OpenOCD project is switching to SPDX tags.
Replace the few FSF boilerplate in tcl folder.
Change-Id: I15b146eb77cc491ed7355178f684f3e76fc763b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7025
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add Ampere Altra ("Quicksilver") and Ampere Altra Max ("Mystique")
target/board configuration files.
The target configuration file supports silicon and emulation.
The board configuration files support 1 and 2 socket platforms.
Tested on Ampere emulation and silicon
Change-Id: I036c798a50624e30ab51ccd2895b6f60c40be096
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5591
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
ESP32-S2 is a single core Xtensa chip.
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I2fb32978e801af5aa21616c581691406ad7cd6bb
Reviewed-on: https://review.openocd.org/c/openocd/+/6940
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This commit is adapted from [1].
[1] https://review.openocd.org/c/openocd/+/4999
Signed-off-by: Michael Walle <michael.walle@kontron.com>
Signed-off-by: Heiko Thiery <heiko.thiery@kontron.com>
[ adapted to use common configuration ]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I9a428371694e7864e03055b8de18a55a7843b8c2
Reviewed-on: https://review.openocd.org/c/openocd/+/6977
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added bluenrg-lps support
Added file for the board steval-idb012v1
Fixed size_info information using a mask
Changed the if condition in bluenrg-x.cfg to be valid only for bluenrg-1 and bluenrg-2
Signed-off-by: Salvatore Giorgio PECORINO <salvatore-giorgio.pecorino@st.com>
Change-Id: Ic0777ec0811ee6fac7d5e1d065c4629e47d84a1f
Reviewed-on: https://review.openocd.org/c/openocd/+/6928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace deprecated commands 'mem2array' and 'array2mem' with
new Tcl commands 'read_memory' and 'write_memory'.
Change-Id: I116d995995396133ca782b14cce02bd1ab917a4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6859
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the LS1046A Reference Design Board. There are
several JTAG headers accessable once the case is opened, but this config
is for the externally-accessable CMSIS DAP.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: I0f83470da3758f0c4512ce47348c4db7de17b27e
Reviewed-on: https://review.openocd.org/c/openocd/+/6855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Original TLC syntax uses 'set varname' to retrieve the value of
variable 'varname'. Such archaic syntax is still valid, but the
shorter '$varname' makes the code easier to read.
Replace 'set varname' with '$varname'.
While there, remove some useless curly brackets.
Change-Id: I27310e8c05afe56ea8bd0e41d4ae2c34447b725c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6863
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This adds a board file for the NXP LS1088ARDB. This only covers the
"primary" JTAG header J55, and not the PCIe header (J91). The only
oddity is that the LS1088A and CPLD are muxed by adding/removing a
jumper from J48. Unfortunately, it doesn't look like OpenOCD supports
this CPLD beyond determining the irlen, so it's not very useful. Those
who are interested in experimenting can define CWTAP to access the CPLD,
but the default is to access the CPU.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Change-Id: Ia07436a534f86bd907aa5fe2a78a326a27855a24
Reviewed-on: https://review.openocd.org/c/openocd/+/6849
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This board is (software wise) similar to the existing SAME54 Xplained
Pro board, with just a slightly different MCU. (Hardware wise, it
features a vastly different form factor.)
Signed-off-by: Jörg Wunsch <openocd@uriah.heep.sax.de>
Change-Id: I5e5435d49d333fb74471994ee84de59ed983153c
Reviewed-on: https://review.openocd.org/c/openocd/+/6747
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Axel W.
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32mp13x has one core Cortex-A7.
The board Discovery Kit includes an on-board STLink-V3 with SWD
connection.
The webpage of the board is not active yet.
Change-Id: I8836b26612a160ead79766955ebefaf3d21a329c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6675
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
do not force the presence of the reset line, since some custom boards
may do not contain the reset line.
