crc check was always performed on newly flashed data, now it is optional
flash mem can be locked by writing a specific word to a specific address in flash.
to verify flash, target must be halted, and this will (when the new halt sequence is implemented) require reseting the chip. if the target is reset after writing the lock words, then it will lock, hence the CRC will fail because it is not possible to read stuff from the target.
also added a function that resets the jtag state machine.
this is not used yet, but will be soon.
it is implemented to allow strict control over JTAG state machine, necessary to implement to halt and unlocking sequences.
i had started my code from dsp5683xx, i renamed a bunch of stuff to names i consider to be better.
i believe no one is using this code, so nobody should be affected. (it's not too late to do this change)
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
Pprogram that loads another program into memory is actually writing the
D- side cache.
The instructions it has loaded can't be executed until they reach the
I-cache.
After the instructions have been written, the loader should arrange to
write back any containing D-cache line and invalidate any locations
already in the I-cache.
For the MIPS Architecture Release2 cores, we can use synci command
that does this job.
For Release1 we must use "cache" instruction.
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
For all architectures we use distinct common magic number,
and this should be a uint32_t type.
Otherwise, comparison with macros will yield compilation
warning.
before doing anything with the flash module (FM) the clock divider must be set.
if erase_check was the first thing done with the FM after reset then an error would be generated because the clk divider was not set.
now erase_check sets the clk divider.
reorganized code to get rid of compiler warnings
the warning were related to allignment, i do not get these warning on my build system (i've tried setting the compiler flag but it doesn't work, still working on why) so i cannot detect them (yet.)
This corrects two issues found with openocd.
d7f71e7fe9 removed some code that was
being used.
The above then caused even more code to get removed by commit 1cfb2287a6.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
So far image_load command tries to load ELF binaries to address
discovered by reading p_paddr member of a Program header of an ELF
segment.
However, ELF specifications says for p_paddr : ...Because System V
ignores physical addressing for application programs, this member has
unspecified contents for executable files and shared objects.
ARM ELF specifiaction goes even further, demanding that this member
be set to zero, using the p_vaddr as a segment load address.
To avoid the cases to wrong addr where p_paddr is zero,
we are now using p_vaddr to as a load destination in case that *all*
p_paddr == 0. Basically, this patch re-implements the approach present in
BDF's elf.c, which is used by GDB also (so that we can be consistent).
cygwin does not define sleep, so use our internal win32 version.
caused by commit 9d4aec6bda
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
- works on Cortex-M3 with ThreadX and FreeRTOS
Compared to original patch a few nits were fixed:
- remove stricmp usage
- unsigned compare fix
- printf formatting fixes
- fixed a bug with overrunning a memory buffer allocated with malloc.
Freescale iMX53 doesn't seem to like unaligned accesses to his memory
mapped registers.
Anyway this patch makes dump_image/load_image 4X faster for every
access through APB.
Signed-off-by: Luca Ellero <lroluk@gmail.com>
accidentally invoked return jtag_execute_queue() in the
middle of a fn. Hmm.... I would have expected gcc or
at least lint to catch this.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the patchup code would get false positives when checking
whether a dbgbase had to be corrected.
The solution is to have autodetect default, with manual override
in scripts.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Could this cause confusion as data sent to write would be flipped
and then if the caller subsequently used the data, e.g. a
compare mismatch might happen?
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Really a Cortex-A specific option, but there is no
system in place to support target specific options
currently and there has been no need for such a system
until now.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The patch below fixes step <address> on mips_m4k.
Spencer Oliver <spen@spen-soft.co.uk>:
The current code is used on all other arch's - is
there a underlying issue with those aswell ?
I don't think dsp563xx_once_read_register() would ever
be called with len==0, but it would have been broken in
that case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Problem is, trying to print "Hello, world!\n" just prints endless H's, because r1 is never incremented.
One way to fix it would be to add a "++" after "r1".
Fix a bunch of typos.
Most are in code comments, so nothing should break. UNKOWN_COMMAND and
CMD_UNKOWN are not used elsewhere, so correcting the spelling should
also not break anything.
This patch add rudimentary gdb support. The gdb register list
order is corrected. All registers are now 32bit width. Events are
send to signalize gdb the current target status. Resume and step
function was corrected to consider a modified pc register. Read/write
memory now support L memory type, this means a memory with alternating
y/x memory words. The memspace variable, used by gdb, is now observed
before a default memory access is initiated. Dummy functions for breakpoint
and watchpoint are added.
This patch tries to make some order in "apsel" mess.
"dap apsel" command was quite useless (and broken) by itself.
With this patch we can use it to select between AHB or APB memory access
(previous patch 05ab8bdb81 was somehow broken).
- moves member apsel (in struct adiv5_dap) to ap_current
- adds apsel member
this strange choice is made trying to keep coherence in "dap apsel" command
and to keep compatibility with other code (for example cortex_a8).
Signed-off-by: Luca Ellero <lroluk@gmail.com>
This patch move the dsp563xx_target_create function to the
related code block. Also the target examine function was added
and the register cache is initialized in a separate function. The
missing functionality to invalidate the x memory context on memory
writes was also added.
This patch change the return value on a jtag communication error
to TARGET_UNKNOWN because this function should return the current
target status and not a error code from the underlying api call.
Also the validity of the jtag_status is extended to all static
bits in this value.
Rodrigo L. Rosa
Heythem Bouhaja
Jie Zhang
Stefan Mahr
Drasko DRASKOVIC
Øyvind Harboe
Jie Zhang
Peter Horn
Spencer Oliver
Freddie Chopin
Michel Jaouen
Broadcom Corporation (Evan Hunter)
Luca Ellero
Andrew Lyon
Mathias K
John and Tina Peterson
Uwe Hermann