Change-Id: I693e5b7933fc61956010a96be57ee6eb8abd3c31
Signed-off-by: Anton V. Kirilchik <kosmonaffft@gmail.com>
Reviewed-on: http://openocd.zylin.com/5422
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Both Gen2 and Gen3 used the same init_reset{} implementation,
pull it into common file and include it from both generations.
Moreover, this behavior is SoC specific, not board specific,
so move the common init_reset into target/ directory.
Change-Id: I5489a4bff9a786da8cb7fd7a515b0c9ce9dc16e3
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5400
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Adopted only fast algorithm for flash programming:
- write_word and write_byte methods have been removed.
- start and end write alignments have been defined.
Moved flash controller registers offsets in a common file
shared with the flash algorithm.
- the flash base address is passed to the flash algorithm
as a parameter.
Removed unused functions
Change-Id: I80aeab3994e477044bbcf02e66d9525dae0cb491
Signed-off-by: luca vinci <luca.vinci@st.com>
Reviewed-on: http://openocd.zylin.com/5393
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Michele Sardo <msmttchr@gmail.com>
Drop old Renesas Gen2 SoC configurations, as they were superseded by
the new unified config.
Change-Id: I7c2ccbdc13b01a552ce9cafdc1538f226beaa9f2
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5399
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add configuration for the Renesas R-Car Generation 2 targets.
These are SoCs with Cortex A15s and A7s. All cores currently
supported by OpenOCD are supported here as well as two new
cores, M2N and V2H, for the sake of support completeness.
Change-Id: Ib6fe70a91360b4f8bd69822ee28b6dea530cfa0a
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5397
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Some text file is missing newline at EOF.
Add it.
Change-Id: Ieebc790096f40961283c644642e56fde975e957f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5167
Tested-by: jenkins
Change-Id: Ib452435b13c3cb8d14453d983151936238b9601d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5419
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Avoid annoying "deprecated" messages in the scripts
distributed with OpenOCD code.
Change-Id: I82d27cd420db30f0653efbd286a627ef56a8c1fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5287
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Currently the code assumes the adapter uses raw SWD, and the expected ID
code of the CPU is even wrong. An adapter speed is also not specified.
All these prevents the config file to be used with ST-Link.
Fix the config file, to allow it to be used with ST-Link.
Change-Id: I1244320fabfe8ee23da5a56a592dbeddc72cc8d5
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-on: http://openocd.zylin.com/5297
Tested-by: jenkins
Reviewed-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STM32H7x7 and STM32H7x5 devices contains two cores : CM7 + CM4
The second core creation is only done when
* DUAL_CORE variable is set to true
* non HLA interface is used
A second check for the second core existence is done in cpu1 examine-end
Once the second core is detected it gets examined.
Furthermore, the script provides a configurable CTI usage in order to halt
the cores simultaneously.
Tested on Rev X and V devices.
PS: the indentation was a mix of spaces and tabs, all changed to tabs.
Change-Id: Iad9c30826965ddb9be5dee628bc2e63f953bbcb8
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The STM32H7 has three access ports. The DBGMCU component is available
through AP0 at 0x5C001000 and through AP2 at 0xE00E1000. Using the
latter is preferable for early configuration because it works in all
power states and while SRST is asserted, whereas the former does not.
Change-Id: Iaf8f01d769efb6655040060a8e1e951e1f7e50ab
Signed-off-by: Christopher Head <chead@zaber.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/4742
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
SWM050 is a series of MCU product by Foshan Synwit Tech, which is
available in TSSOP-8 or SSOP-16 packages.
Adds flash driver for the internal 8KiB flash of the MCU. The registers
are based on reverse engineering the J-Flash blob provided by the
vendor.
Also adds a pre-made cfg file.
Change-Id: I0b29f0c0d062883542ee743e0750a4c6b6609ebd
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Caleb Szalacinski <contact@skiboy.net>
Reviewed-on: http://openocd.zylin.com/4927
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is not flash bank support at the moment.
