SWIM is implemented by (ab)using the HLA API. This was acceptable
when OpenOCD code did not provided a clear separation between
transports and related APIs. Still today SWIM in OpenOCD is only
supported by STLink, so the decision to re-use the HLA API was the
simpler way to implement it.
After commit efd1d64222 ("adapter: switch from struct
jtag_interface to adapter_driver") the transports API are better
split and SWIM can be implemented as a separate set of API. This
would open the possibility to extend OpenOCD for other adapters
that provide SWIM, e.g. versaloon, or through SPI emulation [1].
Introduce a new set of files swim.[ch] to handle the SWIM API.
Beside the API that almost match the transport low-level data
communication (system_reset, read_mem, write_mem), add a further
API reconnect. Today, inside HLA STLink code, the reconnect is
implemented by hacking the HLA API state(). Please notice that
due to this hack the return type is incorrect; stlink_usb_state()
returns ERROR_OK in SWIM mode, while its return type is enum
target_state. Ignore the type mismatch and still call the HLA API
state in the new SWIM API reconnect. Further commit will fix it.
[1] http://kuku.eu.org/?projects/stm8spi/stm8spi
Change-Id: I52018e1e2200cbd41af8e5031f7b35dc761b61d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5528
Tested-by: jenkins
The transition of STM8/SWIM out of HLA will require a new struct
swim_ops in struct adapter_driver.
To simplify the development, make the HLA interface temporarily
accessible through the struct adapter_driver.
This commit will be reverted after the swim rework.
Change-Id: I1e4f370cf64641164d7bcaa22f75ac58c9240052
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5527
Tested-by: jenkins
In the driver's code it's widely used the enum hl_transports for
any check concerning the current transport, even for the non-hla
transport dapdirect.
The driver already provides a stlink specific enum stlink_mode
that can be used in place of the hla one.
Replace the hla enum with the stlink one allover the code.
Introduce a hla specific wrapper stlink_usb_hl_open() to cope with
the only API that requires the hla specific enum.
The overall behaviour is not changed, with exception for a debug
message in stlink_usb_open() than now prints the numeric value of
stlink enum in place of the numeric value of the corresponding hla
one.
This change prepares the road for moving SWIM transport out of hla
by removing any reference to the macro HL_TRANSPORT_SWIM from the
stlink driver.
Change-Id: Ieeea34f312245a94bfc1333087afdb8eb9f77139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5526
Tested-by: jenkins
This is a follow-up to 3c9bd7c6f3.
Change-Id: If430f7fcfbba084d9cd74b32344ad43508a96a77
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit da41bce3ae ("target/arc: introduce breakpoint
functionality") introduces a mismatch between the format string
and one int constant.
Change the format string to match the int constant.
Change-Id: I0d59552205551b90e165c0a2e3fef247ad0c7701
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: da41bce3ae ("target/arc: introduce breakpoint functionality")
Reviewed-on: http://openocd.zylin.com/5655
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Expression like (0xffff << 16) evaluate to type int, which is not able
to hold that value, producing a warning when compiling with
-fsanitize=undefined. This patch makes most of the cortex_m constants
unsigned using the BIT() macro or appending "ul" when possible to fix
the undefined behavior warning.
Signed-off-by: iosabi <iosabi@protonmail.com>
Change-Id: I7af194305ef612d7a32e74eaf9f11dd85fa87f32
Reviewed-on: http://openocd.zylin.com/5583
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types OPEN_BRACE -f {} \;
Change-Id: I6d1356ed11e2699525f384efb7556bc2efdc299f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5628
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The coding style is quite permissive allowing 120 chars per line,
but abuses are still present.
Fix them, wrapping the lines.
Change-Id: I94d66b651d759a60ec35f7ba115c43933e70ed69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5626
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The re is no need to split a long string, apart for fitting the
predefined line width.
