flash programming via flash write_image or gdb load would
produce a bogus error message that the flash chip was to
small.
The solution is to limit the current flash programming
run to the current chip.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
SMI interface hides the real SPI bus between SPEAr and
external flash.
Added comments to highlight the SPI operation, to help a
future rework in SPI generic and SPEAr specific drivers.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
this never panned out and there are enough mistakes in
the code that probably nobody used this.
Use the tcl server and implement a standalone http
app instead works fine.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add comments to assembly flash loader for STM32. Add tiny improvement in
size of the algorithm (40 vs 48 bytes) and tiny speed improvement (~1.5%,
as time is wasted on waiting for end of operation anyway).
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
gdb connect can fail when the flash has not been probed.
During gdb connect, the flash layout is reported, but this
can not be automatically detected for a target that is
powered up and OpenOCD supports connecting to gdb server
even if the target is powered down.
The solution is to turn of the gdb_memory_map feature.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
If the CPU crashed at some point, poll will discover this.
Previously the poll fn would clear the error and print a warning,
rather than propagating the error.
The new behavior is to report the error back up, but still
clear the error.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Document "-n" option in manual;
Modify "echo" command definition as COMMAND_HANDLER to
easily add help message
Add help message aligned with manual.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
With the new JIMTCL, "puts" only writes to stdout.
To write on telnet port too, "echo" must be used.
This patch gives to "echo" similar commandline option of "puts".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
add missing error handling.
Output warning when assuming maximum flash size in the
family when failing to read.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Implement autodetection of debug base. Also, implement a function solving
various hardware quirks (like iMX51 ROM Table location bug).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch implements "dap_lookup_cs_component()", which allows to lookup CS
component by it's identification.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch adds function called "dap_detect_debug_base()", which should be
called to get location of the ROM Table. By walking ROM Table, it's possible to
discover the location of DAP.
Sadly, some CPUs misreport this value, therefore I had to introduce an fixup
table, which will be used in case such CPU is detected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
So far most of the people have been using existing ARM966E in the
place of ARM946E, because they have practically the same scan chains.
However, ARM946E has caches, which further complicates JATG handling
via scan-chain. this was preventing single-stepping for ARM946E when
SW breakpoints are used.
This patch thus introduces :
1) Correct cache handling on memory write
2) Possibility to flush whole cache and turn it off during debug, or
just to flush affected lines (faster and better)
3) Correct SW breakpoint handling and correct single-stepping
4) Corrects the bug on CP15 read and write, so CP15 values
are now correctly R/W
help would not show help for commands when the command
interpreter was in the wrong mode, which means that
e.g. "help newtap" didn't work, it wouldn't show the
"jtag newtap" help as it was a configuration command.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Collect variable definitions.
Report syntax error to command dispatcher.
Propagate error when unable to open file.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
When usng gdb pipes we need to keep openocd output at a minimum,
otherwise the gdb stdin will overflow and fail.
Make the calls to gdb_port and log_output synchronous to stop this.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
commit 50d5441e2a caused
native windows build to fail.
Firstly this patch fixes the build issue, but it also disables support
for named pipes under Windows. Windows does not support posix named
pipes.
A cross-platfom access layer will need creating before support can be
enabled again.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
there was special support to support pressing 'x' to quit
openocd. ctrl-c is sufficient. The main server loop is already
complicated enough.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
There is an explicit command "log_output" that can
be used to redirect log output to a file, no need
for a hack in the first place.
Before enabling pipes, use "log_output foo" to redirect
log output to the "foo" files.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
ep93xx and at91rm9200 are conditionally built only on arm and were not
updated to reflect changes in command registration handler.
This patch makes them properly compile again, fixing a build failure
experienced on Debian armel.
Signed-off-by: Luca Bruno <lucab@debian.org>
Signed-off-by: Zachary T Welch <zwelch@codesourcery.com>
short story: if the JTAG clock is too high, then the
behavior will be flaky and kludging the code may
seem to make things beter, but really it's just a red
herring.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
capture of progress output would get polling
results. This will break in the example below
where polling output would override the tcl
return value.
capture {sleep 10000; set abc def}
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by using ctrl-z instead of line end, multi-line tcl scripts
can be handled.
Testing: send ctrl-z a couple of times to make telnet enter the
mode where it sends ctrl-z unencoded.
Programs that talk to the tcl_server can send ctrl-z to
indicate end of tcl-let to be executed without having
to worry about telnet protocols.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
with this buffering disabled fancier logging scripts will
be able to process each line as it is output.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
used /dev/mem and mmem() to memory map JTAG registers
into user space and used new configure options to exclude
eCos specific code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
A while back I sent in a patch that adds support for watchpoint lengths greater
than four on xscale. It's been working well, until the other day, when it
caused an unexpected debug exception. Looking into this I realized there is a
case where it breaks: when the length arg is greater than the base address.
