instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In flash/nor/cfi.c:835 struct cfi_info is allocated by malloc(). As
write-mem was uninitialized the pointer pointed to an out of range
address, which led to a segmentation fault and crashed openocd.
This happened during flash-command of an external flash-bank, using
cfi.
Use calloc() instead.
While on it check for NULL return and remove unnecessary initialzation.
Change-Id: I0e2ffb90559afe7f090837023428dcc06b2e29f6
Signed-off-by: Mischa Studer <mischa.studer@csa.ch>
Reviewed-on: http://openocd.zylin.com/6070
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This removes some warnings which prevent a successful build with -Werror
which is enabled by default. I'm using gcc 11, so maybe others are not
getting this warnings yet.
In src/flash/nor/numicro.c the debug messages were misleadingly indented.
In src/target/arm920t.c the array size where smaller than expected from
the receiving function.
Change-Id: I66f5c6a63beb9f9416e73b726299297476c884d8
Signed-off-by: Rene Kita <git@rkta.de>
Reviewed-on: http://openocd.zylin.com/6104
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is specially needed when, in the probe routine, device is not
found among the stm32l4_parts. In this case, the stm32l4_flash_bank->part_info
is undefined and inadvertentanly used afterwards:
part_info = stm32l4_info->part_info;
If the stm32l4_flash_bank is zero init, the probe routine checks for
the validity of the part_info field in the previous struct and correctly
detects the unsupported (or not found) condition, raising an error
rather than a SIGSEGV
Change-Id: I7d9d669fb3fa7f8f0903acd60046966b4acb0031
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6103
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no good reason to use macros instead of static inline functions. The
current code is hard maintain. For example, it changes variables outside of the
macro scope. Also, it is conflicting with the C coding style.
Change-Id: I5ac9d2ae076ef73c176d4e32b2e7e0a99fa875ab
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6046
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The C style guide forbids typedef'd structs, see 'Naming Rules'.
Change-Id: I983dd52307136d1b5adb58d8c44c0c14422d31e2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6032
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/flash/nor/stmqspi.c: In function ‘read_flash_id’:
/src/flash/nor/stmqspi.c:1948:6: error: ‘retval’ may be used uninitialized
Change-Id: Ifd8ae60df847fc61e22ca100c008e3914c9af79b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6012
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
The relative path should have three times '..'.
Issue identified by doxygen:
src/flash/nor/max32xxx.c:85: warning: include file
../../contrib/loaders/flash/max32xxx/max32xxx.inc not
found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Change-Id: Ie7b4948c6770b8acb9eff26e08eea32945ebb219
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5997
Tested-by: jenkins
The warning message regarding wrong verification checksum for LPC2000, claims that the verification will fail, but the checksum written correctly by openocd. Clarify this in the warning message.
Change-Id: I929ac767f7f9fdad9bace250c8c04a776462800a
Signed-off-by: Luca Lindhorst <l.lindhorst@wut.de>
Reviewed-on: http://openocd.zylin.com/5956
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The git preliminarily version of clang 12.0.0_r370171
f067bc3c0ad6 reports an error in the expansion of the macro
SMI_READ_REG():
error: '(' and '{' tokens introducing statement expression
appear in different macro expansion contexts
[-Werror,-Wcompound-token-split-by-macro]
Remove one intermediate macro expansion to make clang happy.
Change-Id: I8ae6d9c18808467ba8044d70cbf0a4f76a18d3e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5958
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
flash_regs table is introduced within stm32l4_flash_bank struct in order
to get correct register offsets, by using the driver internal function
'stm32l4_get_flash_reg_by_index'.
To use efficiently register indexes, stm32l4 _[get|read|write]_flash_reg
functions are surcharged to accept register indexes.
IMPORTANT: stm32l4_write_option is not surcharged, and they always accept
the option register offset.
tested on NUCLEO-G474RE and STM32L4R9I-DISCO
Change-Id: I739d3e97d63b831af6aa569c5629db0000209551
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5509
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
PSoC6 erases flash to 0x00 not more common 0xff, so a device
with erased flash loads xPSR.T=0 from the zeroed reset vector.
Wrong thumb bit value caused a target algorithm failed with HardFault.
The low level write to xPSR solved the problem only if xPSR cached
copy was not marked dirty.
Later commit 49bd64347a fixed T setting
for all Cortex-M target algorithms.
