jtagspi driver always used 3-byte addresses regardless of actual
device capcity. Now select 1- to 4-byte addresses depending on
device capacity.
Some devices need a special command to activate the 4-byte address
mode, a special command to accomplish this, and a further command
for setting device properties are added.
Additionally, restriction (start of range had to be page aligned)
removed.
Tested with XCS6SLX16 board and W25Q256FV in 3- and 4-byte address
modes.
Change-Id: I88b2877517a18dac460253ae6d97f3dded054e6c
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/4876
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The busy flag must be polled after each half-page write.
At low clock speeds, no issue is observed when the poll
is omitted, because the writes complete before the next
write begins. But at high clock speeds the subsequent
writes would overlap and cause the operation to fail.
The status polls are done on the target for efficiency,
since the half-pages are very small.
Change-Id: Ia1e9b4a6a71930549b3d84a902744ce6e596301b
Signed-off-by: Jimmy <nhminus@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5598
Tested-by: jenkins
Reviewed-by: Jelle De Vleeschouwer
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
Commit 64c2e03b23 ("flash/nor: improved API of flash_driver.info
& fixed buffer overruns") changes the prototype of the function
psoc6_get_info() but didn't update the list of parameters in the
doxygen comment.
Fix the doxygen comment.
Change-Id: I1dce018b60d080973c5e351490d4d7baba422d74
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Reviewed-on: https://review.openocd.org/c/openocd/+/6620
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The header files under src/helper/ can currently be included with
either
#include <bits.h>
or
#include <helper/bits.h>
This is because we specify both "src/" and "src/helper/" directories
as include directories. Some files name under "src/helper/", such as
types.h, log.h, and util.h are too generic and could be ambiguous
depending on the search path.
This commit remove "src/helper/" from our include dir and make C files
include explicitly.
Change-Id: I38fc9b96ba01a513d4a72757d40007e21b502f25
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6507
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The include file 'armv7m.h' includes 'arm_adi_v5.h' only to get
the definition of 'struct adiv5_ap', but doesn't need the struct
content.
Reducing the cross dependencies speeds-up the compile time during
code development by avoiding re-compiling file.
Relax the dependency by locally declaring 'struct adiv5_ap' in
'armv7m.h' and remove the include of 'arm_adi_v5.h'.
Fix the other files that have now lost the includes file that
'arm_adi_v5.h' depends from.
Change-Id: Ic0d40b17db6045fa43f348bda83eaf211a6b347d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6468
Tested-by: jenkins
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This partially reverts commit 1247eee4e6.
There is no reasonable use cases where work-area should be enabled
and working, and it can't be used for the flash loader.
Instead of introducing driver specific property, users can disable
flash load by disabling work-area, for example by setting it to 0.
But still we keep the function stm32l4_write_block_without_loader
to be used when workarea is not available (no sufficient size or zero)
Change-Id: Ibb046c74df354c6067bac978e8ef7efb47d9fd2b
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6569
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For STM32L552xC devices with 256K flash:
dual bank mode is activated if DB256 is set
page size is 2KB if DBANK is set
For parts with 512K (aka STM32L5x2xE):
DBANK controls both of dual/single bank mode and page size as well.
Change-Id: I8be668d5552fefe81acffaf2e3e35ef5e938162e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Patrik Bachan <diggit@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/317/
Reviewed-on: https://review.openocd.org/c/openocd/+/6538
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
stm32l4_work_area struct is shared between the loader and stm32l4x flash driver
'*wp' and '*rp' pointers' size is 4 bytes each since stm32l4x devices have
32-bit processors.
however when used in openocd code, their size depends on the host
if the host is 32-bit, then the size is 4 bytes each.
if the host is 64-bit, then the size is 8 bytes each.
to avoid this size difference, change their types depending on the
usage (pointers for the loader, and 32-bit integers in openocd code).
