from pre/post_reset event scripts. Adding the second parameter was
a mistake seen in retrospect. this gives precise control in post_reset
for *when* the post reset speed is set. The pre_reset event was
added *after* the second parameter to jtag_khz/speed
- the target implementations no longer gets involved in the reset mode
scheme. Either they reset a target into a halted mode or not.
target_process_reset()
detects if the reset halt failed or not.
- tcl target event names are now target_N_name. Mainly internal
at this early stage, but best to get the naming right now.
- added hardcoded reset modes from gdb_server.c. I don't know precisely what
these defaults should be or if it should be made configurable. Perhaps some
hardcoded defaults will do for now and it can be made configurable later.
- bugfix in cortex_m3.c for reset_run_and_xxx?
- issue syntax error upon obsolete argument in target command instead of
printing message that will surely drown in the log
git-svn-id: svn://svn.berlios.de/openocd/trunk@849 b42882b7-edfa-0310-969c-e2dbd0fdcd60
improve error message in Jim when sourcing a file fails.
Previously it did not tell you the CWD Jim was using as its reference point.
(Helpful when script filenames are a relative path)
git-svn-id: svn://svn.berlios.de/openocd/trunk@840 b42882b7-edfa-0310-969c-e2dbd0fdcd60
within the last 2000ms.
To fix this, add keep_alive() if you are spending >1000ms in an algorithm
thus holding up the server loop.
target_call_timer_callbacks() invokes keep_alive().
2. post_reset script is now executed at normal JTAG speed and not
reset speed.
3. Resume is now synchronous again. Hopefully it will work this time.
git-svn-id: svn://svn.berlios.de/openocd/trunk@826 b42882b7-edfa-0310-969c-e2dbd0fdcd60
associated with the interp structure being passed around
And fixed the message referring to mem2array in the array2mem function
git-svn-id: svn://svn.berlios.de/openocd/trunk@821 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch just uses the command.c interface to create tcl commands for the root level commands and avoids a bit of the "TCL" bleed into the rest of the openocd code.
Multilevel commands also supported.
git-svn-id: svn://svn.berlios.de/openocd/trunk@818 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This evaluates the file at the correct level for the interpreter and the
sets and all the globals are then done as expected.
added a const to find_file function to avoid typecasting
git-svn-id: svn://svn.berlios.de/openocd/trunk@806 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This address the >32 bit problem with drscan
also added a check for bypass in the execute since this will manifest itself
as a memory corruption when this check helps to debug the problem alot easier
git-svn-id: svn://svn.berlios.de/openocd/trunk@794 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- drscan is now a low level tcl command:
execute DR scan <device> <num_bits> <value> <num_bits1> <value2>
- removed obsolete partial command text support
git-svn-id: svn://svn.berlios.de/openocd/trunk@791 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed build warnings for last commit
- set svn props for last commit
git-svn-id: svn://svn.berlios.de/openocd/trunk@760 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Log output handlers now get a "const char *line"
- Added "const" to parameter.
src/helper/command.c
src/helper/command.h
- New function: 'command_output_text()'
- Log output handlers now get a "const char *line"
src/helper/options.c
- Log output handlers now get a "const char *line"
src/server/telnet_server.c
- DO not transmit NULL bytes via TELNET.
- Log output handlers now get a "const char *line"
src/server/gdb_server.c
- Log output handlers now get a "const char *line"
*** THIS INCLUDES PORTIONS OF A PATCH FROM Oyvind sent
previously to the mailing list for TCL users try
src/target/target.c
*** THIS INCLUDES PORTIONS OF A PATCH FROM Oyvind sent
previously to the mailing list for TCL users try
src/target/target.h
*** THIS INCLUDES PORTIONS OF A PATCH FROM Oyvind sent
previously to the mailing list for TCL users try
src/openocd.c
- **MAJOR** Work: New TCL/Jim function: mem2array
- **MAJOR** Work: Redirect Tcl/Jim stdio output to remote users.
- Previously: TCL output did not go to GDB.
- Previously: TCL output did not go to TELNET
- Previously: TCL output only goes to control console.
- This fixes that problem.
+ Created callbacks:
+openocd_jim_fwrite()
+openocd_jim_fread()
+openocd_jim_vfprintf()
+openocd_jim_fflush()
+openocd_jim_fgets()
src/Makefile.am
- New TCL files.
- Future note: This should be more automated. As the list of
'tcl' files grows maintaning this list will suck.
src/Jim.c
- ** THIS INCLUDES A PREVIOUS PATCH I SENT EARLIER **
- that impliments many [format] specifies JIM did not support.
- Jim_FormatString() - **MAJOR** work.
- Previously only supported "%s" "%d" and "%c"
- And what support existed had bugs.
