As with single stepping, the previous stuff was needed because
the ARM11 code wasn't using the standard ARM base type and
register access ... but now those mechanisms work, so we can
switch out that special-purpose glue, in favor of the more
thoroughly tested/capable "standard" code.
Fixes a bug in the resume() implementation: it wasn't handling
two of its arguments correctly, preventing the "flash erase_check"
algorithm from working. (This code needs a *subsequent* update
for correct register handling, though... removing the confusion
about which "r2", for example, to use.)
This should resolve some "FIXME" comments too, for Thumb and
processor mode support. It also gets rid of a nasty exit()
call; servers should only have *clean* shutdown paths.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The previous stuff was needed because the ARM11 code wasn't using
the standard ARM base type and register access ... but now those
mechanisms work, so we can switch out that special-purpose glue.
This should resolve all the "FIXME -- handle Thumb single stepping"
comments too, and properly handle the processor's mode. (Modulo
the issue that this code doesn't yet handle two-byte breakpoints.)
Clarify the comments about the the hardware single stepping. When
we eventually share breakpoint code with Cortex-A8, we can just make
that be the default on cores which support it. We may still want an
override command, not just to facilitate testing but to cope with
"instruction address mismatch" not quite being true single-step.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This provides "standard" ARM register support -- with twenty or
more shadow registers on top of what this code now handles, but
properly associated with the various core modes -- parallel to
the current register code. That is, the current code is stilil
managing the "current" registers; the new code shadows them.
You can see all the registers with "arm reg", modify the shadows
like "r8_fiq" or "sp_abt" with "reg", and see them get properly
written back when you step. (Just don't do that with any of the
registers managed by the "old" code ...)
It also switches to using more standard code, relying on those
standard registers, in two places: (a) the poll status display,
which now shows core state (ARM/Thumb/...) and mode (Supervisor,
IRQ, etc); and (b) GDB register access.
So it's not a full migration, there are warts -- every place that
touches the old register cache is a potential bug -- but it's a
small more-or-less-comprehensible step that's even somewhat useful.
Later patches complete the migration.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This was a private mechanism to snapshot registers before leaving
debug state, and then on reentry to optionally display what changed.
It was coupled to the private register cache, which won't be sticking
around in that form for much longer. Remove (instead of teaching
it how to handle *all* the registers).
(The idea is interesting, but we ought to be able to implement
this in a generic way. Ideally through Tcl scripts that can
automatically be invoked following debug entry...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is a very thin layer over some of the current ARM11
debug TAP utilities. The layer isn't yet hooked up.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
First version of interface for sharing code between ARMv6 and ARMv7a
debug modules ... now the architecture includes debug support. (Not
the same as for the trimmed-down v7m or v6m though!) This is a first
version of an interface that will let the ARM11 and Cortex-A8 support
share code, features, and bugfixes. Based on existing code from both
of those cores.
The ARM v7-AR architecture specification calls this commonality the
"Debug Programmer's Model (DPM)", which seemed to be an appropriate
acronym -- a TLA even! -- for use in our code. Made it so. :)
The initial scope of this just supports register access, and is geared
towards supporting top level "struct arm" mechanisms. Later, things
like breakpoint and watchpoint support should be included.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For now there's no point in saving this stuff after examine()
checks it out as OK. Ditto exporting symbols that aren't
used outside of the module which defines them. In fact, those
two things needlessly complicate the code...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make this code look more like the rest of the OpenOCD code.
- Use calloc() directly, not NEW() ... and fix some potential
memory leaks while we're at it.
- Remove FNC_INFO ... it's a NOP that just clutters things,
and it's trivial for developers to add tracing as needed.
- Replace FNC_INFO_NOTIMPLEMENTED with LOG_WARNING calls;
ditto. And stop having those call sites wrongly succeed!
