yosys/techlibs/gowin/cells_sim.v

(* abc9_lut=1 *)
module LUT1(output F, input I0);
	parameter [1:0] INIT = 0;
	specify
		(I0 => F) = (555, 902);
	endspecify
	assign F = I0 ? INIT[1] : INIT[0];
endmodule

(* abc9_lut=1 *)
module LUT2(output F, input I0, I1);
	parameter [3:0] INIT = 0;
	specify
		(I0 => F) = (867, 1184);
		(I1 => F) = (555, 902);
	endspecify
	wire [ 1: 0] s1 = I1 ? INIT[ 3: 2] : INIT[ 1: 0];
	assign F = I0 ? s1[1] : s1[0];
endmodule

(* abc9_lut=1 *)
module LUT3(output F, input I0, I1, I2);
	parameter [7:0] INIT = 0;
	specify
		(I0 => F) = (1054, 1486);
		(I1 => F) = (867, 1184);
		(I2 => F) = (555, 902);
	endspecify	
	wire [ 3: 0] s2 = I2 ? INIT[ 7: 4] : INIT[ 3: 0];
	wire [ 1: 0] s1 = I1 ?   s2[ 3: 2] :   s2[ 1: 0];
	assign F = I0 ? s1[1] : s1[0];
endmodule

(* abc9_lut=1 *)
module LUT4(output F, input I0, I1, I2, I3);
	parameter [15:0] INIT = 0;
	specify
		(I0 => F) = (1054, 1486);
		(I1 => F) = (1053, 1583);
		(I2 => F) = (867, 1184);
		(I3 => F) = (555, 902);
	endspecify	
	wire [ 7: 0] s3 = I3 ? INIT[15: 8] : INIT[ 7: 0];
	wire [ 3: 0] s2 = I2 ?   s3[ 7: 4] :   s3[ 3: 0];
	wire [ 1: 0] s1 = I1 ?   s2[ 3: 2] :   s2[ 1: 0];
	assign F = I0 ? s1[1] : s1[0];
endmodule

(* abc9_lut=2 *)
module __APICULA_LUT5(output F, input I0, I1, I2, I3, M0);
	specify
		(I0 => F) = (1187, 1638);
		(I1 => F) = (1184, 1638);
		(I2 => F) = (995, 1371);
		(I3 => F) = (808, 1116);
		(M0 => F) = (486, 680);
	endspecify	
endmodule

(* abc9_lut=4 *)
module __APICULA_LUT6(output F, input I0, I1, I2, I3, M0, M1);
	specify
		(I0 => F) = (1187 + 136, 1638 + 255);
		(I1 => F) = (1184 + 136, 1638 + 255);
		(I2 => F) = (995 + 136, 1371 + 255);
		(I3 => F) = (808 + 136, 1116 + 255);
		(M0 => F) = (486 + 136, 680 + 255);
		(M1 => F) = (478, 723);
	endspecify	
endmodule

(* abc9_lut=8 *)
module __APICULA_LUT7(output F, input I0, I1, I2, I3, M0, M1, M2);
	specify
		(I0 => F) = (1187 + 136 + 136, 1638 + 255 + 255);
		(I1 => F) = (1184 + 136 + 136, 1638 + 255 + 255);
		(I2 => F) = (995 + 136 + 136, 1371 + 255 + 255);
		(I3 => F) = (808 + 136 + 136, 1116 + 255 + 255);
		(M0 => F) = (486 + 136 + 136, 680 + 255 + 255);
		(M1 => F) = (478 + 136, 723 + 255);
		(M2 => F) = (478, 723);
	endspecify	
endmodule

(* abc9_lut=16 *)
module __APICULA_LUT8(output F, input I0, I1, I2, I3, M0, M1, M2, M3);
		specify
		(I0 => F) = (1187 + 136 + 136 + 136, 1638 + 255 + 255 + 255);
		(I1 => F) = (1184 + 136 + 136 + 136, 1638 + 255 + 255 + 255);
		(I2 => F) = (995 + 136 + 136 + 136, 1371 + 255 + 255 + 255);
		(I3 => F) = (808 + 136 + 136 + 136, 1116 + 255 + 255 + 255);
		(M0 => F) = (486 + 136 + 136 + 136, 680 + 255 + 255 + 255);
		(M1 => F) = (478 + 136 + 136, 723 + 255 + 255);
		(M2 => F) = (478 + 136, 723 + 255);
		(M3 => F) = (478, 723);
		endspecify	
	endmodule

module MUX2 (O, I0, I1, S0);
  input I0,I1;
  input S0;
  output O;

	specify
		(I0 => O) = (141, 160);
		(I1 => O) = (141, 160);
		(S0 => O) = (486, 680);
	endspecify

  assign O = S0 ? I1 : I0;
endmodule

module MUX2_LUT5 (O, I0, I1, S0);
  input I0,I1;
  input S0;
  output O;

	specify
		(I0 => O) = (141, 160);
		(I1 => O) = (141, 160);
		(S0 => O) = (486, 680);
	endspecify

  MUX2 mux2_lut5 (O, I0, I1, S0);
endmodule

module MUX2_LUT6 (O, I0, I1, S0);
  input I0,I1;
  input S0;
  output O;

	specify
		(I0 => O) = (136, 255);
		(I1 => O) = (136, 255);
		(S0 => O) = (478, 723);
	endspecify

  MUX2 mux2_lut6 (O, I0, I1, S0);
endmodule

module MUX2_LUT7 (O, I0, I1, S0);
  input I0,I1;
  input S0;
  output O;

	specify
		(I0 => O) = (136, 255);
		(I1 => O) = (136, 255);
		(S0 => O) = (478, 723);
	endspecify

  MUX2 mux2_lut7 (O, I0, I1, S0);
endmodule

module MUX2_LUT8 (O, I0, I1, S0);
  input I0,I1;
  input S0;
  output O;

	specify
		(I0 => O) = (136, 255);
		(I1 => O) = (136, 255);
		(S0 => O) = (478, 723);
	endspecify

  MUX2 mux2_lut8 (O, I0, I1, S0);
endmodule

(* abc9_flop, lib_whitebox *)
module DFF (output reg Q, input CLK, D);
	parameter [0:0] INIT = 1'b0;
	initial Q = INIT;

	specify
		(posedge CLK => (Q : D)) = (480, 660);
		$setup(D, posedge CLK, 576);
	endspecify

	always @(posedge CLK)
		Q <= D;
endmodule

(* abc9_flop, lib_whitebox *)
module DFFE (output reg Q, input D, CLK, CE);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		if (CE) (posedge CLK => (Q : D)) = (480, 660);
		$setup(D, posedge CLK &&& CE, 576);
		$setup(CE, posedge CLK, 63);
	endspecify

  always @(posedge CLK) begin
    if (CE)
      Q <= D;
  end
endmodule // DFFE (positive clock edge; clock enable)

(* abc9_box, lib_whitebox *)
module DFFS (output reg Q, input D, CLK, SET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;

	specify
		(posedge CLK => (Q : D)) = (480, 660);
		$setup(D, posedge CLK, 576);
		$setup(SET, posedge CLK, 63);
	endspecify

  always @(posedge CLK) begin
    if (SET)
      Q <= 1'b1;
    else
      Q <= D;	
  end
endmodule // DFFS (positive clock edge; synchronous set)

(* abc9_box, lib_whitebox *)
module DFFSE (output reg Q, input D, CLK, CE, SET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;

	specify
		if (CE) (posedge CLK => (Q : D)) = (480, 660);
		$setup(D, posedge CLK &&& CE, 576);
		$setup(CE, posedge CLK, 63);
		$setup(SET, posedge CLK, 63);
	endspecify

  always @(posedge CLK) begin
    if (SET)
      Q <= 1'b1;
    else if (CE)
      Q <= D;
end
endmodule // DFFSE (positive clock edge; synchronous set takes precedence over clock enable)

