failure to write to memory was not propagated.
This is an interesting case of broken error handling:
with exceptions we wouldn't have had this at all,
and I also wonder if there is a GCC option to warn
about these kinds of potential bugs.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Parameter "type" of function armv4_5_mmu_translate_va()
is now not used.
Remove the parameter and the "enum" listing its values.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function armv4_5_mmu_translate_va() now properly signals
errors in the return value.
Remove former error handling by setting variable "type" to
value "-1".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function arm920t_write_memory() default return value
should be ERROR_OK.
All cases of local errors are handled immediately and
not further propagated.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 0538081246
introduces a compile time warning:
arm920t.c: In function ‘arm920t_write_memory’:
arm920t.c:567: warning: ‘retval’ may be used uninitialized in this function
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
any read/write operation to memory can fail.
block write algorithm error propagation was broken
in that it would continue after an error was reported
writing data to ram or the algorithm failing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
JTAG_MOVESTATE is misleading, this cmd is only used
for reset.
JTAG_PATHMOVE should be used otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hello,
"stm32x mass_erase" return ERROR_OK even if something goes wrong.
Here is a summary of changes :
* in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error
detected in FLASH_SR register;
* in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the
returned value of stm32x_mass_erase().
I don't know if there is reason to always return ERROR_OK ?
Gaëtan
ETM analyze produced no output when the trace buffer was empty.
This patch provides users with a clue.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Every time command "flash probe #" is executed, memory
structures are re-allocated without preventive free()
of former areas, causing memory leak.
Also, memory allocation does not check return value,
determining segmentation fault in case of out of memory.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
We request a id register read at the end of ahbap_debugport_init
but we never actually run the queue. In some cases this causes a
segfault.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
This second half of the patch is proposed to clean up some GDB keep alive
issues on arm7_9 targets that start up with very slow clocks. If an attempt
is made to write to key registers on the processor with a slow jtag speed,
GDB timeout warnings appear on the console (at least mine) when "reset halt"
or "reset init" commands are issued from the gdb client:
*** BEFORE PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1026). Workaround: increase "set remotetimeout" in GDB
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1027). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1004). Workaround: increase "set remotetimeout" in GDB
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
I added additional keep alive steps in areas that troubleshooting revealed
were causing problems. I only did this however for non-fast write memory
accesses. I don't think most people would be using fast memory accesses to
write to memory when the jtag and system clocks are slow anyway.
If you disagree with my feeling, think there is a more elegant way to handle
the problem, or think the patch will cause other unforeseen problems with
other targets, let me know. As you can see below, the patch does eliminate
the problem on my development station and I suspect that it will benefit
others.
*** AFTER PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
Gary Carlson
Gary Carlson, MSEE
Principal Engineer
Carlson-Minot Inc.
tcl "puts" didn't work because the logging code sensored strings
that did not include a '\n'. The correct thing is to sensor
empty strings, which are used to keep gdb connection alive.
The tcl "puts" code broke apart strings which do contain '\n' in
order to implement the -nonewline argument, which is how it
got hurt by the bug in log.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Page reads using hwecc4_infix layout segfaulted for check_bad_blocks because
the read assumed a valid data buffer, which check_bad_blocks does not use
(it only passes a 6 byte buffer for the start of OOB).
This version copes with undersized or missing data or oob buffers and uses
random read commands within the page to skip unwanted areas of data/OOB for
speed.
NOTE: Running check_bad_blocks with this layout will be reading infix
OOB locations, not manufacturer bad block markers. This means that if you
check blocks written in infix layout they will appear good, but manufacturer-
marked bad blocks may also appear good.
If you want to scan for manufactuer-marked bad blocks, you need to enable
raw_access before running check_bad_blocks, or use the non-infix layout.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
CC: David Brownell <dbrownell@users.sourceforge.net>
nand_build_bbt() was ignoring the return value from nand_read_page() and
blindly continuing.
It now passes the return value up to the caller if the read fails.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Change download rate messages about kibibytes from "kb/s" to "KiB/s" units.
See: http://en.wikipedia.org/wiki/Data_rate_units
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Remove few LOG_DEBUG() messages, together with code and
variables required to build such messages.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final step to force bus_width size during CFI flash
read.