- Waste less space with the CHECK_RETVAL() macro.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This will allow data to be allocated in read only
memory instead of on the stack. Speeds things up
and reduces stack usage.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
buf_set_u32() operated on an uninitialized stack
variable with non-byte boundaries, which led to
warnings about reading uninitialized stack.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Start using the arm_reg_current() call. This shrinks and speeds
the affected code. It can also prevent some coredumps coming from
invalid CPSR values ... the ARMV4_5_CORE_REG_MODE() macro returns
bogus registers if e.g. "Secure Monitor" mode isn't supported by
the current CPU.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We don't need to use size_t in these places; so it's easy
to be rid of the need for this #ifdef and its MS-derived
portability problems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
With -O3 when inlining aggressively the total stack usage will
be the sum of many fn's, which can easily get out of hand.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Have arm_set_cpsr() handle the two core state flags, updating
the CPU state. This eliminates code in various debug_entry()
paths, and marginally improves handling of the J bit.
Catch and comment a few holes in the handling of the J bit on
ARM926ejs cores ... it's unlikely our users will care about
Jazelle mode, but we can at least warn of Impending Doom. If
anyone does use it, these breadcrumbs may help them to find
the right path through the code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Define arm_reg_current() ... returning handle to a given register,
and encapsulating the current mode's register shadowing. It's got
one current use, for reporting the current register set to GDB.
This will let later patches clean up much ARMV4_5_CORE_REG_MODE()
nastiness, saving a bit of code.
Define and use arm_set_cpsr() ... initially it updates the cached
CPSR and sets up state used by arm_reg_current(), plus any SPSR
handle. (Later: can also set up for T and J bits.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Stash a pointer to the CPSR in the "struct arm", to help get rid
of the (common) references to its index in the register cache.
This removes almost all references to CPSR offsets outside of the
toplevel ARM code ... except a pair related to the current ARM11
"simulator" logic (which should be removable soonish).
This is a net minor code shrink of a few hundred bytes of object
code, and also makes the code more readable.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Minor cleanup of ARM11 register handling: remove disabled
register hooks. This should all be handled by shared code,
and this stuff is just clutter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Implementations need to access the register struct they modify;
make it easier and less error-prone to identify the instance.
(This removes over 10% of the ARMV4_5_CORE_REG_MODE nastiness...)
Plus some minor fixes noted when making these updates: ARM7/ARM9
accessor methods should be static; don't leave CPSR wrongly marked
"dirty"; note significant XScale omissions in register handling;
and have armv4_5_build_reg_cache() record its result.
Rename "struct armv4_5_core_reg" as "struct arm_reg"; it's used
for more than those older architecture generations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove two commands that were documented as "debug commands"
and where "you probably don't want to use this". We never
intended to support them, and at least one problem report
boiled down to using this when it shouldn't have been used.
Update the docs on the existing register commands to talk a
bit more about register access and cache behavior. (Those
debug commands existed largely to *bypass* the cache.) And
fix some minor doc goofs that snuck in with recent changes,
renaming "armv4_5" as "arm" and "arm9tdmi" as "arm9".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The previous version never wrote dirty registers
for non-current CPU modes ... fix that.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We *should* be able to read and write registers in any core mode,
instead of being stuck with whatever mode the core was when we
entered debug state. This patch makes them work.
Note that the current restore_context() only handles the current
mode; writing to other-mode registers is a NOP without a followup
patch fixing that. Also, that SPSR access needed some bugfixes;
it was confused with CPSR.
Secure monitor mode also seems dubious; there's probably more to
be done before that's sufficiently understood by the debugger.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Create a generic register_cache_invalidate(), and use it to
replace three all-but-identical core-specific routines:
- armv4_5_invalidate_core_regs()
- armv7m_invalidate_core_regs
- mips32_invalidate_core_regs() too.
Make cache->num_regs be unsigned, avoiding various errors.
Net code shrink and simplification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Just pre-allocate memory for the cached register value.