Change-Id: I0a3df4bb4bf872b01cdb9357eb28307868d7d469
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6556
Tested-by: jenkins
Reviewed-by: Yestin Sun <sunyi0804@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
CPU2 (Cortex-M0+) is supported only with non-hla adapters because it is on AP1.
Using HLA adapters armv7m.debug_ap is null, and checking ap_num triggers
a segfault.
Change-Id: I501f5b69e629aa8d2836b5194063d74d5bfddb12
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Fixes: https://github.com/STMicroelectronics/OpenOCD/issues/6
Reviewed-on: https://review.openocd.org/c/openocd/+/6535
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
add the target assigned to the flash bank at creation
this is useful in daisy chains, to filter out the target banks.
Change-Id: Ic39e44914e34bb62991783762e5a65ef8871e82f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6426
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The 'flash list' command returns the driver name as flash name which seems
to be incorrect, the proposal is:
- to fix this by returning the flash name
- and add a new item 'driver' in the returned list
example:
before the change
> flash list
{name stm32l4x base 134217728 size 0 bus_width 0 chip_width 0}
{name stm32l4x base 201326592 size 0 bus_width 0 chip_width 0}
{name stm32l4x base 200933376 size 0 bus_width 0 chip_width 0}
after the change
> flash list
{name stm32l5x.flash_ns driver stm32l4x ...}
{name stm32l5x.flash_alias_s driver stm32l4x ...}
{name stm32l5x.otp driver stm32l4x ...}
Change-Id: I6d307b73c457549981a93c260be344378719af82
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6425
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
STM32WB1x devices has a single flash bank up to 320 KB (page 2KB)
note: STM32WB5x/WB3x are single banks as well but do have 4KB as page size.
note: remove the assert that checks if max_mages is power of two, because
STM32WB1x flash size is not a power of 2
Change-Id: Ib514cf989ecb819d25d1c4a65d641d0a1a3d9f18
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6129
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device has single bank flash architecture up to 64KB (page 2KB)
reference: RM0444 rev 5
Change-Id: Ia213c01accb950fcbb7519e08057dae11b4443dd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6128
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
switching to C loader instead of the assembly version will enhance readability
will reduce the maintenance effort.
besides the switch to C loader, we added a new parameters to the loader
like flash_word_size and flash_sr_bsy_mask in order to support properly
STM32U5x and STM32G0Bx/G0Cx in dual-bank mode.
Change-Id: I24cafc2ba637a065593a0506eae787b21080a0ba
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6109
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
If the remaining memory for the buffer is less than 256 bytes,
the memory allocated for the write algorithm in the target is not freed.
Fixes: ba131f30a0 (Flash driver for STM32G0xx and STM32G4xx)
Change-Id: Ic649f6c39799d76725b0c69ff3a009a3f510e17f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6486
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
according the RM0453, the second core have a different Flash CR and SR
registers for flash operations (called C2CR and C2SR).
so we need to a different flash_regs than older L4 devices.
@see stm32wl_cpu2_flash_regs
the C2CR register don't contain LOCK and OPTLOCK bits, and this explain
the addition of new register index called STM32_FLASH_CR_WLK_INDEX to
look-up the CR with lock, to be used in locking/unlocking the flash.
note: DBGMCU_IDCODE cannot be read using CPU1 (Cortex-M0+) at AP1,
to solve this read the UID64 (IEEE 64-bit unique device ID register)
Change-Id: Ifb6e291bf97f814f0b9987b2c40f3037959f7af4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6050
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
When running OpenOCD with -fsanitize=undefined, a warning is emitted
for an bit-shifting operation whose result cannot be stored in a
signed integer.
This is because (1 << 31) overflows a signed integer, which is
undefined behavior. By making each of the bit masks act on an
unsigned number, the warning is avoided.
Whether this warning emitted by UBSan would ever manifest into a real
error is debatable, but fixing this does make UBSan happy.
