Generic Xtensa LX support extends the original Espressif/Xtensa
patch-set to support arbitrary Xtensa configurations, as defined in
a core-specific .cfg file. Not yet fully-featured. Additional
functionality to be added:
- Xtensa NX support
- DAP/SWD support
- File-IO support
- Generic Xtensa multi-core support
Valgrind-clean, no new Clang analyzer warnings
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I08e7bf8fa57c25b5d0cb75a1aa7a2ac13a380c52
Reviewed-on: https://review.openocd.org/c/openocd/+/7055
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The same flag 'jtag_poll' is currently used as local data for the
command 'poll' and to temporarily mask the target polling.
This can cause unexpected behavior if the command 'poll' is
executed while polling is temporarily masked.
Add a new flag 'jtag_poll_en' to hold the temporarily mask
condition and keep 'jtag_poll' for the 'poll' command only.
While there, change the initial assignment of 'jtag_poll' using
the proper boolean value.
Change-Id: I18dcf7c65b07aefadf046caaa2fcd2d74fa6fbae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7009
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The working area allocation routines use 4 byte word alignment.
In the corner case the size of the working area is not aligned,
target_alloc_working_area() of size = target_get_working_area_avail()
will fail because the size gets aligned up and does not fit to the area
which size is aligned down.
Align down the result of target_get_working_area_avail() to cope with that
corner case.
While on it use fancy ALIGN_... macros instead of bitwise and operator.
Change-Id: Ia2a1e861c401c2c78fe6323379a3776fb4f47b06
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7096
Tested-by: jenkins
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace the FSF boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I255ad17235ff1e01bf0aa4deed4d944e1d693ddb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7071
Tested-by: jenkins
ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32-S2 is a single core Xtensa chip.
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I2fb32978e801af5aa21616c581691406ad7cd6bb
Reviewed-on: https://review.openocd.org/c/openocd/+/6940
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The command 'flash erase_check' showed the message
'Running slow fallback erase check - add working memory'
even in the case the target didn't implement blank_check_memory.
Change return code of target_blank_check_memory() in this case
and sense it in default_flash_blank_check() and show a message
without a request for working memory.
Change-Id: I7cf9bf77742964b4f377c9ce48ca689e57d0882f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6765
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
This helps e.g. if there are 8 cores, and cores 0--3 are in one SMP
group while 4--7 are in another group. (And there are 2 gdb instances
connected, one debugging the first group, and one the second.)
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I7b6c9382eadf964529105eaf0411a42d48768668
Reviewed-on: https://review.openocd.org/c/openocd/+/6979
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This command allows users to set base working directory for the
semihosting I/O operations.Default is the current OpenOCD directory.
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I80c5979e4c96d66cccdd12cc6fcd5f353e5c6b4d
Reviewed-on: https://review.openocd.org/c/openocd/+/6888
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Removes Warning: line 6482, column 12
1st function call argument is an uninitialized value
Use target ptr directly as checked in previous lines instead of
dereferencing head->target
Change-Id: I6804b776fd493af71f3098d702f9cdc7acb50151
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6970
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In jimtcl 0.80 the prototype of Jim_DictPairs() has changed.
The only code in OpenOCD that uses Jim_DictPairs() has been merged
recently and it only uses the current jimtcl syntax.
To allow compiling OpenOCD master branch with older versions of
jimtcl, detect the version of jimtcl and use the appropriate
syntax.
Change-Id: I6fc78303b6a4db064a97f326c46119f4568e88f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: dullfire@yahoo.com
Reviewed-on: https://review.openocd.org/c/openocd/+/6948
Tested-by: jenkins
The 'set' variable name suggests a boolean data type which determines
whether a breakpoint (or watchpoint) is active. However, it is also
used to store the number of the breakpoint.
This encoding leads to inconsistent value assignments: boolean and
integer values are mixed. Also, associated hardware comparator
numbers, which are usually numbered from 0, cannot be used directly.
An additional offset is required to store the comparator numbers.
In order to make the code more readable and the value assignment more
consistent, change the variable name to 'is_set', its data type to 'bool'
and introduce a dedicated variable for the break-/watchpoint
number.
In order to make the review easier, the data types of various related
variables (e.g. number of breakpoints) are not changed.
While at it, fix a few coding style issues.
Change-Id: I2193f5639247cce6b80580d4c1c6afee916aeb82
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6319
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace 'mem2array' and 'array2mem' with a Tcl wrapper that
internally uses 'read_memory' and 'write_memory'.
The target-specific 'mem2array' and 'array2mem' functions
remain for now.
Change-Id: If24c22a76ac72d4c26916a95f7f17902b41b6d9e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6308
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
These functions are meant as replacement for 'mem2array' and
'array2mem'.
The main benefits of these new functions are:
* They do not use Tcl arrays but lists which makes it easier
to parse (generate) the data. See the Python Tcl RPC code
in contrib as a negative example.