Shrinks heap overhead; increases locality-of-reference.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Combine register names with other per-register data into a
single template structure. This saves space, and makes it
easier to change how registers get handled (by shrinking
the number of places that care about cache indices).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The examine() method has some conceptual breakage. Cope
with it by manually splitting out the run-once parts from
the after-each-reset parts ... this gets rid of memory
leaks and speeds up resets after the first one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We don't want an ARMv7-specific core state enumeration just to
add ThumbEE state. Update the generic stuff to handle that,
and replace the V7-specific bits with it.
For Cortex-A8: on debug entry, check both the T and J bits
instead of just the T bit. When the J bit is set, set the
right state and warn appropriately.
(And while we're at it, move the generic arm struct to the front
of the v7a structure, for somewhat better code generation.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The only way ARMv7-A modes differ from ARMv4/ARMv5 flavors
is that v7-A is allowed to include "Secure monitor" support.
That's now handled by our standard top-level ARM code ... so
phase out the stuff that's specific to ARMv7-A.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Removing the fast command eliminates the fast_and_dangerous global,
which was used only by arm7_9_common as an initializer. The command
is not called in the tree; instead, more explicit commands are used.
The jim_global_long function was not used anywhere in the tree.
Rewrite arm11_handle_bool to provide a generic on/off command helper.
Refactors COMMAND_PARSE_BOOL to use new command_parse_bool helper,
which gets reused by the new command_parse_bool_any helper.
This later helper is called by the new command helper function to
accepts any on/off, enable/disable, true/false, yes/no, or 0/1 parameter.
Updates all command parsing of simple "enable" and "disable" arguments.
A few case in the tree use a tri-state or extended arguments, which
cannot use this simple macro.
Simlifies the xscale icache/dcache command handler logic.
Change the layout to show the "Secure Monitor" registers too,
when they're present.
Instead of lining registers for each of six (or seven) modes up
in adjacent vertical columns, display each mode's registers (or
shadows) in a single block, avoiding duplicate value displays.
This also lets us shrink the line length to fits in standard 80
character lines ... six or seven 18-character columns can't fit.
Relabel "r13" as "sp", so it's more meaningful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
When we read the CPSR on debug entry, update the CPSR cache in all
cases, not just when the current processor state is User or System.
Plus minor cleanup of how the (too-many) other registers' cache
entries get updated.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
If the core doesn't provide an optimized version of this
method, provide one without core-specific optimizations.
Use this to make Cortex-A8 support the "arm reg" command.
Related: make the two register access methods properly static,
have the "set" log a "not halted" error too, and make sure
that the "valid" flag is set on successful reads.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
ARMv7-A doesn't need to duplicate all the standard ARM code
for register handling.
- Switch Cortex-A8 to use the standard register code
- Remove duplicated infrastructure from ARMv7-A
- Have ARMv7-A arch_state() show CPSR, like other ARMs
Add comments to show where the Cortex-A8 isn't actually doing
the right thing for register reads/writes, unless core happens
to be in the right mode to start with. (Looks like maybe there
may be generic confusion between saved/current PSR values in all
the ARM code ...)
Make related ARMv7-A and Cortex-A8 symbols properly static.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Teach the "armv4_5" register code to understand about the
secure monitor mode:
- Add the other three shadowed registers to the arrays
- Support another internal mode number (sigh) in mappings
- Catch malloc/calloc failures building that register cache
This should kick in for Cortex-A8 and ARM1176.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's used to flag cores with the "TrustZone" extension,
and is used in subsequent patches to set up support for
the registers shadowed by its new secure monitor mode.
The ARM1176 and Cortex-A8 both support this new mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Moves definitions for each layer into their own file, eliminating
layering violations in the built-in TCL code. Updates src/Makefile.am
rules to include all files in the final startup.tcl input file, and
others Makefile.am rules to distribute the new files in our packages.
The recent migration broke them, the fixes broken them in a new way,
but this should restore them to working order. Eliminates the
temporary variable, as the CMD_NAME macro can once again be use
in routines that increment CMD_ARGV without nasty side-effects.
Also, this is on the path to increasing the word size for
bit vectors from 8 to something wider(32? natural host machine
width?)