Since 49bd64 this part of code is useless as xPSR target_start_algorithm()
sets always xPSR dirty so the effect of the low level write is eliminated
(and proper setting of thumb bit is ensured in target_start_algorithm())
Change-Id: I68aea5e921fbc6203f2fe91a45f10d22869327de
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5875
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I52d46ed6d4c9b98a7152eb23274c836416f409a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Warning: line 679, column 4
4th function call argument is an uninitialized value
Change-Id: If62d96e1595be945c8e17885bb402e820fb1ec7b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5903
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
HWID is a part of 32 bit CONFIGID register. hwid member of struct nrf5_info
was typed uint32_t to enable direct CONFIGID read and masked afterwards.
Change to uint16_t to unify with hwid in struct nrf5_device_spec
and RM description.
Change-Id: Ib720d3ce23c301aee41d074ea78a6f00a23aed68
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5589
Tested-by: jenkins
nRF52 devices indicate a flash error by emitting hard fault
exception (unlike nRF51 series).
Change error message when NVMC READY read fails. A hard fault
from flash erase/write operation is detected here.
Check exit point of the flash write algo to ensure a failed
write is recognised.
Change-Id: I637eda268a6bf45f7f41bcb9dcd82db8f5cb41b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5587
Tested-by: jenkins
nRF51 devices have a clumsy flash protection based on UICR CLENR0.
A code running in RAM can write to a protected flash region without
any hint the protection gets violated.
NVMC flash page erase obeys protection setting but fails absolutely
silently.
Before this change the first problem was not addressed in the code.
To justify the second one, protection was loaded during probe,
after protection setting and after a mass erase.
Move protection updates to the beginning of erase/write operation
and limit them to nRF51 series only. Check for protected sectors
before write.
The change also fixes the problem of 'nrf5 mass_erase' on
nRF52833/840 devices. They use ACL flash protection, which is not
supported in nrf5 driver. mass_erase then looked like it failed.
Change-Id: Ie58cda68eb104d410b02777c3df5b343408e2666
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5522
Tested-by: jenkins
Protection setting has not ever worked. UICR CLENR0 register cannot
be simply written but has to programmed because it resides in UICR
page of the flash.
Enable flash programming before writing CLENR0 and set back to r/o
afterwards.
Inform the user that reset might be required.
Change-Id: Ib0f96c74ba3583ac33f4394ddb57d8c8895adf53
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5586
Tested-by: jenkins
Add support for ATSAMG55x19 Rev.B.
Both chips have nearly the same cidr, however, Rev.B has an incremented version.
Change-Id: I5939c41fa5d54c4d3bfb850964974b878f709d13
Signed-off-by: Benedikt-Alexander Mokroß <mokross@gessler.de>
Reviewed-on: http://openocd.zylin.com/5825
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
STM32H72x/73x flash is similar to STM32H74x/75x,
except STM32H72x/73x devices have only one single flash bank.
Change-Id: I3d3422dc60234f8273172924f426200210f388cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5792
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Modify the format strings to properly handle uint32_t data types.
Change the type of variable retval in 'nor/ambiqmicro.c' to match
both the value to carry and the returned type of the function.
Fix the prototype mismatch of function lpc2900_address2sector()
between the header and the C file.
Change-Id: I68ffba9bd83eec8132f83bff3af993861fd09d84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5816
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
There are cases where the pointer is set to NULL after free(), but
then re-assigned within few lines. Drop the setting to NULL when
this is evident. Anyway, the compiler will remove the useless
assignment so no reason to be too much aggressive in this change.
Change-Id: I55b2ce7cbe201410016398933e34d33a4b66e30b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5811
Tested-by: jenkins
Either of protect and protect_check driver callbacks can be NULL. In
virtual_protect, reuse flash_driver_protect which checks for that case
and generates a nice error message and return code. In
virtual_protect_check, there is no corresponding flash_driver_*
function, so add the NULL check directly.
Change-Id: Ia63d85ede640a8382cf5cad0760f5d1ffe4d7cfe
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5782
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I677bc4487fc2eff2c32e14ca2db5470fddaa63b5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5778
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I06a8344d0ed62de7a0f3e2dd8fba69b17eeb3626
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5783
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this flash is used on the Digilent CMODA7 FPGA board
Change-Id: I6749ca3fbebf2e384051a26a3fd253da5d6e25fb
Signed-off-by: Michael Betz <michibetz@gmail.com>
Reviewed-on: http://openocd.zylin.com/5787
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix typos and duplicated words in comments and strings.