This is a consequence of the way the hardware works. Don't see a work-around,
so I added code to xscale_add_watchpoint() to check for and disallow this
combination.
Some more detail... xscale watchpoint hardware does not support a length
directly. Instead, a mask value can be specified (not to be confused with the
optional mask arg to the wp command, which xscale does not support). Any bits
set in the mask are ignored when the watchpoint hardware compares the access
address to the watchpoint address. So as long as the length is a power of two,
setting the mask to length-1 effectively specifies the length. Or so I thought,
until I realized that if the length exceeds the base address, *all* bits of the
base address are ignored by the comaparator, and the watchpoint range
effectively becomes 0 .. length.
Questions, comments, criticisms gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Hi everyone,
Added more LOG_ERROR messsages to watchpoint and breakpoint code, given that the
infrastructure no longer interprets returned error codes. Also changed
existing LOG_INFO and LOG_WARNING to LOG_ERROR for cases where an error is
returned.
Note that the check of the target state is superflous, since the infrastruture
code currently checks this before calling target code. Is this being
reconsidered as well? Also, should we stop returning anything other than
ERROR_OK and ERROR_FAIL?
Comments gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
do not try to interpret "retval" into a string, just
amend a bit about the context of the already reported
error.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
Version 2 of this patch. Code added to breakpoints.c was removed from previous
patch, and item 3 added, per discussion with Øyvind regarding error reporting.
Item 4 added, which I just noticed.
I tried to use a software breakpoint in thumb code on the xscale for the first
time recently, and was surprised to find that it didn't work. The result was
this patch, which does four things:
1): fix trivial cut-n-paste error that caused thumb breakpoints to not work
2): call xscale_set_breakpoint() from xscale_add_breakpoint()
3): log error on data abort in xscale_write_memory()
4): fixed incorrect error code returned by xscale_set_breakpoint() when no
breakpoint register is available; added comment
Item 2 not only makes the xscale breakpoint code consistent with other targets,
but also alerts the user immediately if an error occurs when writing the
breakpoint instruction to target memory (previously, xscale_set_breakpoint() was
not called until execution resumed). Also, calling xscale_breakpoint_set() as
part of the call chain starting with handle_bp_command() and propagating the
return status back up the chain avoids the situation where OpenOCD "thinks" the
breakpoint is set when in reality an error ocurred.
Item 3 provides a helpful message for a common reason for failure to set sw
breakpoint.
This was thoroughly tested, mindful of the fact that breakpoint management is
somewhat dicey during single-stepping.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
I figured since I was poking around in the breakpoint code on other arches, I'd
add this change to those arches that don't do it already. This patch propagates
the return code of <arch>_set_breakpoint() up the call stack. This ensures that
the higher layer breakpoint infrastructure is aware that an error ocurred, in
which case the breakpoint is not recorded.
Normally I wouldn't touch code that I can't test, but the code is very
uniform across architectures, and the change is rather benign, so I figured
after careful inspection that it is safe. If the maintainers or others think
this is imprudent, the patch can be dropped.
Also changed the error code to something more appropriate in two cases where
hardware resources are unavailable.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
you can now set a variable in a script like set version [version].
Also version takes an optional argument "git" to show git version
of source. If git is not installed during the build, then this
will yield an error that is ignored during the build and "version git"
returns an empty string.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Commands that output progress output and no return value
will have the progress output captured.
Commands that do not output progress output(tcl commands)
will return the tcl return value instead.
The advantage here is that it is no longer necessary to
consider which command one is capturing, it works for
either.
Example #1: capture progress output:
set foo [capture help]
Example #2: capture tcl return value
set foo [capture {set abc def}]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
for non_cfi cfi chips free() was invoked on rodata.
The mystery is why this bug has survived for so long.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
sizeof() is a bit less scary than seing assumption
about size of type, no bug as such.
Use NULL instead of 0 for pointers. More obvious that
it is a pointer from code inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
This simple patch fixes a problem I noticed on the xscale where incorrect values
are sometimes reported by the reg command. The problem can occur when
requesting the value of registers in the xscale-specific register cache. With a
couple of exceptions, none of the registers in the xscale register cache are
automatically retrieved on debug entry. This is probably fine, as they are
unlikely to be needed on a regular basis during a typical debug session, and
they can be retrieved when explicitly requested by name using the reg command.
The problem is that once this is done, the register remains marked as valid for
the remainder of the OpenOCD session, and the reg command will henceforth always
report the same value because it is obtained from the cache and is never again
retrieved from the debug handler on the target.
The fix is to mark all registers in the xscale register cache as invalid on
debug entry (before the two exceptions are retrieved), thus forcing retrieval
(when requested) from the target across resumptions in execution, and avoiding
the reporting of stale values.