Added CFI specific implementation cfi_read() that uses
only accesses at bus_width size.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
During cfi_write(), head and tail of destination area
could be not aligned to bus_width.
Since write operation must be at bus_width size, source
buffer size is extended and buffer padded with current
values read from flash.
Force using bus_width to read current value from flash.
Do not use cfi_add_byte() anymore, to allow removing this
function later on.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
NOR flash structure requires each access to be bus_width wide.
Fix read of flash ID accordingly to rule above.
Add case (chip_width == 4), allowed by CFI spec and coherent
with current value of CFI_MAX_CHIP_WIDTH but currently not
used by any target.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Since NOR flash devices does not handle "byte enable lanes",
each read/write access involves the whole "chip_width".
When multiple devices are in parallel, usually all chips are
enabled during each access.
All such cases are compatible with flash accesses at
"bus_width" size.
Access at "bus_width" size is mandatory for write access to
avoid transferring of garbage values to flash.
During read access the flash controller should take care,
and discard unneeded bytes. Anyway, it is good practice to
use "bus_width" size also for read.
Every memory access that does not respect "bus_width" size
is marked with a "FIXME" comment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Review and simplify computation of bufferwsize.
Add comments about variables' meaning.
The same code is present 3 times in the file.
Current patch updates all the 3 instances.
Step 1)
Replace "switch(bank->chip_width) {...}".
Illegal values of bank->chip_width are already dropped.
For legal values, the code is equivalent to:
bufferwsize = buffersize / bank->chip_width;
Step 2)
The above code replacement plus the following line:
bufferwsize /= (bank->bus_width / bank->chip_width);
is merged in a single formula:
bufferwsize = (buffersize / bank->chip_width) /
(bank->bus_width / bank->chip_width);
and simplified as:
bufferwsize = buffersize / bank->bus_width;
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Arguments chip_width and bus_width of command "flash bank" are
not fully checked.
While bus_width is later on redundantly checked in several other
parts (e.g. in cfi_command_val()) and generates run-time error,
chip_width is never checked, nor related to actual bus_width
value.
Added check to avoid:
- (chip_width == 0), that would mean no memory chip at all,
avoiding also division by zero e.g. in cfi_get_u8();
- (bus_width == 0), that would mean no bus at all;
- unsupported cases of chip_width or bus_width value not power
of 2;
- unsupported case of chip width wider than bus.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Last block was being skipped, fix by changing the loop test from "<" to "<="
First block argument was ignored, always started from block 0 (and counted
the wrong blocks as bad if first was nonzero). Now we use it.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The last_block argument to nand_erase() is checked against nand->num_blocks,
but the highest valid block number is (total - 1), the test for invalid should
be ">=" rather than ">".
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
flash cmds can now be passed either the bank name or the bank number.
For example.
flash info stm32.flash
flash info 0
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Hi,
This is my first post to the list. First, I would like to thank
everyone for their work on OpenOCD, it is a great tool to work with. I
have been using it to debug code on hardware for the Rockbox project
(www.rockbox.org).
The target that I primarily work with has a Spansion/Fujitsu NOR flash
(MBM29SL800TE). I attached a patch that adds support for this flash. I
hope it can be included in the main repository. If there is something
that needs to be changed with the patch before inclusion please let me
know.
-Karl Kurbjun
The ST/Numonix M29W128G has an issue when a 0xff cmd is sent,
it cause an internal undefined state. The workaround according
to the Numonyx is to send another 0xf0 reset cmd
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
c->sin.sin_port does not contain a valid port number so just use
service->port as this is always correct.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
There are a million reasons why cached protection state might
be stale: power cycling of target, reset, code executing on
the target, etc.
The "flash protect_check" command is now gone. This is *always*
executed when running a "flash info".
As a bonus for more a more robust approach, lots of code could
be deleted.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
No segmentationfault when sending commands to tcl-server.
modified: src/server/server.c
modified: src/server/tcl_server.c
modified: src/server/tcl_server.h
Various commands, e.g. "arm mcr xxxx" would fail if invoked upon startup
since it there was no command context defined for the jim interpreter
in that case.
A Jim interpreter is now associated with a command context(telnet,
gdb server's) or the default global command context.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove/fix lots of bugs in handling of non-contigious sections
and out of order sections.
