Add GPIO extender initial configuration that is needed to configure
some important GPIOs and ensure that the dev board is ready to work.
Add i2c_write function that make a write transfer to any slave device.
Give a new Product ID to ANGIE to make it different than the non
programmed ANGIE.
Change-Id: I0a8dacb7fe218145b7d3ed1cb75f106ed6256714
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8072
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Give ANGIE a new PID after renumeration to be able to distinguish
the two cases (programmed and not programmed)
Change-Id: I30a91d8ed2e8e261221488b98d40a027ca41da52
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7991
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
remove angie_clear_queue function from executing before the
angie_execute_queued_commands function and making it at the
end of the reset function.
Change-Id: Id8a0664fbd5b8f9730545ce0f8f272ae0b0e7e78
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7990
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We want to keep the tri-state buffers located between the FPGA
and the board, in 'Z' state until we launch an i2c connection.
We launch an i2c start condition, make the SCL
direction 'OUT' to start the i2c protocol and at the end
of the i2c connection at the stop condition, we re-make
the tri-state buffers at 'Z' state.
Change-Id: Ic597a70d0427832547f6b539864c24ce20a18c64
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7989
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Send bitstream size to firmware to initialize the GPIF count registers,
since we're going to send this size via GPIF, we need to give the exact
number of bytes to be sent, then the GPIF counter will decrement with
every clock cycle (every byte sent) until reaching zero and stops.
Change-Id: Ib4e8e0f95a6a4a95ef4888ba8a04a0ea45567f5a
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7988
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
clang build triggers an error for an uninitialized value of the
variable 'instr'.
This is a false positive, as the macro
#define MIPS32_CONFIG3_ISA_MASK (3 << MIPS32_CONFIG3_ISA_SHIFT)
guarantees the switch/case already covers all the possible values
with cases 0, 1, 2 and 3.
Silent clang by adding a useless default case to the switch.
While there, fix the indentation of the switch/case accordingly to
OpenOCD coding style.
Change-Id: I0ae316754ce7d091dd8366bf314b8e6ee780e313
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 7de4b1202d ("target/mips32: add cpu info detection")
Reviewed-on: https://review.openocd.org/c/openocd/+/8065
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Some OpenOCD command gets fragment of TCL scripts as command-line
argument, fragments that will be kept and executed later on.
E.g. the command 'configure' gets the body of an OpenOCD event:
$TARGET configure -event halted {TCL code}
These commands store the argument as a Jim_Obj and pass it to the
jimtcl interpreter when the TCL fragment has to be executed.
Using Jim_Obj as storage is relevant to let the jimtcl interpreter
to recover extra info of the TCL fragment, like the file-name and
the line-number that contain the fragment, that will be printed
out in case of run-time errors.
While converting the commands to COMMAND_HANDLER, we should avoid
storing the argument as C strings otherwise we will loose precious
info in case of run-time errors making challenging the debugging
of such TCL fragments.
Extend the struct command_invocation to contain the array that
points to the Jim_Obj of the command arguments.
This will be used while converting commands to COMMAND_HANDLER.
Change-Id: If37c5f20e9a71349f77ba1571baf1e6778e28aa5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8057
Tested-by: jenkins
The jimtcl interpreter guarantees that the Jim objects in argv[]
are not deallocated during the command execution. Thus, there is
no need to copy the string content of argv[].
Simplify exec_command() by inlining its two sub-functions and
dropping the strdup().
While there, add a LOG_ERROR() for out of memory.
Change-Id: I3e21ed7da50ca0bd072edbd49fca9740c81f95b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8055
Tested-by: jenkins
The output parameter nwords is always equal to the input parameter
argc, when the function succeeds.
Drop the parameter nwords and let the caller use directly the
value in argc.
While there, convert some 'unsigned' to 'unsigned int'.
Change-Id: Ie3d8ce1351792f3c07fe39cdcbcd180fd24dc928
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8054
Tested-by: jenkins
In both functions script_debug() and script_command_args_alloc()
the variable len is never used, and Jim_GetString() does not
mandate it.
Drop the variable and pass NULL to Jim_GetString().
Change-Id: I754b27a59c6087cde729496be42609d2a7145b0c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8053
Tested-by: jenkins
Commit e370e06b72 ("target: Deprecate 'array2mem' and
'mem2array''") has already replaced the deprecated root versions
of commands mem2array and array2mem with TCL proc's that use
'read_memory' and 'write_memory'. It has left the deprecated code
of the target's version of the commands because the effort to code
the TCL replacement was not considered valuable.
To drop the last jim_handler commands, I consider much easier and
less error-prone to code them in TCL instead of converting the
deprecated code to COMMAND_HANDLER.
Drop the code in target.c and extend the TCL proc's.
While there, add the TCL procs to _telnet_autocomplete_skip.
Change-Id: I97d2370d8af479434ddf5af68541f90913982bc0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8052
Tested-by: jenkins
When requested by the core code (handle_breakpoints = true),
arc_resume() should be able to advance over a potential breakpoint set
at the resume address instead of getting stuck in one place. This is
achieved by removing the breakpoint, executing one instruction,
resetting the breakpoint, then proceeding forward as normal.
