When it doesn't do anything (most of the time) it has negligible
performance impact. With slower remote bitbang, and multiple spike
instances being tested in a single chain, things are sufficiently slow
that if a computer is busy then this is required to pass
riscv-tests/debug.
Change-Id: I8816efedaa0cc3b25734ba8fdc979ee4502284a1
Signed-off-by: Tim Newsome <tim@sifive.com>
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This makes the messages consistent with most of the rest of
the OpenOCD output.
Change-Id: I915a01187e7fc317e02483ac0bbd39ec077d6321
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6274
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Initial support for Renesas RZ/G2 MPU family
Change-Id: I5ca74cddfd0c105a5307de56c3ade7084f9c28d2
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6250
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Made sure that also outgoing GDB packets are logged,
not only the incoming ones.
- Improved the treatment of non-printable characters
in the packets to make it more robust.
Prior to this change:
- Outgoing packets were not printed unless OpenOCD was
re-compiled with _DEBUG_GDB_IO_.
- Non-prinable characters were only treated in incoming
'X' packets.
After this change:
- Both incoming and outgoing GDB packets are logged
on debug_level >= 3, so that both directions of the
GDB channel are visible.
- Non-printable characters are checked for in every packet
so that hey do not interfere with the terminal.
Change-Id: I0613e57ae5059b3279b0abcb71276cf5719a8699
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6269
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The special .DELETE_ON_ERROR deletes the target file on recipe error.
Otherwise, an incomplete output file may be considered up to date
the next time around. .DELETE_ON_ERROR provides reasonable
protection at virtually no cost.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: I67dca47ae5ddf3786993c87b9991b3046a85f00b
Reviewed-on: http://openocd.zylin.com/6235
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Without such reference, it could be difficult to find the example.
Change-Id: Ia9ffb06bc1a45446c2c7b53197ab3400e1d8a9e9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6281
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Main improvement is in the doxygen comments.
Minimize the delta with kernel file.
Skip the functions hlist_unhashed_lockless() and
__list_del_clearprev() that are relevant only in kernel.
Remove gcc extension "omitted conditional operand".
Change-Id: I2e9ddb54cfe2fa5f7cf18f44726acd144e1f98b9
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6276
Reviewed-by: <rdiezmail-openocd@yahoo.de>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Current autocomplete filters-out some command reported by "info
commands". One of the filter rule concerns the command's private
data.
Every command registered by OpenOCD has its 'struct command' as
private data.
By ignoring commands without private data, we loose several TCL
commands registered by jimtcl, e.g. 'foreach', 'llength'.
By assuming that every command with non-NULL private data has
'struct command' as private data, we risk at best to access
inconsistent data, at worst to trigger a segmentation fault.
Export the already available functions:
- to check if a command has been registered by OpenOCD and
- to get the private data.
While there, rename jimcmd_is_ocd_command() as
jimcmd_is_oocd_command().
Don't filter-out jimtcl commands with no private data.
Check the private data only on OpenOCD commands.
Change-Id: Ib5bf8d2bc5c12440c0cfae438f637c38724a79b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6282
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
The helper jim-nvp does not comply with OpenOCD coding style due
to typedef of struct and CamelCase symbol names.
While it's trivial fixing the helper and all its current use in
the code, changing these APIs will potentially break a number of
patches pending in gerrit. Gerrit will not trigger any alert, but
the code will generate compile error after the merge.
Add the compile flag "-Wno-error=deprecated-declarations" to keep
as warning (not as error) the use of "deprecated" functions and
types.
Rename all the CamelCase symbols is lowercase and provide struct
prototypes in place of the typedef.
Add a DEPRECATED section to 'jim-nvp.h' where the old CamelCase
symbols and the old typedef are re-declared with compile attribute
'deprecated'.
With this change OpenOCD compiles, but generates warnings.
The remaining changes allover OpenOCD code will be fixed in a
separate patch for easier review.