Change-Id: I64282c7018462deefeeb8e5f4d0d81942425b3fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5758
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I77e8dd161887f02ecf8019b43d3e8e7cc122ad0e
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5780
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Kinetis Flash Configuration Field needs special handling to prevent unwanted
locking of the device. Warn user about any difference between generated
FCF and FCF data in the programmed file. Inform user that re-programming
of already programmed FCF may fail on devices with FTFE flash module.
While on it remove useless setting of is_erased flag after erase.
Change-Id: I3911f436674547fa12ef3886c7d5e8cd889f9e2b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: https://sourceforge.net/p/openocd/tickets/270/
Reported-by: Noel Diviney <vk3avm@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/5753
Tested-by: jenkins
Since e22c6484ea the trial/error allocation shows
"not enough working area available(requested 2048)" message
on klx.cfg. The message is not clear if it means a problem or not.
Replace with new style allocation using target_get_working_area_avail()
Change-Id: I87fe1e38248fcac29982b72aaba12217a0552f38
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5752
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
It is an error to prefix with "0x" the print of values in decimal.
Replace the incorrect decimal format specifier with PRIx32.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types PRINTF_0XDECIMAL -f {} \;
Change-Id: I2eb867ef654527b2737ba573a405ec8f97c6a739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib9c567e2287f2a99172bd3bd35a81e3205cea421
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5749
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use 'unsigned int' and 'bool' instead of 'int' where appropriate.
While at it, fix some coding style issues.
No new Clang analyzer warnings.
Change-Id: I700802c9ee81c3c7ae73108f0f8f06b15a4345f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4929
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to the datasheet, erasing a block can take up to 200 ms.
When using a Segger J-Link with a 2 MHz clock the current loop
finishes after < 50 ms, ignores the timeout, and then fails when
erasing the next block.
Switch to a time based check, add an explicit yield, and report an
error on timeout.
Change-Id: I8255401d1e59f427a08d2cccb8a66143dcdbb324
Signed-off-by: Michael Hope <mlhx@google.com>
Reviewed-on: http://openocd.zylin.com/5706
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current version erroneously allows any number of arguments >= 1.
Change-Id: I64156c11b48d411c72bebbf866954818cd036ff2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5716
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Flashing Kinetis MCU MK22FX512VLH12 takes longer than one second,
thus gdb connection can timeout. Before commit 7f260f5009
("helper/command: Handle Tcl return values consistently") the
openocd timeout warning was masked by a bug in gdb_put_packet()
that resets the timeout counter if any message is logged out.
The commit above removes one log message and the timeout warning
is now triggered.
While the bug in gdb_put_packet() is still to be fixed, the reason
of the timeout is the lack of keep_alive() calls in kinetis flash
driver.
Add keep_alive() call at every iteration in function
kinetis_write_sections(), that is reported as core write function
in chunks of 1024 bytes in the log from the reporter.
Add also a keep_alive() call at every iteration in function
kinetis_write_inner(). This part is not present in the log but, by
code analysis, it represents another critical loop.
Change-Id: I38e631b36c7eb2f1e21cef68710ce47c03d3edda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Jonatan Hatakeyama Zeidler <jonatan.zeidler@medineering.de>
Reviewed-on: http://openocd.zylin.com/5703
Tested-by: jenkins
Reviewed-by: <jonatan_zeidler@gmx.de>
This is a follow-up to 3c9bd7c6f3.
Change-Id: If430f7fcfbba084d9cd74b32344ad43508a96a77
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The statement "else" should not be on a new line when follows a
close brace '}'. Fix it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ELSE_AFTER_BRACE -f {} \;
Change-Id: I8af247ec3f75a69713d7cb1e73881254d16c189e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5623
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
this change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
a table with register offset will be introduced, thus correct register
addresses will be obtained using this table and the driver internal
function 'stm32l4_get_flash_reg' will be responsible of this.
Change-Id: I74bf61a83fe53575623640af0328b3253ecc796f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5508
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Michael Jung <mijung@gmx.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to RM0432 rev. 6, only 0x1001 "Z" rev. applies for STM32L4P5/Q5.
Verified on real device. Whether other revisions exist is unclear.