(* abc9_flop, lib_whitebox *)
module DFFR (output reg Q, input D, CLK, RESET);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		(posedge CLK => (Q : D)) = (480, 660);
		$setup(D, posedge CLK, 576);
		$setup(RESET, posedge CLK, 63);
	endspecify

  always @(posedge CLK) begin
    if (RESET)
      Q <= 1'b0;
    else
      Q <= D;
  end
endmodule // DFFR (positive clock edge; synchronous reset)

(* abc9_flop, lib_whitebox *)
module DFFRE (output reg Q, input D, CLK, CE, RESET);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		if (CE) (posedge CLK => (Q : D)) = (480, 660);
		$setup(D, posedge CLK &&& CE, 576);
		$setup(CE, posedge CLK, 63);
		$setup(RESET, posedge CLK, 63);
	endspecify

  always @(posedge CLK) begin
    if (RESET)
      Q <= 1'b0;
    else if (CE)
      Q <= D;
  end
endmodule // DFFRE (positive clock edge; synchronous reset takes precedence over clock enable)

(* abc9_box, lib_whitebox *)
module DFFP (output reg Q, input D, CLK, PRESET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;

	specify
		(posedge CLK => (Q : D)) = (480, 660);
		(posedge PRESET => (Q : 1'b1)) = (1800, 2679);
		$setup(D, posedge CLK, 576);
	endspecify

  always @(posedge CLK or posedge PRESET) begin
    if(PRESET)
      Q <= 1'b1;
    else
      Q <= D;
  end
endmodule // DFFP (positive clock edge; asynchronous preset)

(* abc9_box, lib_whitebox *)
module DFFPE (output reg Q, input D, CLK, CE, PRESET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;

	specify
		if (CE) (posedge CLK => (Q : D)) = (480, 660);
		(posedge PRESET => (Q : 1'b1)) = (1800, 2679);
		$setup(D, posedge CLK &&& CE, 576);
		$setup(CE, posedge CLK, 63);
	endspecify

  always @(posedge CLK or posedge PRESET) begin
    if(PRESET)
      Q <= 1'b1;
    else if (CE)
      Q <= D;
  end
endmodule // DFFPE (positive clock edge; asynchronous preset; clock enable)

(* abc9_box, lib_whitebox *)
module DFFC (output reg Q, input D, CLK, CLEAR);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		(posedge CLK => (Q : D)) = (480, 660);
		(posedge CLEAR => (Q : 1'b0)) = (1800, 2679);
		$setup(D, posedge CLK, 576);
	endspecify

  always @(posedge CLK or posedge CLEAR) begin
    if(CLEAR)
      Q <= 1'b0;
    else
      Q <= D;
  end
endmodule // DFFC (positive clock edge; asynchronous clear)

(* abc9_box, lib_whitebox *)
module DFFCE (output reg Q, input D, CLK, CE, CLEAR);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		if (CE) (posedge CLK => (Q : D)) = (480, 660);
		(posedge CLEAR => (Q : 1'b0)) = (1800, 2679);
		$setup(D, posedge CLK &&& CE, 576);
		$setup(CE, posedge CLK, 63);
	endspecify

  always @(posedge CLK or posedge CLEAR) begin
    if(CLEAR)
      Q <= 1'b0;
    else if (CE)
      Q <= D;
  end
endmodule // DFFCE (positive clock edge; asynchronous clear; clock enable)

(* abc9_flop, lib_whitebox *)
module DFFN (output reg Q, input CLK, D);
	parameter [0:0] INIT = 1'b0;
	initial Q = INIT;

  specify
    (negedge CLK => (Q : D)) = (480, 660);
    $setup(D, negedge CLK, 576);
  endspecify

	always @(negedge CLK)
		Q <= D;
endmodule

(* abc9_flop, lib_whitebox *)
module DFFNE (output reg Q, input D, CLK, CE);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		if (CE) (negedge CLK => (Q : D)) = (480, 660);
		$setup(D, negedge CLK &&& CE, 576);
		$setup(CE, negedge CLK, 63);
	endspecify

  always @(negedge CLK) begin
    if (CE)
      Q <= D;
  end
endmodule // DFFNE (negative clock edge; clock enable)

(* abc9_box, lib_whitebox *)
module DFFNS (output reg Q, input D, CLK, SET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;
  
	specify
		(negedge CLK => (Q : D)) = (480, 660);
		$setup(D, negedge CLK, 576);
		$setup(SET, negedge CLK, 63);
	endspecify

  always @(negedge CLK) begin
    if (SET)
      Q <= 1'b1;
    else
      Q <= D;	
  end
endmodule // DFFNS (negative clock edge; synchronous set)

(* abc9_box, lib_whitebox *)
module DFFNSE (output reg Q, input D, CLK, CE, SET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;

	specify
		if (CE) (negedge CLK => (Q : D)) = (480, 660);
		$setup(D, negedge CLK &&& CE, 576);
		$setup(CE, negedge CLK, 63);
		$setup(SET, negedge CLK, 63);
	endspecify

  always @(negedge CLK) begin
    if (SET)
      Q <= 1'b1;
    else if (CE)
      Q <= D;
end
endmodule // DFFNSE (negative clock edge; synchronous set takes precedence over clock enable)

(* abc9_flop, lib_whitebox *)
module DFFNR (output reg Q, input D, CLK, RESET);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		(negedge CLK => (Q : D)) = (480, 660);
		$setup(D, negedge CLK, 576);
		$setup(RESET, negedge CLK, 63);
	endspecify

  always @(negedge CLK) begin
    if (RESET)
      Q <= 1'b0;
    else
      Q <= D;
  end
endmodule // DFFNR (negative clock edge; synchronous reset)

(* abc9_flop, lib_whitebox *)
module DFFNRE (output reg Q, input D, CLK, CE, RESET);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		if (CE) (negedge CLK => (Q : D)) = (480, 660);
		$setup(D, negedge CLK &&& CE, 576);
		$setup(CE, negedge CLK, 63);
		$setup(RESET, negedge CLK, 63);
	endspecify

  always @(negedge CLK) begin
    if (RESET)
      Q <= 1'b0;
    else if (CE)
      Q <= D;
  end
endmodule // DFFNRE (negative clock edge; synchronous reset takes precedence over clock enable)

(* abc9_box, lib_whitebox *)
module DFFNP (output reg Q, input D, CLK, PRESET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;

	specify
		(negedge CLK => (Q : D)) = (480, 660);
		(posedge PRESET => (Q : 1'b1)) = (1800, 2679);
		$setup(D, negedge CLK, 576);
	endspecify

  always @(negedge CLK or posedge PRESET) begin
    if(PRESET)
      Q <= 1'b1;
    else
      Q <= D;
  end
endmodule // DFFNP (negative clock edge; asynchronous preset)

(* abc9_box, lib_whitebox *)
module DFFNPE (output reg Q, input D, CLK, CE, PRESET);
  parameter [0:0] INIT = 1'b1;
  initial Q = INIT;
  
	specify
		if (CE) (negedge CLK => (Q : D)) = (480, 660);
		(posedge PRESET => (Q : 1'b1)) = (1800, 2679);
		$setup(D, negedge CLK &&& CE, 576);
		$setup(CE, negedge CLK, 63);
	endspecify

  always @(negedge CLK or posedge PRESET) begin
    if(PRESET)
      Q <= 1'b1;
    else if (CE)
      Q <= D;
  end
endmodule // DFFNPE (negative clock edge; asynchronous preset; clock enable)

(* abc9_box, lib_whitebox *)
module DFFNC (output reg Q, input D, CLK, CLEAR);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		(negedge CLK => (Q : D)) = (480, 660);
		(posedge CLEAR => (Q : 1'b0)) = (1800, 2679);
		$setup(D, negedge CLK, 576);
	endspecify

  always @(negedge CLK or posedge CLEAR) begin
    if(CLEAR)
      Q <= 1'b0;
    else
      Q <= D;
  end
endmodule // DFFNC (negative clock edge; asynchronous clear)

