Add support for the ARM MCRR/MRRC instructions which require the use of
two registers to transfer a 64-bit co-processor registers. We are going
to use this in a subsequent patch in order to properly dump 64-bit page
table descriptors that exist on ARMv7A with VMSA extensions.
We make use of r0 and r1 to transfer 64-bit quantities to/from DCC.
Change-Id: Ic4975026c1ae4f2853795575ac7701d541248736
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Chalfant <michael.chalfant@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5228
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Lot of messages was logged as LOG_WARNING, but the operation failed
immediately. Sometimes no error message was logged at all.
Add missing messages, change warnings to errors.
Sometimes ERROR_TARGET_INVALID was returned. Some command handlers
returned ERROR_OK! Always return ERROR_TARGET_NOT_HALTED.
While on it use LOG_TARGET_ERROR() whenever possible.
Prefix command_print() message with 'Error:' to get closer
to LOG_TARGET_ERROR() variant.
Error message was not added to get() and set() methods of
struct xxx_reg_type - the return value is properly checked and a message
is logged by the caller in case of ERROR_TARGET_NOT_HALTED.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I2fe4187c6025f0038956ab387edbf3f461c69398
Reviewed-on: https://review.openocd.org/c/openocd/+/7819
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change the prototype of functions:
- target_run_algorithm()
- target_wait_algorithm()
- target_wait_state()
- struct target_type::run_algorithm()
- struct target_type::wait_algorithm()
to use unsigned int for timeout_ms instead of int.
Change accordingly the variables passed as parameter.
Change-Id: I0b8d6e691bb3c749eeb2911dc5a86c38cc0cb65d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7562
Tested-by: jenkins
While there, add a check for target halted and check the number of
parameters accordingly to the command name.
Change-Id: I9e8bb109c35039561997d14782fac682267aee65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7491
Tested-by: jenkins
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Change-Id: Icbe7f7bce287b903edec9dc9db3370722c51fbd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7173
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tcl commands 'arm reg', 'arm mcr/mrc' do not work on M-profile based devices.
Isolate them from 'arm core_state' and 'arm disassemble' and do not chain
them from armv7m_command_handlers.
Change-Id: I2c6befdf82575e95cf05ed158ab5e6faa1a182c3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7101
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Tcl command 'arm core_state' was exposed even on Cortex-M devices.
However it returned message "Unsupported Command" without error status
on such device.
Set the only possible arm->core_state ARM_STATE_THUMB in armv7m init.
Block setting core_state to arm on Cortex-M.
Change-Id: I9525553ac8863a6cf77bbacbcd57e354b6cfe1ca
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7100
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: I3f0879f0f33c6badc36a0dc60229323978a7e280
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6338
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Xiang W <wxjstz@126.com>
In target/arm.h the struct arm do contain 3 flags to retain architecture
version for some tweaks.
The proposal is to have only one enumerated flag 'arch' for the same purpose.
Change-Id: Ia5d5accfed8158ca21eb54af2fdea8e36f0266ae
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6229
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
Commit fc2abe63fd ("armv7m: use generic arm::core_mode") adds
two special modes for ARMv6M and ARMv7M in struct arm_mode_data[].
While these modes do not have any additional register to be dumped
by command 'arm reg', the command still prints an header for these
modes but not followed by any register.
Detect the special modes for ARMv6M and ARMv7M and skip them to
avoid printing the useless header.
Change-Id: I04145769e5742624f143c910eebf9a6f6d8e3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fc2abe63fd ("armv7m: use generic arm::core_mode")
Reviewed-on: http://openocd.zylin.com/5942
Tested-by: jenkins
Commit fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor
mode") introduces the secure mode 28 of ARMv6 as a synonymous of
mode 22 (MON), but does not add it in the switch/case in command
'arm reg'.
When command 'arm reg' scans the array arm_mode_data[] on targets
without secure modes, it does not detect the new secure mode as
not supported by the architecture, thus triggers a segmentation
fault when it try to read the register's value from unallocated
memory.
Issue detected with target arm926ejs.
Add the new mode in the switch/case and treat it as the mode MON.
