The halt event was left pending in the CTI, better to clear it immediately
after debug entry.
Change-Id: I6002f862681baf98769e3c73332a7f7f0ef938c1
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4030
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch contains a major overhaul of the target run control,
mainly for the sake of satisfying gdbs ideas of how a target
should respond to various control requests for the debugger.
The changes allow gdb a slightly better control on how cores
are stepped: a core can be single-stepped while
other cores remain halted or continue normal execution
until the single-stepped core halts again.
Also, on any halting event (user command or breakpoint) the
system is brought into a stable state with all cores halted
before the halt is signaled to the debugger.
This patch also transitions the target code to make use of the
new CTI abstraction instead of accessing CTI registers directly.
Change-Id: I8ddc9abb119e04580d671b57ee12240c3f5070a0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3993
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
- rename "cortex_a" command group to "aarch64"
- remove default blank check, checksum and algorithm hooks
since they're not going to work in aarch64 mode anyway.
Change-Id: Ieb0046786ed9425baf6774c68f42a8285cc2aefd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3991
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Make sure all core register caches are invalidated on reset
assert, make sure to re-init debug registers on deassert.
Change-Id: I82350d04cc3eaae5e35245d13d6c1fb0a8d59807
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3990
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
introduce armv8_set_dbgreg_bits() function to make register
bit-field modifications easier to read.
Change-Id: I6b06f66262587fd301d848c9e0645e8327653de7
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3989
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Mmu faults can not be prevented on aarch64, they need to be taken and
handled accordingly. Remove the remaining stub code.
Change-Id: I6241efa594fe6b963624f9628cdf1c8e46588223
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3987
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Suppress some very verbose LOG_DEBUG's that are not really useful
any more.
Change-Id: I67f10ba9510a9e34a027f378f4b62b8901ddc8a4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3984
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reduce SLOCs in SCTLR retrieval and modification functions and make them
less complex.
Change-Id: Ida1a99c223743247f171b52eef80dc9886802101
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3982
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use the correct opcode for Aarch32 state, both for the breakpoint
instruction itself and the cache handling functions.
Change-Id: I975fa67b1e577b54f5c672a01d516419c6a614b2
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3981
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
At framework level, the resume hook is not protected. Make sure to
not attempt a resume if the target is not halted.
Change-Id: I4dd1975a95d6c513bd4f4e999e496bc11182a97a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Basically port a fix that was already done for the cortex_a target.
Change-Id: I4cf4519159bda03ed611bc0b2e340a5dad2d85fe
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
arm commands are mostly unusable anyway, remove them. to be replaced
by aarch64 specific commands later
Change-Id: Ie994771bc0e86cff1c26f68f1f51ce8ec352a509
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Make debug and error messages more informative, fix spelling and
formatting errors
Change-Id: I7245f42c5153bcc95676270814d30e91c113aaed
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move clearing of DSCR "Sticky Error" condition to the
exception handling function. Clear once on entering debug state.
Change-Id: Iec1d09d6f2d9cdd7e92953da5ea19f3e399ca12c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
recommended for Corte-A8 cores, not sure if necessary
for ARMv8 based cores as well.
Change-Id: Ibcb36170c5fac6a6b132de17f734c70a56919f9b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Remove register cache invalidation and target state changes that are
handled appropriately in other functions.
Change-Id: Ic903f41ddc267f4b8765ea022bd4d6da1017e21f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When a PE is in Aarch32 state and gdb asks for a target description,
provide a register view compatible with the "org.gnu.gdb.arm.core"
feature. Only current-mode registers are exported, banked registers are
not visible.
Change-Id: I99a85d94831cf597fe8cff6a0a1818ce0a33613b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When halting a group of PEs through CTI, HDE must be set in EDSCR for
all of them.
Change-Id: Iaa4bc0b0fe31e46a463c709d8274023225affd85
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
When an armv8-a PE causes an exception while halted, e.g. by performing
a prohibited memory or register access, its state is affected in the
same way as if it was running. That means, a number of registers is
overwritten (notably DLR and DSPSR, but also others) and also
potentially the exception level and therefore also the PE state can
change. This state must be restored before resuming normal operation.
This is done by marking the relevant cached registers "dirty" so that
they are written back before resume.
Change-Id: I9b6967a62d7cb23a477a9f7839f8d2b7087eed09
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
DCPS only allows to enter higher ELs, for lower ELs you need to
use DRPS. Also, of course the encoding differs between A64 and T32.
Both DCPS and DRPS also clobber DLR and DSPSR, which then need to be
restored on resume.
Change-Id: Ifa3dcfa94212702e57170bd59fd0bb25495fb6fd
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
All register access is now performed through common read/write
functions, which delegate the actual register access to the
armv8_common object. armv8_common contains function pointers
to direct read and write requests to the respective low-level
functions for each PE state.
The respective read/write functions are selected on debug state
entry.
At the same time, T32 opcodes are now formatted for ITR in
dpmv8_exec_opcode() and the T32_FMTITR macro is removed from global
visibility.