Change-Id: I031ab34012b34a1b49def9db16461f9de0ae29cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Fleck <fleckz@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/316/
Reviewed-on: https://review.openocd.org/c/openocd/+/6506
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
known boards are NUCLEO-G431KB, NUCLEO-G431RB and NUCLEO-G474RE
note: this work safely with B-G431B-ESC1, B-G474E-DPOW1,
STM32G474E-EVAL and STM32G484E-EVAL
Change-Id: I132a97e1816620b182983edc8a4b272b52b9241d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5484
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
known boards are NUCLEO-G031K8, NUCLEO-G070RB, NUCLEO-G071RB
note: this work safely with STM32G0316-DISCO, STM32G071B-DISCO
and STM32G081B-EVAL
Change-Id: I483b6f44409228cd8c2c97b3c560927d1645c517
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5483
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Add support for ECP5 FPGA targets and board based on this chips:
Radiona ULX3S and Lambdaconcept ECPIX-5
Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6112
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add board configuration for Renesas Falcon board based on the R8A779A0 V3U SoC.
Change-Id: If8369f2e2b97dfea9ccbee2c9b916ef7094f9b92
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/6315
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.
Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
Fix manually the remaining lines that don't match simple patterns
and would require dedicated boring scripting.
Remove the 'expr' command where appropriate.
Change-Id: Ia75210c8447f88d38515addab4a836af9103096d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6161
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jimtcl commit 1843b79a03dd ("expr: TIP 526, only support a single
arg") drops the support for multi-argument syntax for the TCL
command 'expr'.
In the TCL scripts distributed with OpenOCD there are 1700+ lines
that should be modified before switching to jimtcl 0.81.
Apply the script below on every script in tcl folder. It fixes
more than 92% of the lines
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
#!/usr/bin/perl -Wpi
my $re_sym = qr{[a-z_][a-z0-9_]*}i;
my $re_var = qr{(?:\$|\$::)$re_sym};
my $re_const = qr{0x[0-9a-f]+|[0-9]+|[0-9]*\.[0-9]*}i;
my $re_item = qr{(?:~\s*)?(?:$re_var|$re_const)};
my $re_op = qr{<<|>>|[+\-*/&|]};
my $re_expr = qr{(
(?:\(\s*(?:$re_item|(?-1))\s*\)|$re_item)
\s*$re_op\s*
(?:$re_item|(?-1)|\(\s*(?:$re_item|(?-1))\s*\))
)}x;
# [expr [dict get $regsC100 SYM] + HEXNUM]
s/\[expr (\[dict get $re_var $re_sym\s*\] \+ *$re_const)\]/\[expr \{$1\}\]/;
# [ expr (EXPR) ]
# [ expr EXPR ]
# note: $re_expr captures '$3'
s/\[(\s*expr\s*)\((\s*$re_expr\s*)\)(\s*)\]/\[$1\{$2\}$4\]/;
s/\[(\s*expr\s*)($re_expr)(\s*)\]/\[$1\{$2\}$4\]/;
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I0d6bddc6abf6dd29062f2b4e72b5a2b5080293b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6159
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Both http://openocd.zylin.com/542/ and http://openocd.zylin.com/543/
introduce the same typo in the bitfield for initializing the l2
cache of imx53.
One year later, http://openocd.zylin.com/1461/ copy-pastes the same
typo.
The comment above the code show that it's really an error and not
the expected behaviour.
Fix the typo replacing the incorrect comparison '<' with a left
shift.
Change-Id: I43725731a2228e28a676215f76936fa289d9395e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e3b3273433 ("cfg: add imx53loco board config")
Fixes: 108a458ab8 ("cfg: add icnova_imx53_sodimm board config")
Fixes: e608ced330 ("ftdi/board: Add support for DENX M53EVK")
Reviewed-on: http://openocd.zylin.com/6156
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
Add board and target configuration files for
Ampere eMAG8180 board and Ampere eMAG processor.
Tested on an Ampere eMAG8180 development platform.
Change-Id: I222653f0fc12d25202a7e469db3594076cbc38ed
Signed-off-by: Anthony Ferranti <ferranti@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5569
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Antonio Borneo
Erhan Kurubas
Daniel Goehring
Sean Anderson
Salvatore Giorgio PECORINO
Marc Schink
Nishanth Menon
Jacek Wuwer
Hans-Erik Floryd
Joerg Wunsch
Tarek BOCHKATI
Wealian Liao
Oleksij Rempel
Jian-Hong Pan
Marek Vasut
Rohit Singh
Peter Lawrence
Felipe Balbi
Anthony Ferranti