Change-Id: I2b72cc558e097879a7ee6ea601200bfda6b60270
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: fed7131049 ("armv4_5: support weirdo ARMv6 secure monitor mode")
Reviewed-on: http://openocd.zylin.com/5941
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
There is no method to free the register cache, allocated in
armv4_5, so we get a memory leak.
Issue identified by valgrind.
Implement the method arm_free_reg_cache() and call it in cortex_a
deinit and to exit for error during arm_dpm_setup().
Tested on dual cortex-A stm32mp15x.
This change is inspired from similar fix in commit b01b5fe13a
("armv7m: Fix memory leak in register caching.").
The same allocation is also used by target types "arm7tdmi",
"arm9tdmi", "arm11" and "xscale" but they all lack the deinit
method and I do not have relevant HW to test the fix. For such
reasons they are not addressed in this patch.
Change-Id: I4da1e1f12e36ec245d1f3b11a4eafcbd9a1d2e25
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5693
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Hypervisor mode is present only if the optional virtualization
extensions are available. Moreover, virtualization extensions
require that also security extensions are implemented.
Add the required infrastructure for the shadowed registers in
hypervisor mode.
Make monitor shadowed registers visible in hypervisor mode too.
Make hypervisor shadowed registers visible in hypervisor mode
only.
Check during cortex_a examine if virtualization extensions are
present and then conditionally enable the visibility of both
hypervisor and monitor modes shadowed registers.
Change-Id: I81dbb1ee8baf4c9f1a2226b77c10c8a2a7b34871
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5261
Tested-by: jenkins
The fields core_type and core_mode use the same enum arm_mode
but encode different information, making the code less immediate
to read.
Use a different enum arm_core_type for the field core_type.
The code behavior is not changed.
Change-Id: I60f2095ea6801dfe22f6da81ec295ca71ef90466
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5258
Tested-by: jenkins
Commit 2efb1f14f6 ("Add GDB remote target description support
for ARM4") inserts two additional registers "sp" and "lr" in the
table arm_core_regs[], thus shifting by two the position of the
last three registers already present
"sp_mon" moved from index 37 to 39
"lr_mon" moved from index 38 to 40
"spsr_mon" moved from index 39 to 41
Part of the code is updated (e.g. enum defining ARM_SPSR_MON and
array arm_mon_indices[]), but it's missing the update of mapping
in armv4_5_core_reg_map[].
Fix armv4_5_core_reg_map[].
Change-Id: I0bdf766183392eb738206b876cd9559aacc29fa0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 2efb1f14f6 ("Add GDB remote target description support for ARM4")
Reviewed-on: http://openocd.zylin.com/5257
Tested-by: jenkins
the same semihosting handlers chain is declared twice:
1. in src/target/armv4_5.c
2. in src/target/riscv/riscv.c
to make it simpler we moved the declaration into
'src/target/semihosting_common.c' under semihosting_common_handlers[].
then we used this into both of armv4_5.c and riscv.c
Change-Id: If813b3fd5eb2476658f1308f741c4e805141f617
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5473
Tested-by: jenkins
Reviewed-by: Muhammad Omair Javaid <omair.javaid@linaro.org>
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
During code analysis and development, counting again and again the
lines to find the index of the register is a boring error-prone
brain-damaging activity.
Use the c99 syntax and add once forever the array designators to
specify the index values.
The code behavior is not changed.
Change-Id: I2c70f70794475679efb91a8dfadc00f50715bd3f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5256
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While initializing struct command_registration, the field's name "name"
is not specified, thus relying on the fact that it is the first field
declared in the struct and it's initialization value can be listed as
the first one.
Be coherent in the struct initialization and always use the field's
name.
Change-Id: I9ef7ac08e7cd5b82a6a7896c47017943d668925f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5011
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Fix the write only out params TODO on armv7m.c
Fix conditional move depends on uninitialised value.
It was detected while programming a LPC8Nxx with a FTDI adapter.
valgrind --leak-check=full --show-leak-kinds=all --track-origins=yes
[...]