Change-Id: I9eaef017c7cc9e0c531e693c534901bfdbdb842c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
There's no access to system control register in EL0. Circumvent by
moving the PE to EL1 before reading, and switch back to original mode
afterwards.
Change-Id: I309f4eea5597ffc88fc892e9bbb826982e8a44ec
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use AT commands to translate virtual to physical addresses based on
current MMU configuration.
Change-Id: I1bbd7d674c435541b617b17022fa9f7f0f01bdab
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set HDE bit through helper function instead of manual mem_ap access.
Change-Id: I68c157870f3f3c47a875d425ade6e975d8075424
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Update cache identification to match functionality present in
armv7a_cache.c
Change-Id: I2dc4bee80f5a22b8728334d40331c183d1406f27
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Move all DPM related functions from aarch64.c to armv8_dpm.c.
Change-Id: I43404ff5db414ae898787a523d3219e5bee44889
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Add database for common, equivalent opcodes for Aarch32 and
Aarch64 execution states
Revisit all functions that access Aarch64 specific registers
or use Aarch64 opcodes and rewrite them to act depending on
current state of the core.
Add core register access functions for Aarch32 state
Add function to determine the core execution state without
reading DSPSR.
Change-Id: I345e9f6d682fb4ba454e4b1d16bb5e1b27570691
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Set up CTI so that halt and resume requests get routed to all PEs in the
SMP group.
Change-Id: Ie92cfd3fe54632e5fdc049a6bf5b24b99451a8c9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
On live hardware, interrupts will happen while the core is
held for stepping. The next step will most of the time execute an
interrupt service instead of the next line of code, which is not
what you expect. Disable interrupts through DSCR before resuming
for a step, and re-enable them again after the step happened.
This should be made configurable, like on cortex_a target.
Change-Id: I94d8ffb58cf7579dedb66bc756b7eb6828b6e8e4
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
External debuggers need to use HLT, not BRK. HLT generates a halting
debug event while BRK generates a debug exception for self-hosted
debugging.
Change-Id: I24024b83668107f73a14cc75d951134917269e5c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Don't report breakpoint as debug reason when halt is due to a
single-step event.
Change-Id: Ie6c3ca1e5427c73eb726a038301b6a29a47d1217
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reduce complexity of memory access functions, anyway there are no ARMv8
platforms that actually contain an AHB-AP at all. while at it, fix
virt-to-phys function signatures to expect target_addr_t.
Change-Id: I55a369686f42993988b6323e5a77f38de12530a9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The step command optionally carries a resume address. In this case,
stepping should start not at the current PC, but at the given address.
Change-Id: Id5792a3745f470cf29efa90c63d65f33d36f6b25
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Make DSCR_RUN_MODE() usable for armv8 and arm7 debug
Change-Id: Ib3ba3000d5b6aa03e590f3ca4969e677474eb12c
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Page table layout in aarch64 is very different from armv7-a layout.
Remove the incorrect handling, to be replaced correct armv8 code in a
later patch
Change-Id: I64c728a72a24f9f4177726ccc07a02a8ca0d56ce
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Not only null control but also value of the breakpoint when it is
removed.
Change-Id: Id99c7e3644729c64e563f1fa8b0577f350be6a98
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
armv8 breakpoint register spacing is 16, not 4 as in armv7-a
Change-Id: I0d49d06878a0c9dab35cde478064e5366f01a8e0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use correct instructions to access CLIDR, CSSELR and CCSIDR.
Change-Id: I319b96c03a44fdb59fcb18a00f816f6af0261f0a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
- armv8 EDSCR has no ITR_EN bit, ITR is always enabled. Writes to this
bit are ignored but we should not do them anyway
- use dpmv8 function to report the reason for debug entry
- WFAR is a 64bit register
Change-Id: I07b81ecf105ceb7c3ae2f764bb408eb973c1d1de
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use opcode definitions from armv8_opcodes.h where appropriate
Change-Id: Iead33fb8e62eb2dd2419ef8932f7d46c087f51a8
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
The system control register has several instances, depending on the
exception level. Make sure to access always access the correct one.
Change-Id: I9e867f4dbd9625762042f20ed905064ea4e3270f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Flush DTRRX with a dummy read if it's full, clear sticky errors
by writing CSE bit to EDRCR register.
Change-Id: Ia42ae9d3859ba6cbe892d48584e21acdd4e25c84
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Use configured CTI base address instead of hardcoded value, if
available.
Use symbolic constants instead of raw hex offsets.
Trim halt and resume code to what is actually necessary.
Change-Id: I4997c2bcca7cebf5ad78859a6a12abe8639594ed
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Fix 64bit address setting
Fix register spacing (16 instead of 4)
Set HMC bit for all but linked context match breakpoints,
where the bit is ignored anyway
Change-Id: I48428f39154a6fe5fadc075ca918d1500a0bb241
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Matthias Welwarsky