* They do not operate on Tcl variables but instead return (accept)
the Tcl list directly. This makes the C and Tcl code base
smaller and cleaner.
* The code is slightly more performant when reading / writing
large amount of data. Tested with a simple Python Tcl RPC
benchmark.
Change-Id: Ibd6ece3360c0d002abaadc37f078b10a8bb606f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Instead of reinventing a simply linked list, reuse the list helper
for the list of targets in a smp cluster.
Using the existing helper, that implements a double linked list,
makes trivial going through the list in reverse order.
Change-Id: Ib36ad2955f15cd2a601b0b9e36ca6d948b12d00f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6783
Tested-by: jenkins
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
We have the API target_event_name().
Use it to improve code readability.
Change-Id: Ic48d2227bdefe9af05aff99a871a45e0612e5254
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6790
Tested-by: jenkins
Standard C library free() allows NULL pointer as a parameter.
Change target_free_working_area() to conform this convention.
Remove NULL pointer tests before target_free_working_area() calls.
While on it add missing setting pointer to NULL after target_free_working_area().
Change-Id: I7c692ab04a9933398ba5bc614723ad0bdecb87b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6712
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For example: before this change in cortex_m_examine, if we fail reading CPUID
we return a failure code but target was set to examined which is not consistent.
Change-Id: I9f0ebe8f811849e54d1b350b0db506cb3fdd58f4
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The jimtcl API Jim_GetCommand() sets an error message when the
command is not found and flag JIM_ERRMSG is set.
OpenOCD is checking if the command has already been registered,
thus 'command not found' is the desired case.
Pass flag JIM_NONE to prevent jimtcl from setting the error
message.
Change-Id: I3329c2f8722eda0cc9a5f9cbd888a37915b46107
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6562
Tested-by: jenkins
Commit dc7b32ea4a ("armv7m_trace: get rid of the old tpiu code")
is not handling correctly the old 'tpiu' command if it is run
during the config phase (before command 'init').
Move the call to the old event handler 'trace-config' in function
jim_arm_tpiu_swo_enable(), so it is correctly executed after
'init'.
Add the call to the old event handler 'trace-config' also during
jim_arm_tpiu_swo_disable(), to match the old behaviour.
Add more information while alerting that the event 'trace-config'
is deprecated.
Change-Id: If831d9159b4634c74e19c04099d041a6e2be3f2a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: dc7b32ea4a ("armv7m_trace: get rid of the old tpiu code")
Reviewed-on: https://review.openocd.org/c/openocd/+/6561
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
NULL is defined as 'void *'.
There is no need to cast NULL while assigning it to a pointer.
Change-Id: Ibaf18e5d47329707ec9c1c184cd4bba2e8e702ff
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6540
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
The NULL pointers preceded by cast where not detected by the
scripting tools looking for NULL pointer comparison.
Remove them and, while there, further simplify the code and apply
the other coding style rules.
Change-Id: Ia7406122e07ef56ef311579ab0ee7ddb22c8e4b5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6539
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Use the new helper to make the code more readable.
Change-Id: I11b2a79dbc6f93f6cfde382bcc00dd7ff710d908
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6375
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The existing implementation blocks in select() for a fixed amount of
time. This change tracks when the next event (likely poll()) wants to be
run, and uses a shorter timeout in select() if necessary.
Also track all these timeouts using milliseconds as returned by
timeval_ms() instead of `struct timeval` to simplify the code.
This feature is helpful if poll() wants to do something like sample PCs
or memory values for basically the entire time that otherwise OpenOCD
would be hung in select(). See
https://github.com/riscv/riscv-openocd/pull/541 for an example of that.
The RISC-V code using this change will be upstreamed some day, too.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: I67104a7cf69ed07c8399c14aa55963fc5116a67d
Reviewed-on: http://openocd.zylin.com/6363
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new checkpatch can automatically fix the code, but this
feature is still error prone and not complete.
Patch generated automatically through the new checkpatch with
flags "--types CONSTANT_COMPARISON --fix-inplace".
Some Yoda condition is detected by checkpatch but not fixed; it
will be fixed manually in a following commit.
Change-Id: Ifaaa1159e63dbd1db6aa3c017125df9874fa9703
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6355
Tested-by: jenkins
For the remaining NULL comparisons, remove then manually.
While there, make more readable a loop, by moving the assigment
out of the loop condition.
Change-Id: I44193aaa95813156a3a79c16b80e1ad333dc1eaf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6353
Tested-by: jenkins
Patch generated automatically through a modified checkpatch that
detects the patterns
if (NULL == symbol)
if (NULL != symbol)
and through flags "--types COMPARISON_TO_NULL --fix-inplace".
The unmodified checkpatch detects this pattern as Yoda condition,
but it's odd fixing it as Yoda condition and then again as NULL
comparison. This triggered the modification to the script.
