With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
To improve readability and to push more uniform code style.
Prefer 'if (false) {...}' for unused code so it get checked by the
compiler.
Define preferred indentation for 'switch' statement.
Require balanced brackets in 'if/else'.
Report the max line length.
Report the formatting strings for stdint/inttypes types.
Report the type 'target_addr_t'.
Prefer 'unsigned int' to 'unsigned'.
Change-Id: I0192a4ed298f6c6c432764fdd156cffd4b13fc89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6203
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Nowadays, when it's difficult to buy STM32F030,
the use of GD32F130 seems to be an interesting functional alternative.
This is cortex-M3 and it works with the stm32f1x driver, but unfortunately not fully.
The main difference is another offset of user option bits
(like WDG_SW, nRST_STOP, nRST_STDBY) in option byte register
(FLASH_OBR/FMC_OBSTAT 0x4002201C).
Any use of functions like lock or unlock results in change default values of the those bits stored in flash.
Thus broken microcontroller is malfunctioning, e.g. flash block programming is interrupted
by unexpected active hardware watchog (after 0.4s).
This patch is a simplified version of #4592 done by Dominik Peklo (http://openocd.zylin.com/#/c/4592/).
GigaDevice GD32F1x0 & GD32F3x0 series devices share DEV_ID
with STM32F101/2/3 medium-density line,
however they use a REV_ID different from any STM32 device,
so can be succesfully detected.
Change-Id: I252cdf738d94983b70676a3497326f90c329e292
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Reviewed-on: http://openocd.zylin.com/6164
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 7a731eb637 ("Added HostOS variable"), merged in 2009,
adds a TCL global variable 'ocd_HostOS' that reports in a string
the OS of the host.
This was proposed as a workaround for jimtcl that didn't define
the standard TCL variable 'tcl_platform(os)'.
With commit 42f3fb7b7f46 ("Determine platform_tcl() settings with
configure"), merged in 2010 and part of jimtcl 0.70 issued in
early 2011, jimtcl provides the requires TCL standard variable
'tcl_platform(os)'.
The variable 'ocd_HostOS' has never been used by any TCL script
distributed with OpenOCD.
Drop the TCL variable 'ocd_HostOS'.
Change-Id: I27858de35cc9d30df97145ca1ccd24877be4af11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6189
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix the warning below by adding a '.' after xref in line 10184:
./doc/openocd.texi:10184: warning: `.' or `,' must follow @xref, not c
Change-Id: Ibd976ae61cf6845e925b839321444dcb25a3c04a
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6179
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix the warning below by adding a '.' after xref in line 4517:
../code/doc/openocd.texi:4517: warning: `.' or `,' must follow @xref, not )
Change-Id: I6e529c7e83c9f912e1dd899abf5f630c90b583d9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6174
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The mode of command 'ftdi_layout_signal' is set to COMMAND_ANY in
[1] and the command has no constraints that limits its use to the
config phase only.
But [2] documents it as '{Config Command}'.
Update the documentation to report the correct mode '{Command}'.
[1] commit f5e97b5e1b ("Add FTDI JTAG driver using MPSSE layer")
[2] commit 76afadeb7b ("doc: Add documentation for the ftdi driver")
Change-Id: I6b14aebb98e48f7080c585f3df881714bb188af0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6155
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The command 'ftdi_location' is deprecated and a TCL procedure is
in place to direct the user to the replacement command.
There is no need to document the deprecated command.
Remove 'ftdi_location' from the documentation.
Change-Id: Ia431c6b0e7444d3f3288c088429bfb47089ff1b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6154
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Some command that is only valid during configuration is documented
as generic command.
Annotate them as {Config Command} in the documentation.
Change-Id: Ifdbb6ec89b945e3d7adce94af379d94f511a64b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6153
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I41a8447d487ec8f6f32c2babcbc73ac21c769344
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6152
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every Command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I797e8d9f5ab0aa1936f350b340d3bdd52373f5aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6151
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Both 'Command' and '{Command}' are in use, with the following
statistics:
0 @deffnx {Command}
45 @deffn {Command}
31 @deffnx Command
382 @deffn Command
While 'Command' is the most popular, prefer the version within
curly-brackets that has to be used for multi-word definition like
'{NAND Driver}', '{Config Command}', '{FPGA Driver}', ...