- NEW: *MANY* formating parameters are now supported.
- TODO: The "precision" specifier is not supported.
** NEW ** This patch.
- Jim_StringToWide() test if no conversion occured.
- Jim_StringToIndex() test if no conversion occured.
- Jim_StringToDouble() test if no conversion occured.
** NEW ** This Patch. Major Work.
- Previously output from JIM did not get sent to GDB
- Ditto: Output to Telnet session.
- Above items are now fixed - By introducing callbacks
new function pointers in the "interp" structure.
- Helpers that call the callbacks.
- New function: Jim_fprintf()
- New function: Jim_vfprintf()
- New function: Jim_fwrite()
- New function: Jim_fread()
- New function: Jim_fflush()
- New function: Jim_fgets()
By default: the output is to STDIO as previous.
The "openocd.c" - redirects the output as needed.
- Jim_Panic() - Send panic to both STDERR and the interps
specified STDERR output as a 2nd choice.
- Now JIM's "stdin/stdout/stderr" paramters are "void *"
and are no longer "FILE *".
src/Jim.h
- **MAJOR**
- New JIM STDIO callbacks in the "interp" structure.
- change: "stdin/stdout/stderr" are now "void *" cookies.
- New JIM stdio helper functions.
git-svn-id: svn://svn.berlios.de/openocd/trunk@755 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- DCRDR now used to access special core registers - info is currently omitted from the cortex_m3 TRM ARM have told me this is the preferred access method and the docs will be updated soon.
- now checks for User Thread Mode and Thread mode when halted.
- removed repeated function declarations from command.c
- cortex_m3_prepare_reset_halt removed, updated cortex_m3_assert_reset to suit
git-svn-id: svn://svn.berlios.de/openocd/trunk@558 b42882b7-edfa-0310-969c-e2dbd0fdcd60
for a bit more info before I can tell with confidence whether or not
this would have any effect.
- worked on error propagation and output for flash
git-svn-id: svn://svn.berlios.de/openocd/trunk@539 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- ERROR_FAIL - added to emphasize that information about what went wrong is
contained in Error: log statements and not in a 32 bit return value.
git-svn-id: svn://svn.berlios.de/openocd/trunk@481 b42882b7-edfa-0310-969c-e2dbd0fdcd60
* GDB remote server will now remain online even if the target
is in a funny state, e.g. if it requires a reset, it is
running while GDB is not in the continue or step packet,
e.g. via monitor resume/halt commands in GDB script.
* Added some _DEBUG_GDB_IO_ debug tools
* Fixed a couple of GDB server lockups, e.g. when O packets
detect a severed connection
* added ACK upon connection (send +).
* added keep-alive messages to reset so GDB protocol remains happy.
* fixed crash when timing out connection to GDB
git-svn-id: svn://svn.berlios.de/openocd/trunk@445 b42882b7-edfa-0310-969c-e2dbd0fdcd60
More precise, less code.
- removed unused code in fileio.c
- Windows should now find debug_handler.bin
git-svn-id: svn://svn.berlios.de/openocd/trunk@390 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- open_file_from_path() now uses logging feature
- open_file_from_path() no longer uses paths for anything but "r" mode. Fixes
bug waiting to happen.
git-svn-id: svn://svn.berlios.de/openocd/trunk@389 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix indentation of multi-level commands
- make help command work with multi-level commands
git-svn-id: svn://svn.berlios.de/openocd/trunk@384 b42882b7-edfa-0310-969c-e2dbd0fdcd60
provides a better impeadance match for debug output char fn's, e.g. eCos.
- Line endings are now added at the caller site of command_print*(). command_print()
still adds a line ending
- echo of commands in scripts are now available via debug_level instead of
forced echo
- Added a USER_SAMELINE() for printing without a lineend.
git-svn-id: svn://svn.berlios.de/openocd/trunk@364 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- some more flash cleanup of checking halted state
- moved output handler into options.c
- very slightly tweaked server.c to make it a bit more compatible with eCos
- retired arch_state. Not quite sure how I managed to leave that out last time.
git-svn-id: svn://svn.berlios.de/openocd/trunk@338 b42882b7-edfa-0310-969c-e2dbd0fdcd60
command and reduce confusion with "flash write_image".
- retired deprecated "flash erase" & "flash write".
- added flash_driver_protect/write/erase() that are wafer thin frontend
functions to low level driver functions. They implement checks
that were inconsistently handled by the drivers, e.g. check for
target halted was done in a spotty fashion.
- use return ERROR_COMMAND_SYNTAX_ERROR to print out
syntax of command instead of having lots of inlined replicas of
the command line syntax(some of which were wrong).
- use logging instead of dubious translation of error values to
human understandable explanations of why things failed.
