It was fixed by e94180571 ("at91sam9: factorise cpu support") in 2011.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change-Id: I95ea149b45a9902424bf9068b4a2830c17ddc6be
Reviewed-on: https://review.openocd.org/c/openocd/+/7525
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
in raspberrypi-native.cfg
Fixes: bec6c0eb09 (tcl/interface: universal config for all Raspberry Pi models)
Signed-off-by: Tomas Deingruber <Deingruber.Tomas@gmail.com>
Change-Id: I632c8acd84974937849b5fdf2943239def17bd6d
Reviewed-on: https://review.openocd.org/c/openocd/+/7512
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Integrate a rescue mode inspired by [1].
The current OpenOCD must be restarted before normal work with the RP2040
because the rescue debug port must not be activated (or the target
is reset every 'dap init'). To continue without restarting OpenOCD
we would need to switch off the configured rescue dap.
Change-Id: Ia05b960f06747063550c166e461939d92e232830
Link: [1] https://github.com/raspberrypi/openocd/blob/rp2040/tcl/target/rp2040-rescue.cfg
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7327
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Speed calibration coeffs are computed from cpufreq/scaling_max_freq
and from the device-tree compatibility information.
Raspberry Pi linux offers /dev/gpiomem for non-root access
to the GPIO registers since ~2016.
Do not configure 'bcm2835gpio peripheral_base' as it is necessary
only if /dev/mem is used - it requires running OpenOCD as root
- it's a security risk so it should be avoided.
The configuration of the GPIO connector (40-pin header)
is factored out and ready to use in interface configuration
for other driver (e.g. linux gpiod).
Mark raspberrypi2-native.cfg as deprecated and redirect
it to raspberrypi-native.cfg
Change-Id: Icce856fb660b45374e94174da279feb51f529908
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7264
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Same mechanism as in stm32f1x.cfg reused here.
Change-Id: I81f02feb2b655e8259341b22180f3a8b82e28d05
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7438
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The rtos hwthread has been merged in 2019 with commit 85ba2dc4c6
("rtos/hwthread: add hardware-thread pseudo rtos").
During review in patchset 19 the name of the rtos has been changed
from 'hawt' to 'hwthread'.
Some target config file was already merged ready for hwthread, but
keeping the relevant lines commented and still reporting the old
name.
Enable rtos hwtread to the target that were supposed to use it.
Fix the name of the rtos.
Change-Id: I877862dcdba39f26462bb542bac06d1a5f5f222d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7384
Tested-by: jenkins
This patch is picked from the tcl part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support the communication with Nuvoton's Cortex-M4 chips: M541 &
NUC442/472 series.
This patch has been tested with Nuvoton's NuTiny-SDK-NUC472 development
board [2].
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
[2]: https://www.nuvoton.com/export/resource-files/UM_NuTiny-SDK-
NUC472_EN_Rev1.02.pdf
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I27ac58dd1c98a76e791a4f1117c31060cf5522e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7330
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
rp2040-core0.cfg configuration file was intended for a special adapter
which selects a SWD multidrop target on its own. This means
that rp2040-core0.cfg is totally unusable with a standard SWD
adapter. The file was marked as deprecated in 0.12 release.
The reworked rp2040.cfg can be restricted to use just one core:
openocd ... -c 'set USE_CORE 0' -f target/rp2040.cfg
Remove the obsoleted config.
Change-Id: Id886471622bb4a8cb83f5c4c3660657407aaaf74
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7326
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add the variable selected configuration for SMP debug with rtos hwthread.
Use SMP by default.
Change-Id: I1c37d91688a3ab58d65c15686737892965711adc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7242
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.
To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.
Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
instrument "target/stm32x5x_common.cfg" used by both STM32L5x/U5x
to support HLA adapters like "interface/stlink.cfg" in non-secure mode
if the device switches to secure mode, the debug session will be
stopped immediately (with an explanatory message).
Change-Id: I645fdd55e3448ef82d0ddcc396f42fd7b2f39ac3
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reported-by: Patrik Bachan <diggit@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/317/
Reviewed-on: https://review.openocd.org/c/openocd/+/6546
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Some config changes required to run ESP32-S3 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I38022bb5ff5830e1cf9d11d6fe795ea99d91e9db
Reviewed-on: https://review.openocd.org/c/openocd/+/7254
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some config changes required to run ESP32-S2 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: Ie0a742442254ec6e95d4e05be40213b079a94dab
Reviewed-on: https://review.openocd.org/c/openocd/+/7253
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some config changes required to run ESP32 with full feature set
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I484324f8497ec7934bb73164c638fc5f6460fcc4
Reviewed-on: https://review.openocd.org/c/openocd/+/7252
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The work area should be backed up.