Change-Id: I5fe984a85e9c4fc799f049211797aef891ebce18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6352
Tested-by: jenkins
Patch generated automatically through the new checkpatch with
flags "--types COMPARISON_TO_NULL --fix-inplace".
This only fixes the comparisons
if (symbol == NULL)
if (symbol != NULL)
The case of NULL on the left side of the comparison is not tested.
Some automatic fix is incorrect and has been massaged by hands:
- if (*psig == NULL)
+ if (*!psig)
changed as
+ if (!*psig)
Change-Id: If4a1e2b4e547e223532e8e3d9da89bf9cb382ce6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6351
Tested-by: jenkins
There are more than 1000 NULL comparisons to be aligned to the
coding style.
For recurrent NULL comparison it's preferable using trivial
scripts in order to minimize the review effort.
Patch generated automatically with the command:
sed -i PATTERN $(find src/ -type f)
where PATTERN is in the list:
's/(\([a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) == NULL)/(!\1)/g'
's/(\([a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(\([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\) != NULL)/(\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL == \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(!\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*->[a-z][a-z0-9_]*\))/(\1)/g'
's/(NULL != \([a-z][a-z0-9_]*\.[a-z][a-z0-9_]*\))/(\1)/g'
Change-Id: Ida103e325d6d0600fb69c0b7a1557ee969db4417
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6350
Tested-by: jenkins
No major cross dependencies, mostly changes internal to each
file/function.
Change-Id: I7cc87458a341bae29a4f772b0af5d97b4bfc2da3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6343
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
There are ~900 Yoda conditions to be aligned to the coding style.
For recurrent Yoda conditions it's preferable using a trivial
script in order to minimize the review effort.
E.g. comparison of uppercase macro/enum with lowercase variable:
- ...(ERROR_OK == retval)...
+ ...(retval == ERROR_OK)...
Patch generated automatically with the command:
sed -i \
's/(\([A-Z][A-Z0-9_]*\) \([=!]=\) \([a-z][a-z0-9_]*\))/(\3 \2 \1)/g' \
$(find src/ -type f)
While there, remove the braces {} around a single statement block
to prevent warning from checkpatch.
Change-Id: If585b0a4b4578879c87b2dd74d9e0025e275ec6b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6354
Tested-by: jenkins
Reviewed-by: Xiang W <wxjstz@126.com>
- Added support for reading and writing 64-bit data items
using TCL commands "mem2array" and "array2mem". Until now,
data items only up to 32 bits were supportd.
- Cleaned up functions target_array2mem() and
target_mem2array(), especially data types of variables
and variable declarations (scope).
Change-Id: Ia0ba427804f8fd8d7568f12714ab36984d6d5e24
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6286
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add 64-bit address support to the target mem2array and array2mem commands
Change-Id: Ibdcc076ca5581f4fd87e92318aab33907e22d6ce
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/6246
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- In "reg" TCL command handler, the return value of register get()
and set() callbacks must be checked, in the same manner as it is
done in e.g. gdb_set_register_packet() or gdb_get_register_packet().
- Minor cleanup of variable definitions in the "reg" command
handler.
Change-Id: I8c57e7c087fe31d1abffa3c4d1f79a01af4c9c97
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6293
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is used to compute memory block read alignment, and specifically
allows 64-bit targets to ensure that memory block reads are only
requested on 64-bit boundaries.
Signed-off-by: Tim Newsome <tim@sifive.com>
Change-Id: Idb1a27b9fc02c46245556bb0f3d6d94b368c4817
Reviewed-on: http://openocd.zylin.com/6249
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With the API fixed to comply with OpenOCD coding style, fix all
the references in the code.
Patch generated automatically with the script below.
The list is in reverse order to replace a common prefix after the
replacement of the symbols with the same prefix.
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
Jim_SetResult_NvpUnknown jim_set_result_nvp_unknown
Jim_Nvp_value2name_simple jim_nvp_value2name_simple
Jim_Nvp_value2name_obj jim_nvp_value2name_obj
Jim_Nvp_value2name jim_nvp_value2name
Jim_Nvp_name2value_simple jim_nvp_name2value_simple
Jim_Nvp_name2value_obj_nocase jim_nvp_name2value_obj_nocase
Jim_Nvp_name2value_obj jim_nvp_name2value_obj
Jim_Nvp_name2value_nocase_simple jim_nvp_name2value_nocase_simple
Jim_Nvp_name2value_nocase jim_nvp_name2value_nocase
Jim_Nvp_name2value jim_nvp_name2value
Jim_Nvp struct jim_nvp
Jim_GetOpt_Wide jim_getopt_wide
Jim_GetOpt_String jim_getopt_string
Jim_GetOpt_Setup jim_getopt_setup
Jim_GetOpt_Obj jim_getopt_obj
Jim_GetOpt_NvpUnknown jim_getopt_nvp_unknown
Jim_GetOpt_Nvp jim_getopt_nvp
Jim_GetOpt_Enum jim_getopt_enum
Jim_GetOpt_Double jim_getopt_double
Jim_GetOpt_Debug jim_getopt_debug
Jim_GetOptInfo struct jim_getopt_info
Jim_GetNvp jim_get_nvp
Jim_Debug_ArgvString jim_debug_argv_string
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find src -type f ! -name jim-nvp.\? )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
Change-Id: I10a12bd64bb8b17575fd9150482c989c92b298a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6184
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Some help text end with a useless space character.