Small addition change by Øyvind: change 'i' to unsigned to fix compiler
warning for xscale_debug_entry() fn.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I a mail conversation with Øyvind we stated that speed may not be set at
all on case CLOCK_MODE_KHZ and CLOCK_MODE_RCLK. Also there isn't proper
error propagation adapter_khz_to_speed or jtag_rclk_to_speed.
So jtag_get_speed may need some rewrite for error propagation.
CC: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Do not fail startup if communication with target is
not possible.
OpenOCD supports launching without a target connected
or the target powered down.
The user will typically power up the target and issue
a "reset init" + load his application after OpenOCD
is started then.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
This new cmd adds the ability to choose the Cortex-M3
reset method used.
It defaults to using SRST for reset if available otherwise
it falls back to using NVIC VECTRESET. This is known to work
on all cores.
Move any luminary specific reset handling to the stellaris cfg file.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
bitq.c: In function ‘bitq_scan_field’:
bitq.c:224: error: declaration of ‘pause’ shadows a global declaration
/usr/include/unistd.h:429: error: shadowed declaration is here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
committed so as to ease cooperation and to let it be improved
over time.
So far it supports:
- halt/resume
- registers inspection
- memory inspection/modification
I'm still getting up to speed with OpenOCD internals and AVR32 so code is a little
bit messy and I'd appreciate any feedback.
if a tap could not be _enabled_, the error message was
'failed to disable tap'. Fixed that. Also, display the failing
tap's name.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
The patch improves flash erase for STR9x in case of a full bank erase.
Then the chip erase command is used instead which improves speed significantly.
Also I think it might help if e.g. STR912 enters some state where flash banks are locked, and a chip erase command is the key for unlocking the flash.
ocd_ prefix is used internally in OpenOCD as a kludge more
or less to deal with the two kinds of commands that OpenOCD
has.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
if polling is off, then "reset run + halt" would fail
since halt incorrectly assumed the target was in the
reset state as it is the internal poll implementation
that moves the sw tracking of the target state out
of the reset state.
To reproduce:
> reset run; halt
JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1)
BUG: arm7/9 does not support halt during reset. This is handled in arm7_9_assert_reset()
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
back-off algorithm for polling. Double polling
interval up to 5000ms when it fails.
when polling succeeds, reset backoff.
This avoids flooding logs(as much) when working
with conditions where the target polling will fail.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
It is useful to know that the printed errors are *all* the
errors there were.
Added missing error handling(found by inspection).
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
it can be useful to throttle performance: test
differences in behavior, test performance effect
of long roundtrips.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This flash driver works on more than just two chips.
(Though it does need work still, e.g. to protect more than 64K.
(On non-'3748-A0 chips where errata allow that.))
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make it scriptable, so code can be conditionalized based on
what transport is in use for the session.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
For the above targets the exit_point is
optional when used with run_algorithm, so remove it.
This makes updating the algorithm less error prone.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the mips32 uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As the armv7m uses instruction breakpoints for algorithms we do not really
need to check the pc on exit.
This now matches the behaviour of the arm4_5 codebase.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Update the arm_checksum_memory and arm_blank_check_memory
algorithms to use a breakpoint instruction on v5 arch.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Set up more of the Luminary-specific signals, and stop cloning
a few of the JTAG defaults. More comments too.
Still leaves the "dap info 0" bugs unresolved (presumably coupled
to this particular adapter family) where TPIU, ITM, DWT, and other
debug modules wrongly display as extra NVICs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Provide $defines for more of the signals involved in the
Luminary ICDI hardware, and comment some of what's going on.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use addition for offsetting, not masking. Shorten some lines.
Make "component_start" print-only (unused otherwise; don't save).
Still doesn't resolve the issue where multiple components
are wrongly displaying as NVICs on some Cortex-M3 parts because
many PIDs appear to be zeroes ... maybe adapter related??
Signed-off-by: David Brownell <db@helium.(none)>
waiting for ZY1000 fifo to idle is now queued as
an asynchronous command. This radically improves
performance when waitIdle() is interspersed with
writes as no readback is required over TCP/IP.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Mask the upper bits after 32-bit reads.
Alsoo revert the ugly changes to use PRIx32; just cast to unsized
integers when printing (two chars not eight).
Signed-off-by: David Brownell <db@helium.(none)>
This reverts the incorrect change made to the arm9 cmd group in commit
d1eca9a74c.
The code now matches the docs and the release notes.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
* Bugfix and simplify legacy jtag-only defaulting
* Make "dummy" declare its jtag-only nature
* likewise update ft2232
* warn if selection is _required_ (multi-transport adapters),
fixes the "only ft2232 works" bug for at least dummy, with
other drivers going the "legacy" path (submit patches).