With this patch applied, openocd is now able to resume from a
breakpoint halt when debugging ARCv2 targets via telnet.
This has previously been committed to the Zephyr project's openocd repo
(see https://github.com/zephyrproject-rtos/openocd/pull/31).
Change-Id: I17dba0dcea311d394b303c587bc2dfaa99d67859
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7817
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Presently, we rely on gdb to restore break/watchpoints upon resuming
execution in arc_resume(). To match this behavior in absence of gdb
(more specifically, when handle_breakpoints is true), this patch
explicitly re-enables all breakpoints and watchpoints in arc_resume().
This has previously been committed to the Zephyr project's openocd repo
(see https://github.com/zephyrproject-rtos/openocd/pull/31).
Change-Id: I59e9c91270ef0b5fd19cfc570663dc67a6022dbd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7816
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
For Armv8.1-M based cores, detect if the core implements the optional
M-profile vector extension (MVE), using MVFR1 register.
While at there rework armv7m->fp_feature detection based on MVFR0
and MVFR1 registers.
Change-Id: I92d5b1759aea9f7561d285f46acdec51d6efb7b4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6950
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
By queuing multiple jtag transfers the connection speed between
JTAG-Host and JTAG-Hub is improved. This is due to much less
calls to OS functions. An improvement of about x30 has been
measured with ftdi-based jtag adapters
For this to work the JTAG-Host server needs to know if flow control
is enabled on the JTAG-Hub ports. This is possible with newer
JTAG-Hub/JtagCDC. For old JTAG-Hubs the queuing is not enabled so
this change is backwards compatible.
Change-Id: I8a5108adbe2a2c1e3d3620b5c9ff77a546bfc14e
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7978
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On some systems (at least Windows/CYGWIN and macOS) libusb_dev_mem_alloc()
simply returns NULL. The helper can fall-back to malloc() to allocate
CMSIS-DAP pending command/response buffers.
Fixes: fd75e9e542 (jtag/drivers/cmsis_dap_bulk: use asynchronous libusb transfer)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I89660f6747ad9d494b8192711cbbee5764e058fa
Reviewed-on: https://review.openocd.org/c/openocd/+/8044
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
On some systems (at least Windows/CYGWIN and macOS) libusb_dev_mem_alloc()
simply returns NULL.
Use the result of the very first libusb_dev_mem_alloc() call to decide
if the underlining system supports dev mem allocation or we should
fall-back to plain heap malloc().
From the decision time on, keep using the selected type of memory allocator
and deallocator.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ia1f0965cea44b4bb6d936b02ec43f5a16a46f080
Reviewed-on: https://review.openocd.org/c/openocd/+/8059
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In loops that typically take longer time to complete, check if there is
a pending shutdown request. If so, terminate the loop.
This allows to respond to a signal requesting a shutdown during some
loops which do not return control to main OpenOCD loop.
Change-Id: Iace0b58eddde1237832d0f9333a7c7b930565674
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Based on Daniel Goehring's [1] and Peter Collingbourne's [2] work.
Probe for support of 8, 16 bit and if the large data extension is available
also probe for 64, 128 and 256 bit operations.
Probe for the ability of packing 8 and 16 bit data
(formerly probed in mem_ap_init()). The probe is integrated to
mem_ap_read/write() routines and takes place just before the first memory
access of the specific size.
Add 64, 128 and 256 bit MEM-AP read/writes.
Introduce specific error codes for unsupported transfer size
and for unsupported packing.
Change-Id: I180c4ef17d2fc3189e8e2f14bafd22d857f29608
Link: 7191: target/adiv5: add MEM-AP 64-bit access support | https://review.openocd.org/c/openocd/+/7191
Link: 7436: arm_adi_v5: Support reads wider than 32 bits | https://review.openocd.org/c/openocd/+/7436
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7576
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Prevent packed writes with Nuvoton NPCX quirks because the workaround
uses all byte lanes for one byte or halfword and thus precludes packing.
Eliminate quirk code for size 4 as it is equivalent to the common code.
Make the quirk code for sizes 2 and 1 easier readable.
Change-Id: I72324e56a49b4712bd3769e03dce01427d9fcd73
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7575
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce ti_be_lane_xor for byte lane correction
and use common code for both quirk and regular conversion.
The same lane correction takes place in both mem_ap_read/write()
- it was obfuscated in original code with different bitwise and arithmetic
operations.
Change-Id: I6a30672b908770323d30813a714e06ab8695fe26
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7574
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Update mips32 instructions, add barrier and sync related insts.
Add SYNC and barrier instruction blocks for memory access safety.
These instructions are not supported on Lexra and/or MIPSr1 CPUs,
detections were added and they will be executed conditionally.
Rework mips32_pracc_read/write_regs function.
Checkpatch-ignore: MACRO_ARG_REUSE
Change-Id: Ib14112f37ff1f060b1633df73d671a6b09bb2178
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7865
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add detection for mips cpu types by using prid.
Add cpuinfo command for inspecting more verbose info.