Change-Id: I833c009d9d21cdeb70b57d67eb557d50ed0fb4de
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5205
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also
adds configuration file for SSE-200 based Musca A board. Flash programming
support for Musca A QSPI flash is still not functional. This configuration
will be updated once that support lands into OpenOCD.
Please refer to ARM documentation for more information about SSE-200 and
Musca A.
Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/5006
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The V3M SoC is R8A77970 while the V3H SoC is R8A77980 . Update the
CHIPNAME and swap the SoCs to keep the list sorted.
Change-Id: I7e1777c0c7181e5e0beac98333f2047cb443d0df
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5140
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas RZ/A1H target.
This is an SoC with one Cortex A9 ARMv7a core and
up to 10 MiB of on-SoC SRAM.
Change-Id: I20fd54b385fe1ba1cc325451c3fdfa3a835d4884
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The commands prefixed with "ocd_" are removed.
Remove them from configuration files.
Change-Id: Ib44627ee17a39f3d06b479507ab5a025073bf9a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5090
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
* Add mem_ap for direct access to axi bus (without halting cpu)
* Mark m4 core with -defer-examine because it's not used by default
* Make a53.0 default target since it's the boot core
Change-Id: Id031533c5d4af346eb08a9ac2532fa1bca602913
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5036
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 the 6UL 6ULL 6ULZ chips are based on Cortex-A7
which is at a different address so a custom script is required.
Tested on imx6ull-14x14-evk
Change-Id: I72822d2241045c318389fadbc66d7aaabaaf4cb5
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5040
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike the rest of imx6 a Cortex-M4 was added with a second CoreSight
DAP so a separate script is required.
Tested on imx6sx-sdb running linux
Change-Id: I1561910b233015f42508f341175822c0827655ec
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5041
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Unlike imx7d/solo supported by imx7.cfg the M4 core is on a different AP
and is always running by default so no -defer-examine is required.
There is also only one Cortex-A7
Tested on imx7ulp-evk
Change-Id: Ifa923d1b9a372c788e6654bc2233fd4d9073a32d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5043
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Copy all SJC TAPIPs from imx6 reference manuals.
Some imx6 chips are based on Cortex-A7 or have an additional Cortex-M4
and need separate scripts.
Change-Id: I3b07d94058c2c5e6313cfc8bb43134a90682a62e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5034
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
OpenOCD scripts are usually indented with 4 spaces but here there are 8.
Change-Id: Iaad53e3b377d246d99119bb7bb5fd75d4422f564
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5039
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Looking through imx6 manuals all of them claim that "In follow-on
silicon revisions the ID value is subject to change by incrementing the
first nibble".
Handle this by passing -ignore-version to jtag newtap command.
Change-Id: I7fc4779f9757d527ea20a5174a8c90f919580013
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This allows bus access even when CPU is off.
Change-Id: I2d5c5581cd0169aecb92ac7b610810988a8dcef4
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5032
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This patch remaps the Flash over ITCM region as virtual to ensure that
any breakpoint placed in this area will be automatically set as an
hardware breakpoint. This patch is a fix to a regression introduced with
changes #4429.
Change-Id: I03d46d8537ef06b33a3d4a2328274667c6481969
Signed-off-by: Rocco Marco Guglielmi <roccomarco.guglielmi@gmail.com>
Reviewed-on: http://openocd.zylin.com/5097
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The imx8m also has a Cortex m4 so add a target for it.
Change-Id: I2abf62b6232c547fe9b12507f459835b11c63a6d
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-on: http://openocd.zylin.com/4501
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The OTP is part of the flash memory. It has 512 (1024 for F7) bytes
and is organized in 16 sectors with 32 (64 for F7) bytes each.
The OTP is exposed as separate flash bank 1 and can be used
with the usual flash commands.
Writing the OTP can be done as follows:
> stm32f2x otp 1 enable
> flash write bank 1 foo.bin 0
> mdw 0x1fff7800 4
> verify_image foo.bin 0x1fff7800
> stm32f2x otp 1 disable
Note: This patch is largely a rebase/cleanup of a patch
from 2012 by Laurent Charpentier and he did most of the work.
