(error: declaration of ‘pHDev’ shadows a global declaration; ../../../../src/jtag/drivers/rlink.c:102: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
in jim.c (error: declaration of ‘boolean’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:52: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
copy & paste error + added FIFO throttling to work around
lockup bug in FPGA.
The arm11 optimisation was introduced post v0.4.0, so this
is not a regression compared to previous release.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Helper ./src/helper/membuf.c is only used in at91sam3.c
1) Replace membuf with LOG_*
2) The original code in sam3_GetDetails() invalidates
all the buffered output of sam3_GetInfo(). The new
code skips sam3_GetInfo() if its output should not
be printed.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I think this fixed an error message where the error
message would show the *previous* uc code rather than
the current unsupported uc code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when the verify failed, it didn't return an error,
which breaks e.g. tcl scripts that rely on this for
exceptions to work.
Found by -Wshadow
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this batch of fixes should be pretty straightforward
rename of 'index' and an 'i' local variable shadowing.
'index' conflicts with a global name.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
found by code inspection. There are many other places in
CFI where LOG_ERROR() should be called similarly...
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when a write/unlock/erase failed during write_image, then
an error was not propagated back up so e.g. flash write
image from tcl scripts would not throw an exception.
Also flash filling speed was printed even when the
operation failed. Output is now less confusing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
failure to write to memory was not propagated.
This is an interesting case of broken error handling:
with exceptions we wouldn't have had this at all,
and I also wonder if there is a GCC option to warn
about these kinds of potential bugs.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Parameter "type" of function armv4_5_mmu_translate_va()
is now not used.
Remove the parameter and the "enum" listing its values.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function armv4_5_mmu_translate_va() now properly signals
errors in the return value.
Remove former error handling by setting variable "type" to
value "-1".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Function arm920t_write_memory() default return value
should be ERROR_OK.
All cases of local errors are handled immediately and
not further propagated.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit 0538081246
introduces a compile time warning:
arm920t.c: In function ‘arm920t_write_memory’:
arm920t.c:567: warning: ‘retval’ may be used uninitialized in this function
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
any read/write operation to memory can fail.
block write algorithm error propagation was broken
in that it would continue after an error was reported
writing data to ram or the algorithm failing.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
JTAG_MOVESTATE is misleading, this cmd is only used
for reset.
JTAG_PATHMOVE should be used otherwise.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hello,
"stm32x mass_erase" return ERROR_OK even if something goes wrong.
Here is a summary of changes :
* in stm32x_mass_erase : return ERROR_FLASH_OPERATION_FAILED when error
detected in FLASH_SR register;
* in COMMAND_HANDLER(stm32x_handle_mass_erase_command) : return the
returned value of stm32x_mass_erase().
I don't know if there is reason to always return ERROR_OK ?
Gaëtan
ETM analyze produced no output when the trace buffer was empty.
This patch provides users with a clue.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When a flash cmd is called using the flash name the autoprobe
function is not called. autoprobe is called if flash_command_get_bank
falls through to get_flash_bank_by_num.
This makes both get_flash_bank_by_name and get_flash_bank_by_num
behave the same.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Every time command "flash probe #" is executed, memory
structures are re-allocated without preventive free()
of former areas, causing memory leak.
Also, memory allocation does not check return value,
determining segmentation fault in case of out of memory.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
We request a id register read at the end of ahbap_debugport_init
but we never actually run the queue. In some cases this causes a
segfault.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch add support of iMX27 nand flash controller. This is based on
driver for imx31 nand flash controller.
OOB functionality is not fully working. As in mx31 controller, mx2 NFC
has a bug that swap two bytes between SPARE and MAIN buffer.
I used this driver for several months and no problems appear.
This second half of the patch is proposed to clean up some GDB keep alive
issues on arm7_9 targets that start up with very slow clocks. If an attempt
is made to write to key registers on the processor with a slow jtag speed,
GDB timeout warnings appear on the console (at least mine) when "reset halt"
or "reset init" commands are issued from the gdb client:
*** BEFORE PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1026). Workaround: increase "set remotetimeout" in GDB
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1027). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1006). Workaround: increase "set remotetimeout" in GDB
keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not
sent! (1004). Workaround: increase "set remotetimeout" in GDB
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
I added additional keep alive steps in areas that troubleshooting revealed
were causing problems. I only did this however for non-fast write memory
accesses. I don't think most people would be using fast memory accesses to
write to memory when the jtag and system clocks are slow anyway.
If you disagree with my feeling, think there is a more elegant way to handle
the problem, or think the patch will cause other unforeseen problems with
other targets, let me know. As you can see below, the patch does eliminate
the problem on my development station and I suspect that it will benefit
others.