(* abc9_box, lib_whitebox *)
module DFFNCE (output reg Q, input D, CLK, CE, CLEAR);
  parameter [0:0] INIT = 1'b0;
  initial Q = INIT;

	specify
		if (CE) (negedge CLK => (Q : D)) = (480, 660);
		(posedge CLEAR => (Q : 1'b0)) = (1800, 2679);
		$setup(D, negedge CLK &&& CE, 576);
		$setup(CE, negedge CLK, 63);
	endspecify

  always @(negedge CLK or posedge CLEAR) begin
    if(CLEAR)
      Q <= 1'b0;
    else if (CE)
      Q <= D;
  end
endmodule // DFFNCE (negative clock edge; asynchronous clear; clock enable)

// TODO add more DFF sim cells

module VCC(output V);
	assign V = 1;
endmodule

module GND(output G);
	assign G = 0;
endmodule

module IBUF(output O, input I);

	specify
		(I => O) = 0;
	endspecify

	assign O = I;
endmodule

module OBUF(output O, input I);

	specify
		(I => O) = 0;
	endspecify

	assign O = I;
endmodule

module TBUF (O, I, OEN);
  input I, OEN;
  output O;
  assign O = OEN ? 1'bz : I;
endmodule

module IOBUF (O, IO, I, OEN);
  input I,OEN;
  output O;
  inout IO;
  assign IO = OEN ? 1'bz : I;
  assign I = IO;
endmodule

module ELVDS_OBUF (I, O, OB);
  input I;
  output O;
  output OB;
  assign O = I;
  assign OB = ~I;
endmodule

module TLVDS_OBUF (I, O, OB);
  input I;
  output O;
  output OB;
  assign O = I;
  assign OB = ~I;
endmodule

module OSER4(D3, D2, D1, D0, TX1, TX0, FCLK, PCLK, RESET, Q1, Q0);
	output Q1;
	output Q0;

	input D3;
	input D2;
	input D1;
	input D0;
	input TX1;
	input TX0;
	input FCLK;
	input PCLK;
	input RESET;

	parameter GSREN = "false";
	parameter LSREN = "true";
	parameter TXCLK_POL = 0;
	parameter HWL = "false";
endmodule

module OSER8(D7, D6, D5, D4, D3, D2, D1, D0, TX3, TX2, TX1, TX0, FCLK, PCLK, RESET, Q1, Q0);
	output Q1;
	output Q0;

	input D7;
	input D6;
	input D5;
	input D4;
	input D3;
	input D2;
	input D1;
	input D0;
	input TX3;
	input TX2;
	input TX1;
	input TX0;
	input FCLK;
	input PCLK;
	input RESET;

	parameter GSREN = "false";
	parameter LSREN = "true";
	parameter TXCLK_POL = 0;
	parameter HWL = "false";
endmodule

module OSER10(D9, D8, D7, D6, D5, D4, D3, D2, D1, D0, FCLK, PCLK, RESET, Q);
	output Q;

	input D9;
	input D8;
	input D7;
	input D6;
	input D5;
	input D4;
	input D3;
	input D2;
	input D1;
	input D0;
	input FCLK;
	input PCLK;
	input RESET;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module OVIDEO(D6, D5, D4, D3, D2, D1, D0, FCLK, PCLK, RESET, Q);
	output Q;

	input D6;
	input D5;
	input D4;
	input D3;
	input D2;
	input D1;
	input D0;
	input FCLK;
	input PCLK;
	input RESET;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module OSER16(D15, D14, D13, D12, D11, D10, 
D9, D8, D7, D6, D5, D4, D3, D2, D1, D0, FCLK, PCLK,
RESET, Q);
	output Q;

	input D15;
	input D14;
	input D13;
	input D12;
	input D11;
	input D10;
	input D9;
	input D8;
	input D7;
	input D6;
	input D5;
	input D4;
	input D3;
	input D2;
	input D1;
	input D0;
	input FCLK;
	input PCLK;
	input RESET;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module IDES4(Q3, Q2, Q1, Q0, FCLK, PCLK,
RESET, CALIB, D);
	input D;
	input FCLK;
	input PCLK;
	input RESET;
	input CALIB;

	output Q3;
	output Q2;
	output Q1;
	output Q0;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module IDES8(Q7, Q6, Q5, Q4, Q3, Q2, Q1, Q0, FCLK, PCLK,
RESET, CALIB, D);
	input D;
	input FCLK;
	input PCLK;
	input RESET;
	input CALIB;

	output Q7;
	output Q6;
	output Q5;
	output Q4;
	output Q3;
	output Q2;
	output Q1;
	output Q0;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module IDES10(Q9, Q8, Q7, Q6, Q5, Q4, Q3, Q2, Q1, Q0, FCLK, PCLK,
RESET, CALIB, D);
	input D;
	input FCLK;
	input PCLK;
	input RESET;
	input CALIB;

	output Q9;
	output Q8;
	output Q7;
	output Q6;
	output Q5;
	output Q4;
	output Q3;
	output Q2;
	output Q1;
	output Q0;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module IVIDEO(Q6, Q5, Q4, Q3, Q2, Q1, Q0, FCLK, PCLK,
RESET, CALIB, D);
	input D;
	input FCLK;
	input PCLK;
	input RESET;
	input CALIB;

	output Q6;
	output Q5;
	output Q4;
	output Q3;
	output Q2;
	output Q1;
	output Q0;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module IDES16(Q15, Q14, Q13, Q12, Q11, Q10, 
Q9, Q8, Q7, Q6, Q5, Q4, Q3, Q2, Q1, Q0, FCLK, PCLK,
RESET, CALIB, D);
	input D;
	input FCLK;
	input PCLK;
	input RESET;
	input CALIB;

	output Q15;
	output Q14;
	output Q13;
	output Q12;
	output Q11;
	output Q10;
	output Q9;
	output Q8;
	output Q7;
	output Q6;
	output Q5;
	output Q4;
	output Q3;
	output Q2;
	output Q1;
	output Q0;

	parameter GSREN = "false";
	parameter LSREN = "true";
endmodule

module IDDR(D, CLK, Q0, Q1);
	input D;
	input CLK;
	output Q0;
	output Q1;
	parameter Q0_INIT = 1'b0;
	parameter Q1_INIT = 1'b0;
endmodule

module IDDRC(D, CLK, CLEAR, Q0, Q1);
	input D;
	input CLK;
	input CLEAR;
	output Q0;
	output Q1;
	parameter Q0_INIT = 1'b0;
	parameter Q1_INIT = 1'b0;
endmodule

(* blackbox *)
module ODDR(D0, D1, TX, CLK, Q0, Q1);
	input D0;
	input D1;
	input TX;
	input CLK;
	output Q0;
	output Q1;
	parameter TXCLK_POL = 0;
	parameter INIT = 0;
endmodule

(* blackbox *)
module ODDRC(D0, D1, CLEAR, TX, CLK, Q0, Q1);
	input D0;
	input D1;
	input CLEAR;
	input TX;
	input CLK;
	output Q0;
	output Q1;
	parameter TXCLK_POL = 0;
	parameter INIT = 0;
endmodule

module GSR (input GSRI);
	wire GSRO = GSRI;
endmodule

(* abc9_box, lib_whitebox *)
module ALU (SUM, COUT, I0, I1, I3, CIN);

input I0;
input I1;
input I3;
(* abc9_carry *) input CIN;
output SUM;
(* abc9_carry *) output COUT;

localparam ADD = 0;
localparam SUB = 1;
localparam ADDSUB = 2;
localparam NE = 3;
localparam GE = 4;
localparam LE = 5;
localparam CUP = 6;
localparam CDN = 7;
localparam CUPCDN = 8;
localparam MULT = 9;

parameter ALU_MODE = 0;

reg S, C;

specify
	(I0 => SUM) = (1043, 1432);
	(I1 => SUM) = (775, 1049);
	(I3 => SUM) = (751, 1010);
	(CIN => SUM) = (694, 811);
	(I0  => COUT) = (1010, 1380);
	(I1  => COUT) = (1021, 1505);
	(I3  => COUT) = (483, 792);
	(CIN => COUT) = (49, 82);
endspecify