Patch generated through:
sed -i 's/^\(@deffn \)\(Command\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx \)\(Command\)/\1{\2}/' doc/openocd.texi
Change-Id: If692bbf7e546c5287f466a6aa6940d42b3d4655d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6150
Reviewed-by: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: jenkins
The commit 5280eb618a fixed all `adapter_khz` and
`adapter_nsrst_*` commands in the doc but missed grouping them. This
let the commands `adapter speed`, `adapter srst pulse_width`, and
`adapter srst delay` not indexed.
Tell texinfo about adapter sub-commands by grouping them in one.
Change-Id: Ida53c4f5cfe28827320c145c8d501d53e831623c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6134
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target mem_ap is a convenient way to access buses, memory and
peripherals behind an ARM AP.
The current implementation provides only access through OpenOCD
commands, because GDB remote protocol has to interact with a CPU
and has to operate on CPU states and registers.
Using GDB to access the memory is welcome, because GDB can resolve
the symbol's address from an ELF file and can nicely display the
content of complex struct and data types.
Extend mem_ap target with the bare minimal support for a remote
GDB connection, by emulating a fake basic ARM core. It means that
only a GDB that has support for ARM can be used (either 'aarch64',
'arm' or 'multiarch' GDB). This is not seen as a big limitation,
because the mem_ap target is mainly used on ARM based devices.
Add a minimalist register description for the fake CPU.
Fill the field 'debug_reason' as expected by GDB server.
Call the target halted event to reply to GDB halt requests.
For backward compatibility, don't open the GDB port by default. If
needed, it has to be specified at 'target create' or 'configure'
with the flag '-gdb-port'.
Change-Id: I5a1b7adb749746516f5d4ffc6193c47b70132364
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6034
Tested-by: jenkins
The comments currently used are not rendered.
Change-Id: I3fcfb6aee4dea9c4f9186a7aec70d382a1abd634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6133
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The documentation of OpenOCD is released under the GNU Free
Documentation License, version 1.2, with embedded some part of
OpenOCD code released under the GNU GPL-2.0-or-later.
Update doc/fdl.texi with latest minor fixes as in
https://www.gnu.org/licenses/old-licenses/fdl-1.2.texi
Update doc/openocd.texi and move here the license chapter title
Add license file LICENSES/preferred/GFDL-1.2 from
https://www.gnu.org/licenses/old-licenses/fdl-1.2.txt
and add the required tags for reference and tooling, coping
mostly from the Linux kernel license file in the 'deprecated'
folder.
Add a readme file to link to the existing texinfo copy of the
license.
Change-Id: Ief96e0686257be7a70d4eeec442848bd6494763d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5969
Tested-by: jenkins
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The code for ioutil has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I36dce1669ebe9acada5f9e752835c53e5214e3be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6089
Tested-by: jenkins
The code for oocd_trace has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I989f8345dee4ff2369bcf5e2e2ace86bbd5aa6a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6088
Tested-by: jenkins
The OpenOCD command line flag -p/--pipe was marked as deprecated
in release v0.5.0, more than 9 years ago.
We can reasonably expect that in these 9 years any user of OpenOCD
has already migrated to v0.5.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the command line flag already deprecated in v0.5.0.
Change-Id: I2faeb592ed2c2f67c2d3227f118093e39fcf4a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6084
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm920t cp15i' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I755c4283e13e125558fcd73b15fe20498eae95ca
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6083
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm720t cp15' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I2b325d0312d96ca5e5f0f1bad13bb162b3b75c52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6082
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
This is supposed to replace big part of armv7m_trace.[ch], since
TPIU is not only the one implemented in Cortex-M3 and M4.
Change-Id: I7588d16cbefe9cdb371c52fb0aa5cdfb48518804
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5858
Tested-by: jenkins
Quote: The ST-LINK TCP server is an application to share the debug
interface of a single ST-LINK board among several host applications,
typically a debugging tool and a monitoring tool.
Note: ST-Link TCP server does not support the SWIM transport.
ST-LINK TCP server allows several applications to connect to the same
ST-Link through sockets (TCP).
