if tap enable/disable failed then a warning was written to the log, but JIM_OK was returned. if using openocd via a TCP interface to the TCL port, there is no way to catch that the command failed (it didn't enable the tap, so it failed)
now it return an error if it fails.
There are some older atmel nor chips which have negated logic for
TopBottom detection. This patch adds a special handling for the old
chips. This is the same mechanism as implemented in linux kernel.
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
before doing anything with the flash module (FM) the clock divider must be set.
if erase_check was the first thing done with the FM after reset then an error would be generated because the clk divider was not set.
now erase_check sets the clk divider.
reorganized code to get rid of compiler warnings
the warning were related to allignment, i do not get these warning on my build system (i've tried setting the compiler flag but it doesn't work, still working on why) so i cannot detect them (yet.)
This corrects two issues found with openocd.
d7f71e7fe9 removed some code that was
being used.
The above then caused even more code to get removed by commit 1cfb2287a6.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Issue warning when the old cmd is used and redirect to new supported one.
These deprecated cmds will be removed at some point.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Use consistent names for the stm32 family flash drivers, eg.
stm32x -> stm32f1x
stm32f2xxx -> stm32f2x
this makes it easier to add support for newer stm32 families.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
When building official releases from tarball, git commit info is not
available in the building environment. Thus, automake should not try to
append the git commit to the version string.
Signed-off-by: Luca Bruno <lucab@debian.org>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The default is -Werror, so warnings become errors
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
A new variable "nobase_dist_pkglib_DATA" is introduced to install
the OpenULINK firmware image to $PREFIX/lib/openocd/OpenULINK/ulink_firmware.hex
Also, the variable "EXTRA_DIST" is used to include the OpenULINK firmware source
in the OpenOCD source distribution.
So far image_load command tries to load ELF binaries to address
discovered by reading p_paddr member of a Program header of an ELF
segment.
However, ELF specifications says for p_paddr : ...Because System V
ignores physical addressing for application programs, this member has
unspecified contents for executable files and shared objects.
ARM ELF specifiaction goes even further, demanding that this member
be set to zero, using the p_vaddr as a segment load address.
To avoid the cases to wrong addr where p_paddr is zero,
we are now using p_vaddr to as a load destination in case that *all*
p_paddr == 0. Basically, this patch re-implements the approach present in
BDF's elf.c, which is used by GDB also (so that we can be consistent).
cygwin does not define sleep, so use our internal win32 version.
caused by commit 9d4aec6bda
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
there was a check in clearing the status register that
called exit() if the target was running. target_write_memory()
has such a check and will report the error correctly.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
only set jtag global pointer if jtag->init() succeeds. Less code,
more clear what the rules are.
Fix nit that error value from init() was not propagated unmodified.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
- works on Cortex-M3 with ThreadX and FreeRTOS
Compared to original patch a few nits were fixed:
- remove stricmp usage
- unsigned compare fix
- printf formatting fixes
- fixed a bug with overrunning a memory buffer allocated with malloc.
Update devices as per the latest programming manual.
We now use the full DEVID to identify the target. Previously we used
a 8bit id but that has now been changed in the manual.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Freescale iMX53 doesn't seem to like unaligned accesses to his memory
mapped registers.
Anyway this patch makes dump_image/load_image 4X faster for every
access through APB.
Signed-off-by: Luca Ellero <lroluk@gmail.com>
accidentally invoked return jtag_execute_queue() in the
middle of a fn. Hmm.... I would have expected gcc or
at least lint to catch this.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the patchup code would get false positives when checking
whether a dbgbase had to be corrected.
The solution is to have autodetect default, with manual override
in scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Could this cause confusion as data sent to write would be flipped
and then if the caller subsequently used the data, e.g. a
compare mismatch might happen?
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Really a Cortex-A specific option, but there is no
system in place to support target specific options
currently and there has been no need for such a system
until now.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
production processor versions increment, thus the version
bits should be ignored for future proofing. e.g.
Engineering sample version == 0x00, production version 0x01
The patch below fixes step <address> on mips_m4k.
Spencer Oliver <spen@spen-soft.co.uk>:
The current code is used on all other arch's - is
there a underlying issue with those aswell ?
I don't think dsp563xx_once_read_register() would ever
be called with len==0, but it would have been broken in
that case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Problem is, trying to print "Hello, world!\n" just prints endless H's, because r1 is never incremented.
One way to fix it would be to add a "++" after "r1".
Fix a bunch of typos.
Most are in code comments, so nothing should break. UNKOWN_COMMAND and
CMD_UNKOWN are not used elsewhere, so correcting the spelling should
also not break anything.
only flush write queue just before waiting for more data,
rather than when fetching more data from the buffer.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Found by inspection: the correct thing in the context is to use
usleep() rather than jtag_sleep(). Relates to JTAG over TCP/IP
only.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
short sleeps are handled via usleep, longer sleeps we round up
to nearest ms.
There was a bug in jtag_sleep() in that it would round *down*
to nearest ms, thus making all <1ms sleeps 0. Found by inspection
rather than symptom.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
as said in the datasheet Section 3.3.2 Organization of buffers
All buffers are big enough to hold 2 KByte of data.
this will double the speed of download
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
this will allow us to use multiple jlink at the same time as when
the USB-Address is specified the PID change from 0x0101 to
(0x101 + usb_adress)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Drasko DRASKOVIC
Rodrigo L. Rosa
Andreas Bießmann
Øyvind Harboe
Jie Zhang
Spencer Oliver
Ronny Strutz
Luca Bruno
Steve Bennett
Peter Horn
Martin Schmölzer
Tomek CEDRO
Freddie Chopin
Stefan Mahr
Damjan Marion
Alan Bowman
Jie Zhang
Jonas Hörberg
Michel Jaouen
SimonQian
Alexandre Pereira da Silva
Broadcom Corporation (Evan Hunter)
Luca Ellero
Jean-Christophe PLAGNIOL-VILLARD
Ali Lown
Olivier Schonken
Andrew Lyon
Mathias K
John and Tina Peterson
Uwe Hermann