Remove it.
Change-Id: I397e1194fac8042f0fab694222f925f906716de3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6222
Tested-by: jenkins
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I548581247db72e683249749d1b8725035530b06e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6217
Tested-by: jenkins
While still keeping the tree of struct command, stop registering
commands in jim by the root "word" only.
Register the full-name of the command and pass as private data the
struct command of the command itself.
Still use the tree of struct command to un-register the commands.
Some "native" commands (.jim_handler) share the same handler, then
the handler checks the command name to run the right code.
Now argv[0] returns the full-name of the command, so check the
name by looking in the struct command passed as private data.
Change-Id: I5623c61cceee8a75f5d5a551ef3fbf5a303af6be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5671
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
In current code the current target is overridden whenever
jim_handler_data is not NULL. This happens not only with target
prefixed commands, but also with cti, dap and swo/tpiu prefixed
commands.
While this is not causing any run-time issue, by now, the
behaviour is tricky and makes the code cryptic.
Add a specific field to struct command for the target override so
the content of jim_handler_data can be restricted to command
specific data only (today only cti, dap and swo/tpiu).
Extend the API register_commands() to specify the presence of
either the command data or the override target.
The new API makes obsolete calling command_set_handler_data() to
set jim_handler_data, so remove it.
Change-Id: Icc323faf754b0546a72208f90abd9e68ff2ef52f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5667
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Now that target override is uniformly implemented for all types of
commands, there is no need for target-prefixed "native" commands
(.jim_handler) to sneakily extract the overridden target from the
struct command.
Modify the commands to use the standard API get_current_target().
Change-Id: I732a09c3261e56524edd5217634fa409eb97a8c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5666
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While registering a new command, jim accepts a pointer to command's
private data that will be accessible during the command execution.
Today openocd is not consistent and passes different private data
depending on the command, and then even overwrites it:
- "simple" commands (.handler) are registered with their own
struct command pointer as command private data;
- "native" commands (.jim_handler) at root level are registered
with NULL command private data;
- "native" commands (.jim_handler) not at root level are
registered with the struct command pointer of their root command
as command private data but, when executed, the command private
data is overwritten by the value in field jim_handler_data taken
from their struct command.
Uniform the usage of command private data by always set it to the
struct command pointer while registering the new commands.
Note: for multi-word commands only the root command is registered,
so command private data will be set to the struct command of the
root command. This will change later in this series when the full-
name of the command will be registered.
Don't overwrite the command private data, but let the commands that
needs jim_handler_data to get it directly through struct command.
For sake of uniformity, let function command_set_handler_data() to
set the field jim_handler_data also for "group" commands, even if
such value will not be used.
Now Jim_CmdPrivData() always returns a struct command pointer, so
wrap it in the inline function jim_to_command() to gain compile
time check on the returned type.
While there, uniform the code to use the macro Jim_CmdPrivData()
to access the command's private data pointer.
Change-Id: Idba16242ba1f6769341b4030a49cdf35a5278695
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5664
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
We do not have anymore any deprecated target name.
Drop the code to handle deprecated target names and the placehold
in struct target_type.
This patch is separated from the patch that drops the remaining
deprecated target names to be ready to revert this if there is any
need in the future.
Change-Id: I96fca7ffa39d8292f81e79f115ea45c4a30035d7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6087
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
target->endianness is initialized to TARGET_ENDIAN_UNKNOWN at 34 lines
below, before calling target_configure. This initialization is
redundant and not needed.
Change-Id: Iea2d5e17a13c1a8b0b209ba7c20043736b520ef6
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: http://openocd.zylin.com/6039
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD is based on a single main loop that schedules all the
activities.
At the execution of a TCL command, the timestamp is checked to
eventually trigger the polling of the targets. This means that by
executing a TCL command the polling can be triggered and detect a
change of target's state.
When openocd 'resumes' a target, the target can halt again by
hitting a breakpoint.
The 'resumed' event handler is started just after the target has
been resumed, but it triggers a polling before the execution of
its very first instruction.
If the polling finds the target halted, it will run the 'halted'
event handler, that will then be executed 'before' the pending
'resumed' handler.
In case of gdb, a 'continue' command will restart the target but,
polling (and halt detection) executed before the end of the resume
process will hide the halt. As a consequence, the gdb will not be
informed of the halt and will remains waiting as if the target is
still running without showing the prompt.