Add MIPS Architecture specs in openocd docs.
Change-Id: I28573b7c51783628db986bad0e226dcc399b4fa6
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7912
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested with APM32F030C8T.
Change-Id: I63cd8b66424135dae481a96ba560e6f0b1f9544e
Suggested-by: Christian U <info@cu-tec.de>
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8014
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some bitbang interfaces have no speed regulation and work as fast as
they can. Only the sequence of execuded commands is guaranteed but
not the timing. It works most of time with one exception: when the
JTAG_SLEEP command is executed, we expect that all previous commands
already finished so that the sleep interval is guaranteed.
For now there may be situations when the sleep time has passed but
previous commands are not actually executed.
This patch adds a flush command to the bitbang interface, connects it
to the existing implementation for remote_bitbang, and runs it when
the JTAG_SLEEP command is executed.
Change-Id: If40894a63d29a260a4ded134b008df6dd1e89c46
Signed-off-by: Aleksey Shargalin <myokaski@gmail.com>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/4284
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Some devices with an internal multi-tap JTAG router require a vendor
specific bypass instruction to bypass the master TAP when addressing
slave taps internal to the same device. On these devices the standard
bypass instruction bypasses the whole device.
Change-Id: I4506f0e67c9e4dfe39b7fa18c63d67900313e594
Signed-off-by: Henrik Nordström <henrik.nordstrom@addiva.se>
Reviewed-on: https://review.openocd.org/c/openocd/+/8041
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
swd_connect_multidrop() sent DORMANT_TO_SWD and called
swd_multidrop_select_inner(). DORMANT_TO_SWD sequence ends
with a LINE_RESET sequence.
swd_multidrop_select_inner() sent LINE_RESET sequence again.
It was useless in this case.
swd_connect_multidrop() emited JTAG_TO_DORMANT and DORMANT_TO_SWD
sequences before connecting each DAP in SWD multidrop bus.
It is sufficient to emit JTAG_TO_DORMANT and DORMANT_TO_SWD
just once and emit the shorter LINE_RESET instead for subsequent DAPs.
Introduce a global variable swd_multidrop_in_swd_state
and use it to control what sequence is emitted.
In case of reconnect after an error, always use the full switch
JTAG_TO_DORMANT and DORMANT_TO_SWD.
Change-Id: Iba21620f6a9680793208bf398960ed0eb59df3b1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7218
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
SWD multidrop requires some initialization once before connecting
all daps. Provide an optional pre-connect dap operation.
Change-Id: I778215c512c56423a425dda80ab19a739f22f285
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7542
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The original code supported ADIv5 only, just one SELECT register
with some reserved bits - the pseudo value DP_SELECT_INVALID was
just fine to indicate the DP SELECT register is in an unknown state.
Added ADIv6 support required DP SELECT and SELECT1 registers
without reserved bits. Therefore DP_SELECT_INVALID value became
reachable as a (fortunately not really used) ADIv6 AP ADDR.
JTAG DPBANKSEL setting support introduced with ADIv6 does not
honor DP_SELECT_INVALID correctly: required select value
gets compared to DP_SELECT_INVALID value and the most common zero
bank does not trigger DP SELECT write.
DP banked registers need just to set DP SELECT. ADIv6 AP register
addressing scheme may use both DP SELECT and SELECT1. This further
complicates using a single invalid value.
Moreover the difference how the SWD line reset influences
DPBANKSEL field between ADIv5 and ADIv6 deserves better handling
than setting select cache to zero and then to DP_SELECT_INVALID
in a very specific code positions.
Introduce bool flags indicating the validity of each SELECT
register and one SWD specific for DPBANKSEL field.
Use the latter to prevent selecting DP BANK before taking
the connection out of reset by reading DPIDR.
Treat DP SELECT and SELECT1 individually in ADIv6 64-bit mode.
Update comments to reflect the difference between ADIv5 and ADIv6
in SWD line reset.
Change-Id: Ibbb0b06cb592be072571218b666566a13d8dff0e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7541
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For unknown reasons, the coreutils tool 'od' on MacOS outputs an
extra empty line, which appears in the new auto-generated files.
Modify the script bin2char.sh to drop every empty line.
Change-Id: Id835fecadb58ad4ddfc11ef9f9a2e8d75c5dffe9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8051
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
Reviewed-by: Henrik Nordström <henrik.nordstrom@addiva.se>
In loops that typically take longer time to complete, check if there is
a pending shutdown request. If so, terminate the loop.
This allows to respond to a signal requesting a shutdown during some
loops which do not return control to main OpenOCD loop.
Change-Id: Iace0b58eddde1237832d0f9333a7c7b930565674
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8032
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If the remote_bitbang host does not execute requests immediately,
delays performed inside OpenOCD can be lost. This option allows
the delays to be sent to the remote host so that they can be
queued and executed in order.
Signed-off-by: Jeremy Herbert <jeremy.006@gmail.com>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Change-Id: Ie1b09e09ea132dd528139618e4305154819cbc9e
Reviewed-on: https://review.openocd.org/c/openocd/+/7472
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix some coding style issues.