Change-Id: I0455a26b234cb4f5e239a6ba90023d28380e9464
Signed-off-by: Sebastiaan de Schaetzen <sebastiaan.de.schaetzen@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6429
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this device has a dual bank flash architecture up to 512 KB (page 2KB)
reference: RM0444 Rev 5
notes:
- 128k variant is always single bank
- 256k variant flash is contiguous (no gap) in dual bank mode
- BKER is bit 13 vs bit 11 for other devices
> added cr_bker_mask in stm32l4_flash_bank struct
- BSY2 for bank 2 operations
> added sr_bsy_mask in stm32l4_flash_bank struct
> proposed optimization: always wait for (BSY1 | BSY2) with
STM32G0Bx/G0Cx devices only (for L4+ devices BSY2=PEMPTY)
TODO: update flashloader to use the proper BSY bits
temporarily don't use the loader in dual bank mode
Change-Id: I54b0c93b494e7209da818791d15edd8cd42c2732
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6036
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
This struct element is replaced by the usage of F_HAS_L5_FLASH_REGS flag:
since over this driver stm32l4_flash_regs is the default register layout,
and the only exception is STM32L5 family,
so it's simpler to manage it using a flag.
Note: the same flag will be used with STM32U5 devices, as they have
the same registers layout, which explains the move of stm32l5_s_flash_regs
before the switch(device_id) in order to not re-write this for STM32U5.
Change-Id: I3b67a6f558d9350f609a22524012b6fceb7de7c2
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6435
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this capability permits to program the flash if we cannot reserve a workarea.
the introduction the command 'stm32l4x flashloader <bank_id> [enable|disable]'
helps to automatically skip using the flashloader if needed.
Change-Id: Id29213c85ee5c7c487cfee21554f5a7ea50db6c9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6273
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
when RDP level is 0.5 the provided work-area should reside in non-secure RAM
to ensure that:
- add a hint in the driver level
- reduce the usage of secure RAM only when TZEN=1 and RDP is not 0.5
(check the target configuration file)
Change-Id: Idbf2325e609b84ef8480eefdb49a176fdf7e07c7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6035
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STM32L5 flash memory is aliased to 0x0C000000, this address mapping
is used for secure applications. (0x08000000 for non-secure)
this change allows the programming of secure and non-secure flash
when trustzone is enabled and RDP level is 0
Change-Id: I89d1f1b5d493cf01a142ca4dbfef5a3731cab96e
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5936
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
auto re-probing is ensured by having optr cache set in the
last probe operation.
this will help to detect if flash options have been modified by the
running application or by the user using direct register access.
Change-Id: I05cd7ab9e83a7fc26ac6cff175b3c11b0efa2eb5
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5935
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this command will help to enable/disable or display the TrustZone security,
using the TZEN option bit.
Note: This command works only with devices with TrustZone, eg. STM32L5.
Note: This command will perform an OBL_Launch after modifying the TZEN.
Change-Id: I4aef15bf57d09c1658d37858143d23b1d43de1f0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5542
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
in line 1391, get_stm32l4_bank_type_str(bank) will always output the same
value "Flash single" since the variable stm32l4_info->dual_bank_mode is false
by default, stm32l4_info->dual_bank_mode will be set correctly afterward
in the switch case at line 1467
thus the need to remove the usage of get_stm32l4_bank_type_str(bank) before
stm32l4_info->dual_bank_mode initialization.
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Change-Id: Ia8dc7e144e0ded6143682eb514c247f27859ff81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6411
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: Ia7fe9c4017108616f21676f115f151ac62924205
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6423
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: I972da1a75ba7c41c1b714c2429289c3d24594235
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6422
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: Ibfe95ce73f147f467de8de23e9573ef0179aed96
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6421
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: I14061cb48da6bac13f9d2896190136f5784b8c07
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6424
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the usage of COMMAND_PARSE_NUMBER is safer in COMMAND_HANDLERs since it provides
better error checking than strto** functions.
Change-Id: I7e113b06b74f2d8d9cc4c0ce1957994a1c49c964
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6419
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Remove useless setting of the 'is_erased' flag after a flash
modification. Also, remove code that erroneously depends on
this flag.
