.
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for ECP5 FPGA targets and board based on this chips:
Radiona ULX3S and Lambdaconcept ECPIX-5
Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6112
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The V3U SoC is unique in that it now has 8x CA76 and CR52,
while the previous SoCs had CA57/CA53/CR7 . This can still
be handled without too complex modifications to the gen3
configuration file, so add the logic to handle it there.
Change-Id: I7ab33eacc1fd379d369988d3d6690d2e82346c7e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On SMP Renesas R-Car Gen2/Gen3 systems, select the boot core as
the default target using the 'targets' command. This way, the
user can start debugging code running on the boot core without
having to switch to the boot core by explicitly invoking 'targets'
command first, since it is likely the debugged code will run on
the boot core. Note that most of the code is already in place, it
was just not used, so this is more of a fix to make the original
intention work.
Change-Id: I727808adce617c1d9ebd6ffa34f60f5882cdae60
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6313
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: use unsigned int for FPB and DWT quantifiers
related quantifiers are:
- fp_num_lit
- fp_num_code
- dwt_num_comp
- dwt_comp_available
Change-Id: I07dec2d4aa21bc0e580be0d9fd0a6809f876c2a8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6185
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* telnet: allow hiding selected commands during auto-completion
We have TCL procedure and commands that we do not want to show in
the list of auto-completion. E.g. TCL wrappers for deprecated
commands, internal procedures that are not supposed to be exposed
to user, or even commands that the user decides to hide.
Create a TCL procedure to be called by telnet auto-complete code
in place of the hard-coded TCL command. The procedure will run the
same command and will filter-out the unwanted command names.
Initialize the list of commands to be filtered-out with the name
of the TCL procedure above, as it is considered as internal.
Change-Id: I2d83bbf8194502368c589c85cccb617e69128c69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6194
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* telnet/auto-complete: hide deprecated and internal commands
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* startup.tcl: prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Modify the script startup.tcl compiled-in OpenOCD binary to comply
with the new jimtcl.
Change-Id: I520dcafacadaa289a815035f93f250447ca66ea0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6158
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl: [1/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* tcl: [2/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
* tcl: [3/3] prepare for jimtcl 0.81 'expr' syntax change
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* target/stm8: Make 'stm8_command_handlers' static
Change-Id: I5237a8f2a1ecba9383672e37bd56f8ccd17598b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6200
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/riscv: Change 'authdata_read' output
Use a constant output length and remove the line break to make the
authentication data easier to parse.
Change-Id: Iebbf1f171947ef89b0f360a2cb286a4ea15c6ba5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6199
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* Enable adapter "Bus Pirate" by default.
The Bus Pirate is now listed in the "OpenOCD configuration summary" too.
Change-Id: Ieb7bf9134af456ebe9803f3108a243204fb2a62d
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/5637
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* coding-style: additional style for C code
To improve readability and to push more uniform code style.
Prefer 'if (false) {...}' for unused code so it get checked by the
compiler.
Define preferred indentation for 'switch' statement.
Require balanced brackets in 'if/else'.
Report the max line length.
Report the formatting strings for stdint/inttypes types.
Report the type 'target_addr_t'.
Prefer 'unsigned int' to 'unsigned'.
Change-Id: I0192a4ed298f6c6c432764fdd156cffd4b13fc89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6203
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
* Add IPDBG JtagHost functionality to OpenOCD
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* flash/nor/xcf: Do not use 'Yoda conditions'
Change-Id: I17308f5237338ce468e5b86289a0634429deaaa9
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6201
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cortex_m: add armv8m special registers
Change-Id: I1942f375a5f4282ad1fe4a2ff3b8f3cbc64d8f7f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6016
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* rtos: Add support for Zephyr RTOS
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/armv7m.h: [style] replace tab with space between variable type and name
Change-Id: I9740c25857295a2a655d3046322a3f23f0ee7f78
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6230
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* server: gdb_server: Add colon for target extended-remote
Both GDB commands "target remote" and "target extended-remote" require
to have ":" right before port number.
e.g.
