Change the handling of the "-ircapture" and "-irmask" parameters
to be slightly more sensible, given that the JTAG spec describes
what is required, and that we already require that conformance in
one place. IR scan returns some bitstring with LSBs "01".
- First, provide and use default values that satisfy the IEEE spec.
Existing TAP configs will override the defaults, but those parms
are no longer required.
- Second, warn if any TAP gets set up to violate the JTAG spec.
It's likely a bug, but maybe not; else this should be an error.
Improve the related diagnostics to say which TAP is affected.
And associated minor fixes/cleanups to comments and diagnostics.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2758 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Ready for discussion and tiny patches that tries out this scheme.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2755 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Added gdb_sync feature that allows GDB to sync up to target state.
Issue "monitor gdb_sync" and the next stepi, will return immediately
with updated register values to GDB.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2754 b42882b7-edfa-0310-969c-e2dbd0fdcd60
make sure that when there are two or more targets, their
various pre/post event reports are correctly ordered.
Previously, only the first target always saw its "pre"
method before SRST was asserted or deasserted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2753 b42882b7-edfa-0310-969c-e2dbd0fdcd60
only expose the registers which are actually present. They
could be missing for two basic reasons:
- This version might not support them at all; e.g. ETMv1.1
doesn't have some control/status registers. (My sample of
ARM9 boards shows all with ETMv1.3 support, FWIW.)
- The configuration on this chip may not populate as many
registers as possible; e.g. only two data value comparators
instead of eight.
Includes a bugfix in the "etm info" command: only one of the
two registers is missing on older silicon, so show the first
one before bailing.
Update ETM usage docs to explain that those registers need to be
written to configure what is traced, and that some ETM configs
are not yet handled. Also, give some examples of the kinds of
constrained trace which could be arranged.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2752 b42882b7-edfa-0310-969c-e2dbd0fdcd60
system, removes 20 non-existent registers ... but still includes
over 45 (!) ETM registers which don't even exist there ...
- Integrate the various tables to get one struct per register
- Get rid of needless per-register dynamic allocation
- Double check list of registers:
* Remove sixteen (!) non-registers for data comparators
* Remove four registers that imply newer ETM than we support
* Change some names to match current architecture specs
- Handle more register info
* some are write-only
* some are read-only
* record which versions have them, just in case
- Reorganize the registers to facilitate removing the extras
* group e.g. comparator/counter #N registers together
* add and use lookup-by-ID
git-svn-id: svn://svn.berlios.de/openocd/trunk@2751 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Add a header comment
- Line up the ETM context struct, pack it a bit
- Remove unused context_id (this doesn't support ETMv2 yet)
- Make most functions static
- Remove unused string table and other needless lines of code
- Correct "tracemode" helptext
Also provide and use an etm_reg_lookup() to find entries in the ETM
register cache. This will help cope with corrected contents of that
cache, which doesn't include entires for non-existent registers.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2750 b42882b7-edfa-0310-969c-e2dbd0fdcd60
didn't turn up earlier. Is everyone still using gcc 3.x? Or is the x86
version of gcc 4.x much more relaxed?
git-svn-id: svn://svn.berlios.de/openocd/trunk@2749 b42882b7-edfa-0310-969c-e2dbd0fdcd60
of a (NOR) flash chip: allow passing "last" as an alias
for the number of the last sector.
Improve several aspects of error checking while we're at it.
From: Johnny Halfmoon <jhalfmoon@milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2746 b42882b7-edfa-0310-969c-e2dbd0fdcd60
garbage after the expected data (from the TAPs' BYPASS or IDCODE
registers).
NOTE that there was previously some code that looked like it was
trying to do this ... which didn't work, because it was looping
over the list of expected TAPs, and never checked *after* that
list completed! That could hide some *nasty* reset issues...
Also replace a now-obsolete scanchain length test with one that
behaves correctly; and update reporting of unexpected IDCODEs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2739 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch modifies an error message which, in its original state,
I find somewhat unhelpful. So a small hint was added.
Signed-off-by: Johnny Halfmoon <jhalfmoon at milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2738 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Shrink messaging during resets, primarily by getting rid of
"nothing happened" noise that hides *useful* information.
- Improve: the "no IDCODE" message by identifying which tap only
supports BYPASS; and the TAP event strings.
Related minor code updates:
- Remove two needless tests when examining the chain: we know
we have a TAP, and that all TAPs have names.