Keep the flag for now since it is still used by the
erase_check() functionality.
See commit 07da3b3913
Change-Id: Ia046905bc9e0cb2572145f19251c3e10c4e2d553
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6279
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new helper to make the code more readable.
Change-Id: I11b2a79dbc6f93f6cfde382bcc00dd7ff710d908
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6375
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This warning about "maybe uninitialized" variable
used to pop up on certain versions of GCC.
Change-Id: I1cf43b9600885d507afc1dc042322a06751fe146
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6290
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new checkpatch can automatically fix the code, but this
feature is still error prone and not complete.
Patch generated automatically through the new checkpatch with
flags "--types CONSTANT_COMPARISON --fix-inplace".
Some Yoda condition is detected by checkpatch but not fixed; it
will be fixed manually in a following commit.
Change-Id: Ifaaa1159e63dbd1db6aa3c017125df9874fa9703
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6355
Tested-by: jenkins
For the remaining NULL comparisons, remove then manually.
While there, make more readable a loop, by moving the assigment
out of the loop condition.
Change-Id: I44193aaa95813156a3a79c16b80e1ad333dc1eaf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6353
Tested-by: jenkins
Patch generated automatically through a modified checkpatch that
detects the patterns
if (NULL == symbol)
if (NULL != symbol)
and through flags "--types COMPARISON_TO_NULL --fix-inplace".
The unmodified checkpatch detects this pattern as Yoda condition,
but it's odd fixing it as Yoda condition and then again as NULL
comparison. This triggered the modification to the script.
Change-Id: I5fe984a85e9c4fc799f049211797aef891ebce18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6352
Tested-by: jenkins
Patch generated automatically through the new checkpatch with
flags "--types COMPARISON_TO_NULL --fix-inplace".
This only fixes the comparisons
if (symbol == NULL)
if (symbol != NULL)
The case of NULL on the left side of the comparison is not tested.
Some automatic fix is incorrect and has been massaged by hands:
- if (*psig == NULL)
+ if (*!psig)
changed as
+ if (!*psig)
Change-Id: If4a1e2b4e547e223532e8e3d9da89bf9cb382ce6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6351
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
Fix the remaining Yoda conditions, detected by checkpatch but not
fixed automatically.
While there, apply minor style changes.
Change-Id: I6e1978b89c4d56a20aceaeb2b52968eb6384432a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6356
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
There are ~900 Yoda conditions to be aligned to the coding style.
For recurrent Yoda conditions it's preferable using a trivial
script in order to minimize the review effort.
E.g. comparison of uppercase macro/enum with lowercase variable:
- ...(ERROR_OK == retval)...
+ ...(retval == ERROR_OK)...
Patch generated automatically with the command:
sed -i \
's/(\([A-Z][A-Z0-9_]*\) \([=!]=\) \([a-z][a-z0-9_]*\))/(\3 \2 \1)/g' \
$(find src/ -type f)
While there, remove the braces {} around a single statement block
to prevent warning from checkpatch.
Change-Id: If585b0a4b4578879c87b2dd74d9e0025e275ec6b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6354
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Each driver is almost self-contained, with no cross dependency.
Changing symbol names in one drive does not impact the other.
Change-Id: Ic09f844f922a35cf0a9dc23fcd61d035b38308b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6299
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The struct cfi_spansion_pri_ext has few symbols in CamelCase.
Change all them accordingly to OpenOCD coding style.
Patch created automatically with the script below:
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
VppMin vpp_min
VppMax vpp_max
TopBottom top_bottom
TmpBlkUnprotect tmp_blk_unprotected
SimultaneousOps simultaneous_ops
SiliconRevision silicon_revision
PageMode page_mode
EraseSuspend erase_suspend
BurstMode burst_mode
BlkProtUnprot blk_prot_unprot
BlkProt blk_prot
EOF
) | while read a b; do
sed -i "s/$a/$b/g" src/flash/nor/*cfi*
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I135331539ca9aa84765fdffc51c87a07a46ee77a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6298
Tested-by: jenkins
The current implementation fails due to the assert() statements in
get_stm32l4_rev_str() and get_stm32l4_bank_type_str(). Rearrange the
code in order to fix the problem.