(gdb) target extended-remote :3333
Add ":" to the warning message so that users can copy & past it.
Change-Id: Id6d8ec1e4dfd3c12cb7f3b314064f2c35fa7ab55
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6237
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* jimtcl: restrict memory leak workaround on Linux only
The workaround for jimtcl 0.80 in commit 36ae487ed0 ("jimtcl:
add temporary workaround for memory leak in jimtcl 0.80") issues a
compile time error on macOS:
../src/helper/command.c:157:22: error: aliases are not
supported on darwin
__attribute__((weak, alias("workaround_createcommand")));
The OS is x86_64-apple-darwin19.6.0 and the compiler used is
x86_64-apple-darwin13.4.0-clang.
Restrict the workaround on Linux host only. The fix for 'expr'
syntax change is already merged and the workaround will be dropped
soon.
Change-Id: I925109a9c57c05f8c95b70bc7d6604eb1172cd79
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adam Jeliński <ajelinski@users.sourceforge.net>
Fixes: 36ae487ed0 ("jimtcl: add temporary workaround for memory leak in jimtcl 0.80")
Fixes: https://sourceforge.net/p/openocd/tickets/304/
Reviewed-on: http://openocd.zylin.com/6241
Tested-by: jenkins
* target/armv7m: fix static analyzer warning
Despite of assert(is_packed) clang static analyser complains on use
of the uninitialized offset variable.
Cross compiling with latest x86_64-w64-mingw32-gcc hits warnings
src/target/armv7m.c: In function ‘armv7m_read_core_reg’:
src/target/armv7m.c:337:54: error: ‘reg32_id’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
It happens because mingw32 defines assert() without the attribute
"noreturn", whatever NDEBUG is defined or not.
Replace assert(is_packed) by if (is_packed) conditional and call
assert(false) in the else branch.
Change-Id: Id3c7dcccb65106e28be200b9a4d2b642f4d31019
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6256
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
* cmsis_dap: fix build on macOS
Compile fails with error:
src/jtag/drivers/cmsis_dap.c:683:28: error: format specifies type
'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
" received 0x%" PRIx8, CMD_DAP_TFER, resp[0]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
Fix the format specifier.
Change-Id: I0a5a1a35452d634019989d14d849501fb8a7e93a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6255
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* cortex_m: do not perform soft_reset_halt on targets without VECTRESET
Change-Id: Ib3df457e0afe4e342c82ad1af25e03aad6979d87
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6209
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* cortex_m: fix VECTRESET detection for ARMv6-M cores
VECTRESET check should be done after verifying if the core is an ARMv6-M core,
and not before that.
Fixes: 2dc9c1df81 ("cortex_m: [FIX] ARMv8-M does not support VECTRESET")
Change-Id: I8306affd332b3a35cea69bba39ef24ca71244273
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6232
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/arm_dpm: rename 'wp_pc' as 'wp_addr'
The field 'wp_pc' was originally introduced in commit 55eeea7fce
("ARMv7a/Cortex-A8: report watchpoint trigger insn") in end 2009
to contain the address of the instruction which triggered a
watchpoint. Later on with commit 651b861d5d ("target/aarch64:
Add watchpoint support") it has been reused in to hold directly
the memory address that triggered a watchpoint.
Rename 'wp_pc' as 'wp_addr' and change its doxygen description.
While there, fix the format string to print the field.
Change-Id: I2e5ced1497e4a6fb6b38f91e881807512e8d8c47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6204
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
* target/aarch64: fix watchpoint management
The early documentation for armv8a report the debug register WFAR
as containing the address of the instruction that triggered the
watchpoint. More recent documentation report the register EDWAR as
containing the data memory address that triggered the watchpoint.
