OpenOCD cannot connect to BCM2711's JTAG interface on RPi 4B board until
the reset configuration mode is set as trst_only.
According to Table 94. GPIO Pins Alternative Function Assignment of
Broadcom's BCM2711 ARM Peripherals datasheet [1] and Raspberry Pi's GPIO
control in config.txt document [2], only Test Reset (TRST) pin (no
System Reset, SRST) is exposed.
[1] https://datasheets.raspberrypi.org/bcm2711/bcm2711-peripherals.pdf
[2] https://www.raspberrypi.org/documentation/configuration/config-txt/gpio.md
Change-Id: I806f0be9700fa0f0944b42c8a651a5731adc762b
Link: http://openocd.zylin.com/#/c/6364/1
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Reviewed-on: http://openocd.zylin.com/6367
Tested-by: jenkins
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The existing implementation blocks in select() for a fixed amount of
time. This change tracks when the next event (likely poll()) wants to be
run, and uses a shorter timeout in select() if necessary.
Also track all these timeouts using milliseconds as returned by
timeval_ms() instead of `struct timeval` to simplify the code.
This feature is helpful if poll() wants to do something like sample PCs
or memory values for basically the entire time that otherwise OpenOCD
would be hung in select(). See
https://github.com/riscv/riscv-openocd/pull/541 for an example of that.
The RISC-V code using this change will be upstreamed some day, too.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I67104a7cf69ed07c8399c14aa55963fc5116a67d
Reviewed-on: http://openocd.zylin.com/6363
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds documentation for the bcm2835 interface configuration
parameters to the user manual. Documentation format is based on
the FTDI interface section, and was taken from the descriptions
in the driver source code.
Change-Id: I77b09b8bd44d8e8fe9cc5fb9de3c3a30550d943c
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6376
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds support for the Blinkinlabs JTAG Hat, a Raspberry Pi
expansion board that provides JTAG and SWD connections via level-
shifting buffers.
Change-Id: I228bf6a18890b7c3d6679bbc63bfe39f726d8323
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6372
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Adds a new, optional configuration "bcm2835gpio_swdio_dir_num" to
the BCM2835 driver, to control the direction of an external buffer
driver IC in SWD mode. For example, this is needed to use a level-
shifting buffer, such as the SN74LVC2T45 used on the JTAG Hat
Change-Id: If5c146f310ecf8ceae85443b3670936467d2786d
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6371
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Commit fceb29d03f ("jtag/aice: use macros in place of const
variables") replaces some 'static const uint8_t' with macros.
This breaks the build on MacOS because the macro values are of
'int' type that doesn't match with the printf format 'PRIx8'.
error: format specifies type 'unsigned char' but the
argument has type 'int' [-Werror,-Wformat]
Replace the printf format 'PRIx8' with 'x'.
While there, remove a useless cast to uint32_t and fix the printf
format too.
Change-Id: Ib87298a61637b75a2813f209e5209d39ab2745f8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fceb29d03f ("jtag/aice: use macros in place of const variables")
Reviewed-on: http://openocd.zylin.com/6380
Tested-by: jenkins
Due to Freenode takeover it's likely that most of our users are going to
seek support on Libera in the nearest future.
Change-Id: I98db95bab51f4ef2ac854bf521468d22b2794e56
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6297
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Add identifiers of the Cortex-A76 ROM and debug unit.
Change-Id: Ieef0d990189d3c0502e8d530874dc9cbca4417d8
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6358
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Broadcom Brahma-B53 CPUs contains a number of custom ROM table
entries for its PMU, Debug unit, and a couple of ROM tables.
Change-Id: I1f21f07ed296579c374f24e781325789bf4ebf51
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6368
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new checkpatch can automatically fix the code, but this
feature is still error prone and not complete.
Patch generated automatically through the new checkpatch with
flags "--types CONSTANT_COMPARISON --fix-inplace".
Some Yoda condition is detected by checkpatch but not fixed; it
will be fixed manually in a following commit.
Change-Id: Ifaaa1159e63dbd1db6aa3c017125df9874fa9703
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6355
Tested-by: jenkins
For the remaining NULL comparisons, remove then manually.
While there, make more readable a loop, by moving the assigment
out of the loop condition.
Change-Id: I44193aaa95813156a3a79c16b80e1ad333dc1eaf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6353
Tested-by: jenkins
Patch generated automatically through a modified checkpatch that
detects the patterns
if (NULL == symbol)
if (NULL != symbol)
and through flags "--types COMPARISON_TO_NULL --fix-inplace".
The unmodified checkpatch detects this pattern as Yoda condition,
but it's odd fixing it as Yoda condition and then again as NULL
comparison. This triggered the modification to the script.
Change-Id: I5fe984a85e9c4fc799f049211797aef891ebce18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6352
Tested-by: jenkins
Patch generated automatically through the new checkpatch with
flags "--types COMPARISON_TO_NULL --fix-inplace".
This only fixes the comparisons
if (symbol == NULL)
if (symbol != NULL)
The case of NULL on the left side of the comparison is not tested.
Some automatic fix is incorrect and has been massaged by hands:
- if (*psig == NULL)
+ if (*!psig)
changed as
+ if (!*psig)
Change-Id: If4a1e2b4e547e223532e8e3d9da89bf9cb382ce6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6351
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: I7cc87458a341bae29a4f772b0af5d97b4bfc2da3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6343
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Fix the remaining Yoda conditions, detected by checkpatch but not
fixed automatically.
While there, apply minor style changes.