This can be verified by running on the target a firmware with a
loop, run openocd with a dummy 'resumed' event, and let gdb to set
a breakpoint in the loop. A 'continue' command will cause the
target to halt again by hitting the breakpoint at the next loop
iteration, but gdb will loose it and will not return the prompt.
openocd -f board/st_nucleo_f4.cfg -c \
'stm32f4x.cpu configure -event resumed {echo hello}'
arm-none-eabi-gdb -ex 'target remote :3333' -ex 'b *$pc' -ex c
Disable the polling while executing target's resume().
Document it and provide hints to developers to cope with future
implementation.
Change-Id: I3be830a8e7c2ef6278617cb4547a4d676b0ddeb5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Габитов Александр Фаритович <gabitov@planarchel.ru>
Reviewed-on: http://openocd.zylin.com/6074
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Currently wp/rwp commands fail on 64-bit targets:
> wp 0xffffffff80001400 4
addr option value ('0xffffffff80001400') is not valid
Change-Id: I94d4af906b02b7bd463c8d79a6235a3646dfc434
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-on: http://openocd.zylin.com/6058
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
In the odd case of multiple flags '-gdb-port' during 'target
create' or following 'configure', the new strdup()'ed value will
replace the old one without freeing it.
Free the old value (if it exists) before replacing it.
Change-Id: I1673346613ce7023880046e3a9ba473e75f18b8a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6005
Tested-by: jenkins
Introduce a 'hidden' flag in struct reg to support a register cache
containing different views of same data: e.g. Cortex-M has
primask, basepri, faultmask and control registers accessed
as one word. With the hidden flag we can add an reg_list item
corresponding to hw access without exposing the register to user level.
All the struct reg are allocated with calloc() but one in xscale.c
allocated by malloc(). Change this one to use calloc() as well
to guarantee initial value hidden=false
Change-Id: I8da9f5a5a60777ae7ef943a841307487bd80fc6f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5325
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
When a target examination fails, continue to examine subsequent targets.
Return the number of targets that failed to examine.
Change-Id: I883a0c445edc7eb00f496b79271d773771ec6b66
Signed-off-by: Kevin Yang <kangyang@google.com>
Reviewed-on: http://openocd.zylin.com/5855
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I9f97571a528f0cb3c3c26f873577ab16fdec3cdc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Is it possible to run OpenOCD without any target, for example to
only dump the rom-tables of an arm dap, or to perform low level
jtag operations.
But without any target created, the command 'target current'
causes OpenOCD to abruptly exit.
Handle in command 'target current' the case of no targets.
Change-Id: Ide15cb13bec84b88ccc3e7126523c04a6d70e636
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5881
Tested-by: jenkins
The default way of working is to have a single GDB attached to one
target, so OpenOCD accepts only one connection to the GDB port of
each targets and rejects any further connection.
There are some barely safe use cases in which it could get useful
having a second GDB connection to the same target.
One such use case is while using GDB as a 'non-intrusive memory
inspector', as explained in the OpenOCD documentation.
One GDB can be left running an infinite loop to dump some memory
area, or even analysing the content, while keeping a second GDB
ready for user interaction or spot memory check.
Add a target configure option to specify the maximum number of GDB
connections allowed for that target, keeping the default to 1.
Change-Id: I4985a602e61588df0b527d2f2aa5b955c93e125e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5865
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Now that it’s possible to start profiling from either a running or a
halted state, rather than unconditionally halting after profiling
finishes, it makes more sense to restore the processor to whatever state
(running or halted) it was in before profiling started.
Change-Id: If6f6e70a1a365c1ce3b348a306c435c220b8bf12
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5237
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Cortex-M implementation of profiling contains a bunch of
conditionals and checks to handle both chips which have PCSR and chips
which do not. However, the net effect of the non-PCSR branches is
actually exactly the same as what target_profiling_default does. Rather
than duplicating this code, just detect the situation where PCSR isn’t
available and delegate to target_profiling_default.
Change-Id: I1be57ac77f983816ab6bf644a3cfca77b67d6f70
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5236
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are a handful of implementations of profiling. There is the
default implementation, which repeatedly halts and resumes the target,
sampling PC each time. There is the Cortex-M implementation, which
uses PCSR if available, otherwise falling back to halting and resuming
and sampling PC. There is the OR1K implementation, which reads NPC
repeatedly. Finally, there is the NDS32 implementation which uses some
kind of AICE commands with which I am unfamiliar.
None of these (with the possible exception of the NDS32
implementation) actually require the target to be halted when starting
profiling. The Cortex-M and OR1K actually resume the target as pretty
much their first action. The default implementation doesn’t do this,
but is written in such a way that the target just flips back and forth
between halted and running, and the code will do the right thing from
either initial state. The NDS32 implementation I don’t know about.