No new Clang-Analyzer warnings.
Change-Id: I5e6371f6a7c7a9929c1d7907d6ba4724f9d20d97
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/829
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The new Microchip (former Atmel) series powered by Cortex-M4 looks
very similar to older M0+ powered SAM D2x at the first sight.
Unfortunately the new series differs a lot in important details.
NVMCTRL has different register addresses, moved important bits
and even changed binary command set. An universal driver for all SAM D/E
would be very complicated. That's why a new driver was derived.
Tested on Microchip SAM E54 Xplained Pro kit (board cfg included).
Adjusted for the restructured dap support.
Checked by valgrind and clang static analyzer.
Change-Id: I26c67047a552076f4b207b9b89285a53d69b4ca4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4272
Tested-by: jenkins
Reviewed-by: Andres Vahter <andres.vahter@gmail.com>
The original script was broken by changes to the Cortex-A code. The
recent introduction of the mem_ap target provided a new mechanism to
allow the script to be fixed. This also adds an example board script
for the ADSP-SC584-EZBRD.
Change-Id: I36bc1ac6b6c036539f4175f1e65223ba10a35355
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/4855
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The xilinx_ultrascale.cfg target is actually the configuration for a
ZynqMP, which is a combination of an UltraScale+ FPGA core and a quad
core A53. Update the filename/comments to reflect this, and include
the tap IDs for all known FPGA cores for this part.
Change-Id: I70dfcc99861a482b83b6a795e83021d9cf1fe047
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4850
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Agama family of devices (CC26x2/CC13x2) required an
additional bit to be set when adding the core's TAP into
the scan chain. The cancel reset bit 0x10000 tells the
ICEPick to take the bus out of reset so that the other
bits will take effect. This bit is a NOP on other devices
and ICEPicks, so the change shouldn't adversely affect
other devices.
Change-Id: I9245eef0936ea7eea28ae84ab5e8ce05fa63af40
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4789
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These devices differ from LPC8xx devices in that they have a different
IAP entry point, but everything else is the same. Using Tcl to pass
different IAP entry point.
no new Clang analyser warnings and no new build sanitizers issues.
Change-Id: I2d654dd250f416e74262c0228cad8713a283402f
Signed-off-by: Rod Boyce <developer@teamboyce.co.uk>
Reviewed-on: http://openocd.zylin.com/4684
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Since commit bae76053dc
gdb-attach event is defined as halt by default.
Remove useless and in case of bcm281xx wrong definitions of the event.
Change-Id: I8e69780a93722eb9392673303f54d502e71eceb6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4763
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
The reset_config line in the config file does not actually set
connect_assert_srst (the default is connect_deassert_srst), but it reads
as if it does. Clarify that the target is compatible with
connect_assert_srst, without suggesting that the file actually sets it
to that value.
Change-Id: I14e9445ab282d386b5d0055f6adf03d7c8878a8c
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4743
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The stm32h7x.cfg does not specify connect_assert_srst or
connect_deassert_srst in its reset_config. The comment claims that it
will therefore connect in reset. However, per the manual, the default
configuration is actually connect_deassert_srst, not
connect_assert_srst. In actual fact, connect_assert_srst does not work
on the STM32H7 because, while SRST is asserted, everything on the AXI
bus is inaccessible. The CPU core is accessible, but since the
examine-end event handler also pokes at the DBGMCU peripheral, that will
fail in connect_assert_srst mode. So using connect_deassert_srst is
appropriate, so fix the comment accordingly.
Change-Id: If3e32e871fb19cc61183bdf911b7c5efd80b62e2
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4741
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When using stlink for CM7 targets we have to rely on its firmware
to do the right thing as direct DAP access is not possible.