Change-Id: I8196045f46ce043ed0d28cb95470132b3a7de1bb
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The field backup_working_area is always used as a boolean value.
Use bool type for backup_working_area.
Change-Id: I55c68d717dbbe9e5caf60fd1db368527c6d1b995
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8036
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
I don't think there are any real bugs here, but at least this gives us a
clean slate moving forward.
Change-Id: I29c6c398c28dfe580f9a2deb3bdbcfc491a2ceb6
Signed-off-by: Tim Newsome <tim@sifive.com>
Currently all Atmel CMSIS-DAP interfaces are assumed to have 512 byte
reports except for the mEDBG (found on Xplained Mini boards) and the nEDBG
(found on Curiosity Nano boards). This check is far from exaustive and it
results in some Microchip programmers (like the MPLAB Snap and PICkit 4)
not working correctly with OpenOCD.
Instead of assuming that Atmel programmers have 512 byte reports unless we
know otherwise, this commit flips the logic around. Only the older "third
generation" EDBG based programmers have 512 byte report sizes, and that 64
bytes will be more common in Microchip tools going forward.
The list of PIDs for 3rd generation Microchip programmers comes from
toolinfo.py from Microchip's pyedbglib.
This commit adds a more generic "quirks" list that will allow programmers
with unusual report sizes to be added easily in the future.
Change-Id: Ic39a4bdcd67c4c93d5707657c6ee5d216bc4437a
Signed-off-by: Samuel Dewan <samdewan@me.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8033
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
These messages helps to clarify current status of examination process
Change-Id: I5d93903c4680deed2c1bf707d8f7ef0b48ffdc9a
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8013
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This functionality can be useful for;
1-ESP flashing code to load flasher stub on target and
write/read/erase flash.
2-ESP GCOV command uses some of these functions to run
onboard routines to dump coverage info.
This is high level api for the Espressif xtensa and riscv targets
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I5e618b960bb6566ee618d4ba261f51af97a7cb0e
Reviewed-on: https://review.openocd.org/c/openocd/+/7759
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The goal of this commit is to provide more robust error handling in
`write_memory_progbuf()`. This is achieved by rewriting it in a fashion
similar to `read_memory_progbuf()`.
The motivation is: some instability in `load_image` was encountered. No
stable reproduction could be obtained, so the root cause was not
determined. Therefore, it was decided to clean-up the code, that may be
implicated in such failures.
Examples of unhanded errors in the code prior to this commit:
* Most of `dmi_write()` return values are discarded.
* If `dm_read()` on `abstractcs` failed (line 4546), `abstractauto` was
not cleared.
Furthermore, the structure of the code was quite complicated, which made
it hard to analyze and reason whether or not all possible failures are
handled properly.
Change-Id: I8a100b686e594855fbf34acf5ccf0e1550f18869
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Introduce 'cmsis-dap quirk' command to enable and
disable quirk mode.
If enabled, disconnect and connect before a switch
sequence and do not use multiple packets pipelining.
Change-Id: I6576f7de9f6c98a25c3cf9eec9a456a23610d00d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7966
Tested-by: jenkins
Use it whenever an out-of-sync response is detected to clean
USB bulk transfer state.
USB hidapi does not offer any means to cancel a pending request,
therefore cmsis_dap_hid_cancel_all() does nothing.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ie36fa760c1643ae10be0e87fc633068965a72242
Reviewed-on: https://review.openocd.org/c/openocd/+/7366
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
The synchronous libusb_bulk_transfer() always waits
for the transfer to complete. Therefore it does not allow issuing
multiple USB requests as used on HID backend.
Switch to asynchrounous libusb_submit_transfer().
With this patch a good USB FS based CMSIS-DAPv2 adapter
almost doubles the throughput:
adapter speed: 20000 kHz
poll off
> load_image /run/user/1000/ram256k.bin 0x20000000
262144 bytes written at address 0x20000000
downloaded 262144 bytes in 0.428576s (597.327 KiB/s)
> dump_image /dev/null 0x20000000 0x40000
dumped 262144 bytes in 0.572875s (446.869 KiB/s)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ic6168ea4eca4f6bd1d8ad541a07a8d70427cc509
Reviewed-on: https://review.openocd.org/c/openocd/+/7365
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix the 'wp' command documentation.
Change-Id: I70f3110e8ce286051f8f810260f1857b2285e634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8022
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
By definition in `target/target.h`, `coreid` is not a unique identifier
of a target -- it can be the same for targets on different TAPs.
Change-Id: Ifce78da55fffe28dd8b6b06ecae7d8c4e305c0a2
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7997
Tested-by: jenkins
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When user requested a change on cp0 status register,
it may contain changes on EXL/ERL bits, and changes on
these bits could lead to differnt behaviours on writing
to other cp0 registers.
Change-Id: Ic83039988c29c06ee134226b52de943c46d19da2
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7914
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD style guide(`doc/manual/style.txt`) prohibits use of VLA:
> - use malloc() to create dynamic arrays. Do @b not use @c alloca
> or variable length arrays on the stack. non-MMU hosts(uClinux) and
> pthreads require modest and predictable stack usage.