assign SUM = S ^ CIN;
assign COUT = S? CIN : C;

always @* begin
	case (ALU_MODE)
		ADD: begin
			S = I0 ^ I1;
			C = I0;
		end
		SUB: begin
			S = I0 ^ ~I1;
			C = I0;
		end
		ADDSUB: begin
			S = I3? I0 ^ I1 : I0 ^ ~I1;
			C = I0;
		end
		NE: begin
			S = I0 ^ ~I1;
			C = 1'b1;
		end
		GE: begin
			S = I0 ^ ~I1;
			C = I0;
		end
		LE: begin
			S = ~I0 ^ I1;
			C = I1;
		end
		CUP: begin
			S = I0;
			C = 1'b0;
		end
		CDN: begin
			S = ~I0;
			C = 1'b1;
		end
		CUPCDN: begin
			S = I3? I0 : ~I0;
			C = I0;
		end
		MULT: begin
			S = I0 & I1;
			C = I0 & I1;
		end
	endcase
end

endmodule


module RAM16S1 (DO, DI, AD, WRE, CLK);

parameter INIT_0 = 16'h0000;

input [3:0] AD;
input DI;
output DO;
input CLK;
input WRE;

specify
	(AD *> DO) = (270, 405);
	$setup(DI, posedge CLK, 62);
	$setup(WRE, posedge CLK, 62);
	$setup(AD, posedge CLK, 62);
	(posedge CLK => (DO : 1'bx)) = (474, 565);
endspecify

reg [15:0] mem;

initial begin
	mem = INIT_0;
end

assign DO = mem[AD];

always @(posedge CLK) begin
	if (WRE) begin
		mem[AD] <= DI;
	end
end

endmodule


module RAM16S2 (DO, DI, AD, WRE, CLK);

parameter INIT_0 = 16'h0000;
parameter INIT_1 = 16'h0000;

input [3:0] AD;
input [1:0] DI;
output [1:0] DO;
input CLK;
input WRE;

specify
	(AD *> DO) = (270, 405);
	$setup(DI, posedge CLK, 62);
	$setup(WRE, posedge CLK, 62);
	$setup(AD, posedge CLK, 62);
	(posedge CLK => (DO : 2'bx)) = (474, 565);
endspecify

reg [15:0] mem0, mem1;

initial begin
	mem0 = INIT_0;
	mem1 = INIT_1;
end

assign DO[0] = mem0[AD];
assign DO[1] = mem1[AD];

always @(posedge CLK) begin
	if (WRE) begin
		mem0[AD] <= DI[0];
		mem1[AD] <= DI[1];
	end
end

endmodule


module RAM16S4 (DO, DI, AD, WRE, CLK);

parameter INIT_0 = 16'h0000;
parameter INIT_1 = 16'h0000;
parameter INIT_2 = 16'h0000;
parameter INIT_3 = 16'h0000;

input [3:0] AD;
input [3:0] DI;
output [3:0] DO;
input CLK;
input WRE;

specify
	(AD *> DO) = (270, 405);
	$setup(DI, posedge CLK, 62);
	$setup(WRE, posedge CLK, 62);
	$setup(AD, posedge CLK, 62);
	(posedge CLK => (DO : 4'bx)) = (474, 565);
endspecify

reg [15:0] mem0, mem1, mem2, mem3;

initial begin
	mem0 = INIT_0;
	mem1 = INIT_1;
	mem2 = INIT_2;
	mem3 = INIT_3;
end

assign DO[0] = mem0[AD];
assign DO[1] = mem1[AD];
assign DO[2] = mem2[AD];
assign DO[3] = mem3[AD];

always @(posedge CLK) begin
	if (WRE) begin
		mem0[AD] <= DI[0];
		mem1[AD] <= DI[1];
		mem2[AD] <= DI[2];
		mem3[AD] <= DI[3];
	end
end

endmodule


module RAM16SDP1 (DO, DI, WAD, RAD, WRE, CLK);

parameter INIT_0 = 16'h0000;

input [3:0] WAD;
input [3:0] RAD;
input DI;
output DO;
input CLK;
input WRE;

specify
	(RAD *> DO) = (270, 405);
	$setup(DI, posedge CLK, 62);
	$setup(WRE, posedge CLK, 62);
	$setup(WAD, posedge CLK, 62);
	(posedge CLK => (DO : 1'bx)) = (474, 565);
endspecify

reg [15:0] mem;

initial begin
	mem = INIT_0;
end

assign DO = mem[RAD];

always @(posedge CLK) begin
	if (WRE) begin
		mem[WAD] <= DI;
	end
end

endmodule


module RAM16SDP2 (DO, DI, WAD, RAD, WRE, CLK);

parameter INIT_0 = 16'h0000;
parameter INIT_1 = 16'h0000;

input [3:0] WAD;
input [3:0] RAD;
input [1:0] DI;
output [1:0] DO;
input CLK;
input WRE;

specify
	(RAD *> DO) = (270, 405);
	$setup(DI, posedge CLK, 62);
	$setup(WRE, posedge CLK, 62);
	$setup(WAD, posedge CLK, 62);
	(posedge CLK => (DO : 2'bx)) = (474, 565);
endspecify

reg [15:0] mem0, mem1;

initial begin
	mem0 = INIT_0;
	mem1 = INIT_1;
end

assign DO[0] = mem0[RAD];
assign DO[1] = mem1[RAD];

always @(posedge CLK) begin
	if (WRE) begin
		mem0[WAD] <= DI[0];
		mem1[WAD] <= DI[1];
	end
end

endmodule


module RAM16SDP4 (DO, DI, WAD, RAD, WRE, CLK);

parameter INIT_0 = 16'h0000;
parameter INIT_1 = 16'h0000;
parameter INIT_2 = 16'h0000;
parameter INIT_3 = 16'h0000;

input [3:0] WAD;
input [3:0] RAD;
input [3:0] DI;
output [3:0] DO;
input CLK;
input WRE;

specify
	(RAD *> DO) = (270, 405);
	$setup(DI, posedge CLK, 62);
	$setup(WRE, posedge CLK, 62);
	$setup(WAD, posedge CLK, 62);
	(posedge CLK => (DO : 4'bx)) = (474, 565);
endspecify

reg [15:0] mem0, mem1, mem2, mem3;

initial begin
	mem0 = INIT_0;
	mem1 = INIT_1;
	mem2 = INIT_2;
	mem3 = INIT_3;
end

assign DO[0] = mem0[RAD];
assign DO[1] = mem1[RAD];
assign DO[2] = mem2[RAD];
assign DO[3] = mem3[RAD];

always @(posedge CLK) begin
	if (WRE) begin
		mem0[WAD] <= DI[0];
		mem1[WAD] <= DI[1];
		mem2[WAD] <= DI[2];
		mem3[WAD] <= DI[3];
	end
end

endmodule


(* blackbox *)
module SP (DO, DI, BLKSEL, AD, WRE, CLK, CE, OCE, RESET);

