Unneeded exports cause confusion about the module interfaces.
Only the Feroceon code builds on this, so only routines it
reuses should be public.. Make most remaining functions
static, and fix some of the line-too-long issues.
The forward decls are just code clutter; move their references
later, after the normal declarations. Turns out we don't need
even one forward declaration in this file.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The Hex parser uses a fixed number of sections. When the
number of sections in the file is greater than that, the
stack get corrupted and a CHECKSUM ERROR is detected
which is very confusing.
This checks the number of sections read, and increases
IMAGE_MAX_SECTIONS so it works on my file.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Only type 1 branch instruction has a condition code, not type 2.
Currently they're both tagged with ARM_B which doesn't allow for the
distinction.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
A Thumb BLX instruction is branching to ARM code, and therefore the
first 2 bits of the target address must be cleared.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch includes partial support for these new JTAG adapters.
More complete support will require updates to the libftdi code,
for EEPROM access.
[dbrownell@users.sourceforge.net: fix whitespace, linelen, etc ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Currently, OpenOCD is always caching the PC value without the T bit.
This means that assignment to the PC register must clear that bit and set
the processor state to Thumb when it is set. And when the PC register
value is transferred to another register or stored into memory then
the T bit must be restored.
Discussion: It is arguable if OpenOCd should have preserved the original
PC value which would have greatly simplified this code. The processor
state could then be obtained simply by getting at bit 0 of the PC. This
however would require special handling elsewhere instead since the T bit
is not always relevant (like when PC is used with ALU insns or as an index
with some addressing modes). It is unclear which way would be simpler in
the end.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Whenever an unconditional branch with the H bits set to 0b10 is met, the
offset must be combined with the offset from the following opcode and not
ignored like it is now.
A comment in evaluate_b_bl_blx_thumb() suggests that the Thumb2 decoder
would be a simpler solution. That might be true when single-stepping of
Thumb2 code is implemented. But for now this appears to be the simplest
solution to fix Thumb1 support.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Calling it first with every opcodes and then testing if the opcode
was indeed a branch instruction is wasteful and rather strange.
If ever thumb_pass_branch_condition() has side effects (say, like
printing a debugging traces) then the result would be garbage for most
Thumb instructions which have no condition code.
While at it, let's make the nearby code more readable by reducing some of
the redundant brace noise and reworking the error handling construct.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make the "dap info" output more comprehensible:
- Don't show CIDs unless they're incorrect (only four bits matter)
- For CoreSight parts, interpret the part type
- Interpret the part number
- Show all five PID bytes together
- Other minor cleanups
Also some whitespace fixes, and shrink a few overlong source lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Ignore leading '0' characters on hex strings. For example a bit
pattern consisting of 6 bits could be written as 3f, 03f or 003f and
so on.
Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds basic autoprobing support for the JTAG scan chains
which cooperate. To use, you can invoke OpenOCD with just:
- interface spec: "-f interface/...cfg"
- possibly with "-c 'reset_config ...'" for SRST/TRST
- possibly with "-c 'jtag_khz ...'" for the JTAG clock
Then set up config files matching the reported TAPs. It doesn't
declare targets ... just TAPs. So facilities above the JTAG and
SVF/XSVF levels won't be available without a real config; this is
almost purely a way to generate diagnostics.
Autoprobe was successful with most boards I tested, except ones
incorporating C55x DSPs (which don't cooperate with this scheme
for IR length autodetection). Here's what one multi-TAP chip
reported, with the "Warn:" prefixes removed:
clock speed 500 kHz
There are no enabled taps. AUTO PROBING MIGHT NOT WORK!!
AUTO auto0.tap - use "jtag newtap auto0 tap -expected-id 0x2b900f0f ..."
AUTO auto1.tap - use "jtag newtap auto1 tap -expected-id 0x07926001 ..."
AUTO auto2.tap - use "jtag newtap auto2 tap -expected-id 0x0b73b02f ..."
