Only Tcl comments are now supported. For classic style
commands comments were supported at the end of the line.
Move in the direction of letting the script language
decide syntax, rather than have special rules for some
commands.
Before this patch goes in, the scripts should be updated
to use ;# instead of # for end of line comments.
> mdw 0 1 2
mdw ['phys'] address [count]
zy1000.cpu mdw address [count]
Command handler execution failed
in procedure 'mdw'
> mdw 0 1 #2
mdw ['phys'] address [count]
zy1000.cpu mdw address [count]
Command handler execution failed
in procedure 'mdw'
> mdw 0 1 ;#2
0x00000000: ffffffff
> mdw 0 1
0x00000000: ffffffff
> mdw 0
0x00000000: ffffffff
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
End of line comments fixed with ';' before '#'.
Added few additional 'space' to keep indentation in
multi-line comments.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
the unprotect fn in stm32 needs to unprotect more sectors
than was requested aligned to some boundary.
Print warning when this happens.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
some chips unprotect more than the range asked for. The
protect fn, must unprotect/protect minimally the range given.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Some flash's do not support buffer writes, so we now check
they are supported before trying to use them.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The existing code used incorrect timeout values for the various cfi
operations. We now calculate the timeouts and convert to
msecs if necessary.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
LPC2xxx do not require reset_config srst_pulls_trst. This can cause various "strange" problems when flashing the chip, because "reset halt" actually allows the chip to run for some short period of time and execute some code.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
commit 740b9e25b4 broke the drivers
for ftdi and parport due to retval already being defined.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
If the JTAG speed has not been set, then it has no defined
value, add code to propagate the error.
No change to actual behavior as no new failure paths have
been introduced. This is a no-op patch to make subsequent patches
smaller.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
* added support for targeting particular tap
* improved file reading
* improved command line parsing
* added progress meter
* more readable time measurement output
Hi everyone,
Since a call went out for patches... been sitting on this for months. For some
reason, the xscale trace buffer is automatically disabled as soon as a break
occurs and the trace data is collected. This patch was a result of the
frustration of always re-enabling it, or else hitting a breakpoint and checking
the trace data, only to discover that I forgot to re-enable it before resuming.
Don't see why it should work this way. There is no run-time penalty, AFAIK.
Along the way, I also cleaned up a little by removing the ugly practice of
recording wrap mode by setting the fill count variable to "-1", replacing it
with an enum that records the trace mode.
I've been using this for months. Comments, criticisms gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Due to commit e40aee2954d2beabe1d8c530d9ff1e564fb01f48 we now honour the
targets 'reset_config' setting. Previously we ignored the srst setting
for luminary targets.
Luminary targets have never supported using srst to reset into debug mode
so remove the option from the target configs files.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Currently the cmd 'cortex_m3 reset_config' will overide the default
target's 'reset_config'.
Chnage the behaviour to use the target 'reset_config' if configured and
fallback if not.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
When this config was updated in commit e3773e3e3d
the old jtag declaration was not removed.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Rename Atmel target scripts which had wrong name ("at91" missing for ARM7 AT91SAM7..., "at" missing for AVR ATmega...)
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
it's a lie that is somewhere in the vicinity of the
truth. Certainly 64MHz confuses gprof and produces
zero output and no error messages.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Update subproject jimtcl to fix issue with make install.
see jimtcl commit 373b721510fd2d0754a41cc70a3b7cfd02e929bd
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
As we default to building jimtcl the help text should show that.
No change in functionality or configure args required.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
STMicroelectronics controller SMI is not SPEAr specific.
Rename it and change name to every symbol in the code.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Modified spearsmi driver to include support for STR75x
Added missing initialization in tcl file for STR750
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
If flash chip is not listed in the table, or if no flash is
connected, pointer must be properly initialized.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Tormod Volden
Michael Schwingen
Michael Trensch
Øyvind Harboe
Antonio Borneo
John Devereux
Paul Richards
Spencer Oliver
Freddie Chopin
Andrew Leech
Rolf Meeser
Mike Dunn
Piotr Esden-Tempski