Change-Id: If19c648dec8ddd3ef2fb801150114104b34c3bf2
Signed-off-by: Marc Schink <dev@zapb.de>
Fixes: 64c2e03b23 ("flash/nor: improved API of flash_driver.info & fixed buffer overruns")
Reviewed-on: http://openocd.zylin.com/6326
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In these drivers we read CPUID to check the Cortex-M PARTNO,
but now the PARTNO is stored in struct cortex_m_common.core_info.
Change-Id: I5bb3b95210ab6e23b8e1252686dd81015740bf68
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6240
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In target/arm.h the struct arm do contain 3 flags to retain architecture
version for some tweaks.
The proposal is to have only one enumerated flag 'arch' for the same purpose.
Change-Id: Ia5d5accfed8158ca21eb54af2fdea8e36f0266ae
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
1) The API of "info" callback in "struct flash_driver" has been
improved. Fixed buffers for strings
2) Removed the calls to snprintf() from the flash_driver.info
implementations. Many of them were used in an unsafe manner
(buffer overruns were possible).
Change-Id: I42ab8a8018d01f9af43c5ba49f650c3cb5d31dcb
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6182
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
this is not a bug fix, this for loop will issue only one match
adding the break will save unnecessary more loops.
Change-Id: Ic1484ea8cdea1b284eb570f9e3e7818e07daf5cd
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6248
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
For both:
- TCL proc that redirect deprecated commands to the new commands,
- TCL proc used internally and not supposed to be exposed to user,
add their name to the list of commands that should be hide by the
telnet auto-complete.
Change-Id: I05237c6a79334b7d2b151dfb129fb57b2f40bba6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6195
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Nowadays, when it's difficult to buy STM32F030,
the use of GD32F130 seems to be an interesting functional alternative.
This is cortex-M3 and it works with the stm32f1x driver, but unfortunately not fully.
The main difference is another offset of user option bits
(like WDG_SW, nRST_STOP, nRST_STDBY) in option byte register
(FLASH_OBR/FMC_OBSTAT 0x4002201C).
Any use of functions like lock or unlock results in change default values of the those bits stored in flash.
Thus broken microcontroller is malfunctioning, e.g. flash block programming is interrupted
by unexpected active hardware watchog (after 0.4s).
This patch is a simplified version of #4592 done by Dominik Peklo (http://openocd.zylin.com/#/c/4592/).
GigaDevice GD32F1x0 & GD32F3x0 series devices share DEV_ID
with STM32F101/2/3 medium-density line,
however they use a REV_ID different from any STM32 device,
so can be succesfully detected.
Change-Id: I252cdf738d94983b70676a3497326f90c329e292
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Reviewed-on: http://openocd.zylin.com/6164
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove a use of AH_BOTTOM from configure.ac. This macro is used by
autoheader to add '#include' of some include file to the end of
config.h.in and then to config.h. OpenOCD can be built with a custom
config.h, so it's preferable to move these '#include' statement directly
in the C files that need them dropping this unneeded dependency.
It also causes problems when I want to use the gnulib library (which
comes with its own Makefile, and does not have the same include path as
the top-level Makefile).
So this change touches a lot of files, but is actually really simple. It
does not affect functionality at all.
Change-Id: I52c70bf15eb2edc1dd10e0fde23b2bcd4caec000
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/6171
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace the "struct command *parent" parameter with a string that
contains the command prefix.
This abstracts the openocd code from the knowledge of the tree of
struct command.
This also makes unused the function command_find_in_context(), so
remove it.