Change-Id: I12e4a5087fd056d69866137237af6deca27f5d33
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
`LOG_TARGET_DEBUG()` reports file, line and function name at the call
site. This information is not helpfull if it always points to the same
location inside `log_debug_reg()`.
Change-Id: Ib73be0344fb5c80c9ac8e5fdee1084d405522eb7
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
If we can't remove bp/wp, we will stuck in endless loop
Change-Id: I44c0a164db1d15c0a0637d33c75087a49cf5c0f4
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7940
Tested-by: jenkins
Reviewed-by: Anatoly P <kupokupokupopo@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There was a big conflict with this one incoming change. This version of
the code passes all the tests (which don't test for the changed behavior
at all AFAIK), and at least passes errors back everywhere.
Conflicts:
src/target/breakpoints.c
Change-Id: I72f75a3e08deda7e624e8bb82e1a9ea07a7a9276
Instead of returning an 'error string', throw an error. This makes it
much easier to handle errors in Tcl scripts or in tools that use Tcl RPC.
Change-Id: I75c48750cfad7430fa5e6bc88fe04ebd59d34cea
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8006
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is useful when using the SEGGER RTT tooling, as the SEGGER RTT
tool J-Link RTT Viewer version 7.84f requires that it receives a
messages immediately after connecting. Otherwise it will give a timeout
and it will not connect.
Change-Id: I9240a1b6a93cd5c0fbd18292afb33b89013d78bf
Signed-off-by: Thiemo van Engelen <tvanengelen@victronenergy.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7752
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: I990c0f7a0871f4b1a0fcdd13afc190149302443c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8003
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: Id32440cdd531077008abd679add32246c4249eb2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8001
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: Idf3d7a46ddecd70823e06bc3997f41fcdb8e501f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8000
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The correct syntax is already suggested due to the return
value used.
While at it, apply some minor code improvements.
Change-Id: I676e2ebf5714c850a436854a32c2e9d2f181d537
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7999
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The correct syntax is already suggested due to the return
value used.
Change-Id: I0f4a7f93fdf056e7517c754d6d4ecd7928f1d226
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7992
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The correct syntax is already suggested due to the return
value used.
Change-Id: I971a579014c1eaf13b1932f7fa87c020a8eba69c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7971
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While at it, remove the syntax error messages as the correct
syntax is already suggested due to the return value used.
Change-Id: I9310ba96ed3f8a85c37cee9193e481ad3df02e77
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7969
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The mips opcode macro for the SRL opcode was using the wrong constant
value:
SRA -- Shift right arithmetic
Encoding: 0000 00-- ---t tttt dddd dhhh hh00 0011
SRL -- Shift right logical
Encoding: 0000 00-- ---t tttt dddd dhhh hh00 0010
This corrects the opcode constant for SRL and adds the SRA opcode for
completeness.
There is only one user of MIPS32_OP_SRL in src/flash/nor/cfi.c:
Since the mask constant (0x00000080 for the DQ7 mask) shifted in this
case would never have the sign bit set, it worked fine even though it
was accidentally using the SRA opcode instead of SRL.
Change-Id: I0a80746e2075c7df1ce35b9db00d9d0b997a3feb
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/3613
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The variable 'mode' was introduced in
commit 4dc8cd201c ("cmsis-dap: add initial cmsis-dap support")
but never has been used (just cleared)
Change-Id: Ia741d181ee8006bd0d872f3358a57e045235741a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7965
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We were previously inadvertently clearing the top 32 bits of SCTLR_EL1
during read_memory/write_memory as a result of using 32-bit operations
to access the register and because the fields used to temporarily
store the register were 32-bit. Fix it.
Change-Id: I657d7f949e1f7ab6bf90609e3f91cae09cade31a
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7939
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Associativity=0 means that only one CMO is needed for all ways.
It could also mean that the cache is 1-way, but this is less likely.
Currently Associativity=0 causes us to hang in the while loop in
decode_cache_reg. Fix it by skipping the loop in this case. We can let
way_shift be set to the arbitrary value of 0 because in the case where
Associativity=0 we only ever shift 0 by it before ORing it into the
CMO operand.
Change-Id: I7c1de68d33f6b3ed627cbb1e2401d43185e4c1e3
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7916
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds target logging to breakpoint
handling code. This makes it easier to
debug multicore/multithread systems.
Change-Id: I6bea8079a457070a8f63d0ce381a4ece6f5a190a
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7922
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If we can't remove bp/wp, we will stuck in endless loop
Change-Id: I44c0a164db1d15c0a0637d33c75087a49cf5c0f4
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7940
Tested-by: jenkins
Reviewed-by: Anatoly P <kupokupokupopo@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Break- and watchpoints are not removed when a target is destroyed
which introduces a memory leak.
Change-Id: I6143d48f7efd765b7752a12fdc337da3496d896f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7956
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In the unusual (and even incorrect) case of running the command
target create ...
before defining an adapter and the associated transport, the
command causes a segmentation fault. E.g.:
openocd -c 'target create cpu cortex-m -endian little'
Check that get_current_transport() returns a valid pointer before
referencing it.
