No need to indirect from registered integers to pointers.
Just stash the pointers directly in the register struct,
and don't even bother registering.
This is a small code shrink, speeds register access just
a smidgeon, and gets rid of another rude exit() path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
And move the rest of the vector_catch stuff into the C file;
it's not part of the module interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Also, switch integrity check over to the correct magic number,
and remove duplicate v4/v5 #define.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Have ARM11 register the "standard" ARM commands. For now, only
disassembly really works.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename the "armv4_5" command prefix to straight "arm" so it makes
more sense for newer cores. Add a simple compatibility script.
Make sure all the commands give the same "not an ARM" diagnostic
message (and fail properly) when called against non-ARM targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use size_t instead of uint32_t when specifying file sizes. Update all
consumers up through the layers to use size_t when required. These
changes should be safe, but the higher-levels will need to be updated
further to receive the intended benefits (i.e. large file support).
Add error checking for fileio_read and file_write. Previously, all
errors were being silently ignored, so this change might cause some
problems for some people in some cases. However, it gives us the chance
to handle any errors that do occur at higher-levels, rather than burying
our heads in the sand.
Tweak "standard" ARM disassembler diagnostics to fail if the target
is not "an ARM" (vs. not "an ARMV4/5"), so it makes more sense for
cores inheriting this as the "generic" disassembler.
Also, to use the Thumb2 entry instead of the original Thumb entry.
This makes it work better for both newer cores (which support those
added instructions) and for BL and BLX instructions on older cores.
(Those instructions are 32-bits, which requires curious state-aware
code to go through a 16-bit decode interface...)
Plus minor cleanups, notably to have fewer exit paths and to make
sure they all return failure codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
They're really too big to inline, at least for code that's
not in any performance-critical loops.
Also move the associated string table to the rodata section.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't include it in more headers than necessary; just
use it in the few files that actually need it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The ARRAY_SIZE macro was defined in several target files, so move it
to types.h.
This patch also removes two other identical macros: DIM (from jtag.h)
and asizeof (from arm11.h).
Eliminate redundant check that gets covered by using unsigned type.
Created to eliminate noise from subsequent patches, but this kind of
conversion will be beneficial in similar ways throughout the tree.
The container_of macro is useful as a general solution. It belongs
in types.h, rather than target.h where it was introduced. Requires
the offsetof macro, which comes from <stddef.h> (moved as well).
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Lots of files still include it, often through needless
duplicate inclusion of "log.h"; sigh.
This cleans up the inclusion graph a bunch, so there are
fewer inclusion paths, but it doesn't change much otherwise.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
downloadable algorithms actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also: "algorithm.h" doesn't need to include "types.h" again;
it already comes from a different header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Now the ARM11 cores can use the renamed arm_checksum_memory()
and arm_blank_check_memory() routines ... do so.
Sanity checked with "flash erase_check" of both NOR banks on an
OMAP2420 ... the algorithm code dumped four lines of of "poll"
status after each of almost 520 blocks (yes, *very* annoying) but
gave plausible results after producing that spam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Three changes: remove ARM11_HANDLER() in favor of normal structure
initialization syntax; fix goofy indentation in that structure; and
don't needlessly export arm11_register_commands(), it's only called
through that method table.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The arm7_9_checksum_memory() and arm7_9_blank_check_memory()
routines are not actually specific to the ARM7 and ARM9 core
generations ... they can work for any core which can run
algorithms using basic ARM (not Thumb) instructions.
Rename them; move the declarations to a more generic site;
likewise move the code (and tidy it a bit in the process).
NOTE: the blank_check() method falsely returned a success
status (0) on one error path, when the algorithm failed.
Fixed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously this flag was stored in "target_type", so that for example
if there were two ARM7TDMI targets in a scan chain, both would claim
to have been examined although only the first one actually had its
examine() method called.
Move this state to where it should have been in the first place, and
hide a method that didn't need exposure ... the flag is write-once.
Provide some doxygen. The examine() method is confusing, since it
isn't separating one-time setup from the after-each-reset stuff. And
the ARM7/ARM9 version is, somewhat undesirably, not leaving the debug
state alone after reset ... probably more of an issue for trace setup
than for watchpoints and breakpoints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Removes unused arm_jtag_buf_* helpers from arm_jtag.[ch]. These could
reappear if patches are provided to conver the tree to use them, but
this code should not be in the master tree until that series is ready.
This fixes an issue due to the new command handler syntax caused by the mw handler playing with the args pointer before
using the CMD_NAME macro. Fix is to move this call above the lines changing args.
Changed some printf format strings..
[dbrownell@users.sourceforge.net: shrink lines, fix indents]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Kick in ETM (and ETB) support for ARM11. Tested on OMAP 2420,
so update that configuration. (That's an ARM1136ejs, ETB,
OpenGL ES1.1, C55x DSP, etc.)
Also update the other ARM11 ETM + ETB targets in the tree
to set up these modules. (Not tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
These aren't desirable, given "standard" ETM support.
Also remove the now-unused arm11_find_target().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
No point in having two identical examine methods for the
ARM7TDMI and ARM9TDMI drivers; move, rename, shrink, share.
Add a bit of doxygen; stop needlessly exporting a method.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Return NULL from etm_build_reg_cache() not ERROR_OK; and share
code on that fault path.
Let ETM code handle any tracking of its cache -- not callers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This will enable reusing many common ARM utilities, in
particular the ETM and ETB support. The ARM11 support
can still be much simplified after this patch, though.
Note: none of those common utilities kick in yet...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We have too many different registers, and too many version and
context dependent interpretations, for this type of bitfield
management to be scalable.
(Anyone who really wants bitfield interpretation *can* do that
in Tcl code...)
There are ... quite a few copies of the same ARM dummy registers.
There should eventually be one copy; this many is craziness.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove the last external user of arm7_9_get_arch_pointers(), and
that annoying downcast utility. Add an is_arm7_9() predicate.
Stop returning specious success codes on various failure paths
in the ARM7/ARM9 commands which used that downcast utility.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell
Zachary T Welch
Krzysztof Dziuba
Dean Glazeski
Ferdinand Postema