The patches merged later that still use the old deprecated API
will compile with warnings. This will permit to identify and fix
these cases.
Change-Id: I786385d0f662dbb1be5be313ae42623156d68ce5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6183
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The memory allocated to hold the watchpoints is not freed at
OpenOCD exit.
Free the watchpoint memory at OpenOCD exit.
Change-Id: I518c9ce0dc901cde2913d752e3154734f878b854
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6210
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Use byte address select for 1 and 2 bytes length.
Use normal mode for 4 bytes length.
Change-Id: I28d182f25145d0635de64d0361d456f1ad96640e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6197
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Decrement the available watchpoints only when succeed setting it.
Initialize the available watchpoint with the correct value.
Change-Id: I0f93b347300b8ebedbcd9e718d4ba32b26cf6846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6196
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The current implementation of OpenOCD does not support watchpoints for
cortex_a architecture. So, I replaced the add_watchpoint and
remove_watchpoint with the specific implementation for the
cortex a and using the breakpoint implementation and the arm
documentation [1] as reference. In particular, I have made the
following changes:
* added the following functions
- cortex_a_add_watchpoint
This wrapper function check whether there are any watchpoint
available on the target device by calling cortex_a_set_watchpoint.
- cortex_a_set_watchpoint
This function is responsible for settings the watchpoint register
pair. In particular, it sets the WVR and the WCR registers with
the cortex_a_dap command.
- cortex_a_remove_watchpoint
This wrapper function the selected watchpoint on the target device
by calling cortex_a_unset_watchpoint.
- cortex_a_unset_watchpoint
This function sets both the WVR and the WCR registers to zero, thus
unsetting the watchpoint.
[1]
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0464f/BCGDHIEJ.html
Change-Id: I86611dab474cb84836662af572b17636dc68e282
Signed-off-by: Chengyu Zheng <chengyu.zheng@polimi.it>
Reviewed-on: http://openocd.zylin.com/3913
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
When a WAIT occurs the commands after the WAIT are replayed and the
STICKYORUN is cleared. However if another WAIT occurs during the
command replay, the command itself is resent but the STICKYORUN bit
shall also be cleared. If this is not done, the MEM-AP hangs.
Change-Id: I14e8340cd5d8f58f4de31509da96cfa2ecb630d1
Signed-off-by: micbis <michele.bisogno.ct@renesas.com>
Reviewed-on: http://openocd.zylin.com/6278
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The corresponding bit for each macro is changed, but this is not
relevant in the code.
Change-Id: I7039464f5a3d55d008208f44952aadeb815bd5a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6212
Tested-by: jenkins
Add the full text of the MIT license to the kernel tree. It was copied
directly from:
https://spdx.org/licenses/MIT.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I94a5dea5ced6421809ea2a3448f8dda19a93f5c9
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6219
Tested-by: jenkins
The implementation of command 'usage' is broken while checking the
line limit of 76 chars per line (e.g. 'usage load_image') and the
line wrapping is not correct. The same broken code is used for the
first output line of command 'help' too.
When call command_help_show_wrap(), include the command's name in
the string so the whole text would be wrapped.
Change-Id: Idece01ce54994db7e851d8522435ff764b11f3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6223
Tested-by: jenkins
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
There are still few adapter_khz, ftdi_location, jtag_nsrst_delay
and xds110_serial strolling around ...
Change-Id: I3e8503dcc3875e3c92e6536f3d455a5e448d51ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6270
Tested-by: jenkins
Use the existing macro ARRAY_SIZE().
Rewrite the functions rtos_type.create() to simplify the logic.
Change-Id: I8833354767045d1642801d26944c9087a77add00
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6261
Tested-by: jenkins
There are still few cases where the macro ARRAY_SIZE() should be
used in place of custom code.
Use ARRAY_SIZE() whenever possible.
Change-Id: Iba0127a02357bc704fe639e08562a4f9aa7011df
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6260
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Replace the custom macro dimof() with the OpenOCD macro
ARRAY_SIZE().