// 1 Enables output pipeline registers.
parameter READ_MODE = 1'b0;
// 0: no read on write, 1: transparent, 2: read-before-write
parameter WRITE_MODE = 2'b00;
parameter BIT_WIDTH = 32; // 1, 2, 4, 8, 16, 32
parameter BLK_SEL = 3'b000;
parameter RESET_MODE = "SYNC";
parameter INIT_RAM_00 = 256'h0;
parameter INIT_RAM_01 = 256'h0;
parameter INIT_RAM_02 = 256'h0;
parameter INIT_RAM_03 = 256'h0;
parameter INIT_RAM_04 = 256'h0;
parameter INIT_RAM_05 = 256'h0;
parameter INIT_RAM_06 = 256'h0;
parameter INIT_RAM_07 = 256'h0;
parameter INIT_RAM_08 = 256'h0;
parameter INIT_RAM_09 = 256'h0;
parameter INIT_RAM_0A = 256'h0;
parameter INIT_RAM_0B = 256'h0;
parameter INIT_RAM_0C = 256'h0;
parameter INIT_RAM_0D = 256'h0;
parameter INIT_RAM_0E = 256'h0;
parameter INIT_RAM_0F = 256'h0;
parameter INIT_RAM_10 = 256'h0;
parameter INIT_RAM_11 = 256'h0;
parameter INIT_RAM_12 = 256'h0;
parameter INIT_RAM_13 = 256'h0;
parameter INIT_RAM_14 = 256'h0;
parameter INIT_RAM_15 = 256'h0;
parameter INIT_RAM_16 = 256'h0;
parameter INIT_RAM_17 = 256'h0;
parameter INIT_RAM_18 = 256'h0;
parameter INIT_RAM_19 = 256'h0;
parameter INIT_RAM_1A = 256'h0;
parameter INIT_RAM_1B = 256'h0;
parameter INIT_RAM_1C = 256'h0;
parameter INIT_RAM_1D = 256'h0;
parameter INIT_RAM_1E = 256'h0;
parameter INIT_RAM_1F = 256'h0;
parameter INIT_RAM_20 = 256'h0;
parameter INIT_RAM_21 = 256'h0;
parameter INIT_RAM_22 = 256'h0;
parameter INIT_RAM_23 = 256'h0;
parameter INIT_RAM_24 = 256'h0;
parameter INIT_RAM_25 = 256'h0;
parameter INIT_RAM_26 = 256'h0;
parameter INIT_RAM_27 = 256'h0;
parameter INIT_RAM_28 = 256'h0;
parameter INIT_RAM_29 = 256'h0;
parameter INIT_RAM_2A = 256'h0;
parameter INIT_RAM_2B = 256'h0;
parameter INIT_RAM_2C = 256'h0;
parameter INIT_RAM_2D = 256'h0;
parameter INIT_RAM_2E = 256'h0;
parameter INIT_RAM_2F = 256'h0;
parameter INIT_RAM_30 = 256'h0;
parameter INIT_RAM_31 = 256'h0;
parameter INIT_RAM_32 = 256'h0;
parameter INIT_RAM_33 = 256'h0;
parameter INIT_RAM_34 = 256'h0;
parameter INIT_RAM_35 = 256'h0;
parameter INIT_RAM_36 = 256'h0;
parameter INIT_RAM_37 = 256'h0;
parameter INIT_RAM_38 = 256'h0;
parameter INIT_RAM_39 = 256'h0;
parameter INIT_RAM_3A = 256'h0;
parameter INIT_RAM_3B = 256'h0;
parameter INIT_RAM_3C = 256'h0;
parameter INIT_RAM_3D = 256'h0;
parameter INIT_RAM_3E = 256'h0;
parameter INIT_RAM_3F = 256'h0;

output [31:0] DO;
input [31:0] DI;
input [2:0] BLKSEL;
input [13:0] AD;
input WRE;
input CLK;
input CE;
input OCE;
input RESET;

endmodule

(* blackbox *)
module SPX9 (DO, DI, BLKSEL, AD, WRE, CLK, CE, OCE, RESET);

// 1 Enables output pipeline registers.
parameter READ_MODE = 1'b0;
// 0: no read on write, 1: transparent, 2: read-before-write
parameter WRITE_MODE = 2'b00;
parameter BIT_WIDTH = 36; // 9, 18, 36
parameter BLK_SEL = 3'b000;
parameter RESET_MODE = "SYNC";
parameter INIT_RAM_00 = 288'h0;
parameter INIT_RAM_01 = 288'h0;
parameter INIT_RAM_02 = 288'h0;
parameter INIT_RAM_03 = 288'h0;
parameter INIT_RAM_04 = 288'h0;
parameter INIT_RAM_05 = 288'h0;
parameter INIT_RAM_06 = 288'h0;
parameter INIT_RAM_07 = 288'h0;
parameter INIT_RAM_08 = 288'h0;
parameter INIT_RAM_09 = 288'h0;
parameter INIT_RAM_0A = 288'h0;
parameter INIT_RAM_0B = 288'h0;
parameter INIT_RAM_0C = 288'h0;
parameter INIT_RAM_0D = 288'h0;
parameter INIT_RAM_0E = 288'h0;
parameter INIT_RAM_0F = 288'h0;
parameter INIT_RAM_10 = 288'h0;
parameter INIT_RAM_11 = 288'h0;
parameter INIT_RAM_12 = 288'h0;
parameter INIT_RAM_13 = 288'h0;
parameter INIT_RAM_14 = 288'h0;
parameter INIT_RAM_15 = 288'h0;
parameter INIT_RAM_16 = 288'h0;
parameter INIT_RAM_17 = 288'h0;
parameter INIT_RAM_18 = 288'h0;
parameter INIT_RAM_19 = 288'h0;
parameter INIT_RAM_1A = 288'h0;
parameter INIT_RAM_1B = 288'h0;
parameter INIT_RAM_1C = 288'h0;
parameter INIT_RAM_1D = 288'h0;
parameter INIT_RAM_1E = 288'h0;
parameter INIT_RAM_1F = 288'h0;
parameter INIT_RAM_20 = 288'h0;
parameter INIT_RAM_21 = 288'h0;
parameter INIT_RAM_22 = 288'h0;
parameter INIT_RAM_23 = 288'h0;
parameter INIT_RAM_24 = 288'h0;
parameter INIT_RAM_25 = 288'h0;
parameter INIT_RAM_26 = 288'h0;
parameter INIT_RAM_27 = 288'h0;
parameter INIT_RAM_28 = 288'h0;
parameter INIT_RAM_29 = 288'h0;
parameter INIT_RAM_2A = 288'h0;
parameter INIT_RAM_2B = 288'h0;
parameter INIT_RAM_2C = 288'h0;
parameter INIT_RAM_2D = 288'h0;
parameter INIT_RAM_2E = 288'h0;
parameter INIT_RAM_2F = 288'h0;
parameter INIT_RAM_30 = 288'h0;
parameter INIT_RAM_31 = 288'h0;
parameter INIT_RAM_32 = 288'h0;
parameter INIT_RAM_33 = 288'h0;
parameter INIT_RAM_34 = 288'h0;
parameter INIT_RAM_35 = 288'h0;
parameter INIT_RAM_36 = 288'h0;
parameter INIT_RAM_37 = 288'h0;
parameter INIT_RAM_38 = 288'h0;
parameter INIT_RAM_39 = 288'h0;
parameter INIT_RAM_3A = 288'h0;
parameter INIT_RAM_3B = 288'h0;
parameter INIT_RAM_3C = 288'h0;
parameter INIT_RAM_3D = 288'h0;
parameter INIT_RAM_3E = 288'h0;
parameter INIT_RAM_3F = 288'h0;

output [35:0] DO;
input [35:0] DI;
input [2:0] BLKSEL;
input [13:0] AD;
input WRE;
input CLK;
input CE;
input OCE;
input RESET;

endmodule


(* blackbox *)
module SDP (DO, DI, BLKSEL, ADA, ADB, WREA, WREB, CLKA, CLKB, CEA, CEB, OCE, RESETA, RESETB);

