Commit 246782229f ("smp: replace commands smp_on/smp_off with
"smp [on|off]"") deprecates some multi-word comments, when openocd
was unable to properly handle mixes of multi-word commands and tcl
procedures having a common initial word.
This limitation is over, so move in startup.tcl the multi-word
commands deprecation, making it easy to remove them after a grace
period.
Change-Id: Icb550d1fa7559b95692d2a1244880da6c90ec0b2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5677
Tested-by: jenkins
Windows socket descriptor is not file descriptor, so when
using remote_bitbang on Windows, it fails with "fdopen:
failed to open write stream".
This patch removes the file write stream, replaces it
with socket write calls.
Change-Id: Ifd7c8a4139a5ac51ecd2846835a7a947a90fe16c
Signed-off-by: Yun Liu <liuyun.97@gmail.com>
Reviewed-on: http://openocd.zylin.com/6096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Chip is similar to imx8x series but has different cores at different
addresses.
Support for reduced versions is not yet available.
Tested on imx8qm-mek board
Change-Id: Ia34a80d561ab2849a570d8c375b936a45cbf45ca
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-on: http://openocd.zylin.com/5042
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some CMSIS-DAP adapters keep buffered packets over
USB close/open so we need to flush up to 64 old packets
to be sure all buffers are empty.
Flush just after cmsis_dap_open() and in the case of command mismatch.
Change-Id: If21a118639e64d90635b4ecf81013d29a7b9f78d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6135
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Check returned HID report number (or the first byte of returned
bulk packet) which should be equal to the issued command or 0xff
in case of the command is not implemented.
Fix error return paths in cmsis_dap_init() to clean up the adapter
connection.
Don't fail cmsis_dap_init() when an unimportant function fails
(for the case the adapter doesn't implement some parts of protocol).
Change-Id: Ief8382aabe9915346b2273702fb2ff17bbb5eb1b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6121
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
The function's name was consistent with its purpose to handle
commands that were not at root level, thus not directly 'known'
by jimtcl.
Rename it as jim_command_dispatch() to highlight that now it is
a jim_handler and its purpose is to dispatch the call to the
proper command handler.
Change-Id: I9491a6d6459b8eb37a6c402abcae08388c693764
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5791
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that all commands are executed through the common handler
command_unknown(), the message about command execution is logged
by command_unknown(). There is no need, for "native" commands
(.jim_handler) at root level to log the message (again) by itself.
Remove calls to script_debug() apart from command_unknown().
Make script_debug() static as only used in command.c.
Change-Id: I9b2728b69e7643d6121c4b35a96bc825bcb5488d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5676
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
There is no need anymore to keep alive the tree of struct command.
Remove it and let jim to free() the command's struct command that
is referenced through command's private data.
Change-Id: I2cd84e0274a969ce200320e3a177ac20c7823da0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5675
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While keeping the struct command in place, unregister the jim
commands by scanning the list of jim commands through their
full-name.
Change-Id: I0e903fbc31172858b703d67ccd471809c7949e86
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5674
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that every command has struct command as private data, use jim
to get access to the struct command to read the command mode,
instead of running through the tree of struct command.
Change-Id: Iddacdbac604714f6abe38a050daad245bdcfd20c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5673
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that the commands are registered using their full-name, the
full-name is in argv[0].
Don't rebuild the full-name but use directly argv[0].
Change-Id: Ic9e469ac39276367b8c47527e70791ff470fefbc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5672
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While still keeping the tree of struct command, stop registering
commands in jim by the root "word" only.
Register the full-name of the command and pass as private data the
struct command of the command itself.
Still use the tree of struct command to un-register the commands.
Some "native" commands (.jim_handler) share the same handler, then
the handler checks the command name to run the right code.
Now argv[0] returns the full-name of the command, so check the
name by looking in the struct command passed as private data.
Change-Id: I5623c61cceee8a75f5d5a551ef3fbf5a303af6be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5671
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The current implementation of "help" related commands is tightly
connected to the tree of struct command.
The TCL commands 'add_usage_text' and 'add_help_text' have to add
fake commands in the tree of struct command to handle the help of
TCL procs.
Move all the help texts in a list accessible from the struct
command_context and register the commands through their full name.
