Active watchdog forces reset during armv7m_checksum_memory()
in verify_image command if run just after reset init.
COP watchdog in KL series and WDOG32 in KE1 series
have longer timeout however they need to be disabled too.
The change extends 'kinetis disable_wdog' command to optionally
probe the chip and use appropriate algorithm to disable watchdog.
Setting of cache type is also split from flash_support flags.
Tcl command 'kinetis disable_wdog' is called in reset-init event.
Change-Id: I3191e230f38b679ed74f2a97fe323ef8fb3fe22e
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3901
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3925
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Config file renamed to ke0x.cfg and a notice added to texi.
While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG.
Removed per device configs as they set CHIPNAME and nothing more.
Let's use reasonably universal chip name 'ke' set in family config.
Change-Id: I313db87a59f25f968eb3c27df155780b67becee8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3897
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3896
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
configuration covers all 8 Cortex-A53 cores and auxiliary Cortex-M3
used for power management.
Change-Id: I5509f275aa669abe285f9152935ecdcbcd0c402e
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4009
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested with a Dresden Elektronik deRFmega128 module.
Change-Id: I91da3b11b60e78755360b08453ed368d6d396651
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/2790
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit 25d7ba19c9 introduced a problem
with 'reset halt' due to setting srst_pulls_trst:
Error: cortex_m.c:595 cortex_m_halt(): can't request a halt while
in reset if nSRST pulls nTRST
Sorry, I don't know why I overlooked it when I tested #3722.
Change-Id: I41e9473dd91a86d93cf3e78b1fbbdfe1dd188d83
Reported-by: Ladislav Laska <laska@kam.mff.cuni.cz>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3942
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This seems to be a leftover from borrowing from omap3* configs. Since
SJC is not enabling or disabling the DAP tap, and the tap is always
available, the extra tapenable command causes warnings on startup
(can't enable what's already enabled).
Change-Id: I7514436d565aa5b91876dbdab547956f36dcab77
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3892
Tested-by: jenkins
Chip ID and flash layout taken from
Atmel-11102F-ATARM-SAM4C32-SAM4C16-SAM4C8-SAM4C4-Datasheet_27-Mar-15
and tested on a SAM4C32-EK (rev A).
Change-Id: I68aae5b60994c0b5964ea9031d40bc76ba025675
Signed-off-by: Owen Kirby <oskirby@gmail.com>
Reviewed-on: http://openocd.zylin.com/3527
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target tcl to enable debugging of ARM Cortex-A5 on ADSP-SC58x
Change-Id: I378f8b94b7d6d6b9d0567985abc0e36aea7c8dea
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/3125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Remove comment about workaround of not working 'reset halt' - not needed
as 'reset halt' is working as expected @ EDBG with srst_only.
Add srst_pulls_trst to reset_config as it no more triggers an error.
Change-Id: I47cf445690c46ccfb866900cddbfcaefc8649f82
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3722
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
At least on my (phyCORE-AM335X) system, the AM335x watchdog
needs to be disabled to use OpenOCD for more than 6.5 seconds
after reset.
Change-Id: I3d883a9f572b0ccb92f9864853a00c372e39d7f2
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Reviewed-on: http://openocd.zylin.com/3391
Tested-by: jenkins
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Instead of updating these regularly we can just accept any IDCODE for the
boundary scan TAP.
The only downside might be that it's not immediately obvious if you
source a config for the wrong type of STM32.
Change-Id: I96d4d81699a491b3a46de3f0d3fd078ffddad4e4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3385
Tested-by: jenkins
Kinetis driver checks MDM STAT register to detect secured state of MCU.
Original version often reported a blank device as secured one.
Change #3010 has not fixed all false reports.
After changes in arm_adi_v5 infrastructure secured devices was not detected
at all.
New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and
MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop
are detected reliably.
Detection is run in both kx.cfg and klx.cfg from examine-start event,
not examine-end as before. Event is configured only for non hla adapter.
Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init.
Such frequency is not supported in VLPR CPU mode and with JTAG.
Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3547
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Increase workareasize when it is know we have a larger device.
Change-Id: Ieaee92e7cd25cc201989f14de122349698871412
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3378
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
PSoC4 design prevents reset halt/init with standard/low level
SWD adapter if hw reset line configured. Give user hint
to use 'reset_config none' in such case.
Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3617
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested with TI MSP-EXP432P401R LaunchPad, via both on-board XDS110-ET (swd)
and external J-Link (jtag).
Change-Id: Ic0caa8516a155754b1c88a04acc8d3c511d9a5f7
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3485
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn
or CortexXn. Further it's Cortex-M0+, not M0plus.
Cf. http://www.arm.com/products/processors/index.php
Consistently write it the official way, so that it stops propagating.
Originally spotted in the documentation, it mainly affects code comments
but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output.
Found via:
git grep -i "Cortex "
git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu"
git grep -i "CortexM"
Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3483
Tested-by: jenkins
Reviewed-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The Spansion FM4 family of microcontrollers does not offer a way to
identify the chip model nor the flash size, except for Dual Flash vs.
regular layout. Therefore the family is passed as argument and
wildcard-matched - MB9BFx6x and S6E2CC families are supported.
Iterations showed that ...
1) Just doing the flash command sequence from SRAM loader code for each
half-word took 20 minutes for an 8 KB block.
2) Doing the busy-wait in the loader merely reduced the time to 19 minutes.