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E4D3: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E4D3: ftdi_swd_queue_cmd (ftdi.c:1206)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
==8696==
==8696== Conditional jump or move depends on uninitialised value(s)
==8696== at 0x16E506: buf_set_u32 (binarybuffer.h:52)
==8696== by 0x16E506: ftdi_swd_queue_cmd (ftdi.c:1207)
==8696== by 0x18D76D: swd_queue_ap_write (adi_v5_swd.c:271)
==8696== by 0x18E33B: dap_queue_ap_write (arm_adi_v5.h:382)
==8696== by 0x18E33B: mem_ap_write (arm_adi_v5.c:420)
==8696== by 0x197CD9: target_write_buffer_default (target.c:2176)
==8696== by 0x2464B3: armv7m_start_algorithm (armv7m.c:383)
==8696== by 0x246AEB: armv7m_run_algorithm (armv7m.c:330)
==8696== by 0x19D846: target_run_algorithm (target.c:814)
==8696== by 0x1DF3A6: lpc2000_iap_call.isra.3 (lpc2000.c:818)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== Uninitialised value was created by a heap allocation
==8696== at 0x4C2BBAF: malloc (vg_replace_malloc.c:299)
==8696== by 0x220EF9: init_mem_param (algorithm.c:30)
==8696== by 0x1DF247: lpc2000_iap_call.isra.3 (lpc2000.c:777)
==8696== by 0x1E0CF6: lpc2000_erase (lpc2000.c:992)
==8696== by 0x185BDF: flash_driver_erase (core.c:44)
==8696== by 0x18650D: flash_iterate_address_range_inner (core.c:541)
==8696== by 0x18650D: flash_iterate_address_range (core.c:567)
==8696== by 0x18732F: flash_erase_address_range (core.c:584)
==8696== by 0x18732F: flash_write_unlock (core.c:928)
==8696== by 0x18ACDF: handle_flash_write_image_command (tcl.c:457)
==8696== by 0x1B7D99: run_command (command.c:623)
==8696== by 0x1B7D99: script_command_run (command.c:208)
==8696== by 0x1B7FD9: command_unknown (command.c:1033)
==8696== by 0x2E2D37: JimInvokeCommand (jim.c:10364)
==8696== by 0x2E3865: Jim_EvalObj (jim.c:10814)
Change-Id: I50f9a8c4516b686cf62ac3c76f47c53465e949da
Signed-off-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-on: http://openocd.zylin.com/4811
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without this change xxx_start_algorithm() writes all register
parameters no matter of their direction. It usually results
in writing of uninitialized reg_params[].value - possibly
reported by valgrind.
While on it fix the wrong parameter direction in
kinetis_disable_wdog_algo(). This bug did not have any
impact because of unconditional write of reg_params.
Change-Id: Ia9c6a7b37f77d5eb6e5f5463012dddd50471742b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4813
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
All the commands in OpenOCD have been inspected and have the
command mode initialize, apart for two of them.
This is not critical, because the uninitialized value (0) is
equivalent to the enum COMMAND_EXEC, that is also the correct
value for the two mentioned commands.
To keep the code consistent, initialize the command mode to
COMMAND_EXEC.
Change-Id: Iaf043364cbd1005418d787ed045a3ec653612382
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4861
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
GDB can be built for multi-architecture through the command
./configure --enable-targets=all && make
Such multi-architecture GDB requires the target's architecture to
be selected either manually by the user through the GDB command
"set architecture" or automatically by the target description sent
by the remote target (i.e. OpenOCD).
Commit e65acd889c ("gdb_server: add
support for architecture element") already provides the required
infrastructure to support multi-architecture gdb.
arm-none-eabi-gdb 8.2 uses "arm" as default architecture, but also
supports the following values: "arm_any", "armv2", "armv2a",
"armv3", "armv3m", "armv4", "armv4t", "armv5", "armv5t", "armv5te",
"armv5tej", "armv6", "armv6k", "armv6kz", "armv6-m", "armv6s-m",
"armv6t2", "armv7", "armv7e-m", "armv8-a", "armv8-m.base",
"armv8-m.main", "armv8-r", "ep9312", "iwmmxt", "iwmmxt2", "xscale".