Fix a gaffe introduced in previous commit to src/flash/nor/core.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Remove bogus error messages when trying to allocate a
large chunk of target memory and then falling back to
a smaller one.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
target memory allocation can be implemented not to show
bogus error messages.
E.g. when trying a big allocation first and then a
smaller one if that fails.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
make wait for srst deassert more long latency friendly
(JTAG over TCP/IP), print actual time if it was more than
1ms.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The current timeout for STM32 flash block erase and flash mass erase is
10 (ms), which is too tight, and fails around 50% of the time for me.
The data sheet for STM32F107VC specifies a maximum erase time of 40 ms
(for both operations).
I'd also consider it a bug that the code does not detect a timeout, but
just assumes that the operation has completed. The attached patch does
not address this bug.
The attached patch increases the timeouts from 10 to 100 ms. Please apply.
/Tobias
Fix a bug where write_image would fail if the sections
in the image were not in ascending order. This has previously
been fixed in gdb load.
Solved by sorting the image sections before running flash
write_image erase unlock foo.elf.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this is done for unlocking and it is a simple omission that
it wasn't done for sectors.
The unnerving thing is that nobody has complained about this
until now....
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This patch adds support for the length argument to the xscale implementation of
the wp command. Per discussion with David, the length argument specifies the
range of addresses over which a memory access should generate a debug exception.
This patch utilizes the "mask" feature of the xscale debug hardware to implement
the correct functionality of the length argument. Some limitations imposed by
the hardware are:
- The length must be a power of two, with a minumum of 4.
- Two data breakpoint registers are available, allowing for two watchpoints.
However, if the length of a watchpoint is greater than four, both registers
are used (the second for a mask value), limiting the number of watchpoints
to one.
This patch also removes a useless call to xscale_get_reg(dbcon) in
xscale_set_watchpoint() (value had already been read from the register cache,
and the same previously read value is then modified and written back).
I have been using and testing this patch for a couple days.
Questions, corrections, criticisms of course gratefully received.
If the flash has not yet been probed and GDB connects while the target is
running, the flash probe triggered by GDB's memory map read will fail. In
that case the returned memory map will be empty, causing a subsequent load
from within GDB to fail. There's not much you can do from GDB to recover,
other than a restart; a 'mon reset init' and manual 'mon flash probe' won't
help since GDB has already made up its mind about the memory map.
It seems there's no reason to require the target to be halted when probing
the flash. Remove the check to let a valid memory map be provided to GDB
even when connecting to a running target.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The The patch labeled "CFI CORE: bug-fix protect single sector" was merged
rged without some requested bugfixes. Most significantly it broke invariants
in the code, invalidating descriptions and changing the calling convention
for underlying drivers. (It (Also wasn't CFI-specific...)
Fix that, and Include an update from Antonio Borneo for the degenerate
"nothing to do" case, (although that's still in the wrong location. which
is presumably why that is it was working in some cases but not all.)
src/flash/nor/core.c | 21 ++++++++++++++++-----
1 file changed, 16 insertions(+), 5 deletions(-)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Arguments for "flash bank" command are already
parsed and put in "bank" struct.
Removed code to parse them again.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Syntax of "flash bank" command requires:
- chip_width as CMD_ARGV[3]
- bus_width as CMD_ARGV[4]
Actual code swaps the arguments.
Bug has no run time impact since wrong variables
are only used to check value and both are checked
against same constraint.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch fixes the xscale_analyze_trace() function. This function was
defective for a trace collected in 'fill' mode (hiccups with repeated
instructions) and completely broken when buffer overflowed in 'wrap' mode. The
reason for the latter case is that the checkpoint registers were interpreted
incorrectly when two checkpoints are present in the trace (which will be true in
'wrap' mode once the buffer fills). In this case, checkpoint1 register will
contain the older entry, and checkpoint0 the newer. The original code assumed
the opposite. I eventually gave up trying to understand all the logic of the
function, and rewrote it. I think it's much cleaner and understandable now. I
have been using and testing this for a few weeks now. I'm confident it hasn't
regressed in any way.
Also added capability to handle (as best as possible) the case where an
instruction can not be read from the loaded trace image; e.g., partial image.
This was a 'TODO' comment in the original xscale_analyze_trace().