Keep the list sorted alphabetically by the command name, so the
result of commands 'help' and 'usage' will be sorted too.
Remove the associated help and usage during commands un-register,
but call help_del_all_commands() for the text added through TCL
commands 'add_usage_text' and 'add_help_text'.
The resulting help and usage output is not changed by this patch
(tested on all the help and usage strings in current master
branch).
Change-Id: Ifd37bb5bd374cba1a22cd7aac208505b4ae1e6fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5670
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A tcl proc can be executed anytime, in any command mode.
Let the command "command mode" to detect a tcl proc and return the
string "any".
Change-Id: I0559076c3063632ee0ea9a57a25f91060209b77f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5669
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Replace the "struct command *parent" parameter with a string that
contains the command prefix.
This abstracts the openocd code from the knowledge of the tree of
struct command.
This also makes unused the function command_find_in_context(), so
remove it.
Change-Id: I598d60719cfdc1811ee6f6edfff8a116f82c7ed6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5668
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In current code the current target is overridden whenever
jim_handler_data is not NULL. This happens not only with target
prefixed commands, but also with cti, dap and swo/tpiu prefixed
commands.
While this is not causing any run-time issue, by now, the
behaviour is tricky and makes the code cryptic.
Add a specific field to struct command for the target override so
the content of jim_handler_data can be restricted to command
specific data only (today only cti, dap and swo/tpiu).
Extend the API register_commands() to specify the presence of
either the command data or the override target.
The new API makes obsolete calling command_set_handler_data() to
set jim_handler_data, so remove it.
Change-Id: Icc323faf754b0546a72208f90abd9e68ff2ef52f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5667
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that target override is uniformly implemented for all types of
commands, there is no need for target-prefixed "native" commands
(.jim_handler) to sneakily extract the overridden target from the
struct command.
Modify the commands to use the standard API get_current_target().
Change-Id: I732a09c3261e56524edd5217634fa409eb97a8c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5666
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Today openocd registers the commands to jim with three methods:
1) "native" commands (.jim_handler) at root level are registered
directly as jim commands;
2) "simple" commands (.handler) at root level are registered
through the handler script_command();
3) all other commands not at root level are registered through the
handler command_unknown().
Apart from using different handler, other inconsistencies are
present:
a) command in 1) are not checked for their "mode", so are run with
no check about current mode (COMMAND_CONFIG or COMMAND_EXEC);
b) target_call_timer_callbacks_now() is called only for "simple"
commands and not for "native" commands;
c) target override is performed only for "simple" commands and not
for "native" commands.
Drop script_command() and extend command_unknown() to uniformly
handle all the cases above, fixing all the inconsistencies already
mentioned.
The handler's name command_unknown() is probably not anymore
appropriate, but will be renamed in a separate change.
Note: today all the commands in a) have mode CONFIG_ANY, apart for
"mem2array" and "array2mem" that have mode COMMAND_EXEC. But the
latter commands are registered during target init, so do not exist
during COMMAND_CONFIG and no issue is present.
Change-Id: I67bd6e47eb2c575107251b9192c676c27d4aabae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5665
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While registering a new command, jim accepts a pointer to command's
private data that will be accessible during the command execution.
Today openocd is not consistent and passes different private data
depending on the command, and then even overwrites it:
- "simple" commands (.handler) are registered with their own
struct command pointer as command private data;
- "native" commands (.jim_handler) at root level are registered
with NULL command private data;
- "native" commands (.jim_handler) not at root level are
registered with the struct command pointer of their root command
as command private data but, when executed, the command private
data is overwritten by the value in field jim_handler_data taken
from their struct command.
Uniform the usage of command private data by always set it to the
struct command pointer while registering the new commands.
Note: for multi-word commands only the root command is registered,
so command private data will be set to the struct command of the
root command. This will change later in this series when the full-
name of the command will be registered.
Don't overwrite the command private data, but let the commands that
needs jim_handler_data to get it directly through struct command.
For sake of uniformity, let function command_set_handler_data() to
set the field jim_handler_data also for "group" commands, even if
such value will not be used.