parameter READ_MODE = 1'b0;
parameter BIT_WIDTH_0 = 32; // 1, 2, 4, 8, 16, 32
parameter BIT_WIDTH_1 = 32; // 1, 2, 4, 8, 16, 32
parameter BLK_SEL = 3'b000;
parameter RESET_MODE = "SYNC";
parameter INIT_RAM_00 = 256'h0;
parameter INIT_RAM_01 = 256'h0;
parameter INIT_RAM_02 = 256'h0;
parameter INIT_RAM_03 = 256'h0;
parameter INIT_RAM_04 = 256'h0;
parameter INIT_RAM_05 = 256'h0;
parameter INIT_RAM_06 = 256'h0;
parameter INIT_RAM_07 = 256'h0;
parameter INIT_RAM_08 = 256'h0;
parameter INIT_RAM_09 = 256'h0;
parameter INIT_RAM_0A = 256'h0;
parameter INIT_RAM_0B = 256'h0;
parameter INIT_RAM_0C = 256'h0;
parameter INIT_RAM_0D = 256'h0;
parameter INIT_RAM_0E = 256'h0;
parameter INIT_RAM_0F = 256'h0;
parameter INIT_RAM_10 = 256'h0;
parameter INIT_RAM_11 = 256'h0;
parameter INIT_RAM_12 = 256'h0;
parameter INIT_RAM_13 = 256'h0;
parameter INIT_RAM_14 = 256'h0;
parameter INIT_RAM_15 = 256'h0;
parameter INIT_RAM_16 = 256'h0;
parameter INIT_RAM_17 = 256'h0;
parameter INIT_RAM_18 = 256'h0;
parameter INIT_RAM_19 = 256'h0;
parameter INIT_RAM_1A = 256'h0;
parameter INIT_RAM_1B = 256'h0;
parameter INIT_RAM_1C = 256'h0;
parameter INIT_RAM_1D = 256'h0;
parameter INIT_RAM_1E = 256'h0;
parameter INIT_RAM_1F = 256'h0;
parameter INIT_RAM_20 = 256'h0;
parameter INIT_RAM_21 = 256'h0;
parameter INIT_RAM_22 = 256'h0;
parameter INIT_RAM_23 = 256'h0;
parameter INIT_RAM_24 = 256'h0;
parameter INIT_RAM_25 = 256'h0;
parameter INIT_RAM_26 = 256'h0;
parameter INIT_RAM_27 = 256'h0;
parameter INIT_RAM_28 = 256'h0;
parameter INIT_RAM_29 = 256'h0;
parameter INIT_RAM_2A = 256'h0;
parameter INIT_RAM_2B = 256'h0;
parameter INIT_RAM_2C = 256'h0;
parameter INIT_RAM_2D = 256'h0;
parameter INIT_RAM_2E = 256'h0;
parameter INIT_RAM_2F = 256'h0;
parameter INIT_RAM_30 = 256'h0;
parameter INIT_RAM_31 = 256'h0;
parameter INIT_RAM_32 = 256'h0;
parameter INIT_RAM_33 = 256'h0;
parameter INIT_RAM_34 = 256'h0;
parameter INIT_RAM_35 = 256'h0;
parameter INIT_RAM_36 = 256'h0;
parameter INIT_RAM_37 = 256'h0;
parameter INIT_RAM_38 = 256'h0;
parameter INIT_RAM_39 = 256'h0;
parameter INIT_RAM_3A = 256'h0;
parameter INIT_RAM_3B = 256'h0;
parameter INIT_RAM_3C = 256'h0;
parameter INIT_RAM_3D = 256'h0;
parameter INIT_RAM_3E = 256'h0;
parameter INIT_RAM_3F = 256'h0;

output [31:0] DO;
input [31:0] DI;
input [2:0] BLKSEL;
input [13:0] ADA, ADB;
input WREA, WREB;
input CLKA, CLKB;
input CEA, CEB;
input OCE;
input RESETA, RESETB;

specify
	(posedge CLKB => (DO : DI)) = (419, 493);
	$setup(RESETA, posedge CLKA, 62);
	$setup(RESETB, posedge CLKB, 62);
	$setup(OCE, posedge CLKB, 62);
	$setup(CEA, posedge CLKA, 62);
	$setup(CEB, posedge CLKB, 62);
	$setup(OCE, posedge CLKB, 62);
	$setup(WREA, posedge CLKA, 62);
	$setup(WREB, posedge CLKB, 62);
	$setup(DI, posedge CLKA, 62);
	$setup(ADA, posedge CLKA, 62);
	$setup(ADB, posedge CLKB, 62);
	$setup(BLKSEL, posedge CLKA, 62);
endspecify

endmodule

(* blackbox *)
module SDPX9 (DO, DI, BLKSEL, ADA, ADB, WREA, WREB, CLKA, CLKB, CEA, CEB, OCE, RESETA, RESETB);

parameter READ_MODE = 1'b0;
parameter BIT_WIDTH_0 = 36; // 9, 18, 36
parameter BIT_WIDTH_1 = 36; // 9, 18, 36
parameter BLK_SEL = 3'b000;
parameter RESET_MODE = "SYNC";
parameter INIT_RAM_00 = 288'h0;
parameter INIT_RAM_01 = 288'h0;
parameter INIT_RAM_02 = 288'h0;
parameter INIT_RAM_03 = 288'h0;
parameter INIT_RAM_04 = 288'h0;
parameter INIT_RAM_05 = 288'h0;
parameter INIT_RAM_06 = 288'h0;
parameter INIT_RAM_07 = 288'h0;
parameter INIT_RAM_08 = 288'h0;
parameter INIT_RAM_09 = 288'h0;
parameter INIT_RAM_0A = 288'h0;
parameter INIT_RAM_0B = 288'h0;
parameter INIT_RAM_0C = 288'h0;
parameter INIT_RAM_0D = 288'h0;
parameter INIT_RAM_0E = 288'h0;
parameter INIT_RAM_0F = 288'h0;
parameter INIT_RAM_10 = 288'h0;
parameter INIT_RAM_11 = 288'h0;
parameter INIT_RAM_12 = 288'h0;
parameter INIT_RAM_13 = 288'h0;
parameter INIT_RAM_14 = 288'h0;
parameter INIT_RAM_15 = 288'h0;
parameter INIT_RAM_16 = 288'h0;
parameter INIT_RAM_17 = 288'h0;
parameter INIT_RAM_18 = 288'h0;
parameter INIT_RAM_19 = 288'h0;
parameter INIT_RAM_1A = 288'h0;
parameter INIT_RAM_1B = 288'h0;
parameter INIT_RAM_1C = 288'h0;
parameter INIT_RAM_1D = 288'h0;
parameter INIT_RAM_1E = 288'h0;
parameter INIT_RAM_1F = 288'h0;
parameter INIT_RAM_20 = 288'h0;
parameter INIT_RAM_21 = 288'h0;
parameter INIT_RAM_22 = 288'h0;
parameter INIT_RAM_23 = 288'h0;
parameter INIT_RAM_24 = 288'h0;
parameter INIT_RAM_25 = 288'h0;
parameter INIT_RAM_26 = 288'h0;
parameter INIT_RAM_27 = 288'h0;
parameter INIT_RAM_28 = 288'h0;
parameter INIT_RAM_29 = 288'h0;
parameter INIT_RAM_2A = 288'h0;
parameter INIT_RAM_2B = 288'h0;
parameter INIT_RAM_2C = 288'h0;
parameter INIT_RAM_2D = 288'h0;
parameter INIT_RAM_2E = 288'h0;
parameter INIT_RAM_2F = 288'h0;
parameter INIT_RAM_30 = 288'h0;
parameter INIT_RAM_31 = 288'h0;
parameter INIT_RAM_32 = 288'h0;
parameter INIT_RAM_33 = 288'h0;
parameter INIT_RAM_34 = 288'h0;
parameter INIT_RAM_35 = 288'h0;
parameter INIT_RAM_36 = 288'h0;
parameter INIT_RAM_37 = 288'h0;
parameter INIT_RAM_38 = 288'h0;
parameter INIT_RAM_39 = 288'h0;
parameter INIT_RAM_3A = 288'h0;
parameter INIT_RAM_3B = 288'h0;
parameter INIT_RAM_3C = 288'h0;
parameter INIT_RAM_3D = 288'h0;
parameter INIT_RAM_3E = 288'h0;
parameter INIT_RAM_3F = 288'h0;

output [35:0] DO;
input [35:0] DI;
input [2:0] BLKSEL;
input [13:0] ADA, ADB;
input WREA, WREB;
input CLKA, CLKB;
input CEA, CEB;
input OCE;
input RESETA, RESETB;