Change-Id: I9796a7e92196ef3df5c7152b27c34102045dc9e7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7962
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
I use a script to compare the commands in the code with the ones
in the documentation.
Fix the style of the data to simplify the parsing.
Change-Id: I0f1d7e9ff5e2928312ca1a2f3424f82d2910580a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7960
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Now it returns `resource not available`
Change-Id: Ifbbd468bdf62023850690eb96fe8a16f4114e915
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
The existing code didn't seem to work right at all. I have spike
modifications that exercise these new cases. I'll merge those once this
has merged.
Change-Id: I89bd336f34f1b208a76f25b6b41fe3877800765b
Signed-off-by: Tim Newsome <tim@sifive.com>
Compilers are good at optimizing, and with functions it's abundantly
clear what all the types involved are. This change means we don't have
to be super careful about the type of values because of what the macro
might do to them that might cause overflow.
The only place where the return type matters is in printf-style
functions, and I made get_value32() for those cases where a change was
needed.
This should set the stage for simply copying the latest debug_defines.h
from the debug spec build again.
Change-Id: I5fb19d0cfc1e20137832a7b344b05db215ce00e1
Signed-off-by: Tim Newsome <tim@sifive.com>
The reasoning for the change:
* `__func__` is part of C99, `__PRETTY_FUNCTION__` is GNU extension.
* `__PRETTY_FUNCTION__` is defined to be the same as `__func__` for C
sources by GCC documentation but differ for C++ sources (full
signature instead of just a name).
* Currently Clang does support `__PRETTY_FUNCTION__`, though it uses
GCC's C++ variant across C and C++.
Therefore using `__PRETTY_FUNCTION__` creates confusion and does not
provide any valueble information in the logs.
Change-Id: Ie0db6d73f602784b6752a30911dcef3dd7ee4594
Sometimes, the value from of some DMI scans has no meaning (e.g. when
`op` is read). Such values should not be decoded. To make the dumps more
consistent, `<no decoding available>` is printed when there is no
decoding for a register.
Change-Id: I415f06a5a80f2fc8fb8ab3f79132bdf0602c8ad6
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Loading a bitstream to cetrus device crashed due to
missing initialization.
Change-Id: Ibd9a04b84e514f9635af01a2b73bae478e534eb7
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7908
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This allows programmatically determining the debug reason.
Change-Id: I0c3e85cebb6dc28fc0fc212beca84a484ac654a5
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7952
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Fixes below Sparse tool warning.
warning: symbol 'breakpoint_watchpoint_remove_all' was not declared.
Should it be static?
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I4af1d5aa54abcb45f746b877513ba0b5fccbeb47
Reviewed-on: https://review.openocd.org/c/openocd/+/7955
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Marek Vrbka <marek.vrbka@codasip.com>
Enhance `mips32_read_config_regs` to better detect MIPS32 ISA,
DSP, and FPU features, allowing user to get more detailed
target information.
Most of these information will be used in MIPS m/iAptiv support.
Change-Id: I23571a626ec64fa019acac91bdbfcb434373bfc1
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7911
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This patch forces a read of register from the target
in the get_reg command in case the register cache
does not hold a valid value at that moment.
Note that the command "reg" already handles it
correctly, no fix is needed there.
Change-Id: I75fad25188e94ee4e06162ab6d600ea24dbf590a
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7958
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The original documents from Jedec since JEP106BG, do not report
the entry for "21 NXP (Philips)", replaced by "c".
It's clearly a typo.
Keep the line from JEP106BF.01 for "NXP (Philips)".
Change-Id: I273c8c5ecf48336ce5189b484a7236273ba90184
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7954
Tested-by: jenkins
By definition in `target/target.h`, `coreid` is not a unique identifier
of a target -- it can be the same for targets on different TAPs.
Change-Id: Ifce78da55fffe28dd8b6b06ecae7d8c4e305c0a2
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
This patch replaces ~(typeof(watchpoint->mask))0 with
WATCHPOINT_IGNORE_DATA_VALUE_MASK. This improves
readability and moves the RISCV target in line with
other targets.
Change-Id: I15ac4d4ee76098b304d9b22f720911ba4329c190
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Depending on configuration, the existing implementation of watchpoints is
rather inefficient for certain scenarios. Consider HW that:
1. triggers 0-3 can be used as instruction breakpoints
2. triggers 4-7 can be used as data breakpoints (watchpoints)
3. NAPOT triggers are not supported.
Now, consider that we have a pending watchpoint. And we perform a "step"
operation. According to the current implementation:
* OpenOCD will disable watchpoints
* Perform a single-step
* Will try to restore the original watchpoints. It will need 12 attempts
to find a suitable trigger: (8 attempts to try NAPOT, and another 4 to try
GE+LE).
This patch introduces a dedicated cache for requests to triggers. It
significantly speeds things up, since we cache failed attempts and no
additional interactions with HW is necessary.