The name of macros CPUV8_DBG_WFAR0 and CPUV8_DBG_WFAR1 is not
correct as they point to the debug register EDWAR, so reading such
register returns directly the data memory address that triggered
the watchpoint. The code incorrectly passes this address value to
the function armv8_dpm_report_wfar(); this function is supposed to
adjust the PC value, decrementing it to remove the effects of the
CPU pipeline. This pipeline offset, that has no meaning on the
value in EDWAR, caused commit 651b861d5d ("target/aarch64: Add
watchpoint support") to add back the offset while comparing the
address with the watchpoint enabled.
The upper 32 bits of EDWAR are not valid in aarch32 mode and have
to be ignored.
Rename CPUV8_DBG_WFAR0/1 as CPUV8_DBG_EDWAR0/1.
Remove the function armv8_dpm_report_wfar().
Remove the offset while searching the matching watchpoint.
Ignore the upper 32 bits of EDWAR in aarch32 mode.
Fix a comment and the LOG text.
Change-Id: I7cbdbeb766fa18e31cc72be098ca2bc501877ed1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6205
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
* flash/stm32l4x: add missing break statement
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
* github/action: create a permanent 'latest' release
this commit extends the existing snapshot action to create a release named
'latest' with the built binaries for windows.
this 'latest' release will be updated after every push to github.
Change-Id: I75a64c598169241743add3ac9aa7a0337fbab7f2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6127
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* tcl/rp2040: remove empty line at end of file
Change-Id: I212a96b77282b151a8ecbd46a6436e2bbbda4161
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6221
Tested-by: jenkins
* tcl: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
* flash: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
* jtag: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I101c76a638805d77c1ff356cf0f027552389e5d3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6216
Tested-by: jenkins
* target: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
* openocd: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
* Document the buspirate interface driver.
Change-Id: Iaff13fc5187041a840f4f00eb6b4ee52880cf47e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6231
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Warn on undefined preprocessor symbols
Preprocessor directives like "#if SYMBOL" silently replace undefined or
misspelt symbols with 0, which makes configuration bugs hard to spot.
Compiler flag "-Wundef" prevents such errors.
Change-Id: I91b7ba2db02ef0c3c452d334601c53aebda4660e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6238
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Remove compatibility macros m4_ifblank and m4_ifnblank
They are at least since Autoconf 2.67 present,
and we are requiring version 2.69.
Change-Id: I41b33d4ebe02198f03cdddcc4a3c1beedd993d78
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* configure.ac: use a separate folder for Autoconf-generated files
Autoconf generates several files in root folder of the project.
Keep the root folder cleaner by specifying subfolder 'build-aux'.
Align .gitignore accordingly.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: Ied87faba495d9eeb8f98e78c2e2b7e7e596febfb
Reviewed-on: http://openocd.zylin.com/6236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* helper/command: silent debug msg on command register/unregister
Commit e216186fab ("helper/command: register full-name commands
in jim") and commit a7d68878e4 ("helper/command: unregister
commands through their full-name") introduce a LOG_DEBUG() message
each for command registration and unregistration.
The messages above are quite noisy and pollute the log when
debug_level is 3 or higher.
They can be useful to debug the command registration logic, but
for the other debug activities on OpenOCD are just noisy.
Already commit a03ac1ba30 ("helper/command: disable logging of
registered commands [RFC]") was merged to silent the first case
that is now back with additional logs.
Silent both log messages.
Use 'if (false)' to silent them, making easy to re-enable it when
or if someone needs it.
Change-Id: Id8a067e60e822d4ecbddcb036d081298f7e6181f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6220
Tested-by: jenkins
* mem_ap: fix target arch_info type
The target mem_ap appears as an ARM target, thus it allows the
execution of ARM specific commands causing the crash of OpenOCD.
E.g. 'arm mrc ...' can be executed and segfaults.
Replace the incorrect ARM magic number with a dedicated one.
While there, remove the 'struct arm', that is now holding only the
mem_ap's dap, and replace it with a pointer to the dap.