specify
	(posedge CLKB => (DO : DI)) = (419, 493);
	$setup(RESETA, posedge CLKA, 62);
	$setup(RESETB, posedge CLKB, 62);
	$setup(OCE, posedge CLKB, 62);
	$setup(CEA, posedge CLKA, 62);
	$setup(CEB, posedge CLKB, 62);
	$setup(OCE, posedge CLKB, 62);
	$setup(WREA, posedge CLKA, 62);
	$setup(WREB, posedge CLKB, 62);
	$setup(DI, posedge CLKA, 62);
	$setup(ADA, posedge CLKA, 62);
	$setup(ADB, posedge CLKB, 62);
	$setup(BLKSEL, posedge CLKA, 62);
endspecify

endmodule


(* blackbox *)
module DP (DOA, DOB, DIA, DIB, BLKSEL, ADA, ADB, WREA, WREB, CLKA, CLKB, CEA, CEB, OCEA, OCEB, RESETA, RESETB);

parameter READ_MODE0 = 1'b0;
parameter READ_MODE1 = 1'b0;
parameter WRITE_MODE0 = 2'b00;
parameter WRITE_MODE1 = 2'b00;
parameter BIT_WIDTH_0 = 16; // 1, 2, 4, 8, 16
parameter BIT_WIDTH_1 = 16; // 1, 2, 4, 8, 16
parameter BLK_SEL = 3'b000;
parameter RESET_MODE = "SYNC";
parameter INIT_RAM_00 = 256'h0;
parameter INIT_RAM_01 = 256'h0;
parameter INIT_RAM_02 = 256'h0;
parameter INIT_RAM_03 = 256'h0;
parameter INIT_RAM_04 = 256'h0;
parameter INIT_RAM_05 = 256'h0;
parameter INIT_RAM_06 = 256'h0;
parameter INIT_RAM_07 = 256'h0;
parameter INIT_RAM_08 = 256'h0;
parameter INIT_RAM_09 = 256'h0;
parameter INIT_RAM_0A = 256'h0;
parameter INIT_RAM_0B = 256'h0;
parameter INIT_RAM_0C = 256'h0;
parameter INIT_RAM_0D = 256'h0;
parameter INIT_RAM_0E = 256'h0;
parameter INIT_RAM_0F = 256'h0;
parameter INIT_RAM_10 = 256'h0;
parameter INIT_RAM_11 = 256'h0;
parameter INIT_RAM_12 = 256'h0;
parameter INIT_RAM_13 = 256'h0;
parameter INIT_RAM_14 = 256'h0;
parameter INIT_RAM_15 = 256'h0;
parameter INIT_RAM_16 = 256'h0;
parameter INIT_RAM_17 = 256'h0;
parameter INIT_RAM_18 = 256'h0;
parameter INIT_RAM_19 = 256'h0;
parameter INIT_RAM_1A = 256'h0;
parameter INIT_RAM_1B = 256'h0;
parameter INIT_RAM_1C = 256'h0;
parameter INIT_RAM_1D = 256'h0;
parameter INIT_RAM_1E = 256'h0;
parameter INIT_RAM_1F = 256'h0;
parameter INIT_RAM_20 = 256'h0;
parameter INIT_RAM_21 = 256'h0;
parameter INIT_RAM_22 = 256'h0;
parameter INIT_RAM_23 = 256'h0;
parameter INIT_RAM_24 = 256'h0;
parameter INIT_RAM_25 = 256'h0;
parameter INIT_RAM_26 = 256'h0;
parameter INIT_RAM_27 = 256'h0;
parameter INIT_RAM_28 = 256'h0;
parameter INIT_RAM_29 = 256'h0;
parameter INIT_RAM_2A = 256'h0;
parameter INIT_RAM_2B = 256'h0;
parameter INIT_RAM_2C = 256'h0;
parameter INIT_RAM_2D = 256'h0;
parameter INIT_RAM_2E = 256'h0;
parameter INIT_RAM_2F = 256'h0;
parameter INIT_RAM_30 = 256'h0;
parameter INIT_RAM_31 = 256'h0;
parameter INIT_RAM_32 = 256'h0;
parameter INIT_RAM_33 = 256'h0;
parameter INIT_RAM_34 = 256'h0;
parameter INIT_RAM_35 = 256'h0;
parameter INIT_RAM_36 = 256'h0;
parameter INIT_RAM_37 = 256'h0;
parameter INIT_RAM_38 = 256'h0;
parameter INIT_RAM_39 = 256'h0;
parameter INIT_RAM_3A = 256'h0;
parameter INIT_RAM_3B = 256'h0;
parameter INIT_RAM_3C = 256'h0;
parameter INIT_RAM_3D = 256'h0;
parameter INIT_RAM_3E = 256'h0;
parameter INIT_RAM_3F = 256'h0;

output [15:0] DOA, DOB;
input [15:0] DIA, DIB;
input [2:0] BLKSEL;
input [13:0] ADA, ADB;
input WREA, WREB;
input CLKA, CLKB;
input CEA, CEB;
input OCEA, OCEB;
input RESETA, RESETB;

endmodule

(* blackbox *)
module DPX9 (DOA, DOB, DIA, DIB, BLKSEL, ADA, ADB, WREA, WREB, CLKA, CLKB, CEA, CEB, OCEA, OCEB, RESETA, RESETB);

parameter READ_MODE0 = 1'b0;
parameter READ_MODE1 = 1'b0;
parameter WRITE_MODE0 = 2'b00;
parameter WRITE_MODE1 = 2'b00;
parameter BIT_WIDTH_0 = 18; // 9, 18
parameter BIT_WIDTH_1 = 18; // 9, 18
parameter BLK_SEL = 3'b000;
parameter RESET_MODE = "SYNC";
parameter INIT_RAM_00 = 288'h0;
parameter INIT_RAM_01 = 288'h0;
parameter INIT_RAM_02 = 288'h0;
parameter INIT_RAM_03 = 288'h0;
parameter INIT_RAM_04 = 288'h0;
parameter INIT_RAM_05 = 288'h0;
parameter INIT_RAM_06 = 288'h0;
parameter INIT_RAM_07 = 288'h0;
parameter INIT_RAM_08 = 288'h0;
parameter INIT_RAM_09 = 288'h0;
parameter INIT_RAM_0A = 288'h0;
parameter INIT_RAM_0B = 288'h0;
parameter INIT_RAM_0C = 288'h0;
parameter INIT_RAM_0D = 288'h0;
parameter INIT_RAM_0E = 288'h0;
parameter INIT_RAM_0F = 288'h0;
parameter INIT_RAM_10 = 288'h0;
parameter INIT_RAM_11 = 288'h0;
parameter INIT_RAM_12 = 288'h0;
parameter INIT_RAM_13 = 288'h0;
parameter INIT_RAM_14 = 288'h0;
parameter INIT_RAM_15 = 288'h0;
parameter INIT_RAM_16 = 288'h0;
parameter INIT_RAM_17 = 288'h0;
parameter INIT_RAM_18 = 288'h0;
parameter INIT_RAM_19 = 288'h0;
parameter INIT_RAM_1A = 288'h0;
parameter INIT_RAM_1B = 288'h0;
parameter INIT_RAM_1C = 288'h0;
parameter INIT_RAM_1D = 288'h0;
parameter INIT_RAM_1E = 288'h0;
parameter INIT_RAM_1F = 288'h0;
parameter INIT_RAM_20 = 288'h0;
parameter INIT_RAM_21 = 288'h0;
parameter INIT_RAM_22 = 288'h0;
parameter INIT_RAM_23 = 288'h0;
parameter INIT_RAM_24 = 288'h0;
parameter INIT_RAM_25 = 288'h0;
parameter INIT_RAM_26 = 288'h0;
parameter INIT_RAM_27 = 288'h0;
parameter INIT_RAM_28 = 288'h0;
parameter INIT_RAM_29 = 288'h0;
parameter INIT_RAM_2A = 288'h0;
parameter INIT_RAM_2B = 288'h0;
parameter INIT_RAM_2C = 288'h0;
parameter INIT_RAM_2D = 288'h0;
parameter INIT_RAM_2E = 288'h0;
parameter INIT_RAM_2F = 288'h0;
parameter INIT_RAM_30 = 288'h0;
parameter INIT_RAM_31 = 288'h0;
parameter INIT_RAM_32 = 288'h0;
parameter INIT_RAM_33 = 288'h0;
parameter INIT_RAM_34 = 288'h0;
parameter INIT_RAM_35 = 288'h0;
parameter INIT_RAM_36 = 288'h0;
parameter INIT_RAM_37 = 288'h0;
parameter INIT_RAM_38 = 288'h0;
parameter INIT_RAM_39 = 288'h0;
parameter INIT_RAM_3A = 288'h0;
parameter INIT_RAM_3B = 288'h0;
parameter INIT_RAM_3C = 288'h0;
parameter INIT_RAM_3D = 288'h0;
parameter INIT_RAM_3E = 288'h0;
parameter INIT_RAM_3F = 288'h0;

