this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this capability permits to program the flash if we cannot reserve a workarea.
the introduction the command 'stm32l4x flashloader <bank_id> [enable|disable]'
helps to automatically skip using the flashloader if needed.
Change-Id: Id29213c85ee5c7c487cfee21554f5a7ea50db6c9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6273
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this command will help to enable/disable or display the TrustZone security,
using the TZEN option bit.
Note: This command works only with devices with TrustZone, eg. STM32L5.
Note: This command will perform an OBL_Launch after modifying the TZEN.
Change-Id: I4aef15bf57d09c1658d37858143d23b1d43de1f0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5542
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Use a command group 'ft232r' with subcommands instead of individual
commands with 'ft232r_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I0dbeb4716330c83f8ce89b0d054eb0286b887bdf
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6409
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'usb_blaster' with subcommands instead of individual
commands with 'usb_blaster_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I2ae3d96ba864c20d7db67c74677781a62bfc4eb5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6407
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'buspirate' with subcommands instead of individual
commands with 'buspirate_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Id999d4ba276af576fb22b76052f3c0a1f3e1b876
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6404
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'bcm2835gpio' with subcommands instead of individual
commands with 'bcm2835gpio_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I8f7b14273b1b2813ac3c9704605d175fa2053008
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6396
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'jtag_dpi' with subcommands instead of individual
commands with 'jtag_dpi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I19271546235a3c6737f975976a0bf0a2f66cbbe7
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6394
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'xlnx_pcie_xvc' with subcommands instead of individual
commands with 'xlnx_pcie_xvc_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I0deaaa14ed14f65bf356f3c248331bfab472f08d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'presto' with subcommands instead of individual
commands with 'presto_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I883d8d87fd457d29cee8d12cd80f2e6c405e8f42
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6390
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'remote_bitbang' with subcommands instead of individual
commands with 'remote_bitbang_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I2692320f19c8a357112a365db6ca7e13cd6ad411
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6389
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'openjtag' with subcommands instead of individual
commands with 'openjtag_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Ie1b1bf0b7c03e7703cfb074e554288384bf7b1b9
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6387
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'parport' with subcommands instead of individual
commands with 'parport_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I4cb7096a8ba8d6cd7a6dc970862cd73c32b5c0a2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6385
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds documentation for the bcm2835 interface configuration
parameters to the user manual. Documentation format is based on
the FTDI interface section, and was taken from the descriptions
in the driver source code.
Change-Id: I77b09b8bd44d8e8fe9cc5fb9de3c3a30550d943c
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6376
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Due to Freenode takeover it's likely that most of our users are going to
seek support on Libera in the nearest future.
Change-Id: I98db95bab51f4ef2ac854bf521468d22b2794e56
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6297
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Use a command group 'ftdi' with subcommands instead of individual
commands with 'ftdi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I93a0ae7070226cd2fdea566effeb14a141269de8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6332
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Added support for reading and writing 64-bit data items
using TCL commands "mem2array" and "array2mem". Until now,
data items only up to 32 bits were supportd.
- Cleaned up functions target_array2mem() and
target_mem2array(), especially data types of variables
and variable declarations (scope).
Change-Id: Ia0ba427804f8fd8d7568f12714ab36984d6d5e24
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6286
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
To improve readability and to push more uniform code style.
Prefer 'if (false) {...}' for unused code so it get checked by the
compiler.
Define preferred indentation for 'switch' statement.
Require balanced brackets in 'if/else'.
Report the max line length.
Report the formatting strings for stdint/inttypes types.
Report the type 'target_addr_t'.
Prefer 'unsigned int' to 'unsigned'.
Change-Id: I0192a4ed298f6c6c432764fdd156cffd4b13fc89
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6203
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
pico-debug is not a board; it is a virtual CMSIS-DAP adapter that
runs on the same RP2040 also being debugged. This is possible due
to pico-debug running on the normally-dormant second Cortex-M0+
core (Core1), providing debugging of the first core (Core0).
As such, it could be used on a variety of RP2040-based boards.