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add a new is_arm_mode() predicate, and use it to replace almost
all calls to current armv4_5_mode_to_number().
Eventually those internal mode numbers should vanish... along
with their siblings in the armv7a.c file.
Remove a handful of superfluous checks ... e.g. the mode number
was just initialized, or (debug entry methods) already validated.
Move one of the macros using internal mode numbers into the only
file which uses that macro. Make the tables manipulated with
those numbers be read-only and, where possible, static so they're
not confused with part of the generic ARM interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add and use arm_mode_name() to map from PSR bits to user
meaningful names. It uses a new table which, later, can
be used to hold other mode-coupled data.
Add definitions for the "Secure Monitor" mode, as seen on
some ARM11 cores (like ARM1176) and on Cortex-A8. The
previous mode name scheme didn't understand that mode.
Remove the old mechanism ... there were two copies, caused
by Cortex-A8 needing to add "Secure Monitor" mode support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
All ARM cores need to provide obsolete FPA registers in their
GDB register dumps. (Even though cores with floating point
support now generally use some version of VFP...)
Clean up that support a bit by sharing the same dummy registers,
and removing the duplicate copies. Eventually we shouldn't need
to export those dummies.
(This makes the ARMv7-M support include the armv4_5 header, and
cleans up related #includes, but doesn't yet use anything from
there except those dummies.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No need to indirect from registered integers to pointers.
Just stash the pointers directly in the register struct,
and don't even bother registering.
This is a small code shrink, speeds register access just
a smidgeon, and gets rid of another rude exit() path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
And move the rest of the vector_catch stuff into the C file;
it's not part of the module interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Also, switch integrity check over to the correct magic number,
and remove duplicate v4/v5 #define.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Have ARM11 register the "standard" ARM commands. For now, only
disassembly really works.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the "armv4_5" command prefix to straight "arm" so it makes
more sense for newer cores. Add a simple compatibility script.
Make sure all the commands give the same "not an ARM" diagnostic
message (and fail properly) when called against non-ARM targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use size_t instead of uint32_t when specifying file sizes. Update all
consumers up through the layers to use size_t when required. These
changes should be safe, but the higher-levels will need to be updated
further to receive the intended benefits (i.e. large file support).
Add error checking for fileio_read and file_write. Previously, all
errors were being silently ignored, so this change might cause some
problems for some people in some cases. However, it gives us the chance
to handle any errors that do occur at higher-levels, rather than burying
our heads in the sand.
Tweak "standard" ARM disassembler diagnostics to fail if the target
is not "an ARM" (vs. not "an ARMV4/5"), so it makes more sense for
cores inheriting this as the "generic" disassembler.
Also, to use the Thumb2 entry instead of the original Thumb entry.
This makes it work better for both newer cores (which support those
added instructions) and for BL and BLX instructions on older cores.
(Those instructions are 32-bits, which requires curious state-aware
code to go through a 16-bit decode interface...)
Plus minor cleanups, notably to have fewer exit paths and to make
sure they all return failure codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
They're really too big to inline, at least for code that's
not in any performance-critical loops.
Also move the associated string table to the rodata section.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't include it in more headers than necessary; just
use it in the few files that actually need it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The ARRAY_SIZE macro was defined in several target files, so move it
to types.h.
This patch also removes two other identical macros: DIM (from jtag.h)
and asizeof (from arm11.h).
Eliminate redundant check that gets covered by using unsigned type.
Created to eliminate noise from subsequent patches, but this kind of
conversion will be beneficial in similar ways throughout the tree.
The container_of macro is useful as a general solution. It belongs
in types.h, rather than target.h where it was introduced. Requires
the offsetof macro, which comes from <stddef.h> (moved as well).
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Lots of files still include it, often through needless
duplicate inclusion of "log.h"; sigh.
