In a corner case when debug_ap is not available,
cortex_m_assert_reset() asserts reset to restore
communication with the target.
Prevent to do so on targets with defer_examine,
as such targets need some special handling to enable them
after reset anyway.
The change makes possible to handle a multicore Cortex-M SoC with
an auxiliary Cortex-M core(s) switched of by default
even with 'reset_config srst_gates_jtag'
Change-Id: I8cec7a816423e588d5e2e4f7904c81c776eddc42
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8097
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Previously, the gpio_num and chip_num members of adapter_gpio_config
were typed as 'int' and a sentinel value of -1 was used to denote
unconfigured values.
Now, these members are typed as 'unsigned int' to better reflect their
expected value range.
The sentinel value now maps to UINT_MAX as all adapters either define an
upper bound for these members or, in the case of bcm2835gpio, only
operate on a specific chip, in which case the value doesn't matter.
Format specifiers have been left as %d since, when configured, valid
values are within the positive range of 'int'. This allows unconfigured
values to display as a more readable value of -1 instead of UINT_MAX.
Change-Id: Ieb20e5327b2e2e443a8e43d8689cb29538a5c9c1
Signed-off-by: Vincent Fazio <vfazio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8124
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Jlink driver floods the debug log by a message per one poll interval.
Avoid annoying messages, change their logging level to LOG_DEBUG_IO
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I84ea6aa9cdfd44b5985c5393519d1efb7de9530a
Reviewed-on: https://review.openocd.org/c/openocd/+/8116
Reviewed-by: zapb <dev@zapb.de>
Tested-by: jenkins
The target esirisc does not free the allocated memory resources,
causing memory leaks at OpenOCD exit.
Add esirisc_free_reg_cache() and esirisc_deinit_target() and use
them to free all the allocated resources.
Change-Id: I17b8ebff54906fa25a37f2d96c01d010a98cffbd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8094
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
The function in question does not need to change target state. It is a
target-type-dependant function, however, IMHO, it is safe to assume that
any target type would not need to change type-independant state of a
target to figure out the arch.
Change-Id: I607cb3aee6529cd5a97bc1200a0226cf6ef43caf
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8093
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are quite a lot of "getters" in target interface.
They do not change target structure, nevertheless the structure is
passed to these functions via a plain pointer.
The intention is to clarify the purpouse of these functions by passing
the `target` structure as a pointer to constant data.
Change-Id: Ida4a798da94938753b86a293a308d93b091d1bf3
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8092
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Example for configuring multiple non-SMP
Xtensa cores e.g. for heterogeneous debug
- JTAG only at this time; DAP out of scope
- Dual-Xtensa Palladium example via VDebug
- Update Xtensa core config examples
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I6d2b3d13fa8075416dcd383cf256a3e8582ee1c1
Reviewed-on: https://review.openocd.org/c/openocd/+/8078
Tested-by: jenkins
Reviewed-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This change implements the support for the ARM Debug Interface v6.
The DAP-level interface properly selects the DP Banks and AP address.
Sample ARM configuration DAP and JTAG scripts have been updated.
Change-Id: I7df87ef764bca587697c778810443649a7f46c2b
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8067
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the socket option RCVLOWAT is not supported on CYGWIN.
implemented ifdef __CYGWIN not to set this option.
Change-Id: I9f6e81fa98ecf5261ea286deb4675658aae59b8e
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8066
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This file is intended to be included in any user's project that
plans to use OpenOCD awareness for uCOS-III.
It is supposed to be distributed under a license compatible with
the uCOS-III code, that is Apache-2.0 license.
Distribute it under Apache License 2.0.
Change-Id: I51ecd469c8ccdd23a069d21e89b7d90886691395
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7996
Tested-by: jenkins
Add the full text of the Apache-2.0 license to the OpenOCD tree.
It has the same content from:
https://spdx.org/licenses/Apache-2.0.html#licenseText
but reformatted as in the Linux kernel document and added the
required tags for reference and tooling.
While this commit is specific for standalone files, it already
reports the information for dual licensing.
Change-Id: I1fd427256c310ab733fb5d50f344ac52c64a56f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8005
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Correct GPIO Extender configuration, after reconsideration,
we need to configure the IO extender 0x23 pins as all inputs.