Change-Id: I2fe638444f6c16f2a78c1fd558b21550f76282d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6259
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Simplify the code and prevent some field of the instruction from overflowing
Change-Id: I0acade05ad351d0e1918be4b75702b1637aa02c9
Signed-off-by: Xiang W <wxjstz@126.com>
Just use regular lists in FreeRTOS.c. O(n) lookups should be fine.
Change-Id: I5dc7b2fd209e0214a87d73bd6c4b63fd664bf49a
Signed-off-by: Tim Newsome <tim@sifive.com>
The Xilinx Zynq UltraScale+ SoC have an "AXI-AP" access port for direct memory accesses without halting CPUs.
Change-Id: I6303331c217795657575de4759444938e775dee1
Signed-off-by: Olivier DANET <odanet@caramail.com>
Reviewed-on: http://openocd.zylin.com/6263
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD already defines the macro ARRAY_SIZE, while riscv code
uses a local macro DIM.
Prefer using the macro ARRAY_SIZE() instead of DIM().
Not all the riscv code has been upstreamed, yes; this patch only
covers the code already upstreamed.
Change-Id: I89a58a6d91916d85c53ba5e4091b558271f8d618
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6258
Reviewed-by: Xiang W <wxjstz@126.com>
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The array newly_halted[] is assigned but its value is never used.
Drop it!
Change-Id: I678812a31c45a3ec03716e3eee6a30b8e8947926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6257
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
The target mem_ap appears as an ARM target, thus it allows the
execution of ARM specific commands causing the crash of OpenOCD.
E.g. 'arm mrc ...' can be executed and segfaults.
Replace the incorrect ARM magic number with a dedicated one.
While there, remove the 'struct arm', that is now holding only the
mem_ap's dap, and replace it with a pointer to the dap.
Change-Id: I881332d3fdf8d8f8271b8711607737b052a5699b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6213
Tested-by: jenkins
Commit e216186fab ("helper/command: register full-name commands
in jim") and commit a7d68878e4 ("helper/command: unregister
commands through their full-name") introduce a LOG_DEBUG() message
each for command registration and unregistration.
The messages above are quite noisy and pollute the log when
debug_level is 3 or higher.
They can be useful to debug the command registration logic, but
for the other debug activities on OpenOCD are just noisy.
Already commit a03ac1ba30 ("helper/command: disable logging of
registered commands [RFC]") was merged to silent the first case
that is now back with additional logs.
Silent both log messages.
Use 'if (false)' to silent them, making easy to re-enable it when
or if someone needs it.
Change-Id: Id8a067e60e822d4ecbddcb036d081298f7e6181f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6220
Tested-by: jenkins
Autoconf generates several files in root folder of the project.
Keep the root folder cleaner by specifying subfolder 'build-aux'.
Align .gitignore accordingly.
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Change-Id: Ied87faba495d9eeb8f98e78c2e2b7e7e596febfb
Reviewed-on: http://openocd.zylin.com/6236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
They are at least since Autoconf 2.67 present,
and we are requiring version 2.69.
Change-Id: I41b33d4ebe02198f03cdddcc4a3c1beedd993d78
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6239
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Preprocessor directives like "#if SYMBOL" silently replace undefined or
misspelt symbols with 0, which makes configuration bugs hard to spot.
Compiler flag "-Wundef" prevents such errors.
Change-Id: I91b7ba2db02ef0c3c452d334601c53aebda4660e
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: http://openocd.zylin.com/6238
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I101c76a638805d77c1ff356cf0f027552389e5d3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6216
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: Ia5f134c91beb483fd865df9e4877e0ec3e789478
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6215
Tested-by: jenkins
Tim Newsome
Jan Matyas
Marc Schink
R. Diez
Adrian Negreanu
micbis
Jan Matyas
Tarek BOCHKATI
Antonio Borneo
Andreas Fritiofson
Chengyu Zheng
Thomas Gleixner
Xiang W
Olivier DANET