Change-Id: I598d60719cfdc1811ee6f6edfff8a116f82c7ed6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5668
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
introduction of 'enum stm32l4_rdp' enumerating possible RDP levels for
devices with and without TrustZone.
also in 'stm32l4_flash_bank' structure we added and rdp and tzen members
to store read values by the helper 'stm32l4_sync_rdp_tzen'
these new members are used to display security and protection status
while probing the flash.
Change-Id: Icf883189715278a3323fe210d295047678b16592
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5541
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In flash/nor/cfi.c:835 struct cfi_info is allocated by malloc(). As
write-mem was uninitialized the pointer pointed to an out of range
address, which led to a segmentation fault and crashed openocd.
This happened during flash-command of an external flash-bank, using
cfi.
Use calloc() instead.
While on it check for NULL return and remove unnecessary initialzation.
Change-Id: I0e2ffb90559afe7f090837023428dcc06b2e29f6
Signed-off-by: Mischa Studer <mischa.studer@csa.ch>
Reviewed-on: http://openocd.zylin.com/6070
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This removes some warnings which prevent a successful build with -Werror
which is enabled by default. I'm using gcc 11, so maybe others are not
getting this warnings yet.
In src/flash/nor/numicro.c the debug messages were misleadingly indented.
In src/target/arm920t.c the array size where smaller than expected from
the receiving function.
Change-Id: I66f5c6a63beb9f9416e73b726299297476c884d8
Signed-off-by: Rene Kita <git@rkta.de>
Reviewed-on: http://openocd.zylin.com/6104
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is specially needed when, in the probe routine, device is not
found among the stm32l4_parts. In this case, the stm32l4_flash_bank->part_info
is undefined and inadvertentanly used afterwards:
part_info = stm32l4_info->part_info;
If the stm32l4_flash_bank is zero init, the probe routine checks for
the validity of the part_info field in the previous struct and correctly
detects the unsupported (or not found) condition, raising an error
rather than a SIGSEGV
Change-Id: I7d9d669fb3fa7f8f0903acd60046966b4acb0031
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6103
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is no good reason to use macros instead of static inline functions. The
current code is hard maintain. For example, it changes variables outside of the
macro scope. Also, it is conflicting with the C coding style.
Change-Id: I5ac9d2ae076ef73c176d4e32b2e7e0a99fa875ab
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6046
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The C style guide forbids typedef'd structs, see 'Naming Rules'.
Change-Id: I983dd52307136d1b5adb58d8c44c0c14422d31e2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6032
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
using gcc 9.3 on ubuntu focal fossa with -Werror=maybe-uninitialized
we get this error:
/src/flash/nor/stmqspi.c: In function ‘read_flash_id’:
/src/flash/nor/stmqspi.c:1948:6: error: ‘retval’ may be used uninitialized
Change-Id: Ifd8ae60df847fc61e22ca100c008e3914c9af79b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Reviewed-on: http://openocd.zylin.com/6012
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
The relative path should have three times '..'.
Issue identified by doxygen:
src/flash/nor/max32xxx.c:85: warning: include file
../../contrib/loaders/flash/max32xxx/max32xxx.inc not
found, perhaps you forgot to add its directory to
INCLUDE_PATH?
Change-Id: Ie7b4948c6770b8acb9eff26e08eea32945ebb219
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5997
Tested-by: jenkins
The warning message regarding wrong verification checksum for LPC2000, claims that the verification will fail, but the checksum written correctly by openocd. Clarify this in the warning message.
Change-Id: I929ac767f7f9fdad9bace250c8c04a776462800a
Signed-off-by: Luca Lindhorst <l.lindhorst@wut.de>
Reviewed-on: http://openocd.zylin.com/5956
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The git preliminarily version of clang 12.0.0_r370171
f067bc3c0ad6 reports an error in the expansion of the macro
SMI_READ_REG():
error: '(' and '{' tokens introducing statement expression
appear in different macro expansion contexts
[-Werror,-Wcompound-token-split-by-macro]
Remove one intermediate macro expansion to make clang happy.