AUTO auto0.tap - use "... -irlen 4"
AUTO auto1.tap - use "... -irlen 4"
AUTO auto2.tap - use "... -irlen 6"
no gdb ports allocated as no target has been specified
The patch tweaks IR setup a bit, so we can represent TAPs with
undeclared IR length.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Stop allocating three bytes per IR bit, and cope somewhat better
with IR lengths over 32 bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove needless debug handler state.
- "handler_installed" became wrong as soon as the second TRST+SRST
reset was issued ... so the handler was never reloaded after the
reset removed it from the mini-icache.
This fixes the bug where subsequent resets fail on PXA255 (if the
first one even worked, which is uncommon). Other XScale chips
would have problems too; PXA270 seems to have, IXP425 maybe not.
- "handler_running" was never tested; it's pointless.
Plus a related bugfix: invalidate OpenOCD's ARM register cache on reset.
It was no more valid than the XScale's mini-icache. (Though ... such
invalidations might be better done in "SRST asserted" callbacks.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Bit 5 shouldn't be used. Remove all support for modifying it.
Matches the exception vector table, of course ... more than one
bootloader uses that non-vector to help distinguish valid boot
images from random garbage in flash.
Some cosmetic cleanup, and switch to a single table mapping
between state names and symbols (vs two routines which only
share that state with difficulty).
Get rid of TAP_NUM_STATES, and some related knowledge about
how TAP numbers are assigned. Later on, this will help us
get rid of more such hardwired knowlege.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
- Use the name mappings all the other code uses:
+ name-to-state ... needed to add one special case
+ state-to-name
- Improve various diagnostics:
+ don't complain about a "valid" state when the issue
is actually that it must be "stable"
+ say which command was affected
- Misc:
+ make more private data and code be static
+ use public DIM() not private dimof()
+ shorten the affected lines
Re the mappings, this means we're more generous in inputs we
accept, since case won't matter. Also our output diagnostics
will be a smidgeon more informative, saying "RUN/IDLE" not
just "IDLE" (emphasizing that there can be side effects).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The wrong variable (pc instead of r0) was used. Furthermore, someone
did cover this error by stupidly silencing the compiler warning that
occurred before a dummy void reference to r0 was added to the code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
When dumping over 100 registers (as on most ARM9 + ETM cores),
aid readability by splitting them into logical groups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The register names are perversely not documented as zero-indexed,
so rename them to match that convention. Also switch to lowercase
suffixes and infix numbering, matching ETB and EmbeddedICE usage.
Update docs to be a bit more accurate, especially regarding what
the "trigger" event can cause; and to split the issues into a few
more paragraphs, for clarity.
Make "configure" helptext point out that "oocd_trace" is prototype
hardware, not anything "real".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
XSVF improvements:
- Layer parts of XSVF directly over SVF, calling svf_add_statemove()
instead of expecting jtag_add_statemove() to conform to the SVF/XSVF
requirements (which it doesn't).
This should improve XSTATE handling a lot; it removes most users of
jtag_add_statemove(), and the comments about how it should really do
what svf_add_statemove() does.
- Update XSTATE logic to be a closer match to the XSVF spec. The main
open issue here is (still) that this implementation doesn't know how
to build and submit paths from single-state transitions ... but now
it will report that error case.
- Update the User's Guide to mention the two utility scripts for
working with XSVF, and to mention the five extension opcodes.
Handling of state transition paths is, overall, still a mess. I think
they should all be specified as paths not unlike SVF uses, and compiled
to the bitstrings later ... so that we can actually make sense of the
paths. (And see the extra clocks, detours through RUN, etc.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't add extra TCK in current state; exit from RESET had four extras.
Only IDLE --> IDLE needs such an extra clock. (At least one TCK must
be issued.)
Allow entry to RESET; SVF allows it, so must we (despite those entries
being commented out of the statemove table).
When entering RESET, always use TLR ... we might end up with extra clocks
in reset that way, which is harmless, but we'll never end up in any other
state than RESET, which is useful paranoia.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
As decided a while back, this isn't a transition we want to chance.