As such, for everything except NDS32, it is not really necessary that
the target be halted to start profiling. For the non-PCSR Cortex-M and
default implementations, there is no real harm in such a requirement,
because profiling is intrusive anyway, but there is no benefit. For
the PCSR-based Cortex-M and the OR1K, requiring that the target is
halted is annoying because it makes profiling more intrusive.
Remove the must-be-halted check from the target_profiling function.
Add it to the NDS32 implementation because I am not sure if that will
break when invoked with a running target. Do not add it to any of the
other implementations because they don’t need it.
Change-Id: I479dce999a80eccccfd3be4fa192c904f0a45709
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5235
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
In target/openrisc/jsp_server.c, an error is logged if the ptr was
already NULL. This cannot happen since the pointer was already
referenced few lines before and openocd would have been already
SIGSEGV in that case, so remove the log.
Change-Id: I290a32e6d4deab167676af4ddc83523c830ae49e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5809
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
While there, fix prototype mismatch between header and C file of
the function armv7a_l1_d_cache_inval_virt().
Change-Id: I434bd241fa5c38e0c15d22cda2295097050067f5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5818
Tested-by: jenkins
While loading to flash with debug level at least 3,
OpenOCD tries to print the whole loaded bitstream.
This will be very-very-slow due to implementation of
conversion from buffer to string.
* fix condition on selected debug level in jtag/core.c
* replace slow buf_to_str function from helper/binarybuffer.c
with faster but_to_hex_str function
Change-Id: I3dc01d5846941ca80736f2ed12e3a54114d2b6dd
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
Reviewed-on: http://openocd.zylin.com/5800
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
There are failure cases of target_create() that are not checked.
Plus, in case of failure the memory allocated in not properly
released before returning error.
Check all the possible failure in target_create().
Change current_target only when target is successfully created.
Add the new target to all_targets list only when target is
successfully created.
Release all the allocated memory before quit on failure.
Use malloc() instead of calloc() for target->type, because the
struct will be fully populated with memcpy().
Change-Id: Ib6f91cbb50c28878e7c73dc070b17b8d7d4e902f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5776
Tested-by: jenkins
If a target is not examined when the debugger tries to connect to it
then it can lead to undesired/undefined behavior.
In particular it leads to a zero pointer dereference on the aarch64.
Change-Id: I67f2b714ab8b2727fd36f3de16d7f9017b4c55fe
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5727
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
Before commit b3ce5a0ae5 ("target: use LOG_USER to print errors
in events") an error in an event handler was silently lost, while
now the associated message is printed out.
A "shutdown" command in a target event (e.g. in gdb-detach) causes
the event to end with error code ERROR_COMMAND_CLOSE_CONNECTION,
that triggers the error message:
shutdown command invoked
Error executing event <event-name> on target <target-name>:
The error code returned by the command "shutdown" is required to
stop the execution in a script/proc and avoid executing any
further command in the script/proc.
It is then normal to get an error code from the "shutdown" command
and it should not be printed out.
Intercept the return code of the event in case of "shutdown", then
skip scheduling other target events and return without printing
the incorrect error message.
Change-Id: Ia3085fb46beacb90a5e4bf0abf7c6e28bb9e6a9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Laurent Lemele <laurent.lemele@st.com>
Reviewed-on: http://openocd.zylin.com/5710
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
The jim library exports all the data types through typedef, so
there is no need to use the internal struct types.
Fix the few remaining inconsistencies in the code.
Change-Id: Id4ae0083563ea7a371833374e7b39f17158f66a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5662
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
BUILD_TARGET64 creates a larger test matrix and mostly gates the
building of the aarch64/armv8 target, make that unconditional, which
would help fixing any issues with 64-bit address types anyway.
Rebased by Antonio Borneo after commit 1fbe8450a9 ("mips: Add
MIPS64 support")
Change-Id: I219f62b744d540d9dde9a42e6b63fd7d91df3dbb
Suggested-by: Matthias Welwarsky <matthias@welwarsky.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5240
Tested-by: jenkins
Events TARGET_EVENT_STEP_START and TARGET_EVENT_STEP_END
have been added - analogous to already existing events
TARGET_EVENT_RESUME_*.
This is an example of a concrete use case where having
these events is important:
In RISC-V processors without Debug Program Buffer, OpenOCD
cannot execute fence/fence.i when resuming or single-
stepping. With these events implemented, the user can
instead provide custom operations to achieve that same
effect prior to resuming the processor.
Change-Id: I786348ff08940759d99b0f24e9e0ed5a44581094
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5551
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The memory leak can be reproduced by using an arbitrary RTOS
and valgrind:
$ valgrind --leak-check=full --show-leak-kinds=all
[...]