Change-Id: Ic272895eaa763a7ae84d14f7633790afd015ca9d
Signed-off-by: Anastasiya Chernikova <anastasiya.chernikova@syntacore.com>
Otherwise it won't compile for me. Not sure why that doesn't affect the
automated builds.
Change-Id: Ic66c743e1698c4c0772e5601723cb5c711b4fa5c
Signed-off-by: Tim Newsome <tim@sifive.com>
Since DPC is WARL (same rules as MEPC according to
the specification), it is possible that
writes to it won't result in the exact value present.
Therefore, writes to it shouldn't be cached, same as
with other WARL registers.
Change-Id: I818c0cef9727b999b7d84b19f9f42cd706c99d69
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Added the ability to enter dimensionless registers
Change-Id: I1b781959ce4690ec65304142bd9a7c6f540b3e86
Signed-off-by: Anastasiya Chernikova <anastasiya.chernikova@syntacore.com>
Now:
1) If mmu is disabled, virt2phys succeeded and returns physical address
2) If mmu is enbaled, but translation fails, read/write_memory fails
Change-Id: I312309c660239014b3278cb77cadc5618de8e4de
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Removing flash driver "gd32vf103_flash".
This driver has been deprecated since June-1-2022, and was scheduled
for removal in June 2023.
Change-Id: Ib6f4dcba11e91a095b3a20eedd864589084b7fa9
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
This incorrect extra call has been removed in upstream code already
in March 2022, see https://review.openocd.org/c/openocd/+/6836 .
Remove it from riscv-openocd as well.
Change-Id: Ie341f5578c8bfdc518adf1e4bc134919ab76f803
Signed-off-by: Jan Matyas <jan.matyas@codasip.com>
In jtag_libusb_open I've added a parameter for delivering the device
description for which this function should search and adjusted all
callers of this function. A new driver for WCH CH347 JTAG chips
will use this new parameter.
See also: https://review.openocd.org/c/openocd/+/7937
Change-Id: I85e1d7b1f7912ba5e223f0f26323ff3b7600e17d
Signed-off-by: EasyDevKits <info@easydevkits.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add result check for mips32_pracc_read_regs in mips32_save_context.
Change-Id: Ie796d2b05a9feb11e246c2d0771b52cad4fb70db
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7932
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reintroduce checkpatch problem, because now we can handle them better.
Change-Id: Ib81b9910433ae1a240630b898edb19da8d2d5d83
Signed-off-by: Tim Newsome <tim@sifive.com>
This makes it easier to look at log files where multiple gdb instances
are connected.
Change-Id: Ic5aca52b32ee03ac35ffbed9a2fc552abb0a1cba
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7895
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Previously, when listing the watchpoints, OpenOCD printed
numbers 0, 1 and 2 representing READ, WRITE and ACCESS type
watchpoints.
This patch changes it to 'r', 'w' and 'a'. This increases the
clarity as what type the watchpoint actually is.
Change-Id: I9eac72dfd0bb2a9596a5b0c080a3f584556ed599
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7909
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
This patch adds the "all" option to the rwp command.
It removes all watchpoints, much like rbp all removes
all breakpoints.
Change-Id: Id58dd103085e558f17afa4a287888cf085566ca9
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7907
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously, if you ran a tcl command in capture like so:
"capture { reg 0x1000 hw }"
Such command did overwrite the tcl result if LOG_LVL_INFO or
lower was logged during it.
This patch changes it by prepending the log to the tcl result instead.
As the tcl results should not be lost during capture.
Change-Id: I37381b45e15c931ba2844d65c9d38f6ed2f6e4fd
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7902
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
If wp/bp is missing at address rwp/rbp won't return zero code (on smp).
Now it fixed.
Fixes: 022e438292 ("target: Change policy of removing watchpoints/breakpoints.")
Change-Id: I3a3c245f7088fc23227b286d2191fc7f3edba702
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7910
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the ARM MCRR/MRRC instructions which require the use of
two registers to transfer a 64-bit co-processor registers. We are going
to use this in a subsequent patch in order to properly dump 64-bit page
table descriptors that exist on ARMv7A with VMSA extensions.
We make use of r0 and r1 to transfer 64-bit quantities to/from DCC.
Change-Id: Ic4975026c1ae4f2853795575ac7701d541248736
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Chalfant <michael.chalfant@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
When asked to resume an unavailable target, resume any available targets
and report success.
Change-Id: Ieafc63794c1a6eba8948c0f9ce84fa74f9765041
Signed-off-by: Tim Newsome <tim@sifive.com>
When a target in an SMP group is unavailable, the gdb layer might get an
event for a different target in that SMP group, but not one that is the
primary target for that gdb connection. So propagate events if they're
for any of the targets in the SMP group, not just if it's for the first
one in that group.
Change-Id: I8d6738762acc7c0aef96f56ce2cb7f2eeb233b33
Signed-off-by: Tim Newsome <tim@sifive.com>
Exit early if conditions aren't satisfied, instead of putting the core
code inside an if().
Also return ERROR_FAIL if conditions are satisfied but no matching
registers were found.