These values can be displayed on arm gdb prompt by typing
"set architecture " followed by a TAB for autocompletion.
Set the gdb architecture value for all arm targets to "arm".
Change-Id: I176cb89878606e1febd546ce26543b3e7849500a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4754
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new common semihosting code introduced a bug,
in certain conditions target->semihosting was
used without semihosting being initialised.
The solution was to explicitly test for
target->semihosting before dereferencing it.
Change-Id: I4c83e596140c68fe4ab32e586e51f7e981a40798
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4603
Tested-by: jenkins
Reviewed-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In 2016, ARM released the second edition of the semihosting specs
("Semihosting for AArch32 and AArch64"), adding support for 64-bits.
To ease the reuse of the semihosting logic for other platforms
(like RISC-V), the semihosting code was isolated from the ARM
target and updated to the latest specs.
The new code is already in use since January (in GNU MCU Eclipse
OpenOCD) and no problems were reported, neither for ARM nor for
RISC-V targets, after more than 7K downloads.
The 2 new files were formatted with uncrustify.
Change-Id: Ie84dbd86a547323bb8a5d24eab68fc7dad013d96
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Reviewed-on: http://openocd.zylin.com/4518
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
'flash erase_check' command runs a check algorithm on a target
if possible. The algorithm is run repeatedly for each flash sector.
Unfortunately every start and stop of the algorithm impose not negligible
overhead.
In practice it means checking is faster than plain read only for
sectors of size approx 4 kByte or bigger. And checking sectors
as short as 512 bytes runs approx 4 times slower than plain read.
The patch changes API call target_blank_check_memory() and related
to take an array of sectors (or arbitrary memory blocks).
Changes in target-specific checking routines are kept minimal.
They use only the first block from the array and process it by
the unchanged algorithm.
default_flash_blank_check() routine repeats target_blank_check_memory()
until all blocks are checked, so it works with both multi-block
and single-block based checkers.
Change-Id: I0e6c60f2d71364c9c07c09416b04de9268807f5e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4297
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
This patch adds support in openOCD to read/write Arm vector/floating
point registers. This is compatible with Arm vfp v3 target xml in GDB.
Please refer to binutils-gdb/gdb/features/arm/arm-vfpv3.xml
Change-Id: Id4dd1bddef51c558f1a86300c1a876d159463f18
Signed-off-by: Omair Javaid <omair.javaid@linaro.org>
Reviewed-on: http://openocd.zylin.com/4421
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Tested-by: jenkins
Add "arm semihosting_cmdline [argv0 argv1 ...]" for setting the
command line arguments for the debuggee.
[andreas.fritiofson@gmail.com]: Dynamic allocation, empty default
Change-Id: I831ddd161d602f251940e29608a154e9590fdee1
Signed-off-by: Christian Groessler <chris@groessler.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3106
Tested-by: jenkins
Define a target_addr_t type to support 32-bit and 64-bit addresses at
the same time. Also define matching TARGET_PRI*ADDR format macros as
well as a convenient TARGET_ADDR_FMT.
In targets that are 32-bit (avr32, nds32, arm7/9/11, fm4, xmc1000)
be least invasive by leaving the formatting unchanged apart from the
type;
for generic code adopt TARGET_ADDR_FMT as unified address format.
Don't silently change gdb formatting here, leave that to later.
Add COMMAND_PARSE_ADDRESS() macro to abstract the address type.
Implement it using its own parse_target_addr() function, in the hopes
of catching pointer type mismatches better.
Add '--disable-target64' configure option to revert to previous 32-bit
target address behavior.
Change-Id: I2e91d205862ceb14f94b3e72a7e99ee0373a85d5
Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: David Ung <david.ung.42@gmail.com>
[AF: Default to enabling (Paul Fertser), rename macros, simplify]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
This patch adds support for bridging semihosting to GDB's File-I/O
remote protocol extension. For the most part operations match up 1:1,
however some require a working area to complete successfully, namely
operations that devolve to read, stat, and gettimeofday.