Now Jim_CmdPrivData() always returns a struct command pointer, so
wrap it in the inline function jim_to_command() to gain compile
time check on the returned type.
While there, uniform the code to use the macro Jim_CmdPrivData()
to access the command's private data pointer.
Change-Id: Idba16242ba1f6769341b4030a49cdf35a5278695
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5664
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
If current core is in EL0, it cannot use 'msr sctlr_el1, x0'
Change-Id: I04e60e39e4c84f9d9de7cc87a8e438f5d2737dc3
Signed-off-by: Cheng-Shiun Tsai <cheng.shiun.tsai@gmail.com>
Reviewed-on: http://openocd.zylin.com/6051
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {[^{]*} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I41a8447d487ec8f6f32c2babcbc73ac21c769344
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6152
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Enclose every Command within curly-brackets '{...}', even single
word commands.
Patch generated through:
sed -i 's/^\(@deffn {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx {Command} \)\([^{][^ ]*\)/\1{\2}/' doc/openocd.texi
Change-Id: I797e8d9f5ab0aa1936f350b340d3bdd52373f5aa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6151
Tested-by: jenkins
To avoid errors in the documentation, like the one fixed by change
http://openocd.zylin.com/6134/ , use a uniform notation across the
file so simple copy-paste will work.
Both 'Command' and '{Command}' are in use, with the following
statistics:
0 @deffnx {Command}
45 @deffn {Command}
31 @deffnx Command
382 @deffn Command
While 'Command' is the most popular, prefer the version within
curly-brackets that has to be used for multi-word definition like
'{NAND Driver}', '{Config Command}', '{FPGA Driver}', ...
Patch generated through:
sed -i 's/^\(@deffn \)\(Command\)/\1{\2}/' doc/openocd.texi
sed -i 's/^\(@deffnx \)\(Command\)/\1{\2}/' doc/openocd.texi
Change-Id: If692bbf7e546c5287f466a6aa6940d42b3d4655d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6150
Reviewed-by: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: jenkins
The commit 5280eb618a fixed all `adapter_khz` and
`adapter_nsrst_*` commands in the doc but missed grouping them. This
let the commands `adapter speed`, `adapter srst pulse_width`, and
`adapter srst delay` not indexed.
Tell texinfo about adapter sub-commands by grouping them in one.
Change-Id: Ida53c4f5cfe28827320c145c8d501d53e831623c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6134
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target mem_ap is a convenient way to access buses, memory and
peripherals behind an ARM AP.
The current implementation provides only access through OpenOCD
commands, because GDB remote protocol has to interact with a CPU
and has to operate on CPU states and registers.
Using GDB to access the memory is welcome, because GDB can resolve
the symbol's address from an ELF file and can nicely display the
content of complex struct and data types.
Extend mem_ap target with the bare minimal support for a remote
GDB connection, by emulating a fake basic ARM core. It means that
only a GDB that has support for ARM can be used (either 'aarch64',
'arm' or 'multiarch' GDB). This is not seen as a big limitation,
because the mem_ap target is mainly used on ARM based devices.
Add a minimalist register description for the fake CPU.
Fill the field 'debug_reason' as expected by GDB server.
Call the target halted event to reply to GDB halt requests.
For backward compatibility, don't open the GDB port by default. If
needed, it has to be specified at 'target create' or 'configure'
with the flag '-gdb-port'.
Change-Id: I5a1b7adb749746516f5d4ffc6193c47b70132364
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6034
Tested-by: jenkins
There are some breakpoint/watchpoint related code in armv8_dpm.c,
but seems not working for aarch64. Target aarch64 has its own
breakpoint implementation in aarch64.c. This commit follows the
same logic to add watchpoint support for target aarch64.
This commit also increases the size of stop_reason[] in function
gdb_signal_reply() since the old size is too small to fit in a
64-bit address, such as ffff8000115e6980.
Change-Id: I907dc0e648130e36b434220f570c37d0e8eb5ce1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/4761
Tested-by: jenkins
Reviewed-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Kevin Burke <kevinb@os.amperecomputing.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The comments currently used are not rendered.
Change-Id: I3fcfb6aee4dea9c4f9186a7aec70d382a1abd634
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6133
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add a file to the LICENSES directory to describe how file licenses
should be described in all the OpenOCD files, using the SPDX
identifier, as well as where all licenses should be in the source
tree for people to refer to (LICENSES/).
