Reading of DPIDR is the very first operation after JTAG to SWD sequence.
Without this change if DPIDR read fails then swd connect fails.
Keep trying JTAG to SWD sequence and DPIDR read until success
or timeout 0.5 sec. It makes setting of adapter srst delay on SWD transport
mostly unnecessary.
Also test for ERROR_WAIT (which should not occur according to
IHI 0031E B4.3.2 but a quirk is known) and if bus is kept stalled
then issue abort to make the next connect possible.
Change-Id: Id8fe6618605bbeb4fed5061e987ed55de90a35f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5730
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If dap_dp_read_atomic() in 30 trials loop fails, dap->do_reconnect is set.
Following dap_dp_read_atomic() calls dap_queue_dp_read() which in case
of SWD transport calls swd_queue_dp_read(). It starts
with swd_check_reconnect() and it calls swd_connect() because
dap->do_reconnect is set. swd_connect() does some initialization,
reads DPIDR and calls dap_dp_init() again!
Moreover if dap_dp_init() is called from cortex_m_reset_(de)assert()
one level of recursion is necessary to reconnect the target.
Introduce dap_dp_init_or_reconnect() for use in cortex_m reset
and similar.
Remove loop of 30 atomic reads of DP_STAT to prevent unwanted recursion.
Change-Id: I54052fdefe50bf5f7c7b59fe751fe2063d5710c9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5729
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Change-Id: I4fea29f07f4d3b8b2578b538ef0eef5f1eea285f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5876
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a Cortex-M (not M0, M0+) target was stopped in the middle of
a conditional IT block or in the load/store multiple instruction,
cortex_m_debug_entry() used wrong xPSR bits to detect it and then
cleared 8 bits of the exception number from xPSR
- probably wrong bit mask again.
I believe clearing of the ICI/IT bits in cortex_m_debug_entry() has no
reason as Cortex-M does not use instruction injecting.
Remove the wrong code.
The change was originally a part of http://openocd.zylin.com/4862
It is now re-submitted as #4862 is not ready.
Change-Id: If91cd91d1b81b2684f7d5f10cf20452cde1a7f56
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5874
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Consolidate low level register read/write.
Floating point registers were handled by target_read/write_u32
unlike other registers handled by cortexm_dap_read/write_coreregister_u32
There is no reason to do so in cortex_m.
Remove cortexm_dap_read/write_coreregister_u32
and use cortex_m_load/store_core_reg_u32 directly.
Similarly HLA adapters register read/write interface supports all registers
so use it for any floating point and other registers.
Change-Id: Ida679e5f4fec02d94ffb0bd3f265ed7ed2221cdc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5864
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Move primask/basepri/faultmask/control packing/unpacking from
cortex_m.c and hla_target.c to armv7m.c armv7m_read_core_reg()
and armv7m_write_core_reg() where also the FP 32/64-bit registers
conversion takes place.
Introduce a new hidden register ARMV7M_PMSK_BPRI_FLTMSK_CTRL
for packing/unpacking of special registers in the register cache.
The new packing/unpacking is endianess safe.
While on it improve returned error codes and LOG_ messages.
Just minimal changes in cortex_m.c and hla_target.c, will be
consolidated in the next patch.
Change-Id: Id51e764e243e54b5fdaadf2a202eee7c4bc729fe
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5863
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Make arm register id coherent with reg_list index.
Without this reg_list[ARMV7M_R12] was possible but
reg_list[ARMV7M_FPSCR] was out of bounds.
Remove unused items from reg_list index.
Change-Id: I84d3b5c496fc1839d07a5b74cb1fd1c3d4ff8989
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5862
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Define a new enum with DCRSR.REGSEL selectors.
Introduce armv7m_map_id_to_regsel() to unify mapping in one place.
Use DCRSR.REGSEL selectors for low level register read/write.
Change-Id: Ida0ccdfa9cdb1257a1900b8bfbf172b076374d39
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5327
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Introduce a 'hidden' flag in struct reg to support a register cache
containing different views of same data: e.g. Cortex-M has
primask, basepri, faultmask and control registers accessed
as one word. With the hidden flag we can add an reg_list item
corresponding to hw access without exposing the register to user level.
All the struct reg are allocated with calloc() but one in xscale.c
allocated by malloc(). Change this one to use calloc() as well
to guarantee initial value hidden=false
Change-Id: I8da9f5a5a60777ae7ef943a841307487bd80fc6f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5325
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
When the core is in sleep mode, the core is no longer retiring
instructions. Cortext M remains in "unknown" state. This patch converts
sleep mode to "running" state.
Change-Id: I1e9b6c9be51fd0f1f6ce81af9b1f5f9f1f43c661
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5921
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
The function arm7tdmi_clock_out() has one unused 'deprecated'
parameter.
Drop the unused 'deprecated' parameter and the FIXME above it.