The flash probe runs an algorithm on the target CPU.
The flash is probed during gdb connect if gdb_memory_map is enabled
(is enabled by default).
Without backup the target memory gets corrupted on gdb connect.
Change-Id: I3344b9dc6cbf904d49f3b05ab104b541d1d63422
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7257
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Since all the device definition when accessing device from jtag is also
valid when accessing from swd, lets make sure the configuration can
handle the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5af071137fd8c3b52cc4ef72401f8eba952f9cad
Reviewed-on: https://review.openocd.org/c/openocd/+/7090
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The STM32L5 and U5 devices have DBGMCU_CR trace related bits changed
wrt other STM32 devices.
Fix the setting in configuration script.
Change-Id: I0bbc48e7b1290b603c6966cf5ddd42df389e6ede
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7117
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
- Config files for DAP/JTAG and DAP/SWD systems
- Xtensa core config definitions for NXP RT685 with Xtensa HiFi DSP
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I9c3280052073d86e09c7553de661eb8662a95c4a
Reviewed-on: https://review.openocd.org/c/openocd/+/7145
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While reviewing on gerrit the change
https://review.openocd.org/6932/
it get clear that the missing documentation on stm32f4x's code
was triggering errors in the new change.
OpenOCD is currently unable to read traces, but these can be
hopefully be read with some other tool.
Document the settings for enabling trace on stm32[fl]4x.
Change-Id: Ibae77a53de16375d3d500e728678740095547009
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6945
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With commit dc7b32ea4a ("armv7m_trace: get rid of the old tpiu
code") the target's event "trace-config" has been deprecated.
Create the TPIU device.
Replace the target's event "trace-config" with tpiu's event
"pre-enable" in the STM32 devices that require enabling the trace
clock _before_ programming the TPIU.
Make the script multi-instance-able in case it's used for JTAG
chained devices.
Uniform the code in STM32F4x with the other scripts.
Remove the empty event from STM32WLx.
Change-Id: Ifda219c3c5f37e03072a88168611cf505eb630b7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
linuxgpiod driver.
Adds support for drive mode and resistor pull options on all signals.
Change-Id: Ic90cb4f06db82435294228b6793330107a9f3606
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
am335xgpio driver. The AM335x has 4 GPIO 'chips' (chip number 0-3
inclusive), with each one providing 32 GPIOs (gpio_num 0-31 inclusive).
Change-Id: I7c63c0e4763657ea51790c43fc40d32b7c3580bb
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6984
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch adds support for DAP interface to Cadence vdebug driver.
It implements a new transport layer for dapdirect_swd.
Change-Id: I64b02a9e1ce91e552e07fca692879655496f88b6
Signed-off-by: Jacek Wuwer <jacekmw8@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6965
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This driver is used with the ESP32 chips which has builtin USB-JTAG
interface. e.g. with ESP32-C3, ESP32-S3
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61
Reviewed-on: https://review.openocd.org/c/openocd/+/6943
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ief3da306a6e1978de7dfb8f552f9ff23151f9944
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7030
Tested-by: jenkins
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/interface | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7bd6a628e9e153fc477cddf9b97087a39ec48aa7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7029
Tested-by: jenkins
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/board | while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: Ibcf7da62e842aafd036a78db9ea2b9f11f79af16
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7028
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
For historical reasons, no license information was added to the
tcl files. This makes trivial adding the SPDX tag through script:
fgrep -rL SPDX tcl/ target| while read a;do \
sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n
}' $a;done
With no specific license information from the author, let's extend
the OpenOCD project license GPL-2.0-or-later to the files.
Change-Id: I7b2610300b24cccd07bfa6fb5f1266970d5d3a1b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7027
Tested-by: jenkins
The SPDX tag is aimed at machine handling and it's thus expected
to be placed in the first line.
Change-Id: I3992856eeb28b333c38d010ef286e22471ede263
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7026
Tested-by: jenkins
OpenOCD project is switching to SPDX tags.
Replace the few FSF boilerplate in tcl folder.
Change-Id: I15b146eb77cc491ed7355178f684f3e76fc763b4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7025
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Wolfram Sang
Tomas Deingruber
Tomas Vanek
Andreas Fritiofson
Antonio Borneo
Zale Yu
Kyle Schwarz
Rocco Marco Guglielmi
George Voicu
Tarek BOCHKATI
Erhan Kurubas
Nishanth Menon
Paul Fertser
Steve Marple
Ian Thompson
Toms Stūrmanis
Jae Hyun Yoo
Jacek Wuwer
Adrien Grassein