Since a flash driver is useful (if not essential), a flash driver
is included. This driver code originated on RPi's bespoke OpenOCD
fork; lipstick was added to this particular pig to make it more
presentable on OpenOCD proper.
no new Clang analyzer warnings
Change-Id: I31f98b5ea1664f0adfbc184b57efba963acfb958
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/6075
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Nowadays, when it's difficult to buy STM32F030,
the use of GD32F130 seems to be an interesting functional alternative.
This is cortex-M3 and it works with the stm32f1x driver, but unfortunately not fully.
The main difference is another offset of user option bits
(like WDG_SW, nRST_STOP, nRST_STDBY) in option byte register
(FLASH_OBR/FMC_OBSTAT 0x4002201C).
Any use of functions like lock or unlock results in change default values of the those bits stored in flash.
Thus broken microcontroller is malfunctioning, e.g. flash block programming is interrupted
by unexpected active hardware watchog (after 0.4s).
This patch is a simplified version of #4592 done by Dominik Peklo (http://openocd.zylin.com/#/c/4592/).
GigaDevice GD32F1x0 & GD32F3x0 series devices share DEV_ID
with STM32F101/2/3 medium-density line,
however they use a REV_ID different from any STM32 device,
so can be succesfully detected.
Change-Id: I252cdf738d94983b70676a3497326f90c329e292
Signed-off-by: asier70Andrzej Sierżęga <asier70@gmail.com>
Reviewed-on: http://openocd.zylin.com/6164
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 7a731eb637 ("Added HostOS variable"), merged in 2009,
adds a TCL global variable 'ocd_HostOS' that reports in a string
the OS of the host.
This was proposed as a workaround for jimtcl that didn't define
the standard TCL variable 'tcl_platform(os)'.
With commit 42f3fb7b7f46 ("Determine platform_tcl() settings with
configure"), merged in 2010 and part of jimtcl 0.70 issued in
early 2011, jimtcl provides the requires TCL standard variable
'tcl_platform(os)'.
The variable 'ocd_HostOS' has never been used by any TCL script
distributed with OpenOCD.
Drop the TCL variable 'ocd_HostOS'.
Change-Id: I27858de35cc9d30df97145ca1ccd24877be4af11
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6189
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix the warning below by adding a '.' after xref in line 10184:
./doc/openocd.texi:10184: warning: `.' or `,' must follow @xref, not c
Change-Id: Ibd976ae61cf6845e925b839321444dcb25a3c04a
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6179
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
fix the warning below by adding a '.' after xref in line 4517:
../code/doc/openocd.texi:4517: warning: `.' or `,' must follow @xref, not )
Change-Id: I6e529c7e83c9f912e1dd899abf5f630c90b583d9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6174
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The mode of command 'ftdi_layout_signal' is set to COMMAND_ANY in
[1] and the command has no constraints that limits its use to the
config phase only.
But [2] documents it as '{Config Command}'.
Update the documentation to report the correct mode '{Command}'.
[1] commit f5e97b5e1b ("Add FTDI JTAG driver using MPSSE layer")
[2] commit 76afadeb7b ("doc: Add documentation for the ftdi driver")
Change-Id: I6b14aebb98e48f7080c585f3df881714bb188af0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6155
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The command 'ftdi_location' is deprecated and a TCL procedure is
in place to direct the user to the replacement command.
There is no need to document the deprecated command.
Remove 'ftdi_location' from the documentation.
Change-Id: Ia431c6b0e7444d3f3288c088429bfb47089ff1b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6154
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Some command that is only valid during configuration is documented
as generic command.
Annotate them as {Config Command} in the documentation.
Change-Id: Ifdbb6ec89b945e3d7adce94af379d94f511a64b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6153
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I41a8447d487ec8f6f32c2babcbc73ac21c769344
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6152
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every Command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I797e8d9f5ab0aa1936f350b340d3bdd52373f5aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6151
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Both 'Command' and '{Command}' are in use, with the following
statistics:
0 @deffnx {Command}
45 @deffn {Command}
31 @deffnx Command
382 @deffn Command
While 'Command' is the most popular, prefer the version within
curly-brackets that has to be used for multi-word definition like
'{NAND Driver}', '{Config Command}', '{FPGA Driver}', ...