Change-Id: I77aa63d9f707bc38d1a71899275ba603914b52c9
Signed-off-by: Tim Newsome <tim@sifive.com>
Currently, instruction cache is being invalidated in
arc_{un,}set_breakpoint() regardless of whether the breakpoint's type is
HW or SW. For SW breakpoints, this has no net effect as the caches are
flushed as a by-product of overwriting instructions in main memory and
is thus merely unnecessary; but for HW breakpoints this invalidation is
not preceded by a flush and might lead to loss of data. This patch
removes the invalidate() call altogether to correct this undesired
behavior for HW breakpoints.
With this patch applied, all supported HW breakpoint tests from the gdb
testsuite are now passing with the arc-openocd backend.
Change-Id: I3d252b97f01f1a1e2bf0eb8fb257bdab0c544bc2
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7767
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The comment above armv8_dpm_read_current_registers() doesn't match
the implementation, as the function reads all the registers from
ARMV8_PC and above.
The registers currently read are not relevant to answer to the
usual GDB initial request through the 'g' packet. Plus the lack of
differentiation per core state (AArch32 vs AArch64) causes the
read of not existing registers in AArch32 triggering errors, as
tentatively fixed by https://review.openocd.org/5517/
Fix the code to read the registers initially required by GDB.
Modify the comment to report the register list in AArch32 and in
AArch64.
Keep the extra checks inside the read loop, even if they are
mostly irrelevant; this could prevent errors if someone needs to
extend the number of registers to read.
The current implementation of the register's description in
OpenOCD does not allow to discriminate among AArch32 and AArch64
registers. Add a TODO comment to highlight it.
Change-Id: Icd47d93c19a9e1694a7b51bbc5ca7e21a578df41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7887
Tested-by: jenkins
Move `examine_attempted` flag to target struct to make it target specific.
`Info` messages for retry and `Error` messages for failure added.
Change-Id: Id2fbe7dc68d746c936c8412289d0d149fbd80d71
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
The secure microcontroller Infineon SLx2 uses a custom Cortex-M33.
The register CPUID reports value 0x490FDB00.
Reference link to the product:
Link: https://www.infineon.com/cms/en/about-infineon/press/market-news/2022/INFCSS202211-034.html
Change-Id: I8911712c55bd50e24ed53cf49958352f470027a5
Signed-off-by: Ahmed Boughanmi <boughanmi.external@infineon.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7879
Reviewed-by: Karl Palsson <karlp@tweak.au>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds error reporting when unknown image type is specified.
Previously, OpenOCD replied with an empty string.
Change-Id: I16220b1f5deb3b966a21731f0adf7911a78e8959
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7883
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add a new riscv specific commands to disable triggers
Change-Id: Ic1842085aa66851c740e0abcbfbe0adbe930920e
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
If it fails, then pass that failure on. If it's simply not implemented,
then we can fall through and try target_get_gdb_reg_list_noread().
This difference matters when the target representing the current
hwthread is unavailable, but the target that is linked to the gdb
connection is available. In that case we want the operation to return an
error to gdb, instead of reading the register from the target that is
available.
Change-Id: I9c84ca556f818c5580e25ab349a34a226fcf0f43
Signed-off-by: Tim Newsome <tim@sifive.com>
When gdb requests to step an unavailable target, report success. When
the target becomes available, the step can complete.
Change-Id: I969ab56139f72a757552928d59edf6eabd598fa4
Signed-off-by: Tim Newsome <tim@sifive.com>
Extend riscv set_ebreak* commands.
Now it can be called without args to print current value.
riscv_ebreak* flags are moved to riscv_info struct.
Change-Id: Ib46e6b6dfc0117599c7f6715c7aaf113e63bd7dc
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Previously, the bcm2835_peri_base value would be printed as a decimal
value despite having a "0x" prefix, implying it should be a hex value.
BCM2835 GPIO: peripheral_base = 0x1056964608
Now, the value is correctly converted to hexidecimal.
BCM2835 GPIO: peripheral_base = 0x3F000000
Change-Id: Id59185423917e6350f99ef68320e2102a3192291
Fixes: b41b368255 ("jtag/drivers/bcm2835gpio: extend peripheral_base to off_t")
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
and DP_SELECT_DPBANK.
Use the defined symbols instead of magic numbers.
Change-Id: I19c86b183e57e42b96f76eed180c0492cd67bee1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7539
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Ahmed BOUDJELIDA
Antonio Borneo
ianst
Evgeniy Didin
Tarek BOCHKATI
Daniel Anselmi
Tomas Vanek
Evgeniy Naydanov
David Vidrie Leon
Walter Ji
Jan Matyas
Marc Schink
Aleksey Shargalin
Henrik Nordström
Peter Collingbourne
Tim Newsome
Parshintsev Anatoly
Jeremy Herbert
Samuel Dewan
Karl Palsson
Kirill Radkin
Erhan Kurubas
Manuel Wick
Thiemo van Engelen
Tobias Diedrich
Marek Vrbka
Anastasiya Chernikova
Jan Matyas
EasyDevKits
Florian Fainelli
Artemiy Volkov
liangzhen
Ahmed Boughanmi
Vincent Fazio