A new command was added to enable support for fileio named `arm
semihosting_fileio`, which ensures that the default behavior remains
intact for those that prefer it.
Finally, redundant logging was removed from the target_arch_state
function; this permits ARM targets to quiesce log output when polling
for a fileio reply. This prevents filling the logs with halt/resume
messages when using semihosting fileio.
Change-Id: Ifbb864fc2373336a501cc0332675b887b552e1ee
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3566
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
struct flash_driver has a default_padded_value field that is similar,
but it can be changed by the user for the specific purpose of padding.
Add a new erased_value field and initialize it for all targets,
particularly stm32lx, xmc4xxx and virtual.
Use this value in core.c:default_flash_mem_blank_check(), the slow path.
Extend the target API to pass erased_value down to target code.
Adding an argument ensures that we catch all callers.
This allows us to merge xmc4xxx.c:xmc4xxx_blank_check_memory() into
armv7m:armv7m_blank_check_memory().
It further allows us to use default_flash_blank_check() in place of
xmc4xxx.c:xmc4xxx_flash_blank_check(), adding a potential slow path
fallback, as well as stm32lx:stm32lx_erase_check(), adding the potential
armv7m fast path with fallback to default_flash_mem_blank_check().
Fix a mips32 code comment while at it (zeroed -> erased).
The armv4_5 and mips32 target implementations will now error out if an
erase value other than 0xff is used, causing default_flash_blank_check()
to fall back to the default_flank_mem_blank_check() slow path.
Change-Id: I39323fbbc4b71c256cd567e439896d0245d4745f
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3497
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add rules to build armv4_5_crc.inc, and convert the code to target
endianness the least intrusive way.
Change-Id: I7452b2c7e679dae14f9cda5f89bc81c16fc12cad
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3473
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Add rules to build armv4_5_erase_check.inc, and convert the code to
target endianness the least intrusive way.
Drop an unused word from the assembler sources to make the ARM bytecode
fully match that of armv4_5.c and to not break ARMv4 assumptions.
This completes the build rules for contrib/loaders/erase_check directory.
Change-Id: I36be7a944e26142088195fa3fb072d4e577bf328
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3135
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: Ie3f95f992a98a1325428e4032a1c17346d4c9977
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3472
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Clean up the working area in case writing fails.
Change the error handling paradigm to avoid duplication.
Change-Id: I95bb12fbe7c80b594e178468bcd4f6387c682c93
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3471
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
On the ARM PB1176JZF-S the system comes up in secure monitor
mode after reset. However the modebits in CPSR form the value
28 (0x1c) and CPSR is 0x800001dc deeming it UNRECOGNIZED.
Define this mode to be synonymous to mode 22 (MON) and things
start to work like a charm.
Change-Id: I001f7773ee1076202c0c633e466d2d833f7a1413
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-on: http://openocd.zylin.com/3196
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch adds the fpv4-sp-d16 registers to the armv7m register set.
The work is inspired by Mathias K but takes a different approach:
instead of having both double and single presicion registers in the
cache this patch works only with the doubles and counts on GDB to
split the data in halves whenever needed.
Tested with HLA only (on an STM32F334 disco board).
Currently this patch makes all ARMv7-M targets report an FPU-enabled
target description to GDB. It shouldn't harm if the user is not trying
to access non-existing FPU. However, the plan is to make this depend
on actual FPU presence later.
Change-Id: Ifcc72c80ef745230c42e4dc3995f792753fc4e7a
Signed-off-by: Mathias K <kesmtp@freenet.de>
[fercerpav@gmail.com: rework to fit target description framework]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/514
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Also remove an unrelated no-op cast.
Change-Id: Ibeb6c72e5b0b0347abb568947a05a179661faf2d
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2473
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Florian Fainelli
Tomas Vanek
Antonio Borneo
Erhan Kurubas
Marc Schink
Tarek BOCHKATI
Marc Schink
Jean-Christian de Rivaz
Liviu Ionescu
Omair Javaid
Andreas Fritiofson
Dongxue Zhang
Steven Stallion
Andreas Färber
Linus Walleij
Paul Fertser