Change-Id: I761ae077d089b06925fc0fe1ff2b1e478b8a66fa
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5521
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix build error on Mac OS X Catalina (10.15.4) caused by formatting
stm32l4_info->wrpxxr_mask, which is uint32_t, as uint16_t in the debug
log message. Adding casting to uint16_t before substitution because only
lower 16 bits are significant for debug purposes.
Change-Id: Iddb87cd156dfc84ab1f91cd15a1ddee6b646d412
Signed-off-by: Ilya Kharin <akscram@gmail.com>
Reviewed-on: http://openocd.zylin.com/5590
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some flash banks are not mapped in the target memory
(e.g. SPI flash, some special pages).
Add flash version of mdw/h/b which reads data using
the flash driver.
Change-Id: I66910e0a69cf523fe5ca1ed6ce7b9e8e176aef4a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4776
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If watchdog is enabled, there's no way we can disable it while the flashing firmware
is running. (Halt disables it, but software reset doesn't.) So let's have the flashing
firmware refresh the watchdog regularly, in case it has been enabled by previously
running software. Failure to do so could lead to a watchdog reset in the middle of
the chip bieng programmed.
Change-Id: I79d41593948aae0080480e891552e1c2ee3ccbd0
Signed-off-by: Aurélien Martin <martaurel@gmail.com>
Reviewed-on: http://openocd.zylin.com/5266
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
core.c:446:
The left operand of '>>' is a garbage value
There are many places where an error code returned from nand->controller
operations are ignored. To keep the change minimal, the error checks are
added only to reading of extended nand info as it was suspected
to be the cause of the warning.
Addition of the error checks did not fix the warning.
scan-build-9 report was inspected and IMHO the warning is bogus:
the term (nand->device->erase_size == 0) cannot give false at line 395
and then evaluate true at line 462. Fixed by zeroing id_buff.
Change-Id: I97ed7ce0fdf1aa23d746d5fb898bacd050e20ae8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5518
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
For flash/nor/efm32 the EFM32GG12B Giant chip has been added to the
efm32_family along with its respective series and msc_rebase.
Testen on EFM32GG12B390F board
Change-Id: Idd7dfa93f26ac22566aed1be28f30db678cc0a25
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5567
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
In newlib, the argument of isalnum() and the similar functions in
ctype.h is checked to be either an int or an unsigned char.
Using a normal (signed) char triggers a compile time warning
warning: array subscript has type ‘char’ [-Wchar-subscripts]
Rewrite the function to separate the internal unsigned char
operations from the (signed) char parameter.
Change-Id: I5f19115f0b2de2b5b35dc07ef4b58a96161268ee
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Fixes: 5da746fa09 ("flash/nor/nrf5: detect newer devices without HWID table")
Reviewed-on: http://openocd.zylin.com/5545
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
On stm32h747 writing/erasing bank 1 didn't work. It was because the
flash register base was always set for bank 0.
Tested on STM32H747I-DISCO board.
Change-Id: I7e8c43ecdda9dc70b114905f5ec6a6753ca29d82
Signed-off-by: Sasha Kozaruk <alkhozar@gmail.com>
Reviewed-on: http://openocd.zylin.com/5534
Reviewed-by: Christopher Head <chead@zaber.com>
Tested-by: jenkins
Change the current message when a flash driver does not implement
the protect_check function to LOG_INFO() from LOG_WARNING(). The
user is still notified that the procedure isn't available, but
changes the tone to indicate this is expected with this flash
driver and not something that necessarily is a problem to fix.
Change-Id: If8a2e86a23c852d562346ca36734e5d02df4a851
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5539
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This adds the ATmega256RFR2 to the list of know devices for flashing.
Change-Id: Ib24a508762aaa84ba08ba37409db2ae674b46288
Signed-off-by: Lars Pöschel <poeschell+openocd@mailbox.org>
Reviewed-on: http://openocd.zylin.com/5504
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current method used for flash addressing uses 16 bit. Every access
to flash is 16 bit wide. With 16 address bits one can address 0x10000
unique locations á 16 bits thats 0x20000 bytes.
For flashes bigger than that avrs have an extended addressing with more
than 16 address bits. This is now implemented and used for flashs larger
than 0x20000 bytes.