Outside of xcsale_analyze_trace(), these (related) changes were made:
- Remove pc_ok and current_pc elements from struct xscale_trace. These elements
and associated logic are useless clutter because the very first entry placed
in the trace buffer is always an indirect jump to the address at which
execution resumed. This type of trace entry includes the literal address in
the trace buffer, so the initial address of the trace is immediately
determined from the trace buffer contents and does not need to be recorded
when trace is enabled.
- Added num_checkpoints to struct xscale_trace_data, which is necessary in order
to correctly interpret the checkpoint register contents.
- In xscale_read_trace()
- Fix potential array out-of-bounds condition.
- Eliminate partial address entries when parsing trace (can occur in wrap mode).
- Count and record number of checkpoints in trace.
- Added small, inlined utility function xscale_display_instruction() to help
make the code more concise and clear.
TODO:
- Save processor state (arm or thumb) in struct xscale_trace when trace is
enabled so that trace can be analyzed correctly (currently assumes arm mode).
- Add element to struct xscale_trace that records (when trace is enabled)
whether vector table is relocated high (to 0xffff0000) or not, so that a
branch to an exception vector is traced correctly (curently assumes vectors
at 0x0).
+ virt2phys() can now convert virtual address to real
+ read_memory() and write_memory() are renamed to read_phys_memory()
and write_phys_memory()
+ new read_memory() and write_memory() try to resolve real address if
mmu is enambled than perform real address reading/writing
+ if address is bellow 0xc000000 than TTB0 is used for page table
dereference, if above - than TTB1. Linux style of user/kernel address
separation
+ if above fails (i.e address is unspecified) than mode is checked
whether it is Supervisor (than TTB1) or User (than TTB0)
- Software breakpoints doesn't work. You should invoke
"gdb_breakpoint_override hard" before you start debugging
+ cortex_a8_mmu(), cortex_a8_enable_mmu_caches(),
cortex_a8_disable_mmu_caches() are implemented
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I'm not sure what caused this significant character to get deleted.
it may be related to intermittent Editor or terminal flakes I've
been seeing lately (sigh). This fix is trivial.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fixing one bug can easily uncover another .... in this case,
making sure that we properly invalidate some cached NOR state when
resuming arbitrary target code turned up an issue when the code
wasn't quite arbitrary (and we couldn't know that, but some parts
of OpenOCD assumed the cache would not be invalidated.
Specifically: some flash drivers (like CFI) update that state in loops
with downloaded algorithms, thus invalidating the state as it's probed.
+ Add a new target state flag, to record whether the target is
running downloaded algorithm code.
+ Use that flag to add a special case: "trust" downloaded algorithms
not to corrupt that cached state, bypassing cache invalidation.
Also update some of the documentation to stipulate that this flavor of
trustworthiness is now *required* ... not just a fortuitous acident.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For some reason there are *two* schemes for interposing logic into
the run_algorithm() code path... One is a standard procedural wapper
around the target method invocation.
the other (superfluous) one hacked the method table by splicing
a second procedural wrapper into the method table. Remove it:
* Rename its slightly-more-featureful wrapper so it becomes
the standard procedural wrapper, leaving its added logic
(where it should have been in the first place.
Also add a paranoia check, to report targets that don't
support algorithms without traversing a NULL pointer, and
tweak its code structure a bit so it's easier to modify.
* Get rid of the superfluous/conusing method table hacks.
This is a net simplification, making it simpler to analyse what's
going on, and then interpose logic . ... by ensuring there's only one
natural place for it to live.
------------
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Without this, a system using gcc (GCC) 4.2.4 (Ubuntu 4.2.4-1ubuntu4)
aborts builds after reporting:
tcl.c: In function ‘handle_irscan_command’:
tcl.c:1168: warning: passing argument 1 of ‘buf_set_u32’ discards qualifiers from pointer target type
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Problem: halt at a breakpoint, enable trace buffer ('xscale trace_buffer enable
fill'), then resume. Wait for debug exception when trace buffer fills (if not
sooner due to another breakpoint, vector catch, etc). Instead, never halts.
When halted explicitly from OpenOCD and trace buffer dumped, it contains only
one entry; a branch to the address of the original breakpoint. If the above
steps are repeated, except that the breakpoint is removed before resuming, the
trace buffer fills and the debug exception is generated, as expected.