- Clean up two loops, turning "while"s into "for"s which better
show what's actually being done.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2736 b42882b7-edfa-0310-969c-e2dbd0fdcd60
for disabling TAPs. We don't actually know how to make any
JRCs which do that yet; but when we do, this will matter.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2735 b42882b7-edfa-0310-969c-e2dbd0fdcd60
and Tcl/external):
- Reorder so *both* paths (TCK/TMS or TRST) can enable TAPs with
ICEpick ... first C code flags TAPs that got disabled, then call
any Tcl code that might want to re-enable them.
- Always call the C/internal handlers when JTAG operations can be
issued; previously that wasn't done when TRST was used.
Plus some small cleanups (whitespace, strings, better messaging
during debug and on some errors) to reset-related code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2730 b42882b7-edfa-0310-969c-e2dbd0fdcd60
avoid a duplicate test.
Plus other cleanup in the same code: be "static", sane line lengths
for source and diagnostics, and fix misleading variable names.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2725 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Erase logic:
- command invocation
+ treat "nand erase N" (no offset/length) as "erase whole chip N"
+ catch a few more bogus parameter cases, like length == 0 (sigh)
- nand_erase() should be static
- on error
+ say which block failed, and if it was a bad block
+ don't give up after the first error; try to erase the rest
- on success, say which nand device was erased (name isn't unique)
Device list ("nand list"):
- say how many blocks there are
- split summary into two lines
- give example in the docs
Doc tweaks:
- Use @option{...} for DaVinci's supported hardware ECC options
For the record, I've observed that _sometimes_ erasing bad blocks causes
failure reports, and that manufacturer bad block markers aren't always
erasable (even when erasing their blocks doesn't trigger an error report).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2724 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- update comments to say so.
- update docs to clarify that the "arm9tdmi" command prefix
is a misnomer.
- bugfix some messages that wrongly assume only ARM9TDMI
based processors use this code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2719 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Cleanup some the downloaded ARM target algorithm code:
- Provide more complete disassembly of the DCC bulk write code
- Make code blocks "static const", in case GCC doesn't
- Fix some tabbing/layout issues
- Make some arm7_9_common.h flags be "bool" not "int"; and compact
the layout a bit (group most bools together)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2698 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch adds target algorithm support for those flash devices that do not support DQ5 polling. So far they could only be programmed with host algorithm, but this was way too slow.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2682 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Infinite loop bugfix when running tap configure a second time
git-svn-id: svn://svn.berlios.de/openocd/trunk@2681 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Optionally shave time off the armv4_5 run_algorithm() code: let
them terminate using software breakpoints, avoiding roundtrips
to manage hardware ones.
Enable this by using BKPT to terminate execution instead of "branch
to here" loops. Then pass zero as the exit address, except when
running on an ARMv4 core. ARM7TDMI, ARM9TDMI, and derived cores
now set a flag saying they're ARMv4.
Use that mechanism in arm_nandwrite(), for about 3% speedup on a
DaVinci ARM926 core; not huge, but it helps. Some other algorithms
could use this too (mostly flavors of flash operation).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2680 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Provide an "armv7a disassemble" command. Current omissions include
VFP (except as coprocessor instructions), Neon, and various Thumb2
opcodes that are not available in ARMv7-M processors.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2676 b42882b7-edfa-0310-969c-e2dbd0fdcd60
lean up some loose ends with the ARM disassembler
- Add a header comment describing its current state and uses
and referencing the now-generally-available V7 arch spec
- Support some mode switch instructions:
* Thumb to Jazelle (BXJ)
* Thumb to ThumbEE (ENTERX)
* ThumbEE to Thumb (LEAVEX)
- Improve that recent warning fix (and associated whitespace goof)
- Declare the rest of the internal code and data "static". A
compiler may use this, and it helps clarify the scope of these
routines (e.g. what changes to them could affect).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2675 b42882b7-edfa-0310-969c-e2dbd0fdcd60
By enabling this bit, the processor halts when a debug event
such as breakpoint occurs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2668 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Abstract the orion_nand_fast_block_write() routine into a separate
routine -- arm_nandwrite() -- so that other ARM cores can reuse it.
Have davinci_nand do so. This faster than byte-at-a-time ops by a
factor of three (!), even given the slowish interactions to support
hardware ECC (1-bit flavor in that test) each 512 bytes; those could
be read more efficiently by on-chip code.
NOTE that until there's a generic "ARM algorithm" structure, this
can't work on newer ARMv6 (like ARM1136) or ARMv7A (like Cortex-A8)
cores, though the downloaded code itself would work just fine there.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2663 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Via code review by Steve Grubb <sgrubb@redhat.com>
Almost innocuous; this is value is checked later, this
check being wrong would make it check stack garbage.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2655 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Via code review by Steve Grubb <sgrubb@redhat.com>
Also minor fixes for the message from "fill": the byte
count is unsigned, not signed; and more importantly,
print the real number of bytes written
git-svn-id: svn://svn.berlios.de/openocd/trunk@2652 b42882b7-edfa-0310-969c-e2dbd0fdcd60
on the command line ... matching comment in add_default_dirs().
