This should silence a warning.
Change-Id: Id91a9ebacae836083b1db2654a8e7bf24b2300e9
Signed-off-by: Edgar Grimberg <edgar.grimberg@gmail.com>
Reviewed-on: http://openocd.zylin.com/52
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Perhaps we could do one better and propagate the error?
Change-Id: Idc45f516c26f09de4ee01fe05e8d3475f4b80db3
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/43
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
may be used uninitialized in this function [-Werror=uninitialized]
Change-Id: Ida2cf8efe4e7da6fd9f669b806a20894563ac3d4
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/49
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Fix a few errors with set and unused variables detected by GCC 4.7.0
Change-Id: I59b748e18e514ee9f0cde7883b4ed5116198bd4a
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/36
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The code in xscale_receive() that tries to skip invalid reads (i.e.
reads that don't have the DBG_SR[0] 'valid' bit set) seems to be
wrong, as it only looks at the first word's valid flag rather than
each word's own valid flag. Am I reading the code correctly? If so,
the attached patch should fix it.
If this looks correct, I'll generate a proper patch and commit message.
Matt
Change-Id: I74ebe2ad7a36d340a9dd3b8487578b6ea7f3cf1e
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/32
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
by immediately polling again when we have received a message from
the target instead of waiting 100ms, we can hope for much better
performance. More than 100x? :-)
Change-Id: Ieaf0c6c8b6e5addc482895670ffbf9a743e07a29
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/27
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Tested-by: Øyvind Harboe <oyvindharboe@gmail.com>
Change-Id: I1453f4f3dc0add529da20577e38b8b82d7d00366
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/18
Reviewed-by: Alex Austin <alex.austin@spectrumdsi.com>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Let the target algorithm be running in the background and buffer data
continuously through a FIFO. This reduces or removes the effect of latency
because only a very small number of queue executions needs to be done per
buffer fill. Previously, the many repeated target state changes, register
accesses (really inefficient) and algorithm uploads caused the flash
programming to be latency bound in many cases. Now it should scale better
with increased throughput.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Access the different flash banks' registers using a bank specific register
base and a register specific offset. This is equivalent but feels more
natural.
Some accesses were discovered that maybe should not be hard coded to bank0
registers. Add a note about that.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Split armv7m_run_algorithm into two pieces and use them to reimplement it.
The arch_info parameter is used to keep context between the two calls, so
both calls must refer to the same armv7m_algorithm struct. Ugly but works
for a proof-of-concept.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
On supported targets, this may be used to start a long running algorithm in
the background so the target may be interacted with during execution and
later wait for its completion.
The most obvious use case is a double buffered flash algorithm that can
upload the next block of data while the algorithm is flashing the current.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Target events are added to get better gdb support. The run
algorithm functionality are implemented to support feature
fast flash write functionality. The new r/w buffer api is now
used to support the special memory address handling. The output
of the md command was fixed.
This is a proof of concept to get access to the debug port of a
secured kinetis cpu. On full flash erase the cpu is automatically
secured and the debug port is not accessible.
To get this to work the srst line is needed and the necessary
configuration should be added to the configuration file.
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
added an attempt to use the non-reseting halting sequence. if it fails, then the full sequence will be attempted. this makes things a bit faster most of the time.
changed the location of a function, avoiding a forward def
Edgar Grimberg
Antonio Borneo
Øyvind Harboe
Spencer Oliver
Andreas Fritiofson
Freddie Chopin
Marc Willam / Holger Wech
Matt Reimer
Attila Kinali
Spencer Oliver
Michel Jaouen
Simon Barner
Clément Burin des Roziers
Steve Bennett
Mathias K
Luca Bruno
Richard Uhler
Martin Schmölzer
Rodrigo L. Rosa