Add more LOG_ERRORs to the code to better track bugs.
Re-organize angie_init function
Change-Id: I1fcf4919ba9ea95576803dd35cce7dafa26853b4
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8079
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Clang static analyzer warnings
"1st function call argument is an uninitialized value"
on the first libusb_free_transfer() parameter (lines 423, 424)
could turn into a real problem in a corner case:
If allocation of a libusb transfer struct fails, the pointers of not yet
allocated transfers remain uninitialized.
Use calloc() to zero whole struct cmsis_dap_backend_data.
Fixes: fd75e9e542 (jtag/drivers/cmsis_dap_bulk: use asynchronous libusb transfer)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I0e489757d82d10ed7416c5e8c215e1facc7f8093
Reviewed-on: https://review.openocd.org/c/openocd/+/8045
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function is used for commands:
- jtag configure
- jtag cget
While there, add the missing .usage field.
Change-Id: I97ddc4898259ddb7fd2d057a997f33a6f4b0e2a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8058
Tested-by: jenkins
Before this change, when we send an I2C Bulk data at the same
time while Jtag bitbanging functions execute, the microcontroller
puts JTAG bitbanging on wait and executes all I2C bitbanging
function, which causes problems like loss of Ack in DAP responses
and other errors.
With this commit, When I2C interruption occurs, it sets a variable
to true and continues JTAG bitbanging, when it finish it executes
the I2C bitbang.
Change-Id: Ia80bac21f8a259f4a1176b5346bf74ed0aa6e38b
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8074
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add GPIO extender initial configuration that is needed to configure
some important GPIOs and ensure that the dev board is ready to work.
Add i2c_write function that make a write transfer to any slave device.
Give a new Product ID to ANGIE to make it different than the non
programmed ANGIE.
Change-Id: I0a8dacb7fe218145b7d3ed1cb75f106ed6256714
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8072
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Give ANGIE a new PID after renumeration to be able to distinguish
the two cases (programmed and not programmed)
Change-Id: I30a91d8ed2e8e261221488b98d40a027ca41da52
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7991
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
remove angie_clear_queue function from executing before the
angie_execute_queued_commands function and making it at the
end of the reset function.
Change-Id: Id8a0664fbd5b8f9730545ce0f8f272ae0b0e7e78
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7990
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We want to keep the tri-state buffers located between the FPGA
and the board, in 'Z' state until we launch an i2c connection.
We launch an i2c start condition, make the SCL
direction 'OUT' to start the i2c protocol and at the end
of the i2c connection at the stop condition, we re-make
the tri-state buffers at 'Z' state.
Change-Id: Ic597a70d0427832547f6b539864c24ce20a18c64
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7989
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Send bitstream size to firmware to initialize the GPIF count registers,
since we're going to send this size via GPIF, we need to give the exact
number of bytes to be sent, then the GPIF counter will decrement with
every clock cycle (every byte sent) until reaching zero and stops.
Change-Id: Ib4e8e0f95a6a4a95ef4888ba8a04a0ea45567f5a
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7988
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change the GPIF state machine, configuring only one of the 4 waveforms
to generate the clock signal (CCLK) used to program the FPGA, and send
one byte every cycle using an 8-bit bus.
Change-Id: I43cf5480b9d5c40cc2f6a62a52ecfe078b76458e
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7976
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
clang build triggers an error for an uninitialized value of the
variable 'instr'.
This is a false positive, as the macro
#define MIPS32_CONFIG3_ISA_MASK (3 << MIPS32_CONFIG3_ISA_SHIFT)
guarantees the switch/case already covers all the possible values
with cases 0, 1, 2 and 3.
Silent clang by adding a useless default case to the switch.
While there, fix the indentation of the switch/case accordingly to
OpenOCD coding style.
Change-Id: I0ae316754ce7d091dd8366bf314b8e6ee780e313
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 7de4b1202d ("target/mips32: add cpu info detection")
Reviewed-on: https://review.openocd.org/c/openocd/+/8065
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Some OpenOCD command gets fragment of TCL scripts as command-line
argument, fragments that will be kept and executed later on.
E.g. the command 'configure' gets the body of an OpenOCD event:
$TARGET configure -event halted {TCL code}
These commands store the argument as a Jim_Obj and pass it to the
jimtcl interpreter when the TCL fragment has to be executed.