Without this it's impossible to use a private config file which
happens to have the same name as an installed one. Say, because
you're bugfixing a private copy...
git-svn-id: svn://svn.berlios.de/openocd/trunk@2649 b42882b7-edfa-0310-969c-e2dbd0fdcd60
that were added after ARMv5TE was defined:
- ARMv5J "BXJ" (for Java/Jazelle)
- ARMv6 "media" instructions (for OMAP2420, i.MX31, etc)
Compile-tested. This might not set up the simulator right for the
ARMv6 single step support; only BXJ branches though, and docs to
support Jazelle branching are non-public (still, sigh).
ARMv6 instructions known to be mis-handled by this disassembler
include: UMAAL, LDREX, STREX, CPS, SETEND, RFE, SRS, MCRR2, MRRC2
git-svn-id: svn://svn.berlios.de/openocd/trunk@2644 b42882b7-edfa-0310-969c-e2dbd0fdcd60
With DCCR we are asking the CPU to halt, we should wait until
the CPU has halted before proceeding with the operation.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2638 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the ITR register but it will only be executed when the DSCR[13]
bit is set. The documentation is a bit weird as it classifies
the DSCR as read-only but the pseudo code is writing to it as
well. This is working on a beagleboard.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2634 b42882b7-edfa-0310-969c-e2dbd0fdcd60
instruction to be finished. This comes from the pseudo code
of the cortex a8 trm.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2632 b42882b7-edfa-0310-969c-e2dbd0fdcd60
"next iteration" step with the rest of the loop overhead.
Cleanup: remove spurious whitespace, and an overlong line;
only assign "tap->hasidcode" once.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2631 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Bugfixes:
* internal osc: it's *12* MHz (not 15 MHz) on _current_ chips
+ except new Tempest parts where it's 16 MHz (and calibrated!)
+ or some old Sandstorm ones, where 15 MHz was valid
* crystal config:
+ read and use the crystal config, don't assume 6 MHz
+ know when that field is 4 bits vs 5
* an RCC2 register may be overriding the original RCC
+ more clock source options
+ bigger dividers
+ fractional dividers on Tempest (NYET handled)
* there's a 30 KHz osc on newer chips (for deep sleep)
* there's a 32768 Hz osc on newer chips (for hibernation)
- Cosmetic
* say "rev A0" not "vA.0", to match vendor docs
* don't always report master clock as an "estimate":
+ give the error bound if it's approximate, like "±30%"
+ else don't say anything
* fix whitespace and caps in some messages
* these are not AT91SAM chips!!
Those clock issues might explain problems sometimes reported when
writing to Stellaris flash banks; they affect write timings.
That 12-vs-15 MHz issue is problematic; there's no consolidated doc
showing which chips (and revs!) have which internal oscillator speed.
It's clear that only older silicon had the faster-and-less-accurate
flavor. What's less clear is which chips are "old" like that.
Lightly tested, on a DustDevil part.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2626 b42882b7-edfa-0310-969c-e2dbd0fdcd60
For ARMv4/ARMv5:
- better command parameter error checking
- don't require an instruction count; default to one
- recognize thumb function addresses
- make function static
- shorten some too-long lines
For Cortex-M3:
- don't require an instruction count; default to one
With the relevant doc updates.
---
Nyet done: invoke the thumb2 disassembler on v4/v5,
to better handle branch instructions.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2624 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Unify the handling of the req_srst parameter, and rip out a
large NOP branch and its associated FIXME. (There didn't seem
to be anything that needs fixing; but that was unclear since
the constraints were scattered all over the place not unified.)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2623 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Unify the handling of the req_tlr_or_trst parameter. Basically,
JTAG TMS+TCK ops ("TLR") is always used ... unless TRST is a safe
option in this system configuration.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2622 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Track whether TRST and/or SRST actually change:
* If they're not changing, don't ask the JTAG adapter to do anything!
(JTAG TCK/TMS ops might still be used to enter TAP_RESET though.)
* Don't change their recorded values until after the adapter says it
did so ... so fault paths can't leave corrupt state.
* Detect and report jtag_execute_queue() failure mode
* Only emit messages saying what really changed; this includes adding
an omitted "deasserted TRST" message.
* Only apply delays after deasserting SRST/TRST if we *DID* deassert!
