Instances of struct flash_driver are never written to at runtime. For a
small amount of memory saving and also robustness (fewer things for
stray pointer writes to hit), mark them const.
Change-Id: Iadbbbc2fac0976d892699200000c5f02856729f3
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4803
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The code for this command is currently replicated in cortex_a and
in mips_m4k and is going to be added again for cortex_m.
Plus, it is going to be obsoleted by the HW thread pseudo RTOS.
Consolidate in smp.c a single instance of the command. This will
simplify both obsoleting it and adding it to cortex_m, whatever
change comes first.
Change-Id: I03cd857e21fa3f7202fdcee36bcbd5aae30a609d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4991
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Seams over-engineered having two separate commands to turn SMP
on/off. Plus it is missing the possibility to dump the current
status of SMP and would be weird adding an additional command
for it. Moreover, such commands are replicated in few targets so
it would make sense centralizing them.
- Deprecate the commands "smp_on" and "smp_off".
- Add a new command "smp" that accepts optional parameters
"[on|off]" and prints the SMP status when run without
parameters. This replaces the two commands above.
- Put the deprecated and the new command handlers in smp.c
- Update the documentation, except for mips_m4k, since it is not
available yet.
- Promote the macro foreach_smp_target to global context and use
it where possible.
Change-Id: Ia72841c1a3bd6edd4db4cc809046322f498617e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4615
Tested-by: jenkins
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The imx8m also has a Cortex m4 so add a target for it.
Change-Id: I2abf62b6232c547fe9b12507f459835b11c63a6d
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-on: http://openocd.zylin.com/4501
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Use target_addr_t exclusively for comparison of sector boudaries and
address range.
Use the last addres for both address range end and sector end.
It avoids problems with a flash bank mapped at the very end of
target address space.
Change-Id: Idf97c837453d97cbc4cf8a1c76ad799f4142f19e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4985
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This represents months of continuing RISC-V work, with too many changes
to list individually. Some improvements:
* Fixed memory leaks.
* Better handling of dbus timeouts.
* Add `riscv expose_custom` command.
* Somewhat deal with cache coherency.
* Deal with more timeouts during block memory accesses.
* Basic debug compliance test.
* Tell gdb which watchpoint hit.
* SMP support for use with -rtos hwthread
* Add `riscv set_ir`
Change-Id: Ica507ee2a57eaf51b578ab1d9b7de71512fdf47f
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4922
Tested-by: jenkins
Reviewed-by: Philipp Guehring <pg@futureware.at>
Reviewed-by: Liviu Ionescu <ilg@livius.net>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Some boards require a slower clock speed because of passive components on the
JTAG/SWD lines. The previous implementation would first try to discover the
chips on the default speed, and only after discovery switch to the requested
adapter_khz speed.
This patch moves the speed change to just before entering the SWD/JTAG mode,
which should alleviate this problem.
Tested on an STLink V2 clone.
Change-Id: I9734452dcc8bb28d6629e64d9a7e32ef92868cf9
Signed-off-by: Frans-Willem Hardijzer <fw@hardijzer.nl>
Reviewed-on: http://openocd.zylin.com/4818
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Fix indent of the macros in header file, no functional change.
Change-Id: I4d1dba5725155200148d1543c45bad919f6cd37e
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4995
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
These macros are missing parenthesis around the argument, which can
lead to side effects, add them. Replace the argument name to avoid
conflict with uint32_t data type, since the macro can be applied to
other data types as well.
Change-Id: I32d2ffec6c062795d7c8bb23d1dfa3378bfc3a58
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/4994
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Bit 4 in OPTSR is IWDG1_SW (the code originally called it IWDG1_HW, but
the reference manual refers to it as IWDG1_SW). This is broken out into
a separate variable, independent_watchdog_selection, in stm32x_options.
However, this is not necessary: bit 4 is included in the user_options
field, which includes all of bits 2 through 7, and
independent_watchdog_selection is not referenced anywhere else. Delete
the field and just rely on user_options to transport that bit, along
with all the other bits it contains, between stm32x_read_options and
stm32x_write_options.
Change-Id: I4da63df9272cf091267b956c412b95671ea1d3c9
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/4744
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Write to register DP_SELECT can fail, but both functions
swd_queue_dp_bankselect() and swd_queue_ap_bankselect() return
void and do not propagate the error.
Change the return type of the two functions to int and check the
returned value.
Invalidate the cached value of DP_SELECT if the write fails.
Change-Id: Iba6ef8b0c2332e7f7efb66337d558fb7a4a0d39c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4980
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the register DP_SELECT is written directly, e.g. with command
<dap> dpreg 8 <value>
the cached value in OpenOCD is not completely updated with the new
value, thus creating issues in the following AP and DP read/write
that rely on the cached value.