This file is mainly copied from the Linux kernel file in
Documentation/process/license-rules.rst
originally written by Thomas Gleixner <tglx@linutronix.de>, with
specific adaptations for OpenOCD.
Change-Id: I7a98fc756df90dc86dbc6e0c47c009a610a0318d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5973
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Add the full text of the BSD 1-clause license.
It was copied directly from:
https://spdx.org/licenses/BSD-1-Clause.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I71444e6a45d0e77fc57220cf1d579c010a27fdf3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5972
Tested-by: jenkins
Add the full text of the BSD 3-clause "New" or "Revised" License to
OpenOCD tree. It was copied directly from:
https://spdx.org/licenses/BSD-3-Clause.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I0e7977ed92af9d58a4a72152dd792045b237f2f0
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5971
Tested-by: jenkins
Add the full text of the BSD 2-clause "Simplified" license to OpenOCD
tree. It was copied directly from:
https://spdx.org/licenses/BSD-2-Clause.html#licenseText
Add the required tags for reference and tooling.
Change-Id: I1c2fb8ad7510ddd0d745308c0a9acc2764c31f4e
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5970
Tested-by: jenkins
The documentation of OpenOCD is released under the GNU Free
Documentation License, version 1.2, with embedded some part of
OpenOCD code released under the GNU GPL-2.0-or-later.
Update doc/fdl.texi with latest minor fixes as in
https://www.gnu.org/licenses/old-licenses/fdl-1.2.texi
Update doc/openocd.texi and move here the license chapter title
Add license file LICENSES/preferred/GFDL-1.2 from
https://www.gnu.org/licenses/old-licenses/fdl-1.2.txt
and add the required tags for reference and tooling, coping
mostly from the Linux kernel license file in the 'deprecated'
folder.
Add a readme file to link to the existing texinfo copy of the
license.
Change-Id: Ief96e0686257be7a70d4eeec442848bd6494763d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5969
Tested-by: jenkins
The stand-alone application "contrib/itmdump.c" is released as
GPL-3.0-or-later.
Add GPL-3.0 license in the licenses list.
Copy in subfolder stand-alone the GPL-3.0 from
https://www.gnu.org/licenses/gpl-3.0.txt
adding the header required by spdxcheck.py.
Change-Id: I238efc411e07ed6bc1eba23edbc91b3825c3d2c7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5968
Tested-by: jenkins
The script spdxcheck.py (used by checkpatch.pl) searches for the
license files in a dedicated folder, split in the subfolders:
"preferred", "dual", "deprecated", "exceptions".
Move the GPL-2.0 license from COPYING to the subfolder preferred,
adding the header required by spdxcheck.py.
The header is copied from equivalent file in the Linux kernel,
made by Thomas Gleixner <tglx@linutronix.de>.
Note: the license in COPYING matches exactly
https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
Add a minimalist COPYING in the top directory, as required by
automake, pointing to the files in LICENSES.
Change-Id: I1fd0abc57b554d74f0b00fabd6c8c822b2c4acb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5967
Tested-by: jenkins
Each one of CMSIS-DAP command handlers was responsible for setting
HID report number, which in case of USB bulk transport was not used
at all. The command had to be filled with 1 byte offset whereas
the response was read without an offset.
Introduce 'command' and 'response' pointers into struct cmsis_dap.
Use them for filling the command and read the response respectively.
CMSIS-DAP command parameter are now at positions as documented in
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__Commands__gr.html
Adjust buffer allocation for HID and USB bulk transports.
While on it, use h_u32_to_le() and h_u16_to_le() instead of per-byte
writes.
Change-Id: Ib0808d6826ba0e254c1007ace8b743405536332a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6120
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The hidapi cmsis-dap backend is using a packet_size of
64+1: 64 is the bMaxPacketSize0 and 1 is the hid Report-Id.
In hidapi::hid_write(), the packet_size is decremented by 1 and
stored for the next transfer.
The packet_size is now valid bMaxPacketSize0=64,
so when hid_read() is called, libusb_bulk_transfer() finishes w/o timeout.