Patch generated through:
sed -i 's/^\(@deffn \)\(Command\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx \)\(Command\)/\1{\2}/' doc/openocd.texi
Change-Id: If692bbf7e546c5287f466a6aa6940d42b3d4655d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6150
Reviewed-by: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: jenkins
The commit 5280eb618a fixed all `adapter_khz` and
`adapter_nsrst_*` commands in the doc but missed grouping them. This
let the commands `adapter speed`, `adapter srst pulse_width`, and
`adapter srst delay` not indexed.
Tell texinfo about adapter sub-commands by grouping them in one.
Change-Id: Ida53c4f5cfe28827320c145c8d501d53e831623c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6134
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target mem_ap is a convenient way to access buses, memory and
peripherals behind an ARM AP.
The current implementation provides only access through OpenOCD
commands, because GDB remote protocol has to interact with a CPU
and has to operate on CPU states and registers.
Using GDB to access the memory is welcome, because GDB can resolve
the symbol's address from an ELF file and can nicely display the
content of complex struct and data types.
Extend mem_ap target with the bare minimal support for a remote
GDB connection, by emulating a fake basic ARM core. It means that
only a GDB that has support for ARM can be used (either 'aarch64',
'arm' or 'multiarch' GDB). This is not seen as a big limitation,
because the mem_ap target is mainly used on ARM based devices.
Add a minimalist register description for the fake CPU.
Fill the field 'debug_reason' as expected by GDB server.
Call the target halted event to reply to GDB halt requests.
For backward compatibility, don't open the GDB port by default. If
needed, it has to be specified at 'target create' or 'configure'
with the flag '-gdb-port'.
Change-Id: I5a1b7adb749746516f5d4ffc6193c47b70132364
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6034
Tested-by: jenkins
The comments currently used are not rendered.
Change-Id: I3fcfb6aee4dea9c4f9186a7aec70d382a1abd634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6133
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The documentation of OpenOCD is released under the GNU Free
Documentation License, version 1.2, with embedded some part of
OpenOCD code released under the GNU GPL-2.0-or-later.
Update doc/fdl.texi with latest minor fixes as in
https://www.gnu.org/licenses/old-licenses/fdl-1.2.texi
Update doc/openocd.texi and move here the license chapter title
Add license file LICENSES/preferred/GFDL-1.2 from
https://www.gnu.org/licenses/old-licenses/fdl-1.2.txt
and add the required tags for reference and tooling, coping
mostly from the Linux kernel license file in the 'deprecated'
folder.
Add a readme file to link to the existing texinfo copy of the
license.
Change-Id: Ief96e0686257be7a70d4eeec442848bd6494763d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5969
Tested-by: jenkins
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
The code for ioutil has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I36dce1669ebe9acada5f9e752835c53e5214e3be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6089
Tested-by: jenkins
The code for oocd_trace has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I989f8345dee4ff2369bcf5e2e2ace86bbd5aa6a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6088
Tested-by: jenkins
The OpenOCD command line flag -p/--pipe was marked as deprecated
in release v0.5.0, more than 9 years ago.
We can reasonably expect that in these 9 years any user of OpenOCD
has already migrated to v0.5.0 or to some newer release, thus has
already updated any local/personal script to get rid of the
deprecated message.
Drop the command line flag already deprecated in v0.5.0.
Change-Id: I2faeb592ed2c2f67c2d3227f118093e39fcf4a8c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6084
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm920t cp15i' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I755c4283e13e125558fcd73b15fe20498eae95ca
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6083
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The command 'arm720t cp15' was marked as deprecated in release
v0.4.0, almost 11 years ago.
We can reasonably expect that in these years any user of OpenOCD
has already migrated to v0.4.0 or to some newer release, thus has
already updated any local/personal script.
There is no run-time warning about the deprecation, but it is
reported in the help and in the documentation.
Drop the command already deprecated in v0.4.0.
Change-Id: I2b325d0312d96ca5e5f0f1bad13bb162b3b75c52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6082
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tarek BOCHKATI
Marc Schink
Matthew Mets
Paul Fertser
Jan Matyas
R. Diez
Antonio Borneo
Evgeniy Didin
Daniel Anselmi
Peter Lawrence
asier70
Yasushi SHOJI