Change-Id: I6e1978b89c4d56a20aceaeb2b52968eb6384432a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6356
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
There are ~900 Yoda conditions to be aligned to the coding style.
For recurrent Yoda conditions it's preferable using a trivial
script in order to minimize the review effort.
E.g. comparison of uppercase macro/enum with lowercase variable:
- ...(ERROR_OK == retval)...
+ ...(retval == ERROR_OK)...
Patch generated automatically with the command:
sed -i \
's/(\([A-Z][A-Z0-9_]*\) \([=!]=\) \([a-z][a-z0-9_]*\))/(\3 \2 \1)/g' \
$(find src/ -type f)
While there, remove the braces {} around a single statement block
to prevent warning from checkpatch.
Change-Id: If585b0a4b4578879c87b2dd74d9e0025e275ec6b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6354
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Convert to lowercase the name of arrays.
Convert to macro two uppercase const variables.
Change-Id: Ic6f5cad38722dfdf78d662ff4893e94482ab423d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6348
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Xiang W <wxjstz@126.com>
Uppercase symbols are normally used for macro or enum's values.
Convert the uppercase const variables to macros.
Change-Id: I749544c2e5deba65583824a7c2a6023e697714df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6346
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Uppercase symbols are normally used for macro or enum's values.
Convert the uppercase const variables to macros.
Change-Id: I4ba47ce2d3183b50730c5a9a265f274c7b802519
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6345
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Xiang W <wxjstz@126.com>
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: Iec58f7fe1d65f621ae0c841b5e25ef222885792b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6341
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Xiang W <wxjstz@126.com>
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: I1325560ef0350517d86d4927cb17ceaae81b75d2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6340
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: I3f0879f0f33c6badc36a0dc60229323978a7e280
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6338
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
Use a command group 'ftdi' with subcommands instead of individual
commands with 'ftdi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I93a0ae7070226cd2fdea566effeb14a141269de8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6332
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Added support for reading and writing 64-bit data items
using TCL commands "mem2array" and "array2mem". Until now,
data items only up to 32 bits were supportd.
- Cleaned up functions target_array2mem() and
target_mem2array(), especially data types of variables
and variable declarations (scope).
Change-Id: Ia0ba427804f8fd8d7568f12714ab36984d6d5e24
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6286
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add 64-bit address support to the target mem2array and array2mem commands
Change-Id: Ibdcc076ca5581f4fd87e92318aab33907e22d6ce
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/6246
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This change fixes behavior of the SEMIHOSTING_SYS_CLOSE operation.
It ensures that OpenOCD's own stdin/stdout/stderr streams are never
closed, not even if the target requests it via semihosting.
Change-Id: Ia85af5963d1a3516284fd834f7197369a8fb268c
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6291
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Capture the value of "errno" in semihosting isatty() call,
as is done in other syscalls.
Change-Id: I41b72175635f06c000536f583e3efa30fb57379e
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6292
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Drive the output enable for TMS and TDI
Change-Id: Ib23afd2f5149d4ce402d88781e68dcf0f074f395
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/4179
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The legacy ft2232 driver suggests that the adapter has tristate
buffers on both nSRST and nTRST, even though they were not used as
such.
Change-Id: I971692ea6b3439ac93311b89877825a5cc21df46
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3663
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Flyswatter URL is dead and requires us to use web.archive.org since
the product is discontinued. The Flyswatter 2 is still active and
accessible at a different URL.
Change-Id: Ib2d9de70a9728b0f0ef73f5e479bca81f958442c
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/6337
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If not implemented, these specify to regular target read/write. However,
if individual threads in an RTOS can have different address translation
configured then the RTOS support can use this to do the right thing.
Use this in hwthread, where of course address translation can be set up
differently for different real cores.
Change-Id: I62c501cff1f863d855ee197dee7b73204ea8885a
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/6327
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- In "reg" TCL command handler, the return value of register get()
and set() callbacks must be checked, in the same manner as it is
done in e.g. gdb_set_register_packet() or gdb_get_register_packet().
- Minor cleanup of variable definitions in the "reg" command
handler.
Change-Id: I8c57e7c087fe31d1abffa3c4d1f79a01af4c9c97
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6293
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provides ARM LPAE support to allow 64-bit TAR setting
on MEM AP accesses.
Tested on a 4-core ARM ARES Processor system using an
AXI Access Port.
Change-Id: I88f7a0a57a6abb58665032929194a41dd8729f6b
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5576
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Convert CamelCase enum in uppercase and the other symbols in
lowercase.
Change-Id: I141c55bdfe6ef2a2da28d1da15a283a644ae7cb2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6306
Tested-by: jenkins
Only one exported symbol from eCos is included in this patch.
The eCos code is left untouched to prevent conflicts with patches
currently under review.
While there, remove an unused camelcase macro
Change-Id: I8d22dec6e243c00665d99a8b8ba00474b4f088db
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6305
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The eCos code is not part of this patch to prevent conflicts with
patches currently under review.
Change-Id: I71369165f2eef419b83a79ffcff50287f77949c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6304
Tested-by: jenkins
No cross dependency, just changes internal to each file/function.
Change-Id: I04153a5720b0540bc1998bafe526d523b2ee5515
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6303
Tested-by: jenkins
Jian-Hong Pan
Tim Newsome
PoroCYon
Matthew Mets
Antonio Borneo
Paul Fertser
Florian Fainelli
Marc Schink
Jan Matyas
Daniel Goehring
Patrick Stewart
Andreas Fritiofson
Kevin Burke