Whenever someone wants to got to RESET, force it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
SVF: comment the predefined/default paths; make them static const
SVF, XSVF: whitespace fixes, mostly so copyrights display sanely
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
After reading a bit further, it appears that ws2_32 (Windows Sockets 2)
is included in all versions of Windows and backwards compatible with
wsock32, at least according to
http://msdn.microsoft.com/en-us/library/ms740673%28VS.85%29.aspx.
Only Win95 seems to require a manual installation; is not a big deal.
So I think we can drop this whole business of detecting 64 bit MinGW and
just use -lws2_32 for all MinGW platforms.
Compilation on cygwin, using gcc v3 with option -mno-cygwin,
currently produces a large number of the following warnings:
warning: `gnu_printf' is an unrecognized format function type
These have been introduced with the recent MinGW GNU C99 printf
compliance patch, as gnu_printf was only introduced with gcc v4.4
and is not recognized with earlier versions.
The attached fix adds gcc version detection to the previous patch
to avoid the problem.
Passing "--std=gun99" is unfortunately not sufficient to make current
MinGW compilers conform with respect to checking printf format strings.
(The C runtime seems not to have problems.)
Fix by using a "gnu_printf" format specifier not "printf".
Use JIM_WIDE_MODIFIER for the sscanf format, and apply it for MINGW32 as
well as other Windows environments. (Microsoft doesn't conform to the
C99 standard, and uses "%I64d" not "%lld" for "long long".)
NB: __MINGW32__ should work on both w32 and w64,.
Generate a C struct with the data, and use that, instead of an
assembly language file. The assembly language causes issues on
Darwin and MS-Windows, which don't necessarily use GNU AS; or
if they do, don't necessarily use its ELF syntax.
It's also better in two other ways: fewer global symbols; and
the init-time size check gets optimized away at compile time.
(Unless it fails, in which case bigger chunks of the file vanish.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Based on some patches from <redirect.slash.nil@gmail.com>
for preliminary Win64 compilation. More such updates are
needed, but they need work. Compile tested on 64 and 32 bit
Linuxes, and Cygwin.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This makes the documentation a closer match to "help" output:
- "pathmove" somehow was not documented in the User's Guide
- "jtag_nsrst_assert_width" and "jtag_ntrst_assert_width"
are new; both needed descriptions.
- Removed two undocumented and fairly useless script mechanisms:
* production/production_info/production_test ... using it,
requires replacing everything; so having it adds no value.
* cpu ... way out of date; hopeless to keep that current
Note that anyone using that "production" stuff already defines
their own procedures, and can keep using them with no change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The LE check is obviously buggy (as easily triggered during some
testing), but I didn't audit the rest of the cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cleanup comments and layout/whitespace in the TMS tables.
Table contents stayed the same (ignoring whitespace).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a "FIX" comment; yes that was superfluous given that the
JTAG core does that check by default. It was also buggy since it
wrote to a stack frame that went away before the write happened!!
Other fixes: remove pointless malloc(); zero-init scan_field_t
values wherever they appear; whitespace scrub; spelling fix.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Load the XScale debug handler from the read-only data section
instead of from a separate file that can get lost or garbaged.
This eliminates installation and versioning issues, and also
speeds up reset handling a bit.
Plus some minor bits of cleanup related to loading that handler:
comments about just what this handler does, and check fault codes
while writing it into the mini-icache.
The only behavioral changes should be cleaner failure modes after
errors during handler loading, and being a bit faster.
NOTE: presumes GNU assembly syntax, with ".incbin"; and ELF,
because of the syntax of the ".size" directive.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Streamline/shrink some needless JTAG stuff:
- Use #defines for the JTAG instructions; they can't ever change
- Remove an unused (!) shadow of tap->ir_length
- Stop using a copy of target->tap
- Don't bother saving the variant after sanity checking ir_length
Also, make target_create() work as on other targets: build the
register cache later, making init_target() no longer be a NOP.
