Commit Graph

189 Commits

Author SHA1 Message Date
Antonio Borneo 30f3a2a650 tcl: remove remaining deprecated commands
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...

Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
2021-05-29 21:34:27 +01:00
Antonio Borneo 2a1f3b2574 tcl: fix some minor typo
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
While there, fix one indentation.

Change-Id: I72369ed26f363bacd760b40b8c83dd95e89d28a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6214
Tested-by: jenkins
2021-05-22 10:06:26 +01:00
Andrew Wesie 6448f70e09 tcl/interface/ftdi: Add PLS SPC5 debugger config
Change-Id: I694201db0811beebc94e87822c87fbfc6aecc4c4
Signed-off-by: Andrew Wesie <awesie@gmail.com>
Reviewed-on: http://openocd.zylin.com/6081
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2021-03-20 17:42:06 +00:00
Andrew Wesie 7bc687ade5 tcl/interface/ftdi: Add miniWiggler debugger config
Change-Id: I91f73a377cd9525008d09fda7a7c58d498014b74
Signed-off-by: Andrew Wesie <awesie@gmail.com>
Reviewed-on: http://openocd.zylin.com/6111
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
2021-03-19 21:59:24 +00:00
Antonio Borneo 427552c078 steppenprobe: fix file permission
Commit 895d4a5995 ("tcl/interface/ftdi: Add Steppenprobe open
hardware interface") erroneously set the execution permission to
the configuration file.

Strip the execution permission.

Change-Id: I556451d5e6fee4aee385451e8c90216a25b6ef46
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: http://openocd.zylin.com/5653
Reviewed-on: http://openocd.zylin.com/6038
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Paul Fertser <fercerpav@gmail.com>
2021-01-28 06:01:36 +00:00
Jonathan McDowell 990a01b702 tcl/interface/ftdi: Add HIE JTAG Debugger config
Change-Id: Ibb7a2bb8807c442394982e89258874557a2baaad
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/5910
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-11-07 20:50:57 +00:00
Antonio Borneo 3da7c1fc83 tcl/interface/ti-icdi: remove empty lines at end of file
Change-Id: I031dc52c20b8f213b12df13c9c974d9ac3ef2164
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5603
Tested-by: jenkins
2020-10-30 22:02:46 +00:00
Diego Herranz 895d4a5995 tcl/interface/ftdi: Add Steppenprobe open hardware interface
https://github.com/diegoherranz/steppenprobe

Change-Id: Ief2c3f4a8707fa628650697d93893b2355015898
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/5653
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-10-28 10:13:15 +00:00
John Pham ebb88156ce Added comment to ti-icdi.cfg
Added comment to ti-icdi.cfg specifying how to get serial and an example of
specifying hla_serial for ti-icdi devices. This has been implemented in revision
2121a8f92969804611412b705af8114697a647dc

Change-Id: I648458a4dea176beae6a3f1a4e5641d0206077eb
Signed-off-by: John Pham <jhnphm@gmail.com>
Reviewed-on: http://openocd.zylin.com/2528
Tested-by: jenkins
Reviewed-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-10-24 23:24:45 +01:00
Kevin Burke cbbec2dce5 ARM|Driver: Add DPI Driver for emulation
This driver provides support for Cadence JTAG BFM

The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.

Tested on Ampere emulation with Altra and Altra Max models

Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-10-03 11:21:51 +01:00
Jan Kowalewski 764b25c814 tcl/interface/ftdi: fix comment in minimodule-swd.cfg
Change-Id: I160faca11f231e3e839046ae2045e37e350ca613
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
Reviewed-on: http://openocd.zylin.com/5804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-09-05 16:47:41 +01:00
Antonio Borneo fa9a4d4db5 tcl/interface: snps_sdp: fix minor typo s/similiar/similar/
Change-Id: I4fd6af560278b3e114cc5d8ee1b49b5c4521d8be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: b2821b6074 ("Introduce tcl config files for Synopsys HSDK board")
Reviewed-on: http://openocd.zylin.com/5788
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
2020-08-02 10:49:20 +01:00
Antonio Borneo 33b52174e6 nulink: add minimal support for Nu-Link2
Implementation largely taken from Nuvoton github
	https://github.com/OpenNuvoton/OpenOCD-Nuvoton

Reset is still not fully compatible with OpenOCD framework.
Adapted to hidapi.

Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Reviewed-on: http://openocd.zylin.com/5720
Tested-by: jenkins
Reviewed-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Marc Schink <dev@zapb.de>
2020-08-02 10:48:20 +01:00
Zale Yu b12fca236d jtag/drivers: add support for Nu-Link (Nuvoton ICE) over usb
Add support for Nu-Link1 over usb hidapi and config file.

The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.

Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.

Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
2020-08-02 10:47:02 +01:00
Antonio Borneo 9b32a06dad drivers/linuxgpiod: add led
Bitbang interface allows having a LED on one of the GPIO.

Let also linuxgpiod driver to specify and use the LED connection.

Change-Id: Id3d8772ee1808b92354fd073ba3947bacd8253ef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5770
Tested-by: jenkins
2020-07-26 20:15:34 +01:00
Evgeniy Didin b2821b6074 Introduce tcl config files for Synopsys HSDK board
With this commit we add tcl configure files
for ARCv2 HS Development kit(HSDK). HSDK board
has Quad-core ARC HS38 CPU with L1 and L2
caches.

Change-Id: I372ef45428c7c7ca1421a6da3e5ed08b86f705e0
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5784
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-07-26 20:08:31 +01:00
Antonio Borneo 6962da0028 tcl/interface: add example of linuxgpiod through dln-2
The USB adapter DLN-2 provides 32 GPIO (beside I2C, SPI, ...).
Use the first 6 GPIO for a SWD/JTAG bitbanging example through
linuxgpiod driver.

Change-Id: I229c2078142ec648fc6430b5d123539045dcfbda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5561
Tested-by: jenkins
2020-07-14 00:38:59 +01:00
Antonio Borneo ffe6bc8220 swim: add new transport
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.

Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
2020-05-24 21:32:05 +01:00
Antonio Borneo 6d3cb807aa tcl: fix typo and spelling
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
	find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
	-q --types TYPO_SPELLING --strict -f {} \;

Change-Id: I7b523f0ab5ec047ff167742a44c29984ac672cf4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5615
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
2020-05-09 14:37:35 +01:00
Antonio Borneo 9e23c9ae35 coding style: tcl: remove empty lines at end of text files
Empty lines at end of text files are useless.
Remove them.

Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5171
Tested-by: jenkins
2020-05-02 15:40:12 +01:00
Liming Sun 699a8475a1 jtag/drivers: add debugging support for Mellanox BlueField SoC
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.

Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-04-21 11:18:11 +01:00
Antonio Borneo 9d5767b6b0 coding style: add newline at end of text files
Some text file is missing newline at EOF.
Add it.

Change-Id: Ieebc790096f40961283c644642e56fde975e957f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5167
Tested-by: jenkins
2020-02-24 10:30:53 +00:00
Leonard Crestez 4617630456 tcl/interface/ftdi: Add imx8mp-evk internal JTAG interface
The imx8mp-evk board has a FT4232H chip connected to the chip's JTAG
pins.

Switching between this on-board interface and the external ARM-10
connector is controlled by an GPIO which is behind an i2c expander
connected to the same FTDI chip.

Switching can be performed using the NXP bcu tool:

	https://github.com/NXPmicro/bcu

Change-Id: Ic910515f76eaf09ea6d0f755b026fb09cf09ccfc
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5426
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-02-23 21:32:30 +00:00
Antonio Borneo 095809648b tcl: fix remaining scripts after rework adapter commands
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.

Fix them with the same sed commands used for the other scripts:
	sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
	sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
	sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
	sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)

Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
2020-02-06 21:15:55 +00:00
Andreas Fritiofson b4dc073881 tcl: Add interface config for isodebug isolated JTAG/SWD+UART
Currently only used internally at Unjo.

Change-Id: I7786e95e1bd755a73156ecad5b6d7f6273d8ddef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5251
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
2020-02-06 21:00:44 +00:00
Antonio Borneo 38ac08c1c2 tcl: replace the deprecated commands with "adapter ..."
Avoid annoying "deprecated" messages while running the scripts
distributed with OpenOCD code.
Change automatically created with commands
	sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
	sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
	sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)

Minor indentation issue fixed manually in
	tcl/board/at91sam9g20-ek.cfg
	tcl/target/at91sam9260_ext_RAM_ext_flash.cfg

Change-Id: I425fd56c0c88cd6b06124621306eeb89166dfe71
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5284
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-29 06:34:43 +00:00
Antonio Borneo 2aa2ed1d8a tcl: replace command "interface" with "adapter driver"
Avoid annoying "deprecated" messages while running the scripts
distributed with OpenOCD code.
Change automatically created with command
	sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)

Change-Id: I2291dfb96e164beecbeb3366ce83f9df2ad6c197
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5283
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
2020-01-29 05:36:56 +00:00
Antonio Borneo 944d3e6771 stlink: add DAP direct driver
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.