This cleans up the inclusion graph a bunch, so there are
fewer inclusion paths, but it doesn't change much otherwise.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
downloadable algorithms actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also: "algorithm.h" doesn't need to include "types.h" again;
it already comes from a different header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Now the ARM11 cores can use the renamed arm_checksum_memory()
and arm_blank_check_memory() routines ... do so.
Sanity checked with "flash erase_check" of both NOR banks on an
OMAP2420 ... the algorithm code dumped four lines of of "poll"
status after each of almost 520 blocks (yes, *very* annoying) but
gave plausible results after producing that spam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Three changes: remove ARM11_HANDLER() in favor of normal structure
initialization syntax; fix goofy indentation in that structure; and
don't needlessly export arm11_register_commands(), it's only called
through that method table.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The arm7_9_checksum_memory() and arm7_9_blank_check_memory()
routines are not actually specific to the ARM7 and ARM9 core
generations ... they can work for any core which can run
algorithms using basic ARM (not Thumb) instructions.
Rename them; move the declarations to a more generic site;
likewise move the code (and tidy it a bit in the process).
NOTE: the blank_check() method falsely returned a success
status (0) on one error path, when the algorithm failed.
Fixed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously this flag was stored in "target_type", so that for example
if there were two ARM7TDMI targets in a scan chain, both would claim
to have been examined although only the first one actually had its
examine() method called.
Move this state to where it should have been in the first place, and
hide a method that didn't need exposure ... the flag is write-once.
Provide some doxygen. The examine() method is confusing, since it
isn't separating one-time setup from the after-each-reset stuff. And
the ARM7/ARM9 version is, somewhat undesirably, not leaving the debug
state alone after reset ... probably more of an issue for trace setup
than for watchpoints and breakpoints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Removes unused arm_jtag_buf_* helpers from arm_jtag.[ch]. These could
reappear if patches are provided to conver the tree to use them, but
this code should not be in the master tree until that series is ready.
This fixes an issue due to the new command handler syntax caused by the mw handler playing with the args pointer before
using the CMD_NAME macro. Fix is to move this call above the lines changing args.
Changed some printf format strings..
[dbrownell@users.sourceforge.net: shrink lines, fix indents]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Kick in ETM (and ETB) support for ARM11. Tested on OMAP 2420,
so update that configuration. (That's an ARM1136ejs, ETB,
OpenGL ES1.1, C55x DSP, etc.)
Also update the other ARM11 ETM + ETB targets in the tree
to set up these modules. (Not tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
These aren't desirable, given "standard" ETM support.
Also remove the now-unused arm11_find_target().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No point in having two identical examine methods for the
ARM7TDMI and ARM9TDMI drivers; move, rename, shrink, share.
Add a bit of doxygen; stop needlessly exporting a method.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Return NULL from etm_build_reg_cache() not ERROR_OK; and share
code on that fault path.
Let ETM code handle any tracking of its cache -- not callers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This will enable reusing many common ARM utilities, in
particular the ETM and ETB support. The ARM11 support
can still be much simplified after this patch, though.
Note: none of those common utilities kick in yet...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We have too many different registers, and too many version and
context dependent interpretations, for this type of bitfield
management to be scalable.
(Anyone who really wants bitfield interpretation *can* do that
in Tcl code...)
There are ... quite a few copies of the same ARM dummy registers.
There should eventually be one copy; this many is craziness.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove the last external user of arm7_9_get_arch_pointers(), and
that annoying downcast utility. Add an is_arm7_9() predicate.
Stop returning specious success codes on various failure paths
in the ARM7/ARM9 commands which used that downcast utility.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The number of command arguments will always be 0 or more, so use
the right type in handlers. This has a cascading effect up through
the layers, but the new COMMAND_HANDLER macros prevented total chaos.
By using CALL_COMMAND_HANDLER, parameters can be reordered, added, or
even removed in inherited signatures, without requiring revisiting
all of the various call sites.
David Brownell
Jerry Ling
Øyvind Harboe
Zachary T Welch
Krzysztof Dziuba
Dean Glazeski
Ferdinand Postema