Handle malloc failure; remove a comment that was obsoleted by the
not-so-new target syntax.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove unused and deprecated (in the arch spec) mode for loading
code into the *main* icache (vs the "mini" icache). Disable some
extremely noisy (and rarely useful) low-level debug messages
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Declare almost everything as static.
Move stuff to remove most forward references.
Remove most forward declarations.
Warn if the unimplemented register functions get called.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Just fill out the rest of the cache line with NOPs; don't change
the record of how much data we consumed. Otherwise the count of
how much data is left can roll over from positive to negative
("VERY positive") and skip the loop termination of zero.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a header comment referencing useful XScale specs.
Make most data static, and the tables readonly.
Scrub extra blank lines.
Return fault codes from one routine.
Remove a needless NOP methood.
(BUGFIX) When we update R0, mark R0 as dirty/valid ... not R15/PC!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
We added two overridable procedures; document them, and the
two jtag arp_* operations they necessarily expose.
Update the comment about the jtag_init_reset() routine; it's
been obsolete for as long as it's had SRST support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This abstracts the "jtag arp_init-reset" call into a method
called from OpenOCD startup and reset processing.
Platforms which have different requirements for how such hard
resets must be performed can now override "init_reset" instead
of needing to rebuild custom hacked versions of the server.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Observed:
openocd: core.c:318: jtag_checks: Assertion `jtag_trst == 0' failed.
The issue was that nothing disabled background polling during calls
from the TCL shell to "jtag_reset 1 1". Fix by moving the existing
poll-disable mechanism to the JTAG layer where it belongs, and then
augmenting it to always pay attention to TRST and SRST.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Among other things this causes startup errors to kick in the
fallback "reset harder" logic during server startup. Comments
are also updated a bit, explaining what the various error paths
signify (in at least my observation).
There's one class of validation error that we can still plausibly
ignore: when wrong IDCODE values are observed.
This change seems to have helped make an OMAP5912 behave much
more reliably. There's still some post-reset flakiness, but
it's unrelated to scan verification.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Also, talk about "mainline" not "trunk".
The release.txt and release.sh files need more updates.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2825 b42882b7-edfa-0310-969c-e2dbd0fdcd60
At least some FT2232 based adapters don't necessarily come up
in the expected state, with SRST and TRST disabled. Since
other adapters could suffer the same problem, let's avoid
needing to patch every driver and just force *all* adapters
to initialize those values properly at server startup.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2824 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Instead of just assuming all IDCODE-deprived TAPs violate the
JTAG spec (they don't!), just require TAPs with such problems
to be declared with proper ircapture/irmask values. Example,
with mask and value of zero.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2823 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- revert to previous default: don't talk JTAG during SRST
- add "srst_nogates" flag, the converse of "srst_gates_jtag"
- with no args, display the current configuration
And update the User's Guide text with bullet lists to be a bit more clear.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2818 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- The guess-rev.sh script is now a tweaked version of "setlocalversion" as
seen in Linux, U-Boot, and various other projects. When it finds source
control support (git, hg, svn) it uses IDs from there. Else (specific
to this project) it reports itself as "-snapshot", e.g. from gitweb.
I verified this new "guess-rev.sh" script runs under Cygwin.
- Also update the generic version strings to be like "0.3.0-dev" (during
development) instead of the very long "0.3.0-in-development". These also
show up in the PDF docs. For better tracking, we might eventually change
these strings to include the version IDs too.
- Change the startup banner version strings so they include the guess-rev
output. Development and release versions with GIT will be like
Open On-Chip Debugger 0.3.0-dev-00282-g7191a4f-dirty (2009-10-05-20:57)
Open On-Chip Debugger 0.3.0 (2009-10-05-20:57)
instead of the previous SVN-specific (even when using git-svn!)