Change-Id: I881332d3fdf8d8f8271b8711607737b052a5699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6213
Tested-by: jenkins
* riscv: drop unused variable
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
* riscv: replace macro DIM() with ARRAY_SIZE()
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* target/zynqmp : Add AXI AP access port
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* drivers/versaloon: use ARRAY_SIZE()
Replace the custom macro dimof() with the OpenOCD macro
ARRAY_SIZE().
Change-Id: I2fe638444f6c16f2a78c1fd558b21550f76282d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6259
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
* openocd: use macro ARRAY_SIZE()
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
* rtos: use ARRAY_SIZE() and simplify rtos_type.create()
Use the existing macro ARRAY_SIZE().
Rewrite the functions rtos_type.create() to simplify the logic.
Change-Id: I8833354767045d1642801d26944c9087a77add00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6261
Tested-by: jenkins
* tcl: remove remaining deprecated commands
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
* help text: remove trailing space
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
* help: fix line size in 'usage' output
The implementation of command 'usage' is broken while checking the
line limit of 76 chars per line (e.g. 'usage load_image') and the
line wrapping is not correct. The same broken code is used for the
first output line of command 'help' too.
When call command_help_show_wrap(), include the command's name in
the string so the whole text would be wrapped.
Change-Id: Idece01ce54994db7e851d8522435ff764b11f3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6223
Tested-by: jenkins
* LICENSES: Add the MIT license
Add the full text of the MIT license to the kernel tree. It was copied
directly from:
https://spdx.org/licenses/MIT.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I94a5dea5ced6421809ea2a3448f8dda19a93f5c9
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6219
Tested-by: jenkins
* stlink: add comment of firmware version for each flag bit
Change-Id: I7f7c7b9c9cfd88125f82662ed864a2c0715140b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6211
Tested-by: jenkins
* stlink: reorder the flag macro by firmware release
The corresponding bit for each macro is changed, but this is not
relevant in the code.
Change-Id: I7039464f5a3d55d008208f44952aadeb815bd5a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6212
Tested-by: jenkins
* tcl/board: Add ST NUCLEO-8S208RB
Change-Id: I384c6ad9b4cbabbc004160677f600d8c4bd3eb71
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6268
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/arm_adi_v5: Fix clear sticky overrun flag during replay of commands
When a WAIT occurs the commands after the WAIT are replayed and the
STICKYORUN is cleared. However if another WAIT occurs during the
command replay, the command itself is resent but the STICKYORUN bit
shall also be cleared. If this is not done, the MEM-AP hangs.
Change-Id: I14e8340cd5d8f58f4de31509da96cfa2ecb630d1
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6278
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: add support for watchpoints
The current implementation of OpenOCD does not support watchpoints for
cortex_a architecture. So, I replaced the add_watchpoint and
remove_watchpoint with the specific implementation for the
cortex a and using the breakpoint implementation and the arm
documentation [1] as reference. In particular, I have made the
following changes:
* added the following functions
- cortex_a_add_watchpoint
This wrapper function check whether there are any watchpoint
available on the target device by calling cortex_a_set_watchpoint.
- cortex_a_set_watchpoint
This function is responsible for settings the watchpoint register
pair. In particular, it sets the WVR and the WCR registers with
the cortex_a_dap command.
- cortex_a_remove_watchpoint
This wrapper function the selected watchpoint on the target device
by calling cortex_a_unset_watchpoint.
- cortex_a_unset_watchpoint
This function sets both the WVR and the WCR registers to zero, thus
unsetting the watchpoint.
[1]
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0464f/BCGDHIEJ.html
Change-Id: I86611dab474cb84836662af572b17636dc68e282
Signed-off-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Reviewed-on: http://openocd.zylin.com/3913
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
* target/cortex_a: fix number of watchpoints
Decrement the available watchpoints only when succeed setting it.
Initialize the available watchpoint with the correct value.