Using Jim_Obj as storage is relevant to let the jimtcl interpreter
to recover extra info of the TCL fragment, like the file-name and
the line-number that contain the fragment, that will be printed
out in case of run-time errors.
While converting the commands to COMMAND_HANDLER, we should avoid
storing the argument as C strings otherwise we will loose precious
info in case of run-time errors making challenging the debugging
of such TCL fragments.
Extend the struct command_invocation to contain the array that
points to the Jim_Obj of the command arguments.
This will be used while converting commands to COMMAND_HANDLER.
Change-Id: If37c5f20e9a71349f77ba1571baf1e6778e28aa5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8057
Tested-by: jenkins
The jimtcl interpreter guarantees that the Jim objects in argv[]
are not deallocated during the command execution. Thus, there is
no need to copy the string content of argv[].
Simplify exec_command() by inlining its two sub-functions and
dropping the strdup().
While there, add a LOG_ERROR() for out of memory.
Change-Id: I3e21ed7da50ca0bd072edbd49fca9740c81f95b0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8055
Tested-by: jenkins
The output parameter nwords is always equal to the input parameter
argc, when the function succeeds.
Drop the parameter nwords and let the caller use directly the
value in argc.
While there, convert some 'unsigned' to 'unsigned int'.
Change-Id: Ie3d8ce1351792f3c07fe39cdcbcd180fd24dc928
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8054
Tested-by: jenkins
In both functions script_debug() and script_command_args_alloc()
the variable len is never used, and Jim_GetString() does not
mandate it.
Drop the variable and pass NULL to Jim_GetString().
Change-Id: I754b27a59c6087cde729496be42609d2a7145b0c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8053
Tested-by: jenkins
Commit e370e06b72 ("target: Deprecate 'array2mem' and
'mem2array''") has already replaced the deprecated root versions
of commands mem2array and array2mem with TCL proc's that use
'read_memory' and 'write_memory'. It has left the deprecated code
of the target's version of the commands because the effort to code
the TCL replacement was not considered valuable.
To drop the last jim_handler commands, I consider much easier and
less error-prone to code them in TCL instead of converting the
deprecated code to COMMAND_HANDLER.
Drop the code in target.c and extend the TCL proc's.
While there, add the TCL procs to _telnet_autocomplete_skip.
Change-Id: I97d2370d8af479434ddf5af68541f90913982bc0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8052
Tested-by: jenkins
When requested by the core code (handle_breakpoints = true),
arc_resume() should be able to advance over a potential breakpoint set
at the resume address instead of getting stuck in one place. This is
achieved by removing the breakpoint, executing one instruction,
resetting the breakpoint, then proceeding forward as normal.
With this patch applied, openocd is now able to resume from a
breakpoint halt when debugging ARCv2 targets via telnet.
This has previously been committed to the Zephyr project's openocd repo
(see https://github.com/zephyrproject-rtos/openocd/pull/31).
Change-Id: I17dba0dcea311d394b303c587bc2dfaa99d67859
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7817
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Presently, we rely on gdb to restore break/watchpoints upon resuming
execution in arc_resume(). To match this behavior in absence of gdb
(more specifically, when handle_breakpoints is true), this patch
explicitly re-enables all breakpoints and watchpoints in arc_resume().
This has previously been committed to the Zephyr project's openocd repo
(see https://github.com/zephyrproject-rtos/openocd/pull/31).
Change-Id: I59e9c91270ef0b5fd19cfc570663dc67a6022dbd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7816
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
For Armv8.1-M based cores, detect if the core implements the optional
M-profile vector extension (MVE), using MVFR1 register.
While at there rework armv7m->fp_feature detection based on MVFR0
and MVFR1 registers.
Change-Id: I92d5b1759aea9f7561d285f46acdec51d6efb7b4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6950
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
By queuing multiple jtag transfers the connection speed between
JTAG-Host and JTAG-Hub is improved. This is due to much less
calls to OS functions. An improvement of about x30 has been
measured with ftdi-based jtag adapters
For this to work the JTAG-Host server needs to know if flow control
is enabled on the JTAG-Hub ports. This is possible with newer
JTAG-Hub/JtagCDC. For old JTAG-Hubs the queuing is not enabled so
this change is backwards compatible.