==9656== 224 (80 direct, 144 indirect) bytes in 1 blocks are definitely lost in loss record 3 of 3
==9656== at 0x483CD99: calloc (in /usr/lib/x86_64-linux-gnu/valgrind/vgpreload_memcheck-amd64-linux.so)
==9656== by 0x1C541A: os_alloc (rtos.c:79)
==9656== by 0x1C569E: os_alloc_create (rtos.c:111)
==9656== by 0x1C569E: rtos_create (rtos.c:153)
==9656== by 0x1AE332: target_configure (target.c:4899)
==9656== by 0x1AF228: jim_target_configure (target.c:4952)
==9656== by 0x1C9EF9: command_unknown (command.c:1066)
==9656== by 0x313284: JimInvokeCommand (jim.c:10364)
==9656== by 0x313FB6: Jim_EvalObj (jim.c:10814)
==9656== by 0x3154A3: Jim_EvalFile (jim.c:11207)
==9656== by 0x316015: Jim_SourceCoreCommand (jim.c:15230)
==9656== by 0x313284: JimInvokeCommand (jim.c:10364)
==9656== by 0x313B8B: JimEvalObjList (jim.c:10605)
[...]
Change-Id: I2cd41a154fb8570842601ff4e3e76502f5908f49
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5479
Tested-by: jenkins
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The jimtcl commit 41c5ff1809f5 ("jim.c: Fix Object leak in zlib
support") https://repo.or.cz/jimtcl.git/commit/41c5ff1809f5
makes Jim_SetResultFormatted() freeing the parameters that have
zero refcount.
OpenOCD commit 559d08c19e ("jim tests: use installed") adds the
only code instance in OpenOCD that first passes a zero refcount
object to Jim_SetResultFormatted() and then frees it.
By switching jimtcl version to 0.78 or newer this causes a crash
of OpenOCD.
To trigger the crash in a telnet session, check that the current
target is running and type:
[target current] arp_waitstate halted 1
Remove the call to Jim_FreeNewObj() after the call to
Jim_SetResultFormatted().
Change-Id: I5f5a8bca96a0e8466ff7b789fe578ea9785fa550
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5453
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A configuration script may want to check the reason why examine fails
e.g. device has security lock engaged.
tcl/target/kx.cfg and klx.cfg is modified to use the new event
for testing of the security lock of Kinetis MCU
Change-Id: Id1d3a79d24e84b513f4ea35586cd2ab0437ff9b3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4289
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch is an initial bump of ARC-specific code
which implements the ARCv2 target(EMSK board) initializing
routine and some basic remote connection/load/continue
functionality.
Changes:
03.12.2019:
-Add return value checks.
-Using static code analizer next fixes were made:
Mem leak in functions:
arc_jtag_read_memory,arc_jtag_read_memory,
arc_jtag_write_registers, arc_jtag_read_registers,
jim_arc_add_reg_type_flags, jim_arc_add_reg_type_struct,
arc_build_reg_cache, arc_mem_read.
Dead code in "arc_mem_read";
In arc_save_context, arc_restore_context correct arguments
in"memset" calls.
In "build_bcr_reg_cache", "arc_build_reg_cache" check
if list is not empty.
29.12.2019
-Moved code from arc_v2.c to arc.c
-Added checks of the result of calloc/malloc calls
-Reworked arc_cmd.c: replaced spagetty code with functions
-Moved to one style in if statements - to "if(!bla)"
-Changed Licence headers
22.01.2020
-Removed unused variables in arc_common
-Renamed register operation functions
-Introduced arc_deinit_target function
-Fixed interrupt handling in halt/resume:
* add irq_state field in arc_common
* fix irq enable/disable calls ( now STATUS32 register is used)
-Switched from buf_set(get)_us32() usage to target_buffer_set(get)_u32()
-Made some cleanup
30.01.2020
-Removed redundant arc_register struct, moved target link to arc_reg_desc
-Introduced link to BCR reg cache in arc_common for freeing memory.
-Now arc_deinit_target frees all arc-related allocated memory.
Valgrind shows no memory leaks.
-Inroduced arch description in arc.c
01.02.2020
-Remove small memory allocations in arc_init_reg. Instead created reg_value
and feature fields in arc_reg_desc.
-Add return value for arc_init_reg() func.
-Replaced some integer constants(61,62,63) with defines.
-Removed redundant conversions in arc_reg_get_field().
-Moved iccm/dccm configuration code from arc_configure()
to separate functions.
19.02.2020
-Change sizeof(struct) to sizeof(*ptr) in allocations
-Changed if/while(ptr != NULL) to if/while(ptr)
-Removed unused variables from struct arc_jtag
-Add additional structs to arc_reg_data_type
to reduce amount of memory allocations calls
and simplifying memory freeing.
-Add helper arc_reg_bitfield_t struct which includes
reg_data_type_bitfield object and char[] name. Reduces
memory allocations calls.
-Add limit for reg_type/reg_type_field names(20 symbols).
-Add in jim_arc_add_reg_type*() functions additional
argnument checks(amount of field/name size).