Cause: related to how a breakpoint is stepped over on resume. The breakpoint is
temporarily removed, and a hardware breakpoint is set on the next instruction
that will execute. xscale_debug_entry() is called when that breakpoint hits.
This function checks if the trace buffer is enabled, and if so reads the trace
buffer from the target and then disables the trace (unless multiple trace
buffers are specified by the user when trace is enabled). Thus you only trace
one instruction before it is disabled.
Solution: kind of a hack on top of a hack, but it's simple. Anything better
would involve some refactoring. This has been tested and trace now works as
intended, except that the very first instruction is not part of the trace when
resuming from a breakpoint.
TODO: still many issues with trace: doesn't work during single-stepping (trace
buffer is flushed each step), 'xscale analyze_trace' works only marginally for
a trace captured in 'fill' mode, and not at all for a trace captured in 'wrap'
mode.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Clean up the jtag/tcl.c file, which was one of the biggest and
messiest ones in that directory. Do it by splitting out all the
generic adapter commands to a separate "adapter.c" file (leaving
the "tcl.c" file holding only JTAG utilities).
Also rename the little-used "jtag interface" to "adapter_name", which
should have been at least re-categorized earlier (it's not jtag-only).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The command "flash bank" has updated syntax.
Add the mandatory parameter <target> to the usage message
that prints in case of error.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
first cut peek/poke over tcp/ip, used for debug/research
purposes only. Long term JTAG over TCP/IP might be an
offshoot. The performance is usable for development/testing
purposes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I don't know when "poll off" broke, but "poll off" didn't
stop background polling of target. The polling status flag
simply wasn't checked in the handle_target timer callback.
All target polling(including power/reset state) is now stopped
upon "poll off".
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
For testing and checking the build this can be useful,
it doesn't have any practical application outside development.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The init cleanup patch overlooked a message which was
wrongly specific to the "usbjtag" layout. Fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch fixes xscale software breakpoints by cleaning the dcache and
invalidating the icache after the bkpt instruction is inserted or removed. The
icache operation is necessary in order to flush the fetch buffers, even if the
icache is disabled (see section 4.2.7 of the xscale core developer's manual).
The dcache is presumed to be enabled; no harm done if not. The dcache is also
invalidated after cleaning in order to safeguard against a future load of
invalid data, in the event that cache_clean_address points to memory that is
valid and in use.
Also corrected a confusing typo I noticed in a comment.
TODO (or not TODO...?): the xscale's 2K "mini dcache" is not cleaned. This
cache is not used unless the 'X' bit in the page table entry is set. This is a
proprietary xscale extension to the ARM architecture. If a target's OS or
executive makes use of this for memory regions holding code, the breakpoint
problem will persist. Flushing the mini dcache requires that 2K of valid
cacheable memory (mapped with 'X' bit set) be designated by the user for this
purpose. The debug handler that gets downloaded to the target will also need to
be extended.
In the ft2232 driver, initialization for many layouts punts to a routine
called usbjtag_init(), instead of a routine specific to each layout.
That routine is a mess built around a "what type layout am I" core.
That's a bad design ... in this case, especially so, since it bypasses
the layout-specific dispatch which was just done, and obfuscates the
initialization which is at least somewhat generic, instead of being
specific to the "usbjtag" layout.
Split and document out the generic parts of usbjtag_init(), and make
the rest of those layouts have layout-specific init methods. Also,
rename usbjtag_reset() ... that also was not specific to the "usbjtag"
layout, and thus contributed to the previous code structure confusion.
(Eventually, all layout-specific code (and method tables) should probably
live in files specific to each layout. These changes will facilitate
those and other cleanups to this driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
the handling of caches, should be moved into the breakpoint
specific callbacks rather than being plonked into generic
memory write fn's.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Note that the FT4232 chips have four channels not two, and
Elaborate on uses of the additional channels.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The implementation is now more straightforward as the
scan_fields have been greatly simplified over time.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Øyvind Harboe
Antonio Borneo
Thomas Koeller
gcembed
Jon Povey
Spencer Oliver
Gary Carlson
Jun Ma
Jun Ma
Karl Kurbjun
Matthias Bode
Tobias Ringström
Mike Dunn
michal smulski
Andreas Fritiofson
David Brownell
Anton Fedotov
Daniel Bäder