To use ST-LINK TCP server:
- using stlink-dap : use 'st-link backend tcp [port]'
- using hla : use 'hla_stlink_backend tcp [port]'
the default port value is 7184
Change-Id: I9b79f65267f04b1e978709934892160e65bd2d6d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5633
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD is based on a single main loop that schedules all the
activities.
At the execution of a TCL command, the timestamp is checked to
eventually trigger the polling of the targets. This means that by
executing a TCL command the polling can be triggered and detect a
change of target's state.
When openocd 'resumes' a target, the target can halt again by
hitting a breakpoint.
The 'resumed' event handler is started just after the target has
been resumed, but it triggers a polling before the execution of
its very first instruction.
If the polling finds the target halted, it will run the 'halted'
event handler, that will then be executed 'before' the pending
'resumed' handler.
In case of gdb, a 'continue' command will restart the target but,
polling (and halt detection) executed before the end of the resume
process will hide the halt. As a consequence, the gdb will not be
informed of the halt and will remains waiting as if the target is
still running without showing the prompt.
This can be verified by running on the target a firmware with a
loop, run openocd with a dummy 'resumed' event, and let gdb to set
a breakpoint in the loop. A 'continue' command will cause the
target to halt again by hitting the breakpoint at the next loop
iteration, but gdb will loose it and will not return the prompt.
openocd -f board/st_nucleo_f4.cfg -c \
'stm32f4x.cpu configure -event resumed {echo hello}'
arm-none-eabi-gdb -ex 'target remote :3333' -ex 'b *$pc' -ex c
Disable the polling while executing target's resume().
Document it and provide hints to developers to cope with future
implementation.
Change-Id: I3be830a8e7c2ef6278617cb4547a4d676b0ddeb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Габитов Александр Фаритович <gabitov@planarchel.ru>
Reviewed-on: http://openocd.zylin.com/6074
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
We have both the singular form, register_command(), and the plural form
register_commands().
Change-Id: I905ea83988b8ac70dd809b02d53b646aa4d66697
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6042
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The subpage "thelist" used to have a title "Pending and Open Tasks"
but the commit c41db358a0 changed it to "The List". With
@subpage, it now renders:
"The List of The List enumerates opportunities for"
instead of
"The List of Pending and Open Tasks enumerates opportunities for"
This commit fix it to
"The List enumerates opportunities for"
Change-Id: Ifee0dcd9b3c9f7e651a8748a7afda99eedea3c5c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6041
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We are talking about adapter connectivity in this chapter. It should
be "dongles" instead of "cables".
Change-Id: I7bd4307765517375caa2af86dfc929d0ef66c3e6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6040
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Commit ab90b87778 ("configure: remove AM_MAINTAINER_MODE,
effectively always enabling all the rules") removes the configure
flag '--enable-maintainer-mode' and its documentation, but have
left a reference to the removed subsection 'primermaintainermode'
and this triggers a warning in doxygen:
doc/manual/primer/autotools.txt:21: warning: unable to
resolve reference to 'primermaintainermode' for \ref
command
Remove the obsoleted paragraph.
Change-Id: I56e69ef033d546d159745bed1b47c6105827e7ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: ab90b87778 ("configure: remove AM_MAINTAINER_MODE, effectively always enabling all the rules")
Reviewed-on: http://openocd.zylin.com/6003
Tested-by: jenkins
The section name 'primerjtag' is used twice, causing doxygen to
complain:
warning: multiple use of section label 'primerjtag',
(first occurrence: doc/manual/primer/jtag.txt, line 107)
Rename one of them.
Change-Id: Id307915dbc51a7f647fab4fb28ab431e65344d61
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5999
Tested-by: jenkins
Doxygen complains about non-closed nested comments:
doc/manual/style.txt:423: warning: Reached end of file
while still inside a (nested) comment. Nesting level 1
(probable line reference: 149)
This is caused by the string '/**' that is interpreted as the
beginning of a comment.
Escape the string to not let doxygen consider it as a comment
While there, replace @code/@endcode with @verbatim/@endverbatim to
properly render the line.
Change-Id: If2a27c4cf659326e317cc4ac8c0b313e97e40432
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5996
Tested-by: jenkins
This adds some cosmetic changes to make the PDF User Manual look
proper.