Change-Id: Ieee69f4eeea5c911f89f060f31ce86ed043bdfd0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4732
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This allows for programming the PL part of the Xilinx Zynq 7000
Change-Id: I89e86c0f381951091f6948c46802d17d7f1f3500
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-on: http://openocd.zylin.com/4177
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
eSi-RISC is a highly configurable microprocessor architecture for
embedded systems provided by EnSilica. This patch adds support for
32-bit targets and also includes an internal flash driver and
uC/OS-III RTOS support. This is a non-traditional target and required
a number of additional changes to support non-linear register numbers
and the 'p' packet in RTOS support for proper integration into
EnSilica's GDB port.
Change-Id: I59d5c40b3bb2ace1b1a01b2538bfab211adf113f
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4660
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car Generation 3 targets.
These are SoCs with Cortex A57s, A53s, and R7s. All cores
are supported.
Change-Id: I795233210e4f647a1a2a0adea7c058ae98b5db70
Signed-off-by: Adam Bass <adam.bass@renesas.com>
Reviewed-on: http://openocd.zylin.com/4669
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Change-Id: Ic00d3192642c682f370a6f7f8b70ae29744eb746
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4678
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I7c5c9720ded329848647f17db95f845e46c01c19
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4674
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Adding flash programming support for Maxim Integrated MAX32XXX
devices.
Change-Id: I5b0f57a885f9d813240e4bc2d9f765b743e1cfc3
Signed-off-by: Kevin Gillespie <kgills@gmail.com>
Reviewed-on: http://openocd.zylin.com/3543
Tested-by: jenkins
Reviewed-by: Ismail H. KOSE <ihkose@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Sync it with experience gathered on Qualcomm QCA4531 SoC. This
chips are in many ways similar.
Change-Id: I06b9c85e5985a09a9be3cb6cc0ce3b37695d2e54
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4423
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
this helper works on many different boards, so it is
good to have it in target config
Change-Id: I068deac36fdd73dbbcedffc87865cc5b9d992c1d
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4422
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The ar9331_25mhz_pll_init and ar9331_ddr1_init routines
can be used not only for TP-Link MR3020 board,
so move them to the common atheros_ar9331.cfg file.
Change-Id: I04090856b08151d6bb0f5ef9cc654efae1c81835
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2999
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable
Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Change-Id: I58398c00943b005cfaf0ac1eaad92d1fa4e2cba7
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4405
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Added msp432 flash driver to support the TI MSP432P4x and
MSP432E4x microcontrollers. Implemented the flash algo
helper as used in the TI debug and flash tools. This
implemention supports the MSP432E4, Falcon, and Falcon 2M
variants. The flash driver automatically detects the
connected variant and configures itself appropriately.
Added command to mass erase device for consistency with
TI tools and added command to unlock the protected BSL
region.
Tested using MSP432E401Y, MSP432P401R, and MSP432P4111
LaunchPads.
Tested with embedded XDS110 debug probe in CMSIS-DAP
mode and with external SEGGER J-Link probe.
Removed ti_msp432p4xx.cfg file made obsolete by this
patch.
Change-Id: I3b29d39ccc492524ef2c4a1733f7f9942c2684c0
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4153
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ica0025ea465910dd664ab546b66f4f25b271f1f5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4570
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
As seen on the FRDM-LS1012A board.
Change-Id: Ifc9074b3f7535167b9ded5f544501ec2879f5db7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/4594
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7794 E2 target.
This is an SoC with two Cortex A7 ARMv7a cores, both A7
cores are supported.
Change-Id: Ic1c81840e3bfcef8ee1de5acedffae5c83612a5e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4531
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
STM32F7xx devices need faster clock for flash programming
over JTAG transport. Using reset default 16 MHz clock
resulted in lot of DAP WAITs and substantial decrease
of flashing performance.
Adapted to the restructured dap support
(see 2231da8ec4).
Change-Id: Ida6915331dd924c9c0d08822fd94c04ad408cdc5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4464
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Added cc26xx flash driver to support the TI CC26xx and CC13xx
microcontrollers. Driver is capable of determining which MCU
is connected and configures itself accordingly. Added config
files for four specific variants: CC26x0, CC13x0, CC26x2, and
CC13x2.