For the libusb bulk backend, the same packet_size of 64+1 is used,
but there's no hid_write() to decrement and store it for the next read.
So the next time a read is done, it will try to read 64+1 bytes.
Fix this by putting the packet logic within each backend.
Use calloc() to allocate the struct cmsis_dap to be on safer side.
Change-Id: I0c450adbc7674d5fcd8208dd23062d5cdd209efd
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5920
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Now that the old drivers have been converted to libusb1, there is
no need to keep the build dependency from libusb0.
Drop libusb0 from configure and makefiles, remove the libusb0
helper and remove libusb0 and libusb-compat from the README files.
Change-Id: Icc05be74ae5971ba6cbb67d39107c709a4d826e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5993
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: Idef0b6cf10fab583bc8d13b3b4fadd5cc368c090
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5990
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: I3f334f2d02515d612097955e714910a587169990
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5992
Tested-by: jenkins
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
All ftdi devices require a dedicated line in the udev rules, but
some USB VID/PID present in interface and board config file is
missing in udev rules.
Add the missing ftdi devices in udev rules.
Change-Id: I850a4a95a2d4bb63b3fd09be803be8c23c4d6b49
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6101
Tested-by: jenkins
The API Jim_CreateCommand() in latest version of jimtcl leaks the
memory allocated internally by jimtcl when it converts the string
command-name to a Jim_Obj.
The fix is already merged upstream and would be available in next
jimtcl 0.81, expected in ~6 months, hopefully before the next tag
for OpenOCD v0.12.0.
OpenOCD v0.11.0 is distributed with jimtcl 0.79.
Debian distributes jimtcl as a separate library package and today
it's still on 0.79.
It make sense to keep using jimtcl 0.80 in current development
cycle to test it further. But having this background memory leak
noise hides the eventual new memory leaks that could come from the
development activity.
This patch uses the internal jimtcl API Jim_CreateCommandObj() and
correctly free the internal object, avoiding the memory leak.
Being an internal API, it is not accessible if OpenOCD is linked
with an external jimtcl library. Nevertheless, building jimtcl as
a submodule of OpenOCD makes the trick effective.
The scope of this patch is thus limited at developers that build
OpenOCD with jimtcl submodule and need to control and debug memory
leaks.
This patch is supposed to be removed as soon as jimtcl 0.81 gets
available.
The added code is located, on purpose, in an area of the file that
hopefully will not conflict other patches pending in gerrit.
Change-Id: I4d300ad21bdb6c616c3f0f14b429b4fdf360900d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
After bootstrapping build, if we want to do an out-of-tree build (ie: in the
OOT-build dir) we have a build failure because build system relies on
the OOT-build/src directory exists
```sh
./bootstrap
mkdir OOT-build
cd OOT-build
../configure --disable-dependency-tracking --<flag1> --<flag2> ...
make
$ LANG=C make
cat ../src/helper/startup.tcl ../src/jtag/startup.tcl ../src/target/startup.tcl ../src/server/startup.tcl ../src/flash/startup.tcl | ../src/helper/bin2char.sh > src/startup_tcl.inc || { rm -f src/startup_tcl.inc; false; }
/bin/bash: line 1: src/startup_tcl.inc: No such file or directory
make: *** [Makefile:6603: src/startup_tcl.inc] Error 1
```
These kind of errors are fixed indicating relevant directory creation in
Makefile.am before actually relying on it.
Change-Id: I8185fd41ef942184597dc4c0092796034572cbe1
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6106
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduction of 'enum stm32l4_rdp' enumerating possible RDP levels for
devices with and without TrustZone.
also in 'stm32l4_flash_bank' structure we added and rdp and tzen members
to store read values by the helper 'stm32l4_sync_rdp_tzen'
these new members are used to display security and protection status
while probing the flash.
Change-Id: Icf883189715278a3323fe210d295047678b16592
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5541
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Antonio Borneo
Yun Liu
Leonard Crestez
Marc Schink
Tomas Vanek
Cheng-Shiun Tsai
Yasushi SHOJI
Liming Sun
Thomas Gleixner
Adrian Negreanu
Raúl Sánchez Siles
Tarek BOCHKATI