Open On-Chip Debugger 0.3.0-in-development (2009-10-05-01:39) svn:exported
Open On-Chip Debugger 0.3.0 (2009-10-05-01:39) Release
git-svn-id: svn://svn.berlios.de/openocd/trunk@2809 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Bugfix the error message so it shows the disliked value, and add
a debug message showing each TAP's IR capture value, all N bits.
This just changes diagnostics ... it still ignores the parameters
given to us at TAP declaration time.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2801 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The model is that this fires after scanchain verification, when it's
safe to call "jtag tapenable $TAPNAME". So it will fire as part of
non-error paths of "init" and "reset" command processing. However it
will *NOT* trigger during "jtag_reset" processing, which skips all
scan chain verification, or after verification errors.
ALSO:
- switch DaVinci chips to use this new mechanism
- log TAP activation/deactivation, since their IDCODEs aren't verified
- unify "enum jtag_event" scripted event notifications
- remove duplicative JTAG_TAP_EVENT_POST_RESET
git-svn-id: svn://svn.berlios.de/openocd/trunk@2800 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- don't needlessly export this function
- handle "case 0" debug method-of-entry better (silent by default)
The "case 0" is a valid debug entry mode so it doesn't deserve the
warning int now gets. But it probably means that OpenOCD confused
itself somehow; or that it confused the ARM9EJS target.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2799 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- ETB
* report _actual_ hardware status, not just expected status
* add a missing diagnostic on a potential ETB setup error
* prefix any diagnostics with "ETB"
- ETM
* make "etm status" show ETM hardware status too, instead of
just traceport status (which previously was fake, sigh)
- Docs
* flesh out "etm tracemode" docs a bit
* clarify "etm status" ... previously it was traceport status
* explain "etm trigger_percent" as a *traceport* option
ETM+ETB tracing still isn't behaving, but now I can see that part of
the reason is that the ETB turns itself off almost immediately after
being enabled, and before collecting any data.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2790 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Don't issue needless JTAG resets ... only do them after
errors. Normal exit now leaves every TAP in BYPASS.
- Fix an unlikely memory leak on one fault path.
- Remove the oddball limitation that invalid capture LSBs
trigger errors only for TAPs that support IDCODE.
Re the JTAG reset: there are too many of them, and they can
(and do!) change system state. So the needless ones should
get removed. This one was especially pointless.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2777 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Commands were supposed to have been "arm11 memwrite ..."
not "memwrite ..."
- Get rid of obfuscatory macros
- Re-alphabetize
- Add docs for "arm11 vcr"
git-svn-id: svn://svn.berlios.de/openocd/trunk@2776 b42882b7-edfa-0310-969c-e2dbd0fdcd60
When the OpenOCD server starts up it records its state as TAP_RESET,
even though it could be anything. Then when it starts to examine
the scan chain, it calls jtag_add_tlr() which sees it doesn't have
any work to do, and so it does nothing. This can make the next
operations fail because they start from the wrong TAP state...
Instead of caring about the current recorded state, always enter
TAP_RESET by forcing five clocks with TMS high.
(NOTE: it seems most other JTAG adapter drivers have this same bug.)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2763 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Change the handling of the "-ircapture" and "-irmask" parameters
to be slightly more sensible, given that the JTAG spec describes
what is required, and that we already require that conformance in
one place. IR scan returns some bitstring with LSBs "01".
- First, provide and use default values that satisfy the IEEE spec.
Existing TAP configs will override the defaults, but those parms
are no longer required.
- Second, warn if any TAP gets set up to violate the JTAG spec.
It's likely a bug, but maybe not; else this should be an error.
Improve the related diagnostics to say which TAP is affected.
And associated minor fixes/cleanups to comments and diagnostics.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2758 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Ready for discussion and tiny patches that tries out this scheme.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2755 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Added gdb_sync feature that allows GDB to sync up to target state.
Issue "monitor gdb_sync" and the next stepi, will return immediately
with updated register values to GDB.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2754 b42882b7-edfa-0310-969c-e2dbd0fdcd60
make sure that when there are two or more targets, their
various pre/post event reports are correctly ordered.