Change-Id: Id8b6337dde3830fb3c56b9042872e040bb67c12d
Signed-off-by: Lars Pöschel <poeschell+openocd@mailbox.org>
Reviewed-on: http://openocd.zylin.com/5502
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32WB3x devices' flash are quite similar to STM32WB5x,
except the maximum flash size, which is 512K for WB3x and 1M for WB5x
Change-Id: I3098d7153a7429e0e72c75cec962c05768b0b018
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5475
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32WLEx devices are based on arm Cortex-M4 running at 48MHz,
contains a single bank of maximum 256 Kbytes of flash memory.
there is 3 variants with different Flash/RAM sizes:
STM32WLE5JC : 256K/64K
STM32WLE5JB : 128K/48K
STM32WLE5J8 : 64K/20K
the work-area size is set to 20 kb to fit in STM32WLE5J8
Change-Id: Ie8e186fe4be97cbc25c53ef0ade4b4dbbcee6f66
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5450
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
+ minor changes in comments' alignment to please our eyes
Change-Id: Ifa35a1032afc4e9aee524f596c0298a9eea49c37
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5500
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
STM32G0 and G4 uses the same flash driver as the stm32l4x
Change-Id: Ic1c4be70aaee809536912e0390f07893efb9a082
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5482
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Flash module of STM32G0/G4 family is quite similar to the one of
STM32L4, so only minor changes are required, in particular
adaption of flash loader to Cortex-M0. Register addresses
passed to flash loader to simplify integration of L5.
Added re-probe after option byte load.
Added flash size override via cfg file.
WRPxxR mask now based on max. number of pages instead of fixed 0xFF,
as G4 devices fill up unused bits with '1'.
Sizes in stm32l4_probe changed to multiples of 1kB.
Tested with Nucleo-G071RB, G030J6, Nucleo-G431RB and Nucleo-G474RE.
Gap handling in G4 Cat. 3 dual bank mode tested with STM32G473RB.
This handling isn't optimal as the bank size includes the
size of the gap. WB not tested.
Change-Id: I24df7c065afeb71c11c7e96de4aa9fdb91845593
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4807
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added fixes for issues found in additional code reviews.
Fixed host Endianness issues with using buffer reads
and writes instead of the *_u32 variants.
Changed code that tried to ID banks by hardcode
bank_number values to use instead the bank base
address. This fixes problems using configurations
with multiple devices.
Note that this replaces Change 4786 which has
been abandoned because of extensive changes to
the code to stop IDing banks by name. And I
think I really messed up a rebase/merge on the
document file.
Tested on MSP432P401R, MSP432P4111, and MSP432E401Y
Launchpads.
Change-Id: Id05798b3aa78ae5cbe725ee762a164d673ee5767
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5481
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Adopted only fast algorithm for flash programming:
- write_word and write_byte methods have been removed.
- start and end write alignments have been defined.
Moved flash controller registers offsets in a common file
shared with the flash algorithm.
- the flash base address is passed to the flash algorithm
as a parameter.
Removed unused functions
Change-Id: I80aeab3994e477044bbcf02e66d9525dae0cb491
Signed-off-by: luca vinci <luca.vinci@st.com>
Reviewed-on: http://openocd.zylin.com/5393
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Michele Sardo <msmttchr@gmail.com>
Writing bits to an uninitialized buffer generated false warnings.
Zero buffers before setting them by buf_set_u32|64()
(do it only if bit-by-bit copy loop is used,
zeroed buffer is not necessary if a fast path write is used)
Change-Id: I2f7f8ddb45b0cbd08d3e249534fc51f4b5cc6694
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5383
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The aligning code generated a clang static analyzer warning and
imposed huge memory leak. This part of code was removed and
flash infrastructure to alignment is used instead.
Not tested on hw!
Change-Id: I7c71da87547e71d595a7e7071ae5adcc1cecc827
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5367
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Group device list based on the device family and add clear
device family names.
Change-Id: I7a2dab1d1c0c8d141df02656c1964cb2c3fcbcd1
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5423
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this new device has the following features:
- single core cortex-M7
- 2MB flash - dual bank
- page size 8k
- write protection grouped by 4 sectors
- write block size 128 bits (16 bytes)
the bit definition of FLASH_CR is different than STM32H74x,
that's why we introduced a helper to compute the FLASH_CR value
Change-Id: I4da10cde8dd215b1b0f2645f0efdba9d198038d1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5441
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
Change-Id: Ia212b1877abeda27f507de29a3aee2b171c1b8c6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5448
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Also add locking after option write, it was missing at all.
