Group the reconnections, so that instead of producing
connect $auto$wreduce.cc:455:run$24 [0] 1'0
connect $auto$wreduce.cc:455:run$23 [31] 1'0
connect $auto$wreduce.cc:455:run$23 [30] 1'0
... (40 more lines)
we produce
connect $auto$wreduce.cc:461:run$23 [31:11] 21'000000000000000000000
connect $auto$wreduce.cc:461:run$24 [31:10] 22'0000000000000000000000
.
If the `$ge` cell we are replacing has wide output port, the upper bits
on the port should be driven to zero. That's not what a `$not` cell with
a single-bit input does. Instead opt for a `$logic_not` cell, which does
zero-pad its output.
Fixes#3867.
C does not guarantee that stdout/stderr can be reassigned.
Most platforms do make them assignable, however musl and WASI that
is based on musl do not. WASI does not have `dup2()`; instead it has
its own non-portable version of it that can only assign to previously
allocated fds.
Update the stream redirection code so that it does the right thing
on WASI and other platforms.
This is mostly important for YoWASP builds, since those do not have
a way to build with external ABC (I prototyped it but for some reason
ABC always segfaults when built as an independent Wasm binary...)
Distinguish between the A, B input ports of `$_ANDNOT_`, `$_ORNOT_`
gates when considering those for sharing. Unlike the input ports of the
other supported single-bit gates, those are not interchangeable.
Fixes#3848.
An `std::vector<T>::reverse_iterator` stores the
`std::vector<T>::iterator` which points to the (forwards-ordered)
*following* item. Thus while `vec.rbegin()` dereferences to the final
item of `vec`, the iterator it wraps (`vec.rbegin().base()`) is equal to
`vec.end()`.
In the remove case here, we advance `it` (backwards), erasing the item
we just advanced past by grabbing its (pre-increment) base
forward-iterator and subtracting 1.
The iterator maths here is obviously all OK, but the forward-iterator
that `it` wraps post-increment actually points to the item we just
removed. That iterator was invalidated by the `erase()` call.
That this works anyway is (AFAICT) some combination of luck and/or
promises that aren't part of the C++ spec, but MSVC's debug iterator
support picks this up.
`erase()` returns the new iterator that follows the item just erased,
which happens to be the exact one we want our reverse-iterator to wrap
for the next loop; we get a fresh iterator to the same base, now without
the preceding item.
This makes clk2fflogic add an attr to $ff cells that carry the state of
the emulated async FF. The $ff output doesn't have any async updates
that happened in the current cycle, but the $ff input does, so the $ff
input corresponds to the async FF's output in the original design.
Hence this patch also makes the following changes to passes besides
clk2fflogic (but only for FFs with the clk2fflogic attr set):
* opt_clean treats the input as a register name (instead of the
output)
* rename -witness ensures that the input has a public name
* the formal backends (smt2, btor, aiger) will use the input's
name for the initial state of the FF in witness files
* when sim reads a yw witness that assigns an initial value to the
input signal, the state update is redirected to the output
This ensures that yosys witness files for clk2fflogic designs have
useful and stable public signal names. It also makes it possible to
simulate a clk2fflogic witness on the original design (with some
limitations when the original design is already using $ff cells).
It might seem like setting the output of a clk2fflogic FF to update the
input's initial value might not work in general, but it works fine for
these reasons:
* Witnesses for FFs are only present in the initial cycle, so we do
not care about any later cycles.
* The logic that clk2fflogic generates loops the output of the
genreated FF back to the input, with muxes in between to apply any
edge or level sensitive updates. So when there are no active updates
in the current gclk cycle, there is a combinational path from the
output back to the input.
* The logic clk2fflogic generates makes sure that an edge sensitive
update cannot be active in the first cycle (i.e. the past initial
value is assumed to be whatever it needs to be to avoid an edge).
* When a level sensitive update is active in the first gclk cycle, it
is actively driving the output for the whole gclk cycle, so ignoring
any witness initialization is the correct behavior.
When assigning values to input ports of nested modules in cosimulation,
sim needs to find the actual driver of the signal to perform the
assignment. The existing code didn't handle unconnected inputs in that
scenario.
Allow Liberty canonical identifier including double quotes in if-body and pass-through for Synopsys-style unquoted identifiers issue#3498
Co-authored-by: Aki <201479+lethalbit@users.noreply.github.com>
Writeback of simulation state into initial state was only working for `run()` and `run_cosim_fst()`.
This change moves the writeback into the `write_output_files()` function so that all simulation modes work with the writeback option.
This was renaming cells while iterating over them which would always
cause an assertion failure. Apparently having to rename cells to make
all witness signals public is rarely required, so this slipped through.
whitequark
Martin Povišer
N. Engelhardt
Jannis Harder
Claire Xen
Charlotte
Eddie Hung
gatecat
Muthiah Annamalai (முத்து அண்ணாமலை)
Muthu Annamalai
Miodrag Milanović
Krystine Sherwin
Muthu Annamalai
Aki Van Ness
Benjamin Barzen