Change-Id: I0f93b347300b8ebedbcd9e718d4ba32b26cf6846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6196
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: add support for watchpoint length of 1, 2 and 4 bytes
Use byte address select for 1 and 2 bytes length.
Use normal mode for 4 bytes length.
Change-Id: I28d182f25145d0635de64d0361d456f1ad96640e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6197
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* target/cortex_a: fix memory leak on watchpoints
The memory allocated to hold the watchpoints is not freed at
OpenOCD exit.
Free the watchpoint memory at OpenOCD exit.
Change-Id: I518c9ce0dc901cde2913d752e3154734f878b854
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6210
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
* helper/jim-nvp: comply with coding style [1/2]
The helper jim-nvp does not comply with OpenOCD coding style due
to typedef of struct and CamelCase symbol names.
While it's trivial fixing the helper and all its current use in
the code, changing these APIs will potentially break a number of
patches pending in gerrit. Gerrit will not trigger any alert, but
the code will generate compile error after the merge.
Add the compile flag "-Wno-error=deprecated-declarations" to keep
as warning (not as error) the use of "deprecated" functions and
types.
Rename all the CamelCase symbols is lowercase and provide struct
prototypes in place of the typedef.
Add a DEPRECATED section to 'jim-nvp.h' where the old CamelCase
symbols and the old typedef are re-declared with compile attribute
'deprecated'.
With this change OpenOCD compiles, but generates warnings.
The remaining changes allover OpenOCD code will be fixed in a
separate patch for easier review.
The patches merged later that still use the old deprecated API
will compile with warnings. This will permit to identify and fix
these cases.
Change-Id: I786385d0f662dbb1be5be313ae42623156d68ce5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6183
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
* helper/jim-nvp: comply with coding style [2/2]
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
* server/telnet: fix autocomplete for jimtcl commands
Current autocomplete filters-out some command reported by "info
commands". One of the filter rule concerns the command's private
data.
Every command registered by OpenOCD has its 'struct command' as
private data.
By ignoring commands without private data, we loose several TCL
commands registered by jimtcl, e.g. 'foreach', 'llength'.
By assuming that every command with non-NULL private data has
'struct command' as private data, we risk at best to access
inconsistent data, at worst to trigger a segmentation fault.
Export the already available functions:
- to check if a command has been registered by OpenOCD and
- to get the private data.
While there, rename jimcmd_is_ocd_command() as
jimcmd_is_oocd_command().
Don't filter-out jimtcl commands with no private data.
Check the private data only on OpenOCD commands.
Change-Id: Ib5bf8d2bc5c12440c0cfae438f637c38724a79b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6282
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
* helper/list.h: align file to Linux v5.12
Main improvement is in the doxygen comments.
Minimize the delta with kernel file.
Skip the functions hlist_unhashed_lockless() and
__list_del_clearprev() that are relevant only in kernel.
Remove gcc extension "omitted conditional operand".
Change-Id: I2e9ddb54cfe2fa5f7cf18f44726acd144e1f98b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6276
Reviewed-by: <rdiezmail-openocd@yahoo.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
* contrib: add an example of using list.h
Change-Id: Ic3d399d7ad2e4d10677cf78d64968040941b74e5
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6280
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* helper/list.h: add mention to the example in contrib
Without such reference, it could be difficult to find the example.
Change-Id: Ia9ffb06bc1a45446c2c7b53197ab3400e1d8a9e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6281
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* tcl/target/stm32f4x: fix hardcoded chip name
Fixes: c945d6e616 ("tcl/target: start using the new TPIU/SWO support")
Change-Id: I4543c9a204f7b4b3b14e6eabc5042653106aff0e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6277
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
* Makefile: add special target .DELETE_ON_ERROR
The special .DELETE_ON_ERROR deletes the target file on recipe error.
Otherwise, an incomplete output file may be considered up to date
the next time around. .DELETE_ON_ERROR provides reasonable
protection at virtually no cost.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: I67dca47ae5ddf3786993c87b9991b3046a85f00b
Reviewed-on: http://openocd.zylin.com/6235
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* gdb_server: Log both incoming and outgoing GDB packets
- Made sure that also outgoing GDB packets are logged,
not only the incoming ones.