Join the consecutive string fragments.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types STRING_FRAGMENTS -f {} \;
Change-Id: I8de52d572b0e3d4788c1d4d2b0cf8f94c7f08409
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5625
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The statement "else" should not be on a new line when follows a
close brace '}'. Fix it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ELSE_AFTER_BRACE -f {} \;
Change-Id: I8af247ec3f75a69713d7cb1e73881254d16c189e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5623
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
For void functions, a return as last statement is useless.
Remove it.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types RETURN_VOID -f {} \;
Change-Id: Ie0616fe98623f30d2d7b04ac9517d669774092de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5622
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Functions that have no parameters should use "void" as parameter
in the function declaration.
Issue identified and fixed by script checkpatch from Linux kernel
v5.1 using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_WITHOUT_ARGS --fix-inplace -f {} \;
Change-Id: If104ac75b44e939ec86155ff7b5720f2e33c6b39
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5621
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TRAILING_WHITESPACE --fix-inplace -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Ie7e3a236f4db9c70019e3b3c7e851edbd3a9dd84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5616
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I7b523f0ab5ec047ff167742a44c29984ac672cf4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5615
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Identified by checkpatch script from Linux kernel v5.7-rc1 using
the command
find doc/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TYPO_SPELLING --strict -f {} \;
Change-Id: I1269ac966027439e16eb6e63179e43925bec37fa
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5614
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Commit 87a4158acf ("drivers: xds110: Clean up command syntax and
documentation") does not follow the documentation structure that
lists the adapters in cpt 2 "Debug Adapter Hardware" then lists
the adapter commands in cpt 8.2 "Interface Drivers"; it puts all
in cpt 2.
While doing that, uses an incorrect texinfo syntax that causes the
following warnings at compile time:
doc/openocd.texi:543: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:547: warning: @deffn should only appear at the beginning of a line
doc/openocd.texi:552: warning: @deffn should only appear at the beginning of a line
Move the documentation of xds110 commands in the proper chapter
and fix the texinfo syntax.
Change-Id: I0b3f0fe0c687f194bb02e2d81aca86fcd4fdd718
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 87a4158acf ("drivers: xds110: Clean up command syntax and documentation")
Reviewed-on: http://openocd.zylin.com/5613
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Edward Fewell <efewell@ti.com>
Starting from version 8, gcc issues a warning if strncpy could be
able to truncate a string (so without adding the zero-termination
char in destination) by copying exactly "size" char from a source
string not shorter than "size".
Such truncation from strncpy could actually be the desired code
behaviour, but the way to silent gcc only locally (without global
disabling with -Wno-stringop-truncation) through pragma has other
side effects on portability.
In current code, the source string is always "eth0", because has
been checked right above. So this is a false positive from gcc,
being always strlen("eth0") < 16, the sizeof(ifreq.ifr_name).
Silent gcc by decrementing the "size" and remove:
error: ‘strncpy’ specified bound 16 equals destination
size [-Werror=stringop-truncation]
This file is only optionally compiled together with ZY1000 driver
with --enable-zy1000 --enable-ioutil. This combination is not
checked in jenkins, so the error passed unnoticed.
Plus, the configure flags above are both deprecated!
Change-Id: I229e66227cfd3513139feeaffa47a6e1ec00767b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5631
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The commands "ocd_find" and "capture" are registered directly
through the jim API, instead of the common way to describe them
in a struct command_registration that is then passed to the helper
register_commands().
This cause the two commands above to not have either "help" nor
"usage" string nor a properly identified "mode".
Since the following line registers the commands listed in struct
command_builtin_handlers, simply add the two commands above in the
same struct.
Change-Id: Id6ee11dac3b18364deeed65ee8e18ad80152750a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5644
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The state machine of cortex-m have to pass through a set of state
before it get in "halted".
Add one more "arp_poll" to achieve the proper state during a
"reset halt" command in engineering boot.
Change-Id: I90828bf20ef75bd4018f8b911f727ae69c4d6e8f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5649
Tested-by: jenkins
Reviewed-by: Richard Braun <rbraun@sceen.net>
Restore the prompt after the "history" command is invoked.