Note that the flash loader code is based on the sources used
to support flash in Code Composer Studio and Uniflash from TI.
Removed cc26xx.cfg file made obsolete by this patch.
Change-Id: Ie2b0f74f8af7517a9184704b839677d1c9787862
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4358
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Erasing is not supported by the hardware, it can be written directly.
Tested on CY8CKIT-059, except modifying-write.
Change-Id: I6e920ed930dcd5c7f0b10c5b1b4791a828d9080a
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3434
Tested-by: jenkins
Always probe for ECC mode and display ECC sectors if disabled.
Non-ECC write is implemented as zeroing the ECC/config bytes.
Erasing ECC sectors is ignored, erase-checking takes them into account.
Tested with CY8CKIT-059 (CY8C5888), except ECC mode.
Change-Id: If63b9ffca7ad8de038be3c086c49712b629ec554
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3432
Tested-by: jenkins
Added cc3220sf flash driver to support the TI CC3220SF
microcontrollers. Implemented flash driver to support the
internal flash of the CC3220SF. The implementation does not
support the serial flash of the CC32xx family that requires
connection over UART, and not via JTAG/SWD debug. Added config
files for both CC32xx devices (no flash) and CC3220SF (with
flash).
Updated to implement comments from code review.
Additional updates to handle remaining comments from review.
Additional updates per review.
Added code to only request aligned writes and full 32-bit
words down to flash helper algorithm. Updated for recent
changes in OpenOCD flash code.
Removed cc32xx.cfg file made obsolete by this patch.
Change-Id: I58fc1478d07238d39c7ef02339f1097a91668c47
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4319
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The "Blue Pill" is a popular development board with an STM32F103C8
micro controller. According to sources, it has a 128kB Flash on board
even though the option bytes only report 64kB. This patch therefore also
modifies target/stm32f1x.cfg to take an optional FLASH_SIZE variable into
account which the board file sets to 0x20000.
Change-Id: I8a78ccd2b5faf637c539ee3cf8136789ee15c95d
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4495
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add configuration for the Renesas R-Car R8A7790 H2 target.
This is an SoC with four Cortex A15 and four Cortex A7
ARMv7a cores, only the four A15 cores are supported.
Change-Id: I6099b257cc0f04e6858ed5f5f8c8d8ad82ef7650
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4490
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Vybrid VF6xx SoCs contain an additional Cortex-M4
core connected to AP number 3 of the main DAP.
Change-Id: I59c020fdfc53e909b1f0dac1a8627a62cdaa74f2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3640
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
includes target configuration for i.MX8M SoC family,
board file needs to set up CHIPNAME and CHIPCORES
to match the actual hardware configuration
Change-Id: Ieb6d89cab2477a58f85d0ef9cd242710950191c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4434
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Add configuration for the Renesas R-Car R8A7791 M2W target.
This is an SoC with two Cortex A15 ARMv7a cores, both cores
are supported.
This patch is based on initial submission by Adam Bass and
improvements by Niklas Söderlund.
Change-Id: I297da62b9ce71ad222a401d98e6bcb8502427673
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Adam Bass <adam.bass@renesas.com>
Cc: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-on: http://openocd.zylin.com/4485
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Make sure the user is aware he can lock the device though unlock is not
possible without access to MDM-AP.
Change-Id: I92676530e95d19489c6739748a99c2895849f90f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4403
Tested-by: jenkins
This makes it possible to program newer EFM32 and EFR32 chips with
JTAG, as opposed to SWD.
Change-Id: Ia3e8c1bbc66fc1f33e8cf2087ccf0d1b4dfd74e1
Signed-off-by: Jonas Norling <jonas.norling@cyanconnode.com>
Reviewed-on: http://openocd.zylin.com/4262
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik@hederstierna.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The ICEPick-D jtag router has core control registers
that provide the same (or similar) functionality as
the tap control register, for individual cores
accessible through the same tap (e.g. through a DAP).