- Messages say "TLR" not "RESET", to be less confusing; there are many
kinds of reset. (Though "TLR" isn't quite ideal either, since it's
the name of the TAP state being entered by TMS+TCK or TRST; it's at
least non-ambiguous in context.)
So the main effect is to do only the work this routine was told to do;
and to have debug messaging make more sense.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2621 b42882b7-edfa-0310-969c-e2dbd0fdcd60
reset operations. Maybe they can't; or it's a "not yet" thing.
Note that the assert/deassert operations can't yet trigger for
OMAP3 because resets currently include JTAG reset in all cases,
resetting the ICEpick and thus disabling the TAP for Cortex-A8.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2620 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the values that are written in the mini-IC (plus documentation updates that
describe why this is needed).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2613 b42882b7-edfa-0310-969c-e2dbd0fdcd60
nonfunctional cortex_a8 code with something that at least basically
works (for halt/step/resume, without MMU) even if it is incomplete.
(With tweaks from Øyvind, and cleanup from Dave.)
This code has mainly been developed and tested against R1606, it has
been built and tested against R2294 where it runs but step and resume
commands are broken due to regression (which should be fixed now).
This code is really written for OMAP3530. It doesn't identify debug
resources using generic DAP calls to scan the ROM table, or perform
topology detection. The OMAP3530 DAP exposes two memory access ports:
- Port #0 is connected to L3 interconnect (the main bus) with
passthrough to the L4 EMU bus ... so it will be used for most
memory accesses.
- Port #1 is connected to a dedicated debug bus (L4 EMU), with
access to L4 Wakeup, and holds the ROM table ... so it must
be used for most debug and control operations.
The are some defines to handle this in cortex_a8.c, which should be
replaced with more general code. Having access to another Cortex-A8
implementation would help get that right.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2609 b42882b7-edfa-0310-969c-e2dbd0fdcd60
and seed it with DAP access support using the current ADIv5 code.
(With tweaks and cleanup from Øyvind and Dave.)
The ARMv7-AR architecture manual is not publicly available (even
in subset form like the ARMv7-M spec), so it's hard to distinguish
between the Cortex-A8 implementation and the ARMv7-A architecture.
The register set presumably is architectural, and so it's stored
here; it's like earlier ARMs, with small additions. Ditto the
instruction set, though Thumb2 support is used (extending Thumb
support from ARMv6 with more 32-bit instructions) and there's this
ThumbEE thing too. There is a new "debug monitor" mode, not yet
fully addressed here, to support debugging in environments (like
motor control) where halting debug mode is inadvisable.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2608 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The trunk is currently broken for interfaces without
the speed_div function (interface specific clock speed
value to kHz conversion). Example: parport.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2605 b42882b7-edfa-0310-969c-e2dbd0fdcd60
SVF file, making OpenOCD compatible with files generated by
Altera Quatrus II 9.0.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2600 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- warning now issued if high speed ftdi device found and openocd was built using an old driver
git-svn-id: svn://svn.berlios.de/openocd/trunk@2599 b42882b7-edfa-0310-969c-e2dbd0fdcd60
ARMv7-M: A5.3.6 Load/store dual or exclusive, table branch
GCC will generate the table branch instructions, usually with inlined
tables that will confuse this disassembler. LDREX and STREX are not
issued by GCC without inline assembly.
This means all Thumb2 instructions implemented by Cortex-M3 can now
be disassembled. Cortex-A8 cores support more Thumb2 instructions,
but most of those aren't yet publicly documented.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2598 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- spell "address" right
- list bp/wp params as optional
And make those source lines wrap at sane margins.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2596 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- AIRCR_SYSRESETREQ is generic; use it on any system where
SRST won't fly, not just on Stellaris-based ones.
- Reformat and improve comments about the Stellaris quirk; and
xref the only public docs (an email) about the issue.
It seems that *most* Stellaris chips have this problem. Tempest
parts aren't yet in general sampling; and if rev B silicon for
earlier chips exists, it's not very visible yet.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2595 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Simplify dumping of register lists by only printing cached values
if they are marked as valid. Most of the time, they are invalid;
so printing *any* value is just misleading.
Note that for ARM7 and ARM9 most EmbeddedICE registers (except for
debug status) could be cached most of the time; and their register
cache isn't maintained properly (many accesses seem to bypass that
cache code).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2594 b42882b7-edfa-0310-969c-e2dbd0fdcd60
https://lists.berlios.de/pipermail/openocd-development/2009-August/009939.html
1. It can only be built with the FTD2XX driver. libftdi supports FT2232H/FT4232H
since version 0.16
2. A speed value of 0 is used as a RTCK request indicator. This clashes with the
valid clock division value 0 that provide the highest fixed clock frequency.