Change-Id: I0227c6a74866f0fe8e40aa58616f0b3115ad5af0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5361
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Report the 32-byte alignemnt requirement via the bank structure rather
than enforcing it ad-hoc in the write routine. This allows people to do
non-32-byte-aligned writes if they want, with the infrastructure fixing
up the addresses passed to the low-level driver.
Change-Id: I2c4f532f2000435954a900224dbc9f2c30d1cc94
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5388
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without this, a failed attempt to change option bytes will silently
appear to succeed but without actually changing the option bytes
(confusingly, the option bytes will still read back as if they had been
changed until a reboot as well!).
Change-Id: Id529c6c384a8a16be75f5702310670d99d8fac79
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5418
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
We have the macro ARRAY_SIZE() already available. Use it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ARRAY_SIZE -f {} \;
Change-Id: Ic7da9b710edf118eacb08f9e222f34208c580842
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5198
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is to avoid confusion with STM32 L4, L4+ and L5 families
also:
- a warning message is changed to error
- stm32l0x and stm32l1x aliases has been created to permit
the usage of either names
Change-Id: If3f16d2a3b7d1369959aa7407da37a9076ea91d7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5437
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This will enable us to use either name when calling flash driver commands.
For example the stm32wbx family use the same flash driver as the stm32l4x, so
the user has to use 'stm32l4x lock 0' which can be confusing.
Now the user can also use 'stm32wbx lock 0' with the same result.
Change-Id: Ic0d8da9afc202d7cc82d9b9949827e958a1cc824
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5436
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add driver for the RPC block in HF mode on Renesas R-Car Gen3 SoCs.
This driver allows operating the on-SIP HF memory.
Note that HF is CFI compliant flash, but it is not memory mapped,
hence the need to replace all the memory accessors and read/write
functions. The write function is entirely replaced to increase
performance and is Spansion/AMD specific, since there is no known
SIP with other HF from another vendor.
Add the following two lines to board TCL file to bind the driver on
R-Car Gen3 SoC using HyperFlash:
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME rpchf 0x08000000 0x4000000 2 2 $_CHIPNAME.a57.0
Change-Id: Ie18729d017eeb46e1363333ffe002d010dfc5ead
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5149
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fix comment of tested errors in asm src.
List all relevant errors in FLASH_ERROR mask: FLASH_PROGERR was missing
and any trial to re-program already programmed double word ended up
in the error bit held uncleared and flash write permanetly repeating
the error message until reset.
Lock the bank also after unsuccesfull write_block run.
Set async target algo block size to size of double word.
Remove warning in case of write_block success. In case of error
use LOG_ERROR instead of warning.
Change-Id: Ibf6d5e306a4c2eaa43de67d636b4902c737f02f3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5360
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The original code paded the write chunk with random bytes by overrunning
the buffer. An user can easily regard the random bytes to
be a programming error.
Change-Id: Ib0f47b5bc406bc6a7c32f3d929bf324a17c7c1e1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5359
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The chip->hwid is uint32_t , fix the print format.
This was detected by TravisCI on OSX, where this triggers a build error.
Change-Id: I776a7bb50e396c8fccc24500dec4750190da7982
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5401
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ilya Kharin <akscram@gmail.com>
Add driver for the SH QSPI controller. This SPI controller is often
connected to the boot SPI NOR flash on R-Car Gen2 platforms.
Add the following two lines to board TCL file to bind the driver on
R-Car Gen2 SoC and make SRAM work area available:
flash bank flash0 sh_qspi 0xe6b10000 0 0 0 ${_TARGETNAME}0 cs0
${_TARGETNAME}0 configure -work-area-phys 0xe6300000 -work-area-virt 0xe6300000 -work-area-size 0x10000 -work-area-backup 0
To install mainline U-Boot on the board, use the following procedure:
proc update_uboot {} {
# SPL
flash erase_sector 0 0x0 0x0
flash write_bank 0 /u-boot/spl/u-boot-spl.bin 0x0
# U-Boot
flash erase_sector 0 0x5 0x6
flash write_bank 0 /u-boot/u-boot.img 0x140000
}
Change-Id: Ief22f61e93bcabae37f6e371156dece6c4be3459
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
V2: - Add Makefile and linker script for the SH QSPI IO algorithm
- Include the algorithm code instead of hard-coding it
Reviewed-on: http://openocd.zylin.com/5143
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This is a preparatory change, align the function name with the rest
of the API, no functional change.