The lower levels log the precise reason and the higher
levels can ammend context as the error propagates up
the call stack.
- simplified flash API slightly with logging instead of
allocating and returning information that the caller then
has to translate into print statements.
git-svn-id: svn://svn.berlios.de/openocd/trunk@337 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added virtual address to working_area.
- Improved error messages in a number of places
- Added ERROR_COMMAND_SYNTAX_ERROR that commands can return to have syntax printed
- Added help for some config commands
- Added verification of sw breakpoints with ERROR() message
- Removed a couple of exit()'s and replaced with error message
- cosmetic fix to armv4_5.c, easier to read
- added polymorphic(with default) virt2phys and mmu enable query function to target.h
- added virt2phys command that uses target->type->virt2phys() fn
Thanks to Øyvind Harboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@310 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Allow all commands to be executed during config stage
- Help now works for config commands
- make var args handling follow the rules more closely
Thanks Øyvind Harboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@305 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Faster DEBUG/INFO() when they are disabled
- target_read/write_buffer() now uses 16 and 32 bit access for single word aligned requests. Other requests are serviced as quickly as possible.
- *much* faster read/write GDB packets, removing timeout problems.
- GDB read/write packets w/single word aligned 32/16 bit access now use 32/16 bit word access.
- working area can now be changed on the fly. Provides a way to move working area about as MMU is enabled/disabled.
- cleaned up error messages for verify_image.
Thanks Øyvind Harboe
git-svn-id: svn://svn.berlios.de/openocd/trunk@302 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- native win32 now handles WSAECONNRESET - no longer exits openocd
- qCRC packet now works correctly under cygwin (gdb compare-sections command)
- removed __USE_GNU define from gdbserver.c
- gdb qSupported packet is now handled, with this we are able to tell gdb packet size, memory map of target
- added new target script gdb_program_config - called before gdb flash programming
- new gdb server command gdb_memory_map (enable|disable> - default is disable
- new gdb server command gdb_flash_program (enable|disable> - default is disable
- gdb flash programming supported - vFlash packets
- image_elf_read_section now does not clear any remaining data, this was causing the gdb checksum to fail with certain files
- reformat of usbprog.c
- memory leak in command_print fixed
- updated texi doc to include new commands
- added gdb programming section to docs
git-svn-id: svn://svn.berlios.de/openocd/trunk@246 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- minor code reformat and cleanup
- updated docs to include new commands
git-svn-id: svn://svn.berlios.de/openocd/trunk@243 b42882b7-edfa-0310-969c-e2dbd0fdcd60
flash verify_image and flash erase_address.
- added patch for new parport_write_on_exit command.
Even this patch will fix some memory leaks.
(thanks too oyvind and Spen for these patches)
git-svn-id: svn://svn.berlios.de/openocd/trunk@240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
config scripts to run sub-config scripts, which was probably the
original intention because "script" is registered as COMMAND_ANY.
This can be useful in e.g. splitting CPU and flash config scripts.
(thanks to oyvind Harboe for the patch)
git-svn-id: svn://svn.berlios.de/openocd/trunk@236 b42882b7-edfa-0310-969c-e2dbd0fdcd60
I have added the clear_malloc and fill_malloc functionality. But the default
is the original malloc.
git-svn-id: svn://svn.berlios.de/openocd/trunk@229 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Reducing stack usage for recursive scripts
- Do not exit on bogus arguments to reset_config. No longer exit the application upon bogus arguments to reset_config, but return errors.
thanks to Øyvind Harboe for these patches.
git-svn-id: svn://svn.berlios.de/openocd/trunk@226 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Obvious fixes to big endian type conversion macros
- Fixed obvious typos for byte masks
git-svn-id: svn://svn.berlios.de/openocd/trunk@217 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- corrected array overrun in armv7m.c
- corrected breakpoint memory allocation bug
- image read now uses fgets, vastly improves reading of large files
- improved hex file reading, support for Linear Address Record added
git-svn-id: svn://svn.berlios.de/openocd/trunk@208 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- add replacements.h to log.h to make sure ERROR is undefined on windows
git-svn-id: svn://svn.berlios.de/openocd/trunk@191 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- make ep93xx and at91rm9200 bitbang JTAG interfaces dependant on ARM host (thanks to Vincent Palatin)
- various whitespace fixes
- removed various warnings
- add support for Debian GNU/kFreeBSD (thanks to Uwe Hermann)
- fix OpenOCD compilation for various platforms (thanks to Uwe Hermann and Vincent Palatin)
- switched order of JTAG chain examination and validation (examine first, then multiple validation tries even if examination failed)
- added target_request subsystem to handle requests from the target (debug messages and tracepoints implemented, future enhancements might include
semihosting, all ARM7/9 only for now)
- added support for GDB vFlashXXX packets (thanks to Pavel Chromy)
- added support for receiving data via ARM7/9 DCC
- reworked flash writing. the 'flash write' command is now deprecated and replaced by 'flash write_binary' (old syntax and behaviour) and 'flash
write_image' (write image files (bin, hex, elf, s19) to a target).