*** AFTER PATCH ***
(gdb) monitor reset init
fast memory access is disabled
2 kHz
JTAG tap: at91sam9g20.cpu tap/device found: 0x0792603f (mfg: 0x01f, part:
0x7926, ver: 0x0)
target state: halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x000000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
RCLK - adaptive
dcc downloads are enabled
fast memory access is enabled
NAND flash device 'NAND 256MiB 3,3V 8-bit' found
(gdb)
Gary Carlson
Gary Carlson, MSEE
Principal Engineer
Carlson-Minot Inc.
tcl "puts" didn't work because the logging code sensored strings
that did not include a '\n'. The correct thing is to sensor
empty strings, which are used to keep gdb connection alive.
The tcl "puts" code broke apart strings which do contain '\n' in
order to implement the -nonewline argument, which is how it
got hurt by the bug in log.c
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Page reads using hwecc4_infix layout segfaulted for check_bad_blocks because
the read assumed a valid data buffer, which check_bad_blocks does not use
(it only passes a 6 byte buffer for the start of OOB).
This version copes with undersized or missing data or oob buffers and uses
random read commands within the page to skip unwanted areas of data/OOB for
speed.
NOTE: Running check_bad_blocks with this layout will be reading infix
OOB locations, not manufacturer bad block markers. This means that if you
check blocks written in infix layout they will appear good, but manufacturer-
marked bad blocks may also appear good.
If you want to scan for manufactuer-marked bad blocks, you need to enable
raw_access before running check_bad_blocks, or use the non-infix layout.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
CC: David Brownell <dbrownell@users.sourceforge.net>
nand_build_bbt() was ignoring the return value from nand_read_page() and
blindly continuing.
It now passes the return value up to the caller if the read fails.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Change download rate messages about kibibytes from "kb/s" to "KiB/s" units.
See: http://en.wikipedia.org/wiki/Data_rate_units
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Remove few LOG_DEBUG() messages, together with code and
variables required to build such messages.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final step to force bus_width size during CFI flash
read.
Added CFI specific implementation cfi_read() that uses
only accesses at bus_width size.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Final target is to force bus_width size during CFI flash
read.
In this first step I need to replace default flash read
with flash specific implementation.
This patch introduces:
- flash_driver_read() layer;
- default_flash_read(), backward compatible;
- read() callback in struct flash_driver;
- proper initialization in every flash_driver instance.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
During cfi_write(), head and tail of destination area
could be not aligned to bus_width.
Since write operation must be at bus_width size, source
buffer size is extended and buffer padded with current
values read from flash.
Force using bus_width to read current value from flash.
Do not use cfi_add_byte() anymore, to allow removing this
function later on.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
NOR flash structure requires each access to be bus_width wide.
Fix read of flash ID accordingly to rule above.
Add case (chip_width == 4), allowed by CFI spec and coherent
with current value of CFI_MAX_CHIP_WIDTH but currently not
used by any target.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Since NOR flash devices does not handle "byte enable lanes",
each read/write access involves the whole "chip_width".
When multiple devices are in parallel, usually all chips are
enabled during each access.
All such cases are compatible with flash accesses at
"bus_width" size.
Access at "bus_width" size is mandatory for write access to
avoid transferring of garbage values to flash.
During read access the flash controller should take care,
and discard unneeded bytes. Anyway, it is good practice to
use "bus_width" size also for read.
Every memory access that does not respect "bus_width" size
is marked with a "FIXME" comment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Review and simplify computation of bufferwsize.
Add comments about variables' meaning.
The same code is present 3 times in the file.
Current patch updates all the 3 instances.
Step 1)
Replace "switch(bank->chip_width) {...}".
Illegal values of bank->chip_width are already dropped.
For legal values, the code is equivalent to:
bufferwsize = buffersize / bank->chip_width;
Step 2)
The above code replacement plus the following line:
bufferwsize /= (bank->bus_width / bank->chip_width);
is merged in a single formula:
bufferwsize = (buffersize / bank->chip_width) /
(bank->bus_width / bank->chip_width);
and simplified as:
bufferwsize = buffersize / bank->bus_width;
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Arguments chip_width and bus_width of command "flash bank" are
not fully checked.
While bus_width is later on redundantly checked in several other
parts (e.g. in cfi_command_val()) and generates run-time error,
chip_width is never checked, nor related to actual bus_width
value.
Added check to avoid:
- (chip_width == 0), that would mean no memory chip at all,
avoiding also division by zero e.g. in cfi_get_u8();
- (bus_width == 0), that would mean no bus at all;
- unsupported cases of chip_width or bus_width value not power
of 2;
- unsupported case of chip width wider than bus.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Last block was being skipped, fix by changing the loop test from "<" to "<="
First block argument was ignored, always started from block 0 (and counted
the wrong blocks as bad if first was nonzero). Now we use it.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The last_block argument to nand_erase() is checked against nand->num_blocks,
but the highest valid block number is (total - 1), the test for invalid should
be ">=" rather than ">".
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Freddie Chopin
Antonio Borneo
Oyvind Harboe
Thomas Koeller
gcembed
Jon Povey
Spencer Oliver
Gary Carlson
Jun Ma