output [17:0] DOA, DOB;
input [17:0] DIA, DIB;
input [2:0] BLKSEL;
input [13:0] ADA, ADB;
input WREA, WREB;
input CLKA, CLKB;
input CEA, CEB;
input OCEA, OCEB;
input RESETA, RESETB;

endmodule


(* blackbox *)
module rPLL (CLKOUT, CLKOUTP, CLKOUTD, CLKOUTD3, LOCK, CLKIN, CLKFB, FBDSEL, IDSEL, ODSEL, DUTYDA, PSDA, FDLY, RESET, RESET_P);
input CLKIN;
input CLKFB;
input RESET;
input RESET_P;
input [5:0] FBDSEL;
input [5:0] IDSEL;
input [5:0] ODSEL;
input [3:0] PSDA,FDLY;
input [3:0] DUTYDA;

output CLKOUT;
output LOCK;
output CLKOUTP;
output CLKOUTD;
output CLKOUTD3;

parameter FCLKIN = "100.0";         // frequency of CLKIN
parameter DYN_IDIV_SEL= "false";    // true:IDSEL, false:IDIV_SEL
parameter IDIV_SEL = 0;             // 0:1, 1:2 ... 63:64
parameter DYN_FBDIV_SEL= "false";   // true:FBDSEL, false:FBDIV_SEL
parameter FBDIV_SEL = 0;            // 0:1, 1:2 ... 63:64
parameter DYN_ODIV_SEL= "false";    // true:ODSEL, false:ODIV_SEL
parameter ODIV_SEL = 8;             // 2/4/8/16/32/48/64/80/96/112/128

parameter PSDA_SEL= "0000";
parameter DYN_DA_EN = "false";      // true:PSDA or DUTYDA or FDA, false: DA_SEL
parameter DUTYDA_SEL= "1000";

parameter CLKOUT_FT_DIR = 1'b1;     // CLKOUT fine tuning direction. 1'b1 only
parameter CLKOUTP_FT_DIR = 1'b1;    // 1'b1 only
parameter CLKOUT_DLY_STEP = 0;      // 0, 1, 2, 4
parameter CLKOUTP_DLY_STEP = 0;     // 0, 1, 2

parameter CLKFB_SEL = "internal";   // "internal", "external"
parameter CLKOUT_BYPASS = "false";  // "true", "false"
parameter CLKOUTP_BYPASS = "false"; // "true", "false"
parameter CLKOUTD_BYPASS = "false"; // "true", "false"
parameter DYN_SDIV_SEL = 2;         // 2~128, only even numbers
parameter CLKOUTD_SRC =  "CLKOUT";  // CLKOUT, CLKOUTP
parameter CLKOUTD3_SRC = "CLKOUT";  // CLKOUT, CLKOUTP
parameter DEVICE = "GW1N-1";        // "GW1N-1", "GW1N-4", "GW1N-9", "GW1NR-4", "GW1NR-9", "GW1N-4B", "GW1NR-4B", "GW1NS-2", "GW1NS-2C", "GW1NZ-1", "GW1NSR-2", "GW1NSR-2C", "GW1N-1S", "GW1NSE-2C", "GW1NRF-4B", "GW1N-9C", "GW1NR-9C", "GW1N-4C", "GW1NR-4C"

endmodule

(* blackbox *)
module PLLVR (CLKOUT, CLKOUTP, CLKOUTD, CLKOUTD3, LOCK, CLKIN, CLKFB, FBDSEL, IDSEL, ODSEL, DUTYDA, PSDA, FDLY, RESET, RESET_P, VREN);
input CLKIN;
input CLKFB;
input RESET;
input RESET_P;
input [5:0] FBDSEL;
input [5:0] IDSEL;
input [5:0] ODSEL;
input [3:0] PSDA,FDLY;
input [3:0] DUTYDA;
input VREN;

output CLKOUT;
output LOCK;
output CLKOUTP;
output CLKOUTD;
output CLKOUTD3;

parameter FCLKIN = "100.0";         // frequency of CLKIN
parameter DYN_IDIV_SEL= "false";    // true:IDSEL, false:IDIV_SEL
parameter IDIV_SEL = 0;             // 0:1, 1:2 ... 63:64
parameter DYN_FBDIV_SEL= "false";   // true:FBDSEL, false:FBDIV_SEL
parameter FBDIV_SEL = 0;            // 0:1, 1:2 ... 63:64
parameter DYN_ODIV_SEL= "false";    // true:ODSEL, false:ODIV_SEL
parameter ODIV_SEL = 8;             // 2/4/8/16/32/48/64/80/96/112/128

parameter PSDA_SEL= "0000";
parameter DYN_DA_EN = "false";      // true:PSDA or DUTYDA or FDA, false: DA_SEL
parameter DUTYDA_SEL= "1000";

parameter CLKOUT_FT_DIR = 1'b1;     // CLKOUT fine tuning direction. 1'b1 only
parameter CLKOUTP_FT_DIR = 1'b1;    // 1'b1 only
parameter CLKOUT_DLY_STEP = 0;      // 0, 1, 2, 4
parameter CLKOUTP_DLY_STEP = 0;     // 0, 1, 2

parameter CLKFB_SEL = "internal";   // "internal", "external"
parameter CLKOUT_BYPASS = "false";  // "true", "false"
parameter CLKOUTP_BYPASS = "false"; // "true", "false"
parameter CLKOUTD_BYPASS = "false"; // "true", "false"
parameter DYN_SDIV_SEL = 2;         // 2~128, only even numbers
parameter CLKOUTD_SRC =  "CLKOUT";  // CLKOUT, CLKOUTP
parameter CLKOUTD3_SRC = "CLKOUT";  // CLKOUT, CLKOUTP
parameter DEVICE = "GW1NS-4";       // "GW1NS-4", "GW1NS-4C", "GW1NSR-4", "GW1NSR-4C", "GW1NSER-4C"

endmodule

(* blackbox *)
module OSC(OSCOUT);
output OSCOUT;

parameter FREQ_DIV = 100;
parameter DEVICE = "GW1N-4";
endmodule

(* blackbox *)
module OSCZ(OSCOUT, OSCEN);
input OSCEN;

output OSCOUT;

parameter FREQ_DIV = 100;
endmodule

(* blackbox *)
module OSCF(OSCOUT, OSCOUT30M, OSCEN);
input OSCEN;

output OSCOUT;
output OSCOUT30M;

parameter FREQ_DIV = 100;
endmodule

(* blackbox *)
module OSCH(OSCOUT);
output OSCOUT;

parameter FREQ_DIV = 96;
endmodule

(* blackbox *)
module OSCW(OSCOUT);
output OSCOUT;

parameter FREQ_DIV = 80;
endmodule

(* blackbox *)
module OSCO(OSCOUT, OSCEN);
input OSCEN;

output OSCOUT;

parameter FREQ_DIV = 100;
parameter REGULATOR_EN = 1'b0;
endmodule