Previously, only the first target always saw its "pre"
method before SRST was asserted or deasserted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2753 b42882b7-edfa-0310-969c-e2dbd0fdcd60
only expose the registers which are actually present. They
could be missing for two basic reasons:
- This version might not support them at all; e.g. ETMv1.1
doesn't have some control/status registers. (My sample of
ARM9 boards shows all with ETMv1.3 support, FWIW.)
- The configuration on this chip may not populate as many
registers as possible; e.g. only two data value comparators
instead of eight.
Includes a bugfix in the "etm info" command: only one of the
two registers is missing on older silicon, so show the first
one before bailing.
Update ETM usage docs to explain that those registers need to be
written to configure what is traced, and that some ETM configs
are not yet handled. Also, give some examples of the kinds of
constrained trace which could be arranged.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2752 b42882b7-edfa-0310-969c-e2dbd0fdcd60
system, removes 20 non-existent registers ... but still includes
over 45 (!) ETM registers which don't even exist there ...
- Integrate the various tables to get one struct per register
- Get rid of needless per-register dynamic allocation
- Double check list of registers:
* Remove sixteen (!) non-registers for data comparators
* Remove four registers that imply newer ETM than we support
* Change some names to match current architecture specs
- Handle more register info
* some are write-only
* some are read-only
* record which versions have them, just in case
- Reorganize the registers to facilitate removing the extras
* group e.g. comparator/counter #N registers together
* add and use lookup-by-ID
git-svn-id: svn://svn.berlios.de/openocd/trunk@2751 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Add a header comment
- Line up the ETM context struct, pack it a bit
- Remove unused context_id (this doesn't support ETMv2 yet)
- Make most functions static
- Remove unused string table and other needless lines of code
- Correct "tracemode" helptext
Also provide and use an etm_reg_lookup() to find entries in the ETM
register cache. This will help cope with corrected contents of that
cache, which doesn't include entires for non-existent registers.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2750 b42882b7-edfa-0310-969c-e2dbd0fdcd60
didn't turn up earlier. Is everyone still using gcc 3.x? Or is the x86
version of gcc 4.x much more relaxed?
git-svn-id: svn://svn.berlios.de/openocd/trunk@2749 b42882b7-edfa-0310-969c-e2dbd0fdcd60
of a (NOR) flash chip: allow passing "last" as an alias
for the number of the last sector.
Improve several aspects of error checking while we're at it.
From: Johnny Halfmoon <jhalfmoon@milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2746 b42882b7-edfa-0310-969c-e2dbd0fdcd60
garbage after the expected data (from the TAPs' BYPASS or IDCODE
registers).
NOTE that there was previously some code that looked like it was
trying to do this ... which didn't work, because it was looping
over the list of expected TAPs, and never checked *after* that
list completed! That could hide some *nasty* reset issues...
Also replace a now-obsolete scanchain length test with one that
behaves correctly; and update reporting of unexpected IDCODEs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2739 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch modifies an error message which, in its original state,
I find somewhat unhelpful. So a small hint was added.
Signed-off-by: Johnny Halfmoon <jhalfmoon at milksnot.com>
git-svn-id: svn://svn.berlios.de/openocd/trunk@2738 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Shrink messaging during resets, primarily by getting rid of
"nothing happened" noise that hides *useful* information.
- Improve: the "no IDCODE" message by identifying which tap only
supports BYPASS; and the TAP event strings.
Related minor code updates:
- Remove two needless tests when examining the chain: we know
we have a TAP, and that all TAPs have names.
- Clean up two loops, turning "while"s into "for"s which better
show what's actually being done.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2736 b42882b7-edfa-0310-969c-e2dbd0fdcd60
for disabling TAPs. We don't actually know how to make any
JRCs which do that yet; but when we do, this will matter.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2735 b42882b7-edfa-0310-969c-e2dbd0fdcd60
and Tcl/external):
- Reorder so *both* paths (TCK/TMS or TRST) can enable TAPs with
ICEpick ... first C code flags TAPs that got disabled, then call
any Tcl code that might want to re-enable them.