Signed-off-by: David Brownell <db@helium.(none)>
String compare against addresses in range 0 or so due
to not checking if there was an active session first.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Classic manifestation of weakness of dangling {
formatting :-) Hard to spot these sort of mistakes visually.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Commit 93f2afa45f dropped the sentinel off the end
of the command_registrants[] array. The loop immediately
following the initialization will walk right off the end.
Signed-off-by: Stacey Sheldon <stac@solidgoldbomb.org>
This adds the guts of a transport framework with initialization,
which should work with current JTAG-only configurations (tested
with FT2232).
Each debug adapter can declare the transports it supports, and
exactly one transport is initialized. (with its commands) in
any given OpenOCD session.
* Define a new "struct transport with init hooks and a few
"transport" subcommands to support it:
"list" ... list the transports configured (just "jtag" for now)
"select" ... makes the debug session use that transport
"init" ... initializes the selected transport (internal)
* "interface_transports" ... declares transports the current interface
can support. (Some will do this from C code instead, when there are
no hardware versioning (or other) issues to prevent it.
Plus some FT2232 tweaks, including a few to streamline upcoming
support for an SWD transport (initially for Luminary adapters).
Eventually src/jtag should probably become src/transport, moving
jtag-specific stuff to transport/jtag.
Signed-off-by: David Brownell <db@helium.(none)>
Revert change made in commit dd88b461da.
Caused segfaults when using ftdi driver under win32.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The code did not transfer the last word in no-ack transfers.
The strange thing is that this did not lead to any
observable errors.
This gaffe was introduced in commit 1f5883ea56
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Review allocation of error numbers in openocd
to avoid overlap.
Put brackets around negative numbers to avoid
issues during macro expansion.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Memory read/writes to virtual memory, requires that the CPU is
halted.
Use 'phys' option to write to memory while target is running.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when locking the debug access fails on the first try, it's a
bit noisy, so print out message that it succeeded on second try.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add "static" qualifier to private functions.
Move duplicated global declarations from "target/avrt.c"
and "nor/avrf.c" to "target/avrt.h".
Remove unused declarations form "nor/avrf.c".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Add "static" qualifier to private functions.
Remove private prototypes from include file.
Remove empty definition of JIM_STATIC.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This fn is an implementation detail of jtag_execute_queue()
that is not to be exposed externally.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
normal code should not call jtag_get_error(), but rather check
the return code from jtag_execute_queue().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
When an interactive command fails, the Jim stack trace prints references to
the line in "command.c" where the interpreter was invoked. Since that
location has no relation to the actual command that failed, the information
serves only to add confusion.
By not adding the useless source info to Jim the noise can be reduced,
while still printing a useful trace for nested commands.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add "static" qualifier to private functions.
Function Jim_InterpolateTokens() is private, but has not
been changed to "static".
This function is called only once, so compiler inlines it.
After inline, there is a warning for variable uninitialized.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
(error: declaration of ‘stat’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/sys/stat.h:279: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
(error: declaration of ‘byte’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:50: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
(error: declaration of ‘pHDev’ shadows a global declaration; ../../../../src/jtag/drivers/rlink.c:102: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
in jim.c (error: declaration of ‘boolean’ shadows a global declaration; /usr/local/lib/gcc/i686-w64-mingw32/4.4.2/../../../../i686-w64-mingw32/include/rpcndr.h:52: error: shadowed declaration is here)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
copy & paste error + added FIFO throttling to work around
lockup bug in FPGA.
The arm11 optimisation was introduced post v0.4.0, so this
is not a regression compared to previous release.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Helper ./src/helper/membuf.c is only used in at91sam3.c
1) Replace membuf with LOG_*
2) The original code in sam3_GetDetails() invalidates
all the buffered output of sam3_GetInfo(). The new
code skips sam3_GetInfo() if its output should not
be printed.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I think this fixed an error message where the error
message would show the *previous* uc code rather than
the current unsupported uc code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
when the verify failed, it didn't return an error,
which breaks e.g. tcl scripts that rely on this for
exceptions to work.
Found by -Wshadow
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
this batch of fixes should be pretty straightforward
rename of 'index' and an 'i' local variable shadowing.
'index' conflicts with a global name.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Antonio Borneo
Øyvind Harboe
Freddie Chopin
Marek Vasut
ddraskovic
Spencer Oliver
Peter Stuge
Michal Demin
David Brownell
Luca Bruno
Mike Dunn
Flemming Futtrup
Alexander Stein
Wookey
Oleksandr Tymoshenko
Catalin Patulea
Piotr Esden-Tempski
Thomas Koeller
Fredrik Hederstierna
Michal Demin
sb-sf
Stacey Sheldon
Marc Pignat
Olaf Lüke
Edgar Grimberg
Andreas Fritiofson