Building it now requires Texinfo 5.0 which shouldn't be problematic
according to [0]. Commit 79fdeb37f4 is
effectively reverted.
[0] https://repology.org/project/texinfo/versions
Change-Id: I990bc23bdb53d24c302b26d74fd770ea738e4096
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5995
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This was flagged by lintian against the Debian package; the text stating
there are no invariant sections deviates from the official GNU wording.
Update it to match the text at the bottom of:
https://www.gnu.org/licenses/old-licenses/fdl-1.2.en.html
Change-Id: Ie222237a8eede24c1b71218b05e1513b74208a47
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/5974
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Real Time Transfer (RTT) is an interface specified by SEGGER based on
basic memory reads and writes to transfer data bidirectionally between
target and host.
Every target that supports so called "background memory access", which
means that the target memory can be accessed by the debugger while the
target is running, can be used.
RTT is especially of interest for targets which do not support Serial
Wire Output (SWO) (e.g. ARM Cortex-M0) or where using semihosting is
not possible (e.g. real-time applications) [1].
The data transfer is organized in channels where each channel consists
of an up- and/or down-channel. See [2] for more details.
Channels are exposed via TCP connections. One or more RTT server can be
assigned to each channel to make them accessible to an unlimited number
of TCP connections.
The current implementation does not respect buffer flags which are used
to determine what happens when writing to a full buffer.
Note that the implementation is designed in a way that the RTT
operations can be directly performed by an adapter (e.g. J-Link).
[1] https://devzone.nordicsemi.com/tutorials/6/
[2] https://www.segger.com/jlink-rtt.html
Change-Id: I8bc8a1b381fb74e08b8752d5cf53804cc573c1e0
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/4055
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
The only code dealing with tftp in OpenOCD was in eCos build, code
already dropped in commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") almost 8 years ago.
Drop tftp related documentation too.
Change-Id: I0defc8f844e74c90894dca04a652dcc497a520e1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5913
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
When trace capturing the trace is enabled using 'tpiu_config internal'
(via the internal mode), OpenOCD can collect the trace buffers then append
it to a specified file or named pipe and propagate the trace to 'tcl_trace'
command.
This change is allowing OpenOCD to stream the captured trace over TCP.
When using this configuration OpenOCD acts like a server and multiple
clients can connect and receive the captured trace.
Example on STM32F7 running at 216MHz:
itm port 0 on
tpiu config internal :3344 uart off 216000000
Change-Id: Idea43e7e26e87b98a33da7fb9acf7ea50fe3b345
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5345
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
To avoid code duplication, reorganize the code to replace
cti_configure() with adiv5_jim_mem_ap_spot_configure().
Reorganize 'struct arm_cti_object' and its sub-'struct arm_cti'
moving DAP and mem-AP info in a 'struct adiv5_mem_ap_spot'.
Replace cti_configure() with adiv5_jim_mem_ap_spot_configure().
Deprecate the use of '-ctibase' in favor of '-baseaddr'.
Change-Id: I43740a37c80de67c0f5e4dc79c3400b91a12e9e8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5869
Tested-by: jenkins
These are all the changes from https://github.com/riscv/riscv-openocd
(approximately 91dc0c0c) made just to src/target/riscv/*. Some of the
new code is disabled because it requires some other target-independent
changes which I didn't want to include here.
Built like this, OpenOCD passes:
* All single-RV32 tests against spike.
* All single-RV64 tests against spike.
* Enough HiFive1 tests. (I suspect the failures are due to the test
suite rotting.)
* Many dual-RV32 (-rtos hwthread) against spike.
* Many dual-RV64 (-rtos hwthread) against spike.
I suspect this is an overall improvement compared to what's in mainline
right now, and it gets me a lot closer to getting all the riscv-openocd
work upstreamed.
Change-Id: Ide2f80c9397400780ff6780d78a206bc6a6e2f98
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5821
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Evgeniy Didin
Daniel Anselmi
Antonio Borneo
Peter Lawrence
asier70
Tarek BOCHKATI
Yasushi SHOJI
Marc Schink
Paul Fertser
Jonathan McDowell
Tomas Vanek
Andreas Bolsch
Tim Newsome