- Always call the C/internal handlers when JTAG operations can be
issued; previously that wasn't done when TRST was used.
Plus some small cleanups (whitespace, strings, better messaging
during debug and on some errors) to reset-related code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2730 b42882b7-edfa-0310-969c-e2dbd0fdcd60
avoid a duplicate test.
Plus other cleanup in the same code: be "static", sane line lengths
for source and diagnostics, and fix misleading variable names.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2725 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Erase logic:
- command invocation
+ treat "nand erase N" (no offset/length) as "erase whole chip N"
+ catch a few more bogus parameter cases, like length == 0 (sigh)
- nand_erase() should be static
- on error
+ say which block failed, and if it was a bad block
+ don't give up after the first error; try to erase the rest
- on success, say which nand device was erased (name isn't unique)
Device list ("nand list"):
- say how many blocks there are
- split summary into two lines
- give example in the docs
Doc tweaks:
- Use @option{...} for DaVinci's supported hardware ECC options
For the record, I've observed that _sometimes_ erasing bad blocks causes
failure reports, and that manufacturer bad block markers aren't always
erasable (even when erasing their blocks doesn't trigger an error report).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2724 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- update comments to say so.
- update docs to clarify that the "arm9tdmi" command prefix
is a misnomer.
- bugfix some messages that wrongly assume only ARM9TDMI
based processors use this code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2719 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Cleanup some the downloaded ARM target algorithm code:
- Provide more complete disassembly of the DCC bulk write code
- Make code blocks "static const", in case GCC doesn't
- Fix some tabbing/layout issues
- Make some arm7_9_common.h flags be "bool" not "int"; and compact
the layout a bit (group most bools together)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2698 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch adds target algorithm support for those flash devices that do not support DQ5 polling. So far they could only be programmed with host algorithm, but this was way too slow.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2682 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Infinite loop bugfix when running tap configure a second time
git-svn-id: svn://svn.berlios.de/openocd/trunk@2681 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Optionally shave time off the armv4_5 run_algorithm() code: let
them terminate using software breakpoints, avoiding roundtrips
to manage hardware ones.
Enable this by using BKPT to terminate execution instead of "branch
to here" loops. Then pass zero as the exit address, except when
running on an ARMv4 core. ARM7TDMI, ARM9TDMI, and derived cores
now set a flag saying they're ARMv4.
Use that mechanism in arm_nandwrite(), for about 3% speedup on a
DaVinci ARM926 core; not huge, but it helps. Some other algorithms
could use this too (mostly flavors of flash operation).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2680 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Provide an "armv7a disassemble" command. Current omissions include
VFP (except as coprocessor instructions), Neon, and various Thumb2
opcodes that are not available in ARMv7-M processors.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2676 b42882b7-edfa-0310-969c-e2dbd0fdcd60
lean up some loose ends with the ARM disassembler
- Add a header comment describing its current state and uses
and referencing the now-generally-available V7 arch spec
- Support some mode switch instructions:
* Thumb to Jazelle (BXJ)
* Thumb to ThumbEE (ENTERX)
* ThumbEE to Thumb (LEAVEX)
- Improve that recent warning fix (and associated whitespace goof)
- Declare the rest of the internal code and data "static". A
compiler may use this, and it helps clarify the scope of these
routines (e.g. what changes to them could affect).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2675 b42882b7-edfa-0310-969c-e2dbd0fdcd60
David Brownell
Franck HÉRÉSON
Nicolas Pitre
Oleg Seiljus
Michael Roth
Øyvind Harboe
Zachary T Welch
Redirect 'Slash' NIL
oyvind
David Brownell
Lennert Buytenhek
Yauheni Kaliuta
dbrownell
oharboe
mlu
ntfreak