This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.

Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2020-01-14 11:40:36 +00:00
Al Dyrius 3a50bb46dc Update FTDI C232HM cfg, and add two new cfgs from cable modem research
Change-Id: Idbeffcd5ff4380b1e7c9fd5ef6ba3ca77cc22d99
Signed-off-by: Al Dyrius <aldyrius42@gmail.com>
Reviewed-on: http://openocd.zylin.com/5307
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2019-10-15 09:01:14 +01:00
Antonio Borneo 0bad9a42a3 stlink: add support for STLINK-V3
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.

Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
2018-12-06 13:06:59 +00:00
Antonio Borneo 5d9dad6de1 stlink: add usb pid for v2.1 without mass storage device
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1

Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.

Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2018-12-06 10:02:33 +00:00
Steven Stallion 9e2883b07d interface: adapter configuration for FTDI C232HM
This patch adds support for the C232HM-DDSL-0 and C232HM-EDSL-0
FT232H-based cables from FTDI. For more information, see:
http://www.ftdichip.com/Products/Cables/USBMPSSE.htm

Change-Id: Ic97423eb1e2f6b5ebae04943cd5cce86f38771d5
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4081
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-09-10 09:38:06 +01:00
Edward Fewell 2ba27e2f3e jtag/drivers: Add support for TI XDS110 debug probe
Add support for the XDS110 debug probe using the APIs in the
probe's firmware. Includes support for older versions of the
firmware (with reduced performance) and support for a newer
version that includes OpenOCD specific APIs. Tested on various
TI LauchPads including MSP432P4, MSP432E4, CC2650, CC2652, and
CC3220SF.

Updated to add better support for swd switch. Removed issues found with
clang static analysis.

Updated to add rules entry for the XDS110 probe and Tiva DFU mode (which
affects both XDS110 and ICDI probes).

Change-Id: Ib274143111a68e67e80003797c6a68e3e80976b2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4322
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
2018-05-31 13:25:16 +01:00
Matej Kogovsek ffb93ef371 jtag: drivers: add support for FT232R sync bitbang JTAG interfaces
Change-Id: Ib88a9e270f5c2a50902a137bcc97fdefd5aad1c6
Signed-off-by: Matej Kogovsek <matej@hamradio.si>
Reviewed-on: http://openocd.zylin.com/4215
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-03-13 08:47:46 +00:00
Paul Fertser 7ac798016f tcl: interface: usb blaster I: specify driver explicitly
When a user asks for blaster I, he or she should either get it, or get
an error, not blaster II driver.

Change-Id: Ibc7683676ce42773e2b14ea5ccb3d119d1e6acea
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4381
Tested-by: jenkins
2018-03-13 08:41:43 +00:00
Mateusz Manowiecki 6a4f5a4a67 Add SWD protocol support to buspirate (2nd try)
This is a second try for this patch. I removed the queues from the
previous version. I made it compatible with SRST reset and added
support for those features that could be supported in raw binary
mode.

Change-Id: I96fc06abbea9873e98b414f34afd9043fd9c2a41
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/3960
Tested-by: jenkins
Reviewed-by: Eric Work <work.eric@gmail.com>
Reviewed-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jacob Alexander <haata@kiibohd.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-03-12 14:14:36 +00:00
Robert Jordens fd6986168a pipistrello: decrease jtag speed to 10 MHz
30 MHz is not working reliably here

Change-Id: I38f5f8c7153fc64e313ee911b1629fb5f1114c39
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4242
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-03-07 23:42:01 +00:00
Paul Fertser 5a98ff786e tcl: interface: harmonise RPi configs
Make all configs specify same JTAG and SWD GPIO numbers.