Change-Id: I8a5108adbe2a2c1e3d3620b5c9ff77a546bfc14e
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7978
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On some systems (at least Windows/CYGWIN and macOS) libusb_dev_mem_alloc()
simply returns NULL. The helper can fall-back to malloc() to allocate
CMSIS-DAP pending command/response buffers.
Fixes: fd75e9e542 (jtag/drivers/cmsis_dap_bulk: use asynchronous libusb transfer)
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I89660f6747ad9d494b8192711cbbee5764e058fa
Reviewed-on: https://review.openocd.org/c/openocd/+/8044
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
On some systems (at least Windows/CYGWIN and macOS) libusb_dev_mem_alloc()
simply returns NULL.
Use the result of the very first libusb_dev_mem_alloc() call to decide
if the underlining system supports dev mem allocation or we should
fall-back to plain heap malloc().
From the decision time on, keep using the selected type of memory allocator
and deallocator.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ia1f0965cea44b4bb6d936b02ec43f5a16a46f080
Reviewed-on: https://review.openocd.org/c/openocd/+/8059
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Based on Daniel Goehring's [1] and Peter Collingbourne's [2] work.
Probe for support of 8, 16 bit and if the large data extension is available
also probe for 64, 128 and 256 bit operations.
Probe for the ability of packing 8 and 16 bit data
(formerly probed in mem_ap_init()). The probe is integrated to
mem_ap_read/write() routines and takes place just before the first memory
access of the specific size.
Add 64, 128 and 256 bit MEM-AP read/writes.
Introduce specific error codes for unsupported transfer size
and for unsupported packing.
Change-Id: I180c4ef17d2fc3189e8e2f14bafd22d857f29608
Link: 7191: target/adiv5: add MEM-AP 64-bit access support | https://review.openocd.org/c/openocd/+/7191
Link: 7436: arm_adi_v5: Support reads wider than 32 bits | https://review.openocd.org/c/openocd/+/7436
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7576
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Prevent packed writes with Nuvoton NPCX quirks because the workaround
uses all byte lanes for one byte or halfword and thus precludes packing.
Eliminate quirk code for size 4 as it is equivalent to the common code.
Make the quirk code for sizes 2 and 1 easier readable.
Change-Id: I72324e56a49b4712bd3769e03dce01427d9fcd73
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7575
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Introduce ti_be_lane_xor for byte lane correction
and use common code for both quirk and regular conversion.
The same lane correction takes place in both mem_ap_read/write()
- it was obfuscated in original code with different bitwise and arithmetic
operations.
Change-Id: I6a30672b908770323d30813a714e06ab8695fe26
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7574
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Update mips32 instructions, add barrier and sync related insts.
Add SYNC and barrier instruction blocks for memory access safety.
These instructions are not supported on Lexra and/or MIPSr1 CPUs,
detections were added and they will be executed conditionally.
Rework mips32_pracc_read/write_regs function.
Checkpatch-ignore: MACRO_ARG_REUSE
Change-Id: Ib14112f37ff1f060b1633df73d671a6b09bb2178
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7865
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add detection for mips cpu types by using prid.
Add cpuinfo command for inspecting more verbose info.
Add MIPS Architecture specs in openocd docs.
Change-Id: I28573b7c51783628db986bad0e226dcc399b4fa6
Signed-off-by: Walter Ji <walter.ji@oss.cipunited.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7912
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
When Linux HID driver binds the USB endpoints of the adapter,
'lsusb' fails to read all the reports and prints
** UNAVAILABLE **
Detect this case and alert the user, providing also the proper
command to unbind the driver before running the script again.
Put this test at the end of the output, so user can easily see it.
Change-Id: Iaca00040e666b62ceebe4b842a24932799bde56a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8046
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested with APM32F103CBT6 using JTAG and SWD transport. All flash
operations, including sector and device protection, work as expected.
Change-Id: Ibefe1a65d710aea87b86ab7ff8a4153512a0ea4f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8017
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tomas Vanek
Vincent Fazio
Antonio Borneo
Evgeniy Naydanov
Ian Thompson
Jacek Wuwer
Ahmed BOUDJELIDA
Evgeniy Didin
Tarek BOCHKATI
Daniel Anselmi
David Vidrie Leon
Walter Ji
Marc Schink