Change-Id: I8ae6d9c18808467ba8044d70cbf0a4f76a18d3e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5958
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
flash_regs table is introduced within stm32l4_flash_bank struct in order
to get correct register offsets, by using the driver internal function
'stm32l4_get_flash_reg_by_index'.
To use efficiently register indexes, stm32l4 _[get|read|write]_flash_reg
functions are surcharged to accept register indexes.
IMPORTANT: stm32l4_write_option is not surcharged, and they always accept
the option register offset.
tested on NUCLEO-G474RE and STM32L4R9I-DISCO
Change-Id: I739d3e97d63b831af6aa569c5629db0000209551
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5509
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
PSoC6 erases flash to 0x00 not more common 0xff, so a device
with erased flash loads xPSR.T=0 from the zeroed reset vector.
Wrong thumb bit value caused a target algorithm failed with HardFault.
The low level write to xPSR solved the problem only if xPSR cached
copy was not marked dirty.
Later commit 49bd64347a fixed T setting
for all Cortex-M target algorithms.
Since 49bd64 this part of code is useless as xPSR target_start_algorithm()
sets always xPSR dirty so the effect of the low level write is eliminated
(and proper setting of thumb bit is ensured in target_start_algorithm())
Change-Id: I68aea5e921fbc6203f2fe91a45f10d22869327de
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5875
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I52d46ed6d4c9b98a7152eb23274c836416f409a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Warning: line 679, column 4
4th function call argument is an uninitialized value
Change-Id: If62d96e1595be945c8e17885bb402e820fb1ec7b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5903
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
HWID is a part of 32 bit CONFIGID register. hwid member of struct nrf5_info
was typed uint32_t to enable direct CONFIGID read and masked afterwards.
Change to uint16_t to unify with hwid in struct nrf5_device_spec
and RM description.
Change-Id: Ib720d3ce23c301aee41d074ea78a6f00a23aed68
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5589
Tested-by: jenkins
nRF52 devices indicate a flash error by emitting hard fault
exception (unlike nRF51 series).
Change error message when NVMC READY read fails. A hard fault
from flash erase/write operation is detected here.
Check exit point of the flash write algo to ensure a failed
write is recognised.
Change-Id: I637eda268a6bf45f7f41bcb9dcd82db8f5cb41b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5587
Tested-by: jenkins
nRF51 devices have a clumsy flash protection based on UICR CLENR0.
A code running in RAM can write to a protected flash region without
any hint the protection gets violated.
NVMC flash page erase obeys protection setting but fails absolutely
silently.
Before this change the first problem was not addressed in the code.
To justify the second one, protection was loaded during probe,
after protection setting and after a mass erase.
Move protection updates to the beginning of erase/write operation
and limit them to nRF51 series only. Check for protected sectors
before write.
The change also fixes the problem of 'nrf5 mass_erase' on
nRF52833/840 devices. They use ACL flash protection, which is not
supported in nrf5 driver. mass_erase then looked like it failed.
Change-Id: Ie58cda68eb104d410b02777c3df5b343408e2666
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5522
Tested-by: jenkins
Protection setting has not ever worked. UICR CLENR0 register cannot
be simply written but has to programmed because it resides in UICR
page of the flash.
Enable flash programming before writing CLENR0 and set back to r/o
afterwards.
Inform the user that reset might be required.
Change-Id: Ib0f96c74ba3583ac33f4394ddb57d8c8895adf53
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5586
Tested-by: jenkins
Tarek BOCHKATI
Andreas Bolsch
Jimmy
Antonio Borneo
Yasushi SHOJI
Oleksij Rempel
Wealian Liao
Sebastiaan de Schaetzen
Marc Schink
Jan Matyas
R. Diez
Peter Lawrence
asier70
Tim Newsome
Tomas Vanek
Mischa Studer
Rene Kita
Raúl Sanchez Siles
Tarek BOCHKATI
Luca Lindhorst