Change-Id: Ia8de41f5b8258825faccc737bba622e44c81a7ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5912
Tested-by: jenkins
When a target examination fails, continue to examine subsequent targets.
Return the number of targets that failed to examine.
Change-Id: I883a0c445edc7eb00f496b79271d773771ec6b66
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When trace capturing the trace is enabled using 'tpiu_config internal'
(via the internal mode), OpenOCD can collect the trace buffers then append
it to a specified file or named pipe and propagate the trace to 'tcl_trace'
command.
This change is allowing OpenOCD to stream the captured trace over TCP.
When using this configuration OpenOCD acts like a server and multiple
clients can connect and receive the captured trace.
Example on STM32F7 running at 216MHz:
itm port 0 on
tpiu config internal :3344 uart off 216000000
Change-Id: Idea43e7e26e87b98a33da7fb9acf7ea50fe3b345
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5345
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
returning the created service seems useful:
as the only method to get the freshly created service is by getting the
last item in the services linked list, and this seems to be like an
intrusion to service internal mechanism.
possibly, we could get the service from a connection but this is possible
only from [new_connection|input|connection_closed]_handler_t, but this is
not always practical:
example: armv7m: add a TCP channel to stream captured trace
http://openocd.zylin.com/#/c/5345/
here we poll for trace and broadcast to all connections
outside of these xxx_handler_t functions
also, storing one of the connections in new_connection_handler_t and get
the service from it is possible, but this will make the code less readable.
Change-Id: I5fef1baecec1e054953c6faf5b99d864ecc97f02
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5717
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Functions that are not used outside the file should be declared as
static.
Change-Id: Ie81f6bdce91e2a1456364b47f30aa4d35c7ee7bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5900
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9f97571a528f0cb3c3c26f873577ab16fdec3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Is it possible to run OpenOCD without any target, for example to
only dump the rom-tables of an arm dap, or to perform low level
jtag operations.
But without any target created, the command 'target current'
causes OpenOCD to abruptly exit.
Handle in command 'target current' the case of no targets.
Change-Id: Ide15cb13bec84b88ccc3e7126523c04a6d70e636
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5881
Tested-by: jenkins
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
To avoid code duplication, reorganize the code to replace
cti_configure() with adiv5_jim_mem_ap_spot_configure().
Reorganize 'struct arm_cti_object' and its sub-'struct arm_cti'
moving DAP and mem-AP info in a 'struct adiv5_mem_ap_spot'.
Replace cti_configure() with adiv5_jim_mem_ap_spot_configure().
Deprecate the use of '-ctibase' in favor of '-baseaddr'.
Change-Id: I43740a37c80de67c0f5e4dc79c3400b91a12e9e8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5869
Tested-by: jenkins
This is somehow an extension of existing adiv5_jim_configure(),
but includes the 'address' in the mem_ap.
Rewrite adiv5_jim_configure() using the new helper.
Change-Id: Ia7effeeece044004d459b45126ed4961a98b8568
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5857
Tested-by: jenkins
Now that it’s possible to start profiling from either a running or a
halted state, rather than unconditionally halting after profiling
finishes, it makes more sense to restore the processor to whatever state
(running or halted) it was in before profiling started.
Change-Id: If6f6e70a1a365c1ce3b348a306c435c220b8bf12
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5237
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Cortex-M implementation of profiling contains a bunch of
conditionals and checks to handle both chips which have PCSR and chips
which do not. However, the net effect of the non-PCSR branches is
actually exactly the same as what target_profiling_default does. Rather
than duplicating this code, just detect the situation where PCSR isn’t
available and delegate to target_profiling_default.
Change-Id: I1be57ac77f983816ab6bf644a3cfca77b67d6f70
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are a handful of implementations of profiling. There is the
default implementation, which repeatedly halts and resumes the target,
sampling PC each time. There is the Cortex-M implementation, which
uses PCSR if available, otherwise falling back to halting and resuming
and sampling PC. There is the OR1K implementation, which reads NPC
repeatedly. Finally, there is the NDS32 implementation which uses some
kind of AICE commands with which I am unfamiliar.
None of these (with the possible exception of the NDS32
implementation) actually require the target to be halted when starting
profiling. The Cortex-M and OR1K actually resume the target as pretty
much their first action. The default implementation doesn’t do this,
but is written in such a way that the target just flips back and forth
between halted and running, and the code will do the right thing from
either initial state. The NDS32 implementation I don’t know about.
As such, for everything except NDS32, it is not really necessary that
the target be halted to start profiling. For the non-PCSR Cortex-M and
default implementations, there is no real harm in such a requirement,
because profiling is intrusive anyway, but there is no benefit. For
the PCSR-based Cortex-M and the OR1K, requiring that the target is
halted is annoying because it makes profiling more intrusive.
Remove the must-be-halted check from the target_profiling function.