- added support for AMD/ST/SST 29F400B non-cfi flashes
git-svn-id: svn://svn.berlios.de/openocd/trunk@190 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added str9x programming using flash controller tap (str9xpec), including option bytes and device lock/unlock
- inttypes.h now used for long long printf style declarations
git-svn-id: svn://svn.berlios.de/openocd/trunk@174 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed bug in ARM926EJ-S cache handling that caused cache linefills to be disabled after first debug entry
- added support for auto image type detection (thanks to Vincent Palatin)
- further work on ETM trace decoding (tested with a ETB interface using an ETM in normal 16-bit port mode, still experimental)
git-svn-id: svn://svn.berlios.de/openocd/trunk@169 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- reworked etm/etb into a generic etm part with trace capture drivers (currently only etb supported)
- added XScale debug handler binary to repository
- added Thumb disassembling (thanks to Vincent Palatin for this patch)
- added support for non-CFI compatible flashes to cfi driver (currently only SST39VFxxx devices supported)
This checkin is experimental, not suitable for general use
git-svn-id: svn://svn.berlios.de/openocd/trunk@155 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed several uses of uninitialized bits (Thanks to Vincent Palatin for finding and fixing these bugs)
git-svn-id: svn://svn.berlios.de/openocd/trunk@145 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed some compiler warnigns in amt_jtagaccel.c, bitbang.c, parport.c
- free working area and register stuff if str7x block write algorithm failed
- check PC after exiting a target algorithm in armv4_5.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@135 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed compiler warnings throughout the code (thanks to Vincent Palatin for this patch)
- added support for accessing ETB (embedded trace buffer) registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@134 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for reading IHEX files (through fileio)
- load/dump_binary renamed to the more generic load/dump_image <file> <address> ['bin'|'ihex']
- added NAND framework (preliminary)
- added support for the LPC3180 SLC and MLC NAND controllers (preliminary)
- fix initialization for parport
- gw16012 fixes/cleanups
- added EmbeddedICE version 7 (preliminary, reported on two LPC23xx devices so far)
- added 'arm7_9 etm <target#>' configuration command to enable access to the ETM registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@132 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix infinite recursion in target_init_handler (thanks to jw and Magnus Lundin)
- fix CFI flash handlign with buswidth < 32bit (thanks to Daniele Orio for reporting this)
- add support for reading JTAG device id (currently only as debug output on startup)
- cleaned up handling of EmbeddedICE registers. Supported functionality and register size now determined by EmbeddedICE version number.
- small cleanups/fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@124 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for loading .bit files into Xilinx Virtex-II devices
- added support for the Gateworks GW16012 JTAG dongle
- merged CFI fixes from XScale branch
- a few minor fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@116 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- several small fixes
- retry reading from a FT2232 device on incomplete reads
git-svn-id: svn://svn.berlios.de/openocd/trunk@110 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- str75x flash support (Thanks to Spencer Oliver)
- correct reporting of T-Bit in CPSR (Thanks to John Hartman for reporting this)
- core-state (ARM/Thumb) can be switched by modifying CPSR
- fixed bug in gdb_server register handling
- register values > 32-bit should now be supported
- several minor fixes and enhancements
git-svn-id: svn://svn.berlios.de/openocd/trunk@100 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Added state-move support to ftd2xx and bitbang JTAG drivers (required for XScale, possibly useful for other targets, too)
- various fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@78 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fix trunk build for mac os x (patch from Lauri Leukkunen, thanks)
- added check for host endianness, defines WORDS_BIGENDIAN on a big-endian host (e.g. mac os-x)
- fixed bug where endianness of memory accesses could be swapped on BE hosts
- added space for zero termination of ftd2xx_layout string (from Magnus Ludin, tahnks)
git-svn-id: svn://svn.berlios.de/openocd/trunk@73 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- OpenOCD now includes the ability to diassemble instructions on its own (only ARM for now, Thumb might follow).
The command is "armv4_5 disassemble <address> <count> ['thumb']" (thumb is currently unsupported).
I've compared the produced disassembly against GDB/GNU Objdump output, and it seems to be correct, but there may still be some bugs left.
git-svn-id: svn://svn.berlios.de/openocd/trunk@68 b42882b7-edfa-0310-969c-e2dbd0fdcd60
ntfreak
oharboe
mifi
drath
bodylove