Change-Id: I3d0744abbc58e82b039e06f21675efa180e8e1b0
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3414
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With this patch we introduce set/unset breakpoints
routines and add/remove bp handlers.
Currently soft breakpoints are only supported.
Changes since v1:
* Change if-statement in arc_remove_breakpoint
* Squash changes from http://openocd.zylin.com/#/c/5641/
in this commit to fix build.
Change-Id: Ib10ccdb02fd1606e4f407f012b1bee106a8ffccd
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5641
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This commit introduces helper instruction read/write functions
for further bp functionality.
Change-Id: I619fbe2870ef6365c29ed1618bb83b6f7eb84690
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5640
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
get_thread_reg() allows gdb to request the register value of a specific
"thread."
set_reg() allows register writes without getting a giant list of
registers first.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I87faa1c8793916b9ee476dd696f0695a07ca2b41
Reviewed-on: http://openocd.zylin.com/5324
Tested-by: jenkins
this change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
a table with register offset will be introduced, thus correct register
addresses will be obtained using this table and the driver internal
function 'stm32l4_get_flash_reg' will be responsible of this.
Change-Id: I74bf61a83fe53575623640af0328b3253ecc796f
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5508
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Michael Jung <mijung@gmx.net>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
According to RM0432 rev. 6, only 0x1001 "Z" rev. applies for STM32L4P5/Q5.
Verified on real device. Whether other revisions exist is unclear.
Change-Id: I761ae077d089b06925fc0fe1ff2b1e478b8a66fa
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5521
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Introduce a variable 'size' and reduce the number of dereferencing
*reg_list_size by using the variable.
Change-Id: I3bdf1485a4ed8e34435e8acb3efd0df8d802508c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5326
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Commit c2cecc74b0 ("Move JTAG interface list to new files.")
merged in mid 2009 introduces an unused and empty function that
the developer expects to use for loading adapter drivers from
shared libraries. This have never happened and the function is
still empty and unused.
Remove it.
Change-Id: I7c88dbf8a9747e96e5ca4e6e7038ac0f232604fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5601
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
All the servers open the listening socket during openocd "init";
it's not possible to change the tcp port or the bind address
after "init".
In current code, the call order during "init" permits to change
the port and bind address of tcl and telnet server if the related
command is issued after "init" in the same script or on openocd
command line. This is not guaranteed to work if the call order
during "init" changes, so it's incorrect.
Change the commands "bindto" and "*_port" to COMMAND_CONFIG.
Change-Id: Id88f225a67a872b4bcaf3b799466bddedc248015
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Christopher Head <chead@zaber.com>
Fixes: https://sourceforge.net/p/openocd/tickets/264/
Reviewed-on: http://openocd.zylin.com/5595
Reviewed-by: Christopher Head <chead@zaber.com>
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: I4efbd9af5be7e16213dcc7cb95de936ecde2fcef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5173
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Ibac9b36682d58f81e34ca2b51e6260e7d472fb0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5172
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: I503cb0a96c7ccb132f4486c206a48831121d7abd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5171
Tested-by: jenkins
GCC 10 defaults to -fno-common which breaks the sharing of bitbang_swd
struct between bitbang drivers due to a missing extern.
Change-Id: I2b4122f7939cec91a72284006748f99a23548324
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5592
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Fix build error on Mac OS X Catalina (10.15.4) caused by formatting
stm32l4_info->wrpxxr_mask, which is uint32_t, as uint16_t in the debug
log message. Adding casting to uint16_t before substitution because only
lower 16 bits are significant for debug purposes.
Change-Id: Iddb87cd156dfc84ab1f91cd15a1ddee6b646d412
Signed-off-by: Ilya Kharin <akscram@gmail.com>
Reviewed-on: http://openocd.zylin.com/5590
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Antonio Borneo
Marc Schink
Tarek BOCHKATI
Edward Fewell
Tomas Vanek
Marc Schink
Alistair Francis
Paul Fertser
iosabi
Evgeniy Didin
Tim Newsome
Andreas Bolsch
Andreas Fritiofson
Ilya Kharin