Core control registers are located at address "0x60 +
core-id" of the ROUTER address space (IR=ROUTER).
It is sometimes helpful or even necessary to modify the
core control register. This patch renames the
"icepick_d_coreid" function to the more appropriate
"icepick_d_core_control" and adds a "value" argument
that allows writing of arbitrary value.
"icepick_d_tapenable" is extended by an optional value
argument so that core control can be written as the tap
is enabled.
Change-Id: I0e7f91b596cb5075364c6c233348508f58e0a901
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4141
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Flash ROM API command PSOC4_CMD_SET_IMO48 is now optional on new devices.
Also code tidy up:
- improved system ROM call error detection
- probe does not require the target to be halted
- default_padded_value and erased_value set to 0
- fixed endianess problem in flash write and protection setting
- removed fancy chip detection table as it would be updated too often
- psoc4 flash_autoerase is now on by default to ease programming
psoc4.cfg distinguishes chip family and uses either proprietary acquire
function of a KitProg adapter or TEST_MODE workaround to "reset halt"
Change-Id: I2c75ec46ed0a95e09274fad70b62d6eed7b9ecdf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3807
Tested-by: jenkins
Reviewed-by: David Girault <david.f.girault@gmail.com>
Some parts have only that much. Reported by robertfoos_ on IRC.
Change-Id: I684fdccfa62cf726466ddc467543a990fd88c4dc
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4369
Reviewed-by: Robert Foss <robert.foss@memcpy.io>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
New low-end chips have only 2k of RAM, workarea size adjusted
Change-Id: Ibfccd73fef9e6dabffc87d901736c5626ce411fe
Signed-off-by: Ilia Motornyi <elijah.mot@gmail.com>
Reviewed-on: http://openocd.zylin.com/4308
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
New STM8 target based mostly on mips4k. Target communication
through STLINK/SWIM. No flash driver yet but it is still possible
to program flash through load_image command. The usual target debug
methods are implemented.
Change-Id: I7216f231d3ac7c70cae20f1cd8463c2ed864a329
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/3953
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This config covers the 4x Cortex A53 CPUs. A custom connector
is required from J14 to standard ARM JTAG on v1 boards. However
v2 hardware should have a standard FTSH-105-01-L-DV connector.
Pinmuxing code to enable JTAG pins is included in l-loader-poplar
repository, so board is flashed with open source code, JTAG
is available at very early boot. Alternatively the following
pokes can be issued from U-Boot to enable JTAG (e.g. to debug
hisilicon SDK).
mw 0xf8a210ec 0x130;
mw 0xf8a210f0 0x130;
mw 0xf8a210f4 0x130;
mw 0xf8a210f8 0x130;
mw 0xf8a210fc 0x130;
mw 0xf8a21100 0x130;
Change-Id: I2b83dfcb3dc5461c1620f94dd99aa7b31fdda59b
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-on: http://openocd.zylin.com/4161
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
in some cases we need something to test if uart is actually
properly connected.
Change-Id: I5a16b053164b34bb30ae8370753be12887a85c51
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/4194
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Anton V. Kirilchik
Marek Vasut
luca vinci
Antonio Borneo
Marc Schink
Tarek BOCHKATI
Icenowy Zheng
Christopher Head
Andreas Färber
Felipe Balbi
Al Dyrius
Caleb Szalacinski
Marc Schink
Omair Javaid
Leonard Crestez
Rocco Marco Guglielmi
Angus Ainslie
Moritz Fischer
Tomas Vanek
Peter Lawrence
Jonathan McDowell
Edward Fewell
Rod Boyce
Jean-Christian de Rivaz
Paul Fertser
Steven Stallion
Adam Bass
Kevin Gillespie
Oleksij Rempel
Dominik Peklo
Oleksij Rempel
Antony Pavlov
Bohdan Tymkiv
Matthias Welwarsky
Niklas Söderlund
Michele Sardo
Jonas Norling
Ake Rehnman
Jiri Kastner
elmot
Alexandre Torgue
Peter Griffin
Slowcoder