Update the cached value while writing to DP_SELECT.
Change-Id: I8221b10cd6fc1fbe73e6b834b68820b43480e1a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4979
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While on it add two missing new lines.
Change-Id: I0d54740479bc462b734f91686f0931824796b598
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4888
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
This should allow users to configure flash at >32-bit addresses.
Change-Id: I7c9d3c5762579011a2d9708e5317e5765349845c
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4919
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Targets can use this to expose how many address bits there are.
gdb_server uses this to send gdb the appropriate upper limit in the
memory-map. (Before this change the upper limit would only be correct
for 32-bit targets.)
Change-Id: Idb0933255ed53951fcfb05e040674bcdf19441e1
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4947
Tested-by: jenkins
Reviewed-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds "hwthread", a pseudo rtos that represents cpu cores
in an SMP system as threads to gdb. This allows to debug SMP
system kernels in a more sensible manner and removes the current
atrocities of switching gdb manually between CPU cores to update
the context.
Change-Id: Ib781c6c34097689d21d9e02011e4d74a4a742379
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3999
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Graham Sanderson <graham.sanderson@gmail.com>
API v2 deprecates using command STLINK_DEBUG_READCOREID to read
the core ID.
Switch to STLINK_DEBUG_APIV2_READ_IDCODES on new stlink firmware
version.
Change-Id: Iabadfc116c57f2c31f08f2e77baefea0cf90bdc3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4826
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Most of ST-Link commands return an error code, but this is almost
never checked.
Check for the error code for every command that returns it.
Change-Id: Ifc4e32f8c73196de23700ba0989bfdfe0f5b46e3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4825
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
API v2 implementation for command READALLREGS returns the status
in the first two bytes, followed by two bytes of padding.
This makes the reply 4 bytes longer and changes the offset of the
first register value to 4.
Fix it for the case API v2 and clean-up the management of the
return value.
Change-Id: I448c82bcc0baa72d66fdfe7f0c525b94f8a4468b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4824
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
When the connection with target is lost on the physical JTAG/SWD
link (either wire disconnected or DAP/TAP in reset), STLINK fail
to connect and returns error STLINK_JTAG_GET_IDCODE_ERROR.
Add it in the list of known errors.
Change-Id: Iabd6e6892111726f614345497d9286554bfe4ac0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4982
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The new firmwares for ST-Link support handling multiple AP, but
are (actually) limited to the AP number in range [0..8].
Any tentative to operate on AP number higher than 8 returns an
error "bad AP".
Add the error code and the related message.
Change-Id: I78a98b2612d10e580d03fc43ed9f2b09619d39d8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4981
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The function command_unknown() is expected to return a value
recognized as JIM error code, as it is correctly done in the
other cases it returns.
Fix the only case in which command_unknown() does not return
a JIM error code, by s/ERROR_FAIL/JIM_ERR/
Change-Id: Ib98b75755ae36870bd68c17f8839ddbfa06c6312
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4973
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix a warning identified by clang 7.0.1:
stlink_usb.c:1092:3: warning: Value stored to 'p' is never read
p += sprintf(p, "S%d", swim);
^ ~~~~~~~~~~~~~~~~~~~~~~~
Change-Id: Ic9da57e19ceecb0e3d65d3ea3412a05e1c2c779a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4945
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The null pointer used as second parameter to gdb_put_packet() is
passed as second parameter to the memcpy() in line 408 of
gdb_put_packet_inner(). In this case memcpy() does not segfault
because also the parameter length is zero. Nevertheless, the
prototype of memcpy() requires a nonnull pointer.
Fixed by passing an empty string in place of the null pointer.
Issue highlighted by clang 7.0.0 with warning message:
"Null pointer passed as an argument to a 'nonnull' parameter"
Change-Id: Ib3dde95d76fcc5fb245ee2d6669e5535d0e0b127
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4946
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- TDI/DO is not pin 2 and in fact, we don't even need to mention which
pin number it is. "TDI/DO pin" is descriptive enough.
- FT2232D link didn't work anymore. It could have been updated to the
current working FT2232D link but changed to link the FT2232H instead
which is the latest generation and the most commonly used these days.
- Taking advantage of the change, link to the MPSSE document updated.
It still worked but through a redirection, so updated just in case the
redirection stops working.
Change-Id: Ia7d01bbcac2158026831edb010a6b50f58351e42
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4908
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Christopher Head
Antonio Borneo
Angus Ainslie
Tomas Vanek
Tim Newsome
Frans-Willem Hardijzer
Marek Vasut
Marc Schink
Matthias Welwarsky
Diego Herranz