3) Significant performance gains were achieved by looping in loader code
rather than in OpenOCD and by maximizing the batch size across sectors,
getting us down to ~2 seconds for 8 KB and ~2.5 minutes for 1.1 MB.
(Tested with SK-FM4-176L-S6E2CC-ETH v11, CMSIS-DAP v23.)
gcc, objcopy -Obinary and bin2char.sh are used for automating the
integration of hand-written assembler snippets.
Change-Id: I092c81074662534f50b71b91d54eb8e0098fec76
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The reset-init hook for this target speeds up the CPU clock and JTAG adapter
speed. When the target is reset running with high adapter speed, a series of
warnings "DAP transaction stalled (WAIT) - slowing down" will be generated
since the adapter speed is not reduced to fit the slower CPU speed.
Fix: reduction of the adapter speed before a reset is performed.
Change-Id: Iabfc8e3f70311e0e71c8eed09b8a37fcbed9c58d
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3365
Tested-by: jenkins
Reviewed-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for the Intel Quark mcu D2000 using the new quark_d2xx
target.
Changes to the lakemont part are needed for the D2000 core and
backwards compatible with the X1000 one.
Change-Id: I6e1ef5a5d116344942f08e413965abd3945235fa
Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3199
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
niietcm4_write() buffer padding:
add correct buffer padding for 16 bytes.
Args check in FLASH_BANK_COMMAND_HANDLER():
first version of the driver had 7 args, current - 6. This patch will fix
error when flash is rejected (current k1921vk01t.cfg has flash bank init
with 6 args).
Timeouts in flash flag checking procedure:
increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check()
cause there were problems in some hardware configurations.
JTAG ID:
wrong id in k1921vk01t.cfg replaced with right one.
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Change-Id: I84296ba3eb4eeda4d4a68b18c94666f1269a500f
Reviewed-on: http://openocd.zylin.com/3171
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch fixes the tap order so that it matches the actual jtag
chain when all taps are enabled. It also introduces a variable
DEFAULT_TAPS that can be set outside of this script, e.g. on the
command line, to specify which taps are to be enabled on init.
Lastly, a new debug target "am335x.m3" is added so that the Wakeup-M3
can be selected for debugging.
Change-Id: Iccf177fda8d5e3737b1b2bb8fd1eaa7d3262ed9f
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3013
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds docs, example config, flash driver.
Driver is only supports K1921VK01T model for now.
Change-Id: I135259bb055dd2df1a17de99f066e2b24eae1b0f
Signed-off-by: Bogdan Kolbov <kolbov@niiet.ru>
Reviewed-on: http://openocd.zylin.com/3011
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Base config without flash support for now.
Change-Id: I96a5b6ad35e00dc706177ea9dbdffc384ae7f62b
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3110
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Keep clocks running in low power modes. Stop watchdogs from interfering
with the debug session. Set up PLL and increase clock at reset init.
Change-Id: I232d769d893d54e4ea9411c46c56b19587b69919
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/2707
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This is a complete flash driver for the Infineon XMC4xxx family of
microcontrollers, based on the TMS570 driver by Andrey Yurovsky.
The driver attempts to discover the particular variant of MCU via a
combination of the SCU register (to determine if this is indeed an
XMC4xxx part) and the FLASH0_ID register (to determine the variant).
If this fails, the driver will not load.
The driver has been added to the README and documentation.
Tests:
* Hardware: XMC4500 (XMC4500_relax), XMC4200 (XMC4200 enterprise)
* SWD + JTAG
* Binary: 144k, 1M
Note:
* Flash protect only partly tested. These parts only allow the flash
protection registers (UCB) to be written 4 times total, and my devkits
have run out of uses (more on the way)
Future Work:
* User 1/2(permalock) locking support via custom command
* In-memory flash loader bootstrap (flashing is rather slow...)
Change-Id: I1d3345d5255d8de8dc4175cf987eb4a037a8cf7f
Signed-off-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2488
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is a driver for the Atmel Cortex-M7 SAMV, SAMS, and SAME.
I started with the at91sam4.c driver and then restructured it
significantly to try to simplify it and limit the functionality
to just a flash driver, as well as to comply with the style guide.
Change-Id: I5340bf61f067265b8ebabd3adad45be45324b707
Signed-off-by: Morgan Quigley <morgan@osrfoundation.org>
Reviewed-on: http://openocd.zylin.com/2952
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
New configuration for NXP LPC4370 which consists of a Cortex-M4
and two Cortex-M0 cores.
Change-Id: I9918e3ff33218a14a99e4bbab9dce2e7b45b4d96
Signed-off-by: Jim Norris <u17263@att.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2124
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: La Fonera FON2200
Change-Id: Ibfdbfc9c2beca6cf436c9ee5e493b08bfb55ac85
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2839
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: Netgear WP102
Change-Id: Id93957b5d5851a272f15be35f9f448a9ce6d8a08
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2835
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Default to lpc8xx as before, but allow setting the actual CHIPNAME.
Change-Id: I5a48fa75c640440a0d4c3f2858653e94bed846d2
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3084
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek
Juha Niskanen
Jan Čapek
Matthias Welwarsky
Karl Palsson
Paul Fertser
Uwe Bonnes
Owen Kirby
Peter Lawrence
Harald Welte
Andreas Fritiofson
Andreas Färber
Ivan Meleca
Alexander Kurz
Ivan De Cesaris
Bogdan Kolbov
Matthias Welwarsky
Rémi PRUD’HOMME
Jeff Ciesielski
Morgan Quigley
Jim Norris
Oleksij Rempel