-In jim_arc_add_reg_type*() reduced amount of memory allocations.
-Cleanup of jim_arc_add_reg_type*() functions.
-For commands update ".usage" fields according docopt.
-Cleanup in arc_jtag.c
-Renamed functions which require jtag_exeutre_queue() to arc_jtag_enque_*()
-Add arc_jtag_enque_register_rw() function, which r/w to jtag ir/dr regs
during regiter r/w.
24.02:
-Change include guards in arc* files according coding style
-Remove _t suffix in struct arc_reg_bitfield_t
-Some cleanup
Change-Id: I6ab0e82b12e6ddb683c9d13dfb7dd6f49a30cb9f
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/5332
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
The `value` variable is passed into `target_fill_mem` as its
second-to-last parameter. That parameter is of type `uint64_t`. It is
appropriate to parse the value as that type, since otherwise a target
with a 32-bit address space but 64-bit data write capabilities would not
be able to exercise those capabilities.
Change-Id: Ib336d47d42c27cd2b5ba1206b04e8f740f167dba
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5219
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The current code checks the count to determine whether to read bytes or
words. However it fails to consider whether the base address is suitably
aligned.
Instead use the target_read_buffer() function which is for exactly this
purpose and generates optimal accesses with natural alignment.
Change-Id: I32ab5417890ee2219902df1529bc220fe353b4c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3217
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
1. Add get_thread_reg() to rtos. It's used in rtos_get_gdb_reg() to read
the value of a single register, instead of reading all register values
by calling get_thread_reg_list().
2. Add set_reg() to rtos. gdb_server uses this to change a single
register value for a specific thread.
3. Add target_get_gdb_reg_list_noread() so it's possible for gdb to get
a list of registers without attempting to read their contents.
The clang static checker doesn't find any new problems with this change.
Change-Id: I77f792d1238cb015b91527ca8cb99593ccc8870e
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/5114
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of target's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition, thus dumping the
call-trace. The execution is not stopped because the error is not
further propagated, but the error message is annoying and
misleading.
It can be tested running
openocd -f ./test.cfg
using the following script "test.cfg". You can replace the board
file in line 1, to use a board available in your lab:
1 source [find board/st_nucleo_f4.cfg]
2 [target current] configure -event reset-start {}
3 [target current] configure -event reset-end {return}
4 init
5 proc a {} {[target current] invoke-event reset-start}
6 proc b {} {[target current] invoke-event reset-end}
7 proc c {} {a;b;echo "arrived at the end"}
8 c
9 shutdown
The execution produces:
./test.cfg:7: Error:
in procedure 'c' called at file "./test.cfg", line 8
in procedure 'b' called at file "./test.cfg", line 7
arrived at the end
that shows the call-trace but does not halt the execution.
The developer can avoid using the "return" command in the event
body by defining a TCL procedure that implements the handler and
that contains the "return" command, reducing the handler body to
a simple call to the procedure above. But this approach is either
not documented nor always intuitive while writing the handler,
causing waste of time to look for the false error.
Modify target_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I2b860bab7233c6ed13ee4098e348d7533e1c4626
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4974
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Before commit 877cec20dc
("command: check command mode for native jim commands") all the jim commands
were erroneously treated as they had mode COMMAND_ANY.
The command '$_TARGET configure -xxx' was therefore applicable on running
OpenOCD to change the target configuration. It is handy e.g. for changing
an event handler or changes of the work area.
Change 'configure' command .mode to COMMAND_ANY to make it possible again.
The only parameter which cannot be re-configured after init is -gdb-port.
Test the command mode and refuse setting of gdb port after init.
Change-Id: I88493ac10a46647dc52a88fbc9f8ce6b5ba3bcd0
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5214
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Remove a copy of handle_md_output() from src/target/dsp563xx.c
Change-Id: Iadd003fd1dcdbc7990d46a58ee2e7c30826ac6af
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5175
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Left unused after commit "target: unify memory read/write
commands", can be removed.
Change-Id: Iea6ef9204c8071283a66a679b3d6edbb0c929c5c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5153
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Part of the output is generated with log functions.
Change prototype of find_target() and use command_print() for all
the output of the command.
Change-Id: Ia9fdb653fd5b27be427381053a037545faa34414
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5092
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of binprint() to pass CMD instead of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I5ebdc50417d97c791c98ac0cfe2218319809eb7f
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5077
Tested-by: jenkins
Ian Thompson
Antonio Borneo
Tomas Vanek
Erhan Kurubas
Tim Newsome
Marc Schink
Zoltán Dudás
Yasushi SHOJI
Tarek BOCHKATI
Jan Matyas
Daniel Goehring
R. Diez
Peter Mamonov
Andreas Bolsch
Kevin Yang
Christopher Head
Samuel Obuch
Mikhail Rasputin
Florian Fainelli
Marc Schink
Evgeniy Didin
Andreas Fritiofson
Paul Fertser