3. The ft2232_speed_div function return the maximum selectable frequency (30MHz)
when RTCK is activated. It should return 0.
4. The ft2232_khz function return ERROR_OK when RTCK is requested even for
devices lacking RTCK support. It should return ERROR_FAIL so the upper driver layers
can detect this and try to fallback to a fixed frequency.
5. FT2232H/FT4232H have a backward compatibility function that divide the clock
by 5 to get the same frequency range as FT2232D. There is no code that disable
this functionality. I can not find anything about if this is enabled or disabled by default.
I think it is safest to actively disable it.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2591 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Change jtag_rclk behaviour so it can be called before the interface init function
git-svn-id: svn://svn.berlios.de/openocd/trunk@2590 b42882b7-edfa-0310-969c-e2dbd0fdcd60
issue with this is that the core debug support uses this
mechanism, then trashes its state over reset. Users can
Work around that (for now) by re-assigning the desired
config after reset.
Also fixes "target halted due to target-not-halted" goof.
When we can't describe the reason using OpenOCD's limited
vocabulary, say "reason undefined" instead of saying it's
not halted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2588 b42882b7-edfa-0310-969c-e2dbd0fdcd60
arrays (error prone) or assume all registers are 32-bits wide (they can
have fewer bits); don't use spaces in register names, so they can be
passed more easily to the "reg" command.
Minor updates for ARM9 vector_catch support: it's an 8-bit value. This
seems to help this core's vector_catch command work a bit better; but its
behavior wih the register cache is still goofy.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2587 b42882b7-edfa-0310-969c-e2dbd0fdcd60
display them as 32 bits unless that's their true size.
(Removes some confusion.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2586 b42882b7-edfa-0310-969c-e2dbd0fdcd60
OpenOCD was able to access only to chips attached to first EMIF
chipselect. This patch fixes chipselect management code and allows
OpenOCD to access to NAND devices attached to any EMIF CS line.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2585 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add flash programming support for NXP LPC1700 cortex_m3 based family
git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Warn about anyone using "jtag_speed" commands; that command is obsolete, and will someday be removed.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2578 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- revert patch from rev1507 as it was causing reset issues with arm9 cores
git-svn-id: svn://svn.berlios.de/openocd/trunk@2574 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.11 Data processing (shifted register)
The usual kinds of problems; the most noteworthy were that
the "S"et flags bit was mis-handled in these instructions.
---
This is the last patch from a quickie set of tests covering all
encodings of the instructions with 32-bit opcodes. There may
be some corner cases left, plus the instructions that aren't
yet handled, but the Thumb2 disassembler is no longer just
"lightly" tested with GCC output ... the new code paths have
mostly been verified.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2568 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.5 Load/store multiple
A5.3.7 Load word
There was a longstanding bug in Thumb-1 LDM; the rest of the LDM/STM
fixes are just using width specs to match UAL syntax, except for two
opcode name typos. Load word had two bitmask goofs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2567 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.8 Load halfword, unallocated memory hints
It's mostly the usual sort of bitmasking goofage and getting the
width specs right. In one case an older x86 GCC generated bad code
unless I structred a conditional differently (sigh).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2566 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.5 Load/store multiple
A5.3.7 Load word
There was a longstanding bug in Thumb-1 LDM; the rest of the LDM/STM
fixes are just using width specs to match UAL syntax, except for two
opcode name typos. Load word had two bitmask goofs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2565 b42882b7-edfa-0310-969c-e2dbd0fdcd60
ARMv7-M arch manual:
A5.3.1 Data processing (modified immediate)
A5.3.3 Data processing (plain binary immediate)
A5.3.4 Branches and miscellaneous control
and other (immediate) encodings referenced there. Several of
these just tweak the new syntax ("Unified" ARM/Thumb: UAL) but
there were a few bugs too.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2564 b42882b7-edfa-0310-969c-e2dbd0fdcd60
with testcases covering several new encodings in these sections
of the ARMv7-M arch manual:
A5.3.12 Data processing (register)
A5.3.13 Miscellaneous operations
A5.3.14 Multiply, and multiply accumulate
A5.3.15 Long multiply, long multiply accumulate, and divide
The issues were mostly in '12 and '13; some new related 16-bit
opcodes had issues too.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2563 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Dump SP on poll, and show whether it's MSP or PSP.
Thread mode can use either stack pointer, so this is
part of the state that's not yet displayed.
Shrink some lines.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2555 b42882b7-edfa-0310-969c-e2dbd0fdcd60
dbrownell
oharboe
ntfreak
mlu
duane
zwelch