from pre/post_reset event scripts. Adding the second parameter was
a mistake seen in retrospect. this gives precise control in post_reset
for *when* the post reset speed is set. The pre_reset event was
added *after* the second parameter to jtag_khz/speed
- the target implementations no longer gets involved in the reset mode
scheme. Either they reset a target into a halted mode or not.
target_process_reset()
detects if the reset halt failed or not.
- tcl target event names are now target_N_name. Mainly internal
at this early stage, but best to get the naming right now.
- added hardcoded reset modes from gdb_server.c. I don't know precisely what
these defaults should be or if it should be made configurable. Perhaps some
hardcoded defaults will do for now and it can be made configurable later.
- bugfix in cortex_m3.c for reset_run_and_xxx?
- issue syntax error upon obsolete argument in target command instead of
printing message that will surely drown in the log
git-svn-id: svn://svn.berlios.de/openocd/trunk@849 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This address the >32 bit problem with drscan
also added a check for bypass in the execute since this will manifest itself
as a memory corruption when this check helps to debug the problem alot easier
git-svn-id: svn://svn.berlios.de/openocd/trunk@794 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- drscan is now a low level tcl command:
execute DR scan <device> <num_bits> <value> <num_bits1> <value2>
- removed obsolete partial command text support
git-svn-id: svn://svn.berlios.de/openocd/trunk@791 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- TAP reset without TRST shall be called TLR (stands for test-logic-reset, named after the TAP state it ends is) rather than tms (test-mode-select)
- some comments changed to /* C coding style */
git-svn-id: svn://svn.berlios.de/openocd/trunk@717 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- lower jtag speeds (higher divisor) was used, TDI was not changed on falling TCK edge as it should
- reset signal was release upon any TMS transition, making it impossible to use reset halt
- added khz() and speed_div() functions
git-svn-id: svn://svn.berlios.de/openocd/trunk@716 b42882b7-edfa-0310-969c-e2dbd0fdcd60
And not needed for Windows. Hopefully it will not break a Linux build.
git-svn-id: svn://svn.berlios.de/openocd/trunk@684 b42882b7-edfa-0310-969c-e2dbd0fdcd60
J-Link USB Protocol specification
- added functionality to jlink_init to display the version.
git-svn-id: svn://svn.berlios.de/openocd/trunk@675 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Work in progress to allow launching GDB/telnet server *before* jtag
chain enum, validate & examine
git-svn-id: svn://svn.berlios.de/openocd/trunk@569 b42882b7-edfa-0310-969c-e2dbd0fdcd60
to daemon_startup(still supported).
- print warning if srst and trst change state at the same time when srst_and_trst
is seperate
- reset now performs a trst, examines and validates the jtag chain before targets
assert reset
- if startup fails to examine and validate the jtag chain, try a reset before
trying again
git-svn-id: svn://svn.berlios.de/openocd/trunk@552 b42882b7-edfa-0310-969c-e2dbd0fdcd60
oharboe
ntfreak
mifi