Add it to the NDS32 implementation because I am not sure if that will
break when invoked with a running target. Do not add it to any of the
other implementations because they don’t need it.
Change-Id: I479dce999a80eccccfd3be4fa192c904f0a45709
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5235
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With help of actionpoint mechanism now it is possible to introduce
watchpoints support for ARC.
Change-Id: I5887335d0ba38c15c377bc1d24a1ef36e138cf65
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5867
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Bit 2 of control register is used if the processor includes the FP
extension
Change-Id: Ie21bc9de8cae5bad9d841e1908eff3aa0bb29d4b
Signed-off-by: Sylvain Chouleur <schouleur@graimatterlabs.ai>
Reviewed-on: http://openocd.zylin.com/5853
Reviewed-by: Sylvain Chouleur <sylvain.chouleur@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The commit b68674a1da ("Upstream tons of RISC-V changes.") was
proposed well before commit 3ac010bb9f ("Fix debug prints when
loading to flash"), but the merge got in different order.
After latest merge, the master branch fails to compile.
Fix the compile error.
Change-Id: Ia3bd21d970d589343a3b9b2d58c89e0c49f30015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5856
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
The function adiv5_jim_configure() casts the void pointer
'target->private_config' to a struct adiv5_private_config pointer.
This is tricky in case of aarch64, where the private data are in a
struct aarch64_private_config that has as first element the struct
adiv5_private_config.
While the current solution is working fine, it's not clean and
requires special attention for any further code development.
Override 'target->private_config' to the correct pointer while
calling adiv5_jim_configure().
Change-Id: Ic2fc047dd1e57013943d96e6d5879a919d1eb7b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5847
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Change aarch64 to use ap-num setting if provided. Fall back to original
behavior of using first AP when ap-num is invalid.
Change-Id: I0d3624f75c86ba5fd5a322ac60856dbbb6e71eaf
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5831
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If a target is not examined, command vector_catch crashes while accessing
the debug_ap NULL pointer.
maskisr and reset_config commands don't require this check.
Change-Id: I949b6f6e8b983327dd98fbe403735141f8f0b5d6
Signed-off-by: Daniel Trnka <daniel.trnka@gmail.com>
Reviewed-on: http://openocd.zylin.com/5813
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
In target/openrisc/jsp_server.c, an error is logged if the ptr was
already NULL. This cannot happen since the pointer was already
referenced few lines before and openocd would have been already
SIGSEGV in that case, so remove the log.
Change-Id: I290a32e6d4deab167676af4ddc83523c830ae49e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5809
Tested-by: jenkins
The prompt pointer in the jtag serial port is never zero'd or allocated.
Completely remove it since there is not much use for it as the target
software will provide the actual prompt.
Change-Id: Id95d8ccb9f725e53b9d03386b11d91eba1cd6ef4
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-on: http://openocd.zylin.com/4093
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: If10a0f1c254aee302b9ca08958390b7f21cdb21b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5824
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: I691094a6395acb0e4ea3bea2347ff38379002464
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5822
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
While there, fix prototype mismatch between header and C file of
the function armv7a_l1_d_cache_inval_virt().
Change-Id: I434bd241fa5c38e0c15d22cda2295097050067f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5818
Tested-by: jenkins
Commit 11019a824d ("adi_v5: enforce check on AP number value")
introduces the macro DP_APSEL_MAX and use it in place of hardcoded
magic numbers for the upper limit of AP selection value.
Use the macro also while defining the array of struct adiv5_ap in
struct adiv5_dap.
Change-Id: I88f53ceb710f92a48a8026a365709fbf2d9e6912
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5806
Tested-by: jenkins
While loading to flash with debug level at least 3,
OpenOCD tries to print the whole loaded bitstream.
This will be very-very-slow due to implementation of
conversion from buffer to string.
* fix condition on selected debug level in jtag/core.c
* replace slow buf_to_str function from helper/binarybuffer.c
with faster but_to_hex_str function
Change-Id: I3dc01d5846941ca80736f2ed12e3a54114d2b6dd
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
Reviewed-on: http://openocd.zylin.com/5800
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are failure cases of target_create() that are not checked.
Plus, in case of failure the memory allocated in not properly
released before returning error.
Check all the possible failure in target_create().
Change current_target only when target is successfully created.
Add the new target to all_targets list only when target is
successfully created.
Release all the allocated memory before quit on failure.
Use malloc() instead of calloc() for target->type, because the
struct will be fully populated with memcpy().
Change-Id: Ib6f91cbb50c28878e7c73dc070b17b8d7d4e902f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5776
Tested-by: jenkins
Tomas Vanek
Antonio Borneo
Kevin Yang
Andreas Bolsch
Marc Schink
Adrian Negreanu
Tarek BOCHKATI
Christopher Head
Evgeniy Didin
Sylvain Chouleur
Tim Newsome
Daniel Trnka
Mete Balci
Stafford Horne
Samuel Obuch