- Improved the treatment of non-printable characters
in the packets to make it more robust.
Prior to this change:
- Outgoing packets were not printed unless OpenOCD was
re-compiled with _DEBUG_GDB_IO_.
- Non-prinable characters were only treated in incoming
'X' packets.
After this change:
- Both incoming and outgoing GDB packets are logged
on debug_level >= 3, so that both directions of the
GDB channel are visible.
- Non-printable characters are checked for in every packet
so that hey do not interfere with the terminal.
Change-Id: I0613e57ae5059b3279b0abcb71276cf5719a8699
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/renesas_rz_g2: Introduce tcl config file for RZ/G2 devices
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* drivers/jlink: Remove trailing dots
This makes the messages consistent with most of the rest of
the OpenOCD output.
Change-Id: I915a01187e7fc317e02483ac0bbd39ec077d6321
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target: Use 'bool' for 'reset_halt'
Change-Id: I974a6360ea7467067511541ac212f2e9d3de7895
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6262
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* cmsis_dap: add support for swo commands
Replaced mixed snake_case_CamelCase with snake_case.
Define variables at first-use location.
CMSIS-DAP SWO specification:
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__swo__gr.html
Change-Id: Ieba79b16efd445143f964b614673d041aae74f92
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5820
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Add target_data_bits().
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Avoid non-standard conditionals with omitted operands.
Fixes bug #257.
Change-Id: I05fc6468306d46399e769098e031e7e588798afc
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6271
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* target/startup.tcl: Do not use 'Yoda conditions'
Change-Id: I5e1bbaf032659dda1b365ef4ec6ea4a635d921ce
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6284
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
* Fix build.
Change-Id: I4f2667db91f84f07af354691aac5d4c9e3aea3fa
Signed-off-by: Tim Newsome <tim@sifive.com>
Co-authored-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Co-authored-by: Antonio Borneo <borneo.antonio@gmail.com>
Co-authored-by: Marc Schink <dev@zapb.de>
Co-authored-by: R. Diez <rdiezmail-openocd@yahoo.de>
Co-authored-by: Daniel Anselmi <danselmi@gmx.ch>
Co-authored-by: Evgeniy Didin <didin@synopsys.com>
Co-authored-by: Yasushi SHOJI <yashi@spacecubics.com>
Co-authored-by: Tomas Vanek <vanekt@fbl.cz>
Co-authored-by: Olivier DANET <odanet@caramail.com>
Co-authored-by: Thomas Gleixner <tglx@linutronix.de>
Co-authored-by: micbis <michele.bisogno.ct@renesas.com>
Co-authored-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Co-authored-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Co-authored-by: Jan Matyas <matyas@codasip.com>
Co-authored-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Enclose within double quote the argument of 'expr' when there is
the need to concatenate strings.
Change-Id: Ic0ea990ed37337a7e6c3a99670583685b570b8b1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6160
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
I may have broken memory sampling with this merge.
Conflicts:
doc/openocd.texi
src/helper/command.c
src/jtag/drivers/ftdi.c
src/rtos/FreeRTOS.c
Change-Id: I2b7e09b2d3b244db546c5212532e6b48fb66dca4
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Markus Reiter
Tim Newsome
Marc Schink
Tarek BOCHKATI
Sean Anderson
Antonio Borneo
Nishanth Menon
Jacek Wuwer
Hans-Erik Floryd
Doug Brunner
Joerg Wunsch
asier70
Andreas Sandberg
Wealian Liao
Robbert
Oleksij Rempel
Ranjith Chandran
Jian-Hong Pan
Matthew Mets
Patrick Stewart
Andreas Fritiofson
Florian Fainelli
Marek Vasut
Rohit Singh
micbis
Olivier DANET
Peter Lawrence