Change-Id: I6a810d2a54edcd13ad9a87d24a7334802c41623b
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5391
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is a preparatory change, align the function name with the rest
of the API, no functional change.
Change-Id: Ib967520f027b03eb1792b36ede52335df8e23941
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5390
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add possibility to supply custom CFI memory accessors via cfi_info
and override the default memory-mapped ones.
Change-Id: I1b6bc1db69fc33e8cdef96c41742c40e6d8917e9
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The size argument is always set to bank->bus_width and bank pointer
is now passed into cfi_target_{read,write}_memory(), so the size
can be accessed through the bank pointer inside the function instead
of being explicitly passed in.
Change-Id: I0abc1cc3bf513281c10cb5de7a21cb0e75cb7676
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5389
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace passing in struct target with passing in struct flash_bank,
so that the later can contain function pointers to custom per-driver
memory accessor functions.
Change-Id: Id2573a6d5f1a73ed9c4f73c53592a9a335a11c99
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5146
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32L4P/Q devices have:
- similar flash layout as STM32L4R/S devices
- 1024K of flash memory (some parts have 512K only)
tested on NUCLEO-L4P5ZG using board/st_nucleo_l4.cfg
Change-Id: I77047351bc7dcd7c76d0f31a77be73005104a06f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5392
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This rework is inspired from the 'flash/nor/stm32h7x.c'
This rework will ease the support of new devices on top of this driver:
for example: STM32WB have different flash base and size addresses
Notes:
- stm32l4_probe modified in order to charge the correct part_info from
the defined stm32l4_parts according to the device id
- stm32l4_flash_bank.bank2_start is replaced by .part_info->bank1_sectors
- STM32_FLASH_BASE is removed , part_info->flash_regs_base will be used instead
based on that flash register addresses are changed to offsets,
>> stm32l4_get_flash_reg was modified accordingly
- stm32l4_read_option and stm32l4_write_option was modified to accept an
offset instead of an absolute address, luckily this is the commands'
argument by default
- stm32l4_mass_erase modifications :
- use MER2 only on top of dual bank devices
- wait for BUSY bit before starting the mass erase
Change-Id: Ib35bfc3cbadc76bbeaaaba9005b82077b9e1e744
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4932
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Create separate memory read/write functions which facilitate access
to the CFI NOR, so that they can be replaced by controller-specific
functions if necessary. This would become necessary when implementing
support for e.g. HyperFlash controllers, which do not directly map
the HyperFlash into the address space.
Change-Id: I1bba1edfd397cb37bfedb43efe2dd03feb26a375
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5145
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Factor out the spansion unlock sequence to deduplicate the code.
Change-Id: Id78522e9a2f0e701870ef816772289d08257476a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5144
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The current code assumes an STM32's flash bank is laid-out in either of
two configurations:
- 4 x 16kB + 1 x 64kB + n x 128kB
- 4 x 32kB + 1 x 128kB + n x 256kB
This is quite ad-hoc but works fine in practice, as long as there are at
least 5 sectors (if n=0). Unfortunately, some newer STM32s are shipping
with only 64 kB of flash (4 x 16kB sectors).
This patch still assumes the same sector layout, but only keeps adding
sectors to the bank if the bank's capacity has not been reached. This
prevents openocd from crashing on some newer STM32s.
Change-Id: If00e5d7a328d11b399babc0bb2111e3ad8a3217e
Signed-off-by: Romain Goyet <romain.goyet@numworks.com>
Signed-off-by: Keir Fraser <keir.xen@gmail.com>
Reviewed-on: http://openocd.zylin.com/4926
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tarek BOCHKATI
Tomas Vanek
Mischa Studer
Rene Kita
Antonio Borneo
Raúl Sanchez Siles
Marc Schink
Tarek BOCHKATI
Luca Lindhorst
Andreas Bolsch
Benedikt-Alexander Mokroß
Christopher Head
Michael Betz
Hellosun Wu
Michael Hope
Alistair Francis
Edward Fewell
Paul Fertser
Ilya Kharin
Aurélien Martin
tscn92
Sasha Kozaruk
Lars Poeschel
luca vinci
Michael Stoll
Frank Hunleth
Marek Vasut
Keir Fraser