Change-Id: I65b09c1671c97f253f0aab88e511de7409d91e0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3932
Tested-by: jenkins
2018-01-30 07:39:24 +00:00
Patrick Stewart 1003bc7be7 ftdi swd: disable SWD output pin during input
* Disables the data output pin while SWD is reading, so that a simple FTDI
   SWD interface can be made by connecting TCK to SWD_CLK and TDI+TDO directly
   to SWDIO. Enabled by setting SWDIO_OE to 0.

Change-Id: I7d3b71cf3f4eea163cb320aff69ed95d219190bd
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Reviewed-on: http://openocd.zylin.com/2274
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
2018-01-13 11:37:13 +00:00
Robert Jordens 43cf6f9b62 digilent_jtag_smt2_nc: add support
The Digilent SMT2 NC is nominally the connector-less version of the
SMT2. But neither the SMT2 configuration nor the HS3 configuration work
for on the Xilinx KCU105 board where the SMT2 NC is used.

Change-Id: Ieb27cbc6d8b0f9c64ef778e4e0c839acc85ec0ef
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4187
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2018-01-13 09:17:29 +00:00
Paul Fertser 31c58c139d jtag: drivers: stlink: handle all versions with single config
Extend HLA interface to allow multiple VID/PID pairs and use it to
autodetect the connected stlink version.

Change-Id: I35cd895b2260e23cf0e8fcb1fc11a78c2b99c69b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3961
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2017-12-12 21:13:55 +00:00
Jonathan McDowell c0881ba2d5 tcl/interface/ftdi/openrd: Fix FTDI channel + device description
Similar to the Sheevaplug fix inf95f8b70fbd0f7e9c91a2d9006b1abb2dd07ebf2
the OpenRD device has its JTAG interface on the first channel of the
ft2232, which is 0 for the new driver but was 1 for the old one. Correct
the config file appropriately. Also the device description was missing
the trailing " B" and thus not picking up the device correctly. Finally
add an adapter_khz setting in the OpenRD board configuration file - set
to 2MHz to match the Sheeva variant.

Confirmed as working thanks to Phil Hands providing me access to his
hardware to test on.

See also Debian Bug#793214; https://bugs.debian.org/793214

Change-Id: Ifacf53124eaa330bbbdf36dfa79e3256bf2a5201
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4254
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2017-10-27 11:48:05 +01:00
Diego Herranz 5a6f0495db tcl/interface/ftdi: improve minimodule config
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
  TDO and TMS: Safest values given it's an evaluation board
  and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
  which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
  if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
  high impedance (tri-stated).

Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2017-10-03 11:22:56 +01:00
Jonathan McDowell f95f8b70fb tcl/interface/ftdi/sheevaplug: Fix FTDI channel configuration
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.

See also Debian Bug#837989; https://bugs.debian.org/837989

Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
2017-10-03 11:20:18 +01:00
Grzegorz Kostka 83c67b7ac7 imx_gpio: add mmap based jtag interface for IMX processors
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.

Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2017-05-31 08:16:17 +01:00
Forest Crossman f6449a7cba jtag/drivers: Add Cypress KitProg driver
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.

Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2017-05-12 10:08:43 +01:00
Matthias Bock d7d7d8bd40 added interface config file for In-Circuit's ICprog OpenOCD JTAG adapter
Change-Id: I9f9758d3a30bbcca9f750f604e011e5cc25809c5
Signed-off-by: Matthias Bock <mail@matthiasbock.net>
Reviewed-on: http://openocd.zylin.com/4107
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2017-04-23 21:20:17 +01:00
Andreas Fritiofson bcaf775fc1 Remove support for the GPL incompatible FTDI D2XX library
Convert Presto, OpenJTAG and USB-Blaster (I) adapter drivers to libftdi
only.

Change-Id: Ib28887620a3dcbb754b9dbf87b9731acca3ac600
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3237
Tested-by: jenkins
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-11-06 09:47:12 +00:00
Andreas Fritiofson cc2d4f015f Remove since long deprecated ft2232 driver
Purge all legacy interface configurations so there's no more confusion
over which one to use.

Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.

Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
2016-11-06 09:45:06 +00:00
Remco Bloemen 6a3423748b interface: Add XDS100v3 support.
XDS100v3 is software compatible with the XDS100v2, but has a
different usb pid. This commit adds `xds100v3.cfg` that sources
the v2 one and changes the usb pid.

Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80
Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com>
Reviewed-on: http://openocd.zylin.com/3632
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
2016-08-14 02:04:46 +01:00